mps-camx3sp1 installation installation...

2
IMPORTANT 1. This product fit 2017-2020 CAN-AM X3 2. Please read the installation instructions carefully before you start. 3. If the vehicle is clean and free of other debris, it will be easy to install. 4. For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below PRODUCT INFORMATION: BEFORE YOU BEGIN 1..Read these instructions and check to be sure all parts and tools are accounted for. 2. Please retain these installation instructions for future reference and parts ordering information Step 1: Remove the two screws (A) and 3 Torx (B) from the original X3 door. Step 2: Assemble Speed nut (3) and the plastic mount (10) according to the direction shown in picture 2. INSTALLATION TIPS: 01 02 03 04 05 06 07 08 09 10 11 x1 x1 x6 x6 x6 x2 x8 x6 x6 x6 x2 Door Speaker Pod R Door Speaker Pod L Speed nut M4 Allen screw M4x12 Flat washer M4 Allen button head M6X25 Flat washer M6 Allen Bolt M6X45 Nylock Nut M6 Plastic mount Pan head screw 4x16 01 02 03 03 04 05 06 07 08 09 10 10 11 A 1 2 MPS-CAMX3SP1 INSTALLATION INSTRUCTIONS #MetraPowerSports B

Upload: others

Post on 02-Mar-2021

11 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: MPS-CAMX3SP1 Installation INSTALLATION ...metraonline.com/files/products/MPS-CAMX3SP1_instructions.pdfMPS-CAMX3SP1 INSTALLATION INSTRUCTIONS #MetraPowerSports B Step 3: Assemble the

Installation

IMPORTANT1. This product fit 2017-2020 CAN-AM X3 2. Please read the installation instructions carefully before you start. 3. If the vehicle is clean and free of other debris, it will be easy to install. 4. For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below

PRODUCT INFORMATION:

BEFORE YOU BEGIN1..Read these instructions and check to be sure all parts and tools are accounted for. 2. Please retain these installation instructions for future reference and parts ordering information

Step 1: Remove the two screws (A) and 3 Torx (B) from the original X3 door.

Step 2: Assemble Speed nut (3) and the plastic mount (10) according to the direction shown in picture 2.

INSTALLATION TIPS:

0102030405060708091011

x1x1x6x6x6x2x8x6x6x6x2

Door Speaker Pod RDoor Speaker Pod LSpeed nut M4Allen screw M4x12Flat washer M4Allen button head M6X25Flat washer M6Allen Bolt M6X45Nylock Nut M6Plastic mountPan head screw 4x16

01

02

03

03

04

05

06

07

08

09

10

10

11

A

1

2

MPS-CAMX3SP1INSTALLATION INSTRUCTIONS#MetraPowerSports

B

Page 2: MPS-CAMX3SP1 Installation INSTALLATION ...metraonline.com/files/products/MPS-CAMX3SP1_instructions.pdfMPS-CAMX3SP1 INSTALLATION INSTRUCTIONS #MetraPowerSports B Step 3: Assemble the

Step 3: Assemble the components from step 2 on the bottom half-door frame, picture 3. The plastic mounts will mount in the same location as the bolts remove in step 1 (B). Use the Allen M6x45 bolt (8), Flat washer (7), and Nylock nut (9) to attached the plastic clips (10) to the door frame.

Step 4: With the panel face down on a soft surface install your aftermarket speaker. Make sure the mounting hardware from your aftermarket speaker will not puncture through the front panel. If you have a tweeter a bracket may need to be created.

Step 5: Run speaker wiring to your source unit.

Step 6: Remove red backing from the double-sided tape and secure to the doors frame. Using the hardware shown attach the MPS-CAMX3SP1 to the door. Note that the original screws from step one will be used.

08

04

11

0506 07

07

09

A

3

6

©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION Rev Date 6/24/2020

Having di�culties? We’re here to help.Contact our Tech Support line at: 386-257-1187 Or via email at: [email protected] Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PMMetraPowerSports.com