mwp bucket teeth information broshure
TRANSCRIPT
MAGNUM WEAR PARTS | P: 780-978-2895
REPLACEMENT BUCKET TEETH Identifiable characteristics of the replacement bucket teeth we carry and the corresponding locking mechanism.
TOOTH STYLE PIN HOLE LOCATION
PIN HOLE SHAPE
IDENTIFICATION PICTURE
CATERPILLAR SIDE ROUND2 pc STEEL PIN &
STEEL OR SLEEVED RETAINER
RETAINER IS A LOCK WASHER RECESSED DEEP
INTO ADAPTER
ESCO CONICAL TOP RECTANGLE 2 pc STEEL PIN & RUBBER LOCK
LOCK IS INSIDE NOSE OF ADAPTER; TOOTH IS PUT ON
& PIN IS DRIVEN INTO TOP OF TOOTH
ESCO HELILOK / VERTALOK
NO PIN HOLES N/A
HELILOK: 1 pc HORE-SHOE SHAPED PIN
VERTALOK: 2 pc PIN & PLUG
“EARS” ON OUTSIDE OF PICKET INSTEAD OF PIN
HOLES
ESCO SUPER-V NO PIN HOLES N/A 1 pc PIN (TWO PIN
STYLES - PICTURED)
SQUARED “EARS” AT END OF POCKET; PIN IS INSERTED
BETWEEN THE EARS & THE NOSE OF THE ADAPTER
KOMATSU SIDE ROUND1 pc STEEL PIN WITH STEEL SNAP RING AT
CENTER OF PINLARGE ROUND HOLE
HENSLEY PARABOLIC TOP RECTANGLE
or ROUND
1 pc STEEL+RUBBER FLEX PIN or ALL
STEEL PIN
SMALLER TEETH USE A ROUND STEEL ROLL PIN (RARE HENSLEY’S USE A
SIDE PIN)
H&L SIDE OBLONG 1 pc STEEL+RUBBER FLEX PIN
SOME RARE H&L TEETH USE A TOP PIN
HYUNDAI SIDE ROUND2 pc STEEL PIN &
SLEEVED or STEEL RETAINER
RETAINER IS A LOCK WASHER RECESSED DEEP
INTO ADAPTER
COMBI SIDE OBLONG 1 pc STEEL & RUBBER FLEX PIN
POCKET IS NOTCHED. PIN LOCATED ON SIDE OF
TOOTH AT UPPER END OF POCKET
LOCKING SYSTEM
MAGNUM WEAR PARTS | P: 780-978-2895
BUCKET TOOTH PROFILES EXCAVATORS
MOST Penetrative
LEASTPenetrative
PROFILE TYPE PICTURE FEATURES & BENEFITS
TIGER
-Unmatched penetration in frost, rock or hard-pan conditions.-Stays sharp.-Little wear material = shorter lifespan.
TWIN TIGER-More penetration longer life than Tiger.-Less leverage than Tiger requiring more breakout force from the Excavator.
PENETRATION
-Good penetrating tooth.-Stays sharp throughout life.-Average wear material.-Good for lightly packed rock shale & clay.
EXTRA
-Premium design for max penetration and lifespan.-Tip has self sharpening rib.-Reinforced box for rock and abrasive terrain.
FLAT PENETRATOR(SYL)
-Good penetration & digging action in most medium to hard pack conditions.-Vertical rib on both sides maintains sharp point w/ average amount of wear material.
ROCK CHISEL-Best for use on rock or hard ground.-Remains sharp throughout life.-Good leverage takes pressure off machine. & bucket improving performance & lifespan.
ROCK ABRASION
-Similar to Rock Chisel but much more wear material on underside of tooth.-Best for use on any high abrasion application.
STANDARD LONG
-Multi-purpose general duty tooth.-Good choice for most basic applications. -Available in most styles of teeth.-Available for most sizes of equipment.
FLARE-Desinged for mud or soft ground.-Works as a paddle to lift earth. -Best for clean-out/utility work.
HEAVY DUTY LONG-Very similar to Standard Long but with much more wear material throughout.-Longest wear life of all the tooth profiles.
MAGNUM WEAR PARTS | P: 780-978-2895
BUCKET TOOTH PROFILES LOADERS
MOST Penetrative
PROFILE TYPE PICTURE FEATURES & BENEFITS
ROCK ABRASION
- Good Penetration, Wear material on underside of tooth- Best for use on any high abrasion application
HEAVY DUTY ROCK ABRASION
- Better Penetration than rock abrasion, Lots of wear material on bottom of tooth- Stays sharp- Works well in compacted & high abrasion material
STANDARD LONG
- Multi-purpose, general duty tooth- Good choice for most basic applications- Available in all styles of teeth- Available for all sizes of equipment
HEAVY DUTY LONG- Very similar to Standard Long but with much more wear material throughout- Longest wear life of all the tooth profiles
ABRASION
-Offers similar applications as the Standard Long, but with a wider tip-Extra wear panel on the bottom of the tooth-May also be found on log grapples
HEAVY DUTY
ABRASION
-Similar to Abrasion with a lot more wear material-Heavy Duty wear panels on the bottom & sides of the tooth
LEASTPenetrative
MAGNUM WEAR PARTS | P: 780-978-2895
RIPPER TOOTH PROFILES BULLDOZERS
MOST Penetrative
LEASTPenetrative
PROFILE TYPE PICTURE FEATURES & BENEFITS
HD RIPPER-Premium wear steel and ribbed faces. Allow for better material flow, tooth strength and wear material in harsh conditions.
RIPPER PENETRATION
-Designed for better ripping in hard pack. -Large rib in center allows material to flow better and gives the tooth more stability.
NON-CENTERLINE-Similar to centerline, but with more of the steel put back to allow for more stability and wear steel in usable areas.
ABRASION-Non-centerline design that has more material put into the profile.-Allows for extra wear in standard ripping conditions.
CENTERLINE-Designed for general purpose ripping conditions.-Tooth is reversible as both front and back are the same profile and have equal material on each side.
CENTERLINE SHORT
-Same as a regular centerline, but shorter to give more strength in the wear material.-Tooth is less likely to have breakages in tougher condtions.
The Profile of a tooth indicates the level of penetration it’s capapble of & therefore determines the applications that the tooth is best suited for. The following numbers will indicate the Profile of the tooth (Profile Number Cross Reference):
HOW TO IDENTIFY MOST CATERPILLAR STYLE TEETH:
The 4th & 5th digits are most important and indicate the Family that the tooth belongs to. The 6th digit may indicate the Profile of the tooth. The 7th & 8th digits may, in some cases, describe the Manufacturer or the Profile.
A Caterpillar style tooth can often be identified by its part number. Certain digits of the part number have specific meanings:
1 - Short 8 - Sharp2 - Long, HD Long, Standard 9 - Penetration3 - Abrasion, HD Abrasion 0 - Flare / Wide
Eg: Part number 1U3352RC = J350 Family, Standard Long tooth with a Rock Chisel profile
MAGNUM WEAR PARTS | P: 780-978-2895
BUCKET ADAPTER PROFILESLoaders & ExcavatorsAvailable for Caterpillar, Esco, Komatsu, Hensley, H&L, Combi, MTG, and more!
PROFILE TYPE PICTURE FEATURES & BENEFITS
FLUSHMOUNT -Used exclusively on Loaders.-Sits on top of bucket lip to allow for loader to scrape clean.
1-1/2 LONG LEG TOP
-Generally meant for Loaders (used on some Excavators).-The Loader application is good for buckets using a wear edge or lip protector between adapters.-An angled left & right hand adapter is available in some Cat Loader sizes only.-Not to be used on Cat or Komatsu Excavators
1-1/2 LONG LEG BOTTOM
-Used exclusively on Excavators -Wraps around the bucket lip with the longest leg on the bottom to provide support.-Notched left & right hand adapter is available in some Cat sizes only.
1-1/4 LONG LEG BOTTOM
-Used exclusively on Excavators & Backhoes.-Wraps around the bucket lip with the longest leg on bottom to provide support.-Available for small Caterpillar, H&L, & most Esco styles.
WELD-ON NOSE
-Cost effective option for replacing worn out noses or for use on log grapples.-Available in all Caterpillar styles, most Esco styles & select Hensley sizes.
2 LEG BOLT-ON
-Generally used only on Loaders.-Double leg, bolt on adapter is ideal for changing to clean up bucket easily & quickly.-May have 2 or 3 bolt holes.-Available in select Caterpillar & Hensley style sizes only.-Right & Left hand adapters are available for Caterpillar only.
FLUSHMOUNT BOLT-ON
-Exclusively for small Loaders.-Allows for easy change to clean up bucket by removing the adapters.-Available in select Hensley style sizes only.
MAGNUM WEAR PARTS | P: 780-978-2895
BUCKET ADAPTER PROFILES BULLDOZER
PROFILE TYPE PICTURE FEATURES & BENEFITS
WELD ON NOSE - Replaceable nose for ripper shanks.- Tooth pins directly onto nose that is welded to existing shanks.
NOSE SEGMENT- Quarter shank that is welded into the full shank- This is the primary wear section of a shank assembly that replaces worn out or broken shanks.
SHANK ASSEMBLY- Full Shank assembly that bolts onto dozers and graders.- Can be designed to fit almost any tooth system and shank guards.
SHANK GUARD HD SHARP
- Similar to a regular shank guard that has more material built up to provide extra protection and wear material. - Sharp design allows the material to flow better across the face of the shank.
OEM
SERIES
CAT ESCO H&L KOMATSU COMBI HENSLEY MTG
J SERIES
K SERIES
CON
ICAL
SUPER V
HELILO
K VERTA
LOK
ULTRA
LOK
FLEX PIN
SIDE PIN
K-MA
X
C-LOCK
PARA
BOLIC
XS
KING
MET
V13 2AF MINI 04 MG5
J200 18 V17- 17 U20 230 W8 C0 X156 05 MG8
J220 25 V19 19 240 C0 X160 10 MG10
J250 30 V23 21 U25 250 15 C1 X220 15 MG15
J300 K80 35 V29 27 U30 270 200 20 C2 X310 20 MG20
J350 K90 40 V33 U35 31 25 C3 X330 25 MG30
J400 K100 45 V39 37 U40 300 30 C3.5 X370 30 MG40
J460 K110 50 V43 47 U45 32 400 40 C4 X410 40 MG55
J550 K130 55 V51 57 U55 33 50 X450 50 MG65
J660 K150 65 V59 U60 650 70 C5 X500 50 MG80
J700 K170 70 V61 67 U70 85 X600 85 MG125
J800 V69 U80 1000 C6 115 MG200
OEM BUCKET TOOTH SERIESWe carry a complete aftermarket inventory of all the most common OEM bucket tooth series listed below:
CO
MPA
RA
TIVE O
EM TO
OTH
PRO
FILES
CATERPILLAR STYLE BUCKET TEETHPopular CAT Series. All series available.
J250 SeriesTooth PocketW: 2-1/4’’H: 2-3/4’’D: 3-1/8’’
PINS
Standard9J2258W: 9/16’’L: 3-1/8’’
8e6259OD: 1-3/16’’ID: 17/32’’
J350 SeriesTooth PocketW: 3-1/8’’H: 3-1/4’’D: 4-1/16’’
PINS LOCKS
Standard9J2358W: 3/4’’L: 4-1/4’’
8e6359OD: 1-3/4’’ID: 23/32’’
J450/460 Series
PINS LOCKS
J460Standard
1U1458W: 3/4’’L: 5-1/4’’
8e6359OD: 1-3/4’’ID: 23/32’’
Tooth PocketW: 3-15/16’’H: 4-1/4’’D: 4-7/8’’
J550 SeriesTooth PocketW: 4-7/8’’H: 4-5/8’’D: 5-3/4’’
PINS LOCKS
Standard1U1558W: 1’’L: 6-3/8’’
8e5559OD: 2’’ID: 31/32’’
MAGNUM WEAR PARTS | P: 780-978-2895
MAGNUM WEAR PARTS | P: 780-978-2895
Tooth PocketW: 2-1/2’’H: 2-1/2’’D: 3’’
STANDARD PIN
V23pN W: 5/8’’ L: 2-1/16’’
V23 Series
ESCO SUPER - V STYLE BUCKET TEETHPopular Esco Super-V Series. All series available, inclusive of Helilock, Conical, and Vertilok.
Tooth PocketW: 2-13/16’’H: 2-13/16’’D: 2-13/16’’
V29 Series
STANDARD PIN V29pN W: 7/8’’ L: 3-1/8’’
Tooth PocketW: 3-1/4’’H: 3-1/4’’D: 3-3/16’’
V33 Series
STANDARD PIN
V33pN W: 7/8’’ L: 3-3/8’’
V43 SeriesTooth PocketW: 4’’H: 4’’D: 4‘’
STANDARD PIN
V43pN W: 1-1/8’’ L: 4-1/8’’
PIN LOCKS (2 required)
390LTp IW: 17/32’’ IH: 4-3/4’’
75KLKSR W: 13/16’’ L: 3-3/16’’
Log Grapple Tooth PocketW: 7-7/8’’H: 3-1/4’’D: 3-1/2’’
ApplicationPart #
Weight / Pc
Weld On Nose 75LLWN
68.00 lbs
V51 SeriesTooth PocketW: 4-1/8’’H: 4-1/8’’D: 4-5/16‘’
STANDARD PIN
V51pN W: 1-1/2’’ L: 4-7/16’’
75LL
MAGNUM WEAR PARTS | P: 780-978-2895
Tooth PocketW: 1-1/8‘’H: 1-1/4’’D: 2-1/2‘’
2A Series
23 SeriesTooth PocketW: 1-9/16‘’H: 1-3/4’’D: 2-7/8‘’
FLEX PIN XL FLEX PIN
23p W: 23/32’’ H: 2-1/8’’
23peX W: 23/32’’ L: 2-1/2’’
4 TAB FLEX PIN
23p4T W: 23/32’’ L: 2-1/8’’
Tooth PocketW: 2-1/16‘’H: 2-3/16’’D: 3-5/8‘’
25 Series
FLEX PIN
25p W: 27/32’’ L: 2-27/32’’
Tooth PocketW: 2-1/2‘’H: 1-3/4’’D: 3-1/4‘’
SPLIT ROLL PIN
p156 W: 3/8’’ H: 2’’
X156 SeriesTooth PocketW: 2-1/2‘’H: 1-3/4’’D: 3-1/4‘’
FLEX PIN
23p W: 23/32’’ H: 2-1/8’’
X156X Series
H&L STYLE BUCKET TEETHPopular H&L Series. All series available.
HENSLEY STYLE BUCKET TEETHPopular Hensley Series. All series available.