modem configuration

8/10/2019 Modem Configuration

1/11

NIIT TechnologiesLtd.

VPN MODEM CONFIGURATION


2/11


Prerequisites -:

The following items are necessary for MODEM configuration-:

1. MODEM.

2. Adapter.

3. LAN Cable (Used to connect MODEM and SWITCH).

4. Telephone Line.

5. Computer.

MODEM-:

DSL

INTERNET

EATHERNET

USB

DSL Port

Telephone Line LAN Cable

Eathernet Port USB

RESET

Power Switch

Power Port

Power Cable


3/11


Follow the below steps to configure the MODEM -:

1. As per the picture-:

a. Plug the Telephone Line in DSL Port of MODEM.

b. Plug the any one side of LAN Cable in Ethernet Port of MODEM and

another side in Computer LAN Port.

c.

Plug the Adapter in Switch board and plug the end side of Adapter in

Power Port of MODEM.

2. First turn on the Power from Adapter and then from MODEM by pressing the

Power Button.

3. Wait till all the lights of MODEM turned ON.

4. Now Open Run Prompt ( + R) in your computer and type ncpa.cpland press

enter. This will open Network Connectionsin computer.

5. Here you will find Local Area Connection. Now right click on Local Area

Connection and click on Properties.

6. After clicking on Properties below window open, now double click on Internet

Protocol Version 4 (TCP/IPV4).


4/11


7. Now below window will appear, here click on Use the following IP Address and fill

the IP details as follows-:

IP Address 192.168.1.2

Subnet Mask 255.255.255.0

Default Gateway 192.168.1.1

8. Now click on OK and again OK to save the settings.

9. Now click on Start All Programs .

10.Now in URL type 192.168.1.1 and press Enter.


5/11


11.Now it will prompts for entering the Username and Password. In Username type

admin and in Password type admin. Click OK.

12.After Clicking OK below MODEM configuration page will open.

13.Now click on Advance Options and then click Edit.


6/11


14.After clicking on Edit below page will open, here keep the settings as per the

below picture. Now on Next.

15.Now below page will appear. Here Click on PPP over Ethernet (PPPoE)and then

click on Next.


7/11


16.Now below page will appear. Do the following settings and click Next.

a. PPP Username -(as given by BSNL for your Location)

b. PPP Password -password

c. PPPoE Service Name -dataone

d. Authenticate Method -Auto.

e.

Check Enable Fullcone NAT.

f. CheckBridge PPPoE Frames Between WAN and Local Ports (Default

Enabled) and MTU Size [576-1492]should be 1492

17.

Now below window will appear. Do the following settings and click Next.

a. Check IGMP Multicast.

b. Check Enable WAN Services.


8/11


18.Now below window will appear. Click here on Save.

19.After clicking on Save below page will appear. Click on LANhere than Do the

following settings and then click Save/ Reboot.

a. IP Address- 10.234.XXX.XXX (As per the details provided by BSNL)

b. Subnet Mask- 255.255.255.XXX (As per the details provided by BSNL)

c. Check Enable IGMP Snooping.

d.

Check Blocking Mode.

e. Check Disable DHCP Server.


9/11


20.Now Open Run Prompt ( + R) in your computer and type ncpa.cpland press

enter. This will open Network Connectionsin computer.

21.Here you will find Local Area Connection. Now right click on Local Area

Connection and click on Properties.

22.

After clicking on Properties below window open, now double click on InternetProtocol Version 4 (TCP/IPV4).

23.Now below window will appear, here click on Use the following IP Address and fill

the IP details as follows-:

IP Address 10.234.XXX.XXX (As per the details provided by BSNL)

Subnet Mask 255.255.255.XXX (As per the details provided by BSNL)


10/11


Default Gateway 10.234.XXX.XXX (As per the details provided by BSNL)

24.Now click on OK and again OK to save the settings.

25.Now click on Start All Programs .

26.Now in URL type 192.168.75.101/cctnsweb/login.aspx and press Enter then

CAS Online will open.


11/11


In case of facing any issue in understanding the document or MODEM configuration

call @ 1800-3000-5050 UP CCTNS HELPDESK Toll Free Number.

THANK YOU

modem configuration

Documents