nepal electricity authority · nepal electricity authority (a government of nepal undertaking) ......

Nepal Electricity Authority (A Government of Nepal Undertaking)

Transmission Directorate

NEPAL-INDIA ELECTRICITY TRANSMISSION AND TRADE

PROJECT

Bidding Document

For

Procurement of Plant Design, Supply and Installation of 220/132 kV

Hetauda & Inaruwa Substations

Single Stage-International Competitive

Bidding Procedure

Issued on: ………………….

Issued to: …………………

Invitation for Bids No.: NIETTP/W/ICB-3/SS

ICB No.: NIETTP/W/ICB-3/SS

Employer: Nepal Electricity Authority

Country: Nepal

Volume III of III

Schedule of Rates and Prices

February, 2018

2-1

Table of Contents

Invitation for Bids

Volume I – Bidding Procedures .......................................................................................... 1-1

Section I. Instructions to Bidders .................................................................................... 1-3

Section II. Bid Data Sheet ............................................................................................. 1-33

Section III. Evaluation and Qualification Criteria ....................................................... 1- 39

Section IV. Bidding Forms ........................................................................................... 1-51

Section V. Eligible Countries ....................................................................................... 1-84

Volume II –Employer’s Requirements ............................................................................. 2-1

Section VI. Employer’s Requirements ........................................................................ 2-1

Volume III – Conditions of Contract and Contract Forms ............................................ 3-1

Section VII. General Conditions (GC)............................................................................. 3-3

Section VIII. Particular Conditions............................................................................... 3-84

Section IX. - Contract Forms ........................................................................................ 3-93

2-2

Schedule of Rates and Prices

ICB No: NIETTP/W/ICB-3/SSPrice Schedule No. 1: Plant (including Mandatory Spare Parts) Supplied from abroad

Currency# CIP Boarder

(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)I 220/132kV Hetauda Substation

Part-A: EMPLOYER ASSESSED QUANTITIES$$

ALT TRANSFORMER (Ref. Volume-II,Section-VI, Chapter 7)

1.0 630 kVA,11/0.400 kV 1 No

B 245 kV equipment (Ref. Volume-II,Section-VI, Chapter 3)

1.0 245 kV Bus Post Insulator 86 Nos

C 145 kV equipment (Ref. Volume-II,Section-VI, Chapter 3)

1.0 145 kV Bus post insulators 69 Set

Procurement of Plant Design, Supply and Installation of 220/132kV Hetauda & Inaruwa Substations(Schedule of Rates and Prices)

Bidder's Name & Address:

Sl.No. Item Description Country of

Origin Qty. UnitUnit Price

Total Price

1 of 57

D 11kV, 25kA for 1 sec, Indoor SwitchgearPanel (3-phase) as per TechnicalSpecification

a 11kV Line module/LT Transformer (800A)(IP-1)

5 Nos

b 11kV Transformer incomer module (800A)(IP-2)

1 Nos

c 11kV PT module (IP-3) 1 Nos

ERELAY PANELS (WITH AUTOMATION)(Ref. Volume-II, Section-VI, Chapter 14)

1.0 220 kVa Circuit Breaker Relay Paneli With Auto Reclose 4 Nosii With out Auto Reclose 4 Nosb Line Protection Panel 4 Nos

cTransformer Protection Panel (For bothHV & MV side)

2 Nos

d Bus Bar Protection Panel 1 Nos

2.0 132 kVa Circuit Breaker Relay Paneli With out Auto Reclose 3 Nosb Transformer Protection Panel (For HV) 1 Nos

cAugmentation of existing bus barprotection scheme.(No. of bays asspecified)

3 Nos

3.0 11 kV

aProtection Panel for 132 and 11 kV SideTransformer (as per TS) 1 Nos

b Protection Panel for Line (as per TS) 4 Nos

1 of 57

Price Schedule No. 1: Plant (including Mandatory Spare Parts) Supplied from abroad


(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

F

CONTROL AND RELAY PANELS (WITHOUTAUTOMATION/CONVENTIONAL) (Ref.Volume-II, Section-VI, Chapter 14)

a Duplex Control Panel For :i One Bay 3 Nos

GCOMMON EQUIPMENTS (Ref. Volume-II,Section-VI, Chapter 2 & 14)

1.0 Special Relay Test kit 1 No

HSUBSTATION AUTOMATION (Ref. Volume-II,Section-VI, Chapter 16)

H.1

Complete Substation automation system/Augumentation Substation automationsystem- including hardware and softwarefor the substation & remote controlstations alongwith associated equipmentsas per Technical Specification.

a Main bays to be automatedi 220 kV system 8 Bay Nosii 132 kV System 3 Bay Nos

2 of 57

ii 132 kV System 3 Bay Nosiii 11kV HT indoor switchgear 1 Set

ILT Switchgear (Ref. Volume-II, Section-VI,Chapter 4)

a 400V Main switchboard 1 Setb 400V ACDB 1 Setc 400V MLDB 1 Setd 400V Emergency LDB 1 Sete 220V DCDB 2 Set

f400A MCCB I No. along with mountingwiring, accessories etc.

1 Set

g 48/50V DCDB (Extn.) Panel as per TS 1 Set

JBatteries (Ref. Volume-II, Section-VI,Chapter 5)

a 220Vi 600 AH 2 Nos

KFloat Cum Boost Battery Charger (Ref.Volume-II, Section-VI, Chapter 5)

a 220V Float Cum Boost Battery Chargeri 80A/80A 2 Nos

LCables along with clamps, glands, lugsand straight joints etc. (Ref. Volume-II,Section-VI, Chapter 9)

a 11kV HT Cable alongwith accessories 0.5 KM

b Power Cables - (1.1kV grade)

i3.5Cx300 sqmm (XLPE) cable forinterconnection of New LT SwitchgearMain Switchboard & Existing ACDB

1 KM

2 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

ii3.5Cx300 sqmm (XLPE) cable for filterMachine along with terminationarrangement as per TS

1 KM

c 11kV HT cablei 1CX630Sqmm 1500 Mtrsii 1CX300sqmm 3000 Mtrsiii 11kV HT cable termination alongwith

accessories & jointing kit12 set

MAir conditioning System for Control roomcum administrative building (Ref. Volume-II, Section-VI, Chapter 10)

aHigh wall type split AC unit of 2 TR capacity

4 Nos

Sub-Total Part-A

Part-B : CONTRACTOR ASSESSEDQUANTITIES $$$

A Erection Hardware (Ref. Volume-II, Section-VI, Chapter 11)Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors including equipmentconnectors, Junction box, earthwire,buried cable trenches/pipe equipment &lighting, all accessories etc. for thefollowing:

3 of 57

Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors including equipmentconnectors, Junction box, earthwire,buried cable trenches/pipe equipment &lighting, all accessories etc. for thefollowing:

a 11kV HT indoor switchgear 1 Set

BIllumination System (Ref. Volume-II,Section-VI, Chapter 6)

aAuxiliary or Exisiting Control Room Building

1 LS

b Switchyard lighting 1 LSc Street lighting 1 LS

CSUBSTATION AUTOMATION (Ref.Volume-II, Section-VI,Chapter 16)

a

Integration of all 220/132/33kV Baysunder present scope with the SCADA ofSIEMENS (SINAUT Spectrum) at LoadDispatch Centre, Kathmandu includingsupply of Hardware, Software, accessoriesetc. as per TS Section Project.

1 LS

DPOWER & CONTROL CABLES (Ref. Volume-II, Section-VI,Chapter 9)

a Power Cables(PVC)- (1.1kV grade) 1 LSb Power Cables (XLPE)- (1.1kV grade) 1 LSc Control Cable (PVC)- (1.1kV grade) 1 LS

3 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

dCable glands, lugs & straight through jointsfor Power & Control cables

1 LS

Sub-Total Part-B

Part-C: Mandatory Spares( Ref. Volume-II, Section-VI, Chapter - 1 ProjectSpecification Requirement, Annexure –IBill of Quantity for Mandatory Spares)

i C&R PANELS 1 LSii DIGITAL PROTECTION COUPLER 1 LSiii SAS 1 LSiv BATTERY CHARGER( 220V) 1 LSv BATTERY CHARGER( 48V) 1 LSvi COMMON SPARES 1 LS

Sub-Total Part-C

Sub Total (I) for 220/132kV HetaudaSubstation

II 220/132/33kV Inaruwa SubstationPart-A: EMPLOYER ASSESSED QUANTITIES$$

4 of 57

Part-A: EMPLOYER ASSESSED QUANTITIES$$


1.0 630 kVA,33/0.400kV 2 No

B145kV equipment (Ref. Volume II, Section-VI, Chapter 3

1.0 Bus post insulators 96 Set

C36 kV equipment (Ref. Volume-II, Section-VI, Chapter 3)

1.0 36kV Horn Gap Fuse (3-Phase) 2 Nos

2.0 33 kV Bus post insulators 6 Nos

DRELAY PANELS (WITH AUTOMATION)(Ref. Volume-II, Section-VI, Chapter 14)

1 220 kVa Circuit Breaker Relay Paneli With Auto Reclose 2 Nosii With out Auto Reclose 6 Nosb Line Protection Panel 2 Nos


4 Nos


2 132 kVa Circuit Breaker Relay Paneli With Auto Reclose 4 Nos.

4 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

ii With out Auto Reclose 5 Nos.b Line Protection Panel 4 Nos.c Reactor Protection Panel 1 Nos.d Shunt Capacitor Protection Panel 1 Nos.e Bus Bar Protection Panel 1 Nos.

3.0 33 kV

aProtection Panel for 33kV SideTransformer (as per TS)

2 Nos

b Protection Panel for Line (as per TS) 6 Nosc Protection Panel for Bus Sectionalizer 1 Nos

ECOMMON EQUIPMENTS (Ref. Volume-II,Section-VI, Chapter 14)


FSUBSTATION AUTOMATION (Ref. Volume-II, Section-VI, Chapter 16)

F.1


5 of 57

F.1


a Main bays to be automatedi 220 kV system 8 Bay Nosii 132 kV System 9 Bay Nosiii 33kV system 9 Bay Nos

GDPC & PABX (Ref. Volume-II, Section-VI,Chapter 15)

a Digital Protection Coupler 10 Nos

bPBAX with following configuration as perTS

1 Set

i)2 wire subscriber interface card withcapacity 32 local subscribers (along with 32nos. Instruments)

ii)4 wire E & M interface card with capacity 8nos. trunks

iii) E-1 interface with 2 trunks G-703iv) 2 wire interface with 1 trunk (For PSTN)

cTesting & Maintenance equipment (printtest kit only)

1 Set

d 4 wire telephone equipment 1 Nos

e

Installation of Two nos. DPC each atRupani Substation and Duhabi Substationfor complete teleprotection applications tocomplete the scope of works.

1 LS

H LT Switchgear (Ref. Volume-II, Section-VI,Chapter 4)

a 415V Main switchboard 1 Setb 415V ACDB 1 Setc 415V MLDB 1 Setd 415V Emergency LDB 1 Set

5 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

e 220V DCDB 2 Setf 48/50V DCDB 2 Set

IBatteries (Ref. Volume-II, Section-VI,Chapter 5)

a 220Vi 600 AH 2 Nosb 48Vi 600 AH 2 Nos

JFloat Cum Boost Battery Charger (Ref.Volume-II, Section-VI, Chapter 5)

a 220V Float Cum Boost Battery Chargeri 80A/80A 2 Nosb 48V Float Cum Boost Battery Chargerii 60A/60A 2 Nos

KFire Protection System (Ref. Volume-II,Section-VI, Chapter 8)

aPortable /Trolley/Wheel mountedextinguishers

i 9 litre water type 5 Nosii 50 litre foam type 2 Nosiii 4.5 kg CO2 type 13 Nosiv 4.5 kg Dry Chemical Power (DCP) type 5 Nos

6 of 57

iii 4.5 kg CO2 type 13 Nosiv 4.5 kg Dry Chemical Power (DCP) type 5 Nosb Smoke detection system 1 Setc Fire detection and Alarm System 1 Set


a 33kV HT Cable alongwith accessories 0.3 KMb Power Cables - (1.1kV grade)

i3.5Cx300 sqmm (XLPE) cable for filterMachine along with terminationarrangement as per TS

1 KM

MAir conditioning System for Control roomcum administrative building (Ref. Volume-II, Section-VI, Chapter 10)

a High wall type split AC unit of 2 TR capacity 12 Nos

N

STEEL STRUCTURES (Tower,Gantrystructures& Equipment supportstructures) (Ref. Volume-II, Section-VI,Chapter 12)

N.1PIPE/LATTICE STRUCTURES (Ref. Volume-II, Section-VI, Chapter 12)

aM.S Structural steel including FoundationBolts complete. 523 MT

b Fastners.(Nuts,Bolts & Washers) 15 MT

OTransmission Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)

O.1SDH Equipment ( STM - 1 upgradable toSTM-4 ADM, upto two directions)

6 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

a

Base Equipment (Common cards, Cross-connect/control cards, Optical base card,Power supply cards, power cabling, otherhardware & accessories including sub-racks, patch cords, DDF etc. fully equippedexcluding (b) and (c) below)

1 No.

b Optical Interface/SFP## for

iOptical Line Interface card (to supportminimum 175 kms)*** 2 No.

c Tributary Cards

iE1 Interface card (Minimum 16 interfacesper card ) 2 No.

iiEthernet interfaces 10/100 Mbps withLayer-2 switching (Minimum 4interfaces per card.)

2 No.

PTermination Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)

a

Drop/Insert Multiplexer Base Equipment(Common cards, Power supply cards,power cabling, other hardware &accessories including sub-racks, etc. fullyequipped excluding subscriber lineinterface cards)

2 No.

b Subscriber Line Interface Cards

i2 wire (sub/sub) voice channel cards (min8 channels per card) 2 No.

7 of 57


ii4 wire (E&M) voice channel cards (min 8channels per card)

2 No.

iii Asynchronous Sub Channels data cards(minimum 4 channels per card)

2 No.iv Synchronous data card (NX64kbps) 1 No.

QEquipment Cabinets (Ref. Volume-II,Section-VI, Chapter 16 & 17)

a For Drop/Insert Multiplexer 1 No.b For SDH Equipment 1 No.

RMain Distribution Frame (100 pairs) (Ref.Volume-II, Section-VI, Chapter 16 & 17) 1 No.

S FODP (Ref. Volume-II, Chapter 16 & 17)

aFODP (minimum 48 Fibres) : Indoor Type,rack mounted with FCPC coupling and pigtails

1 No.

TFibre Optic approach cable (Ref. Volume-II, Section-VI, Chapter 17)

a 48 Fibre (DWSM -G.652D) 0.5 Km.

bInstallation hardware set for above 48Fibre, Fibre Optic Approach Cable

0.5 Set ****

Sub-Total Part-A


AErection Hardware (Ref. Volume-II,Section-VI, Chapter 11)

7 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price


a 220 kV Layout (DMT Layout)i Line Bay 4 Setii Transformer Bay 4 Setiii TBC Bay 1 Setiv BC bay 1 Setv Bus work (Three Bays) 4 Setb 132 kV (Double Main Layout)i Line Bay 4 Setii Transformer Bay 2 Setiii BC Bay 1 Setiv Bus work (For one bays) 9 Setv Bus Reactor Bay 1 Setvi Shunt Capacitor Bay 1 Setc 33 kV (Single Main Bus Layout)i Line Bay 6 Setii Transformer Bay 2 Setiii Bus work (For Four bays) 2 Set

8 of 57

iii Bus work (For Four bays) 2 Setiv Sectionalizer 1 Set

d

Earthing and lightning protection includingnecesaary connectors/connections, risersetc. complete in all respect

i Earth Conductor (copper) 1 LSii Earth Rod (copper clad steel) 1 LSiii Equipment for lightning protection 1 LS

BFire Protection System (Ref. Volume-II,Section-VI, Chapter 8)

a

Pumping arrangement for HVW system &hydrant system, complete with all piping,valves, fittings,etc. inside pump house

i 220/132kV (New) Substation 1 Set

bHydrant system, complete U/G piping andaccessories etc. outside the Pump House.


c

HVW spray system, Hydrant system andcomplete U/G & O/G piping andaccessories etc. out side the pump housefor Transformer / Reactor :

c.1 Transformer

i100MVA , 220/132 KV, 3-phaseAutotransformer

2 Sets

ii63MVA , 220/33 KV, 3-phaseAutotransformer 2 Sets

c.2 Bus Reactori 25MVAR/132kV shunt reactor 1 Sets

8 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

CIllumination System (Ref. Volume-II,Section-VI, Chapter 6)

aIllumination System for switchyard panelroom

i 220KV 3 Setsii 132kV 2 Setsiii 33kV 1 Set

bControl room cum administrative buildingillumination 1 LS

c Switchyard lighting 1 LSd Street lighting 1 LS

DAir conditioning System (Ref. Volume-II,Section-VI, Chapter 10)

aAir conditioning for S/Y panel room220/132kV


ESUBSTATION AUTOMATION (Ref.Volume-II, Section-VI, Chapter 16)

a


1 LS

9 of 57

a


1 LS

FPOWER & CONTROL CABLES (Ref. Volume-II, Section-VI, Chapter 9)


dCable glands, lugs & straight through jointsfor Power & Control cables 1 LS

Sub-Total Part-B



Sub-Total Part-C

9 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

Sub Total For (II) 220/132/33kV InaruwaSubstation

IIIKATHMANDU LDC/132 KV DUHABISUBSTATIONPart-A: EMPLOYER ASSESSED QUANTITIES$$

ATransmission Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)

A.1SDH Equipment ( STM - 1 upgradable toSTM-4 ADM, upto two directions)

a

Base Equipment (Common cards, Cross-connect/control cards, Optical base card,Power supply cards, power cabling, otherhardware & accessories including sub-racks, patch cords, DDF etc. fully equippedexcluding (b) and (c) below)

1 No.

b Optical Interface/SFP## fori L1.2 2 No.c Tributary Cards


10 of 57



2 No.

BTermination Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)

a


2 No.



ii2 wire (sub/exchange) voice channel cards(min 8 channels per card) 1 No.

iii4 wire (E&M) voice channel cards (min 8channels per card) 2 No.

ivAsynchronous Sub Channels data cards(minimum 4 channels per card) 2 No.

v Synchronous data card (NX64kbps) 1 No.

CEquipment Cabinets (Ref. Volume-II,Section-VI, Chapter 16 & 17)


DTMN - Craft Terminal for SDH & PDHEquipments (Ref. Volume-II, Section-VI,Chapter 16 & 17)

a Hardware 1 Set**b Software 1 Set**

ESynchronization Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

10 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

GPS clock including all hardware &accessories 1 Set

F Main Distribution Frame (100 pairs) (Ref.Volume-II, Section-VI, Chapter 16 & 17)

1 No.

GTest Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

a SDH Analyser### 1 No.b Handheld 2Mbps BER Tester 1 No.

cEthernet Tester (with dual port, 10/100ports Mbps Ethernet option, layer-1 &layer-2 functionality)

1 No.

Sub-Total Part-APart-B : CONTRACTOR ASSESSEDQUANTITIES $$$Sub-Total Part-B


ATransmission Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)


11 of 57


aCommon cards, Power supply cards,power cabling, other hardware &accessories (each)

1 Set$

b Optical Interface/SFP## fori L1.2 1 No.

iiOptical Line Interface card (to supportminimum 150 kms)*** 1 No.

iiiOptical Line Interface card (to supportminimum 175 kms)*** 1 No.

c Tributary Cards



1 No.


aDrop/Insert Multiplexer Common cards,Power supply cards, power cabling, otherhardware & accessories (each)

1 Set$



ii4 wire (E&M) voice channel cards (min 8channels per card) 1 No.

iiiAsynchronous Sub Channels data cards(minimum 4 channels per card) 1 No.

iv Synchronous data card (NX64kbps) 1 No.

11 of 57



(1) (2) (3) (4) (5) (6) (7) (8) = (4) x(7)



Total Price

C

Pre Connectorized Optical Fiber PatchCords (10 Mtrs) – Pack of Six Patch Cords(Ref. Volume-II, Section-VI, Chapter 16 &17)

1 Set

Sub-Total Part-C

SubTotal (III) For KATHMANDULDC/132KV DUHABI SUBSTATION

Grand Total For (I), (II) & (III)

NOTE

#

##

***

**

****

Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as many columns for ForeignCurrency requirement as there are foreign currencies.

Optical interface/SFP can be provided with Optical base card or Control card with the condition that control card shallnot be equipped with more than one Optical interface/SFP and optical card with not more than two Opticalinterface/SFP. However main and protection channel shall be terminated on separate cardsSuitable Optical Interface Card(s) or any other solution such as SDH equipment with optical amplifier, wavelengthtranslator or higher aggregate bit rate SDH equipment may be offer for the lengths to meet the link budgetrequirements without repeater.Set shall include all required hardware/software for complete TMN –Craft Terminal system as specified in technicalspecificationsOne set of installation hardware shall contain all installation hardware fittings as may be required for 1 km of ApproachFibre Optic cable.

The testing capacity of SDH analyser shall be provided according to offered SDH equipment

12 of 57

****

###

$

$$

$$$

Date:Place:

Common Seal:

One set of installation hardware shall contain all installation hardware fittings as may be required for 1 km of ApproachFibre Optic cable.

Designation:

Signature:Printed Name:


One Set means one of each type of module/unit card etc

Employer assessed quantities are those which are clearly quantifiable as per the scope of the work and are given underthis heading above.

Contractor assessed quantities are those which bidders are required to estimate for the entire execution of the work andshall incorporate in their price schedules

Those equipments under heading KATHMANDU LDC/132 KV DUHABI SUBSTATION shall be used in any of the stationsand same shall be finalized during the detail engineering.

12 of 57

ICB No: NIETTP/W/ICB-3/SSPrice Schedule No. 2: Plant (including Mandatory Spare Parts) Supplied from within Employer's country

(1) (2) (3) (4) (5) (6) = (3) x(5)I 220/132kV Hetauda Substation

Part-A: EMPLOYER ASSESSEDQUANTITIES $$


1.0 630 kVA,11/0.400 kV 1 No





(Schedule of Rates and Prices)

Procurement of Plant Design, Supply and Installation of 220/132kV Hetauda & InaruwaSubstations


Sl.No. Item Description Qty. EXW Unit

Price NRsUnit EXW Total Price NRs

13 of 57


a 11kV Line module/LT Transformer (800A)(IP-1)

5 Nos

b 11kV Transformer incomer module(800A) (IP-2)

1 Nos





2 Nos




3 Nos

3.0 11 kV



13 of 57

Price Schedule No. 2: Plant (including Mandatory Spare Parts) Supplied from within Employer's country

(1) (2) (3) (4) (5) (6) = (3) x(5)



F

CONTROL AND RELAY PANELS(WITHOUTAUTOMATION/CONVENTIONAL) (Ref.Volume-II, Section-VI, Chapter 14)


GCOMMON EQUIPMENTS (Ref. Volume-II, Section-VI, Chapter 2 & 14)


HSUBSTATION AUTOMATION (Ref.Volume-II,Section-VI, Chapter 16)

H.1

Complete Substation automationsystem/ Augumentation Substationautomation system- including hardwareand software for the substation &remote control stations alongwithassociated equipments as per TechnicalSpecification.

a Main bays to be automatedi 220 kV system 8 Bay Nosii 132 kV System 3 Bay Nos

14 of 57

ii 132 kV System 3 Bay Nosiii 11kV HT indoor switchgear 1 Set

ILT Switchgear (Ref. Volume-II, Section-VI, Chapter 4)



1 Set









1 KM

14 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)




1 KM



MAir conditioning System for Controlroom cum administrative building (Ref.Volume-II, Section-VI, Chapter 10)

aHigh wall type split AC unit of 2 TRcapacity

4 Nos

Sub-Total Part-A


A Erection Hardware (Ref. Volume-II,Section-VI, Chapter 11)Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors including equipmentconnectors, Junction box, earthwire,buried cable trenches/pipe equipment &lighting, all accessories etc. for thefollowing:

15 of 57




aAuxiliary or Exisiting Control RoomBuilding 1 LS



a

Integration of all 220/132/33kV Baysunder present scope with the SCADA ofSIEMENS (SINAUT Spectrum) at LoadDispatch Centre, Kathmandu includingsupply of Hardware, Software,accessories etc. as per TS Section Project.

1 LS

DPOWER & CONTROL CABLES (Ref.Volume-II, Section-VI,Chapter 9)


15 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)



dCable glands, lugs & straight throughjoints for Power & Control cables

1 LS

Sub-Total Part-B



Sub-Total Part-C


II 220/132/33kV Inaruwa SubstationPart-A: EMPLOYER ASSESSEDQUANTITIES $$

16 of 57

Part-A: EMPLOYER ASSESSEDQUANTITIES $$


1.0 630 kVA,33/0.400kV 2 No

B145kV equipment (Ref. Volume II,Section-VI, Chapter 3


C36 kV equipment (Ref. Volume-II,Section-VI, Chapter 3)



D RELAY PANELS (WITH AUTOMATION)(Ref. Volume-II, Section-VI, Chapter 14)1 220 kV

a Circuit Breaker Relay Paneli With Auto Reclose 2 Nosii With out Auto Reclose 6 Nosb Line Protection Panel 2 Nos


4 Nos



16 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)




3.0 33 kV


2 Nos


ECOMMON EQUIPMENTS (Ref. Volume-II, Section-VI, Chapter 14)


FSUBSTATION AUTOMATION (Ref.Volume-II, Section-VI, Chapter 16)

F.1


17 of 57

F.1



GDPC & PABX (Ref. Volume-II, Section-VI, Chapter 15)


bPBAX with following configuration as perTS

1 Set

i)2 wire subscriber interface card withcapacity 32 local subscribers (along with32 nos. Instruments)

ii)4 wire E & M interface card with capacity8 nos. trunks


cTesting & Maintenance equipment (printtest kit only)

1 Set


e

Installation of Two nos. DPC each atRupani Substation and Duhabi Substationfor complete teleprotection applicationsto complete the scope of works.

1 LS

HLT Switchgear (Ref. Volume-II, Section-VI, Chapter 4)

a 415V Main switchboard 1 Setb 415V ACDB 1 Set

17 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)



c 415V MLDB 1 Setd 415V Emergency LDB 1 Sete 220V DCDB 2 Setf 48/50V DCDB 2 Set






a Portable /Trolley/Wheel mountedextinguishersi 9 litre water type 5 Nos

18 of 57

i 9 litre water type 5 Nosii 50 litre foam type 2 Nosiii 4.5 kg CO2 type 13 Nosiv 4.5 kg Dry Chemical Power (DCP) type 5 Nosb Smoke detection system 1 Setc Fire detection and Alarm System 1 Set


a 33kV HT Cable alongwith accessories 0.3 KM

bPower Cables - (1.1kV grade)


1 KM

M

Air conditioning System for Controlroom cum administrative building (Ref.Volume-II, Section-VI, Chapter 10)

aHigh wall type split AC unit of 2 TRcapacity 12 Nos

N



18 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)



aM.S Structural steel including FoundationBolts complete. 523 MT


OTransmission Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)


a

Base Equipment (Common cards, Cross-connect/control cards, Optical base card,Power supply cards, power cabling, otherhardware & accessories including sub-racks, patch cords, DDF etc. fullyequipped excluding (b) and (c) below)

1 No.



c Tributary Cards

iE1 Interface card (Minimum 16interfaces per card ) 2 No.


2 No.


19 of 57


a


2 No.


i2 wire (sub/sub) voice channel cards(min 8 channels per card) 2 No.


2 No.

iiiAsynchronous Sub Channels data cards(minimum 4 channels per card)

2 No.

ivSynchronous data card (NX64kbps)

1 No.


a For Drop/Insert Multiplexer 1 No.

bFor SDH Equipment

1 No.

RMain Distribution Frame (100 pairs)(Ref. Volume-II, Section-VI, Chapter 16& 17)

1 No.


aFODP (minimum 48 Fibres) : Indoor Type,rack mounted with FCPC coupling andpig tails

1 No.

TFibre Optic approach cable (Ref.Volume-II, Section-VI, Chapter 17)


19 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)




0.5 Set ****

Sub-Total Part-A


AErection Hardware (Ref. Volume-II,Section-VI, Chapter 11)Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors including equipmentconnectors, Junction box, earthwire,buried cable trenches/pipe equipment &lighting, all accessories etc. for thefollowing:

a 220 kV Layout (DMT Layout)i Line Bay 4 Setii Transformer Bay 4 Setiii TBC Bay 1 Setiv BC bay 1 Setv Bus work (Three Bays) 4 Set

20 of 57

v Bus work (Three Bays) 4 Setb 132 kV (Double Main Layout)i Line Bay 4 Setii Transformer Bay 2 Setiii BC Bay 1 Setiv Bus work (For one bays) 9 Setv Bus Reactor Bay 1 Setvi Shunt Capacitor Bay 1 Setc 33 kV (Single Main Bus Layout)i Line Bay 6 Setii Transformer Bay 2 Setiii Bus work (For Four bays) 2 Setiv Sectionalizer 1 Set

d

Earthing and lightning protectionincluding necesaaryconnectors/connections, risers etc.complete in all respect



a Pumping arrangement for HVW system& hydrant system, complete with alli 220/132kV (New) Substation 1 Set

bHydrant system, complete U/G pipingand accessories etc. outside the PumpHouse.


20 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)



c

HVW spray system, Hydrant system andcomplete U/G & O/G piping andaccessories etc. out side the pump housefor Transformer / Reactor :

c.1 Transformer


2 Sets




aIllumination System for switchyard panelroom


bControl room cum administrativebuilding illumination 1 LS


21 of 57

DAir conditioning System (Ref. Volume-II,Section-VI, Chapter 10)




a Integration of all 220/132/33kV Baysunder present scope with the SCADA of

1 LS

FPOWER & CONTROL CABLES (Ref.Volume-II, Section-VI, Chapter 9)


dCable glands, lugs & straight throughjoints for Power & Control cables 1 LS

Sub-Total Part-B


21 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)




Sub-Total Part-C

Sub Total For (II) 220/132/33kVInaruwa Substation

IIIKATHMANDU LDC/132 KV DUHABISUBSTATIONPart-A: EMPLOYER ASSESSEDQUANTITIES $$

ATransmission Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)


a


1 No.

22 of 57

a


1 No.




2 No.


a

Drop/Insert Multiplexer BaseEquipment (Common cards, Powersupply cards, power cabling, otherhardware & accessories including sub-racks, etc. fully equipped excludingsubscriber line interface cards)

2 No.



ii2 wire (sub/exchange) voice channelcards (min 8 channels per card) 1 No.



v Synchronous data card (NX64kbps) 1 No.C

Equipment Cabinets (Ref. Volume-II,Section-VI, Chapter 16 & 17)

22 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)






E Synchronization Equipment (Ref.Volume-II, Section-VI, Chapter 16 & 17)

GPS clock including all hardware &accessories

1 Set

FMain Distribution Frame (100 pairs)(Ref. Volume-II, Section-VI, Chapter 16& 17)

1 No.




1 No.

Sub-Total Part-APart-B : CONTRACTOR ASSESSEDQUANTITIES $$$

23 of 57


Sub-Total Part-B





1 Set$




c Tributary Cards



1 No.


23 of 57


(1) (2) (3) (4) (5) (6) = (3) x(5)



aDrop/Insert Multiplexer Common cards,Power supply cards, power cabling,other hardware & accessories (each)

1 Set$






C

Pre Connectorized Optical Fiber PatchCords (10 Mtrs) – Pack of Six PatchCords (Ref. Volume-II, Section-VI,Chapter 16 & 17)

1 Set

Sub-Total Part-C

SubTotal (III) For KATHMANDULDC/132KV DUHABI SUBSTATIONGrand Total For (I), (II) & (III)

#Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as manycolumns for Foreign Currency requirement as there are foreign currencies.

Optical interface/SFP can be provided with Optical base card or Control card with the condition that controlcard shall not be equipped with more than one Optical interface/SFP and optical card with not more thantwo Optical interface/SFP. However main and protection channel shall be terminated on separate cards

24 of 57

#

##

***

**

****

###

$

$$

$$$

Date:Place:

Common Seal:

Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as manycolumns for Foreign Currency requirement as there are foreign currencies.

Optical interface/SFP can be provided with Optical base card or Control card with the condition that controlcard shall not be equipped with more than one Optical interface/SFP and optical card with not more thantwo Optical interface/SFP. However main and protection channel shall be terminated on separate cards

Employer assessed quantities are those which are clearly quantifiable as per the scope of the workand are given under this heading above.

Contractor assessed quantities are those which bidders are required to estimate for the entireexecution of the work and shall incorporate in their price schedules

Those equipments under heading KATHMANDU LDC/132 KV DUHABI SUBSTATION shall be used inany of the stations and same shall be finalized during the detail engineering.

Suitable Optical Interface Card(s) or any other solution such as SDH equipment with opticalamplifier, wavelength translator or higher aggregate bit rate SDH equipment may be offer for thelengths to meet the link budget requirements without repeater.Set shall include all required hardware/software for complete TMN –Craft Terminal system asspecified in technical specificationsOne set of installation hardware shall contain all installation hardware fittings as may be requiredfor 1 km of Approach Fibre Optic cable.



24 of 57

Schedule 3

ICB No: NIETTP/W/ICB-3/SS

Price Schedule No. 3: Design Services

Local CurrencyPortion

Foreign CurrencyPortion (optional)

LocalCurrencyPortion

Foreign currencyPortion(optional)

(1) (2) (3) (4) (5) (7)=(4)x(3) (8)=(5)x(3)

Not Applicable

TOTAL

Procurement of Plant Design, Supply and Installation of 220/132kV Hetauda & Inaruwa Substations



The scope of the Contract covers the detail design of the substations as well. The price of the detail design is deemed to have beencovered in the prices of the other schedules. So the contractor shall not be required to show the breakdown of the prices in thisschedule. Accordingly no separate payment be made for the design Services.

Item Description Qty.Unit Price# Total Price#

25 of 57

Not Applicable

Date:Place:

Common Seal:

TOTAL


Designation:

25 of 57

ICB No: NIETTP/W/ICB-3/SSSchedule No. 4. Installation ServicesPart - A: Local Transportation, Insurance and other Incidental services (including port clearance etc.)

ForeignCurrencyPortion




(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

I 220/132kV Hetauda SubstationPart-A: EMPLOYER ASSESSEDQUANTITIES $$


1.0 630 kVA,11/0.400 kV 1 No







Sl.No. Item Description Qty. Unit

Unit Price# Total Price#

26 of 57



a 11kV Line module/LT Transformer(800A) (IP-1)

5 Nos

b 11kV Transformer incomer module(800A) (IP-2)

1 Nos





2 Nos




3 Nos

3.0 11 kV


26 of 57

Schedule No. 4. Installation ServicesPart - A: Local Transportation, Insurance and other Incidental services (including port clearance etc.)





(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)




F

CONTROL AND RELAY PANELS(WITHOUTAUTOMATION/CONVENTIONAL) (Ref.Volume-II, Section-VI, Chapter 14)


GCOMMON EQUIPMENTS (Ref. Volume-II, Section-VI, Chapter 2 & 14)


HSUBSTATION AUTOMATION (Ref.Volume-II,Section-VI, Chapter 16)

H.1


a Main bays to be automated

27 of 57

a Main bays to be automatedi 220 kV system 8 Bay Nosii 132 kV System 3 Bay Nosiii 11kV HT indoor switchgear 1 Set

ILT Switchgear (Ref. Volume-II, Section-VI, Chapter 4)



1 Set









1 KM

27 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)




1 KM




aHigh wall type split AC unit of 2 TRcapacity

4 Nos

Sub-Total Part-A


AErection Hardware (Ref. Volume-II,Section-VI, Chapter 11)Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors includingequipment connectors, Junction box,earthwire, buried cable trenches/pipeequipment & lighting, all accessoriesetc. for the following:

28 of 57

Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors includingequipment connectors, Junction box,earthwire, buried cable trenches/pipeequipment & lighting, all accessoriesetc. for the following:



aAuxiliary or Exisiting Control RoomBuilding 1 LS



a

Integration of all 220/132/33kV Baysunder present scope with the SCADA ofSIEMENS (SINAUT Spectrum) at LoadDispatch Centre, Kathmandu includingsupply of Hardware, Software,accessories etc. as per TS SectionProject.

1 LS

DPOWER & CONTROL CABLES (Ref.Volume-II, Section-VI,Chapter 9)


28 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)



dCable glands, lugs & straight throughjoints for Power & Control cables

1 LS

Sub-Total Part-B



Sub-Total Part-C


II 220/132/33kV Inaruwa Substation

29 of 57

II 220/132/33kV Inaruwa SubstationPart-A: EMPLOYER ASSESSEDQUANTITIES $$


1.0 630 kVA,33/0.400kV 2 No

B145kV equipment (Ref. Volume II,Section-VI, Chapter 3


C36 kV equipment (Ref. Volume-II,Section-VI, Chapter 3)



DRELAY PANELS (WITH AUTOMATION)(Ref. Volume-II, Section-VI, Chapter 14)

1 220 kVa Circuit Breaker Relay Paneli With Auto Reclose 2 Nosii With out Auto Reclose 6 Nosb Line Protection Panel 2 Nos


4 Nos



29 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)




3.0 33 kV


2 Nos


ECOMMON EQUIPMENTS (Ref. Volume-II, Section-VI, Chapter 14)


FSUBSTATION AUTOMATION (Ref.Volume-II, Section-VI, Chapter 16)

F.1


30 of 57

F.1



GDPC & PABX (Ref. Volume-II, Section-VI, Chapter 15)


bPBAX with following configuration asper TS

1 Set

i)2 wire subscriber interface card withcapacity 32 local subscribers (along with32 nos. Instruments)

ii)4 wire E & M interface card withcapacity 8 nos. trunks


cTesting & Maintenance equipment(print test kit only)

1 Set


e

Installation of Two nos. DPC each atRupani Substation and DuhabiSubstation for complete teleprotectionapplications to complete the scope ofworks.

1 LS

H LT Switchgear (Ref. Volume-II, Section-VI, Chapter 4)

a 415V Main switchboard 1 Setb 415V ACDB 1 Setc 415V MLDB 1 Set

30 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)



d 415V Emergency LDB 1 Sete 220V DCDB 2 Setf 48/50V DCDB 2 Set






aPortable /Trolley/Wheel mountedextinguishers

i 9 litre water type 5 Nos

31 of 57

i 9 litre water type 5 Nosii 50 litre foam type 2 Nosiii 4.5 kg CO2 type 13 Nosiv 4.5 kg Dry Chemical Power (DCP) type 5 Nosb Smoke detection system 1 Setc Fire detection and Alarm System 1 Set




1 KM


aHigh wall type split AC unit of 2 TRcapacity 12 Nos

N



aM.S Structural steel includingFoundation Bolts complete. 523 MT


OTransmission Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

31 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)




a

Base Equipment (Common cards, Cross-connect/control cards, Optical basecard, Power supply cards, powercabling, other hardware & accessoriesincluding sub-racks, patch cords, DDFetc. fully equipped excluding (b) and (c)below)

1 No.



c Tributary Cards



2 No.

PTermination Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

a


2 No.

32 of 57

a


2 No.




2 No.

iii Asynchronous Sub Channels data cards(minimum 4 channels per card)

2 No.iv Synchronous data card (NX64kbps) 1 No.



RMain Distribution Frame (100 pairs)(Ref. Volume-II, Section-VI, Chapter 16& 17)

1 No.


aFODP (minimum 48 Fibres) : IndoorType, rack mounted with FCPC couplingand pig tails

1 No.

TFibre Optic approach cable (Ref.Volume-II, Section-VI, Chapter 17)



0.5 Set ****

Sub-Total Part-A


AErection Hardware (Ref. Volume-II,Section-VI, Chapter 11)

32 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)



Insulator strings, Disc Insulators,Hardware, conductor, Al tube, bus-barmaterials, cable trays, Bay MB, clamps,spacers, connectors includingequipment connectors, Junction box,earthwire, buried cable trenches/pipeequipment & lighting, all accessoriesetc. for the following:

a 220 kV Layout (DMT Layout)i Line Bay 4 Setii Transformer Bay 4 Setiii TBC Bay 1 Setiv BC bay 1 Setv Bus work (Three Bays) 4 Setb 132 kV (Double Main Layout)i Line Bay 4 Setii Transformer Bay 2 Setiii BC Bay 1 Setiv Bus work (For one bays) 9 Setv Bus Reactor Bay 1 Setvi Shunt Capacitor Bay 1 Setc 33 kV (Single Main Bus Layout)i Line Bay 6 Setii Transformer Bay 2 Set

33 of 57

ii Transformer Bay 2 Setiii Bus work (For Four bays) 2 Setiv Sectionalizer 1 Set

d

Earthing and lightning protectionincluding necesaaryconnectors/connections, risers etc.complete in all respect



a

Pumping arrangement for HVW system& hydrant system, complete with allpiping, valves, fittings,etc. inside pumphouse


bHydrant system, complete U/G pipingand accessories etc. outside the PumpHouse.


c

HVW spray system, Hydrant system andcomplete U/G & O/G piping andaccessories etc. out side the pumphouse for Transformer / Reactor :

c.1 Transformer


2 Sets



33 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)




aIllumination System for switchyardpanel room


bControl room cum administrativebuilding illumination 1 LS


DAir conditioning System (Ref. Volume-II, Section-VI, Chapter 10)


Set



34 of 57


a

Integration of all 220/132/33kV Baysunder present scope with the SCADA ofSIEMENS (SINAUT Spectrum) at LoadDispatch Centre, Kathmandu includingsupply of Hardware, Software,accessories etc. as per TS SectionProject.

1 LS

FPOWER & CONTROL CABLES (Ref.Volume-II, Section-VI, Chapter 9)


dCable glands, lugs & straight throughjoints for Power & Control cables 1 LS

Sub-Total Part-B



Sub-Total Part-C

34 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)



Part-D: Shifting of equiment of Inaruwastored at Dhalkebar( Ref. Volume-II,Section-VI, Chapter - 1 ProjectSpecification Requirement, Annexure–IX List of equipment handed over tocontractor)

1 LS

Sub Total For (II) 220/132/33kVInaruwa Substation

IIIKATHMANDU LDC/132 KV DUHABISUBSTATIONPart-A: EMPLOYER ASSESSEDQUANTITIES $$



a


1 No.

35 of 57

a


1 No.




2 No.

BTermination Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

a


2 No.

35 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)





ii2 wire (sub/exchange) voice channelcards (min 8 channels per card) 1 No.




CEquipment Cabinets (Ref. Volume-II,Section-VI, Chapter 16 & 17)




E Synchronization Equipment (Ref.Volume-II, Section-VI, Chapter 16 & 17)GPS clock including all hardware &accessories 1 Set

36 of 57

GPS clock including all hardware &accessories 1 Set

F

Main Distribution Frame (100 pairs)(Ref. Volume-II, Section-VI, Chapter 16& 17)

1 No.




1 No.

Sub-Total Part-APart-B : CONTRACTOR ASSESSEDQUANTITIES $$$Sub-Total Part-B



36 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)





1 Set$




c Tributary Cards



1 No.


a

Drop/Insert Multiplexer Commoncards, Power supply cards, powercabling, other hardware & accessories(each)

1 Set$


37 of 57






37 of 57






(1)(2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)



C

Pre Connectorized Optical Fiber PatchCords (10 Mtrs) – Pack of Six PatchCords (Ref. Volume-II, Section-VI,Chapter 16 & 17)

1 Set

Sub-Total Part-C

SubTotal (III) For KATHMANDULDC/132KV DUHABI SUBSTATION


NOTE

#

##

***

** Set shall include all required hardware/software for complete TMN –Craft Terminal system as specified in technicalspecificationsOne set of installation hardware shall contain all installation hardware fittings as may be required for 1 km ofApproach Fibre Optic cable.

Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as many columns for ForeignCurrency requirement as there are foreign currencies.

Optical interface/SFP can be provided with Optical base card or Control card with the condition that control card shallnot be equipped with more than one Optical interface/SFP and optical card with not more than two Opticalinterface/SFP. However main and protection channel shall be terminated on separate cardsSuitable Optical Interface Card(s) or any other solution such as SDH equipment with optical amplifier, wavelengthtranslator or higher aggregate bit rate SDH equipment may be offer for the lengths to meet the link budgetrequirements without repeater.

38 of 57

**

****

###

$

$$

$$$

Date:Place:

Common Seal:

Employer assessed quantities are those which are clearly quantifiable as per the scope of the work and are givenunder this heading above.

Set shall include all required hardware/software for complete TMN –Craft Terminal system as specified in technicalspecificationsOne set of installation hardware shall contain all installation hardware fittings as may be required for 1 km ofApproach Fibre Optic cable.


Those equipments under heading KATHMANDU LDC/132 KV DUHABI SUBSTATION shall be used in any of the stationsand same shall be finalized during the detail engineering.Employer shall hand over the equipments that had been already supplied (Hetauda Substation equipments shall handover at Hetauda Substation Site and Inaruwa Substation equipments shall hand over at NEA Dhalkebar Substation Site)as per annexure –VIII of Technical Specification Chapter-1. Contractor shall take care of Installation All Risks Insuranceof the same equipments as per Section-IX, Appendix 3. Insurance Requirements of Bidding Documents and it shall beincluded in the present scope of work

Contractor assessed quantities are those which bidders are required to estimate for the entire execution of the workand shall incorporate in their price schedules


38 of 57


ForeignCurrency Portion


Foreign CurrencyPortion


(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

I 220/132kV Hetauda SubstationPart-A: EMPLOYER ASSESSED QUANTITIES $$

A LT TRANSFORMER (Ref. Volume-II, Section-VI,Chapter 7)

1.0 630 kVA,11/0.400 kV 1 No

B 245 kV equipment (Ref. Volume-II, Section-VI,Chapter 3)

1 245 kV Circuit Breakers (3-Phase) with supportstructure

a 1600A, 40KA 7 Nosb 2500A, 40KA 1 No

2 245kV Isolator (3-phase)-Double Breaka 1600A, 40 KA, Isolator with one E/S 7 Nosb 1600A, 40 KA, Isolator with two E/s 7 Nosc 1600 A, 40KA, Tandem Isolator without E/S 13 Nosd 2500A, 40 KA, Isolator with two E/s 2 Nos

3 245 kV Current Transformer (1-Phase)a 1600A, 40KA with 120% extended current rating 21 Nos


Total Price#


Part - B: Installation Charges

Bidder's Name & Address:Schedule No. 4. Installation Services


Unit Price#

39 of 57

a 1600A, 40KA with 120% extended current rating 21 Nosb 1600 A, 40KA with 150% extended current 3 Nos

4 245 kV Capacitive Voltage Transformer (1- Phase)

a 4400 pF 18 Nos.

5.0 216 kV Surge Arrestors (1-phase) 18 Nos.


C145 kV equipment (Ref. Volume-II, Section-VI,Chapter 3)

1.0 145 kV Circuit Breaker (3-Phase) with supportstructure

a 1250A, 31.5 kA 3 Nos

2.0 145kV Isolator (3-phase)-HDBa 1250A, 31.5 KA, Isolator with one E/S 3 Nosb 1250 A, 31.5KA, Isolator without E/S 6 Nos

3.0 145 kV Current Transformer (1- Phase)a 800A, 31.5 kA with 120% extended rating 9 Nos

4.0 145 kV Surge Arrestorsa 120 kV Surge Arrestors (1- Phase) 15 Nos


D11 kV equipment (Ref. Volume-II, Section-VI,Chapter 3)

1.0 9 kV Surge Arrestors (1-Phase) 18 Nos

2.0 11 kV Isolator (3-phase)-HDBa 630A, 25 KA, Isolator with one E/S 4 No

3.0 11kV, 25kA for 1 sec, Indoor Switchgear Panel (3-phase) as per Technical Specification

a 11kV Line module/LT Transformer (800A) (IP-1) 5 Nos

39 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#

Part - B: Installation ChargesSchedule No. 4. Installation Services


Unit Price#

b 11kV Transformer incomer module (800A) (IP-2) 1 Nos


E RELAY PANELS (WITH AUTOMATION) (Ref.Volume-II, Section-VI, Chapter 14)

1.0 220 kVa Circuit Breaker Relay Paneli With Auto Reclose 4 Nosii With out Auto Reclose 4 Nosb Line Protection Panel 4 Nosc Transformer Protection Panel (For both HV & MV

side) 2 Nosd Bus Bar Protection Panel 1 Nos

2 132 kVa Circuit Breaker Relay Paneli With out Auto Reclose 3 Nosb Transformer Protection Panel (For HV) 1 Nosc Augmentation of existing bus bar protection

scheme.(No. of bays as specified) 3 Nos

3.0 11 kVa Protection Panel for 132 and 11 kV Side of

Transformer (as per TS) 1 Nosb Protection Panel for Line (as per TS) 4 Nos

FCONTROL AND RELAY PANELS (WITHOUTAUTOMATION/CONVENTIONAL) (Ref. Volume-II,Section-VI, Chapter 14)

40 of 57

FCONTROL AND RELAY PANELS (WITHOUTAUTOMATION/CONVENTIONAL) (Ref. Volume-II,Section-VI, Chapter 14)


G COMMON EQUIPMENTS (Ref. Volume-II, Section-VI, Chapter 2 & 14)


H SUBSTATION AUTOMATION (Ref. Volume-II,Section-VI, Chapter 16)

H.1

Complete Substation automation system/Augumentation Substation automation system-including hardware and software for thesubstation & remote control stations alongwithassociated equipments as per TechnicalSpecification.

a Main bays to be automatedi 220 kV system 8 Bay Nosii 132 kV System 3 Bay Nosiii 11kV HT indoor switchgear 1 Set

I DPC & PABX (Ref. Volume-II, Section-VI, Chapter15)

a Digital Protection Coupler 2 Nosb PBAX with following configuration as per TS 1 Seti) 2 wire subscriber interface card with capacity 32

local subscribers (along with 32 nos. Instruments)

ii) 4 wire E & M interface card with capacity 8 nos.trunks

iii) E-1 interface with 2 trunks G-703iv) 2 wire interface with 1 trunk (For PSTN)c Testing & Maintenance equipment (print test kit

only) 1 Set

J LT Switchgear (Ref. Volume-II, Section-VI,Chapter 4)

a 400V Main switchboard 1 Setb 400V ACDB 1 Set

40 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

c 400V MLDB 1 Setd 400V Emergency LDB 1 Sete 220V DCDB 2 Set

f400A MCCB I No. along with mounting wiring,accessories etc. 1 Set


K Batteries (Ref. Volume-II, Chapter 5)a 220Vi 600 AH 2 Nos

L Float Cum Boost Battery Charger (Ref. Volume-II, Section-VI, Chapter 5)

a 220V Float Cum Boost Battery Charger

i 80A/80A 2 NosM Fire Protection System (Ref. Volume-II, Chapter

8)a Portable /Trolley/Wheel mounted extinguishersi 9 litre water type 2 Nosii 50 litre foam type 2 Nosiii 4.5 kg CO2 type 6 Nosiv 4.5 kg Dry Chemical Power (DCP) type 2 Nosb Smoke detection system 1 Setc Fire detection and Alarm System 1 Set

NCables along with clamps, glands, lugs andstraight joints etc. (Ref. Volume-II, Section-VI,Chapter 9)

41 of 57

NCables along with clamps, glands, lugs andstraight joints etc. (Ref. Volume-II, Section-VI,Chapter 9)

a 11 kV HT Cable alongwith accessories 0.5 KMb Power Cables - (1.1kV grade)i 3.5Cx300 sqmm (XLPE) cable for interconnection

of New LT Switchgear Main Switchboard &Existing ACDB 1 KM

ii 3.5Cx300 sqmm (XLPE) cable for filter Machinealong with termination arrangement as per TS 1 KM

c 11kV HT cablei 1CX630Sqmm 1500 Mtrsii 1CX300sqmm 3000 Mtrsiii 11kV HT cable termination alongwith accessories

& jointing kit 12 set

N.1132kV XLPE Power cable for connectivity of 132kVD/C Line (Bharatpur/Old Hetauda) at HetaudaSubstation

i 132kV, XLPE insulated, 1CX800sqmm size coppercable as per technical specification.

1035 Route Mtrs

ii Cable termination as per technical specificationand interconnection with overhead transmissionfor cable at sl.no. i above (excluding terminatingstructure)

14 Nos.

OAir conditioning System for Control room cumadministrative building (Ref. Volume-II, Section-VI, Chapter 10)


PSTEEL STRUCTURES (Tower,Gantry structures&Equipment support structures) (Ref. Volume-II,Section-VI, Chapter 12)

P.1 PIPE/LATTICE STRUCTURESa M.S Structural steel including Foundation Bolts

complete. 485 MTb Fastners.(Nuts,Bolts & Washers) 20 MT

QTransmission Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

41 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

Q.1SDH Equipment ( STM - 1 upgradable to STM-4ADM, upto two directions)

a

Base Equipment (Common cards, Cross-connect/control cards, Optical base card, Powersupply cards, power cabling, other hardware &accessories including sub-racks, patch cords, DDFetc. fully equipped excluding (b) and (c) below) 1 No.

b Optical Interface/SFP## fori L1.2 2 No.ii Optical Line Interface card (to support minimum

150 kms)*** 2 No.c Tributary Cardsi E1 Interface card (Minimum 16 interfaces per

card ) 2 No.d Ethernet interfaces 10/100 Mbps with Layer-2

switching (Minimum 4 interfaces per card.) 2 No.

RTermination Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

a Drop/Insert Multiplexer Base Equipment(Common cards, Power supply cards, powercabling, other hardware & accessories includingsub-racks, etc. fully equipped excludingsubscriber line interface cards)

2 No.

b Subscriber Line Interface Cardsi 2 wire (sub/sub) voice channel cards (min 8

channels per card) 2 No.ii 4 wire (E&M) voice channel cards (min 8 channels

per card) 2 No.

42 of 57

ii 4 wire (E&M) voice channel cards (min 8 channelsper card) 2 No.

iii Asynchronous Sub Channels data cards (minimum4 channels per card) 2 No.


SEquipment Cabinets (Ref. Volume-II, Section-VI,Chapter 16 & 17)

a For Drop/Insert Multiplexer 1 No.b For SDH Equipment 1 No.T Main Distribution Frame (100 pairs) (Ref.

Volume-II, Section-VI, Chapter 16 & 17) 1 No.

UFODP (Ref. Volume-II, Section-VI, Chapter 16 &17)

a FODP (minimum 48 Fibres) : Indoor Type, rackmounted with FCPC coupling and pig tails 1 No.

VFibre Optic approach cable (Ref. Volume-II,Section-VI, Chapter 17)

a 48 Fibre (DWSM -G.652D) 0.5 Km.b Installation hardware set for above 48 Fibre,

Fibre Optic Approach Cable 0.5 Set ****

Sub-Total Part-A

Part-B : CONTRACTOR ASSESSED QUANTITIES$$$

A Erection Hardware (Ref. Volume-II, Section-VI,Chapter 11)Insulator strings, Disc Insulators, Hardware,conductor, Al tube, bus-bar materials, cable trays,Bay MB, clamps, spacers, connectors includingequipment connectors, Junction box, earthwire,buried cable trenches/pipe equipment & lighting,all accessories etc. for the following:

a 220 kV Layout (DMT Layout)i Line Bay 4 Setii Transformer Bay 2 Setiii TBC Bay 1 Setiv BC bay 1 Setv Bus work (Three Bays) 4 Setb 132 kV (Double Main Layout)

42 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

i Transformer Bay 3 Setii Bus work (For one bays) 5 Set

c.1 11kV HT indoor switchgear 1 Set

c Earthing and lightning protection includingnecesaary connectors/connections, risers etc.complete in all respect


d

Interconnection arrangement of 132kV cabletermination yard between dead end towerof132kV Bharatpur/Hetauda(old) D/C lines alongwith provision of spare 132kv cable connectivityas per technical specification

1 Set

B Fire Protection System (Ref. Volume-II, Section-VI, Chapter 8)

a Pumping arrangement for HVW system &hydrant system, complete with all piping, valves,fittings,etc. inside pump house

i 220/132/11kV (New) Substation 1 Set


i 220/132/11kV (New) Substation 1 Set

c

HVW spray system, Hydrant system and completeU/G & O/G piping and accessories etc. out sidethe pump house for Transformer / Reactor :

43 of 57

c

HVW spray system, Hydrant system and completeU/G & O/G piping and accessories etc. out sidethe pump house for Transformer / Reactor :

c.1 Transformeri 100MVA , 220/132 KV, 3-phase Autotransformer 2 Setsii 10MVA , 132/11 KV, 3-phase Transformer 1 Sets

C Illumination System (Ref. Volume-II, Section-VI,Chapter 6)

a Auxiliary Building 1 LSb Switchyard lighting 1 LSc Street lighting 1 LS

D SUBSTATION AUTOMATION (Ref. Volume-II,Section-VI, Chapter 16)

a

Integration of all 220/132/33kV Bays underpresent scope with the SCADA of SIEMENS(SINAUT Spectrum) at Load Dispatch Centre,Kathmandu including supply of Hardware,Software, accessories etc. as per TS SectionProject.

1 LS

EPOWER & CONTROL CABLES (Ref. Volume-II,Section-VI,Chapter 9)

a Power Cables(PVC)- (1.1kV grade) 1 LSb Power Cables (XLPE)- (1.1kV grade) 1 LSc Control Cable (PVC)- (1.1kV grade) 1 LSd Cable glands, lugs & straight through joints for

Power & Control cables 1 LS

F 132kV XLPE Cable

i

Miscellenous installation materials for cablejointing, bonding , link boxes, earthing material,Earth Continuity Cable, cable markers and allother materials etc required as per technicalspecification and as per statutary requirements

1 LS

Sub-Total Part-B

SubTotal (I) For 220/132kV Hetauda Substation

43 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

II 220/132/33kV Inaruwa SubstationPart-A: EMPLOYER ASSESSED QUANTITIES $$

A LT TRANSFORMER (Ref. Volume-II, Section-VI,Chapter 7)

1.0 630 kVA,33/0.400 kV 2 No

B 245 kV equipment (Ref. Volume-II, Section-VI,Chapter 3)

1 245 kV Circuit Breakers (3-Phase) with supportstructure

a 1600A, 40KA 9 Nosb 2500A, 40KA 1 No

2 245kV Isolator (3-phase)-Double Breaka 1600A, 40 KA, Isolator with one E/S 9 Nosb 1600A, 40 KA, Isolator with two E/s 9 Nosc 1600 A, 40KA, Tandem Isolator without E/S 17 Nosd 2500A, 40 KA, Isolator with two E/s 2 Nos

3 245 kV Current Transformer (1-Phase)a 1600A, 40KA with 120% extended current rating 27 Nosb 1600 A, 40KA with 150% extended current 3 Nos

4 245 kV Capacitive Voltage Transformer (1- Phase)

a 4400 pF 18 Nos.

44 of 57

5.0 216 kV Surge Arrestors (1-phase) 24 Nos.


C 145 kV equipment (Ref. Volume-II, Section-VI,Chapter 3)

1.0 145 kV Circuit Breaker (3-Phase) with supportstructurea 1250A, 31.5 kA 9 Nos

2.0 145kV Isolator (3-phase)-HDBa 1250A, 31.5 KA, Isolator with one E/S 12 Nosb 1250 A, 31.5KA, Isolator without E/S 22 Nos

3.0 145 kV Current Transformer (1- Phase)a 800A, 31.5 kA with 120% extended rating 27 Nos

4.0 145 kV Surge Arrestorsa 120 kV Surge Arrestors (1- Phase) 24 Nos


6.0 145 kV Capacitive Voltage Transformer (1- Phase)

a 4400 pf 18 Nos

D36 kV equipment (Ref. Volume-II, Section-VI,Chapter 3)

1.0 36 kV Circuit Breaker (3-Phase) with supportstructure

a 1250A, 25 kA, 3 Sec 9 Nos

2.0 36 kV Current Transformer (1- Phase)a 600A, 25 kA with 120% extended rating 18 Nosb 1250A, 25 kA with 120% extended rating 6 Nosc 2000A, 25 kA with 120% extended rating 3 Nos

3.0 36 kV Isolator (3-phase)-HDBa 1250A, 25 KA, Isolator with one E/s 8 Nos

44 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

b 1250A, 25 KA, Isolator without E/S 12 Nos

4.0 30 kV Surge Arrestors (1-Phase) 30 Nos


6.0 36kV Voltage Transformer (1- Phase) 6 Nos

7.0 Bus post insulators 12 Nos

E RELAY PANELS (WITH AUTOMATION) (Ref.Volume-II, Section-VI, Chapter 14)

1.0 220 kVa Circuit Breaker Relay Paneli With Auto Reclose 2 Nosii With out Auto Reclose 6 Nosb Line Protection Panel 2 Nosc Transformer Protection Panel (For both HV & MV

side) 4 Nosd Bus Bar Protection Panel 1 Nos

2 132 kVa Circuit Breaker Relay Paneli With Auto Reclose 4 Nos.ii With out Auto Reclose 5 Nos.b Line Protection Panel 4 Nos.c Reactor Protection Panel 1 Nos.d Shunt Capacitor Protection Panel 1 Nos.

45 of 57

d Shunt Capacitor Protection Panel 1 Nos.e Bus Bar Protection Panel 1 Nos.

3.0 33 kVa Protection Panel for 33kV Side Transformer (as

per TS) 2 Nosb Protection Panel for Line (as per TS) 6 Nosc Protection Panel for Bus Sectionalizer 1 Nos

FCOMMON EQUIPMENTS (Ref. Volume-II,Section-VI, Chapter 14)

1 Special Relay Test kit 1 No

GSUBSTATION AUTOMATION (Ref. Volume-II,Section-VI, Chapter 16)

G.1

Complete Substation automation system/Augumentation Substation automation system-including hardware and software for thesubstation & remote control stations alongwithassociated equipments as per TechnicalSpecification.


H DPC & PABX (Ref. Volume-II, Section-VI, Chapter15)

a Digital Protection Coupler 10 Nosb PBAX with following configuration as per TS 1 Seti) 2 wire subscriber interface card with capacity 32

local subscribers (along with 32 nos. Instruments)

ii) 4 wire E & M interface card with capacity 8 nos.trunks

iii) E-1 interface with 2 trunks G-703iv) 2 wire interface with 1 trunk (For PSTN)c Testing & Maintenance equipment (print test kit

only) 1 Setd 4 wire telephone equipment 1 Nos

45 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

e Installation of Two nos. DPC each at RupaniSubstation and Duhabi Substation for completeteleprotection applications to complete the scopeof works.

1 LS

I LT Switchgear (Ref. Volume-II, Section-VI,Chapter 4)

a 400V Main switchboard 1 Setb 400V ACDB 1 Setc 400V MLDB 1 Setd 400V Emergency LDB 1 Sete 220V DCDB 2 Setf 48/50V DCDB 2 Set

J Batteries(Ref. Volume-II, Section-VI, Chapter 5)a 220Vi 600 AH 2 Nosb 48Vi 600 AH 2 Nos

K Float Cum Boost Battery Charger (Ref. Volume-II, Section-VI, Chapter 5)

a 220V Float Cum Boost Battery Charger

i 80A/80A 2 Nosb 48V Float Cum Boost Battery Chargerii 60A/60A 2 Nos

46 of 57

L Fire Protection System (Ref. Volume-II, Section-VI, Chapter 8)

a Portable /Trolley/Wheel mounted extinguishersi 9 litre water type 5 Nosii 50 litre foam type 2 Nosiii 4.5 kg CO2 type 13 Nosiv 4.5 kg Dry Chemical Power (DCP) type 5 Nosb Smoke detection system 1 Setc Fire detection and Alarm System 1 Set

M Cables along with clamps, glands, lugs andstraight joints etc. (Ref. Volume-II, Section-VI,Chapter 9)


i3.5Cx300 sqmm (XLPE) cable for filter Machinealong with termination arrangement as per TS 1 KM

N

Air conditioning System for Control room cumadministrative building (Ref. Volume-II, Section-VI, Chapter 10)


O STEEL STRUCTURES (Tower,Gantry structures&Equipment support structures) (Ref. Volume-II,Section-VI, Chapter 12)

O.1 PIPE/LATTICE STRUCTURESa M.S Structural steel including Foundation Bolts

complete. 523 MTb Fastners.(Nuts,Bolts & Washers) 15 MT

PTransmission Equipment (Ref. Volume-II, Section-VI, Chapter 16 & 17)

P.1SDH Equipment ( STM - 1 upgradable to STM-4ADM, upto two directions)

46 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

a

Base Equipment (Common cards, Cross-connect/control cards, Optical base card, Powersupply cards, power cabling, other hardware &accessories including sub-racks, patch cords, DDFetc. fully equipped excluding (b) and (c) below)

1 No.


iOptical Line Interface card (to support minimum175 kms)*** 2 No.

c Tributary Cards

iE1 Interface card (Minimum 16 interfaces percard ) 2 No.

ii Ethernet interfaces 10/100 Mbps with Layer-2switching (Minimum 4 interfaces per card.) 2 No.

QTermination Equipment(Ref. Volume-II, Section-VI, Chapter 16 & 17)

a

Drop/Insert Multiplexer Base Equipment(Common cards, Power supply cards, powercabling, other hardware & accessories includingsub-racks, etc. fully equipped excludingsubscriber line interface cards) 2 No.


i2 wire (sub/sub) voice channel cards (min 8channels per card) 2 No.

ii4 wire (E&M) voice channel cards (min 8 channelsper card) 2 No.

iiiAsynchronous Sub Channels data cards (minimum4 channels per card) 2 No.

47 of 57

iiiAsynchronous Sub Channels data cards (minimum4 channels per card) 2 No.


REquipment Cabinets (Ref. Volume-II, Section-VI,Chapter 16 & 17)


SMain Distribution Frame (100 pairs)(Ref. Volume-II, Section-VI, Chapter 16 & 17) 1 No.

T FODP (Ref. Volume-II, Section-VI, Chapter 16 &17)

a FODP (minimum 48 Fibres) : Indoor Type, rackmounted with FCPC coupling and pig tails 1 No.

UFibre Optic approach cable (Ref. Volume-II,Section-VI, Chapter 17)

a 48 Fibre (DWSM -G.652D) 0.5 Km.b Installation hardware set for above 48 Fibre,

Fibre Optic Approach Cable 0.5 Set ****

Sub-Total Part-A

Part-B : CONTRACTOR ASSESSED QUANTITIES

AErection Hardware (Ref. Volume-II, Section-VI,Chapter 11)Insulator strings, Disc Insulators, Hardware,conductor, Al tube, bus-bar materials, cable trays,Bay MB, clamps, spacers, connectors includingequipment connectors, Junction box, earthwire,buried cable trenches/pipe equipment & lighting,all accessories etc. for the following:

a 220 kV Layout (DMT Layout)i Line Bay 4 Setii Transformer Bay 4 Setiii TBC Bay 1 Setiv BC bay 1 Setv Bus work (Three Bays) 4 Setb 132 kV (Double Main Layout)i Line Bay 4 Setii Transformer Bay 2 Set

47 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

iii BC Bay 1 Setiv Bus work (For one bays) 9 Setv Bus Reactor Bay 1 Setvi Shunt Capacitor Bay 1 Setc 33 kV (Single Main Bus Layout) LSi Line Bay 6 Setii Transformer Bay 2 Setiii Bus work (For Four bays) 2 Setiv Sectionalizer 1 Set

dEarthing and lightning protection includingnecesaary connectors/connections, risers etc.complete in all respect


B Fire Protection System (Ref. Volume-II, Section-VI, Chapter 8)

aPumping arrangement for HVW system &hydrant system, complete with all piping, valves,fittings,etc. inside pump house



i 220/132kV (New) Substation 1 Setc HVW spray system, Hydrant system and complete

U/G & O/G piping and accessories etc. out sidethe pump house for Transformer / Reactor :

48 of 57

c HVW spray system, Hydrant system and completeU/G & O/G piping and accessories etc. out sidethe pump house for Transformer / Reactor :

c.1 Transformer

i100MVA , 220/132 KV, 3-phase Autotransformer

2 Setsii 63MVA , 220/33 KV, 3-phase Autotransformer 2 Sets


CIllumination System (Ref. Volume-II, Section-VI,Chapter 6)

a Illumination System for switchyard panel roomi 220KV 3 Setsii 132kV 2 Setsiii 33kV 1 Set

bControl room cum administrative buildingillumination 1 LS


DAir conditioning System (Ref. Volume-II, Section-VI, Chapter 10)

a Air conditioning for S/Y panel roomi 220KV 3 Setsii 132kV 2 Setsiii 33kV 1 Set

ESUBSTATION AUTOMATION (Ref. Volume-II,Section-VI, Chapter 16)

a

Integration of all 220/132/33kV Bays underpresent scope with the SCADA of SIEMENS(SINAUT Spectrum) at Load Dispatch Centre,Kathmandu including supply of Hardware,Software, accessories etc. as per TS SectionProject.

1 LS

FPOWER & CONTROL CABLES (Ref. Volume-II,Section-VI, Chapter 9)

a Power Cables(PVC)- (1.1kV grade) 1 LSb Power Cables (XLPE)- (1.1kV grade) 1 LS

48 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

c Control Cable (PVC)- (1.1kV grade) 1 LSd Cable glands, lugs & straight through joints for

Power & Control cables 1 LS

Sub-Total Part-B

Sub Total (II) For 220/132/33kV InaruwaSubstation

III KATHMANDU LDC/ 132kV DUHABI SUBSTATIONPart-A : EMPLOYER ASSESSED QUANTITIES

A Transmission Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)

A.1SDH Equipment ( STM - 1 upgradable to STM-4ADM, upto two directions)

a

Base Equipment (Common cards, Cross-connect/control cards, Optical base card, Powersupply cards, power cabling, other hardware &accessories including sub-racks, patch cords, DDFetc. fully equipped excluding (b) and (c) below) 1 No.



49 of 57


ii Ethernet interfaces 10/100 Mbps with Layer-2switching (Minimum 4 interfaces per card.) 2 No.


a

Drop/Insert MultiplexerBase Equipment (Common cards, Power supplycards, power cabling, other hardware &accessories including sub-racks, etc. fullyequipped excluding subscriber line interfacecards) 2 No.


i2 wire (sub/sub) voice channel cards (min 8channels per card) 2 No.

ii2 wire (sub/exchange) voice channel cards (min 8channels per card) 1 No.

iii4 wire (E&M) voice channel cards (min 8 channelsper card) 2 No.

iv Asynchronous Sub Channels data cards (minimum4 channels per card) 2 No.


CEquipment Cabinets (Ref. Volume-II, Section-VI,Chapter 16 & 17)


DTMN - Craft Terminal for SDH & PDH Equipments(Ref. Volume-II, Section-VI, Chapter 16 & 17)


E Synchronization Equipment (Ref. Volume-II,Section-VI, Chapter 16 & 17)GPS clock including all hardware & accessories 1 Set

FMain Distribution Frame (100 pairs) (Ref.Volume-II, Section-VI, Chapter 16 & 17) 1 No.

Sub-Total Part-A

Part-B: CONTRACTOR ASSESSED QUANTITIES

Sub-Total Part-B

49 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Total Price#



Unit Price#

SubTotal (III) For KATHMANDU LDC/132KVDUHABI SUBSTATION


NOTE

#

##

***

**

****

###

$

$$

$$$

Optical interface/SFP can be provided with Optical base card or Control card with the condition that control card shall not be equippedwith more than one Optical interface/SFP and optical card with not more than two Optical interface/SFP. However main and protectionchannel shall be terminated on separate cards

Suitable Optical Interface Card(s) or any other solution such as SDH equipment with optical amplifier, wavelength translator or higheraggregate bit rate SDH equipment may be offer for the lengths to meet the link budget requirements without repeater.

Set shall include all required hardware/software for complete TMN –Craft Terminal system as specified in technical specifications

One set of installation hardware shall contain all installation hardware fittings as may be required for 1 km of Approach Fibre Optic cable.

Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as many columns for Foreign Currencyrequirement as there are foreign currencies.

The testing capacity of SDH analyser shall be provided according to offered SDH equipmentOne Set means one of each type of module/unit card etcEmployer assessed quantities are those which are clearly quantifiable as per the scope of the work and are given under this headingabove.Contractor assessed quantities are those which bidders are required to estimate for the entire execution of the work and shallincorporate in their price schedules

Those equipments under heading KATHMANDU LDC/132 KV DUHABI SUBSTATION shall be used in any of the stations and same shall befinalized during the detail engineering.

Employer shall hand over the equipments that had been already supplied (Hetauda Substation equipments shall hand over at HetaudaSubstation Site and Inaruwa Substation equipments shall hand over at NEA Dhalkebar Substation Site) as per annexure –VIII of TechnicalSpecification Chapter-1. Contractor shall take care of Installation All Risks Insurance of the same equipments as per Section-IX, Appendix3. Insurance Requirements of Bidding Documents and it shall be included in the present scope of work.

50 of 57

Date:Place:

Common Seal:


Designation:

Employer shall hand over the equipments that had been already supplied (Hetauda Substation equipments shall hand over at HetaudaSubstation Site and Inaruwa Substation equipments shall hand over at NEA Dhalkebar Substation Site) as per annexure –VIII of TechnicalSpecification Chapter-1. Contractor shall take care of Installation All Risks Insurance of the same equipments as per Section-IX, Appendix3. Insurance Requirements of Bidding Documents and it shall be included in the present scope of work.

50 of 57






(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)I 220/132kV Hetauda Substation

PART-C: Civil Works (Refered to Volume II, Section-VI,Chapter-13, Civil Works)

C1 SECTION: 1 : EMPLOYER ASSESSED QUANTITIES $$

1.0Excavation in all types of soil and rock includingbackfilling disposal etc. for all leads and lifts

13436 Cu.Mtr.

2.0Providing and laying of Plain Cement Concrete (PCC)(1:4:8)

512.52 Cu.Mtr.


219 Cu.Mtr.

4.0

Providing and laying of Reinforced Cement ConcreteDesign Mix (M25) including pre cast, shuttering,Grouting of pockets & underpinning but excluding steelreinforcement.

3070.99 Cu.Mtr.

5.0Providing and laying Plain Cement Concrete 1:5:10 (1cement : 5 sand : 10 Stone aggregate)

1758.08 Cu.Mtr.

6.0 Steel Reinforcement (Fe 500) 173.08 MT

7.0

Miscellaneous Structural steel used for rails , plates forrail fixing, ,gratings, gratings supports etc fortransformer /reactor foundation,cable supportstandearthing cleats ,chequered plates, embedments, edgeprotection angles for cable trenches but excluding thereinforcement steel and steel for lattice and pipestructures which shall be paid seperately.

60 MT

8.0Stone filling (40mm) over grating of Transformer/ReactorFoundation

45 Cu.Mtr.

Bidder's Name & Address:Schedule No. 4. Installation ServicesPart - C: Civil Works


Total Price#Sl.No.

Item Description Qty. Unit

Unit Price#

51 of 57

8.0Stone filling (40mm) over grating of Transformer/ReactorFoundation

45 Cu.Mtr.

9.0Stone spreading including antiweed treatment inswitchyard but excluding PCC.

23500 Sq. Mtr.

10.00

Supplying & laying hume pipe with collarsof grade (NP-3)but excluding reinforcement steel & concrete ofbed/support/encasing of hume pipes which shall be paidseperately

i) 250mm dia 20 RMii) 300mm dia 20 RMiii) 450mm dia 10 RMiv) 600mm dia 10 RM

11.00Concrete road (including all crossings) as perSpecification & approved drawing but excludingreinforcement & concrete

a. Concrete Road 790 Sq. m.

12.0

Construction of rail-cum-raod as per approved drawingincluding all items such as excavation, compaction,rolling, watering, WBM, etc but excluding concrete,reinforcement and structural steel which shall be paidseperately

a. Section having two rails 135 Sq. m.

13.0Chain link fencing as per technical specification &approved drawing but excluding concrete which shall bepaid seperately

200 RM

14.0 Switch yard Gate excluding concrete 1 No.

15.0

Dismantling & rerection of existing fence includingsorting and stacking of serviceable & non-serviceablematerials and disposal of debris as per the direction ofengineer-in-charge

50 RM

16.00 Supplying and erecting dewatering pumpsa. 5 HP 1 Nos.b. 0.5 HP 3 Nos.

17.00Drain including culverts but excluding concrete &reinforcement steel which shall be paid sepretely

a. Type AA (300mm wide x Depth up to 600mm) 250 RMb. Type BB (450 wide x Depth From 600 to 900mm) 125 RMc. Type CC (600 wide x Depth From 900 to 1200mm) 75 RMd. Type DD ( 750 wide x Depth From 1200 to 1500mm) 50 RM

18.0Stone soling below foundations wherever specified inapproved drawings during detailed engineering

150 Cu.Mtr.

51 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)

Schedule No. 4. Installation ServicesPart - C: Civil Works

Total Price#Sl.No.


Unit Price#

19132kV XLPE Power cable for connectivity of 132kV D/CLine (Bharatpur/Old Hetauda)

iLaying & Jointing etc for 7 nos,1C, 800 sqmm size cablesalongwith all necessary installation material

150 Route Mtrs

ii

Construction of buried cable trench for 132kV XLPECable including road crossing: All civil works alongwithback filling, restoration etc (as per specification)excavation, PCC, sand filling, brick laying, PVC warningtapes, RCC hume pipes(NPs) for road crossing along withcollars and jointing of suitable dia etc. required tocomplete buried cable trench shall be deemed to beincluded in the item of work.

150 Mtrs

20 Site levelling

a)Earth work in cutting & Filling and in filling withborrowed earth

33537.6 Cu.Mtr.

C2 SECTION: 2 : CONTRACTOR ASSESSED QUANTITIES $$$

1.00

All civil works as per technical specification andapproved drawing and including Misc. structural steel (items like excavation, PCC, RCC, reinforcement, externalfinishing and miscellaneous steel used for cable trenchesinside building if any shall be measured and paid as perrate of SECTION: 1 : EMPLOYER ASSESSED QUANTITIES.

i FFPH building including fire water tank. 1 LSii Auxilliary Building (15 M X 15 M). 1 LSiii Parking shed (for 10 cars) 1 LS

2.00External finish as per specification for followingbuildings:

52 of 57

iii Parking shed (for 10 cars) 1 LS


i FFPH building including fire water tank. 1 LSii Auxilliary Building (15 M X 15 M). 1 LSiii Parking shed (for 10 cars) 1 LS3 Geotechnical/Soil Investigation 1 LS

4

Civil works associated with mounting erection of 11kVHT indoor including indoor cable trench by cuttingchipping existing floor, existing control room misc. steelof switchgear inside building etc. complete as pertechnical specification

1 LS

5Non-destructive i.e. core cutting test in line withrelevant Indian Standard code (IS:456, IS:516 & IS:1199)

20 Nos

6 Dismantling & of existing 220 kV RCC Foundations 10 NosSub-Total Part-C- Hetauda

II 220/132/33kV Inaruwa SubstationPART-C: Civil Works (Refered to Volume II, Section-VI,Chapter-13, Civil Works)

C1 SECTION: 1 : EMPLOYER ASSESSED QUANTITIES $$

1.0Excavation in all types of soil and rock includingbackfilling disposal etc. for all leads and lifts

25690 Cu.Mtr.


2413 Cu.Mtr.


652 Cu.Mtr.

4.0

Providing and laying of Reinforced Cement ConcreteDesign Mix (M25) including pre cast, shuttering,Grouting of pockets & underpinning but excluding steelreinforcement.

6200 Cu.Mtr.

5.0Providing and laying Plain Cement Concrete 1:5:10 (1cement : 5 sand : 10 Stone aggregate)

3750 Cu.Mtr.

6.0 Steel Reinforcement (Fe 500) 340 MT

52 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)


Total Price#Sl.No.


Unit Price#

7.0

Miscellaneous Structural steel used for rails , plates forrail fixing, ,gratings, gratings supports etc fortransformer /reactor foundation,cable supportstandearthing cleats ,chequered plates, embedments, edgeprotection angles for cable trenches but excluding thereinforcement steel and steel for lattice and pipestructures which shall be paid seperately.

110 MT

8.0Stone filling (40mm)over gatings of Transformer/ReactorFoundation

75 Cu.Mtr.

9.0Stone spreading including antiweed treatment inswitchyard but excluding PCC.

50000 Sq. Mtr.

10.00Supplying & laying hume pipe of grade (NP-3) exceptreinforcement & concrete of bed/support/encasing ofhume pipes which shall be paid seperately

i) 250mm dia 50 RMii) 300mm dia 50 RMiii) 450mm dia 30 RMiv) 600mm dia 30 RM

11.0Concrete road (including all crossings) as per approveddrawing & Specification but excluding reinforcement &concrete

a. Concrete road 6750 Sq. m.

12.0Construction of Black Top (Bituminous) road as perSpecification & approved drawing, all Complete

i) Black top/Bituminous(asphaltic)Road. 5625 Sq. m.

13.0

Construction of rail-cum-raod as per technicalspecification and approved drawing including all itemssuch as excavation, compaction, rolling, watering, WBM,etc but excluding concrete, reinforcement and structuralsteel which shall be paid seperately

53 of 57

13.0

Construction of rail-cum-raod as per technicalspecification and approved drawing including all itemssuch as excavation, compaction, rolling, watering, WBM,etc but excluding concrete, reinforcement and structuralsteel which shall be paid seperately

a. Section having two rails 225 Sq. m.

14.0Chain link fencing as per approved drawing but excludingconcretewhich shall be paid seperately

700 RM

15.0 Gate excluding concrete 1 No

16.0Rain water Harvesting as per technical specification &approved drawing but excluding reinforcement &concrete which shall be paid seperately

1 No

17.00 Supplying and erecting dewatering pumpsa. 5 HP 2 Nos.b. 0.5 HP 4 Nos.

18.00Drain including culverts but excluding concrete, humepipes & reinforcement steel which shall be paidseperately

a. Type AA (300mm wide x Depth up to 600mm) 3600 RMb. Type BB ( 450 wide x Depth From 600 to 900mm) 1800 RMc. Type CC (600 wide x Depth From 900 to 1200mm) 1200 RMd. Type DD (750 wide x Depth From 1200 to 1500mm) 600 RM

19.00

External water supply as per technical from borewell toFire water Tank, control room Building including all itemslikeexcavation,pipes,fittings,jointings,valves,chambers/manholes etc

a. 80mm Dia GI Pipe 100 RMb. 25mm Dia GI Pipe 100 RM

20.00External sewerage system including all item such asexcavation, piping, pipe fittings, manholes, gali trap, galichamber etc.

a. (i) 250 mm Dia. 50 RMb. (i) 150 mm Dia. 50 RM

21.0Stone soling below foundations wherever specified inapproved drawings during detailed engineering

350 Cu.Mtr.

53 of 57





(1) (2) (3) (4) (5) (6) (7)=(3)x(5) (8)=(3)x(6)


Total Price#Sl.No.


Unit Price#

22.0

2.5 cm premix carpet surfacing with 2.25cum and 1.12cum of stone chipping of 13.2 mm and 11.2 mm sizerespectively per 100sqm and 52kg and 56kg of hotbitumen per cum of stone chippingof 13.2 mm and 11.2mm size respectively, including a tack coat with hotstraight run [email protected]/sqm, includingconsolidation with road roller of 6 to 9 tonne capacityetc. complete with paving Asphalt of suitable gradeheated and then mixed with solvent at the rate of 70grams per kg of asphalt or with paving Asphalt ofsuitable grade wth no solvent (For strengthening ofexisting roads only )

6000 Sq. m.

23.0

Construction of granular sub-base of WBM by providingclose graded material conforming to specification,mixing in a mechanical mix plant at optimum moisturecontent (OMC ), carriage of mixed material by tippers towork site, for all leads & lifts, spreading in uniform layerof specified thichness with motor grader on preparedsurface and compacting with vibratory poervr roller toacheive the desire density, compete as per specificationand directions of NEA/Consultant WITH MATERIALCONFORMING TO suitable Grade(size range 75mm to0.075 mm) (For strengthening of existing roads only)

600 Cu.Mtr.

24.0 Site levelling 0

a)Earth work in cutting & Filling and in filling withborrowed earth

61956.45 Cu.Mtr.

C2 SECTION 2 : CONTRACTOR ASSESSED QUANTITIES $$$

54 of 57

C2 SECTION 2 : CONTRACTOR ASSESSED QUANTITIES $$$

1.00

All civil works as per technical specification andapproved drawing and including Misc. structural steel (items like excavation, PCC, RCC, reinforcement, externalfinishing and miscellaneous steel used for cable trenchesinside building if any shall be measured and paid as perrate of SECTION: 1 : EMPLOYER ASSESSED QUANTITIES.

i 400 KV Control room building (Double story). 1 LSii FFPH building including fire water tank. 1 LSiii Switch Panel Room (9.0 M X 3.9 M). 5 Setsiv Switch Panel Room (6.0 M X 3.9 M). 1 Setv Parking shed (for 10 cars) 1 LS


i Control room building (Double story). 1 LSii FFPH building including fire water tank. 1 LSiii Switch Panel Room (9.0 M X 3.9 M). 5 Setsiv Switch Panel Room (6.0 M X 3.9 M). 1 Setv Parking shed (for 10 cars) 1 LS

Sub-Total Part-C- InaruwaGrand Total Part-C

#

$$$$$

Common Seal:

Date:Place:

Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as many columns for Foreign Currencyrequirement as there are foreign currencies.

Employer assessed quantities are those which are clearly quantifiable as per the scope of the work and are given under this heading above.Contractor assessed quantities are those which bidders are required to estimate for the entire execution of the work and shall incorporate intheir price schedules

54 of 57

ICB No: NIETTP/W/ICB-3/SSBidder's Name and Address:

Schedule No. 4. Installation ServicesPart-D: Training Charges for Training to be imparted within the Employer's country

1. Price Component of training to be imparted to Owner's Personnel by Bidder's instructor

Sl.No. Description of the Test Item for which training is to be

imparted.

Trainingduration indays

CurrencyNRs.

Per Day TrainingCharges forContractors Trainers

TotalTraining Charges

(1) (2) (3) (4) (5) (6) (7)=(4)x(6)i) Control & Protection 5

ii) Substation Automation Systemincluding integration aspect of existingSCADA (of Siemens suppliedSINAUTSpectrum Software) at Load DispatchCenter

5

iii) Switchyard Equipments (CT, CVT,Isolatot and Circuit Breaker)

5

iv) Telecommunication Equipment(SDH ,MUX & NMS (Craft Terminal))and PLCC

5

Total for Training Charges

Date: Signature:

REMARKS:On Job Training in Nepal: The traveling and living expenses of Owner’s personnel for the training programme conducted in Nepal shall be borne by the Owner.



a)

On Job training onoperation, maintenance andtesting & commissioningaspect at one Location inNepal as per TechnicalSpecification

55 of 57

Place: Printed Name:

Designation:

Common Seal:

55 of 57


Price Schedule No. 5. Grand Summary ( Schedule Nos. 1 to 4)

Foreign Currency Portion Local Currency Portion(1) (2) (3) (4)

1. Total Schedule No. 1. Plant, and MandatorySpares Parts to be supplied from abroad

2.Total Schedule No. 2. Plant, and MandatorySpares Parts to be supplied from within theEmployer's country

3 Total Schedule No. 3. Design Services

4.

Part A: Local Transportation, Insurance and otherIncidental services (including port clearance etc.)

Part - B: Installation Charges

Part- C: Civil Works




Sl. No. Description Total Price#

Price to be included in the "Supply, InstallationCharges and Civil works" Schedules

Schedule No. 4. Installation Services

56 of 57

Part- C: Civil Works

Part - D: Training Charges for Training to be impartedwithin the Employer's country

Total Schedule No. 4. Installation Services

Date:Place:

Common Seal:

Note:# Specify currency in accordance with specifications in Bid Data Sheet under ITB 18.1. Create and use as

many columns for Foreign Currency requirement as there are foreign currencies.

GRAND TOTAL excluding VAT (to Bid Form)


Designation:

56 of 57


CIF or CIP(Foreign Parts)

EXW(Local Parts)

(1) (2) (3) (4) (5) (6)

Item Description Qty.Unit Price#

Total Price#

Procurement of Plant Design, Supply and Installation of 220/132kV Hetauda& InaruwaSubstations



Schedule No.6. Recommended Spare Parts

57 of 57

Date:Place:

Common Seal:

Note:#

TOTAL


Designation:

57 of 57