nepal electricity authorityof 132kv gis substation single-stage, two-envelope bidding procedure...
TRANSCRIPT
NEPAL ELECTRICITY AUTHORITY (An Undertaking of Government of Nepal)
Project Management Directorate
KATHMANDU VALLEY TRANSMISSION CAPACITY REINFORCEMENT PROJECT
(A Component of Power Transmission and Distribution Efficiency Enhancement Project)
BIDDING DOCUMENT FOR
Procurement of Plant, Design, Supply and Installation of 132kV GIS Substation
Single-Stage, Two-Envelope Bidding Procedure
Issued on: 27 March 2017 Invitation for Bids No.: PMD/PTDEEP/KTCEP–073/74 - 01 ICB No.: PMD/PTDEEP/KTCEP–073/74 - 01 Employer: Nepal Electricity Authority Country: Nepal
VOLUME –III OF III March 2017
Kathmandu Valley Transmission Capacity Reinforcement Project Project Management Directorate Matatirtha, Kanchan Basti, Chandragiri 11, Kathmandu, Nepal
Telephone: +977-1-5164099, 5164104 Fax: +977-1-5164099
THIS DOCUMENT IS ONLY FOR REFERENCE, NOT FOR BIDDING
Table of Contents
SECTION IV PRICE SCHEDULE
Note: 1) Bidder is required to quote prices in this Schedule for all the individual items/sub-items.2) The Prices of equipment’s are inclusive of type test charges.3) BOQ given is indicative only based on the scope of work as given in Employer's
Requirements. The quantities mentioned above may undergo change during detailedengineering to meet the functional requirement and scope of work defined in Employer'sRequirements. The Contractor shall prepare and submit the final BOQ within 90 days ofsigning of Contract.
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 1 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
PART 1 132/11 kV Phutung Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIESA POWER TRANSFORMER
1.0 POWER TRANSFORMER1.1 31.5/45 MVA , 132/11 KV, 3-phase Indoor Transformer (Excluding
insulating oil)Nos. 2
1.2 Insulating oil for 31.5/45 MVA , 132/11 KV, 3-phase Transformer (* 1Lot = Oil for 1 Transformers)
Lot* 2
2.0 Testing & Maintenance Equipments2.1 Oil Storage Tank No. 1
2.2 Transformer Oil Filtration plant (6KLPH) No 1
3 LT TRANSFORMER
3.1 315 kVA, 11/0.400kV (Indoor/Outdoor) with all accessories. Nos 1
3.2 11kV Bus disconnector, Power fuse and all other accessories for above transformer.
Set 1
B 145 kV equipment
1.0 145KV GIS Equipment1.1 145kV, SF6 GIS Bus Bars Module [ Module description as per Technical
Project specification]Set 2
1.2 145kV, SF6 GIS ICT bay Module [ Module description as per Technical Project specification]
Set 2
1.3 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification]
Set 4
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 2 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
1.4 145kV, SF6 GIS Bus Coupler bay Module [ Module description as per Technical Project specification]
Set 1
1.5 145kV, 1250A, 31.5kA SF6/Air Bushing for Connecting GIS to AIS alongwith support structure
Nos 12
1.6 145kV, 1250A, 31.50kA SF6/Air Bushing for Connecting GIS to Transformer alongwith support arrangement
Nos 6
1.7145kV, 1250A, 1phase SF6 GIS Bus duct alongwith support structure
OPTION-I
2000A, 31.5kA for 1 sec. Single Phase Mtr. 600
OPTION-II
2000A, 31.5kA, 1sec three phase Mtr. 200
Note : Bidder is required to quote for either option-I or Option-II
1.8 Testing & Maintenance Equipment for GIS1.8.1 Partial Discharge Monitoring System for 145kV GIS System as per
Technical Specification, GISSet 1
1.8.2 Dew Point meter for 145kV GIS System Set 1
1.8.3 SF6 Gas Leak Detector for 145kV GIS System Set 1
1.8.4 EOT crane for 145kV GIS Hall Set 1
1.8.5 SF6 Gas Analyser Set 1
2.0 145KV Outdoor Equipment2.1 145 kV Surge Arrestors
2.1.1 120 kV Surge Arrestors (1- Phase) Nos 12
2.2 145 kV Post insulators, as required Nos 12
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 3 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
C RELAY PANELS (WITH AUTOMATION)
1.0 132 kV
1.1 Line Control & Protection Panel with distance relay / Differential relay Set 4
1.2 Current Differential Relay for other end of line Nos 4
1.3 Transformer Control & Protection Panel (For HV side) Set 2
1.4 Bus Bar Protection Panel Set 1
D MV Switchgear
1.0 11 kV Indoor VCB Switchgear
1.1 11kV 2500A Incomer Set 2
1.2 11kV 1250A Outgoing Set 10
1.3 11kV 2500A Buscoupler Set 1
1.4 11kV 2500A Trunking Set 1
2 Surge arrestors with accessories for 11 kV Line Nos 18
E COMMON EQUIPMENTS
1.0 Relay Test tool kit Set 1
2.0 Time synchronisation equipment No. 1
F SUBSTATION AUTOMATION
Complete Substation Automation System (SAS) for substation including hardware and software for the substation & remote control stations alongwith associated equipments for the following bays as per Technical Specification
1.0 Main bays to be automated
1.1 132 kV system Bay Nos 7
1.2 11 kV system Bay Nos 13
1.3 BCU for controlling & monitoring of Auxilary System Set 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 4 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
G Teleprotection & communication Equipments
1 PBAX with following configuration as per TS Set 1
1.1 2 wire subscriber interface card with capacity 32 local subscribers or as required (along with 32 nos. Instruments)
1.2 4 wire E & M interface card with capacity 8 nos. trunks (For PLCC or Other communication mode) as required
1.3 E-1 interface with 2 trunks G-703
1.4 2 wire interface with 1 trunk (For PSTN)
2 Testing & Maintenance equipment (print test kit only) Set 1
3 4 wire telephone equipment Lot 1
H LT Switchgear (As per Technical specification)
1 415V Main switchboard Set 1
2 415V ACDB Set 1
3 415V MLDB Set 1
4 415V Emergency LDB Set 1
5 220V DCDB Sets 1
6 48V DCDB Sets 1
I Batteries
1 220V
1.1 600 AH Nos 2
J Float Cum Boost Battery Charger
1 220V Float Cum Boost Battery Charger
1.1 80A/80A Nos 2
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 5 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
K Fire Protection System
1 Portable /Trolley/Wheel mounted extinguishers
1.1 9 litre water type Nos 5
1.2 50 litre foam type Nos 2
1.3 4.5 kg CO2 type Nos 13
1.4 4.5 kg Dry Chemical Power (DCP) type Nos 5
2 Smoke detection system Set 1
3 Fire detection and Alarm System Set 1
L Cables along with clamps, glands, lugs and straight joints etc.
1 Power Cables - (1.1kV grade)
1.1 3.5Cx300 sqmm (XLPE) cable for filter Machine along with termination arrangement as per TS
KM 0.3
2 Power Cables - (12kV grade)
2.1 1Cx800 sqmm (XLPE) copper cable for Incomer with termination arrangement as per TS
KM 2
2.2 3Cx300 sqmm (XLPE) Aluminum cable for outgoing feeders along with termination arrangement as per TS including cable duct pipe for laying outside cable trench to nearest pole.
KM 1
3 Power Cables - (145kV grade)
3.1 1Cx500 sqmm (XLPE) copper cable for line bay along with termination arrangement as per TS
KM 1
3.2 1Cx240 sqmm (XLPE) copper cable for Transformer along with termination arrangement as per TS
KM 0.5
Note:Cables are to be used as a option to Bus ducts, if required
M Air conditioning System for Control Building
1 High wall type split AC unit of 2 TR capacity Nos 15
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 6 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
N Fabrication, galvanising and supply of following Steel Structures including nuts, bolts, all types of washers, packplates, step bolts and gusset plates including foundation bolts.
1.0 Lattice Structure including Foundation Bolts MT 40
2.0 Pipe Structure including Foundation Bolts . MT 10
3.0 Fastners and step bolts.(Nuts,Bolts & Washers) MT 5
O Communication equipments
1 Transmission equipments
1.0 SDH Equipment ( STM- 4 MADM, upto 3 MSP protected directions)1.1
Base Equipment (Common cards, Cross-connect/control cards, Optical base cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc. fully equipped including Optical interphase/SFPs and Tributary cards for full function with future proviison of communication and protection system.
Set 1
2 Termination Equipment2.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of the system
Set 1
3 Equipment Cabinets3.1 For Drop/Insert Multiplexer No. 1
3.2 For SDH Equipment No. 1
4 Main Distribution Frame(100 pairs) No. 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 7 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
5 BOQ for Auxiliary Power Supply Equipments 5.1 SMPS based 48V DC Power Supply (DCPS) system Nos. 2
5.2 VRLA type Battery bank for above DCPS system Nos. 2
At Kathmandu LDC
6 Termination Equipment6.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of system
Set 1
7 Equipment Cabinets7.1 For Drop/Insert Multiplexer No. 1
8 Main Distribution Frame(100 pairs) No. 1
Sub-Total Part-A
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 8 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Part-B: CONTRACTOR ASSESSED QUANTITIESA Erection Hardware
Insulator strings, Disc Insulators, Hardware, conductor, Al tube, bus-bar materials, cable trays, clamps, spacers, connectors including equipment connectors, Junction box, earthwire, buried cable trenches/pipe equipment & lighting, all accessories etc. for the following:
1.0 145kV GIS Termination Arrangement:
1.1 Line Bay Set 4
1.2 Transformer Bay Set 2
2.0 Earthing and lightning protection including necesaary connectors/connections, risers etc. complete in all respect( but excluding LM structures for Lightning protection)
2.1 Earth Conductor (copper) LS 1
2.2 Earth Rod (copper clad steel) LS 1
2.3 Equipment for lightning protection LS 1
B Fire Protection System
1 Fire Protection system with complete U/G & O/G piping, Tanks, building and accessories etc. complete for Indoor Transformer: Transformer Set 2
1.1 132/11 KV, 3-phase Transformer
C Illumination System
1 Control Building cum administrative building illumination LS 1
2 Switchyard lighting Outdoor LS 1
3 Street lighting LS 1
4 Security Room LS 1
5 Car parkings LS 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 9 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
D Air conditioning & ventilation System
1.0 Air conditioning 1.1 Panel room in 145kV GIS Hall LS 1
2.0 Ventilation system 2.1 145KV GIS hall LS 1
E POWER & CONTROL CABLES
1 Power Cables(PVC)- (1.1kV grade) LS 1
2 Power Cables (XLPE)(excluding 3.5Cx300 sqmm (XLPE) cable for filter Machine)- (1.1kV grade)
LS 1
3 Control Cable (PVC)- (1.1kV grade) LS 1
4Cable glands, lugs & straight through joints for Power & Control cables
LS 1
F
Integration of all 132/11kV Bays under present scope with the SCADA of SIEMENS (SINAUT Spectrum) at Load Dispatch Centre, Kathmandu including supply of Hardware, Software, accessories etc. as per TS Section Project.
LS 1
Sub-Total Part-B
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 10 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Part-C: Mandatory Spares
(I) Mandatory Spare List for Transformer
For 132/11 KV, 3-phase Transformer1 Bushing of each rating with metal parts & gaskets and lifting tools Set 1
2 Cooler fan with Motor No. 1
3 Buchholz Relay(Main Tank) complete with floats and contacts Set 1
4 Local and Remote WTI with sensing device and contact(each) Set 1
5 Magnetic oil level gauge No. 1
6 Strarters, contactors,switches & Relays for Electrical control panels(One ste of each type)
Set 1
7 Remote Tap postion Indiactor No. 1
8 Spare insulating oil to be handed over to Owner after commisioning for O&M requirement
KL 10
(II) SPARES FOR 145kV GIS
1 General
1.1 SF6 gas Pressure Relief Devices, 1Nos. of each type Set 1
1.2SF6 Pressure gauge cum switch OR Density monitors and pressure switchas applicable (1 no. of each type)
Set 1
1.3Coupling device for pressure gauge cum switch for connecting Gashandling plant
Set 1
1.4 Rubber Gaskets, “O” Rings and Seals for SF6 gas of each type Set 1
1.5 Molecular filter for SF6 gas with filter bags(20% of total weight) Set 1
1.6 All types of Control Valves for SF6 gas of each type Set 1
1.7 SF6 gas (20 % of total gas quantity) Set 1
1.8 All types of coupling for SF6 gas (1 no. of each type) Set 1
1.9 Pipe length (Copper or Steel as applicable) for SF6 Circuit of each typeSet 1
1.10Covers with all accessories necessary to close a compartment in case ofdismantling of any part of the Enclosure to ensure the sealing of thiscompartment
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 11 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
1.10.1 For 3 Phase Enclosure if applicable Nos. 1
1.10.2 For Single phase enclosure if applicable Nos. 1
1.11Locking device to keep the Dis-connectors (Isolators) and Earthingswitches in close or open position in case of removal of the drivingMechanism
Sets 1
1.12 Bus Support insulator of each type for 3 phase/single phase enclosure.Nos. 1
1.13 SF6 to air bushing (145kV) as applicable Sets 1
2 145 KV SF6 CIRCUIT BREAKER:
2.1Complete Circuit Breaker pole of each type & rating complete withinterrupter, main circuit enclosure and Marshalling Box with operatingmechanism
Nos. 1
2.2 Rubber gaskets, `O' rings and seals for SF6 gas (1 No. of each type)Sets 1
2.3 Trip coil assembly with resistor as applicable Sets 1
2.4 Closing coil assembly with resistor as applicable . Sets 1
2.5Relays, Power contactors, push buttons, timers & MCBs etc (1 No. ofeach type & rating)
Sets 1
2.6 Closing coil assembly (including valve, if applicable) Sets 1
2.7 Trip coil assembly (including valve, if applicable) Sets 1
2.8 Auxiliary switch assembly of each type Sets 1
3 145 KV ISOLATORS :
3.1Complete set of 3-phase dis-connector including main circuit, enclosure,driving mechanism (one no of each type)
Sets 1
3.2Single Phase/ 3-phase Earthing switch including main circuit, enclosure,driving mechanism.
Sets 1
3.3Copper contact fingers for dis-connector male & female contact for onecomplete (3-phase) dis-connector of each type and rating
Sets 1
3.4Copper contact fingers for earthing switch male & female contacts, for onecomplete(3-phase) earthing switch of each type and rating
Sets 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 12 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
3.5Open / Close contactor assembly, timers, key interlock for one complete(3 phase) dis-connector and (3 phase) earthing switch (1 No. of each typeand rating)
Sets 1
3.6 Push button switch - (1 No. of each type & rating) as applicable Sets 1
3.7 Limit switch and Aux. Switches for complete 3 phase equipment
3.7.1 For isolator Sets 1
3.7.2 For earth switch Sets 1
4 145 KV CURRENT TRANSFORMER
4.1 Gas insulated complete CT of each type and rating with enclosure. Lot 1
4.2 Secondary bushing of each type Sets 1
5 145 kV VOLTAGE TRANSFORMER
5.1 Gas insulated complete PT of each type and rating with enclosure. Nos. 1
6 120kV SA6.1 Complete LA No. 1
6.2 Surge counter/monitor Nos. 2
(III) C&R PANELS1 Transformer protection panel :
1.1 Transformer differential protection No. 1
1.2 REF protection relay with non-linear resistor No. 1
1.3 Directional over current & E/F Protection Relay No. 1
2 Line protection panel :
2.1 Distance Protection relay or Current differential Protection relay No. 1
3 Breaker Relay panel: Part of CRP3.1 Breaker failure relay No. 1
3.2 Trip circuit supervision relay Nos. 2
3.3 Self reset trip relay (relay of each type) Set 1
3.4 Hand reset trip relay(relay of each type) Set 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 13 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
3.5 Timer relay(relay of each type) Set 1
3.6 DC supervision relay(relay of each type) Set 1
3.7 Flag relays(relay of each type) Set 1
3.8 Auxiliary relays(relay of each type) Set 1
(IV) Teleprotection Equipments
1 Set of prints for protection coupler(digital) Set 0
(V) SAS1 Bay Control Unit (IED) of each type Set 1
2 Ethernet Switch of each type Set 1
(VI) BATTERY CHARGER( 220V)1 Set of control cards Set 1
2 Set of relays Set 1
3 Rectifier transformer No. 1
4 Thyristor/diode Set 1
5 Fuses of Thyristor with indicators Set 6
(VII) COMMON SPARES1 Bay unit Module No. 1
2 2 wire local subscriber interface card for PABX No. 1
3 E1 Interface card for PABX No. 1
(VIII) 11 kV Switchgear
1 11kV Vacuum Interrupter for Incomer and Outgoing No 6
2 Tripping Coils Nos 3
3 Closing Coils Nos 3
4 Spring Charging Motor Set 1
5 Protection Relays
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 1 PAGE 14 OF 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
5.1 3 phase Overcurrent Relay, for 11kV side one of each type Nos 1
5.2 Ground Fault Relay, for 11kV side, one of each type Nos 1
6 Ammeter, Nos one of each rating Nos 1
7 Voltmeter, Nos Nos 1
8 kVA Meter, each Nos 1
9 CTs as in Outgoing Feeder Set 1
10 Operating Handle Nos 1
11 Indicating lamps (100% of used), Lot Lot 1
Sub-Total Part-C
Total For PART 1 Phutung Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 1 ( Total of column 9 to be carried forward to Schdule 5: Grand Summary)
Note : 1) Bidder is required to quote prices in this Schedule for all the individual items/sub-items.
* Strike-out whichever is not applicable.
Name of Bidder: Date:
Signature of Bidder:
(Printed Name)
(Designation)
(Common Seal)
2.) The Prices of equipments are inclusive of type test charges
3.) BOQ given above is indicative only based on the scope of work as given in Employer's Requirements. The quantities mentioned above may undergo change during detailed engineering to meet the functional requirement and scope of work defined in Employer's Requirements.
Specify currency in accordance with BDS ITB Clause 32.1, Part-I of the Bidding Documents.
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 2 PART 1 PAGE 15 OF 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No.2: Plant and Equipment including Mandatory Spares Parts to be supplied from within Nepal LC: Local Currency (ALL Price in Local Currency)
Total Amount (Excluding Taxes
)
Custom, VAT and
other taxes
Unit Rate Amount Unit Rate Amount
1 2 3 4 5 6 = (4) x (5) 7 8=(4)x(7) 9=6+8 10
PART 1 132/11 kV Phutung Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIES
Part-B: CONTRACTOR ASSESSED QUANTITIES
Part-C: Mandatory Spares
Total For PART 1 Phutung Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 2 (Total of column 9 to be carried forward to Schdule 5: Grand Summary)
Note : 1) Bidder is required to quote prices in this Schedule for all the items in Schedule 1 which they wish to supply from within Nepal.
# Specify currency in accordance with BDS ITB Clause 32.1, Part-I of the Bidding Documents.* Strike-out whichever is not applicable.
a Specify currency in accordance with ITB 19.1 of the BDS.
Name of Bidder: Date:
Signature of Bidder: (Printed Name) (Designation)
(Common Seal)
Ex Faxtory Price (Excluding VAT) in LC
Inland transportation to site in LC
b Column 5 Price shall include all customs duties and sales and other taxes already paid or payable on the components and raw materials used in the manufacture or assembly of the item or the customs duties and sales and other taxes already paid on previously imported items.
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Item No. Item description Unit Quantity
2.) The Prices of equipments are inclusive of type test charges
Name of Bidder: Package A-2 Signature of Bidder:
SPECIFICATION NO SCHEDULE 3 , PART 1 PAGE 16 of 39
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Local Currency Portion
Foreign Currency Portion
Quantity Unit NRs Currency LC FC
1 2 3 4 5 6 7=3x5 8=3x6
PART 1132/11 kV Phutung Substation (132V GIS & Indoor)
Not Applicable
Total for Schedule 3 (Total of column 7 & 8 to be carried forward to Schdule 5: Grand Summary)
NOTE: The design cost is included in schedule 1.
Name of Bidder: Date:Signature of Bidder: (Printed Name) (Designation) (Common Seal)
Schedule A-3: Design Services
NEPAL ELECTRICITY AUTHORITY
Item No. Item DescriptionEstimated
Unit Prices Total Prices
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Name of Bidder PACKAGE A2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 17 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6PART 1 132/11 kV Phutung Substation (132V GIS & Indoor)
Part‐A : EMPLOYER ASSESSED QUANTITIESA POWER TRANSFORMER
1.0 POWER TRANSFORMER1.1 31.5/45 MVA , 132/11 KV, 3-phase Indoor Transformer (Excluding
insulating oil)Nos. 2
1.2 Insulating oil for 31.5/45 MVA , 132/11 KV, 3-phase Transformer (* 1Lot = Oil for 1 Transformers)
Lot* 2
2 LT TRANSFORMER
2.1 315 kVA, 11/0.400kV (Indoor/Outdoor) with all accessories. Nos 12.2 11kV Bus disconnector, Power fuse and all other accessories for
above transformer.Set 1
B 145 kV equipment
1 145KV GIS Equipment1.1 145kV, SF6 GIS Bus Bars Module [ Module description as per
Technical Project specification]Set 2
1.2 145kV, SF6 GIS ICT bay Module [ Module description as per Technical Project specification]
Set 2
1.3 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification]
Set 4
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 18 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
1.4 145kV, SF6 GIS Bus Coupler bay Module [ Module description as per Technical Project specification]
Set 1
1.5 145kV, 1250A, 31.5kA SF6/Air Bushing for Connecting GIS to AIS alongwith support structure (Single Phase)
Nos 12
1.6 145kV, 1250A, 31.50kA SF6/Air Bushing for Connecting GIS to Transformer alongwith support arrangement (Single Phase)
Nos 6
1.7 145kV, 1600A, 1phase SF6 GIS Bus duct alongwith support structureOPTION-I
2000A, 40kA for 1 sec. Single Phase Mtr. 600
OPTION-II
2000A, 40kA, 1sec three phase Mtr. 200
Note : Bidder is required to quote for either option-I or Option-II
1.8 Testing & Maintenance Equipment for GIS1.8.1 Partial Discharge Monitoring System for 145kV GIS System as per
Technical Specification, GISSet 1
1.8.2 EOT crane for 245kV GIS Hall Set 1
2.0 145KV Outdoor Equipment2.1 145 kV Surge Arrestors
2.1.1 120 kV Surge Arrestors (1- Phase) Nos 12
2.2 145 kV Post insulators, as required Nos 12
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 19 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
C RELAY PANELS (WITH AUTOMATION)
1.0 132 kV
1.1 Line Protection Panel with distance relay / Differential relay Set 4
1.2 Current Differential Relay for other end of line Nos 4
1.3 Transformer Protection Panel (For HV side) Set 2
1.4 Bus Bar Protection Panel Set 1
D MV Switchgear
1.0 11 kV Indoor VCB Switchgear
1.1 11kV 2500A Incomer Set 2
1.2 11kV 1250A Outgoing Set 10
1.3 11kV 2500A Buscoupler Set 1
1.4 11kV 2500A Trunking Set 1
2 Surge arrestors with accessories for 11 kV Line Nos 18
E COMMON EQUIPMENTS
1.0 Special Relay Test Tool kit No 1
F SUBSTATION AUTOMATION
F.1 Complete Substation Automation System (SAS) for substation including hardware and software for the substation & remote control stations alongwith associated equipments for the following bays as per Technical Specification
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 20 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
1.0 Main bays to be automated
1.1 132 kV system Bay Nos 7
1.2 11 kV system Bay Nos 13
1.3 BCU for controlling & monitoring of Auxilary System Set 1
G Teleprotection & communication Equipments
1 PBAX with following configuration as per TS Set 1
1.1 2 wire subscriber interface card with capacity 32 local subscribers or as required (along with 32 nos. Instruments)
1.2 4 wire E & M interface card with capacity 8 nos. trunks (For PLCC or Other communication mode) as required
1.3 E-1 interface with 2 trunks G-703
1.4 2 wire interface with 1 trunk (For PSTN)
2 Testing & Maintenance equipment (print test kit only) Set 1
3 4 wire telephone equipment No 1
H LT Switchgear (As per Technical specification)
1 415V Main switchboard Set 1
2 415V ACDB Set 1
3 415V MLDB Set 1
4 415V Emergency LDB Set 1
5 220V DCDB Sets 1
6 48V DCDB Sets 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 21 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
I Batteries
1 220V
1.1 600 AH Nos 2
J Float Cum Boost Battery Charger
1 220V Float Cum Boost Battery Charger
1.1 80A/80A Nos 2
K Fire Protection System
1 Portable /Trolley/Wheel mounted extinguishers
1.1 9 litre water type Nos 5
1.2 50 litre foam type Nos 2
1.3 4.5 kg CO2 type Nos 13
1.4 4.5 kg Dry Chemical Power (DCP) type Nos 5
2 Smoke detection system Set 1
3 Fire detection and Alarm System Set 1
L Cables along with clamps, glands, lugs and straight joints etc.
1 Power Cables - (1.1kV grade)
1.1 3.5Cx300 sqmm (XLPE) cable for filter Machine along with termination arrangement as per TS
KM 0.3
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 22 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
2 Power Cables - (12kV grade)
2.1 1Cx800 sqmm (XLPE) copper cable for Incomer with termination arrangement as per TS
KM 2
2.2 3Cx300 sqmm (XLPE) Aluminum cable for outgoing feeders along with termination arrangement as per TS including cable duct pipe for laying outside cable trench to nearest pole.
KM 1
3 Power Cables - (145kV grade)
3.1 1Cx500 sqmm (XLPE) copper cable for line along with termination arrangement as per TS
KM 1
3.2 1Cx240 sqmm (XLPE) copper cable for Transformer along with termination arrangement as per TS
KM 0.5
Note:Cables are to be used as a option to Bus ducts, if required
M Air conditioning System for Control building
1 High wall type split AC unit of 2 TR capacity Nos 15
N Fabrication, galvanising and supply of following Steel Structures including nuts, bolts, all types of washers, packplates, step bolts and gusset plates including foundation bolts.
1.0 Lattice Structure including Foundation Bolts MT 40
2.0 Pipe Structure including Foundation Bolts . MT 10
3.0 Fastners and step bolts.(Nuts,Bolts & Washers) MT 5
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 23 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
O Communication equipments
1 Transmission equipments
1.0 SDH Equipment ( STM- 4 MADM, upto 3 MSP protected directions)1.1 Base Equipment (Common cards, Cross-connect/control cards,
Optical base cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc. fully equipped including Optical interphase/SFPs and Tributary cards for full function with future proviison of communication and protection system.
Set 1
2 Termination Equipment2.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of the system
Set 1
3 Equipment Cabinets3.1 For Drop/Insert Multiplexer No. 1
3.2 For SDH Equipment No. 1
4 Main Distribution Frame(100 pairs) No. 1
5 BOQ for Auxiliary Power Supply Equipments 5.1 SMPS based 48V DC Power Supply (DCPS) system Nos. 15.2 VRLA type Battery bank for above DCPS system Nos. 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 24 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
At Kathmandu LDC6 Termination Equipment
6.1 Drop/Insert Multiplexer Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of system
Set 1
7 Equipment Cabinets7.1 For Drop/Insert Multiplexer No. 1
8 Main Distribution Frame(100 pairs) No. 1
Sub-Total Part-A
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 25 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Part‐B: CONTRACTOR ASSESSED QUANTITIESA Erection Hardware
Insulator strings, Disc Insulators, Hardware, conductor, Al tube, bus-bar materials, cable trays, clamps, spacers, connectors including equipment connectors, Junction box, earthwire, buried cable trenches/pipe equipment & lighting, all accessories etc. for the following:
1.0 145kV GIS Termination Arrangement:
1.1 Line Bay Set 41.2 Transformer Bay Set 2
2.0 Earthing and lightning protection including necesaary connectors/connections, risers etc. complete in all respect (but excluding LM structures for Lightning protection)
2.1 Earth Conductor (copper) LS 12.2 Earth Rod (copper clad steel) LS 12.3 Equipment for lightning protection LS 1
B Fire Protection System
1 Fire Protection system with complete U/G & O/G piping, Tanks, building as required and accessories etc. complete for Indoor Transformer: Transformer Set 2
1.1 132/11 KV, 3-phase Transformer
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 26 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
C Illumination System
1 Control Building cum administrative building illumination LS 12 Switchyard lighting Outdoor LS 13 Street lighting LS 14 Security Room LS 15 Car parkings LS 1
D Air conditioning & ventilation System
1.0 Air conditioning system 1.1 Panel room in 145kV GIS Hall LS 1
2.0 Ventilation system 2.1 145KV GIS hall LS 1
E POWER & CONTROL CABLES
1 Power Cables(PVC)- (1.1kV grade) LS 12 Power Cables (XLPE)(excluding 3.5Cx300 sqmm (XLPE) cable for
filter Machine)- (1.1kV grade)LS 1
3 Control Cable (PVC)- (1.1kV grade) LS 1
4Cable glands, lugs & straight through joints for Power & Control cables
LS 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 27 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
F
Integration of all 132/11kV Bays under present scope with the SCADA of SIEMENS (SINAUT Spectrum) at Load Dispatch Centre, Kathmandu including supply of Hardware, Software, accessories etc. as per TS Section Project.
LS 1
Sub-Total Part-B
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 28 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
PART-C: Civil Works (As per technical specification)1.0 Excavation in all types of soil and rock including backfilling
disposal etc. for all leads and lifts Lot 1
2.0 Providing and laying of Plain Cement Concrete (PCC) (1:4:8) Cu.Mtr. 10003.0 Providing and laying of Plain Cement Concrete (PCC) (1:2:4) Cu.Mtr. 3004.0 Providing and laying of Reinforced Cement Concrete Design Mix
(M25) including pre cast, shuttering, Grouting of pockets & underpinning but excluding steel reinforcement.
Cu.Mtr. 2000
5.0 Providing and laying Plain Cement Concrete 1:5:10 (1 cement : 5 sand : 10 Stone aggregate) Cu.Mtr. 500
6.0 Steel Reinforcement (Fe 500) MT 2007.0 Miscellaneous Structural steel used for rails , plates for rail fixing,
,gratings, gratings supports etc for transformer /reactor foundation,cable supportstand earthing cleats ,chequered plates, embedments, edge protection angles for cable trenches but excluding the reinforcement steel and steel for lattice and pipe structures which shall be paid seperately.
MT 30
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 29 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
8.0 Stone filling (40mm) over grating of Transformer /reactor Foundation Cu.Mtr. 40
9.0Stone spreading including antiweed treatment in switchyard but excluding PCC. Sq. Mtr. 2000
10.0
Supplying & laying hume pipe with collars of grade (NP-3) but excluding concrete of bed/support/encasing of hume pipes which shall be paid seperatelyunder respective items of BPS
10.1 250mm dia RM 15010.2 300mm dia RM 12010.3 450mm dia RM 8010.4 600mm dia RM 4011.0 Concrete road as per technical specification and approved drawing
but excluding reinforcement & concrete which shall be paid seperately under respective items of BPS
11.1 Concrete Road 4m wide Sq. m. 400
12.0
Construction of rail-cum-raod as per technical specification and approved drawing including all items such as excavation, compaction, rolling, watering, WBM, etc but excluding concrete, reinforcement and structural steel which shall be paid seperately under respective items of BPS
12.1 Section having two rails Sq. m. 100
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 30 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
13.0
Chain link Switchyard fencing as per technical specification and approved drawing but excluding concrete which shall be paid seperately under respective items of BPS
RM 260
14.0Switch yard Gate excluding concrete which shall be paid seperately under respective items of BPS
Nos.2
15.0 All civil works for construction of drains as per technical specification and approved drawing excluding concrete which shall be paid seperately under respective items of BPS
15.1 Type AA (300mm wide x Depth up to 600mm) RM 50015.2 Type BB (450 wide x Depth From 600 to 900mm) RM 20015.3 Type CC (600 wide x Depth From 900 to 1200mm) RM 20015.4 Type DD (750 wide x Depth From 1200 to 1500mm) RM 20016.0 External water supply as per technical specification from
borewell/single point of water supply within substation boundary to Fire water Tank, control room Building and other buildings as applicable including all items like excavation, pipes, fittings, jointings, valves, chambers/manholes etc
16.1 80mm Dia GI Pipe RM 10016.2 50mm dia GI pipe RM 8016.3 40mm dia GI pipe RM 6016.4 25mm Dia GI Pipe RM 40
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 31 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
17.0 External sewerage system including all item such as excavation,piping, pipe fittings, manholes, gali trap, gali chamber etc.
17.1 (i) 250 mm Dia. RM 5017.2 (i) 150 mm Dia. RM 50
18.0 Local Sand filling around and under Foundation as applicable. Cu.Mtr. 30019.0 Stone soling below foundations wherever specified in approved
drawings during detailed engineering Cu.Mtr. 200
20 All civil works as per technical specification and approved drawing including internal finish but excluding excavation, PCC, RCC, reinforcement steel and external finishing which shall be paid seperately under respective items of BPS
20.1 Control room cum administrative building (Double story) as per TSSq. m. 1200
20.2 Car Parking shed (for 5 cars) LS 120.3 Security Room LS 1
21 External finish as per specification for following buildings:
21.1Control room cum administrative building (Double story) as per TS
Sq. m. 1200
21.2 Car Parking shed (for 5 cars) LS 121.3 Security Room LS 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 32 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
22Septic tank as per specification and approved design according to International/British standards and soak pit as per approved drawing excluding concrete & reinforcement (For 50 users)
LS 3
23 Geotechnical /Soil Investigation as per technical specification LS 124 Detail Survey andcontour mapping of the site LS 1
25 Site levelling25.1 Earth work in cutting & Filling in all types of soils including
soft/disintegrated rockCu.Mtr. 21000
25.2 Earth work in Filling with borrowed earth Cu.Mtr. 5000
26.0
All civil works for Boundary wall including excavation, concrete,reinforcement steel ,structural steel, plaster, painting, barbed wireand concertina coil etc all complete as per technical specification(2.5 m high brick masonary wall and 0.5 m high angle support ontop).
RM 500
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 33 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
27 Construction of retaining wall with random Rubble masonary incement sand mortar (1:6) including levelling up with cement concrete(1:6:12),providing weep holes of PVC pipes (150 mm dia) withnecessary filter material at the mouth of weep holes,50 mm thickcement concrete (1:2:4) copping on the top of wall, 100 mm thickPCC (1:4:8) below RR masonary work,excavation of foundation forall lifts up to 3m above lower level . Item of excavation, PCC (1:2:4 &1:4:8) shall be measured and paid seperately under respective itemsof BPS
Cu. M 8000
28.0Supplying, providing stone work packed in steel wire crats as perdesign & drawing to be developed by the contractor for all leads &lifts along the boundary wall & other places as required.
Cu. M 4000
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 1 PAGE 34 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.
Portion in Foreign CurrencyPortion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
29.0 Approach Road- Construction of 6m wide black top(Bituminous/asphalt) road with wideblack top pavement and earthenshoulders on either side of road, Water bound macadum of suitablethickness as per design below pavement shall be laid as pertechnical specification.
Sq. m. 900
Sub-Total Part-C
Total For PART 1 Phutung Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 4( Total of column 9 and 11 to be carried forward to Schedule 5: Grand Summary)
# Specify currency in accordance with ITB Clause 12.1 and corresponding BDS clauses, Vol.I of the Bidding Documents.
Name of Bidder: Date:
Signature of Bidder:
(Printed Name)
(Designation)
(Common Seal)
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4b, PART 1 PAGE 35 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services (Common for all)(b):Training Charges for training to be imparted abroad
Currency Unit rate Total Training Charges
1 2 3 4 5 6 7 8 = 4x5 x 7i) Control & Protection and Substation Automation System
4 10
ii) Switchyard Equipments and GIS Equipments 4 10
iii) Telecommunication Equipment (SDH ,MUX & NMS (Craft Terminal)) and PLCC
2 5
Total for Training Charges (total of coulmn 8 to be carried forward to Schedule 5: Grand summary)
Name of Bidder: Date: Signature of Bidder: (Printed Name)
(Designation) (Common Seal)
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Total Training Charges
A
Sl. No. Description
Item for which training is to be imparted. Country where training is to be
imparted
Nos. of Trainee
Training duration in
days
Training to Owners personnel on Design , testing and Maintenance aspect as per Section Project, Technical Specification at manufacturer's works
PACKAGE A-2
SPECIFICATION NO: SCHEDULE 4c, PART 1, PAGE 36 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services (Common for all)(c):Training Charges for training to be imparted to Employer's Personnel by Bidder's Instructor in Nepal
Sl. No.
Item for which training is to be imparted. Currency Unit rate Total Training Charges
1 2 3 4 5 6 7 = 4x 6i) Control & Protection 5
ii) Substation Automation System including integration aspect of existing SCADA (of Siemens supplied SINAUT Spectrum Software) at Load Dispatch Center
5
iii)GIS equipment 4iv) Telecommunication Equipment (SDH, MUX & NMS (Craft Terminal)) and PLCC
4
v) Transformers 2
Total for Training Charges ( Total of column 7 to be carried forward to Schedule 5: Grand Summary)
Date: Signature:
Printed Name:
Designation:
Common Seal:
NOTE: To and fro charges and accommodation for the Instructor (Trainer) and Training material for the Trainees shall be included in the prices quoted by the bidder. However, arrangments for trainees and premises for conducting the training shall be arranged by OWNER.
Description of the Test
Training duration in days
Training Charges for Contractors Trainers
a)
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
On Job training on operation, maintenance and testing & commissioning aspect at each substation as per section Project, Technical Specification
Kathmandu Valley Transmission Capacity Reinforcement Project
REMARKS: 2. On Job Training in Nepal: The traveling and living expenses of Owner’s personnel for the training programme conducted in Nepal shall be borne by the Owner.
PACKAGE A-2
Specification No.: Schedule - 4d) Page 37 of 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services (Common for all)(d): Maintenance Charges
CurrencyTotal Maintenance
Charges
1Maintenance Charges for Communication Equipments including SDH & MUX. for One (1) year during Warranty period
Year 1
2Maintenance Charges for Communication Equipments including SDH & MUX. for Six (6) years after Warranty period
Year 6
Total Maintenance Charges (To be carried forwardto Schedule 5: Grand Summary)
Date: Signature:
Printed Name:
Designation:
Common Seal:
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Sl No Description Unit Qty.
Total Maintenance Charges
Kathmandu Valley Transmission Capacity Reinforcement Project
PACKAGE A-2
SPECIFICATION NO.: SCHEDULE - 5 PAGE 38 OF 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 5: Grand Summary
1 2 3 4 5 6 7=1+3+5 8=2+4+6 1 TOTAL SCHEDULE NO. 1
Plant and Equipment including Mandatory Spares to besupplied from abroad.
2 TOTAL SCHEDULE NO. 2Plant and Equipment including Mandatory Spares Partsto be supplied from within Nepal
3 TOTAL SCHEDULE NO. 3Design Services
4 TOTAL SCHEDULE NO. 4(a) Installation and construction charges
(b) Training charges for training to be imparted abroad
(c) Training charges for training to be imparted in Nepal
(d) Maintenance charges
GRAND TOTAL [1+2+3+4]
Date: Signature:Place:
Printed Name:Designation:
Common Seal:
Grand Total
Total Price Foreign
Total Price Local
Sl. No. DescriptionTotal Price
Foreign Total Price
Local
Phutung Substation Chapagaun Substation Jorpati (Mulpani) Substation
Total Price Local
Total Price Foreign
Total Price Local
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Total Price Foreign
PACKAGE A-2
SPECIFICATION NO.: SCHEDULE - 6 PAGE 39 OF 39
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 6: Recommended Availability/Optional Spares Parts and recommended Test Equipment in line with technical SpecificationsItem No. Name & Description of
PartsName of Original
ManufacturerPart No. Number of Units
in each setTotal No. of Sets to be provided
Unit Price Total Price Remarks
Date: Signature: Printed Name:
Designation:Common Seal:
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
PACKAGE A-2
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 1 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
PART 2 132/11 kV Chapagaun Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIESA POWER TRANSFORMER
1.0 POWER TRANSFORMER1.1 31.5/45 MVA , 132/11 KV, 3-phase Indoor Transformer (Excluding
insulating oil)Nos. 2
1.2 Insulating oil for 31.5/45 MVA , 132/11 KV, 3-phase Transformer (* 1Lot = Oil for 1 Transformers)
Lot* 2
2.0 Testing & Maintenance Equipments2.1 Oil Storage Tank No. 12.2 Transformer Oil Filtration plant (6KLPH) No 1
3 LT TRANSFORMER3.1 315 kVA, 11/0.400kV (Indoor/Outdoor) with Bus disconnector, Power
fuse and all other accessories.Nos 1
3.2 11kV Bus disconnector, Power fuse and all other accessories for above transformer.
Set 1
B 145 kV equipment1 145KV GIS Equipment
1.1 145kV, SF6 GIS Bus Bars Module [ Module description as per Technical Project specification]
Set 2
1.2 145kV, SF6 GIS ICT bay Module [ Module description as per Technical Project specification]
Set 2
1.3 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification]
Set 4
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 2 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
1.4 145kV, SF6 GIS Bus Coupler bay Module [ Module description as per Technical Project specification]
Set 1
1.5 145kV, 1250A, 31.5kA SF6/Air Bushing for Connecting GIS to AIS alongwith support structure
Nos 12
1.6 145kV, 1250A, 31.50kA SF6/Air Bushing for Connecting GIS to Transformer alongwith support arrangement
Nos 6
1.7145kV, 1250A, 1phase SF6 GIS Bus duct alongwith support structure
OPTION-I2000A, 31.5kA for 1 sec. Single Phase Mtr. 600
OPTION-II2000A, 31.5kA, 1sec three phase Mtr. 200Note : Bidder is required to quote for either option-I or Option-II
1.8 Testing & Maintenance Equipment for GIS1.8.1 Partial Discharge Monitoring System for 145kV GIS System as per
Technical Specification, GISSet 1
1.8.2 Dew Point meter for 145kV GIS System Set 11.8.3 SF6 Gas Leak Detector for 145kV GIS System Set 11.8.4 EOT crane for 145kV GIS Hall Set 11.8.5 SF6 Gas Analyser Set 1
2.0 145KV Outdoor Equipment2.1 145 kV Surge Arrestors
2.1.1 120 kV Surge Arrestors (1- Phase) Nos 122.2 145 kV Post insulators, as required Nos 12
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 3 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
C RELAY PANELS (WITH AUTOMATION)1.0 132 kV 1.1 Line Control & Protection Panel with distance relay / Differential relay Set 4
1.2 Current Differential Relay for other end of line Nos 4
1.3 Transformer Control & Protection Panel (For HV side) Set 21.4 Bus Bar Protection Panel Set 1
D MV Switchgear1.0 11 kV Indoor VCB Switchgear1.1 11kV 2500A Incomer Set 21.2 11kV 1250A Outgoing Set 101.3 11kV 2500A Buscoupler Set 11.4 11kV 2500A Trunking Set 1
2 Surge arrestors with accessories for 11 kV Line Nos 18
E COMMON EQUIPMENTS1.0 Relay Test tool kit Set 02.0 Time synchronisation equipment No. 1
F SUBSTATION AUTOMATION Complete Substation Automation System (SAS) for substation including hardware and software for the substation & remote control stations alongwith associated equipments for the following bays as per Technical Specification
1.0 Main bays to be automated1.1 132 kV system Bay Nos 7
1.2 11 kV system Bay Nos 13
1.3 BCU for controlling & monitoring of Auxilary System Set 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 4 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
G Teleprotection & communication Equipments 1 PBAX with following configuration as per TS Set 1
1.1 2 wire subscriber interface card with capacity 32 local subscribers or as required (along with 32 nos. Instruments)
1.2 4 wire E & M interface card with capacity 8 nos. trunks (For PLCC or Other communication mode) as required
1.3 E-1 interface with 2 trunks G-7031.4 2 wire interface with 1 trunk (For PSTN)2 Testing & Maintenance equipment (print test kit only) Set 13 4 wire telephone equipment Lot 1
H LT Switchgear (As per Technical specification)1 415V Main switchboard Set 12 415V ACDB Set 13 415V MLDB Set 14 415V Emergency LDB Set 15 220V DCDB Sets 16 48V DCDB Sets 1
I Batteries1 220V
1.1 600 AH Nos 2J Float Cum Boost Battery Charger
1.0 220V Float Cum Boost Battery Charger 1.1 80A/80A Nos 2
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 5 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
K Fire Protection System1 Portable /Trolley/Wheel mounted extinguishers
1.1 9 litre water type Nos 51.2 50 litre foam type Nos 21.3 4.5 kg CO2 type Nos 13
1.4 4.5 kg Dry Chemical Power (DCP) type Nos 52 Smoke detection system Set 13 Fire detection and Alarm System Set 1
L Cables along with clamps, glands, lugs and straight joints etc.
1 Power Cables - (1.1kV grade)1.1 3.5Cx300 sqmm (XLPE) cable for filter Machine along with termination
arrangement as per TSKM 0.3
2 Power Cables - (12kV grade)2.1 1Cx800 sqmm (XLPE) copper cable for Incomer with termination
arrangement as per TSKM 2
2.2 3Cx300 sqmm (XLPE) Aluminum cable for outgoing feeders along with termination arrangement as per TS including cable duct pipe for laying outside cable trench to nearest pole.
KM 1
3 Power Cables - (145kV grade)3.1 1Cx500 sqmm (XLPE) copper cable for line bay along with termination
arrangement as per TSKM 1
3.2 1Cx240 sqmm (XLPE) copper cable for Transformer along with termination arrangement as per TS
KM 0.5
Note:Cables are to be used as a option to Bus ducts, if required
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 6 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
M Air conditioning System for Control Building1 High wall type split AC unit of 2 TR capacity Nos 15
N Fabrication, galvanising and supply of following Steel Structures including nuts, bolts, all types of washers, packplates, step bolts and gusset plates including foundation bolts.
1.0 Lattice Structure including Foundation Bolts MT 402.0 Pipe Structure including Foundation Bolts . MT 103.0 Fastners and step bolts.(Nuts,Bolts & Washers) MT 5
O Communication equipments 1 Transmission equipments
1 SDH Equipment ( STM- 4 MADM, upto 3 MSP protected directions)1.1
Base Equipment (Common cards, Cross-connect/control cards, Optical base cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc. fully equipped including Optical interphase/SFPs and Tributary cards for full function with future proviison of communication and protection system.
Set 1
2 Termination Equipment2.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards) for full functioning of the system
Set 1
3 Equipment Cabinets3.1 For Drop/Insert Multiplexer No. 13.2 For SDH Equipment No. 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 7 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
4 Main Distribution Frame(100 pairs) No. 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 8 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
5 BOQ for Auxiliary Power Supply Equipments 5.1 SMPS based 48V DC Power Supply (DCPS) system Nos. 25.2 VRLA type Battery bank for above DCPS system Nos. 2
At Kathmandu LDC
6 Termination Equipment6.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of system
Set 1
7 Equipment Cabinets7.1 For Drop/Insert Multiplexer No. 1
8 Main Distribution Frame(100 pairs) No. 1
Sub-Total Part-A
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 9 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Part-B: CONTRACTOR ASSESSED QUANTITIES
A Erection HardwareInsulator strings, Disc Insulators, Hardware, conductor, Al tube, bus-bar materials, cable trays, clamps, spacers, connectors including equipment connectors, Junction box, earthwire, buried cable trenches/pipe equipment & lighting, all accessories etc. for the following:
1.0 145kV GIS Termination Arrangement:1.1 Line Bay Set 41.2 Transformer Bay Set 2
2.0 Earthing and lightning protection including necesaary connectors/connections, risers etc. complete in all respect( but excluding LM structures for Lightning protection)
2.1 Earth Conductor (copper) LS 12.2 Earth Rod (copper clad steel) LS 12.3 Equipment for lightning protection LS 1
B Fire Protection System1 Fire Protection system with complete U/G & O/G piping, Tanks, building
and accessories etc. complete for Indoor Transformer: Transformer Set 2
1.1 132/11 KV, 3-phase Transformer
C Illumination System1 Control Building cum administrative building LS 12 Switchyard lighting Outdoor LS 13 Street lighting LS 14 Security Room LS 15 Car parkings LS 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 10 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
D Air conditioning & ventilation System 1.0 Air conditioning 1.1 Panel room in 145kV GIS Hall LS 1
2.0 Ventilation system 2.1 145KV GIS hall LS 1
E POWER & CONTROL CABLES1 Power Cables(PVC)- (1.1kV grade) LS 12 Power Cables (XLPE)(excluding 3.5Cx300 sqmm (XLPE) cable for filter
Machine)- (1.1kV grade)LS 1
3 Control Cable (PVC)- (1.1kV grade) LS 1
4 Cable glands, lugs & straight through joints for Power & Control cablesLS 1
F
Integration of all 132/11kV Bays under present scope with the SCADA of SIEMENS (SINAUT Spectrum) at Load Dispatch Centre, Kathmandu including supply of Hardware, Software, accessories etc. as per TS Section Project.
LS 1
Sub-Total Part-B
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 11 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Part-C: Mandatory Spares(I) Mandatory Spare List for Transformer
For 132/11 KV, 3-phase Transformer1.0 Cooler fan with Motor No. 12.0 Buchholz Relay(Main Tank) complete with floats and contacts Set 13.0 Local and Remote WTI with sensing device and contact(each) Set 14.0 Magnetic oil level gauge No. 15.0 Strarters, contactors,switches & Relays for Electrical control panels(One
ste of each type)Set 1
6.0 Remote Tap postion Indiactor No. 17.0 Spare insulating oil to be handed over to Owner after commisioning for
O&M requirementKL 10
(II) SPARES FOR 145kV GIS
1 General
1.1 SF6 gas Pressure Relief Devices, 1Nos. of each type Set 1
1.2SF6 Pressure gauge cum switch OR Density monitors and pressureswitch as applicable (1 no. of each type)
Set 1
1.3Coupling device for pressure gauge cum switch for connecting Gashandling plant
Set 1
1.4 Rubber Gaskets, “O” Rings and Seals for SF6 gas of each type Set 1
1.5 Molecular filter for SF6 gas with filter bags(20% of total weight) Set 1
1.6 All types of Control Valves for SF6 gas of each type Set 1
1.7 SF6 gas (20 % of total gas quantity) Set 1
1.8 All types of coupling for SF6 gas (1 no. of each type) Set 1
1.9 Pipe length (Copper or Steel as applicable) for SF6 Circuit of each typeSet 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 12 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
1.10Covers with all accessories necessary to close a compartment in case ofdismantling of any part of the Enclosure to ensure the sealing of thiscompartment
1.10.1 For 3 Phase Enclosure if applicable Nos. 1
1.10.2 For Single phase enclosure if applicable Nos. 1
11Locking device to keep the Dis-connectors (Isolators) and Earthingswitches in close or open position in case of removal of the drivingMechanism
Sets 1
2 145 KV SF6 CIRCUIT BREAKER:
2.1 Rubber gaskets, `O' rings and seals for SF6 gas (1 No. of each type)Sets 1
2.2 Trip coil assembly with resistor as applicable Sets 1
2.3 Closing coil assembly with resistor as applicable . Sets 1
2.4Relays, Power contactors, push buttons, timers & MCBs etc (1 No. ofeach type & rating)
Sets 1
2.5 Closing coil assembly (including valve, if applicable) Sets 1
2.6 Trip coil assembly (including valve, if applicable) Sets 1
2.7 Auxiliary switch assembly of each type Sets 1
3 145 KV ISOLATORS :
3.1Copper contact fingers for dis-connector male & female contact for onecomplete (3-phase) dis-connector of each type and rating
Sets 1
3.2Copper contact fingers for earthing switch male & female contacts, forone complete(3-phase) earthing switch of each type and rating
Sets 1
3.3Open / Close contactor assembly, timers, key interlock for one complete(3 phase) dis-connector and (3 phase) earthing switch (1 No. of eachtype and rating)
Sets 1
3.4 Push button switch - (1 No. of each type & rating) as applicable Sets 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 13 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
3.5 Limit switch and Aux. Switches for complete 3 phase equipment 3.5.1 For isolator Sets 1
3.5.2 For earth switch Sets 1
4 145 KV CURRENT TRANSFORMER
4.1 Gas insulated complete CT of each type and rating with enclosure. Lot 1
4.2 Secondary bushing of each type Sets 1
5 120kV SA5.1 Complete LA No. 15.2 Surge counter/monitor Nos. 1
III) C&R PANELS1 Transformer protection panel :
1.1 Transformer differential protection No. 12 Breaker Relay panel: Part of CRP
2.1 Self reset trip relay (relay of each type) Set 12.2 Hand reset trip relay(relay of each type) Set 1
IV) SAS1 Bay Control Unit (IED) of each type Set 12 Ethernet Switch of each type Set 1
V) COMMON SPARES1 Bay unit Module No. 12 2 wire local subscriber interface card for PABX No. 13 E1 Interface card for PABX No. 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 2 PAGE 14 OF 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
VI) 11 kV Switchgear1 11kV Vacuum Interrupter for Incomer and Outgoing No 32 Tripping Coils Nos 33 Closing Coils Nos 34 Spring Charging Motor Set 15 Protection Relays
5.1 3 phase Overcurrent Relay, for 11kV side one of each type Nos 15.2 Ground Fault Relay, for 11kV side, oe of each type Nos 16 Ammeter, Nos one of each rating Nos 17 Voltmeter, Nos Nos 18 kVA Meter, each Nos 19 CTs as in Outgoing Feeder Set 110 Operating Handle Nos 111 Indicating lamps (100% of used), Lot Lot 1
Sub-Total Part-CTotal For PART 2 Chapagaun Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 1 ( Total of column 9 to be carried forward to Schdule 5: Grand Summary)Note : 1) Bidder is required to quote prices in this Schedule for all the individual items/sub-items.
* Strike-out whichever is not applicable.
Name of Bidder: Date:
Signature of Bidder: (Printed Name) (Designation) (Common Seal)
2.) The Prices of equipments are inclusive of type test charges
3.) BOQ given above is indicative only based on the scope of work as given in Employer's Requirements. The quantities mentioned above may undergo change during detailed engineering to meet the functional requirement and scope of work defined in Employer's Requirements.
Specify currency in accordance with BDS ITB Clause 32.1, Part-I of the Bidding Documents.
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 2 PART 2 PAGE 15 OF 30
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No.2: Plant and Equipment including Mandatory Spares Parts to be supplied from within Nepal LC: Local Currency (ALL Price in Local Currency)
Total Amount (Excluding Taxes
)
Custom, VAT and
other taxes
Unit Rate Amount Unit Rate Amount
1 2 3 4 5 6 = (4) x (5) 7 8=(4)x(7) 9=6+8 10
PART 2 132/11 kV Chapagaun Substation (132V GIS & Indoor)Part-A : EMPLOYER ASSESSED QUANTITIES
Part-B: CONTRACTOR ASSESSED QUANTITIES
Part-C: Mandatory Spares
Total For PART 2 Chapagaun Substation [(Part-A+ Part-B+ Part C)]Total for Schedule 2 (Total of column 9 to be carried forward to Schdule 5: Grand Summary)
Note : 1) Bidder is required to quote prices in this Schedule for all the items in Schedule 1 which they wish to supply from within Nepal.
# Specify currency in accordance with BDS ITB Clause 32.1, Part-I of the Bidding Documents.* Strike-out whichever is not applicable.
a Specify currency in accordance with ITB 19.1 of the BDS.
Name of Bidder: Date:
Signature of Bidder: (Printed Name) (Designation)
(Common Seal)
Ex Faxtory Price (Excluding VAT) in LC
Inland transportation to site in LC
b Column 5 Price shall include all customs duties and sales and other taxes already paid or payable on the components and raw materials used in the manufacture or assembly of the item or the customs duties and sales and other taxes already paid on previously imported items.
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Item No. Item description Unit Quantity
2.) The Prices of equipments are inclusive of type test charges
Name of Bidder: Package A-2 Signature of Bidder:
SPECIFICATION NO SCHEDULE 3 , PART 1 PAGE 16 of 30
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Local Currency Portion
Foreign Currency Portion
Quantity Unit NRs Currency LC FC1 2 3 4 5 6 7=3x5 8=3x6
PART 2132/11 kV Chapagaun Substation (132V GIS & Indoor)
Not Applicable
Total for Schedule 3 (Total of column 7 & 8 to be carried forward to Schdule 5: Grand Summary)
NOTE: The design cost is included in schedule 1.
Name of Bidder: Date:Signature of Bidder: (Printed Name) (Designation) (Common Seal)
Schedule A-3: Design Services
NEPAL ELECTRICITY AUTHORITY
Item No. Item DescriptionEstimated
Unit Prices Total Prices
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Name of Bidder PACKAGE A2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 17 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
PART 2 132/11 kV Chapagaun Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIES
A1 POWER TRANSFORMER
1.0 POWER TRANSFORMER1.1 31.5/45 MVA , 132/11 KV, 3-phase Indoor Transformer (Excluding insulating oil) Nos. 2
1.2 Insulating oil for 31.5/45 MVA , 132/11 KV, 3-phase Transformer (* 1Lot = Oil for 1 Transformers)
Lot* 2
2 LT TRANSFORMER2.1 315 kVA, 11/0.400kV (Indoor/Outdoor) with Bus disconnector, Power fuse and all
other accessories.Nos 1
2.2 11kV Bus disconnector, Power fuse and all other accessories for above transformer. Set 1
B 145 kV equipment1 145KV GIS Equipment
1.1 145kV, SF6 GIS Bus Bars Module [ Module description as per Technical Project specification]
Set 2
1.2 145kV, SF6 GIS ICT bay Module [ Module description as per Technical Project specification]
Set 2
1.3 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification]
Set 4
1.4 145kV, SF6 GIS Bus Coupler bay Module [ Module description as per Technical Project specification]
Set 1
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 18 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
1.5 145kV, 1250A, 31.5kA SF6/Air Bushing for Connecting GIS to AIS alongwith support structure (Single Phase)
Nos 12
1.6 145kV, 1250A, 31.50kA SF6/Air Bushing for Connecting GIS to Transformer alongwith support arrangement (Single Phase)
Nos 6
1.7 245kV, 1600A, 1phase SF6 GIS Bus duct alongwith support structureOPTION-I2000A, 40kA for 1 sec. Single Phase Mtr. 600
OPTION-II2000A, 40kA, 1sec three phase Mtr. 200Note : Bidder is required to quote for either option-I or Option-II
1.8 Testing & Maintenance Equipment for GIS1.8.1 Partial Discharge Monitoring System for 145kV GIS System as per Technical
Specification, GIS
Set 1
1.8.2 EOT crane for 245kV GIS Hall Set 1
2.0 145KV Outdoor Equipment2.1 145 kV Surge Arrestors
2.1.1 120 kV Surge Arrestors (1- Phase) Nos 122.2 145 kV Post insulators, as required Nos 12
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 19 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
C RELAY PANELS (WITH AUTOMATION)1.0 132 kV 1.1 Line Protection Panel with distance relay / Differential relay Set 41.2 Current Differential Relay for other end of line Nos 41.3 Transformer Protection Panel (For HV side) Set 21.4 Bus Bar Protection Panel Set 1
D MV Switchgear1.0 11 kV Indoor VCB Switchgear1.1 11kV 2500A Incomer Set 21.2 11kV 1250A Outgoing Set 101.3 11kV 2500A Buscoupler Set 11.4 11kV 2500A Trunking Set 1
2 Surge arrestors with accessories for 11 kV Line Nos 18
E COMMON EQUIPMENTS
1.0 Special Relay Test Tool kit No 1
F SUBSTATION AUTOMATION Complete Substation Automation System (SAS) for substation including hardware and software for the substation & remote control stations alongwith associated equipments for the following bays as per Technical Specification
1.0 Main bays to be automated1.1 132 kV system Bay Nos 71.2 11 kV system Bay Nos 131.3 BCU for controlling & monitoring of Auxilary System Set 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 20 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
G Teleprotection & communication Equipments 1 PBAX with following configuration as per TS Set 1
1.1 2 wire subscriber interface card with capacity 32 local subscribers or as required (along with 32 nos. Instruments)
1.2 4 wire E & M interface card with capacity 8 nos. trunks (For PLCC or Other communication mode) as required
1.3 E-1 interface with 2 trunks G-7031.4 2 wire interface with 1 trunk (For PSTN)2 Testing & Maintenance equipment (print test kit only) Set 13 4 wire telephone equipment Lot 1
H LT Switchgear (As per Technical specification)1 415V Main switchboard Set 12 415V ACDB Set 13 415V MLDB Set 14 415V Emergency LDB Set 15 220V DCDB Sets 16 48V DCDB Sets 1
I Batteries1 220V
1.1 600 AH Nos 2
J Float Cum Boost Battery Charger
1 220V Float Cum Boost Battery Charger
1.1 80A/80A Nos 2
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 21 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
K Fire Protection System1 Portable /Trolley/Wheel mounted extinguishers
1.1 9 litre water type Nos 51.2 50 litre foam type Nos 21.3 4.5 kg CO2 type Nos 13
1.4 4.5 kg Dry Chemical Power (DCP) type Nos 52 Smoke detection system Set 13 Fire detection and Alarm System Set 1
L Cables along with clamps, glands, lugs and straight joints etc.1 Power Cables - (1.1kV grade)
1.1 3.5Cx300 sqmm (XLPE) cable for filter Machine along with termination arrangement as per TS
KM 0.3
2 Power Cables - (12kV grade)2.1 1Cx800 sqmm (XLPE) copper cable for Incomer with termination arrangement as per
TSKM 2
2.2 3Cx300 sqmm (XLPE) Aluminum cable for outgoing feeders along with termination arrangement as per TS including cable duct pipe for laying outside cable trench to nearest pole.
KM 1
3 Power Cables - (145kV grade)3.1 1Cx500 sqmm (XLPE) copper cable for line along with termination arrangement as
per TSKM 1
3.2 1Cx240 sqmm (XLPE) copper cable for Transformer along with termination arrangement as per TS
KM 0.5
Note:Cables are to be used as a option to Bus ducts, if required
M Air conditioning System for Control building1 High wall type split AC unit of 2 TR capacity Nos 15
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 22 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
N Fabrication, galvanising and supply of following Steel Structures including nuts, bolts, all types of washers, packplates, step bolts and gusset plates including foundation bolts.
1.0 Lattice Structure including Foundation Bolts MT 402.0 Pipe Structure including Foundation Bolts . MT 103.0 Fastners and step bolts.(Nuts,Bolts & Washers) MT 5
O Communication equipments 1 Transmission equipments
1 SDH Equipment ( STM- 4 MADM, upto 3 MSP protected directions)1.1 Base Equipment (Common cards, Cross-connect/control cards, Optical base cards,
Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc. fully equipped including Optical interphase/SFPs and Tributary cards for full function with future proviison of communication and protection system.
Set 1
2 Termination Equipment2.1
Drop/Insert Multiplexer Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards) for full functioning of the system
Set 1
3 Equipment Cabinets3.1 For Drop/Insert Multiplexer No. 13.2 For SDH Equipment No. 1
4 Main Distribution Frame(100 pairs) No. 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 23 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
5 BOQ for Auxiliary Power Supply Equipments 5.1 SMPS based 48V DC Power Supply (DCPS) system Nos. 15.2 VRLA type Battery bank for above DCPS system Nos. 1
At Kathmandu LDC6 Termination Equipment
6.1 Drop/Insert Multiplexer Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards and accessories) for full functioning of system
Set 1
7 Equipment Cabinets7.1 For Drop/Insert Multiplexer No. 1
8 Main Distribution Frame(100 pairs) No. 1
Sub-Total Part-A
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 24 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Part-B: CONTRACTOR ASSESSED QUANTITIES
A Erection HardwareInsulator strings, Disc Insulators, Hardware, conductor, Al tube, bus-bar materials, cable trays, clamps, spacers, connectors including equipment connectors, Junction box, earthwire, buried cable trenches/pipe equipment & lighting, all accessories etc. for the following:
1.0 145kV GIS Termination Arrangement:1.1 Line Bay Set 41.2 Transformer Bay Set 2
2.0 Earthing and lightning protection including necesaary connectors/connections, risers etc. complete in all respect( but excluding LM structures for Lightning protection)
2.1 Earth Conductor (copper) LS 12.2 Earth Rod (copper clad steel) LS 12.3 Equipment for lightning protection LS 1
B Fire Protection System1 Fire Protection system with complete U/G & O/G piping, Tanks, building and
accessories etc. complete for Indoor Transformer: Transformer Set 2
1.1 132/11 KV, 3-phase Transformer
C Illumination System1 Control Building cum administrative building illumination LS 12 Switchyard lighting Outdoor LS 13 Street lighting LS 14 Security Room LS 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 25 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
5 Car parkings LS 1
D Air conditioning & ventilation System 1.0 Air conditioning system 1.1 Panel room in 145kV GIS Hall LS 1
2.0 Ventilation system 2.1 145KV GIS hall LS 1
E POWER & CONTROL CABLES1 Power Cables(PVC)- (1.1kV grade) LS 12 Power Cables (XLPE)(excluding 3.5Cx300 sqmm (XLPE) cable for filter Machine)-
(1.1kV grade)LS 1
3 Control Cable (PVC)- (1.1kV grade) LS 1
4 Cable glands, lugs & straight through joints for Power & Control cables LS 1
FIntegration of all 132/22/11kV Bays under present scope with the SCADA of SIEMENS (SINAUT Spectrum) at Load Dispatch Centre, Kathmandu including supply of Hardware, Software, accessories etc. as per TS Section Project.
LS 1
Sub-Total Part-B
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 26 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
PART-C: Civil Works (As per technical specification)
1.0 Excavation in all types of soil and rock including backfilling disposal etc. for all leads
and lifts Lot 1
2.0 Providing and laying of Plain Cement Concrete (PCC) (1:4:8) Cu.Mtr. 1000
3.0 Providing and laying of Plain Cement Concrete (PCC) (1:2:4) Cu.Mtr. 300
4.0 Providing and laying of Reinforced Cement Concrete Design Mix (M25)
including pre cast, shuttering, Grouting of pockets & underpinning but
excluding steel reinforcement.
Cu.Mtr. 2000
5.0 Providing and laying Plain Cement Concrete 1:5:10 (1 cement : 5 sand : 10
Stone aggregate)Cu.Mtr. 500
6.0 Steel Reinforcement (Fe 500) MT 200
7.0 Miscellaneous Structural steel used for rails , plates for rail fixing, ,gratings,
gratings supports etc for transformer /reactor foundation,cable supportstand
earthing cleats ,chequered plates, embedments, edge protection angles for
cable trenches but excluding the reinforcement steel and steel for lattice and
pipe structures which shall be paid seperately.
MT 30
8.0 Stone filling (40mm) over grating of Transformer /reactor Foundation Cu.Mtr. 40
9.0
Stone spreading including antiweed treatment in switchyard but excluding
PCC.Sq. Mtr. 2000
10.0
Supplying & laying hume pipe with collars of grade (NP-3) but excluding
concrete of bed/support/encasing of hume pipes which shall be paid
seperatelyunder respective items of BPS
10.1 250mm dia RM 150
10.2 300mm dia RM 120
10.3 450mm dia RM 80
10.4 600mm dia RM 40
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 27 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
11.0 Concrete road as per technical specification and approved drawing but
excluding reinforcement & concrete which shall be paid seperately under
respective items of BPS11.10 Concrete Road 4m wide Sq. m. 400
12.0
Construction of rail-cum-raod as per technical specification and approved
drawing including all items such as excavation, compaction, rolling, watering,
WBM, etc but excluding concrete, reinforcement and structural steel which
shall be paid seperately under respective items of BPS
12.1 Section having two rails Sq. m. 100
13.0
Chain link Switchyard fencing as per technical specification and approved
drawing but excluding concrete which shall be paid seperately under
respective items of BPS
RM 260
14.0
Switch yard Gate excluding concrete which shall be paid seperately under
respective items of BPS
Nos.2
15.0 All civil works for construction of drains as per technical specification and
approved drawing excluding concrete which shall be paid seperately under
respective items of BPS15.1 Type AA (300mm wide x Depth up to 600mm) RM 500
15.2 Type BB (450 wide x Depth From 600 to 900mm) RM 200
15.3 Type CC (600 wide x Depth From 900 to 1200mm) RM 200
15.4 Type DD (750 wide x Depth From 1200 to 1500mm) RM 200
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 28 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
16.0 External water supply as per technical specification from borewell/single
point of water supply within substation boundary to Fire water Tank, control
room Building and other buildings as applicable including all items like
excavation, pipes, fittings, jointings, valves, chambers/manholes etc
16.1 80mm Dia GI Pipe RM 10016.2 50mm dia GI pipe RM 8016.3 40mm dia GI pipe RM 6016.4 25mm Dia GI Pipe RM 40
17.0 External sewerage system including all item such as excavation, piping, pipe
fittings, manholes, gali trap, gali chamber etc.17.1 (i) 250 mm Dia. RM 5017.2 (i) 150 mm Dia. RM 50
18.0 Local Sand filling around and under Foundation as applicable. Cu.Mtr. 30019.0 Stone soling below foundations wherever specified in approved drawings
during detailed engineeringCu.Mtr. 200
20 All civil works as per technical specification and approved drawing
including internal finish but excluding excavation, PCC, RCC, reinforcement
steel and external finishing which shall be paid seperately under respective
items of BPS
20.1 Control room cum administrative building (Double story) as per TS Sq. m. 1200
20.2 Car Parking shed (for 5 cars) LS 1
20.3 Security Room LS 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 29 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
21 External finish as per specification for following buildings:
21.1 Control room cum administrative building (Double story) as per TS Sq. m. 1200
21.2 Car Parking shed (for 5 cars) LS 1
21.3 Security Room LS 1
22Septic tank as per specification and approved design according to International/British standards and soak pit as per approved drawing excluding concrete & reinforcement (For 50 users)
LS 3
23 Geotechnical /Soil Investigation as per technical specification LS 124 Detail Survey andcontour mapping of the site LS 1
25 Site levelling25.1 Earth work in cutting & Filling in all types of soils including soft/disintegrated
rockCu.Mtr. 7000
25.2 Earth work in Filling with borrowed earth Cu.Mtr. 5000
26
All civil works for Boundary wall including excavation, concrete, reinforcement steel,structural steel, plaster, painting, barbed wire and concertina coil etc all complete asper technical specification (2.5 m high brick masonary wall and 0.5 m high anglesupport on top).
RM 400
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 2, PAGE 30 of 30
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency (in
NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
27 Construction of retaining wall with random Rubble masonary in cement sand
mortar (1:6) including levelling up with cement concrete (1:6:12),providing
weep holes of PVC pipes (150 mm dia) with necessary filter material at the
mouth of weep holes,50 mm thick cement concrete (1:2:4) copping on the top
of wall, 100 mm thick PCC (1:4:8) below RR masonary work,excavation of
foundation for all lifts up to 3m above lower level . Item of excavation, PCC
(1:2:4 & 1:4:8) shall be measured and paid seperately under respective items of
BPS
Cu. M 4000
28 Supplying, providing stone work packed in steel wire crats as per design &
drawing to be developed by the contractor for all leads & lifts along the
boundary wall & other places as required.
Cu. M 2000
29 Approach Road- Construction of 6m wide black top (Bituminous/asphalt)
road with wideblack top pavement and earthen shoulders on either side of
road, Water bound macadum of suitable thickness as per design below
pavement shall be laid as per technical specification.
Sq. m. 0
Sub-Total Part-CTotal For PART 2 Chapagaun Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 4( Total of column 9 and 11 to be carried forward to Schedule 5: Grand Summary)
# Specify currency in accordance with ITB Clause 12.1 and corresponding BDS clauses, Vol.I of the Bidding Documents.
Name of Bidder: Date:
Signature of Bidder: (Printed Name) (Designation) (Common Seal)
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 1 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
PART 3 132/11 kV Jorpati (Mulpani) Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIESA POWER TRANSFORMER
1.0 POWER TRANSFORMER1.1 31.5/45 MVA , 132/11 KV, 3-phase Indoor Transformer (Excluding
insulating oil)Nos. 2
1.2 Insulating oil for 31.5/45 MVA , 132/11 KV, 3-phase Transformer (* 1Lot = Oil for 1 Transformers)
Lot* 2
2.0 Testing & Maintenance Equipments2.1 Oil Storage Tank No. 12.2 Transformer Oil Filtration plant (6KLPH) No 1
3.0 LT TRANSFORMER3.1 315 kVA, 11/0.400kV (Indoor/Outdoor) with Bus disconnector, Power
fuse and all other accessories.Nos 1
3.2 11kV Bus disconnector, Power fuse and all other accessories for above transformer.
Set 1
B 145 kV equipment1.0 145KV GIS Equipment1.1 145kV, SF6 GIS Bus Bars Module [ Module description as per
Technical Project specification]Set 2
1.2 145kV, SF6 GIS ICT bay Module [ Module description as per Technical Project specification]
Set 2
1.3 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification]
Set 4
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 2 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
1.4 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification] (Optional)
Set 2
1.5 145kV, SF6 GIS Bus Coupler bay Module [ Module description as per Technical Project specification]
Set 1
1.6 145kV, 1250A, 31.5kA SF6/Air Bushing for Connecting GIS to AIS alongwith support structure
Nos 12
1.7 145kV, 1250A, 31.50kA SF6/Air Bushing for Connecting GIS to Transformer alongwith support arrangement
Nos 6
1.8145kV, 1250A, 1phase SF6 GIS Bus duct alongwith support structure
OPTION-I2000A, 31.5kA for 1 sec. Single Phase Mtr. 600
OPTION-II2000A, 31.5kA, 1sec three phase Mtr. 200Note : Bidder is required to quote for either option-I or Option-II
1.9 Testing & Maintenance Equipment for GIS1.9.1 Partial Discharge Monitoring System for 145kV GIS System as per
Technical Specification, GISSet 1
1.9.2 Dew Point meter for 145kV GIS System Set 11.9.3 SF6 Gas Leak Detector for 145kV GIS System Set 11.9.4 EOT crane for 145kV GIS Hall Set 11.9.5 SF6 Gas Analyser Set 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 3 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
B2 145KV Outdoor Equipment1.0 145 kV Surge Arrestors 1.1 120 kV Surge Arrestors (1- Phase) Nos 182.0 145 kV Post insulators, as required Nos 18
C RELAY PANELS (WITH AUTOMATION)1.0 132 kV 1.1 Line Control & Protection Panel with distance relay / Differential relay Set 6
1.2 Current Differential Relay for other end of line Nos 4
1.3 Transformer Control & Protection Panel (For HV side) Set 21.4 Bus Bar Protection Panel Set 1
D MV Switchgear1.0 11 kV Indoor VCB Switchgear1.1 11kV 2500A Incomer Set 21.2 11kV 1250A Outgoing Set 101.3 11kV 2500A Buscoupler Set 11.4 11kV 2500A Trunking Set 1
For Mulpani Switching Station1.5 11kV Incomer / Ring main with necessary adaptation with existing bay
2
2.0 Surge arrestors with accessories for 11 kV Line Nos 18
E COMMON EQUIPMENTS1.0 Relay Test tool kit Set 02.0 Time synchronisation equipment No. 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 4 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
F SUBSTATION AUTOMATION Complete Substation Automation System (SAS) for substation including hardware and software for the substation & remote control stations alongwith associated equipments for the following bays as per Technical Specification
1.0 Main bays to be automated1.1 132 kV system Bay Nos 7
1.2 11 kV system Bay Nos 13
1.3 BCU for controlling & monitoring of Auxilary System Set 1
G Teleprotection & communication Equipments 1 PBAX with following configuration as per TS Set 1
1.1 2 wire subscriber interface card with capacity 32 local subscribers or as required (along with 32 nos. Instruments)
1.2 4 wire E & M interface card with capacity 8 nos. trunks (For PLCC or Other communication mode) as required
1.3 E-1 interface with 2 trunks G-7031.4 2 wire interface with 1 trunk (For PSTN)2 Testing & Maintenance equipment (print test kit only) Set 13 4 wire telephone equipment Lot 1
H LT Switchgear (As per Technical specification)1 415V Main switchboard Set 12 415V ACDB Set 13 415V MLDB Set 14 415V Emergency LDB Set 15 220V DCDB Sets 16 48V DCDB Sets 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 5 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
I Batteries1.0 220V
1.1 600 AH Nos 2J Float Cum Boost Battery Charger
1.0 220V Float Cum Boost Battery Charger 1.1 80A/80A Nos 2
K Fire Protection System1.0 Portable /Trolley/Wheel mounted extinguishers
1.1 9 litre water type Nos 51.2 50 litre foam type Nos 21.3 4.5 kg CO2 type Nos 13
1.4 4.5 kg Dry Chemical Power (DCP) type Nos 52.0 Smoke detection system Set 13.0 Fire detection and Alarm System Set 1
L Cables along with clamps, glands, lugs and straight joints etc.
1.0 Power Cables - (1.1kV grade)1.1 3.5Cx300 sqmm (XLPE) cable for filter Machine along with termination
arrangement as per TSKM 0.3
2.0 Power Cables - (12kV grade)2.2 1Cx800 sqmm (XLPE) copper cable for Incomer with termination
arrangement as per TSKM 1
2.2 3Cx300 sqmm (XLPE) Aluminum cable for outgoing feeders along with termination arrangement as per TS including cable duct pipe for laying outside cable trench to nearest pole.
KM 3
2.3 3Cx300 sqmm (XLPE) Aluminum cable for outgoing ringmain feeders along with termination arrangement as per TS including cable duct pipe to Mulpani Switching Station
KM 6
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 6 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
3.0 Power Cables - (145kV grade)3.1 1Cx500 sqmm (XLPE) copper cable for line bay along with termination
arrangement as per TSKM 1
3.2 1Cx240 sqmm (XLPE) copper cable for Transformer along with termination arrangement as per TS
KM 0.5
Note:Cables are to be used as a option to Bus ducts, if required
M Air conditioning System for Control Building1.0 High wall type split AC unit of 2 TR capacity Nos 15
N Fabrication, galvanising and supply of following Steel Structures including nuts, bolts, all types of washers, packplates, step bolts and gusset plates including foundation bolts.
1.0 Lattice Structure including Foundation Bolts MT 402.0 Pipe Structure including Foundation Bolts . MT 103.0 Fastners and step bolts.(Nuts,Bolts & Washers) MT 5
O Communication equipments 1.0 Transmission equipments
1.0 SDH Equipment ( STM- 4 MADM, upto 3 MSP protected directions)1.1
Base Equipment (Common cards, Cross-connect/control cards, Optical base cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc. fully equipped including Optical interphase/SFPs and Tributary cards for full function with future proviison of communication and protection system.
Set 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 7 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
2.0 Termination Equipment2.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of the system
Set 1
3.0 Equipment Cabinets3.1 For Drop/Insert Multiplexer No. 13.2 For SDH Equipment No. 1
4.0 Main Distribution Frame(100 pairs) No. 1
5.0 BOQ for Auxiliary Power Supply Equipments 5.1 SMPS based 48V DC Power Supply (DCPS) system Nos. 25.2 VRLA type Battery bank for above DCPS system Nos. 2
At Kathmandu LDC
6.0 Termination Equipment6.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of system
Set 1
7.0 Equipment Cabinets7.1 For Drop/Insert Multiplexer No. 1
8.0 Main Distribution Frame(100 pairs) No. 1
Sub-Total Part-A
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 8 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Part-B: CONTRACTOR ASSESSED QUANTITIESA Erection Hardware
Insulator strings, Disc Insulators, Hardware, conductor, Al tube, bus-bar materials, cable trays, clamps, spacers, connectors including equipment connectors, Junction box, earthwire, buried cable trenches/pipe equipment & lighting, all accessories etc. for the following:
1.0 145kV GIS Termination Arrangement:1.1 Line Bay Set 41.2 Transformer Bay Set 2
2.0 Earthing and lightning protection including necesaary connectors/connections, risers etc. complete in all respect( but excluding LM structures for Lightning protection)
2.1 Earth Conductor (copper) LS 12.2 Earth Rod (copper clad steel) LS 12.3 Equipment for lightning protection LS 1
B Fire Protection System1.0 Fire Protection system with complete U/G & O/G piping, Tanks, building
and accessories etc. complete for Indoor Transformer: Transformer Set 2
1.1 132/11 KV, 3-phase Transformer
C Illumination System1.0 Control Building cum administrative building LS 12.0 Switchyard lighting Outdoor LS 13.0 Street lighting LS 14.0 Security Room LS 15.0 Car parkings LS 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 9 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
D Air conditioning & ventilation System 1.0 Air conditioning 1.1 Panel room in 145kV GIS Hall LS 1
2.0 Ventilation system 2.1 145KV GIS hall LS 1
E POWER & CONTROL CABLES1.0 Power Cables(PVC)- (1.1kV grade) LS 12.0 Power Cables (XLPE)(excluding 3.5Cx300 sqmm (XLPE) cable for filter
Machine)- (1.1kV grade)LS 1
3.0 Control Cable (PVC)- (1.1kV grade) LS 14.0
Cable glands, lugs & straight through joints for Power & Control cablesLS 1
F
Integration of all 132/22/11kV Bays under present scope with the SCADA of SIEMENS (SINAUT Spectrum) at Load Dispatch Centre, Kathmandu including supply of Hardware, Software, accessories etc. as per TS Section Project.
LS 1
Sub-Total Part-B
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 10 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
Part-C: Mandatory Spares
(I) Mandatory Spare List for TransformerFor 132/11 KV, 3-phase Transformer
1.0 Strarters, contactors,switches & Relays for Electrical control panels(One set of each type)
Set 1
2.0 Spare insulating oil to be handed over to Owner after commisioning for O&M requirement
KL 10
(II) SPARES FOR 145kV GIS
1.0 General
1.1Covers with all accessories necessary to close a compartment in case ofdismantling of any part of the Enclosure to ensure the sealing of thiscompartment
1.1.1 For 3 Phase Enclosure if applicable Nos. 1
1.1.2 For Single phase enclosure if applicable Nos. 1
1.2Locking device to keep the Dis-connectors (Isolators) and Earthingswitches in close or open position in case of removal of the drivingMechanism
Sets 1
2.0 145 KV SF6 CIRCUIT BREAKER:
2.1 Trip coil assembly with resistor as applicable Sets 1
2.2 Closing coil assembly with resistor as applicable . Sets 1
2.3Relays, Power contactors, push buttons, timers & MCBs etc (1 No. ofeach type & rating)
Sets 1
2.4 Closing coil assembly (including valve, if applicable) Sets 1
2.5 Trip coil assembly (including valve, if applicable) Sets 1
2.6 Auxiliary switch assembly of each type Sets 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 11 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
3.0 145 KV ISOLATORS :
3.1 Push button switch - (1 No. of each type & rating) as applicable Sets 1
3.2 Limit switch and Aux. Switches for complete 3 phase equipment 3.3 For isolator Sets 1
3.4 For earth switch Sets 1
3.0 120kV SA3.1 Complete LA No. 13.2 Surge counter/monitor Nos. 1
(II) SAS1.0 Bay Control Unit (IED) of each type Set 12.0 Ethernet Switch of each type Set 1
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 1 PART 3 PAGE 12 OF 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation FC: Foreign Currency
Schedule No.1: Plant and Equipment including Mandatory Spares to be supplied from abroad LC: Local Currency
Country of origin
Total Amount (Excluding Taxes and
Duties)
Custom, VAT and other taxes
FC LC
Currency# Unit Rate Amount
1.0 2 3 4 5 6 7 8 = (7) x (5) 9=8 10
NEPAL ELECTRICITY AUTHORITY
Item No. Item description
Estimated CIP Project Site including insurance, clearing,
forwarding and transportation to site (Excluding Taxes and Duties applicable in Nepal)
Unit
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
QuantityFC
(III) 11 kV Switchgear1 11kV Vacuum Interrupter for Incomer and Outgoing No 32 Tripping Coils Nos 33 Closing Coils Nos 34 Spring Charging Motor Set 15 Protection Relays
5.1 3 phase Overcurrent Relay, for 11kV side one of each type Nos 15.2 Ground Fault Relay, for 11kV side, oe of each type Nos 16 Ammeter, Nos one of each rating Nos 17 Voltmeter, Nos Nos 18 kVA Meter, each Nos 19 CTs as in Outgoing Feeder Set 110 Operating Handle Nos 111 Indicating lamps (100% of used), Lot Lot 1
Sub-Total Part-CTotal For PART 3 Jorpati (Mulpani) Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 1 ( Total of column 9 to be carried forward to Schdule 5: Grand Summary)Note : 1) Bidder is required to quote prices in this Schedule for all the individual items/sub-items.
* Strike-out whichever is not applicable.
Name of Bidder: Date:
Signature of Bidder:
(Printed Name)
(Designation)
(Common Seal)
2.) The Prices of equipments are inclusive of type test charges.
3.) BOQ given above is indicative only based on the scope of work as given in Employer's Requirements. The quantities mentioned above may undergo change during detailed engineering to meet the functional requirement and scope of work defined in Employer's Requirements.
Specify currency in accordance with BDS ITB Clause 32.1, Part-I of the Bidding Documents.
Name of Bidder: Signature of Bidder:
SPECIFICATION NO.: SCHEDULE - 2 PART 1 PAGE 13 OF 29
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No.2: Plant and Equipment including Mandatory Spares Parts to be supplied from within Nepal LC: Local Currency (ALL Price in Local Currency)
Total Amount (Excluding Taxes
)
Custom, VAT and
other taxes
Unit Rate Amount Unit Rate Amount
1 2 3 4 5 6 = (4) x (5) 7 8=(4)x(7) 9=6+8 10
PART 3 132/11 kV Jorpati (Mulpani) Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIES
Part-B: CONTRACTOR ASSESSED QUANTITIES
Part-C: Mandatory Spares
Total For PART 3 Jorpati (Mulpani) Substation [(Part-A+ Part-B+ Part C)]Total for Schedule 2 (Total of column 9 to be carried forward to Schdule 5: Grand Summary)
Note : 1) Bidder is required to quote prices in this Schedule for all the items in Schedule 1 which they wish to supply from within Nepal.
# Specify currency in accordance with BDS ITB Clause 32.1, Part-I of the Bidding Documents.* Strike-out whichever is not applicable.
a Specify currency in accordance with ITB 19.1 of the BDS.
Name of Bidder: Date:
Signature of Bidder: (Printed Name) (Designation)
(Common Seal)
Ex Faxtory Price (Excluding VAT) in LC
Inland transportation to site in LC
b Column 5 Price shall include all customs duties and sales and other taxes already paid or payable on the components and raw materials used in the manufacture or assembly of the item or the
customs duties and sales and other taxes already paid on previously imported items.
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Item No. Item description Unit Quantity
2.) The Prices of equipments are inclusive of type test charges.
Name of Bidder: Package A-2 Signature of Bidder:
SPECIFICATION NO SCHEDULE 3 , PART 1 PAGE 14 of 29
Power Transmission and Distribution Efficiency Enhancement ProjectPMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Local Currency Portion
Foreign Currency Portion
Quantity Unit NRs Currency LC FC1 2 3 4 5 6 7=3x5 8=3x6
PART 3132/11 kV Jorpati (Mulpani) Substation (132V GIS & Indoor)
Not Applicable
Total for Schedule 3 (Total of column 7 & 8 to be carried forward to Schdule 5: Grand Summary)
NOTE: The design cost is included in schedule 1.
Name of Bidder: Date:Signature of Bidder: (Printed Name) (Designation) (Common Seal)
Schedule A-3: Design Services
NEPAL ELECTRICITY AUTHORITY
Item No. Item DescriptionEstimated
Unit Prices Total Prices
PROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Name of Bidder PACKAGE A2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 15 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
PART 3 132/11 kV Jorpati (Mulpani) Substation (132V GIS & Indoor)
Part-A : EMPLOYER ASSESSED QUANTITIES
A POWER TRANSFORMER
1.0 POWER TRANSFORMER1.1 31.5/45 MVA , 132/11 KV, 3-phase Indoor Transformer (Excluding insulating oil) Nos. 2
1.2 Insulating oil for 31.5/45 MVA , 132/11 KV, 3-phase Transformer (* 1Lot = Oil for 1 Transformers)
Lot* 2
2 LT TRANSFORMER2.1 315 kVA, 11/0.400kV (Indoor/Outdoor) with Bus disconnector, Power fuse and all
other accessories.Nos 1
2.2 11kV Bus disconnector, Power fuse and all other accessories for above transformer. Set 1
B 145 kV equipment1 145KV GIS Equipment
1.1 145kV, SF6 GIS Bus Bars Module [ Module description as per Technical Project specification]
Set 2
1.2 145kV, SF6 GIS ICT bay Module [ Module description as per Technical Project specification]
Set 2
1.3 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification]
Set 4
1.4 145kV, SF6 GIS Line bay Module [ Module description as per Technical Projet specification] (Optional)
Set 2
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 16 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
1.5 145kV, SF6 GIS Bus Coupler bay Module [ Module description as per Technical Project specification]
Set 1
1.6 145kV, 1250A, 31.5kA SF6/Air Bushing for Connecting GIS to AIS alongwith support structure (Single Phase)
Nos 12
1.7 145kV, 1250A, 31.50kA SF6/Air Bushing for Connecting GIS to Transformer alongwith support arrangement (Single Phase)
Nos 6
1.8 245kV, 1600A, 1phase SF6 GIS Bus duct alongwith support structureOPTION-I2000A, 40kA for 1 sec. Single Phase Mtr. 600
OPTION-II2000A, 40kA, 1sec three phase Mtr. 200Note : Bidder is required to quote for either option-I or Option-II
1.9 Testing & Maintenance Equipment for GIS1.9.1 Partial Discharge Monitoring System for 145kV GIS System as per Technical
Specification, GIS
Set 1
1.9.2 EOT crane for 245kV GIS Hall Set 1
2.0 145KV Outdoor Equipment2.1 145 kV Surge Arrestors
2.1.1 120 kV Surge Arrestors (1- Phase) Nos 182.2 145 kV Post insulators, as required Nos 18
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 17 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
C RELAY PANELS (WITH AUTOMATION)1.0 132 kV 1.1 Line Protection Panel with distance relay / Differential relay Set 61.2 Current Differential Relay for other end of line Nos 41.3 Transformer Protection Panel (For HV side) Set 21.4 Bus Bar Protection Panel Set 1
D MV Switchgear1.0 11 kV Indoor VCB Switchgear1.1 11kV 2500A Incomer Set 21.2 11kV 1250A Outgoing Set 101.3 11kV 2500A Buscoupler Set 11.4 11kV 2500A Trunking Set 1
For Mulpani Switching Statione 11kV Incomer / Ring main with necessary adaptation with existing bay 2
2 Surge arrestors with accessories for 11 kV Line Nos 18
E COMMON EQUIPMENTS
1.0 Special Relay Test Tool kit No 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 18 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
F SUBSTATION AUTOMATION Complete Substation Automation System (SAS) for substation including hardware and software for the substation & remote control stations alongwith associated equipments for the following bays as per Technical Specification
1.0 Main bays to be automated1.1 132 kV system Bay Nos 71.2 11 kV system Bay Nos 131.3 BCU for controlling & monitoring of Auxilary System Set 1
G Teleprotection & communication Equipments 1 PBAX with following configuration as per TS Set 1
1.1 2 wire subscriber interface card with capacity 32 local subscribers or as required (along with 32 nos. Instruments)
1.2 4 wire E & M interface card with capacity 8 nos. trunks (For PLCC or Other communication mode) as required
1.3 E-1 interface with 2 trunks G-7031.4 2 wire interface with 1 trunk (For PSTN)2 Testing & Maintenance equipment (print test kit only) Set 13 4 wire telephone equipment Lot 1
H LT Switchgear (As per Technical specification)1 415V Main switchboard Set 12 415V ACDB Set 13 415V MLDB Set 14 415V Emergency LDB Set 15 220V DCDB Sets 16 48V DCDB Sets 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 19 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
I Batteries1 220V
1.1 600 AH Nos 2
J Float Cum Boost Battery Charger
1 220V Float Cum Boost Battery Charger
1.1 80A/80A Nos 2
K Fire Protection System1 Portable /Trolley/Wheel mounted extinguishers
1.1 9 litre water type Nos 51.2 50 litre foam type Nos 21.3 4.5 kg CO2 type Nos 13
1.4 4.5 kg Dry Chemical Power (DCP) type Nos 52 Smoke detection system Set 13 Fire detection and Alarm System Set 1
L Cables along with clamps, glands, lugs and straight joints etc.1 Power Cables - (1.1kV grade)
1.1 3.5Cx300 sqmm (XLPE) cable for filter Machine along with termination arrangement as per TS
KM 0.3
2 Power Cables - (12kV grade)2.1 1Cx800 sqmm (XLPE) copper cable for Incomer with termination arrangement as per
TSKM 1
2.2 3Cx300 sqmm (XLPE) Aluminum cable for outgoing feeders along with termination arrangement as per TS including cable duct pipe for laying outside cable trench to nearest pole.
KM 3
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 20 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
2.3 3Cx300 sqmm (XLPE) Aluminum cable for outgoing ringmain feeders along with termination arrangement as per TS including cable duct pipe to Mulpani Switching Station
KM 6
3 Power Cables - (145kV grade)3.1 1Cx500 sqmm (XLPE) copper cable for line along with termination arrangement as
per TSKM 1
3.2 1Cx240 sqmm (XLPE) copper cable for Transformer along with termination arrangement as per TS
KM 0.5
Note:Cables are to be used as a option to Bus ducts, if required
M Air conditioning System for Control building1 High wall type split AC unit of 2 TR capacity Nos 15
N Fabrication, galvanising and supply of following Steel Structures including nuts, bolts, all types of washers, packplates, step bolts and gusset plates including foundation bolts.
1.0 Lattice Structure including Foundation Bolts MT 402.0 Pipe Structure including Foundation Bolts . MT 103.0 Fastners and step bolts.(Nuts,Bolts & Washers) MT 5
O Communication equipments 1 Transmission equipments
1 SDH Equipment ( STM- 4 MADM, upto 3 MSP protected directions)1.1 Base Equipment (Common cards, Cross-connect/control cards, Optical base cards,
Power supply cards, power cabling, other hardware & accessories including sub-racks, patch cords, DDF etc. fully equipped including Optical interphase/SFPs and Tributary cards for full function with future proviison of communication and protection system.
Set 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 21 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 22 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
2 Termination Equipment2.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of the system
Set 1
3 Equipment Cabinets3.1 For Drop/Insert Multiplexer No. 13.2 For SDH Equipment No. 1
4 Main Distribution Frame(100 pairs) No. 1
5 BOQ for Auxiliary Power Supply Equipments 5.1 SMPS based 48V DC Power Supply (DCPS) system Nos. 15.2 VRLA type Battery bank for above DCPS system Nos. 1
At Kathmandu LDC
6 Termination Equipment6.1 Drop/Insert Multiplexer
Base Equipment (Common cards, Power supply cards, power cabling, other hardware & accessories including sub-racks, etc. fully equipped including subscriber line interface cards & accessories) for full functioning of system
Set 1
7 Equipment Cabinets7.1 For Drop/Insert Multiplexer No. 1
8 Main Distribution Frame(100 pairs) No. 1
Sub-Total Part-A
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 23 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
Part-B: CONTRACTOR ASSESSED QUANTITIES
A Erection HardwareInsulator strings, Disc Insulators, Hardware, conductor, Al tube, bus-bar materials, cable trays, clamps, spacers, connectors including equipment connectors, Junction box, earthwire, buried cable trenches/pipe equipment & lighting, all accessories etc. for the following:
1.0 145kV GIS Termination Arrangement:1.1 Line Bay Set 41.2 Transformer Bay Set 2
2.0 Earthing and lightning protection including necesaary connectors/connections, risers etc. complete in all respect( but excluding LM structures for Lightning protection)
2.1 Earth Conductor (copper) LS 12.2 Earth Rod (copper clad steel) LS 12.3 Equipment for lightning protection LS 1
B Fire Protection System1 Fire Protection system with complete U/G & O/G piping, Tanks, building and
accessories etc. complete for Indoor Transformer: Transformer Set 2
1.1 132/11 KV, 3-phase Transformer
C Illumination System1 Control Building cum administrative building illumination LS 12 Switchyard lighting Outdoor LS 13 Street lighting LS 14 Security Room LS 15 Car parkings LS 1
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 24 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
D Air conditioning & ventilation System 1.0 Air conditioning system 1.1 Panel room in 145kV GIS Hall LS 1
2.0 Ventilation system 2.1 145KV GIS hall LS 1
E POWER & CONTROL CABLES1 Power Cables(PVC)- (1.1kV grade) LS 12 Power Cables (XLPE)(excluding 3.5Cx300 sqmm (XLPE) cable for filter Machine)-
(1.1kV grade)LS 1
3.0 Control Cable (PVC)- (1.1kV grade) LS 1
4 Cable glands, lugs & straight through joints for Power & Control cables LS 1
FIntegration of all 132/11kV Bays under present scope with the SCADA of SIEMENS (SINAUT Spectrum) at Load Dispatch Centre, Kathmandu including supply of Hardware, Software, accessories etc. as per TS Section Project.
LS 1
Sub-Total Part-B
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 25 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
PART-C: Civil Works (As per technical specification)
1.0 Excavation in all types of soil and rock including backfilling disposal etc. for all leads
and lifts Lot 1
2.0 Providing and laying of Plain Cement Concrete (PCC) (1:4:8) Cu.Mtr. 1000
3.0 Providing and laying of Plain Cement Concrete (PCC) (1:2:4) Cu.Mtr. 300
4.0 Providing and laying of Reinforced Cement Concrete Design Mix (M25)
including pre cast, shuttering, Grouting of pockets & underpinning but
excluding steel reinforcement.
Cu.Mtr. 2000
5.0 Providing and laying Plain Cement Concrete 1:5:10 (1 cement : 5 sand : 10
Stone aggregate)Cu.Mtr. 500
6.0 Steel Reinforcement (Fe 500) MT 200
7.0 Miscellaneous Structural steel used for rails , plates for rail fixing, ,gratings,
gratings supports etc for transformer /reactor foundation,cable supportstand
earthing cleats ,chequered plates, embedments, edge protection angles for
cable trenches but excluding the reinforcement steel and steel for lattice and
pipe structures which shall be paid seperately.
MT 30
8.0 Stone filling (40mm) over grating of Transformer /reactor Foundation Cu.Mtr. 40
9.0
Stone spreading including antiweed treatment in switchyard but excluding
PCC.Sq. Mtr. 2000
10.0
Supplying & laying hume pipe with collars of grade (NP-3) but excluding
concrete of bed/support/encasing of hume pipes which shall be paid
seperatelyunder respective items of BPS
10.1 250mm dia RM 150
10.2 300mm dia RM 120
10.3 450mm dia RM 80
10.4 600mm dia RM 40
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 26 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
11.0 Concrete road as per technical specification and approved drawing but
excluding reinforcement & concrete which shall be paid seperately under
respective items of BPS11.1 Concrete Road 4m wide Sq. m. 400
12.0
Construction of rail-cum-raod as per technical specification and approved
drawing including all items such as excavation, compaction, rolling, watering,
WBM, etc but excluding concrete, reinforcement and structural steel which
shall be paid seperately under respective items of BPS
12.1 Section having two rails Sq. m. 100
13.0
Chain link Switchyard fencing as per technical specification and approved
drawing but excluding concrete which shall be paid seperately under
respective items of BPS
RM 260
14.0
Switch yard Gate excluding concrete which shall be paid seperately under
respective items of BPS
Nos.2
15.0 All civil works for construction of drains as per technical specification and
approved drawing excluding concrete which shall be paid seperately under
respective items of BPS15.1 Type AA (300mm wide x Depth up to 600mm) RM 500
15.2 Type BB (450 wide x Depth From 600 to 900mm) RM 200
15.3 Type CC (600 wide x Depth From 900 to 1200mm) RM 200
15.4 Type DD (750 wide x Depth From 1200 to 1500mm) RM 200
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 27 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
16.0 External water supply as per technical specification from borewell/single
point of water supply within substation boundary to Fire water Tank, control
room Building and other buildings as applicable including all items like
excavation, pipes, fittings, jointings, valves, chambers/manholes etc
16.1 80mm Dia GI Pipe RM 10016.2 50mm dia GI pipe RM 8016.3 40mm dia GI pipe RM 6016.4 25mm Dia GI Pipe RM 40
17.0 External sewerage system including all item such as excavation, piping, pipe
fittings, manholes, gali trap, gali chamber etc.17.1 (i) 250 mm Dia. RM 5017.2 (i) 150 mm Dia. RM 50
18.0 Local Sand filling around and under Foundation as applicable. Cu.Mtr. 30019.0 Stone soling below foundations wherever specified in approved drawings
during detailed engineeringCu.Mtr. 200
20 All civil works as per technical specification and approved drawing
including internal finish but excluding excavation, PCC, RCC, reinforcement
steel and external finishing which shall be paid seperately under respective
items of BPS
20.1 Control room cum administrative building (Double story) as per TS Sq. m. 1200
20.2 Car Parking shed (for 5 cars) LS 1
20.3 Security Room LS 1
21 External finish as per specification for following buildings:
21.1 Control room cum administrative building (Double story) as per TS Sq. m. 1200
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 28 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
21.2 Car Parking shed (for 5 cars) LS 1
21.3 Securty Room LS 1
22Septic tank as per specification and approved design according to International/British standards and soak pit as per approved drawing excluding concrete & reinforcement (For 50 users)
LS 3
23 Geotechnical /Soil Investigation as per technical specification LS 124 Detail Survey and contour mapping of the site LS 1
25 Site levelling25.1 Earth work in cutting & Filling in all types of soils including soft/disintegrated
rockCu.Mtr. 7000
25.2 Earth work in Filling with borrowed earth Cu.Mtr. 5000
26.0
All civil works for Boundary wall including excavation, concrete, reinforcement steel,structural steel, plaster, painting, barbed wire and concertina coil etc all complete asper technical specification (2.5 m high brick masonary wall and 0.5 m high anglesupport on top).
RM 500
27 Construction of retaining wall with random Rubble masonary in cement sand
mortar (1:6) including levelling up with cement concrete (1:6:12),providing
weep holes of PVC pipes (150 mm dia) with necessary filter material at the
mouth of weep holes,50 mm thick cement concrete (1:2:4) copping on the top
of wall, 100 mm thick PCC (1:4:8) below RR masonary work,excavation of
foundation for all lifts up to 3m above lower level . Item of excavation, PCC
(1:2:4 & 1:4:8) shall be measured and paid seperately under respective items of
BPS
Cu. M 6000
Name of Bidder PACKAGE A-2 Signature of Bidder
SPECIFICATION NO: SCHEDULE 4, PART 3 PAGE 29 of 29
Power Transmission and Distribution Efficiency Enhancement Project
PMD/PTDEEP/KTCEP-073/74-01: Design, Supply, Installation and Commissioning of 132kV GIS Substation
Schedule No. 4 : Installation and Other Services(a): Installation and Construction Charges
Currency# Unit Rate Total Charges Unit Rate Total Charges
(1) (2) (3) (4) (5) (6) 7 8 9=8x6 10 11=10x6
NEPAL ELECTRICITY AUTHORITYPROJECT MANAGEMENT DIRECTORATE
Kathmandu Valley Transmission Capacity Reinforcement Project
Qty.Portion in Foreign Currency Portion in Nepalese Currency
(in NPR)
Installation Charges
Item Description
Sl. No.
Country of Origin
Type & Designation
Unit
28.0 Supplying, providing stone work packed in steel wire crats as per design &
drawing to be developed by the contractor for all leads & lifts along the
boundary wall & other places as required.
Cu. M 2000
29.0Approach Road - Construction of 6m wide black top (Bituminous/asphalt)
road with wideblack top pavement and earthen shoulders on either side of
road, Water bound macadum of suitable thickness as per design below
pavement shall be laid as per technical specification.
Sq. m. 0
Sub-Total Part-C
Total For PART 3 Jorpati (Mulpani) Substation [(Part-A+ Part-B+ Part C)]
Total for Schedule 4( Total of column 9 and 11 to be carried forward to Schedule 5: Grand Summary)
# Specify currency in accordance with ITB Clause 12.1 and corresponding BDS clauses,
Vol.I of the Bidding Documents.
Name of Bidder:
Signature of Bidder: (Printed Name) (Designation) (Common Seal)
Name of Bidder PACKAGE A-2 Signature of Bidder