nanawall matching windows and doors table of...
TRANSCRIPT
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com i
NanaWall® Matching Windows and Doors | Table of Contents
Matching Windows and Doors
Cross Sections and Maximum Frame Charts
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
NanaWall French Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Performance and Testing Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Maximum Frame Height Chart
Fixed Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Tilt Turn Window / Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
NanaWall® WA68 - Aluminum Clad Wood Fixed Panel and Tilt Turn Window / Door . . .9
NanaWall® WD68 - Wood Framed Fixed Panel and Tilt Turn Window / Door . . . . . . . . .11
NanaWall® SL48 - Aluminum Framed Fixed Panel and Tilt Turn Window / Door . . . . . .13
NanaWall® SL88 - Thermally Broken Aluminum Framed Fixed Panel and
Tilt Turn Window / Door with HVHZ Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
NanaWall® SL68 - Thermally Broken Aluminum Framed Fixed Panel and
Tilt Turn Window / Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 1
NanaWall® Matching Windows and Doors | Introduction
Coordinated Walls
Available are matching systems in aluminum-clad wood, wood,
standard aluminum and thermally broken aluminum.
Depending on sizes and wind load requirements, matching
systems can be mulled (with appropriate structural support) with
folding and individual panel sliding system.
Fixed Windows and Storefront
Fixed units are available for transoms above a folding or
individual panel sliding unit. Center lines can be lined up.
Sidelites are available with frame extenders so that horizontal
glass lines are approximately the same.
Complete storefronts are also available with a combination of
mulled units.
NanaWall® Tilt Windows and Doors
Available are tilt-turn windows, tilt-turn doors and tilt-only hopper
windows.
These systems are engineered to provide high weather
resistance and structural performance, suitable for many high-rise
structures and buildings in hurricane and other areas.
Florida Approval
SL88 thermally broken aluminum framed tilt turn window with
frame size of 48" wide x 72" high is Florida state wide approved
with Product Approval number FL16047. It is also approved for
use in the high velocity hurricane zone (HVHZ) with impact
glass. This information with limitations can be viewed at www.
floridabuilding.org.
Performance Testing
The tested sample unit of the SL 68 thermally broken aluminum
framed tilt turn window met the performance requirements of
AAMA DAW-C90 1219 x 1829 (48x72) /DA-C100 48x72 rating.
The tested sample unit of the SL 88 thermally broken aluminum
framed tilt turn window met the performance requirements of
AAMA DAW-C70 1219 x 1829 (48x72)/DA-C70 48x72 rating.
The tested sample unit of the WA68 aluminum-clad wood framed
tilt turn window met the performance requirements of AAMA
DAW-C50 1122x1822 (48x72).
The tested sample unit of the WD 68 wood framed tilt turn
window met the performance requirements of AAMA DAW-C70
1220x1828 (48x72).
See Performance pages for details.
Benefits of NanaWall Tilt Systems
With tilt-turn hardware, large size operable openings are possible.
Tilts Inward for Safe Ventilation. The tilt position opens up from
the top, tilting in a few inches, for safe ventilation.
Turns Inward for Easy Cleaning. With the turn position, the
window swings in on its hinges to make cleaning the outside
surface easy.
For units used as transoms, tilt-only hopper windows can be
supplied with operators so that high units can be easily opened
and closed.
NOTICE
For mulled fixed or tilt turn units or a combination of different
units, please consult with a qualified structural engineer to
determine, based on project design wind loads and other
requirements, if any structural stiffeners are needed between
units.
2 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Introduction
Technical Description
The corresponding closest system match to NanaWall folding/sliding systems are as follows:
Profile and Finish Options
For WD 68 and WA 68 systems, standard woods available are Douglas Fir, Pine, or Meranti. Other woods are also available.
Frames and panels have a sanding sealer or a base coat applied or for WA 68 system only, with one additional clear coat; see
“Wood Finish Options” in the General Introduction.
Standard aluminum finishes for the WA68, SL48 and SL88 systems are clear anodized and the 50 finishes shown in the
NanaWall Powder Coating Finish Chart in the front of this binder. Powder coated finishes can be chosen from a range of over
two hundred RAL colors; see “Aluminum Finish Options” in the General Introduction.
Glazing
Units are supplied glazed with double clear insulating safety, insulating Low-E safety glass, single (for SL48 and WD 68 sys-
tems only), other high performing safety glass such as triple glazing, Heat Mirror, special tint, etc., or other glass on request.
Hinge Cover Options
Covers for hinges can be white, brown or silver.
Handle Options
Standard: Stainless steel in brushed satin or black titanium finishes.
Optional: Nylon available in white, dark brown or gray color or solid brass available in white, oil rubbed brass or satin
nickel finishes.
See "Hardware" in the General Introduction for other options.
NanaWall® French Doors
NanaWall® French doors are available as single doors or pairs. Very narrow stiles
and rails are possible.
NanaWall® French doors use exactly the same profiles and hardware as the
matching NanaWall® folding system. Hence, the same size charts, glazing options,
wood/finish options and finish hardware options as the matching NanaWall®
folding system are applicable.
The same testing performance results also apply (within a folding system, with an
odd number of panels stacking to one side, the last panel is a swing door).
For aluminum-clad, wood framed French doors, see WA67.
For wood framed French doors, see WD66 and WD65.
For standard aluminum framed French doors, see SL45.
For thermally broken aluminum framed French doors, see SL60 and SL70.
For Miami Dade / AAMA hurricane thermally broken aluminum framed French
doors, see SL73.
For structurally glazed aluminum framed French doors, see SL82.
Folding/sliding system Corresponding matching fixed/tilt turn system
WA67 WA68
WD65, WD66, HSW66 WD68
SL45, HSW45 SL48
SL60, HSW60 SL68
SL70 SL88
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 3
NanaWall® Matching Windows and Doors | Performance
Performance Testing Results
Type of Test Result
*Air Infiltration: ASTM E-283, cfm/ft2 @1.6 psf (75 Pa): 0.04 (.20 L/s/m2)
@6.20 psf (300 Pa): 0.11 (.56 L/s/m2)
*Water Penetration: ASTM E547 and E331 No uncontrolled water entry @ 13.5 psf (645 Pa)
* Structural Load Deflection ASTM E-330: Pass
Note that the structural test pressures were 50% higher than the
design pressures.
Design Pressure Positive: @100 psf (4800 Pa)
Design Pressure Negative: @110 psf (5270 Pa)
*Forced Entry Resistance In accordance with ASTM F 588
* Excerpts of results of a 4’0”W x 6’0”H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing labo-
ratory in August 2006, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05 and AAMA/NWWDA 101/I.S.2-97 standards. The
sample tested met the performance requirements for a DAW-C90 1219 x 1829 (48 x 72)/DA-C100 48x72 rating.
Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4’0” W x 6’0” H
Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/
or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for
restrictions.
Please also note that chart is only applicable for units with referenced NanaWall supplied locking.
250
245
240
235
230
225
220
215
210
205
200
195
190
185
180
175
170
165
160
155
150
145
140
135
130
125
120
115
110
105
100
95
90
85
1’11’
2’3”
2’7”
2’11”
3’3”
3’7”
3’11”
4’3”
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Fram
e W
idth
Frame HeightSee Maximum Frame Size Chart for Possible Sizes
Negative Design Pressure
250
245
240
235
230
225
220
215
210
205
200
195
190
185
180
175
170
165
160
155
150
145
140
135
130
125
120
115
110
105
100
95
90
85
1’11’
2’3”
2’7”
2’11”
3’3”
3’7”
3’11”
4’3”
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Fram
e W
idth
Frame HeightSee Maximum Frame Size Chart for Possible Sizes
Positive Design Pressure
SL68 Thermally Broken Aluminum Framed Tilt Turn Window/Door
4 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
Performance Testing Results
Type of Test Result
*Air Infiltration: Protocol TAS 202 and ASTM E-283, cfm/ft2
@1.60 psf (75 Pa): 0.09
@6.20 psf (300 Pa): 0.25
*Water Penetration: Protocol TAS 202, ASTM E547 and E331 No uncontrolled water entry @ 13.5 psf (645 Pa)
* Structural Load Deflection Protocol TAS 202 and ASTM E-330:
Pass
Note that the structural test pressures were 50% higher than the
design pressures.
Design Pressure Positive: @70 psf (3350 Pa)
Design Pressure Negative: @100 psf (4785 Pa)
Missile Impact & Cycling: Protocols TAS 201 & 203,
ASTM E 1886 and E 1996
WITH 1 1/8" INSULATED IMPACT GLASS
Design Pressure Positive: @ 90 psf (4300 Pa)
Design Pressure Negative: @ 120 psf (5260 Pa)
*Forced Entry Resistance In accordance with ASTM F 588
* Excerpts of results of three separate units with sizes of 4’0”W x 6’0”H tested by Architectural Testing, Inc., Fresno, CA, an inde-
pendent testing laboratory, in October 2010.
Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4’0” W x 6’0” H
Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/
or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for
restrictions.
Please also note that chart is only applicable
for units with referenced NanaWall supplied
locking.
SL88 Thermally Broken Aluminum Framed Tilt Turn Window/Door High Velocity Hurricane Zone (HVHZ) rated with Impact Glass with FL Product Approval # 16047
NanaWall® Matching Windows and Doors | Performance
90
88
86
84
82
80
78
76
74
72
70
68
66
64
62
60
58
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Frame Height
See Maximum Frame Size Chart for Possible Sizes
2’7”
2’11”
3’7”
3’11”
4’3”
Fram
e W
idth
3’3”
120
118
116
114
112
110
108
106
104
102
100
98
96
94
92
90
88
86
84
82
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Frame Height
See Maximum Frame Size Chart for Possible Sizes
Fram
e W
idth
2’11”
3’7”
3’11”
4’3”
3’3”
Positive Design Pressure Negative Design Pressure
Max.
limited to
cycling
pressure
Max.
limited to
cycling
pressure
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 5
Performance Testing Results
Type of Test Result
*Air Infiltration: ASTM E-283, cfm/ft2 @1.6 psf (75 Pa): 0.01 (.1 L/s/m2)
@6.20 psf (300 Pa): 0.15 (.8 L/s/m2)
*Water Penetration: ASTM E547 and E331 No uncontrolled water entry @ 12 psf ( 580 Pa)
* Structural Load Deflection ASTM E-330: Pass
Note that the structural test pressures were 50% higher than the
design pressures.
Design Pressure Positive: @50 psf (2400 Pa)
Design Pressure Negative: @70 psf (3360 Pa)
*Forced Entry ResistanceIn accordance with ASTM F 588
- Grade 20 & CAWM 301
* Excerpts of results of a 4’0”W x 6’0”H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing labo-
ratory in January 2008, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05 standard. The sample tested met the performance
requirements for a DAW-C50 1220 x 1822 (48 x 72) rating.
Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/
or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for
restrictions.
145
140
135
130
125
120
115
110
105
100
95
90
85
80
75
70
65
60
55
50
1’11’
2’3”
2’7”
2’11”
3’3”
3’7”
3’11”
4’3”
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Fram
e W
idth
Frame HeightSee Maximum Frame Size Chart for Possible Sizes
Negative Design Pressure
105
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
20
15
1’11’
2’3”
2’7”
2’11”
3’3”
3’7”3’11”4’3”
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Fram
e W
idth
Frame HeightSee Maximum Frame Size Chart for Possible Sizes
Positive Design Pressure
Please also note that chart is only applicable
for units with referenced NanaWall supplied
locking.
Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4’0” W x 6’0” H
WA68 Aluminum Clad Wood Framed Tilt Turn Window/Door
NanaWall® Matching Windows and Doors | Performance
6 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/
or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for
restrictions.
250
245
240
235
230
225
220
215
210
205
200
195
190
185
180
175
170
165
160
155
150
145
140
135
130
125
120
115
110
105
100
95
90
85
1’11’
2’3”
2’7”
2’11”
3’3”
3’7”
3’11”
4’3”
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Fram
e W
idth
Frame HeightSee Maximum Frame Size Chart for Possible Sizes
Negative Design Pressure
145
140
135
130
125
120
115
110
105
100
95
90
85
80
75
70
65
60
55
50
1’11’
2’3”
2’7”
2’11”
3’3”
3’7”
3’11”
4’3”
3’0” 3’6” 4’0” 4’6” 5’0” 5’6” 6’0” 6’6” 7’0” 7’6” 8’0” 8’6”
Allow
able
Desi
gn W
ind L
oadin
g -
PSF
Fram
e W
idth
Frame HeightSee Maximum Frame Size Chart for Possible Sizes
Positive Design Pressure
Please also note that chart is only applicable
for units with referenced NanaWall supplied
locking.
Performance Testing Results
Type of Test Result
*Air Infiltration: ASTM E-283, cfm/ft2
@1.60 psf (75 Pa): 0.01 (.1 L/s/m2)
@6.20 psf (300 Pa): 0.01 (.1 L/s/m2)
*Water Penetration: ASTM E547 and E331 No uncontrolled water entry @ 13.5 psf (645 Pa)
* Structural Load Deflection ASTM E-330: Pass
Note that the structural test pressures were 50% higher than the
design pressures.
Design Pressure Positive: @70 psf (3360 Pa)
Design Pressure Negative: @120 psf (5745 Pa)
*Forced Entry ResistanceIn accordance with ASTM F 588
- Grade 20 & CAWM 301
* Excerpts of results of a 4’0”W x 6’0”H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing
laboratory in January 2008, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05 standard. The sample tested met the perfor-
mance requirements for a DAW-C70 1220 x 1828 (48 x 72) rating.
Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4’0” W x 6’0” H
WD68 Wood Framed Tilt Turn Window/Door
NanaWall® Matching Windows and Doors | Performance
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 7
NanaWall® Matching Windows and Doors | Size Chart
9’10” (3000)
9’2” (2800)
8’6” (2600)
7’10” (2400)
7’2” (2200)
6’6” (2000)
5’11” (1800)
5’3” (1600)
4’7” (1400)
3’11” (1200)
3’3” (1000)
Any custom size is possible up to the maximum size shown.
NanaWall® Maximum Frame Size Chart – Fixed Panel
WA68, WD68, SL48, SL68, SL88
Fra
me H
eig
ht
of
Un
itNOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters
Frame Width of Unit
1’11” 2’7” 3’3” 3’11” 4’7” 5’3” 5’11” 6’6” 7’2”
(600) (800) (1000) (1200) (1400) (1600) (1800) (2000) (2200)
Solid dark line on chart indicates maximum frame height possible
for a given maximum frame width.
The maximum size limits shown are based on the weight of a unit that
has a net glass thickness of 5/16” (8mm). The composition of standard
insulated glass is 5/32” glass/air space/ 5/32” glass. For other net glass
thicknesses, this maximum size chart may not apply.
8 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Size Chart
NanaWall® Maximum Frame Size Chart – Tilt Turn Window/Door
WA68, WD68, SL48, SL68, SL88
8’2” (2500)
7’10” (2400)
7’7” (2300)
7’3” (2200)
6’11” (2100)
6’7” (2000)
6’3” (1900)
5’11” (1800)
5’7” (1700)
5’3” (1600)
4’11” (1500)
4’7” (1400)
4’3” (1300)
3’11” (1200)
3’7” (1100)
3’3” (1000)
Any custom size is possible up to the maximum size shown.F
ram
e H
eig
ht
of
Un
it
NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters
Frame Width of Unit
1’11” 2’3” 2’7” 2’11” 3’3” 3’7” 3’11” 4’3” 4’7” 4”11” 5’3”
(600) (700) (800) (900) (1000) (1100) (1200) (1300) (1400) (1500) (1600)
Solid dark line on chart indicates maximum frame height possible for a given
maximum frame width.
The maximum size limits shown are based on the weight of a unit that has a net glass
thickness of 5/16” (8mm). The composition of standard insulated glass is 5/32” glass/
air space/ 5/32” glass. For other net glass thicknesses, this maximum size chart may not
apply.
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 9
NanaWall® Matching Windows and Doors
NanaWall® WA68 Fixed Panel All Cross-Sectional Views Are Half Size
Vertical Cross-Section
Horizontal Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
Wood frame extenders are
available to approximately align
glass sight lines to adjacent
folding or sliding systems.
10 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors
NanaWall® WA68 Tilt Turn Window(Available as a single window or as a pair. In a pair, only
one panel can tilt). All Cross-Sectional Views Are Half
Size.
Horizontal Cross-Section
Vertical Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 11
NanaWall® Matching Windows and Doors
NanaWall® WD68 Fixed Panel All Cross-Sectional Views Are Half Size
Vertical Cross-Section
Horizontal Cross-Section
Wood frame extenders are
available to approximately align
glass sight lines to adjacent
folding or sliding systems.
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
12 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors
NanaWall® WD68 Tilt Turn Window(Available as a single window or multiple unit). All Cross-
Sectional Views Are Half Size
Vertical Cross-Section
Horizontal Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 13
NanaWall® Matching Windows and Doors
NanaWall® SL48 Fixed Panel All Cross-Sectional Views Are Half Size
Vertical Cross-Section
Horizontal Cross-Section
Aluminum frame extenders are
available to approximately align
glass sight lines to adjacent folding
or sliding systems.
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
14 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors
NanaWall® SL48 Tilt Turn Window
All Cross-Sectional Views Are Half Size. (Available as a
single window or as a pair. In a pair, only one panel can
tilt.)
Vertical Cross-Section
Horizontal Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 15
NanaWall® Matching Windows and Doors
NanaWall® SL88 Thermally Broken Fixed Panel
All Cross-Sectional Views Are Half Size.
Vertical Cross-Section
Horizontal Cross-Section
Aluminum frame extenders are
available to approximately align
glass sight lines to adjacent folding
or sliding systems.
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
16 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors
NanaWall® SL88 Thermally Broken
Tilt Turn Window
(Available as a single window or as a pair. In a pair, only one panel
can tilt.) All Cross-Sectional Views Are Half Size.
Vertical Cross-Section
Horizontal Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
High Velocity Hurricane Zone (HVHZ) rated with Impact Glass with FL Product Approval # 16047
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 17
NanaWall® Matching Windows and Doors
NanaWall® SL68 Thermally Broken Fixed Panel
All Cross-Sectional Views Are Half Size.
Vertical Cross-Section
Horizontal Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
Aluminum frame extenders are
available to approximately align
glass sight lines to adjacent folding
or sliding systems.
18 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors
NanaWall® SL68 Thermally Broken
Tilt Turn Window
(Available as a single window or as a pair.
In a pair, only one panel can tilt.)
All Cross-Sectional Views Are Half Size.
Horizontal Cross-Section
Vertical Cross-Section
EXTERIOR INTERIOR
EXTERIOR
INTERIOR
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 19
Guide Specifications | NanaWall® Matching Windows and Doors
Guide Specifi cations - Section 085200:
NanaWall® SL88 – Thermally Broken Aluminum Framed Dual Action Tilt Turn Window
PART 1 – GENERAL
1.01 SUMMARY
A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping,
glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown
on drawings and specifi ed herein, with NanaWall® SL88, the Thermally Broken Aluminum Framed Dual Action Tilt
Turn Window as supplied by NANA WALL SYSTEMS, INC.
1.02 REFERENCES
A. FL Building Code Compliance Offi ce Protocol:
1. TAS 201, Impact Test Procedures
2. TAS 202, Criteria for Testing Impact and Non Impact Resistant Building Envelope Components Using Uniform
Static Air Pressure
3. TAS 203, Criteria for Testing Products Subject to Cyclic Wind Pressure Loading.
A. American Architectural Manufacturers Association (AAMA):
4. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights.
5. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum.
6. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic
Coatings on Aluminum Extrusions and Panels..
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Build-
ings.
C. American Society for Testing and Materials (ASTM):
1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by
Uniform Static Air Pressure Difference.
2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform
Static Air Pressure Difference.
3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain
Walls by Uniform Static Air Pressure Difference.
4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static
Air Pressure Differential.
5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies.
D. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
1.03 SUBMITTALS
A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and
handle height.
B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's
Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and
B.
C.
D.
E.
1.
2.
3.
20 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
completion date, type and size of unit installed.
1.04 QUALITY ASSURANCE
A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufac-
turer with at least 25 years experience in providing fenestration systems in the North American market.
1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard.
2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005
standard.
B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/
WDMA/CSA 101/I.S.2/A440 Testing results to include air infi ltration in accordance with ASTM E 283, water penetra-
tion in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330 and forced
entry in accordance with ASTM F 588.
C. Performance Criteria with Impact Glass: The SL88 is approved for High Velocity Hurricane Zone (HVHZ) with Impact
Glass with FL Product Approval # 16047
** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis
charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures
specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project).
See manufacturer's latest published data.
D. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestra-
tion products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully
completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers
of General Contractor and Owner's contact person.
1.05 WARRANTY
A. Provide manufacturer's standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two
years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer.
1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the
following:
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material
under cover, protected from weather and construction activities.
B. Do not use forced heat to dry out building.
C. Store fl at in dry, well ventilated area out of direct sunlight.
PART 2 – PRODUCTS
2.01 SUPPLIER
A. NANA WALL SYSTEMS, INC. - SL88
100 Meadow Creek Drive, Corte Madera, CA 94925
Toll Free: (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0312
Website: www.nanawall.com
Email: [email protected]
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 21
Guide Specifications | NanaWall® Matching Windows and Doors
B. Other suppliers equal to the specifi ed product must submit substitution request two weeks before bid for prior
approval.
2.02 MATERIALS
A. Frame and Sash: From manufacturer’s standard profi les, provide frame, sash and glazing stops with dimensions
shown on drawings.
1. Provide Sash with: Standard one lite
[OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel]
[OR with simulated divided lites in pattern as shown on drawings].
2. Aluminum Extrusion: Extrusions with nominal thickness of .078” (2.0 mm). Alloy specifi ed as AIMgSi0.5 with
strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated
conforming to AAMA 2604
3. Thermally broken with ¾”-15/16” (20-24 mm) polyamide plastic reinforced with glass fi bers with additional insulat-
ing foam.
4. Aluminum Finish:
Select from NanaWall Powder Coating Finish Chart
[OR clear anodized]
[OR dark bronze anodized]
[OR select from range of RAL high gloss powder coated fi nishes available from manufacturer]
[OR select from range of RAL matte powder coated fi nishes available from manufacturer]
[OR select from range of Wood Grain powder coated fi nish]
[OR custom fi nish].
Same [OR different] fi nishes on inside and outside.
B. Glass:
1. Provide manufacturer’s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only.
Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120
15/16” (24 mm) insulating clear safety
[OR 15/16” (24 mm) double glazed insulating argon fi lled Low-E safety]
[OR 1 ½” (38 mm triple glazed insulating argon fi lled Low-E safety]
[OR other glass available from manufacturer].
2. Provide manufacturer’s standard glass spacers. Provide without capillary tubes [OR with capillary tubes].
C. Tilt Turn Hardware
1. Provide manufacturer’s standard cam type multipoint locking mechanism.
a. The concealed multipoint locking mechanism shall be driven by a single locking handle.
2. Provide manufacturer’s standard hinges, pins, strikes, and limit stays.
3. Handles:
Stainless steel window handles in a titanium black fi nish
[OR stainless steel window handles in a brushed satin fi nish]
SPECIFIER’S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other
suppliers.
Provide handle height centered [OR at 41 3/8” from bottom of panel] [OR as specifi ed from bottom of
22 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
panel].
D. Weather stripping: Provide manufacturer’s standard double layer EPDM
2.03 FABRICATION
A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles,
glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory
pre-assemble as is standard for manufacturer and ship with all components and installation instructions.
B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns
and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right]
2.04 ACCESSORIES (Edit for project requirements.)
A. Provide insect screen. Mesh in gray [Or black]
Provide screen frame in aluminum:
White powder coated
[OR clear anodized]
[OR dark bronze anodized]
[OR powder coated select from range of RAL powder coated fi nishes available from manufacturer].
B. Provide other side lites, transoms as per drawings provided.
PART 3 – EXECUTION
3.01 ERECTION
A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity
of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no
unevenness, bowing, or bumps on the fl oor.
C. Installation of units constitutes acceptance of existing conditions.
3.02 INSTALLATION
A. Install frame in accordance with manufacturer’s recommendations and installation instructions. Properly fl ash and
waterproof around the perimeter of the opening.
B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level,
straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with
other work.
C. Install sash and handles in accordance with manufacturer’s recommendations and installation instructions.
D. If necessary, adjust hardware for proper operation.
E. Accessories: Screens; install in accordance with screen manufacturer’s recommendations and installation
instructions.
END OF SECTION
DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to,
compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not intended
to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the particular require-
ments of a specifi c construction project.
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 23
Guide Specifications | NanaWall® Matching Windows and Doors
Guide Specifi cations - Section 085200
NanaWall® SL48 – Aluminum Framed Dual Action Tilt Turn Window
PART 1 – GENERAL
1.01 SUMMARY
A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping,
glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown
on drawings and specifi ed herein, with NanaWall® SL48, the Aluminum Framed Dual Action Tilt Turn Window as
supplied by NANA WALL SYSTEMS, INC.
1.02 REFERENCES
A. American Architectural Manufacturers Association (AAMA):
1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights.
2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum.
3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic
Coatings on Aluminum Extrusions and Panels.
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings.
C. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
1.03 SUBMITTALS
A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and
handle height.
B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's
Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and
completion date, type and size of unit installed.
1.04 QUALITY ASSURANCE
A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufac-
turer with at least 25 years experience in providing fenestration systems in the North American market.
1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard.
2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005
standard.
B. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestra-
tion products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully
completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers
of General Contractor and Owner's contact person.
1.05 WARRANTY
A. Provide manufacturer's standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two
years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer.
1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the
following:
24 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material
under cover, protected from weather and construction activities.
B. Do not use forced heat to dry out building.
C. Store fl at in dry, well ventilated area out of direct sunlight.
PART 2 – PRODUCTS
2.01 SUPPLIER
A. NANA WALL SYSTEMS, INC. - SL48
100 Meadow Creek Drive, Corte Madera, CA 94925
Toll Free: (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0312
Website: www.nanawall.com
Email: [email protected]
B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior
approval.
2.02 MATERIALS
A. Frame and Sash: From manufacturer’s standard profi les, provide frame, sash and glazing stops with dimensions
shown on drawings.
1. Provide Sash with: Standard one lite
[OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel]
[OR with simulated divided lites in pattern as shown on drawings].
2. Aluminum Extrusion: Extrusions with nominal thickness of .078” (2.0 mm). Alloy specifi ed as AIMgSi0.5 with
strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611.98 or powder coated
conforming to AAMA 2604
3. Aluminum Finish:
Select from NanaWall Powder Coating Finish Chart
[OR dark bronze anodized]
[OR clear anodized]
[OR select from range of RAL high gloss powder coated fi nishes available from manufacturer]
[OR select from range of RAL matte powder coated fi nishes available from manufacturer]
[OR custom fi nish].
B. Glass:
1. Provide manufacturer’s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only.
Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120
1/4” (6 mm) tempered
[OR ¼” (6 mm) laminated]
[OR ¾” (20 mm) insulating clear safety]
[OR ¾” (20 mm) double glazed insulating argon fi lled Low-E safety]
[OR other glass available from manufacturer].
2. For insulated units, provide manufacturer’s standard glass spacers. Provide without capillary tubes [OR with
capillary tubes].
C. Tilt Turn Hardware
1. Provide manufacturer’s standard cam type multipoint locking mechanism.
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 25
Guide Specifications | NanaWall® Matching Windows and Doors
a. The concealed multipoint locking mechanism shall be driven by a single locking handle.
2. Provide manufacturer’s standard hinges, pins, strikes, and limit stays.
3. Handles:
Stainless steel window handles in a titanium black fi nish
[OR stainless steel window handles in a brushed satin fi nish]
SPECIFIER’S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other
suppliers.
D. Provide handle height centered [OR at 41 3/8” from bottom of panel] [OR as specifi ed from bottom of panel].
E. Weather stripping: Provide manufacturer’s standard double layer EPDM
2.03 FABRICATION
A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles,
glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory
pre-assemble as is standard for manufacturer and ship with all components and installation instructions.
B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns
and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right]
2.04 ACCESSORIES (Edit for project requirements.)
A. Provide insect screen. Mesh in gray [Or black]
Provide screen frame in aluminum:
White powder coated
[OR clear anodized]
[OR dark bronze anodized]
[OR powder coated select from range of RAL powder coated fi nishes available from manufacturer].
B. Provide other side lites, transoms as per drawings provided.
PART 3 – EXECUTION
3.01 ERECTION
A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity
of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no
unevenness, bowing, or bumps on the fl oor.
C. Installation of units constitutes acceptance of existing conditions.
3.02 INSTALLATION
A. Install frame in accordance with manufacturer’s recommendations and installation instructions. Properly fl ash and
waterproof around the perimeter of the opening.
B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level,
straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with
other work.
C. Install sash and handles in accordance with manufacturer’s recommendations and installation instructions.
D. If necessary, adjust hardware for proper operation.
E. Accessories: Screens; install in accordance with screen manufacturer’s recommendations and installation
instructions.
END OF SECTION
26 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited
to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not
intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the par-
ticular requirements of a specifi c construction project.THIS PAGE BLANK
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 27
Guide Specifications | NanaWall® Matching Windows and Doors
Guide Specifi cations - Section 085200
NanaWall® SL68 Thermally Broken Aluminum Framed Dual Action Tilt Turn Window
PART 1 – GENERAL
1.01 SUMMARY
A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping,
glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown
on drawings and specifi ed herein, with NanaWall® SL68, the Thermally Broken Aluminum Framed Dual Action Tilt
Turn Window as supplied by NANA WALL SYSTEMS, INC.
1.02 REFERENCES
A. American Architectural Manufacturers Association (AAMA):
1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights.
2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum.
3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic
Coatings on Aluminum Extrusions and Panels..
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Build-
ings.
C. American Society for Testing and Materials (ASTM):
1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by
Uniform Static Air Pressure Difference.
2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform
Static Air Pressure Difference.
3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain
Walls by Uniform Static Air Pressure Difference.
4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static
Air Pressure Differential.
5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies.
D. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
1.03 SUBMITTALS
A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and
handle height.
B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's
Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and
completion date, type and size of unit installed.
1.04 QUALITY ASSURANCE
A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufac-
turer with at least 25 years experience in providing fenestration systems in the North American market.
1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard.
2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005
standard.
28 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/
WDMA/CSA 101/I.S.2/A440-0 Testing results to include air infi ltration in accordance with ASTM E 283, water
penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330
and forced entry in accordance with ASTM F 588.
** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis
charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures
specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project).
See manufacturer's latest published data.
C. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestra-
tion products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully
completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers
of General Contractor and Owner's contact person.
1.05 WARRANTY
A. Provide manufacturer's standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two
years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer.
1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the
following:
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material
under cover, protected from weather and construction activities.
PART 2 – PRODUCTS
2.01 SUPPLIER
A. NANA WALL SYSTEMS, INC. - SL68
100 Meadow Creek Drive, Corte Madera, CA 94925
Toll Free: (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0312
Website: www.nanawall.com
Email: [email protected]
B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior
approval.
2.02 MATERIALS
A. Frame and Sash: From manufacturer’s standard profi les, provide frame, sash and glazing stops with dimensions
shown on drawings.
1. Provide Sash with: Standard one lite
[OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel]
[OR with simulated divided lites in pattern as shown on drawings].
2. Aluminum Extrusion: Extrusions with nominal thickness of .078” (2.0 mm). Alloy specifi ed as AIMgSi0.5 with
strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated
conforming to AAMA 2604
3. Thermally broken with ¾”-15/16” (20-24 mm) polyamide plastic reinforced with glass fi bers with additional
insulating foam.
4. Aluminum Finish:
Select from NanaWall Powder Coating Finish Chart
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 29
Guide Specifications | NanaWall® Matching Windows and Doors
[OR dark bronze anodized]
[OR clear anodized]
[OR select from range of RAL high gloss powder coated fi nishes available from manufacturer]
[OR select from range of RAL matte powder coated fi nishes available from manufacturer]
[OR Wood Grain Finish]
Same [OR different] fi nishes on inside and outside.
[OR custom fi nish].
B. Glass:
1. Provide manufacturer’s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only.
Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120
15/16” (24 mm) insulating clear safety
[OR 15/16” (24 mm) double glazed insulating argon fi lled Low-E safety]
[OR 1 ½” (38 mm triple glazed insulating argon fi lled Low-E safety]
[OR other glass available from manufacturer].
2. For insulated units, provide manufacturer’s standard glass spacers. Provide without capillary tubes [OR with
capillary tubes].
C. Tilt Turn Hardware
1. Provide manufacturer’s standard cam type multipoint locking mechanism.
a. The concealed multipoint locking mechanism shall be driven by a single locking handle.
2. Provide manufacturer’s standard hinges, hinges pins, strikes, and limit stays.
3. Handles:
Stainless steel window handles in a titanium black fi nish
[OR stainless steel window handles in a brushed satin fi nish]
SPECIFIER’S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other
suppliers.
D. Provide handle height centered [OR at 41 3/8” from bottom of panel] [OR as specifi ed from bottom of panel].
E. Weather stripping: Provide manufacturer’s standard double layer EPDM
2.03 FABRICATION
A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles,
glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory
pre-assemble as is standard for manufacturer and ship with all components and installation instructions.
B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns
and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right]
2.04 ACCESSORIES (Edit for project requirements.)
A. Provide insect screen. Mesh in gray [Or black]
Provide screen frame in aluminum:
White powder coated
[OR clear anodized]
[OR dark bronze anodized]
[OR powder coated select from range of RAL powder coated fi nishes available from manufacturer].
30 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
B. Provide other side lites, transoms as per drawings provided.
PART 3 – EXECUTION
3.01 ERECTION
A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity
of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no
unevenness, bowing, or bumps on the fl oor.
C. Installation of units constitutes acceptance of existing conditions.
3.02 INSTALLATION
A. Install frame in accordance with manufacturer’s recommendations and installation instructions. Properly fl ash and
waterproof around the perimeter of the opening.
B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level,
straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with
other work.
C. Install sash and handles in accordance with manufacturer’s recommendations and installation instructions.
D. If necessary, adjust hardware for proper operation.
E. Accessories: Screens; install in accordance with screen manufacturer’s recommendations and installation
instructions.
END OF SECTION
DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited
to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not
intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the par-
ticular requirements of a specifi c construction project.
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 31
Guide Specifications | NanaWall® Matching Windows and Doors
Guide Specifications - Section 085200
NanaWall® WA68 Aluminum Clad Wood Framed Dual Action Tilt Turn Window
PART 1 – GENERAL
1.01 SUMMARY
A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping,
glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown
on drawings and specifi ed herein, with NanaWall® WA68, the Aluminum Clad Wood Framed Dual Action Tilt Turn
Window as supplied by NANA WALL SYSTEMS, INC.
1.02 REFERENCES
A. American Architectural Manufacturers Association (AAMA):
1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights.
2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum.
3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic
Coatings on Aluminum Extrusions and Panels.
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings.
C. American Society for Testing and Materials (ASTM):
1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by
Uniform Static Air Pressure Difference.
2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform
Static Air Pressure Difference.
3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain
Walls by Uniform Static Air Pressure Difference.
4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static
Air Pressure Differential.
5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies.
D. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
1.03 SUBMITTALS
A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and
handle height.
B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's
Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and
completion date, type and size of unit installed.
1.04 QUALITY ASSURANCE
A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufac-
turer with at least 25 years experience in providing fenestration systems in the North American market.
1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard.
2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005
standard.
B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/
WDMA/CSA 101/I.S.2/A440-0 Testing results to include air infi ltration in accordance with ASTM E 283, water
32 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330
and forced entry in accordance with ASTM F 588.
** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Compara-
tive analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading
design pressures specifi cally required for the project. Check for limitations on the use of these charts in the
jurisdiction of the project). See manufacturer's latest published data.
C. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestra-
tion products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully
completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers
of General Contractor and Owner's contact person.
1.05 WARRANTY
A. Provide manufacturer's standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two
years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer.
1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the
following:
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material
under cover, protected from weather and construction activities.
B. Condition wood components to average prevailing relative humidity before installation.
C. Do not subject wood components to extreme nor rapid changes in heat or humidity.
D. Do not use forced heat to dry out building.
E. Store fl at in dry, well ventilated area out of direct sunlight.
PART 2 – PRODUCTS
2.01 SUPPLIER
A. NANA WALL SYSTEMS, INC. - WA68
100 Meadow Creek Drive, Corte Madera, CA 94925
Toll Free: (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0312
Website: www.nanawall.com
Email: [email protected]
B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior
approval.
2.02 MATERIALS
A. Frame and Sash: From manufacturer’s standard profi les, provide frame, sash and glazing stops with dimensions
shown on drawings.
1. Provide Sash with: Standard one lite
[OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel]
[OR with simulated divided lites in pattern as shown on drawings].
2. Type of Wood: Solid, three layer, cross-grained, kiln dried with matching solid wood glazing stops. Veneered
wood not allowed.
Douglas fi r - PEFC
[OR European pine]
[OR Meranti]
[OR Western hemlock]
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 33
Guide Specifications | NanaWall® Matching Windows and Doors
[OR Spruce]
[OR European oak]
[OR Sapeli mahogany]
[OR Cherry]
[OR Beech]
[OR Maple]
[OR Laminated Bamboo]
[OR selected FSC wood]
[OR other wood as selected]
3. Wood Finish: Finishes to be water based, opened pored
Clear sanding sealer and one additional clear coat
[OR base coat and one additional clear coat]
[OR pigmented # 410 or # 510 with one additional clear coat]
SPECIFIER’S NOTE: Before installation, the unit must be fi eld fi nished with at least two coats for a fi nal
protected fi nish.
4. Aluminum Extrusion: Extrusions with nominal thickness of .078” (2.0 mm). Alloy specifi ed as AIMgSi0.5 with
strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated
conforming to AAMA 2604.
5. Aluminum Finish:
Select from NanaWall Powder Coating Finish Chart
[OR clear anodized]
[OR dark bronze anodized]
[OR select from range of RAL high gloss powder coated fi nishes available from manufacturer]
[OR select from range of RAL matte powder coated fi nishes available from manufacturer]
[OR custom fi nish].
6. Exterior aluminum extrusion to be attached to interior wood with manufacturer’s thermal isolating polyamide
connectors to protect and isolate wood from aluminum by use of the back ventilated, rain screen principle.
B. Glass:
1. Provide manufacturer’s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only,
which are fi xed with hidden nails. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC
16CFR 120
15/16” (24 mm) insulating clear safety
[OR 15/16” (24 mm) insulating argon fi lled Low-E safety]
[OR 1 ¼” (32 mm) triple glazed insulating argon fi lled Low-E safety]
[OR other glass available from manufacturer].
2. For insulated units, provide manufacturer’s standard glass spacers. Provide without capillary tubes [OR with
capillary tubes].
C. Tilt Turn Hardware
1. Provide manufacturer’s standard cam type multipoint locking mechanism.
a. The concealed multipoint locking mechanism shall be driven by a single locking handle.
2. Provide manufacturer’s standard hinges, pins, strikes, and limit stays.
34 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications3. Handles:
Stainless steel window handles in a titanium black fi nish
[OR stainless steel window handles in a brushed satin fi nish]
SPECIFIER’S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other
suppliers.
D. Provide handle height centered [OR at 41 3/8” from bottom of panel] [OR as specifi ed from bottom of panel].
E. Weather stripping: Provide manufacturer’s standard double layer EPDM
2.03 FABRICATION
A. Use solid, three layer, cross grained frame and sash profi les connected to exterior aluminum extrusion, tilt turn hardware
and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window/door.
Construction of wood panels to include close tolerance mortise and tenon, glued and pinned corners. Factory pre-assemble
as is standard for manufacturer and ship with all components and installation instructions.
B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and
double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right]
2.04 ACCESSORIES (Edit for project requirements.)
A. Provide insect screen. Mesh in gray [Or black]
Provide screen frame in aluminum:
White powder coated
[OR clear anodized]
[OR dark bronze anodized]
[OR powder coated select from range of RAL powder coated fi nishes available from manufacturer].
B. Provide other side lites, transoms as per drawings provided.
PART 3 – EXECUTION
3.01 ERECTION
A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity of the
header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no uneven-
ness, bowing, or bumps on the fl oor.
C. Installation of units constitutes acceptance of existing conditions.
3.02 INSTALLATION
A. Install frame in accordance with manufacturer’s recommendations and installation instructions. Properly fl ash and
waterproof around the perimeter of the opening.
B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level, straight,
plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work.
C. Install sash and handles in accordance with manufacturer’s recommendations and installation instructions.
D. If necessary, adjust hardware for proper operation.
E. Finishing: Field fi nish under Section 09900 -Painting; seal and fi nish promptly after installation and prior to exposure to
weather in accordance with manufacturer recommendations.
F. Accessories: Screens; install in accordance with screen manufacturer’s recommendations and installation
instructions.
END OF SECTION
DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to,
compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not intended to be
verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the particular requirements of a
specifi c construction project.
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 35
Guide Specifications | NanaWall® Matching Windows and Doors
Guide Specifications - Section 085200
NanaWall® WD68 - Wood Framed Dual Action Tilt Turn Window
PART 1 – GENERAL
1.01 SUMMARY
A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass
and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on
drawings and specifi ed herein, with NanaWall® WD68, the Wood Framed Dual Action Tilt Turn Window as supplied
by NANA WALL SYSTEMS, INC.
1.02 REFERENCES
A. American Architectural Manufacturers Association (AAMA):
1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights.
B. American National Standards Institute (ANSI):
1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Build-
ings.
C. American Society for Testing and Materials (ASTM):
1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by
Uniform Static Air Pressure Difference.
2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform
Static Air Pressure Difference.
3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain
Walls by Uniform Static Air Pressure Difference.
4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static
Air Pressure Differential.
5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies.
D. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
1.03 SUBMITTALS
A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and
handle height.
B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's
Manual with installation instructions.
C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and
completion date, type and size of unit installed.
1.04 QUALITY ASSURANCE
A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufac-
turer with at least 25 years experience in providing fenestration systems in the North American market.
1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard.
2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005
standard.
B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/
WDMA/CSA 101/I.S.2/A440-05. Testing results to include air infi ltration in accordance with ASTM E 283, water
penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330
and forced entry in accordance with ASTM F 588.
36 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis
charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures
specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project).
See manufacturer's latest published data.
C. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestra-
tion products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully
completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers
of General Contractor and Owner's contact person.
1.05 WARRANTY
A. Provide manufacturer's standard warranty against defects in materials and workmanship.
B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two
years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer.
1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the
following:
1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material
under cover, protected from weather and construction activities.
B. Condition wood components to average prevailing relative humidity before installation.
C. Do not subject wood components to extreme nor rapid changes in heat or humidity.
D. Do not use forced heat to dry out building.
E. Store fl at in dry, well ventilated area out of direct sunlight.
PART 2 – PRODUCTS
2.01 SUPPLIER
A. NANA WALL SYSTEMS, INC. - WD68
100 Meadow Creek Drive, Corte Madera, CA 94925
Toll Free: (800) 873-5673
Telephone: (415) 383-3148
Fax: (415) 383-0312
Website: www.nanawall.com
Email: [email protected]
B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior
approval.
2.02 MATERIALS
A. Frame and Sash: From manufacturer’s standard profi les, provide frame, sash and glazing stops with dimensions
shown on drawings.
1. Provide Sash with: Standard one lite
[OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel]
[OR with simulated divided lites in pattern as shown on drawings].
2. Type of Wood: Solid, three layer, cross-grained, kiln dried with matching solid wood glazing stops. Veneered
wood not allowed.
Douglas fi r - PEFC
[OR European pine]
[OR Meranti]
SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE © 2013 NanaWall Systems www.nanawall.com 37
Guide Specifications | NanaWall® Matching Windows and Doors
[OR Western hemlock]
[OR Spruce]
[OR European oak]
[OR Sapeli mahogany]
[OR selected FSC wood]
[OR other wood as selected]
3. Wood Finish: Finishes to be water based, opened pored
Clear sanding sealer for stain
[OR base coat applied for paint]
SPECIFIER’S NOTE: Before installation, the unit must be fi eld fi nished with at least two coats for a fi nal protected fi nish.
B. Glass:
1. Provide manufacturer’s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only,
which are fi xed with hidden nails. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC
16CFR 1201.
15/16” (24 mm) insulating clear safety
[OR 15/16” (24 mm) insulating argon fi lled Low-E safety]
[OR 1/4” tempered]
[OR other glass available from manufacturer].
2. For insulated units, provide manufacturer’s standard glass spacers. Provide without capillary tubes [OR with
capillary tubes].
C. Tilt Turn Hardware
1. Provide manufacturer’s standard cam type multipoint locking mechanism.
a. The concealed multipoint locking mechanism shall be driven by a single locking handle.
2. Provide manufacturer’s standard hinges, pins, strikes, and limit stays.
3. Handles:
Stainless steel window handles in a titanium black fi nish
[OR stainless steel window handles in a brushed satin fi nish]
SPECIFIER’S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other
suppliers.
D. Provide handle height centered [OR at 41 3/8” from bottom of panel] [OR as specifi ed from bottom of panel].
E. Rain Channel: Provide clear anodized rain channel
[OR dark bronze anodized rain channel]
1. Aluminum Extrusion: Extrusions with nominal thickness of .078” (2.0 mm). Alloy specifi ed as AIMgSi0.5 with
strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611.98.
F. Weather stripping: Provide manufacturer’s standard double layer EPDM
2.03 FABRICATION
A. A. Use solid, three layer, cross grained frame and sash profi les, tilt turn hardware and handles, rain channel,
glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Construction
of wood panels to include close tolerance mortise and tenon, glued and pinned corners. Factory pre-assemble as
is standard for manufacturer and ship with all components and installation instructions.
B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns
and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right]
38 © 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
NanaWall® Matching Windows and Doors | Guide Specifications
2.04 ACCESSORIES (Edit for project requirements.)
A. Provide insect screen. Mesh in gray [Or black]
Provide screen frame in aluminum:
White powder coated
[OR clear anodized]
[OR dark bronze anodized]
[OR powder coated select from range of RAL powder coated fi nishes available from manufacturer].
B. Provide other side lites, transoms as per drawings provided.
PART 3 – EXECUTION
3.01 ERECTION
A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity
of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span.
B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no
unevenness, bowing, or bumps on the fl oor.
C. Installation of units constitutes acceptance of existing conditions.
3.02 INSTALLATION
A. Install frame in accordance with manufacturer’s recommendations and installation instructions. Properly fl ash and
waterproof around the perimeter of the opening.
B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level,
straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with
other work.
C. Install sash and handles in accordance with manufacturer’s recommendations and installation instructions.
D. If necessary, adjust hardware for proper operation.
E. Finishing: Field fi nish under Section 09900 -Painting; seal and fi nish promptly after installation and prior to exposure
to weather in accordance with manufacturer recommendations.
F. Accessories: Screens; install in accordance with screen manufacturer’s recommendations and installation
instructions.
END OF SECTION
DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited
to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not
intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the par-
ticular requirements of a specifi c construction project.