mts/t-berd - 5800...loopback device is an alu 7705. select “traffic” for all other loopback...

MTS/T-BERD - 5800

2

Hardware Description

3

User Interface

RFC 2544

5

RFC 2544 Test Procedure

Select Test In the Select Test menu, ,at the top left corner of the screen, choose one of the following:

• For 10BASE-T, 100BASE-T, or 1000BASE-T Electrical Ethernet testing: Ethernet►10/100/1000► RFC 2544 ►L2 Traffic►P1 Terminate.• For 100BASE-FX Optical Fast Ethernet testing:Ethernet►100M Optical► RFC 2544 ►L2 Traffic►P1 Terminate.• For 1000BASE-SR, 1000BASE-LR, or other GigE Optical Testing: Ethernet►1GigE Optical►RFC 2544 ►L2 Traffic►P1 Terminate.• For 10GBASE-SR, 10GBASE-LR, other 10GigE Optical Testing: Ethernet►10GigE LAN► RFC 2544 ►L2 Traffic►P1 Terminate.

6

RFC 2544 Test Procedure - Configure

If this is the first time using the RFC2544 test and your unit does not have pre-loaded configuration files, tap the button next to “Start a New Configuration (reset to defaults)” and proceed to step 2.

Otherwise, tap the button next to “Load Configuration from a Profile”

Select the desired configuration, and tap . Tap to acknowledge successful load, tap the button, and tap the button next to Edit Configuration.

7

RFC 2544 Test Procedure - Symmetry

In the Symmetry configuration screen, verify that Throughput = Symmetric and Measurements = Loopback, then tap the button.

8

RFC 2544 Test Procedure – L2 SettingsOption Value(s) CommentFrame Type DIXEncapsulation None or VLAN See Work Order

Test Mode Traffic or LBM Traffic

Select “LBM Traffic” if the loopback device is an ALU 7705. Select “Traffic” for all other loopback devices.

VLAN ID See Work Order Option only displayed if Encapsulation = VLANUser Priority 0 (lowest)

Source Type Factory Default Tap the Set Loop Type and MAC Addresses or Set MAC Addresses and LBM links to configure these settings. (See below)

Destination MACEnter MAC address of the loopback device

Loop Type UnicastOptions only displayed if Test Mode = Traffic

EtherType 0800Auto-increment SA MAC No

Maint. Domain Level

See work order. Set to same value as ALU 7705 Options only displayed if Test

Mode = LBM TrafficEnable Sender TLV No (unchecked)

9

RFC 2544 Test Procedure – Other Settings

Use the or button at the bottom of the screen to advance through the wizard and configure the remaining settings as follows:

Screen Option Value(s) Comment

RFC 2544 Tests: Configuration Templates

Do you want to use a configuration template?

No

RFC 2544 Tests: Select Tests

RCF 2544 Tests Throughput, Latency, Frame Loss

Additional Tests Packet Jitter

10


RFC 2544 Tests: Utilization

Bandwidth Unit L1 Mbps

Maximum Bandwidth See Work Order Enter Committed Information Rate (CIR)

Frame Lengths

Select 1st, 4th, and 8th

Frame Lengths. If the MTU is greater than

1518 (1522 with VLAN), also enter and select the frame length of the MTU.

Deselect (uncheck) all other frame sizes.

RFC 2544 Tests: Throughput

Zero-in Process JDSU Enhanced

Measurement Accuracy To within 1 Mbps

11


RFC 2544 Tests: Frame Loss Test

Test Procedure RFC 2544 Standard

Bandwidth Granularity (L1Mbps)

Enter minimum value: 1 for 100Mbps

Ethernet 10 for Gigabit

Ethernet 100 for 10GigE

Test Ctls: Test Durations

Configure test durations separately? No

Duration 120 secondsThis will result in approximately 6 minutes of test time per frame length.Number of Trials 1

Test Ctls: Test Thresholds

Show Pass/Fail Select all ()

Throughput Threshold See Work Order Enter CIR

Throughput Frame Loss Tolerance (%) See Work Order Enter 0.000 if not specified

Latency RTD (µs) See Work Order

Enter threshold in µsecs (1 msec = 1000 µsec). Uncheck the Show Pass/Fail box if athreshold is not specified.

Packet Jitter (µs) See Work Order

Acterna Payload Version Version 2

12

RFC 2544 Test Procedure – Save Profile

In the Save Profiles screen, enter a Filename, and tap . Tap , tap , and tap twice.

13

RFC 2544 Test Procedure – Running the Test

Ensure that the loopback device has been setup, and tap to run J- QuickCheck to verify local connectivity, loop up the remote loopback device, and check available bandwidth.

14

RFC 2544 Test Procedure – Running the Test

Tap , and tap . The T-BERD will loop up the loopback device and run all configured tests.

Detailed results for each test can be viewed by tapping .

15

RFC 2544 Test Procedure – Create a Report

Tap twice and enter Customer name, Technician ID, Test Location, Work Order Number and Comments/Notes.

Tap again and tap

View the Report and tap

Y.1564

17

Y.1564 Test Procedure

Select Test In the Select Test menu, ,at the top left corner of the screen, choose one of the following:• For 10BASE-T, 100BASE-T, or 1000BASE-T Electrical Ethernet testing: Ethernet►10/100/1000► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.• For 100BASE-FX Optical Fast Ethernet testing:Ethernet►100M Optical► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.• For 1000BASE-SR, 1000BASE-LR, or other GigE Optical Testing: Ethernet►1GigE Optical► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.• For 10GBASE-SR, 10GBASE-LR, other 10GigE Optical Testing: Ethernet►10GigE LAN► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.

18

Y.1564 Test Procedure - Configure

If this is the first time using the Y.1564 test and your unit does not have pre-loaded configuration files, tap the button next to “Start a New Configuration (reset to defaults)” and proceed to step 2.

Otherwise, tap the button next to “Load Configuration from a Profile”

Select the desired configuration, and tap . Tap to acknowledge successful load, tap the button, and tap the button next to Edit Configuration.

19

Y.1564 Test Procedure - Setup

Use the and buttons at the bottom of the screen to advance through the wizard and configure Layer 2 Network Setting as follows:

Screen Option Value(s) Comment

Connect: SymmetryThroughput Symmetric

Measurements Loopback

Connect: Configuration Templates

Do you want to use a configuration template? No

Connect: Local Settings Frame Type DIX

Network Services

Number of Services See Work Order Enter 1 if not specified.

Test Mode Traffic or LBM Traffic

Select “LBM Traffic” if the loopback device is an ALU 7705. Select “Traffic” for all other loopback devices.

20


Network: Services, LBM Settings (Advanced)

Maint. Domain Level See Work OrderTap the LBM settings link to configure these settings.Enable Sender TLV No (unchecked)

Network: Services, Network Settings (Advanced)

Frame Size See Work Order; Enter EMIX if not specified

Tap the DA MAC and Frame Size settings link to configure these settings.Dest. MAC Address See Work Order

Network: Tagging

Do Services have different VLAN ID’s or User Priorities? See Work Order Select No if not specified

Encapsulation See Work Order None or VLAN.Select None if not specified

VLAN ID See Work Order

User Priority See Work Order

SLA: SLA Throughput

Enable Aggregate Mode No (unchecked)

CIR See Work Order

EIR See Work Order Enter 0 if not specified

Policing

Select if CIR < line rate.

Deselect if CIR = line rate

21


SLA:SLA Burst

Would you like to perform burst testing? See Work Order Select No if not specified

Burst Test Type Committed Burst SizeCBS See Work Order

SLA: SLA Performance

Frame Loss Ratio See Work Order Enter 0.000000 if not specified.

Frame Delay (RTD, ms) See Work Order

If not specified: 50 for Circuit Emulation 20 for EPL/EVPL 10 for Mobile Backhaul

Delay Variation (ms) See Work Order

If not specified: 20 for Circuit Emulation 20 for EPL/EVPL 2 for Mobile Backhaul

Acterna Payload VersionSelect “Version 3” if loopback device is another T-BERD.Otherwise, select “Version 2”

Test ControlsNumber of Steps Below CIR 3

Step Duration (Sec) 15Test Duration 5

22

Y.1564 Test Procedure – Save Profile

In the Save Profiles screen, enter a Filename, and tap . Tap , tap , and tap twice.

23

Y.1564 Test Procedure – Running the Test

In the Select Y.1564 Tests screen, select all Services, Service Configuration Test, Service Performance Test, and Throughput (RFC-2544). Enter the total (Sum) CIR for all combined services in the Max. (L1 Mbps) field, then press

24


Ensure that the loopback device has been setup, and tap to run J-QuickCheck to verify local connectivity, loop up the remote loopback device, and check available bandwidth.

25


Tap , and tap . The T-BERD will run all configured tests.

Detailed results for each test can be viewed by tapping .

26

Y.1564 Test Procedure – Create a Report

Tap twice and enter Customer name, Technician ID, Test Location, Work Order Number and Comments/Notes.

Tap again and tap

View the Report and tap

Software Update

28

Software update

Power On - Press and hold the ON/OFF button to turn on the T-BERD 5800v2. AC Power - Connect the AC power

adapter to the power connector on the side of the T-BERD 5800v2. LAN Connection - Connect the

Ethernet Management Port on the side of T-BERD 5800v2 to a network connection with internet access, using CAT 5E or better cable.

29

Software update – Network Upgrade

Press the System icon, , at the top of the start-up screen, to display the System Menu.

30


Press the Network icon, , to display LAN Settings. Set IP Mode to “DHCP” for automatic IP address assignment or “Static” for manual input.

After configuring LAN settings, press the System icon, , to redisplay the System Menu.

31


Press the Upgrade icon, , to display upgrade methods.

32


Press to display upgrade settings. Ensure that Server Address = “5800v2.updatemyunit.net”

33


Press to show the upgrade versions available at upgrademyunit.net.

Press , and press to initiate the upgrade.

34

Software update – USB Upgrade

Using an internet browser on your PC or laptop, go to http://updatemyunit.net/

35


Click on to display the T-BERD 5800v2 upgrade portal.

Download the file by clicking one of the flags and save extract the files in a USB

36


Press the Upgrade icon, , to display upgrade methods.

37


Press to show the upgrade versions available at upgrademyunit.net.

Press , and press to initiate the upgrade.

mts/t-berd - 5800...loopback device is an alu 7705. select “traffic” for all other loopback...

Documents