new loctite® 4090™ structural instant adhesive hybrid — combines speed and strength
TRANSCRIPT
New Loctite 4090 Structural Instant Adhesive Hybrid –
Combines Speed and Strength
q This webinar will be available afterwards at www.designworldonline.com & email
q Q&A at the end of the presentation q Hashtag for this webinar: #DWwebinar
Before We Start
Moderator Presenters
Lee Teschler Design World
Nicole Lavoie Henkel Corporation
Doug Lescarbeau Henkel Corporation
LOCTITE® 4090TM
HYBRID ADHESIVE
The Product
Features & Benefits
Packaging & Application
Applications
Key Technical Data
Discussion
1
2
3
4
5
6
AGENDA
6
THE PRODUCT 1
The first hybrid structural instant adhesive: Speed & Strength in One
HYBRID TECHNOLOGY
High Bond Strength and Impact Resistance
Speed and Substrate Versatility
STRUCTURAL INSTANT
LOCTITE® 4090TM THE FIRST HYBRID STRUCTURAL INSTANT ADHESIVE – SPEED AND STRENGTH IN ONE
• Unique Hybrid technology – U.S. patent protected
• Highest combination of critical attributes in one product
• First instant adhesive suitable for structural applications
• Opens new application areas
FEATURES & BENEFITS 2
10
Features & Benefits
STRENGTH SPEED HIGH IMPACT RESISTANCE
HIGH MOISTURE RESISTANCE
GAP FILLING UP TO 0.2”
UP TO 300o F TEMPERATURE
RESISTANCE
SPEED
Characteristics AMBIENT (21 C) COLD TEMP (5 C) Zero Gap Fixture Time:
60 - 90 seconds
120 - 180 seconds
Gap Fixture Time: 0.04” 0.08” 0.2”
3 - 5 minutes
3 - 6 minutes (0.04”)
Nozzle Life Approx. 4 minutes
Gap filling Up to 0.2”
POLYCARBONATE ACRYLIC
ABS RUBBER
ALUMINUM STEEL
BONDS TO A WIDE RANGE OF SUBSTRATES
Substrate N/mm2 psi Steel 17 2,420 Stainless 15 2,120
Aluminum 7.6 1,100 Nitrile 0.7 100 ABS 5.2 750 Polycarbonate 6.9 1,000 Epoxy 9.1 1,320 Wood (Oak) 4.8 700
POLYCARBONATE ACRYLIC
ABS RUBBER
ALUMINUM STEEL
BONDS TO A WIDE RANGE OF SUBSTRATES
IMPACT RESISTANCE
IMPACT RESISTANCE
Side Impact Results Inch – Lbs
44
35
26
18
8
HEAT RESISTANCE
1000 Hours Heat Aging on GBMS Strength (psi)
CA = 0
2900
2175
1450
725
150oF/95% Relative Humidity Aging GBMS % Strength Retention
CA = 0
MOISTURE RESISTANCE
% Retention
Lap shears of Grit-Blasted Mild Steel (GBMS) are bonded and then exposed to 150oF and 95% relative humidity for times shown. Then lap shears are pulled apart and the % of the original strength is shown.
~85%
~62%
~37%
0%
After 1,000 hours, a generic CA bonded GBMS lap shear fell apart.
PACKAGING & APPLICATION 3
PACKAGING
• Two-part product
• Mix ratio 1:1
• Dual syringe
• 50 ml
• 400 ml (April 2015)
• Package includes five mixer nozzles.
• Manual dispense with 1:1 dispense gun
• Semi and fully automatic dispense with positive
displacement
APPLICATION METHODS
4 APPLICATIONS
• Where the combination of speed, toughness, moisture resistance and gap filling is required
• Where outdoor use, UV protection and low blooming is required
• Where standard cyanoacrylates prove to be too brittle
• Where high moisture and temperature resistance is demanded • For structural applications demanding speed, ease of use and bonding of
multiple substrates including plastics
A technological breakthrough suitable for a broad range of applications.
Applications
LOCTITE® 4090TM
5 KEY TECHNICAL DATA
TECHNICAL DATA
Color Clear to light yellow depending on gap fill
Appearance High viscosity gel
Mix ratio (volume) 1:1
Working time 3 to 5 minutes
Shelf life (total) 12 months refrigerated. Package is stamped with a Use-By date.
PROPERTIES OF CURED MATERIAL
Lap shear strength, ISO4587, after 24 hours, 72oF
Steel (grit blasted) Aluminum (etched) Polycarbonate
2400 psi 1900 psi 1000 psi
High gap fill Up to 0.2” depending on bond geometry
Temperature resistance -40oF to 300oF
Chemical resistance Very good chemical/solvent resistance against motor oil, gasoline, ethanol, isopropanol, and water.
Questions? Lee Teschler Design World [email protected] Twitter: @DW_LeeTeschler
Nicole Lavoie Henkel Corporation [email protected] Phone: 860.571.5129
Doug Lescarbeau Henkel Corporation [email protected] Phone: 860.571.5279
Thank You q This webinar will be available at
designworldonline.com & email q To learn more about Loc/te® 4090™, visit:
www.henkelna.com/4090
q Tweet with hashtag #DWwebinar
q Connect with Design World
q Discuss this on EngineeringExchange.com
Presenters
Doug Lescarbeau Doug Lescarbeau works for Henkel Corporation. Doug is the Market Development Director for the North American General Business. He works in Rocky Hill, Connecticut at Henkel’s North American headquarters. He has a BS in Chemistry from the University of Hartford, CT and a MBA from Loyola College of Baltimore, MD. During his career at Henkel, he worked with Loctite brand products in R&D, Technical Service, Sales and Marketing. In his role as Market Development Director, he is responsible for the identification and development of business opportunities for the General Business unit.
Presenters
Nicole Lavoie Nicole Lavoie is a Regional Application Engineer and has been with Henkel Corporation for 2 years. As a Henkel Application Engineer, Nicole designs and implements programs to develop the technical data needed to support the use of Henkel adhesives, sealants and surface treatments. Nicole works directly with Henkel customers to identify, qualify, close, and maintain Henkel Product applications. Nicole also focuses on cyanoacrylate adhesive technologies. This experience has allowed Nicole to become a dedicated expert on Henkel’s new hybrid adhesive – Loctite 4090 – which combines the speed of an instant adhesive with the strength of a structural adhesive.