model 4450 jaw crusher 4450 jaw crusher. page ... 4450 jaw 408531 use ib229 for operation manual g...

page

Replacement Parts

Model 4450

Jaw Crusher

page

Your equipment serial number and order number have been recorded in

the space below. Please include these numbers when requesting service

or ordering parts.

MANUFACTURED BY KOLBERG-PIONEER, Inc. YANKTON, SD, U.S.A.

JOB ORDER

MODEL S/N

KOLBERG-PIONEER, INC.

4085314450 Jaw

Use IB229 for Operation Manual

g

603712

Serial Number Plate Location

RearFront

page

This bulletin contains replacement parts listings for your equipment. In most cases an

illustration is used to identify the assembly, with each illustration is a parts list identifying

serviceable parts.

In some cases no illustration is available or required and just a parts list is shown.

When a part name is indented, it means the serviceable item is a part of the item under

which it is listed. The quantity of parts shown with these indented items are for the assem-

bly only and not the entire machine.

EXAMPLE:

Ref.No. Description Part No. Qty. 1 Coupling Assembly AEP-19630 2

Coupling Flange 44-25039 2

Bushing 44-25053 1

Abbreviations and Symbols Used In This Parts Book

* See notes at bottom of page

N/S Not Serviced

X Parts not exactly as shown

O/E Optional Equipment

P/N Part Number

KOLBERG-PIONEER, INC. reserves the right to make changes or add improvements to

its products at anytime, without incurring any obligation to make such changes on previ-

ously manufactured equipment.

Although care has been taken to assure the accuracy of this publication, KOLBERG-

PIONEER, INC. does not assume any liability for errors or omissions.

Quantity for machine

Quantity for assemblyThis item contains

these items.

INTRODUCTION

g

page

CONTENTS

g

ORDERING PARTS .............................................................................................................. 1

JAW CRUSHER BASE ......................................................................................................... 2

WEDGE ADJUST ASSEMBLY ............................................................................................. 3

WEDGE ADJUST WEAR LINERS AND TOGGLE PLATE .................................................... 4

TENSION ROD ASSEMBLY.................................................................................................. 5

FLYWHEEL ASSEMBLY DRIVE ........................................................................................... 6

FLAT FLYWHEEL ASSEMBLY.............................................................................................. 7

WEAR LINERS .................................................................................................................. 8-9

JAW WEDGE AND JAW PLATES ................................................................................. 10-11

PITMAN / SHAFT ASSEMBLY ....................................................................................... 12-13

HYDRAULIC ADJUST ASSEMBLY ................................................................................ 14-15

page

ORDERING PARTS

We want to service your equipment promptly and accurately. Your observance

of the instructions below will greatly aid us in giving you such parts service.

When ordering parts be sure you supply the following:

(A) Part Numbers, (B) Descriptions, (C) Quantities

(D) Serial Numbers, (E) Shipping Instructions.

(A) PART NUMBERS

Compare part number found on the part with part number in the parts book,

whenever possible. When part number is not available, give full description and

where used.

(B) DESCRIPTIONS

Use Part Book descriptions in addition to part numbers. Most structural parts,

such as framework, gussets, braces etc., are not listed. To order such parts, give

size, shape (channel, angle, plate, etc.), and location, as related to units or

groups identified in the parts book.

(C) QUANTITIES

Be specific. State exactly how many of each part are required. Avoid the

use of words like “sets” or “complete”.

(D) Identify your equipment by Serial Number whenever possible.

(E) SHIPPING INSTRUCTIONS

Specify name, shipping point, and mail address for notification if different

than shipping point. State whether freight, express, parcel post or other handling is

desired. Confirm telephone orders in writing.

INSPECTION

Shortages or damage should be noted by the carrier agent at time material

is accepted. Shipper’s responsibility ceases upon delivery of shipment to carrier

in good order. Claims for damage or loss can likely be collected with proper

notation on delivery receipt.

ORDER EARLY

Make periodical inspections of equipment. Wear parts can be ordered by

mail ahead of actual replacement time. Save on telephone expense and have

material on hand when needed.

1

JAW CRUSHER BASE

Ref.No. Description Part No. Qty.

1 Base, Jaw 210271 1

2 Bolt 151966 4

Washer 233742 4

Shear Block 211268 4

1

2

WEDGE ADJUST ASSEMBLY

WEDGE ADJUST WEAR LINERS AND TOGGLE PLATE

TENSION ROD ASSEMBLY

FLYWHEEL ASSEMBLY DRIVE

ROTATION

SECTION A-A

45-60013 WASHER

FLAT FLYWHEEL ASSEMBLY

ROTATION

SECTION A-A

45-60013 WASHER

WEAR LINERS

page

WEAR LINERS

9

JAW WEDGE AND JAW PLATES

PITMAN / SHAFT ASSEMBLY

for bolts

see jaw crusher

base page

3

25

19

23 20

2 1

6

5

918

20

2322

21

22

19 FIXED SIDEFLOAT SIDE

B

B

24

16 15

25

17

SECTION D-D

21

19

1012

16

15

7

8

1314

4

17

DETAIL B

1

1.122

2033

19735

1.8

1.9

1.10

20

22

23

33

21

19

18

16

7

35

page

PITMAN / SHAFT ASSEMBLY

13

ECCENTRIC SHAFT ASSY 206140

DESCRIPTIONQTYPART NO.ITEM

PITMAN ASSY11885651

WEAR PLATE1BB-731371.1

HEX CAPSCREW 3/4845-001691.10

WASHER;3/4845-600091.15

LOCKNUT845-421651.17

MOVING JAW KEY1WSC-010461.8

HEX CAPSCREW 3/4145-001531.9

LOCKNUT;3/4145-421611.16

PULL-OFF COLLAR2WSC-009882

BEARING209-350323

BEARING COVER2WSC-009894

FIXED END INNER COVER12061585

FLOATING END INNER COVER12061596

BEARING HOUSING2L-037767

BEARING209-350318

ADAPTOR SLEEVE, BEARING2WSC-010159

LOCKNUT209-2014010

LOCKPLATE209-2013811

SPACER COLLAR2WSC-0099112

HEX CAPSCREW 5/81045-0609313

LOCKWASHER; 5/81045-6004314

LOCKWASHER; 3/41645-6004415

CAP SCREW; 3/416CP-7238916

BRG COVER; OUT, FXD1WSC-0098617

BRG COVER; OUT, FLT1WSC-0098518

SHAFT FLINGER COLLAR2WSC-0111119

SHAFT SPACER FOR HOLDING FLYWHEEL2CP-6402720

FLYWHEEL SPACER2BB-7354121

LOCKNUT209-2009922

LOCKWASHER209-2010023

LUBE FITTING243-0001524

PIPE PLUG,247-1802625

CAPSCREW; 5/864AA-5570626

SETSCREW; 5/8445-3603127

BRASS WASHER; 5/86445-6009028

STAINLESS STEEL WIRE35'303429

STR KEY220614532

ECC. SHAFT, W/LOCKNUTS120615333

SHAFT FLINGER COLLAR220615534

CLOSURE BAND ON PILLOW BLOCK220615435

page

HYDRAULIC ADJUST ASSEMBLY

14

page

HYDRAULIC ADJUST ASSEMBLY

15

- 265691 1 POWER UNIT

Replaceable Parts for Motor 265691

Motor 213640

Pump 218200

Coupling 224239

Replaceable Parts

for Valve 202600

Handle 240945

page

g

FFFFFor Seror Seror Seror Seror ServiceviceviceviceviceKPI -Toll free - 800-532-9311 (605-665-9311)

Fax- 800-514-6115 (605-665-9348)

JCI - Toll free - 866-875-4058 (541-736-1400)

Fax - 541-988-9501

FFFFFor Por Por Por Por PararararartststststsKPI - Toll free - 800-766-9793 (605-665-9793)

Fax - 605-665-9348

JCI - 888-474-0115 (541-736-1400)

Fax - 541-988-9487

5/07

model 4450 jaw crusher 4450 jaw crusher. page ... 4450 jaw 408531 use ib229 for operation manual g...

Documents