UNEXCAVATED

UNEXCAVATED

UNEXCAVATED

EXISTING TUNNEL

UNEXCAVATED

UNEXCAVATED

UNEXCAVATED

1 1/2" DR UP

EXIST. DRAIN

EXIST. 3/4" DTS & DTR

EXIST EF-3

EXIST E-6"Ø

FLOOR DRAIN.SPILL OVER 1 1/2" DR

EXIST E-8x4

EXIST 1 1/2" DTS & DTR

EXIST. 4" CHWS&R AND 3" HWS&R

THRUST BLOCK

TO ALUMNI HALL

EXIST 4" CHWREXIST 4" CHWS

EXIST 3" HWSEXIST 3" HWR

EXIST UH-1

EXIST 3" DTR UP

EXIST 3" DTS UP

NEW 2" DTR

NEW 2" DTS

EXIST 3" DTR UPEXIST 3" DTS UP

3" DTR4" DTR

4" DTS

EXIST 1 1/2" DR UP

2" DTS UP

2" DTR UP

DTP-3 DTP-4

EXP-2

CONTRACTOR SHALL REMOVE SECTIONS OFEXISTING PIPING IN THIS AREA TO ALLOWACCESS FOR INSTALLATION OF NEW DTR & DTSPIPING. REMOVED PIPING SHALL BEREINSTALLED AND INSULATED TO MATCHEXISTING. ALL SHUT DOWNS SHALL BESCHEDULED WITH THE UNIVERSITY PRIOR TOANY WORK PERFORMED.

EXISTING PUMPS

EXISTING

EXPANSION TANK

REFER TO DETAIL

SHEET M2.0

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

BASEMENT PIPING PLAN

SCALE: 1/8" = 1'-0"

N

MP1.B

MECHANICAL

PIPING

BASEMENT PLAN

GENERAL NOTES:

DRAWING NOTES:

A. UNLESS OTHERWISE NOTED, ALL PIPING SHOWN IS NEW. REMOVE ALL EXISTING PIPING NOT USED IN FINAL ARRANGEMENT.JOB SITE VISIT IS REQUIRED FOR THIS DETERMINATION.

B. PIPING CONTRACTOR SHALL CAREFULLY COORDINATE PIPING LOCATIONS WITH ALL OTHER TRADES BEFORE FABRICATINGPIPING. ALL PIPING SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE. REFER TO THE SPECIFICATIONS FORCOORDINATION.

03/09/2017

03/09/2017

1-11

1-12

1-10

FCU 1-9

1-8

FCU 1-14

1-5

1-2

1-3

FCU 1-1

1" DTS

FCU 1-4

DTR

DTS

DRDTRDTS

DR

DR

C.O.

C.O.

C.O.

C.O.

C.O.

C.O.

C.O.

C.O.

DTR

ACCU-2

C.O.

#1

C C

#4 SR A24

SR

CC

S

S

SS

S

S

S

R

R

R

R

R

R

R

#3

C C

#2 #2

#10

SR

NEW 1" DR UP

NEW WORK IN THIS AREA

NEW WORK IN THIS AREA

SEE ENLARGED PLAN THIS SHEETFOR NEW WORK

EXISTING FCU FED FROMABOVE TO REMAIN.

NEW PIPE TO BE INSTALLEDIN EXISTING CHASE. REFERTO ARCHITECTURAL PLANS.

115

116

103

101

105

106

107114

113

109

112 111

110

117

104

118

120

120A

119

122

122A

121

127

128A 128

127A

125124

123

126

108

114A

109A

S

R

EXIST 2 1/2" DTR DN

EXIST 2 1/2" DTS DNEXIST 2" DTR UP

EXIST 2" DTS UP

NEW 2" DTR DN

NEW 2" DTS DN

NEW 2" BALL VALVE(TYP.)

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

FIRST FLOOR PIPING PLAN

SCALE: 1/8" = 1'-0"

N

MECHANICAL

PIPING

FIRST FLOOR PLAN

MP1.1

GENERAL NOTES:

DRAWING NOTES:

A. UNLESS OTHERWISE NOTED, ALL PIPING SHOWN IS NEW. REMOVE ALL EXISTING PIPING NOT USED IN FINAL ARRANGEMENT.JOB SITE VISIT IS REQUIRED FOR THIS DETERMINATION.

B. PIPING CONTRACTOR SHALL CAREFULLY COORDINATE PIPING LOCATIONS WITH ALL OTHER TRADES BEFORE FABRICATINGPIPING. ALL PIPING SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE. REFER TO THE SPECIFICATIONS FORCOORDINATION.

FIRST FLOOR PIPING ENLARGED PLAN

SCALE: 1/2" = 1'-0"

N

03/09/2017

03/09/2017

2-11

2-10B 2-10A

2-9

2-8

2-2

2-4

3/4" 1"

1 1/4"

1 1/2"

1 1/2"

DTS1 1/2"

DTS

DTR

2"

2 1/2"

1 1/4"

1 1/2"

1 1/2"

2 1/2"

2 1/2"

1"

1 1/4"

2"

1 1/2"

1"1 1/2"

1"

1"

DTS DTR

DTS

DTS

DTR

1 1/2" DTS & R

1 1/2" DRUP & DN.

1"

UP1 1/2" DR

3/4"

2-7

2-11

2-10B 2-10A

2-9

2-8

3" DTR DN2" DTR UP &

2" DTS UP &3" DTS DN

C.O.

C.O.

C.O.

C.O.

DTR

DTS

DTS

DTR

DTS DTR

DTR DTS

DTR

DTS

DR

C.O.

UP & DN.1 1/2" DR

2 1/2"

1"

C.O.

1 1/4"

3/4"

2 1/2"1 1/4"

1"

1"

1 1/2"

1 1/2"

2 1/2"

2"

2-1

3" DIESEL EXH. UP

2-5

3/4"

DN.1 1/2" DR

THRU ROOF

1 1 1

2-6C 2-6B 2-6A

P.O.R.P.O.R.

2

2

2

2

2

2

2

222

NEW WORK IN THIS AREA

NEW WORK IN THIS AREA

206

208

216

207

223

219

222

220

220B

218

221

220C

204A

209

210

214

205

201

202

212

217

204

211

213

213A

205A

203

218A

217A

215

212A

219

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

SECOND FLOOR PIPING DEMO PLAN

SCALE: 1/8" = 1'-0"

N

MPD1.2

MECHANICAL PIPING

SECOND FLOOR DEMO

PLAN

GENERAL NOTES:

DRAWING NOTES:

1. CONTRACTOR TO REMOVE EXISTING BRANCH PIPING TO FCU'S 6A, 6B, AND 6C AND CAP EXISTING SUPPLY, RETURN, AND DRAIN PIPINGAT P.O.R. INDICATED.

2. CONTRACTOR TO REMOVE EXISTING FAN COIL UNITS. REFER TO SHEET MP1.2 FOR DETAILED WORK IN THIS AREA.

A. UNLESS OTHERWISE NOTED, ALL PIPING SHOWN IS NEW. REMOVE ALL EXISTING PIPING NOT USED IN FINAL ARRANGEMENT.JOB SITE VISIT IS REQUIRED FOR THIS DETERMINATION.

B. PIPING CONTRACTOR SHALL CAREFULLY COORDINATE PIPING LOCATIONS WITH ALL OTHER TRADES BEFORE FABRICATINGPIPING. ALL PIPING SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE. REFER TO THE SPECIFICATIONS FORCOORDINATION.

03/09/2017

03/09/2017

2-11

2-10B 2-10A

2-9

2-8

R8L-200

S8L4-280

S8L4-235 R8L-155

R8L-155

2-6C 2-6B 2-6AS8L4-185

S8L4-185R8L-155

S8L4-235

R8L-155V12L

R-14X12

S-14X12

O.A.-6X6 O.A.-10X8

2-4

COIL

DUAL TEMPERATURECOIL FOR ACU-1

2-6C 2-6A2-6B

2-7

2-11

2-10B 2-10A

2-9

2-8

2-1

2-5

2-6B 2-6AP.O.R.

1

NEW WORK IN THIS AREA

P.O.R.

206

208

216

207

223

219

222

220

220B

218

221

220C

204A

209

210

214

205

201

202

212

217

204

211

213

213A

205A

203

218A

217A

215

212A

219

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

SECOND FLOOR SHEET METAL DEMO PLAN

SCALE: 1/8" = 1'-0"

N

MSD1.2

HVAC

SHEET METAL

SECOND FLOOR DEMO

PLAN

GENERAL NOTES:

DRAWING NOTES:

A. VERIFY CONDITIONS IN THE FIELD PRIOR TO BID AND CONSTRUCTION EFFORTS.

B. COORDINATE ALL NEW HVAC WORK WITH WORK BY OTHER TRADES PRIOR TO BEGINNING CONSTRUCTION. NO WORK IS TO BEINSTALLED OR FABRICATED UNTIL AFTER THE PROJECT COORDINATION HAS BEEN APPROVED BY THE OWNER'SREPRESENTATIVE.

C. ALL OVERHEAD DUCTWORK SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE.

D. THE HVAC CONTRACTOR SHALL PROVIDE ALL ADDITIONAL STEEL FRAMING AS REQUIRED TO INSTALL EQUIPMENT ANDDUCTWORK.

E. THE HVAC CONTRACTOR SHALL COORDINATE ALL REQUIRED WALL OPENINGS FOR DUCTWORK WITH THE GENERALCONTRACTOR PRIOR TO CONSTRUCTION OF THE NEW WALLS. ALL ADDITIONAL OPENINGS FOR DUCT PENETRATIONS SHALL BEPROVIDED BY THE HVAC CONTRACTOR IN COMPLIANCE WITH ALL CONDITIONS OF THE PROJECT SPECIFICATIONS.

F. THE HVAC CONTRACTOR SHALL PROVIDE ALL REQUIRED WALL AND FLOOR OPENINGS FOR PIPING. HVAC CONTRACTOR SHALLFIRESTOP ALL RATED OPENINGS. THE HVAC CONTRACTOR SHALL PROVIDE ALL CUTTING AND PATCHING THAT IS REQUIREDFOR PIPING PENETRATIONS THROUGH WALLS AND FLOORS.

1. CONTRACTOR TO REMOVE ALL EXISTING DUCTWORK IN THIS ROOM UP TO P.O.R. INDICATED. CONTRACTOR TO REMOVE ALL FCU'S,DIFFUSERS, AND ASSOCIATED SHEET METAL WORK IN THIS AREA.

03/09/2017

03/09/2017

2-11

2-10B 2-10A

2-9

2-8

2-2

2-4

3/4" 1"

1 1/4"

1 1/2"

1 1/2"

DTS1 1/2"

DTS

DTR

2"

2 1/2"

1 1/4"

1 1/2"

1 1/2"

2 1/2"

2 1/2"

1"

1 1/4"

2"

1 1/2"

1"1 1/2"

1"

1"

DTS DTR

DTS

DTS

DTR

1 1/2" DTS & R

1 1/2" DRUP & DN.

1"

UP1 1/2" DR

3/4"

2-7

2-11

2-10B 2-10A

2-9

2-8

3" DTR DN2" DTR UP &

2" DTS UP &3" DTS DN

C.O.

C.O.

C.O.

C.O.

DTR

DTS

DTS

DTR

DTS DTR

DTR DTS

DTR

DTS

DR

C.O.

UP & DN.1 1/2" DR

2 1/2"

1"

C.O.

1 1/4"

3/4"

2 1/2"1 1/4"

1"

1"

1 1/2"

1 1/2"

2 1/2"

2"

2-1

3" DIESEL EXH. UP

2-5

3/4"

DN.1 1/2" DR

THRU ROOF

2-12A

2-12B 2-12C

2-12D

2-12E

2-12F

2-12G

2-12H

2-12I

2-12J

NEW FAN COIL UNITS

NEW FAN COIL UNITS

NEW FAN COIL UNITS

NEW FAN COIL UNITS

1

1

111

1

1

1

1

1

EXIST 2" DTR DN

EXIST 2" DTS DN

EXIST 1 1/2" DTS

EXIST 1 1/2" DTREXIST 1 1/2" DRAIN

EXIST 1 1/2" DTS

EXIST 1 1/2" DTREXIST 1 1/2" DRAIN

EXIST DTS AND DTR DNTO 1ST FLOOR TO FEEDEXISTING FCU 1-13 TOREMAIN

2 2 2

2

2

2

2

2

2

2

NEW BALL VALVECAPPED (TYP)

2-6

1-1/8" DTS1-1/8" DTR

3/4" DR1" DR DN

NEW WORK IN THIS AREA

NEW WORK IN THIS AREA

NEW DX COIL AC-2-6

3/4" DR

3

206

208

216

207

223

219

222

220

220B

218

221

220C

204A

209

210

214

205

201

202

212

217

204

211

213

213A

205A

203

218A

217A

215

212A

219

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

SECOND FLOOR PIPING PLAN

SCALE: 1/8" = 1'-0"

N

MP1.2

MECHANICAL

PIPING

SECOND FLOOR PLAN

GENERAL NOTES:

DRAWING NOTES:

A. UNLESS OTHERWISE NOTED, ALL PIPING SHOWN IS NEW. REMOVE ALL EXISTING PIPING NOT USED IN FINAL ARRANGEMENT.JOB SITE VISIT IS REQUIRED FOR THIS DETERMINATION.

B. PIPING CONTRACTOR SHALL CAREFULLY COORDINATE PIPING LOCATIONS WITH ALL OTHER TRADES BEFORE FABRICATINGPIPING. ALL PIPING SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE. REFER TO THE SPECIFICATIONS FORCOORDINATION.

1. CONTRACTOR TO CAREFULLY REMOVE EXISTING FAN COIL UNIT LOCATED BEHIND DECORATIVE WOOD CABINETRY. CONTRACTOR SHALLREMOVE PORTION OF CABINETRY TO ALLOW REMOVAL OF EXISTING UNITS AND INSTALLATION OF NEW UNITS. CONTRACTOR SHALLREINSTALL CABINETRY.

2. CONTRACTOR TO EXTEND EXISTING DTS, DTR, AND DRAIN PIPING TO NEW FAN COIL UNITS AND MAKE CONNECTION THERETO.

3. EXISTING VENTILATION IN THIS ROOM TO REMAIN UNCHANGED.

03/09/2017

03/09/2017

2-11

2-10B 2-10A

2-9

2-8

2-6 T

O.A.-10X10

2-4

2-3

2-7

2-11

2-10B 2-10A

2-9

2-8

2-1

2-5

P.O.C.

S10L4-280 R8L-200

V12L4-400

S-10X12 S-20X12

R-10X10 R-20X10P.O.C.

V-12X10

S-12X20 DNBELOW CEILING

R-10X20 DNBELOW CEILING

SEE ENLARGED PLAN THIS SHEETFOR NEW WORK BELOW CEILINGNEW WORK IN THIS AREA

S10L4-280 S10L4-280

S10L4-280S10L4-280

R8L-200

R8L-200R8L-200 R8L-200

1

1

206

208

216

207

223

219

222

220

220B

218

221

220C

204A

209

210

214

205

201

202

212

217

204

211

213

213A

205A

203

218A

217A

215

212A

219

2-6

NEW FCU INSTALLEDBELOW CEILING. NEWFCU TO BE SUPPORTEDON UNISTRUTATTACHED TOSTRUCTURE ABOVEACT CEILING.

S-12X20 UP

R-10X20 UP

NEW DX COIL AC-2-6210

205

204

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

SECOND FLOOR SHEET METAL PLAN

SCALE: 1/8" = 1'-0"

N

MS1.2

HVAC

SHEET METAL

SECOND FLOOR PLAN

SECOND FLOOR SHEET METAL ENLARGED PLAN

SCALE: 1/4" = 1'-0"

N

GENERAL NOTES:

DRAWING NOTES:

A. VERIFY CONDITIONS IN THE FIELD PRIOR TO BID AND CONSTRUCTION EFFORTS.

B. COORDINATE ALL NEW HVAC WORK WITH WORK BY OTHER TRADES PRIOR TO BEGINNING CONSTRUCTION. NO WORK IS TO BEINSTALLED OR FABRICATED UNTIL AFTER THE PROJECT COORDINATION HAS BEEN APPROVED BY THE OWNER'SREPRESENTATIVE.

C. ALL OVERHEAD DUCTWORK SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE.

D. THE HVAC CONTRACTOR SHALL PROVIDE ALL ADDITIONAL STEEL FRAMING AS REQUIRED TO INSTALL EQUIPMENT ANDDUCTWORK.

E. THE HVAC CONTRACTOR SHALL COORDINATE ALL REQUIRED WALL OPENINGS FOR DUCTWORK WITH THE GENERALCONTRACTOR PRIOR TO CONSTRUCTION OF THE NEW WALLS. ALL ADDITIONAL OPENINGS FOR DUCT PENETRATIONS SHALL BEPROVIDED BY THE HVAC CONTRACTOR IN COMPLIANCE WITH ALL CONDITIONS OF THE PROJECT SPECIFICATIONS.

F. THE HVAC CONTRACTOR SHALL PROVIDE ALL REQUIRED WALL AND FLOOR OPENINGS FOR PIPING. HVAC CONTRACTOR SHALLFIRESTOP ALL RATED OPENINGS. THE HVAC CONTRACTOR SHALL PROVIDE ALL CUTTING AND PATCHING THAT IS REQUIREDFOR PIPING PENETRATIONS THROUGH WALLS AND FLOORS.

1. EXISTING VENTILATION IN THIS ROOM TO REMAIN UNCHANGED.

03/09/2017

03/09/2017

EXIST 24X36 CONN. TO O.A. LOUVER

EXH. LOUVEREXIST 24X36 CONN. TO

EXIST S-22X18 DN.

EXIST R-22X18 DN.

MUA-1

EXIST O.A.-24X14 DN.EXIST E-14X24 DN.

ACU-1

EXIST O.A.-24X30

EXIST O.A.-24X30

EXIST O.A.-±14X29

EXIST E-24X30EXIST E-±16X14

EXIST R-±16X28EXIST S-±13X14

EXIST E-±15X16EXIST O.A.-14X20

EXIST O.A.-±12X14

EXIST E-±45X20O.A.-±40X22

EXIST 24X36 CONN. TOEXH. LOUVER

EXIST R-22X18

EXIST E-14X24

EXIST E-20X20

E-24X30

EXIST 24X36 CONN. TO O.A. LOUVER

EXIST ACCU

NEW ACCU-2-6

ROOF BELOW

NEW BBD

NEW 36X24 EXHAUST LOUVERABOVE EXISTING EXH. FAN

E-20X20

SEAL AND MAKE WATERTIGHT.NEW EF-1 REFER TOM2.1 FOR DETAIL

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

ROOF SHEET METAL PLAN

SCALE: 1/8" = 1'-0"

N

MS1.R

HVAC

SHEET METAL

ROOF PLAN

GENERAL NOTES:

DRAWING NOTES:

A. VERIFY CONDITIONS IN THE FIELD PRIOR TO BID AND CONSTRUCTION EFFORTS.

B. COORDINATE ALL NEW HVAC WORK WITH WORK BY OTHER TRADES PRIOR TO BEGINNING CONSTRUCTION. NO WORK IS TO BEINSTALLED OR FABRICATED UNTIL AFTER THE PROJECT COORDINATION HAS BEEN APPROVED BY THE OWNER'SREPRESENTATIVE.

C. ALL OVERHEAD DUCTWORK SHALL BE INSTALLED AS TIGHT TO THE STRUCTURE AS POSSIBLE.

D. THE HVAC CONTRACTOR SHALL PROVIDE ALL ADDITIONAL STEEL FRAMING AS REQUIRED TO INSTALL EQUIPMENT ANDDUCTWORK.

E. THE HVAC CONTRACTOR SHALL COORDINATE ALL REQUIRED WALL OPENINGS FOR DUCTWORK WITH THE GENERALCONTRACTOR PRIOR TO CONSTRUCTION OF THE NEW WALLS. ALL ADDITIONAL OPENINGS FOR DUCT PENETRATIONS SHALL BEPROVIDED BY THE HVAC CONTRACTOR IN COMPLIANCE WITH ALL CONDITIONS OF THE PROJECT SPECIFICATIONS.

F. THE HVAC CONTRACTOR SHALL PROVIDE ALL REQUIRED WALL AND FLOOR OPENINGS FOR PIPING. HVAC CONTRACTOR SHALLFIRESTOP ALL RATED OPENINGS. THE HVAC CONTRACTOR SHALL PROVIDE ALL CUTTING AND PATCHING THAT IS REQUIREDFOR PIPING PENETRATIONS THROUGH WALLS AND FLOORS.

03/09/2017

03/09/2017

NOTE:

PROVIDE REMOTE OPERATOR FOR MANUAL DAMPER WHENDAMPER IS NOT ACCESSIBLE THROUGH FINISHED CEILING.

SCALE: NOT TO SCALE

DETAIL - OUTLET CONNECTION

MAIN DUCT

TAP FROM BOTTOM OF DUCT

BELLMOUTH FITTING

(MAXIMUM 6'-0",FLEX DUCT

MAIN DUCT

MANUAL DAMPER

BELLMOUTH FITTING

TAP FROM SIDE OF DUCT

MANUAL DAMPER

LONG RADIUSSHEET METAL

MINIMUM 1'-0")

(MAXIMUM 6'-0",FLEX DUCT

MINIMUM 1'-0")

ELBOW

CEILING TEEOR FRAMEFOR GYP.CLG.

CEILING TEEOR FRAMEFOR GYP.CLG.

DETAIL - FAN COIL PIPING

NOT TO SCALE

RETURN AIR

CONDENSATE DRAIN, ROUTE TONEAREST APPROVED RECEPTOR, TYP.

SUPPLY DUCT

30 DEGREES MAXIMUM.

FLEXIBLE CONNECTION

SUPPORT UNIT IN ACCORDANCE W/ MFG. RECOMMENDATIONS.

FANCOIL

(TYP.)

DUAL TEMPERATURE WATER PIPING

NOT TO SCALE

FAN COIL UNIT PIPING DIAGRAM

AIR

BALANCING VALVE

NO FLOW

STRAINER WITH

HOSE FITTING CAPPED3/4" BALL DR. VA. W/

HOSE FITTING CAPPED (TYP.)

TRV (2-WAY)

C

AIR VENT

FAN COIL UNIT

DTS MAIN

DTR MAIN

BALL VALVE (TYP.)

NOTES:REFER TO FAN COIL UNITAND VENTILATION SCHEDULE,SHEET M-5.3 FOR TRV ANDLINE SIZES TO COILS.

S-20X10 FCU R-20X10

R-±28X13S-±28X13

FLEX. CONN.

FAN COIL UNIT TYPICAL DUCTWORK CONNECTION DETAILNOT TO SCALE

SET MANUAL DAMPER TODELIVER THE QUANTITYOF O.A. AS INDICATED ONTHE FAN COIL UNIT ANDVENTILATION SCHEDULE,SHEET M-4.0.

O.A. - 10X10

TO FAN COIL UNITS.

2" DTR

2" DTS

2" DTR

2" DTS

4" HIGH CONC. PAD. INITIAL

DUAL TEMPERATURE WATER PUMP #4 (STANDBY)DUAL TEMPERATURE WATER PUMP #3(INSTALLED SIMILAR TO #4)

CHARGE SETTING 20 PSI.

DUAL TEMPERATURE PIPING DIAGRAMNOT TO SCALE

2" BALL VALVE

2" CHECK VA.

VA. W/ HOSE FITTING3/4" BALL DR.

CAPPED (TYP.)

2" STEEL

2" DTS

MANUAL AIR VENTS

EXPANSION LINE

1" BALL VA.

EXPANSION TANK MTD. ON23 GAL.(ACCEPTANCE VOL.)

(SET AT 40 PSI)PRESSURE RELIEF VA.

AUTOMATIC AIR VENT

STEEL

4" AUTO B.F. VALVE

CHECK VA.

B.F. VALVE

4" AUTO B.F. VALVE

B.F. VALVE

3/4" MCW

2 AUTO B.F. VA.

3" CAMPUS HOTWATER RETURN

4" CAMPUS CHILLEDWATER RETURN

3" CAMPUS HOTWATER SUPPLY

SUPPLYCHILLED WATER4" CAMPUS

NOTE:TEMPERATURE SENSOR IN CHILLED WATER RETURN PIPE SHALL CAUSE 2" AUTO B.F. VALVE TO CLOSE IF WATER TEMPERATURE IS HOT.

(FOR MIXING)

TEMPERATURE SENSOR(EMERGENCY SHUT-OFF)

TEMPERATURE SENSOR(HOT WATER MIXING)

TEMPERATURE SENSOR(CHILLED WATER MIXING)

3" AUTO B.F. VALVE

3" AUTO B.F. VALVE

4" DTS&RTO ALUMNI HALL

2" DTS2" DTS

BUTTERFLY VALVE (TYP.)

PRESSURE GAUGE(0-100 PSI) P/T TEST PLUG

STRAINERPUMP

NOT TO SCALE

INLINE HOT WATER PUMP DETAIL

ACC RISE IN DUCTWORK

REFER TO SPECIFIC NOTE 2

FLEXIBLE DUCTWORK

S-SUPPLY

ZONE NUMBER

NECK SIZE-6"; 8"; 10"; 12"; 14"; 15" (ROUND NECK)

FAN COIL UNIT (SEE SCHEDULE SHEET M4.0)

1-ONE WAY; 2-TWO WAY; 3-THREE WAY; 4-FOUR WAY;

L-ACOUSTICAL CEILING; D-DRYWALL CEILING 5-TWO WAY CORNER

RECTANGULAR DUCT TO ROUND DUCT TRANSITION

CEILING SUPPLY OUTLET (24"x24" DIFFUSER)

ELECTRONIC ROOM TEMPERATURE SENSOR WITH ZONE INDICATED

MANUAL VOLUME DAMPER

X INDICATES 12"x12" DIFFUSER; FD INDICATES FIRE DAMPER

SUPPLY, RETURN, EXHAUST, VENT GRILLE

EXHAUST AIR (RECTANGULAR DUCT)

RETURN AIR (RECTANGULAR DUCT)

SUPPLY AIR (ROUND DUCT)

VENTILATION TRANSFER AIR (RECTANGULAR DUCT)

CALIBRATED BALANCING VALVE

2-32

CFM

SG, RG, EG, VG

S10L4-200X

3-1T

V-24X12

R-12X8

SL

E-14X10

SOUNDLINING

S-12Ø

REDUCER

BALL VALVE

BUTTERFLY VALVE

TEMPERATURE REGULATING VALVE

CONNECT NEW DUCTWORK OR PIPING TO EXISTING AT THIS LOCATION

EXISTING DUCTWORK OR PIPING TO BE REMOVED

NEW DUCTWORK OR PIPING

EXISTING DUCTWORK OR PIPING TO REMAIN

CHILLED WATER SUPPLY

CHILLED WATER RETURN

MECHANICAL CITY WATER PIPING

HOT WATER RETURN PIPING

HOT WATER SUPPLY PIPING

MCW

GATE VALVE

HWR

HWS

CHWS

CHWR

LEGEND

OUTDOOR AIR (RECTANGULAR DUCT)OA-24X12

DR DRAIN PIPING

1" CL.3"

12" X 31

2" DEEP DRILLED HOLE. FILL WITHEPOXY & INSERT #3 BENT DOWEL.

EXISTING SLAB

#3 AT 12" C/C E.W.1" CHAMFER #3 DOWEL

CONCRETE PAD31

2"

NOT TO SCALE

TYPICAL HOUSEKEEPING PAD

NOT TO SCALE

FAN COIL UNIT 2-6 CONTROL DIAGRAM

NOT TO SCALE

FAN COIL UNIT 2-12 (ALL) CONTROL DIAGRAM

INDICATED ON FLOOR PLANDUCTWORK OF SIZE AS

LOUVER AND DAMPERACCESS DOOR BETWEENAS INDICATED ON FLOOR PLANDAMPER OF SIZE AND TYPE

LOUVER BY GENERAL CONTR.

ST. STEEL

STAINLESS STEEL

MAKE WATERTIGHT CONNECTIONTO TOP OF WATERSTOP

WATERSTOP

SLOPE BOTTOM OF DUCTTO WATERSTOP

NOT TO SCALE

LOUVER CONNECTION DETAIL

(SEE SPEC)TRANSMITTERPRESSUREDIFFERENTIAL

PRESSURE TRANSMITTER

MAKE 1/4" CONNECTION

DIFFERENTIAL PRESSURE TRANSMITTER

RETURN

TO DIFFERENTIAL

SUPPLY

TYPICAL FOR HOT WATER ANDCHILLED WATER SYSTEMS. SEEFLOOR PLANS FOR LOCATIONS.

PRESSURE TEST

BALL VALVE (TYP.)

STATION (TYP.)

TRANSMITTER LINE COPPER TUBING

EQUALIZER

TRANSMITTER LINE

VALVE

NOT TO SCALE

FLEXIBLE CONNECTION

AIR COOLED CONDENSING UNIT

NOT TO SCALE

ROOF CURB DETAIL

W/ 2" MINIMUM OVERLAP OVERGALVANIZED STEEL COUNTERFLASHING

12" HIGH X 3" WIDE ROOF CURB

ROOF MEMBRANE.

DIMENSIONS BEFORE INSTALLINGVERIFY ALL EQUIPMENT

ROOF MEMBRANE

2X8" DOUBLE BLOCKING

4" FIBER CANT STRIP

ROOF MEMBRANE

FLASHING

ROOFING

DUCT WORK

FLASHING

G.I. LOCK

DUCT INSULATION

GALV. SHEET METAL

SHEET METAL SCREWS.

45°

ROOF DUCT PENETRATION/CURB DETAILNOT TO SCALE

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

M2.0

MECHANICAL

SECTIONS AND

DETAILS

DTS

RETURN

AIR

OUTSIDE

AIR

SUPPLY

AIR

PTTS (TYP)

AO

DTR

TT

AI

M

DO

ROOM

TEMPERATURE

SENSOR

AI

T

ON/OFF

TT-1

T-1

TCV

FAN COIL UNIT TO BE PROVIDED BY MECHANICAL CONTRACTOR WITH DDC

TERMINAL CONTROLLER AND MODULATING CONTROL VALVES

DTS

RETURN

AIR

SUPPLY

AIR

PTTS (TYP)

AO

DTR

TT

AI

M

DO

ROOM

TEMPERATURE

SENSOR

AI

T

ON/OFF

TT-1

T-1

TCV

FAN COIL UNIT TO BE PROVIDED BY MECHANICAL CONTRACTOR WITH DDC

TERMINAL CONTROLLER AND MODULATING CONTROL VALVES

03/09/2017

03/09/2017

FLOOR PIPING PENETRATION DETAILNOT TO SCALE

WALL PIPING PENETRATION DETAILNOT TO SCALE

HANGER DETAILNOT TO SCALE

THROUGH-PENETRATION FIRESTOPSYSTEMSNOT TO SCALE

PATCH AND MAKE WATERTIGHT.CORE DRILL OPENING,CEILING WITHIN BLDG

NOTE:INSTALL PIPING ABOVE

WITHIN UNITREFRIGERANT PIPINGMAKE CONNECTION TO

ROOF

BUILDING ROOF

FCU 2-6

ACCU

PITCH SUCTION LINE@ 1/2" PER 10 FOOT

NOT TO SCALE

REFRIGERANT PIPING DIAGRAM

ROOF CURB

SUCTION SIZED PERMANUFACTURER'SRECOMENDATIONS.

LIQ. SIZED PERMANUFACTURER'SRECOMENDATIONS.

SUCTION SIZED PERMANUFACTURER'SRECOMENDATIONS.

LIQ. SIZED PERMANUFACTURER'SRECOMENDATIONS.

CEILING210

NOT TO SCALE

EXHAUST FAN CONTROL DIAGRAMREVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

M2.1

MECHANICAL

SECTIONS AND

DETAILS

3

4B

A

4A

A

2

4A

3

2

4B

1

U.L. SYSTEM NO. CAJ1193

1. FLOOR OR WALL ASSEMBLY - MIN. 4-1/2" IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT

(100 - 150 PCF) CONCRETE

FLOOR OR MIN. 5" THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT CONCRETE WALL. WALL

MAY ALSO BE

CONSTRUCTED OF ANY UL CLASSIFIED CONCRETE BLOCKS, MAX. DIAM. OF OPENING IS 10".

2. METALLIC SLEEVE - (OPTIONAL) - NOM. 16" IN DIAM. (OR SMALLER) SCHEDULE 10 (OR HEAVIER) STEEL

SLEEVE CAST OR

GROUTED IN TO FLOOR OR WALL ASSEMBLY FLUSH WITH FLOOR OR WALL SURFACES.

3. THROUGH PENETRANT - ONE METALLIC PIPE, CONDUIT OR TUBING TO BE INSTALLED EITHER

CONCENTRICALLY OR

ECCENTRICALLY WITHIN THE FIRESTOP SYSTEM. THE ANNULAR SPACE BETWEEN PIPES, CONDUITS

OR TUBING AND

PERIPHERY OF OPENING SHALL BE MIN. 1/2" TO MAX. 2-1/4". PIPE, CONDUIT OR TUBING TO BE RIGIDLY

SUPPORTED ON

BOTH SIDES OF FLOOR OR WALL ASSEMBLY. THE FOLLOWING TYPES AND SIZES OF METALLIC PIPES,

CONDUITS OR TUBING

MAY BE USED:

A. STEEL PIPE - NOM. 12" DIAM. (OR SMALLER) SCHEDULE 10 (OR HEAVIER) STEEL PIPE.

B. CONDUIT - NOM. 4" DIAM. (OR SMALLER) STEEL ELECTRICAL METALLIC TUBING OR NOM. 6" DIAM. (OR

SMALLER) STEEL

CONDUIT.

4. FIRESTOP SYSTEM - THE FIRESTOP SYSTEM SHALL CONSIST OF THE FOLLOWING:

A. PACKING MATERIAL - MIN. 4" THICKNESS OF MIN. 4 PCF MINERAL WOOL BATT INSULATION FIRMLY

PACKED INTO OPENING AS A PERMANENT FORM. PACKING MATERIAL TO BE RECESSED FROM TOP

SURFACE OF FLOOR OR FROM BOTH SURFACES OF WALL AS REQUIRED TO ACCOMMODATE THE

REQUIRED THICKNESS OF FILL MATERIAL.

B. FILL, VOID, OR CAVITY MATERIAL - CAULK - MIN. 1/2" THICKNESS OF FILL MATERIAL APPLIED WITHIN

THE ANNULUS FLUSH WITH TOP SURFACE OF FLOOR OR WITH BOTH SURFACES OF WALL

ASSEMBLY.

NELSON FIRESTOP PRODUCTS - CK N/S (NON-SAG) CAULK FOR USE IN FLOORS OR WALL OR CLK S/L

(SOFT-LEVELING) CAULK FOR USE IN WALLS ONLY.

U.L. SYSTEM NO. CAJ1193 F

RATING - 2 HR. T RATING - 0 HR.

SECTION A-A

1 1/2"

1/2" MAXIMUM

INSULATION

FIBERGLASS

SAFING INSULATION

TIGHTLY PACKED

FLOOR

FINISHED

FIRE

SEALANT

INSULATED

PIPE

UNINSULATED

PIPE

BE FLUSH WITH

FINISHED FLOOR

ALL PIPE SLEEVES

THAT FALL WITHIN

PARTITIONS SHALL

4 LOCATIONS/90 DEG. APART

2" WIDE STEEL TABS

WELDED TO SLEEVE

PIPE SLEEVE INSTALLED

IN CONCRETE SLAB.

RETARDENT

CORE DRILL OPENINGS

TO INSTALL SLEEVE.

PROVIDE PATCHING AS REQUIRED.

SEE ARCHITECTURAL DRAWINGS

FINISHED INTERIOR WALL

SAFING INSULATION

TIGHTLY PACKED

SEALANT

1 1/2"

FOR WALL TYPES.

OPENINGS AS REQUIRED.

PROVIDE PATCHING FOR

TO INSTALL SLEEVE AND

RETARDENT

INSULATED

PIPE

FIRE

UNINSULATED

PIPE

PROVIDE PIPE SLEEVE

INSTALLED WITHIN WALL.

CUT WALL OPENINGS

FIBERGLASS

INSULATION

1/2" MAXIMUM

EXCEED THE SCHEDULED

SPACING SHALL NOT

MAXIMUM DISTANCE

NUT WITH FENDER

WASHER

STEEL DECK

THREADED ROD.

DIAMETER AS

SCHEDULED.

CONCRETE

REINFORCED

3-4"

ROOM OCCUPANCY SENSOR,WHERE MULTIPLE EXHAUST FANSSHALL RUN IF ONE ROOM ISOCCUPIED.

DI

OCC

EXHAUST FAN

EAEA FROM MUA-1

DO

DI

ON/OFF

STATUS (VIA CTS)

BACKDRAFT DAMPER

WHERE APPLICABLESEE EXH. FAN SCHEDULE

EF-1

OCC-1

OCCUPANCY SENSOR TO BE PROVIDED BY LIGHTINGCONTRACTOR WITH POINT FOR CONTROLS CONTRACTORINTERFACE. FOR OCCUPANCY TYPE REFER TO ELECTRICALDRAWINGS PER SCHOOL.

03/09/2017

03/09/2017

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

M4.0

MECHANICAL

SCHEDULES

03/09/2017

03/09/2017

UNEXCAVATED

UNEXCAVATED

UNEXCAVATED

EXISTING TUNNEL

UNEXCAVATED

UNEXCAVATED

UNEXCAVATED

EXIST EF-3

EXIST UH-1

LP-B1-10,12,14

LP-B1

LP-B1-10,12,14

VFD VFD

EXIST

DTP-3

1.5HP

208V-3Ø

NEW

DTP-4

1.5HP

208V-3Ø

NEW

1 1

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

BASEMENT POWER PLAN

SCALE: 1/8" = 1'-0"

N

EP1.B

ELECTRIC

POWER

BASEMENT PLAN

DRAWING NOTES:

1. NEW VFD PROVIDED BY MECHANICAL CONTRACTOR INSTALLED BY ELECTRICAL CONTRACTOR.

03/09/2017

03/09/2017

206

208

216

207

223

219

222

220

220B

218

221

220C

204A

209

210

214

205

201

202

212

217

204

211

213

213A

205A

203

218A

217A

215

212A

219

1

1

1

1

1

1

1 1 1

LP-2A

LP-2B

EXISTING

EXISTING 1

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

SECOND FLOOR POWER DEMO PLAN

SCALE: 1/8" = 1'-0"

N

EPD1.2

ELECTRIC

POWER

SECOND FLOOR DEMO

PLAN

DRAWING NOTES:

1. E.C. TO DISCONNECT EXISTING FAN COIL UNITS. FIELD COORDINATE WITH MECHANICAL CONTRACTOR.

03/09/2017

03/09/2017

206

208

216

207

223

219

222

220

220B

218

221

220C

204A

209

210

214

205

201

202

212

217

204

211

213

213A

205A

203

218A

217A

215

212A

219

1

1

1

1

1

1

1 1 1

FCU-2-6

2B-20

LP-2A

LP-2B

2

EXISTING

EXISTING 1

NEW

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

SECOND FLOOR POWER PLAN

SCALE: 1/8" = 1'-0"

N

EP1.2

ELECTRIC

POWER

SECOND FLOOR PLAN

DRAWING NOTES:

1. CONNECT NEW FAN COIL UNIT AND NEW DISCONNECT TO EXISTING CIRCUIT, REWORK CIRCUIT AS REQUIRED. FIELD COORDINATE WITHMECHANICAL CONTRACTOR. NEW DISCONNECT PROVIDED BY MECHANICAL CONTRACTOR INSTALLED BY ELECTRICAL CONTRACTOR.

2. FCU-2-6 LOCATED ABOVE CEILING. NEW DISCONNECT PROVIDED BY MECHANICAL CONTRACTOR INSTALLED BY ELECTRICALCONTRACTOR. COORDINATE INSTALLATION WITH MECHANICAL CONTRACTOR.

03/09/2017

03/09/2017

(3A-37,39,41)

36

(3A-36)

36

EXISTINGCONTROLPANEL

(3A-38,40,42)

EXISTING PHOTO CELL MTD.

4-#8,1"C.

EXISTING CONTROL PANEL

EXISTING MAGNETIC STARTER ANDDISCONNECT SWITCH COMBINATIONS

(3A-8,10,12)

EXISTING EXHAUST FAN

EXISTING T-STAT

ROOF BELOW

NEW ACCU-2-6ON ROOF

LP-2B-21, 23

1

EXISTING NEMA 1 60A., 3P. NON-FUSIBLE DISCONNECT SWITCH

NEW EF-1

ACU-126.0 MCA

208V, 3PH.MUA-1

24.8 MCA208V, 3PH.

EX

EX

EXLP-2B-22, 24

LP-2B-25WP/GFCI

WP

VFD

2

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

ROOF POWER PLAN

SCALE: 1/8" = 1'-0"

N

EP1.R

ELECTRIC

POWER

ROOF PLAN

DRAWING NOTES:

1. NEW WEATHER-PROOF DISCONNECT PROVIDED AND INSTALLED BY ELECTRICAL CONTRACTOR. FIELD COORDINATE LOCATION WITHMECHANICAL CONTRACTOR.

2. NEW VFD PROVIDED BY MECHANICAL CONTRACTOR INSTALLED BY ELECTRICAL CONTRACTOR.

03/09/2017

03/09/2017

REVISIONS

ISSUANCES

Motz Engineering

300 West 4th Street, Suite 300

Cincinnati, OH 45202-2666

T: 513.621.5400

F: 513.621.5407

MEP Design Security Sustainable Design

Commissioning Design/Build

DATE DESCRIPTION

SHEET TITLE

SHEET #

DATE

SCALE

DRAWN BY

PROJECT NO.

MEO

XU.2015.02

NO.

DATE DESCRIPTION

05.26.16 FOR OWNER REVIEW

HVAC

IMPROVEMENTS

FOR

SECOND FLOOR

AT

SCHMIDT HALL

Not Published. All Rights Reserved. This Document is the product

and exclusive property of the Engineer. This document and the

information it contains may not be copied or used for other than the

specific purpose for which it was prepared without express written

consent of Motz Consulting Engineers, Inc. doing business as Motz

Engineering.

Because the information stored in electronic formats can be modified

by other parties, intentionally or otherwise, Motz Engineering shall

not be held responsible or liable for any defects and/or deficiencies

that may arise as a consequence of downloading of this information.

Motz Engineering assumes no responsibility with regard to the

transmission or receipt of the information attached.

COPYRIGHT © 2017 MOTZ ENGINEERING

FOR

XAVIER UNIVERSITY

1518 HERALD AVE

CINCINNATI, OHIO

45207

AS SHOWN

03.09.17 FOR BID AND PERMIT

E3.1

ELECTRIC

SINGLE LINE AND PANEL

SCHEDULES

PANEL: LP-2A 208/120V, 3PH, 4W

LOCATION: SECOND FLOOR MAIN SIZE: 225A

MOUNTING: SURFACE MOUNT MAIN TYPE: MLO

NOTES:

KVA

1 LTS 207, 206 20/1 1.35 A 1.35 20/1 LTS 203-205, 208-210 2

3 LTS 219, 319, 222 20/1 1.35 B 1.30 20/1 LTS 216, 217 4

5 LTS 201 20/1 1.20 C 1.20 20/1 LTS 218 6

7 LTS 221 20/1 1.20 A 1.30 20/1 LTS 211-213 89 LTS 220 20/1 1.20 B 1.20 20 LTS 214 10

11 LTS 220 20/1 1.20 C 1.20 20/1 LTS 214 12

13 LTS 220 20/1 1.20 A 0.00 20/1 SPARE 14

15 LTS 223 20/1 1.20 B 0.00 16

17 LTS 223 20/1 1.20 C 0.00 60/3 SPARE DIMMER PANEL 18

19 LTS 223 20/1 1.20 A 0.00 20

21 RCPTS 206, 217, 216 20/1 0.90 B 0.72 20/1 RCPTS 217, 218 22

23 RCPTS 217, 216, 208 20/1 0.90 C 0.72 20/1 RCPTS 217, 218 24

25 COPIER 218 20/1 1.50 A 0.90 20/1 RCPTS 218, 220, 221 26

27 FRIDGE 218 20/1 1.20 B 0.90 20/1 RCPTS 218, 220, 221 28

29 RCPTS 220, 220C, 221 20/1 0.90 C 0.54 20/1 RCPTS 222 30

31 RCPTS 220, 221 20/1 0.90 A 0.54 20/1 RCPTS 222 32

33 RCPTS 222 20/1 0.90 B 0.54 20/1 RCPTS 216 34

35 FAN COILS 207, 216, 218 20/1 1.20 C 0.90 20/1 RCPTS 220 36

37 FAN COILS 210, 201, 214, 221 20/1 1.20 A 0.50 20/1 BOARDROOM BLINDS 38

39 BOARDROOM BLINDS 20/1 0.50 B 0.50 20/1 BOARDROOM BLINDS 40

41 PHONE RCPT 20/1 0.36 C 0.50 20/1 BOARDROOM BLINDS 42AMPS PER PHASE: 109.5 103.42 100.17

LOAD TYPE CONNECTED KVA DEMAND KVA

LIGHT at 125% 19.9 24.8

RECPT. (100% 1st 10KVA + 50% REMAINING) 33.5 21.7

MOTOR (100% + 25% OF LARGEST) 0.0 0.0

EQUIPMENT NON-CONTINUOUS. (100%) 0.0 0.0

EQUIPMENT CONTINUOUS. (125%) 0.0 0.0

HEAT (100%) 8.5 8.5

KITCHEN 0.0 0.0

TOTAL KVA 61.8 55.0

TOTAL AMPS 171.6 152.8

PANEL: LP-2B 208/120V, 3PH, 4W

LOCATION: SECOND FLOOR MAIN SIZE: 225A

MOUNTING: SURFACE MOUNT MAIN TYPE: MLO

NOTES:

* FURNISH AND INSTALL NEW CIRCUIT BREAKER

KVA

1 FRIDGE 209 20/1 1.00 A 1.00 20/1 MICROWAVE 209 2

3 ICE MAKER 209 20/1 1.00 B 1.00 20/1 DISHWASHER 209 4

5 DISPOSAL 209 20/1 0.80 C 1.08 20/1 RCPTS 201, 203, 206, 209, 210 6

7 RCPTS 212-214 20/1 0.90 A 1.08 20/1 RCPTS 204, 208, 210-212 89 RCPTS 212-214 20/1 0.90 B 0.90 20/1 SCREEN & RCPTS 10

11 RCPTS 209 20/1 0.90 C 1.00 20/1 ICE MAKER 209 12

13 RCPT 209 20/1 0.90 A 1.00 20/1 FRIDGE 209 14

15 RCPT 209 20/1 0.90 B 0.90 20/1 RCPT 209 16

17 RCPT 209 20/1 0.90 C 0.90 20/1 RCPT 209 18

19 RCPT 209 20/1 0.90 A 0.48 20/1 *

(NEW) FCU-2-6 20

21 (NEW) ACCU-2-6 * 30/2

1.88 B 0.92 20/2 *

(NEW) EF-1 22

23 1.88 C 0.92 24

25 ROOFTOP RCPT * 20/1 0.18 A 0.00 SPACE 26

27 SPACE 0.00 B 0.00 SPACE 28

29 SPACE 0.00 C 0.00 SPACE 30

31 SPACE 0.00 A 0.00 SPACE 32

33 SPACE 0.00 B 0.00 SPACE 34

35 SPACE 0.00 C 0.00 SPACE 36

37 SPACE 0.00 A 0.00 SPACE 38

39 SPACE 0.00 B 0.00 SPACE 40

41 SPACE 0.00 C 0.00 SPACE 42AMPS PER PHASE: 62.0 69.98 69.81

LOAD TYPE CONNECTED KVA DEMAND KVA

LIGHT at 125% 0.0 0.0

RECPT. (100% 1st 10KVA + 50% REMAINING) 18.1 14.1

MOTOR (100% + 25% OF LARGEST) 0.0 0.0

EQUIPMENT NON-CONTINUOUS. (100%) 0.0 0.0

EQUIPMENT CONTINUOUS. (125%) 0.0 0.0

HEAT (100%) 6.1 6.1

KITCHEN 0.0 0.0

TOTAL KVA 24.2 20.1

TOTAL AMPS 67.3 56.0

1. LIGHTING LOAD

1.2 LP-1A1.3 LP-1B1.4 LP-2A, LP-2B1.5 LP-3A1.6 ELP-1A1.7 SUBTOTAL LIGHTING LOAD1.8 PLUS 25% OF 44,701 VA1.9 N.E.C. TOTAL LIGHTING LOAD

2. RECEPTACLE LOAD

2.2 LP-1A2.3 LP-1B2.4 LP-2A, LP-2B2.5 LP-3A2.6 ELP-1A2.7 SUBTOTAL NON-DERATED APPLIANCE LOAD2.8 FIRST 10,000 VA AT 100%2.9 REMAINDER AT 50% (78,222VAx0.5)2.10 N.E.C. TOTAL APPLIANCE LOAD

3. AIR CONDITIONING LOAD

3.2 LP-1A3.3 LP-1B3.4 LP-2A, LP-2B3.5 LP-3A3.6 ELP-1A3.7 SUBTOTAL OF AIR CONDITIONING LOAD3.8 PLUS 25% OF LARGEST SINGLE LOAD3.9 N.E.C. TOTAL AIR CONDITIONING LOAD

4. TOTAL N.E.C. LOAD

5. CONVERT TO AMPERES AT 208V., 3 PHASE (166,638VA/360V)

5,849 VA

19,850 VA

7,473 VA

6,009 VA

4,800 VA

-

33,280 VA26,292 VA

16,620 VA

11,550 VA

8,474 VA -

18,738 VA

12,828 VA

-

44,701 VA11,175 VA

88,222 VA 10,000 VA 39,411 VA

59,258 VA 2,093 VA

55,876 VA

49,411 VA

61,351 VA

166,638 VA

462.9 AMPERES

N.E.C. CALCULATION - (DP-1)

1.1 LP-B1 720 VA

2.1 LP-B1 1,080 VA

3.1 LP-B1 19,218 VA

PANEL: LP-B1 208/120V, 3PH, 4W

LOCATION: BASEMENT MAIN SIZE: 225A

MOUNTING: SURFACE MOUNT MAIN TYPE: MLO

NOTES:

* FURNISH AND INSTALL NEW CIRCUIT BREAKER

KVA

1 EXISTING LOAD 15/1 0.36 A 0.00 2

3 EXISTING LOAD 15/1 0.36 B 0.00 100/3 EXISTING LOAD 4

5 SPACE 0.00 C 0.00 6

7 SPACE 0.00 A 0.72 20/1 EXISTING LOAD 8

9 SPACE 0.00 B 1.66 10

11 SPACE 0.00 C 1.66 20/3 *

DTP-3, DTP-4 12

13 SPACE 0.00 A 1.66 14

15 JOHNSON CORTOL FOR USD 20/1 0.18 B 0.00 SPACE 16

17 SPACE 0.00 C 0.00 SPACE 18

19 SPACE 0.00 A 0.00 SPACE 20

21 SPACE 0.00 B 0.00 SPACE 22

23 SPACE 0.00 C 0.00 SPACE 24

25 SPACE 0.00 A 0.00 SPACE 26

27 SPACE 0.00 B 0.00 SPACE 28

29 SPACE 0.00 C 0.00 SPACE 30

31 SPACE 0.00 A 2.50 32

33 SPACE 0.00 B 2.50 60/3 EXISTING LOAD 34

35 TV POWER SUPPLY 20/1 0.18 C 2.50 36

37 SPACE 0.00 A 2.25 38

39 SPACE 0.00 B 2.25 50/3 EXISTING LOAD 40

41 SPACE 0.00 C 2.25 42AMPS PER PHASE: 62.4 57.88 54.88

LOAD TYPE CONNECTED KVA DEMAND KVA

LIGHT at 125% 0.7 0.9

RECPT. (100% 1st 10KVA + 50% REMAINING) 1.1 1.1

MOTOR (100% + 25% OF LARGEST) 0.0 0.0

EQUIPMENT NON-CONTINUOUS. (100%) 0.0 0.0

EQUIPMENT CONTINUOUS. (125%) 0.0 0.0

HEAT (100%) 19.2 19.2

KITCHEN 0.0 0.0

TOTAL KVA 21.0 21.2

TOTAL AMPS 58.4 58.9

N.E.C. CALCULATION - (SWITCHBOARD)

1. HINKLE HALL LOAD

2. EDGECLIFF LOAD

3. SCHMIDT HALL (DP-1) LOAD

381.7 AMPERES

296.4 AMPERES

462.9 AMPERES

4. TOTAL N.E.C. LOAD 1,141 AMPERES

*EC TO COORDINATE FEEDER BREAKER TYPE (THERMAL MAG/M.C.P.), SIZE RATING WITH VFD MANUFACTURER

"B""A"3Ø

PANEL

OTHER INTERLOCKS OR SAFETIES**

CONTROL FROM DDC SYSTEMWIRED IN "AUTO" POSITION**

REFER TO CONTROL DIAGRAMSFOR CONTACT TYPE AND OPERATIONSEQUENCE

**CONTROL RACEWAYS AND WIRING BY CONTROLS CONTRACTOR

PER SPECIFICATIONS, PROVIDE SHIELDED1000V RATED VFD CABLE & SIGNAL CABLEVFD RATED HIGH EFFIC. DESIGN B WITHBEARING GROUNDING RINGS PER SPECIFICATIONS

PROVIDE INDIVIDUAL EUTECTIC THERMAL MOTOR OVERLOADSWHERE MULTIPLE MOTORS ARE CONNECTED TO A SINGLE OUTPUT

VFD RATING 110%AFTER DERATINGFACTORS

VFD

FUSED DISC.SW.

WIRING DIAG - VFD MOTORS

COMPONENTS, RACEWAYS & WIRING BY EC

DTP-3, DTP-4, EF-1

03/09/2017

03/09/2017