nayax installation guide - e-service...nayax vpos/onyx this is the wireless card reader. the vpos or...

[email protected] WWW.E-SERVICE.CO.UK01707 280 050

Nayax installation Guide

The complete guide to installing the Nayax wireless card reader

1

35

7

6

8

9

4

2

Nayax Installation Guide

2

Figure 1 - Installed Nayax Layout

1

2

4

5

7

8

9

6

3


3

Nayax VPOS/OnyxThis is the wireless card reader. The VPOS or Onyx

should be fixed to the outside of the machine in

easy access to customers.

For detailed information on fitting the VPOS/Onyx

unit, please refer to page 9.

Nayax AMIT 3The Nayax AMIT 3 is the central unit of the Nayax

system and connects the Nayax components

together. The AMIT 3 should be placed inside the

machine

I/O Connector CableThis cable plugs into the AMIT’s ‘I/O‘ socket and

connects it to the Nayax Interface Board. Please

note that the cable splits to include a plug that is

not used in most installations.

NAYAX Interface BoardThis small circuit board plugs into the coin mech

through the socket that is usually connected to the

machine’s main control board. It connects the Amit

to the coin mech, number meter and main board.

PL1 Main Board CableThis cable is attached to the machine’s main board

and is usually connected directly to the coin mech.

In the Nayax setup, the cable is plugged into the

interface board’s PL1 pin-socket.

Number MeterThis number meter attaches to the interface board

and records when a transaction is used. For detailed

instructions for manually attaching a number meter

to the interface board, please refer to page 5.

AntennaThe antenna screws into the top of the AMIT3 and

can be positioned internally to protect against van-

dalism or externally to maximise signal strength.

PL2 Wire HolesThe PL2 wire holes are used to connect the inter-

face board to the AMIT and number meter.

If manually connecting the I/O cable or number

meter to interface board, detailed instructions can

be found on page 4.

RJ45 / RJ6 Connector CableThis cable connects the external VPOS to the

internal AMIT 3. The cable must pass through the

hole made while fitting the VPOS.

For detailed information on fitting the VPOS unit,

please refer to page 9.

1

4

7

10

11

12

PL2

2

5

8

3

6

9

Wire Colour Wire Name PL2 Hole Number

Brown AC / DC + 3

Orange PULSE1\FUJI RXD 4

Blue EX PULSE INHIBIT 5

Green AC / DC - 7

Red GND 8

Yellow PULSE2\FUJI TXD Not used

Black VCC Not used


4

To correctly wire the Nayax Interface Board, please follow the diagram above to match the correct wires to the correct holes.

VPOS to Interface Board wiring guide

Figure 2

1

4

7

10

11

12

PL2

2

5

8

3

6

9

Wire Colour Wire Name PL2 Hole Number

Black (any wire) 10

Black (any wire) 11


5

To correctly wire the number meter, please follow the diagram above to match the correct wires to the correct holes.

Please note that the order of the wires is not important for the number meter.As long as one wire is placed in hole 10 and the other is placed in hole 11, the number meter should function correctly.

Number meter wiring guide

Figure 3


6

Figure 4

Figure 5

Figure 6

Thomas software updating guide

Access the Control ModuleOpen the Machine and locate the Control Module, as seen in figure 4. Remove the bill validator to gainaccess to the control module and open it’s hinged door.

Replace the software chipRemove the chip from the inside of the control module’s door, as seen circled in red in figure 5.Replace the old chip with the new software chip provided in the upgrade kit.

1.

2.


7

Figure 7

Figure 8

Enable 10p coins for testingOn the large circuit board on the opposite side, locate the four switches marked ‘S2’, as seen circled in red in figure 7. Flip the fourth switch to the on position, as seen in figure 8.

Test the newly activated software.Test the software by dropping a 10p coin, it should give change for the same value that the Nayax tap value should be, i.e £5, £10 or £20. Insert all other coins and notes and check the change given is correct.

If the change given is correct, close the control module, re-insert the note validator and proceed tosection 5. If the change is incorrect or you encounter other errors, replace the old software chip and call E-Service support on 01707 280 050.

3.

4.


8

Remove the plastic cover from the Thomas Machine doorUnscrew the four 7mm nuts that are circled in red in figure 9. Once the nuts are unscrewed, remove the plastic cover, as seen in figure 10.

5.

Figure 9

Figure 10


9

Place the provided template over the Thomas 3000Print out the template on page 15 or 16 of this guide, depending onwhether you are installing the VPOS or Onyx. Place the printed template over the Thomas machine, aligning the yellow arrow with the indent corner as seen in figure 12.

CAUTION: Remember to print without scaling the page and use the printed ruler toensure that the printout is correctly sized.

Drill through the faceplate as marked on the printed templateUse a center punch to mark the drill points as shown on the template.Drill holes for the screws and one large hole for the cable to pass though, sized according to the printed template

Optionally, you may remove the inner back plate and shorten it to the red line, rather than drilling

though it. Take care to remove the circuit board on the right of figure 13 before removing the plate.

1.

2.

VPOS wireless card reader mounting guide

Figure 13

Figure 12

Figure 11


10

Figure 15 Figure 16

Screw the VPOS/Onyx into the front of the machinePosition the VPOS/Onyx wireless card reader over the newly drilled holes and

screw it in from the back of the machine’s door, as seen in figure 16. Ensure

that the card reader is flush with the machine and correctly aligned before

tightening the screws.

4.

Insert the grommet for the connector cableOnce drilled, fit the grommet into the 22mm hole, as seen in figure 14.

3.

Figure 14


11

Position the AMIT 3 inside the machine and connect it to the VPOSPlace the AMIT inside the machine, using its magnetic back to attach it to a metal surface. Next, plug the VPOS/Onyx connection cable into the AMIT port marked ‘VPOS’, as in figure 18.

Connect the Nayax Interface Board to the AMIT 3Plug the the I/O cable into the AMIT’s port marked ‘I/O’, as seen in figure 20.If the Interface Board is not already connected to the I/O cable, please refer to page 4 for detailed instructions on how to wire them together.

6.

7.

AMIT 3 mounting guide

Figure 17

Figure 19

Figure 18

Figure 20


12

Plug the Interface Board into the coin mech and the main boardFind the cable connecting the machine’s main control board to the coin mech and unplug it. Plug the inter-face board into the same socket as in figure 22.

Take the ribbon cable that you just unplugged and plug it into the Interface Board. IMPORTANT: skip the first pin when plugging in the ribbon cable, as in figure 23.

8.

NAYAX Interface Board mounting guide

Figure 21

Figure 22

Figure 23


13

Mounting the aerial guide

Figure 24 Figure 25

Position the aerial on the machine.Position aerial on the machine. Positioning the aerial on the inside of the machine will protect against vandalism, but positioning the aerial externally will maximise signal strength. To position the aerial on the

outside, pass its wire into the hole on the back of the machine, as in figure 24.

Screw the aerial cable into the AMIT 3 unit.Find the copper end of the aerial cable and screw it onto the top left of the AMIT unit, as in figure 25.

5.

6.


14

Finishing up the installation

Figure 26 Figure 27

Secure the loose wiresUsing the sticky metal clamps included in the kit, tie down the loose cables into a preferred location,as seen in n figure 26.

Position the number meterPosition the number meter (used to record transaction numbers) in a preferred visible location,as seen in figure 27. If your Interface Board does not already have a number meter attached, please refer to page 5 for detailed instructions on how to wire them together.

Stick the contactless payment instruction labelFind the contactless payment instructions label that was included in the kit and attach it to the front of the machine in a visible location.

Turn on the Machine and contact E-ServiceTurn the power on to the machine and call E-Service on 01707 280 050. We will complete the installation

with you and test it remotely.

9.

10.

11.

12.

Print o

ut th

is pag

e o

n a sh

ee

t of A

4 pap

er.

Re

me

mb

er to

sele

ct “DO

NO

T S

CA

LE

” in yo

ur

printe

r’s settin

gs

IMP

OR

TAN

T: Use

the

printe

d ru

ler at th

e

bo

ttom

of th

e p

age

to ch

eck th

at the

gu

ide

h

as printe

d at th

e co

rrect size

.

Cu

t ou

t the

gu

ide

alon

g th

e d

otte

d b

lue

line

s an

d p

lace it ove

r the

mach

ine

as see

n o

n

pag

e 9

.

Use

a cente

r pu

nch

to m

ark the

five p

oints to

d

rill as marke

d o

n th

e g

uid

e.

Drill fo

ur 6

mm

ho

les fo

r the

screws an

d o

ne

22m

m h

ole

for th

e cab

le to

pass th

ou

gh

.

Nayax V

PO

S fittin

g g

uid

e

15

67mm

93mm

52mm

87mm

70mm

125mm

CUT HERE

CUT HERE

CUT HERE CUT HERE

22mm

Hole

6mm

Hole

6mm

Hole

6mm

Hole

6mm

Hole

93mm

87mm

CUT HERE

CUT HERE

CUT HERE CUT HERE

5mm

Hole5m

mHole

5mm

Hole

20mm

Hole

90mm

90mm

39mm

63mm

58mm

29mm

93mm

Print o

ut th

is pag

e o

n a sh

ee

t of A

4 pap

er.

Re

me

mb

er to

sele

ct “DO

NO

T S

CA

LE

” in yo

ur

printe

r’s settin

gs

IMP

OR

TAN

T: Use

the

printe

d ru

ler at th

e

bo

ttom

of th

e p

age

to ch

eck th

at the

gu

ide

h

as printe

d at th

e co

rrect size

.

Cu

t ou

t the

gu

ide

alon

g th

e d

otte

d b

lue

line

s an

d p

lace it ove

r the

mach

ine

as see

n o

n

pag

e 9

.

Use

a cente

r pu

nch

to m

ark the

fou

r po

ints to

drill as m

arked

on

the

gu

ide

.

Drill fo

ur 5m

m h

ole

s for th

e screw

s and

on

e

20m

m h

ole

for th

e cab

le to

pass th

ou

gh

.

Nayax O

nyx fittin

g g

uid

e

16

[email protected]

WWW.E-SERVICE.CO.UK

01707 280 050

Contact us

If you have any difficulties with installing your Nayax device,

do not hesitate to contact E-Service by phone or email.

The E-Service Support Team and our expert engineers are

ready to help you get your Nayax payment system up and

running and to help you through any issues that might occur.

nayax installation guide - e-service...nayax vpos/onyx this is the wireless card reader. the vpos or...

Documents