netprobe 2000 t1e1 analyzer...2012/12/06 · e1 general: 2048 kbs e1 interface: per ccitt g.703,...
TRANSCRIPT
NetProbe 2000 T1E1 Analyzer
The NetProbe 2000 represents the latest generation of handheld telecom analyzers built on technologies powering today’s smartphones and tablets...
Design Highlights
Rugged, lightweight and compact ABS chassis with rubber bumper
1Ghz processor for quick boot-up, interaction and complex measure-ments at low power.
Easy to operate touchscreen GUI with alternate operation via 5-way navigation keypad
Multifunctional design provides cost effectiveness and convenience
State-of-art 2011design guarantees a 10+ years long life cycle.
Unmatched oversize Li-Ion polymer battery life
Convenience of Ethernet, USB and optional WiFi/bluetooth.
Key Features
T1 & E1 Applications Summary
Circuit turn up and monitoring
Physical layer testing of signal level, frequency, clock slips, pulse mask analysis
Frame layer errors and alarms monitoring and simulation
BERT and fractional BERT testing end-to-end and looparound
T1 CSU loop up and down code send
Offsetting trasmitter clock to stress receivers
Data BERT testing via RS-232, RS-530, RS-449, V.35, X.21 or Co-dir interfaces
Voice and data delay measurements
Supports E1, DS1(T1) testing
Optional E3, DS3(T3) testing
Combines legacy PDH/TDM inter-faces with IP network testing in the smallest handheld available
ISDN PRI protocol analysis and call emulation
Full rate Wi-Fi access and optional test across 802.11 b/g/n/bluetooth
Datacom DTE and DCE BERT test-ing on RS-232, RS-530, RS-449, V.35 and co-dir 64kb
T1,E1 BERT, G.821, G,826, RFC 1406 and M.2100 analysis
Histograms for errors and alarms
Powerfull test results dBase re-cording, reporting and exporting to USB flash or printing
nx56/64kb round trip delay
T1, E1 pulse mask verification
VNC based remote control via LAN, WAN, Internet
Remote control via Android phone ap
3D VIEW
10/100 Base-T LAN port for IPTV and VoIP test in transparent ( passive) mode
10/100 Base-T WAN port for IPTV and VoIP primary interface or 10/100/1000 Base-T Gigabit test interface
SFP interface for removable 1000Base-SX, 1000Base-LX or 1000Base-ZX optical transceiver
Mini-USB con-nector for USB OTG host or slave access
NP2000-DCOM option connector provides datacom bit error testing interface for RS-232, RS-530, V.35, RS-449, X.21 or G.703 co-dir interface.
Audio headset access via the miniUSB type connector
External clock for E1 ,T1, E3 or T3 transmitter clock-ing on SMA connector
T1,E1 or G.703 64kb co-dir interface avail-able on RJ-45 or Bantam
E1,T1, E3 or T3 receiver with BNC connector
E1,T1, E3 or T3 transmitter with BNC connector
Rubber overmold provides non-slip grip, protection and water resistance.
Detachable Wi-Fi antenna for increased signal sensitivity to im-prove coverage and provide accu-rate signal strength
3.5” TFT color touch-screen with bright white LED backlight
5-way lighted navigation keypad for alternate way to operate the GUI even in the darkness. Center button is also a power on-off-hibernate switch 12 VDC adapter jack
to power the unit and charge the Li-Ion Polymer battery
Product Details
Each application is color coded. Entry or return to a specific test or setup is quick. Test results are easily accessible from the bot-tom toolbar
Product Details
Intuitive Graphical User Interface allows quick learning and operation of the unit.
Holding and operating the ergonomically shaped and light Netprobe 2000 is easy,
Operating at night, dark or dim light condition is not a problem. The display and the 5-way navi-gation keypad are lighted
Toolbar provides additional tools to: calibrate the touch panel, set up audio volume, take screenshot, check battery charge status and access soft power down.
T1 and E1 Testing Applications
Major alarms are monitored con-tinuously and any problems re-ported. Alarm simulation allows injection of the specific alarm into the line.
Propagation Delay test allows measuring voice and data delay in various part of the network.
T1 CSU loop codes allow looping back the remote NIU or CSU to perform loop-around test
The primary func-tion of the unit is to perform bit error test with either: 1. end-to-end or 2. looparound configuration
T1 and E1 Testing Applications
Auto Monitor test mode allows automatic verifi-cation of multiple parameters for T1 and E1 line, alarms, G.826 and RFC 1406. The report shows FAIL or OK. Re-sults can be dis-played as histo-grams.
Datacom Bit Error Testing is performed via the dedicated cable type such as RS-232/530, V.35 or RS-449. The Co-dir test can be also accessed via Bantam connectors
T1 and E1 pulse template analysis is performed automatically and reported graphically. Any issues with the pulse amplitude, width or shape are visible on the template.
Remote Access is available via PC, Tablet or Android running VNC ap.
VoiP Testing
NP2000-VoIP option allows SIP controlled call origination and call answer. Microphone and speaker are pro-vided in the included handset ac-cessory as shown below:
After entering the SIP-URL number and registration with the selected SIP Proxy Server the VoiP phone is
ready to dial or to answer a SIP call.
The example below shows the Net-Probe 2000 with VoIP option con-nected with the DSL modem, cable modem or GPON Gateway at the customer site to test or trouble-shoot triple play VoIP service.
All originated and received calls are logged with Time and Type. Each call is identified by source and destination IP addresses and
Adding a new VoiP account is simple and quick.
SIP protocol handshake for each call can be displayed to locate problem or to confirm proper op-eration.
Voice qualiy can be evaluated with MOS score
WiFi Testing
The NetProbe 2000 WiFi option supports IEEE 802.11 a/b/g/n/bluetooth for 2.4 GHz and 5 GHz bands. It provides two applications:
Wifi interface for the tester to access Ethernet network
Wifi analyzer capable of detection of WiFi networks and access points
All Wifi networks with signal at least –90dB are detected and categorized as encrypted and non-encrypted. Encryption key types are identified: No encryption |WEP key| WPA2-PSK| WPA-PSK
Each network can show its Access Points with number of frequencies used and their power level
Once connection to the selected access points is established detail description is available and upper layer test is possible
Starting test per-forms ping test and web access to a popular site and to 8.8.8.8 ad-dress
Technical Specification
G.703 E1 INTERFACE E1 RECEIVER: Impedance: 120 or 75 Ohm Connectors: BNC and RJ-45 Input Frequency: 2,048,000 Hz +/-300 ppm Sensitivity: TERM +3 to -39 dBDSX, Bridged 0 to -30 dBDSX DSX 0 to -26 dB resistive loss from nominal DSX level Input Jitter Tolerance: Exceeds CCITT G.823
E1 TRANSMITTER: Impedance: 120 or 75 Ohms software switchable with BNC and RJ-48 connectors Output Level: 0+/-0.5 dBDSX Output Clock: Internal oscillator 2,048 kHz+/- 5 ppm External, 3000 Ohm TTL, SMA Recovered from input signal
E1 GENERAL: 2048 kbs E1 Interface: Per CCITT G.703, G.704 Framing Modes: Auto, Unframed, CAS, CCS, CAS & CRC4, CCS& CRC4 Line Coding: HDB3, AMI PCM Companding Law: u or A Input/Output Connectors: BNC ( or BANTAM), RJ-45 ALARM/STATUS LED's with history: Signal/Loss of Signal: green/red/off Frame Sync/Loss of Frame: green/red/off Alarm: red, combines the following alarms: LOS - loss of signal OOF - out of frame AIS - E1 AIS alarm detected RAI - remote Alarm detected MFAIS - multiframe AIS alarm detected MFRAI - red, multiframe remote alarm detected Error: red, on whenever any error is present Psync: green, pattern sync/pattern loss – green/off when sync is lost (No pattern sync)
E1 AUTO MONITOR: Line: Code Error- bipolar violation of HDB3 or AMI Frequency: Range 2200- 1800 hz, Resolution 1Hz, accuracy 5 ppm standard Signal Level: +3 to -40 dbDSX,( 0.06 to 8.5 Vp-p ) Clock Slips: +/- between E1 input and internal or external E1 clock Frame Slips: clock slips /256 Alarms: LOS, OOF, AIS, RAI, MFAIS, MFRAI Errors: Code, Frame, CRC, FEBE G.826: ES, SES, ES RATIO, SES RATIO, AVS, UAVS, RFC 1406: total sec, ES, SES, AVS, UAVS M.2100: ES, SES, UAVS
E1 BERT (BIT ERROR TEST) FUNCTIONS: ITU-T G.703, G.704 E1 Patterns: 2n-1, n =7,9,10,15,20,23, QRSS ,All Zero, All Ones, 1:3, 1:7, 1:15,1:31, Multipattern, Bridgetap, Inverted Error Measurements: Logic Errors, Rate, ERS, BPV Errors, Rate, ERS Frame Errors, Rate, ERS CRC Errors, Rate, ERS E-bit Errors,Rate, ERS G.821: EFS, ERS, SES, AVS, UAVS Error Injection: types -Logic, BPV(Code), Frame,CRC rate - Single, Continuous Rate 10-1 to 10-9 Send Alarms: emulate LOS, OOF, AIS and Yellow(remote) alarms.
Alarm: red LED monitors the following alarms: LOS - loss of signal OOF - out of frame AIS - E1 AIS alarm detected RAI - remote Alarm detected Loopbacks: Remote Looback, enables also through mode for line code and errors transparency Local Loopback FRACTIONAL E1: Fractional N x 56/64 kb, n=1,.. ,31 access for Auto Monitor or BERT tests. NP2000-PSA - Pulse Shape Analysis: samples and analyzes E1 pulse shape on the G.703 mask, displays or prints the plot. NP-2000-PDL - Round trip propagation delay Range: 0-2 sec Resolution: 1 msec
DS1(T1) INTERFACE T1 RECEIVER: Impedance: 100 or 75 Ohm Connectors: BANTAM and RJ-45 Input Frequency: 1,5444,000 Hz +/-300 ppm Sensitivity: TERM +3 to -34 dbDSX, Bridged 0 to –30 dBDSX DSX 0 to -26 dB resistive loss from nominal DSX level Input Jitter Tolerance: Exceeds CCITT G.823
T1 TRANSMITTER: Impedance: 100 Ohms software switchable with BNC and RJ-48 connectors Output Level: 0+/-0.5 dBDSX, 6V p-p Output Clock: Internal oscillator 1,544 kHz+/- 5 ppm External, 3000 Ohm TTL, SMA Recovered from input signal
T1 GENERAL: DS1 (T1 Interface): Per CCITT G.703, G.704 Framing Modes:Auto,Unframed, ESF, D4, SFS, SF-N, SLC-96 Line Coding: B8ZS, AMI PCM Companding Law: u or A Input/Output Connectors: BANTAM and RJ-45 ALARM/STATUS LED's with history: Signal/Loss of Signal: green/red/off Frame Sync/Loss of Frame: green/red/off Alarm: red, combines the following alarms: LOS - loss of signal OOF - out of frame AIS - E1 AIS alarm detected RAI - remote Alarm detected Yellow - remote alarm detected Error: red, on whenever any error is present Psync: green, pattern sync/pattern loss – green/off when sync is lost (No pattern sync)
T1 AUTO MONITOR: Line: Code Error- bipolar violation of B8ZS or AMI Frequency: Range 2200- 1800 hz, Resolution 1Hz, accuracy 5 ppm standard Signal Level: +3 to –34 dBDSX,( 0.06 to 8.5 Vp-p ) Clock Slips: +/- between T1 input and internal or external T1 clock Frame Slips: clock slips /193 Alarms: LOS, OOF, AIS, Yellow Errors: Code, Frame, CRC G.826: ES, SES, ES RATIO, SES RATIO, AVS, UAVS, RFC 1406: total sec, ES, SES, AVS, UAVS
T1 BERT (BIT ERROR TEST) FUNCTIONS: CB-119 Patterns: 2n-1, n =7,9,10,15,20,23, QRSS ,All Zero, All Ones, 1:3, 1:7, 1:15,1:31, Multipattern, Bridgetap, Inverted Error Measurements: Logic Errors, Rate, ERS, BPV Errors, Rate, ERS Frame Errors, Rate, ERS CRC Errors, Rate, ERS G.821: EFS, ERS, SES, AVS, UAVS Error Injection: types -Logic, BPV(Code), Frame,CRC rate - Single, Continuous Rate 10-1 to 10-9 Send Alarms: emulate LOS, OOF, AIS and Yellow(remote) alarms Alarm: red LED monitors the following alarms: LOS - loss of signal OOF - out of frame AIS - T1 AIS alarm detected RAI - remote Alarm detected Loopbacks: Remote Looback, enables also through mode for line code and errors transparency Local Loopback FRACTIONAL T1: Fractional N x 56/64 kb, n=1,.. ,24 access for Auto Monitor or BERT tests. NP2000-T1PSA - Pulse Shape Analysis Option: samples and analyzes mask and T1 pulse shape on the CB.119 mask, displays or prints the plot. NP-2000-T1PDL—Round trip propagation delay Range: 0-2 sec Resolution: 1 msec
DATACOM: Option NP2000-DATACOM: INTERFACES: V.24/RS-232, V.35, RS-530, G.703 CO-DIR via Hirose ST60-36 pin connector ( cables are ordered seperately) DATA RATE: nx56/64kb/s, n=1 to 24 (32), variable frequency synthesizer 300 hz – 8 Mhz G.703 Co-dir 64 kb/s RS-232 - 300b/s to 115kb/s V.35,V.36,RS-530-300b/s to 8 Mb/s BERT test: Patterns: 2n-1, n =7,9,10,15,20,23, QRSS ,All Zero, All Ones, 1:3, 1:7, 1:15,1:31, Multipattern, Bridgetap, Inverted Error Measurements: Logic Errors, rate, ERS, rate ES, rate Pattern Loss, Character errors
TEST RESULTS: Storage: Internal microSD 4 GB card, External: USB flash Format: SQL Dbase, Date and time started, time stopped 3 Levels: Summary Log of all test, Details per test, Histogram od selected record Output: Display, Export to USB Flash, Print to serial printer.
NP2000-WiFi: Radio interface: 802.11 b/g/n and Bluetooth. 2.4Ghz and 5 Ghz ranges. List networks: signal level, security/encryption, # of APs in network, SSID name, type of network List & locate access points: channel, signal level, AP name or MAC address, SSID name, security/encryption, type of network
AP authorization status and details Connections test: associate with AP, request IP, Ping Channel usage Client details: signal level, AP MAC and name , chan-nel, SSID, type Locate clients Requires external twist on antenna
NP2000-C37.94: Based on IEEE C37.94 –2002. Connector: ST Test Rate: nx64kb/s, n =1 to 12 Test Pattern:: PRBS, fixed Error injection Transmit Clock: internal, recovered Transmitter: 830 +/- 40nm multimode Receiver: -32 dBm to –11 dBm Measurements: errors, error rate, G.821, alarm, frequency, view data traffic, propagation delay, optical power.
NP2000– VoIP: Originate and terminate SIP calls with headset, call log, SIP flow, MOS score.
GENERAL: WAN Interfaces: E1, T1, V.35, RS-232, RS-530, RS-449, 64kb Co-dir, Ethernet Interfaces: LAN 10/100 Base-T USB: master , mini USB connector Microphone and earphones (headset): mini USB connector. Wi-Fi Interface: Optional 802.11 b/g/n & Bluetooth for meas-urement and IP access. Rechargeable Battery Pack: Li Ion battery pack, 7.2V, 4800 mAh, 4-8 hours operating time. External Power: AC/DC power converter outputs 12VDC at 2A, 110-240 VAC, 50-60 Hz. Enclosure: Ruggedized ABS with rubber shell. Display: 3.5” TFT LCD, with 320x240 resolution, white back-light, touchscreen. 5-way touchpad: up, down, left, right, OK/power button Dimensions: 100mm wide, 210mm tall, 42mm deep. Weight: 0.75 kg(1.65lbs) without battery. Battery weight: 250g Enviromental: Operating Temperature: 00C to 500C Operating Humidity: 5% to 90% non condensing Storage: -100C to 700C
Technical Specification
Any part of the specification is subject to change without notice
Ordering Information
8201 Greensboro Dr, Suite 300 McLean, Virginia 22102, USA
tel: 703-348-0902
www.netrsr.com [email protected]
skype: netresearch