www.fanatec.com

Quick GuideEN

Fanatec® is a registered trademark of Endor AGDesigned and developed by Endor AG in Germany

Manufactured by

Seligenthaler Straße 16 a - 84034 Landshut - GermanyTelephone: +49 (871) 9221-122 Fax: +49 (871) 9221-221Email: info.webshop@fanatec.comWebsite: www.fanatec.com - www.endor.ag

06/2019

NECESSARY FUNCTIONS ANALOGUE PADDLE MODES

WHEEL COMPATIBILITY

PACKAGE CONTENTS

DATAPORT-C

● To accept the High Torque warning message on a Podium Wheel Base you need to turn the steering wheel 90° and wait until the bar on the wheel base display disappears.

To switch the Mode of your Podium Advanced Paddle Module you need to enter the Tuning Menu. This can be accessed us-ing the FanaLab software or a button/display module.For further information about the APM Modes, please read the Quick Guide from the Podium Advanced Paddle Module.

You need to use M5 screws with a max. length of 16 mm in order to avoid a collision with the Podium Hub. The FANATEC® wheel rims come with the correct screws. If your wheel rim is not pre-drilled, you can use the drilling template on the Podi-um Hub product page.

The DataPort-C on the bottom of the Podium Hub is to connect future Fanatec peripherals with your wheel base.

ATTENTION: It is NOT a USB data port and can’t transfer any data between the PC and any attached device that is not coming from Fanatec®.

● Podium Hub (A)● Quick Release Adapter (B)● 2 mm Allen key (C)●Quick Guide - English

● Centre Calibration can be done by clicking on ‘Centre Cali-bration’ in the driver.

● Shifter Calibration can be done by clicking on ‘Shifter Cali-bration’ in the driver.

● Switching the Mode on the wheel bases without a dedicated “Mode” button is only possible through the Fanatec driver.

● To adjust the Tuning Menu of your wheel base you need to use the FanaLab software or use a suitable button/display module (sold separately).

A B

Ø 70 mm

Ø 50 mm

C

ATTACHING THE PODIUM HUB DETACHING THE PODIUM HUB MOUNTING SHIFTER PADDLES MOUNTING THE BUTTON CLUSTER PACK

MakesurethefirmwareforbothyourFanatecwheelbaseand Podium Hub is up to date. You can obtain the driver package from the Downloads section of the Fanatec website (www.fanatec.com).

● Remove the storage pin

● Compress and hold the Quick Release mechanism

● Loosen the three highlighted screws on the plastic cover

● Loosen the three highlighted screws on the plastic cover

● Remove the front cover● Remove the front cover

● Connect the Button Cluster cables to the correct sockets.

● Attach the front cover again, insert and replace the three screws.

●Place the wheel rim on top of the washers, keeping it in place using all screws except the two for the Button Clusters (one screw for three-hole pattern, four screws for six-hole pattern).● Slide the Button Clusters in place, insert the remaining screws, tighten all evenly.

● Place the washers from the Button Cluster Pack (BCP; sold separately) on the holes where no Button Clusters will be mounted● Connect the P APM cables to the

correct sockets.

● Attach the front cover again, insert and replace the three screws.

● Attach Podium Advanced Paddle Module (P APM; sold separately) and tighten the mounting screws.

●PulloffthePodiumHubfrom the wheel base axle

● Compress and hold the Quick Release mechanism

● Insert the storage pin (recommended for long-term storage)

● Release the Quick Release mechanism

● Align wheel base axle to correct position

● Slide the Podium Hub onto the wheel base axle up to the mechanical limit

● Release the Quick Release mechanism

● Compress and hold the Quick Release mechanism