mns low voltage distribution board and power cabinet · 2018. 6. 14. · ax.30ka max.63ka 50hz...
TRANSCRIPT
—Low Voltage System
MNS® Low Voltage Distribution Board and Power CabinetTechnical Info
— From the sub distribution to factory power supply, from the general industry to the marine, nuclear power plant, MNS® power distribution box can provide high security, high reliability of professional solutions.
3
— Content
004 – 005
004
004
005
006 – 013
007
008
009
010
012
014 – 024
014
017
025 – 028
029
Product Overview
Applicability
Product Features
Technical Parameters
Product Classification
MNS® Distribution Board
MNS® Lighting Control Board
MNS® Metering Board
MNS® Power Cabinet
Enclosures Made of Special Materials
Electrical Solutions
Electrical Solutions for Wall Mounted /
Wall Embedded
Electrical Solutions for Floor Mounted
Installation Guide
Product Credentials
4 MNS® Low Voltage Distribution Board and Power Cabinet Technical Info
Applicability Features
The ABB MNS® low voltage distribution board and power cabinet are a new set of modular and multipurpose low-voltage products. As a member of the ABB MNS family, this particular product is widely used in the lower-level power distribution facilities with MNS® low-voltage switchgear in the following industries:�
·Mining ·Wastewater treatment
·Marine ·Petrochemicals
·Utilities ·Buildings and housing complexes
ABB distribution board and power Cabinet conform to GB7251.3-2006. Product includes distribution board, lighting control panel, metering panel, and power cabinet. , They are suitable for wall mounting and floor mounting with front access. In designing the distribution board and power cabinet, ABB drew upon its wealth of experience with low-voltage switchgear and placed a strong emphasis on the product’s ease of installation, operations, maintenance, capacity expansion, and protection.
The ABB-MNS® distribution board and power cabinet are of a welded structure. The product comes in a good variety of shapes, and is highly versatile, structurally innovative, and mechanically rigid. Its enclosure is made of cold-rolled sheet steel, stainless steel, or other special materials.
—Product Overview
5
Technical Data
Standard Type-tested Assembly
ElectricalParameters
Rated voltage
Rated current
Mechanical characteristics
Material specifications
Operating Environment Shipment Temperature
Rated operation voltage_Ue
Rated impulse withstand voltage Uimp
Overvoltage category
Degree of pollution
Rated current of Main Busbar_Ie
Rated insulation voltage_Ui
Rated frequency_f
Rated short-time withstand current_Icw
Rated peak withstand current_Ipk
Surface treatment
Spraycolor Degree of protection
Installation
Installation SiteSealing material
Enclosure
Mounting plate
Door
Modular mounting
insideboard and Cabinet
Dimensions
Indoor Installation:
Minimum temperature -5℃
Relative humidity Max. 50% (+40℃)
Short-time maximum temperature +40℃
24-hour maximum average temperature +35℃
Note: Higher humidity of up to 90% (+20℃) is permissible
when temperatures are low.
Maximum temperature +55℃
Minimum temperature -25℃
Higher temperatures of up to +70℃ over a short period
(no more than 24 hours) are permissible.
Max.1000V
690V / 400V / 230V
6 / 8kVⅢ
3
Max.800A
Max.30kA
Max.63kA
50Hz
Refer to Product Manual
Bright grey
IP30-IP67Fixed
Wall mounted, wall embedded, or floor mounted
Indoor or outdoor
Neoprene or polyurethane (single-step forming)
Cold-rolled sheet steel / stainless sheet steel 1.5 -3mm
Epoxy powder electrostatic coating;
coat thickness: 90-200um
Cold-rolled sheet steel / stainless sheet steel 1.5-3mm
Alu-zinc or hot-dipped zinc plate 1.5-3mm
* Enclosures with a degree of protect above IP54 and enclosures resistant to chemical corrosion are die-cast. Specifications are available upon request.
Product Overview
GB 7251.12-2013GB/T 7251.3
MNS® Distribution Board
Structural Characteristics:
Electrical Parameters
Rated frequency 50Hz
Degree of Protection IP30-IP65
Rated operation current Max. 400A
Rated operation voltage 690V/400V/230V
Rated insulation voltage Max. 1000V
Recommended Enclosure Dimensions
Width:400 / 500 / 600 / 700mm
Height: 300 / 600 / 700 / 800 / 900mm
Depth: 150 / 200mm
Installations Wall mounted
·Wall embedded
·Wall mounted
The dual-door structure design separates live parts
from non-live parts to prevent electrical shock. All
operations can be carried out on the parts
protruding from the opening on the inner door.
For design higher than IP54, door is supplied with
special sealing.
Suitable for indoor and outdoor installation. Waterproof
awning is applied in outdoor application.
Main components include enclosure, electrical
mounting parts, electrical components, cables,
connecting terminals, and label.
Electrical components are vertically mounted.
Enclosure is made of cold-rolled or stainless sheet
steel with a thickness ranging from 1.5mm to 3mm,
which is bended and welded. Concealed hinged are
used. Door are made of a plate with a thickness
ranging from 1.5mm to 3mm, which is bended and
weld. Coated sheet steel solid welded plate. The outer
door can be opened up to 110°, while the inner door
can be opened up to 90°.
The panel is equipped with a removable flange to
facilitate top or bottom entry. Products to be mounted
on the wall or embedded in the wall come with a
wall-mounting slot, and other structures are the same.
For wall mounted, the flange is located on the external
side of the enclosure, and there is a wall mounted slot
on the back of the enclosure. For wall embedded, the
flange is located on the internal side of the enclosure,
and there is no wall mounted slot on the back of the
enclosure.
·
·
·
·
·
·
6 MNS® Low Voltage Distribution Board and Power Cabinet Technical Info
—Product Classification
Nameplate frame
Mounting bracket
Connecting terminal
Mounting plate
Enclosure
Hinge
Flange
Outer door
Inner door
Sealing strip
7Product Classification
MNS® Lighting Control Panel
Structural Characteristics:·
·
·
·
Products to be mounted on the wall come in a fully
metallic enclosure. Optimized design with
flat-cover and the concealed cover screws .
Products to be embedded in the wall come with a
metallic bottom plate and a high-quality moulded
plastic front cover which is of high rigidity and flame
retardant characteristic. Self-positioning plastic
front door make it easy for operation and
maintenace when door is open.
Terminal blocks can be arranged on the top or
bottom of the panel to suit for top entry and
bottom entry design.
Product Standard: GB7251.3-2006
Electrical Parameters
Recommended Enclosure Dimensions
8/10/13/16/20/23 modules (1 module =17.5mm)
Rated frequency 50Hz
Degree of Protection IP30-IP41
Rated operation current Max. 100A
Rated operation voltage 400V/230V
Rated insulation voltage 400V
8 MNS® Low Voltage Distribution Board and Power Cabinet Technical Info
9
MNS® Metering Panel
Structural Characteristics:·For indoor installation only.·This product’s main components include an enclosure, electrical mounting parts, electrical components, a busbar system, a metering lead seal, cables, connecting terminals, and label. ·The enclosure contains a metering unit, a main switch unit, and a user switch unit. every units have a separate structure and door. The doors can be split doors. ·The enclosure is made of cold-rolled or stainless sheet steel with a thickness ranging from 1.5mm to 3mm, which is bended and welded. Concealed hinged are used. The doors are made of a plate with a thickness ranging from 1.5mm to 3mm, which is bended and welded. The outer door can be opened up to 110°, while the inner door can be opened up to 90°. ·The dual-door structure design segregates live parts from non-live parts to prevent electrical shock. All operations can be carried out on the parts protruding from the opening on the inner door.
Electrical Parameters
Rated frequency 50HzDegree of Protection IP30 – IP42Rated current Max. 400ARated operation voltage 400V / 230VRated insulation voltage 400V
Recommended Enclosure DimensionsW: 300-1100mmH: 400-2200mmD: 150-600mm
Product Classification
10
MNS® Power Distribution Board (or Power DB)
Product suitable for indoor and outdoor installation. In outdoor application, special accessories have to apply for higher protection.Typical product includes the following components, enclosure electrical mounting parts electrical devices, busbars, cables, connecting terminals, and label. The enclosure is made of welded cold-rolled or stainless sheet steel with a thickness ranging from 1.5mm to 3mm. The doors are made of a plate with a thickness ranging from 1.5mm to 3mm, which is bended and welded. The outer door can be opened up to 110º, while the inner door can be opened up to 90º.Power DB is constructed with main busbar compartment and operating compartment for the switch and controlling equipment (for Cabinet with a dual-door structure). Toughened glass can be set on the outer door as an observation window. Power DB is equipped with a removable flange, facilitating top or bottom cable entry and exit and making it easier for the user to install cables by drilling holes onsite.
The busbar can be flexibly installed in an upper, middle or lower position on the Cabinet. For products with a protection degree above IP54, the doors will be applied with special sealing.
Electrical Parameters
Rated frequency 50HzDegree of Protection IP30 – IP65Rated operation current Max. 800ARated operation voltage 690V/400V/230VRated insulation voltage Max. 1000VRated short-time withstand current 10kA/15kA/35kARated peak withstand current 17kA/30kA/73.5kA
Recommended Enclosure DimensionsW: 600/700/800mmH: 1700/1800/2000/2200mmD: 400-600mm
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info
··
·
·
·
·
·
Structural Characteristics:
Hoisting ring
Flange
Outer door
Inner door
Busbar Bracket
Toughened glass
Sealing strip formed in a single step
Nameplate frame
Mounting plate
Mounting bracketPC baffle
PEN busbar
Enclosure
Main busbarsystem
Enclosure equipped witha transparent outer door
Equipped with a transparent outer door
Mounting plate
Blank cover
Side mounting bracket
Miniature circuit breakers assembly
Miniature circuit breakers assembly
Blank cover
Enclosures Made of Special Materials
Structural Characteristics:Advanced technologies are employed to form sealing gaskets and the enclosure concurrently. Enclosure materials include special glass fiber reinforced polyester and die-cast aluminum, as well as common PC and ABS. These enclosures are mainly used in industries requiring high levels of corrosion resistance and protection, such as petrochemicals, shipbuilding, and wastewater treatment. Protection can be up to IP67.
1.Built-in High-strength Aluminum Alloy Hinges The door can be opened up to 110º. 2.Non-interface Sealing Rings The door and its edges are protected with durable and high-elasticity non-interface sealing rings, providing a high degree of protection. 3.Earthing Stud The door and the bottom enclosure are equipped with a earthing stud to facilitate grounding .
4.Flexible Bottom mounting Plate Bottom mounting plate can be bolted. Components and acceesries are installed onto bottom mounting plate. The plate is removable and easy for drilling and components arrangement and installation. External Wall Mounting Bracket. 5.The enclosure comes with a wall mounting bracket, Plastic Plugs6.If the enclosure is mounted on the wall, the four mounting slots can be sealed up with plastics plugs to ensure a high degree of protection. 7.Cable Entry Gland Plate with Sealing Gasket Both the top and bottom of the enclosure are equipped with a cable entry gland plate protected with sealing gaskets, facilitating bottom cable entry and top cable entry while maintaining the degree of protection.
13 5
674
2
Product Classification 11
ABB Breakers Median Width Height Depth MCB rated current Mounting Degree of protection Rated short-time withstand current
19
30
54
72
95
500
400
500
600
700
300
600
700
800
900
150,200 ≤160A Wall mounted or
wall embedded
IP30–65 Icw=10kAIncoming and outgoing circuit breakers are MCB: S200-series miniature circuit breakers; residual current circuit breaker
Notes:1.The modules listed in the above table are for outgoing circuit MCBs without terminals. If outgoing terminals are required for the project, the modules should be reduced by half. 2.If T connector is used or MCCB is employed as incomer breaker, design space is to be reduced by 5 standard modular size. 3.The observation window on the outer door is optional. In outdoor applicaition waterproof awning will be applied. 4.The upper and lower flange plates are not pre-drilled but can be pre drilled upon request. 5.1 standard modular size = 17.5mm (the width of single-pole MCB)
Transparent observation window
Outer door Inner door
Upper and lower flanges (removableremovable)
Electrical Solutions for Wall Mounted / Wall Embedded
—Electrical Solutions
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info12
Transparent observation window
Outer doorInner door
Upper and lower flanges(removable)
9
3
4
6
11
500
400
500
600
700
300
600
700
800
900
150,200
Wall mounted IP30–65 Icw = 10kA≤160A
≤250A
ABB Breakers Rated current Installation Degree of protection Rated short-time withstand currentMedian Width Height Depth
The switches of both incoming and outgoing circuit are MCCB: T2, 3P
Notes:1.The modules listed in the above table are for outgoing MCBs without without terminals. If outgoing terminals are required for the project, the modules should be reduced by one third. 2.The observation window on the outer door is optional In outdoor application, waterproof awning will be applied 3.The upper and lower flange plates are not pre-drilled but can be pre drilled upon request.. 4.In the case of 500X700 with one single switch installation current rating can be up to 250A. In the case of 600X800 with one single switch installation, the current rating can rise up to 400A. In the case of 700X900 it goes to 630A.
13Electrical Solutions
ABB Breakers
Main switchcurrent rating
Installation Degree ofprotection
Rated short-timewithstand current
Number of motor circuits
Width Height Depth
1
2
3
4
5
500
400
500
600
700
300
600
700
800
900
200 ≤160A IP30 –65 Icw=10kAThe switches of both incoming and outgoing circuits are:1.MCCB: T2, 3P2.MCB: S200-series switches, MS-series motor starters
Wall mountedDegree ofprotection
Notes:1.The observation window on the outer door is optional. In outdoor application, waterproof awning will be applied are not pre-drilled but can be pre drilled upon request. 2.Each motor circuit is equipped with two lights, two buttons, and one changeover switch; one contactor is less than A50.3.One thermal overload relay; and there are 20 terminals. The dimensions should be increased if this configuration is exceeded.
Transparent observation window
Outer doorInner door
Upper and lower flanges(removable)
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info14
Solution No. 01
Main Circuit DiagramMCCB Incoming, bustie
QF
TAa~TAc
500
A
T2,3~4P,FF进线开关
T2,3~4P,FF T3,3~4P,FF T3,3~4P,FF
A A V
750
AAA A V
650
VAA AAA V
T5,3P,FF/T6,3P,FF
AA A V
Incoming switch (MCCB) Incoming switch (MCCB) Incoming switch (MCCB) Incoming switch (MCCB) Incoming switch (MCCB)
Purpose
400
Setup of components in Cabinet
12.5 -160A 32 - 250A 320 - 630A
.
T6 800.3Por 4P.FF
LNC4
#
#
#
T3 250.3Por 4P.FF
LNC2
#
#
#
1
2
3
4
5
6
7
8
9
10
11
12
600X
Breaker
Attachment
Incoming
Cabinet depth(mm)
Segregated
Maximum rated current(A)
Model & specs Qty Model & specs Qty. Model & specs Qty. Model & specs Qty. Model & specs Qty.
Contactor
Thermal overload relays
Soft starter
VFD
Current transformer
A-meter
V-meter
Change-over switch
Control button
Lamp
Others
Description, models, specs and quantity of main components
Switch fuses / load switch / ATS
T5 630.3Por 4P.FF
LNC3
#
#
#
When <400A, ES extended terminal is required.
Standard Unit Dimensions (W X H)
Description of main components
LNC2
#
#
#
T1-T2.3Por 4P.FEF
1
3
3
1
1
1
3
3
1
1
1
3
3
1
1
1
3
3
1
1
700X
800X
550
650
750
550
650
750
550
650
750
800A
Cabinet width=600 Cabinet width=700/800
Cabinet width=600 Cabinet width=700/800
Cabinet width=700/800
15
Electrical Solutions for Floor Mounted
Electrical Solutions
1QF21QF1M
应急供电电源 正常供电电源
柜宽=600
进线开关(<=63A DPT双电源开关)
500
DPT
DPT
650
柜宽=700/800
进线开关(<=160A DPT双电源开关)
DPT
DPT
柜宽=700/800
进线开关(<=250A DPT双电源开关)
Solution No. 02
Main Circuit Diagram
Auto transform switch
Purpose
400
Setup of components in Cabinet
Max.63A Max.160A Max.250A
#
#
#
1
2
3
4
5
6
7
8
9
10
11
12
600X
Breaker
Attachment
Incoming
Cabinet depth(mm)
Segregated
Maximum rated current(A)
Model & specs Qty. Model & specs Qty. Model & specs Qty. Model & specs Qty. Model & specs Qty.
Contactor
Thermal overload relays
Soft starter
VFD
Current transformer
A-meter
V-meter
Change-over switch
Control button
Lamp
Others
Description, models, specs and quantity of main components
#
#
#
Standard Unit Dimensions (W X H)
Description of main components
#
#
#
700X
800X
550
650
750
550
650
750
550
650
750
DPT63-CB011
DPT160-CB011
DPT250-CB011
Incoming switch(<=63A DPT solution)
Cabinet width=600
Incoming switch(<=160A DPT solution)
Incoming switch(<=250A DPT solution)
Cabinet width=700/800
Cabinet width=700/800
Switch fuses / load switch/ ATS
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info16
1QF21QF1M
应急供电电源 正常供电电源
柜宽=600
进线开关(<=63A DPT双电源开关)
500
DPT
DPT
650
柜宽=700/800
进线开关(<=160A DPT双电源开关)
DPT
DPT
柜宽=700/800
进线开关(<=250A DPT双电源开关)
Emergency power Normal power
600
700
800
Main Circuit DiagramMCCB Feed
Solution No. 03
Description, models, specs and quantity of main components
Standard Unit Dimensions (W X H)
Purpose
Cabinet depth(mm)
Setup of components in Cabinet
Maximum rated current Description of main components
1
Feed
400
160A
T1-T2,FF,3P
Centralized
Model & specs
Breaker
QF
110
0
175
550
825
14*T1,FF,3P
12*T1,FF,3P
550
550
275
110
0
825
825
21*T1,FF,3P
275
110
0
275
100
275
28*T1,FF,3P
175
100
18*T1,FF,3P 24*T1,FF,3P
275
275
175
275
100
275
275
10*T1,FF,3P 15*T1,FF,3P 20*T1,FF,3P
110
0
275
275
110
0
175
275
275
100
175
275
275
100
175
275
275
100
275
110
0
825
550
825
550
12*T2,FF,3P
825
18*T2,FF,3P
550
10*T2,FF,3P 15*T2,FF,3P
8*T2,FF,3P 12*T2,FF,3P
24*T2,FF,3P
20*T2,FF,3P
16*T2,FF,3P
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
Cabinet width=700
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
550
825
1100
550
825
1100
550
825
1100
550
825
1100
550
825
1100
550
825
1100
10*T1,FF,3P
15*T1,FF,3P
20*T1,FF,3P
8*T2,FF,3P
12*T2,FF,3P
16*T2,FF,3P
15*T1,FF,3P
18*T1,FF,3P
21*T1,FF,3P
12*T2,FF,3P
15*T2,FF,3P
18*T2,FF,3P
20*T1,FF,3P
24*T1,FF,3P
28*T1,FF,3P
16*T2,FF,3P
20*T2,FF,3P
24*T2,FF,3P
17Electrical Solutions
600
700
800
Main Circuit DiagramMCCB Feed
Solution No. 04
Description, models, specs and quantity of main components
Standard Unit Dimensions (W X H)
Purpose
Cabinet depth(mm)
Setup of components in Cabinet
Maximum rated current(A)
Description of main components
1
Feed
400
160A
T1-T2,FF,4P
Centralized
Model & specs
Breaker
QF
100
110
0
8*T1,FF,4P
10*T1,FF,4P
550
550
110
0
275
825
275
275
100
825
15*T1,FF,4P
12*T1,FF,4P
275
110
0
175
100
275
16*T1,FF,4P
175
275
20*T1,FF,4P
6*T1,FF,4P
550
825
9*T1,FF,4P
175
275
275
275
12*T1,FF,4P
110
0
100
110
0
100
110
0
275
275
275
175
100
275
275
175
275
825
550
10*T2,FF,4P
550
8*T2,FF,4P
825
15*T2,FF,4P
12*T2,FF,4P
20*T2,FF,4P
16*T2,FF,4P
275
275
175
275
550
6*T2,FF,4P
825
9*T2,FF,4P 12*T2,FF,4P
550
825
1100
550
8251100
550
825
1100
550
825
1100
550
825
1100
550
825
1100
6*T1,FF,4P
8*T1,FF,4P
10*T1,FF,4P
6*T2,FF,4P
8*T2,FF,4P10*T2,FF,4P
9*T1,FF,4P
12*T1,FF,4P
15*T1,FF,4P
9*T2,FF,4P
12*T2,FF,4P
15*T2,FF,4P
12*T1,FF,4P
16*T1,FF,4P
20*T1,FF,4P
12*T2,FF,4P
16*T2,FF,4P
20*T2,FF,4P
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
Cabinet width=700
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info18
600
700
800
10*T1,FF,3P
12*T1,FF,3P
14*T1,FF,3P
8*T2,FF,3P
10*T2,FF,3P
16*T2,FF,3P
15*T1,FF,3P
18*T1,FF,3P
21*T1,FF,3P
12*T2,FF,3P
15*T2,FF,3P
18*T2,FF,3P
20*T1,FF,3P
24*T1,FF,3P
28*T1,FF,3P
16*T2,FF,3P
20*T2,FF,3P
24*T2,FF,3P
Main Circuit DiagramMCCB Feed
Solution No. 05
Description, models, specs and quantity of main components
Standard Unit Dimensions (W X H)
Purpose
Cabinet depth(mm)
Setup of components in Cabinet
Maximum rated current
Description of main components
1
Feed
400
160A
T1-T2,FF,3P
Centralized
Model & specs
Breaker
Others
QF
650
975
325
130
0
650
14*T1,PF,3P
650
12*T1,PF,3P
130
0
325
125
975
325
130
0
975
21*T1,PF,3P
200
325
325
28*T1,PF,3P
125
325
18*T1,PF,3P 24*T1,PF,3P
200
325
325
125
325
10*T1,PF,3P 15*T1,PF,3P 20*T1,PF,3P
200
16*T2,PF,3P
20*T2,PF,3P
24*T2,PF,3P
650
975
325
130
013
00
325
125
975
325
130
0
650
975
12*T2,PF,3P
200
325
325
18*T2,PF,3P
125
325
10*T2,PF,3P
650
15*T2,PF,3P
200
325
325
125
325
12*T2,PF,3P8*T2,PF,3P
200
650
975
1300
650
975
1300
650
975
1300
650
975
1300
650
975
1300
650
975
1300
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
Cabinet width=700
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
19Electrical Solutions
600
700
800
Main Circuit DiagramMCCB Feed
Solution No. 05
Description, models, specs and quantity of main components
Standard Unit Dimensions (W X H)
Purpose
Cabinet depth(mm)
Setup of components in Cabinet
Maximum rated current Description of main components
1
Feed
400
160A
T1-T2,FF,4P
Centralized
Model & specs
Breaker
QF
125
130
012
5
130
0
650
625
10*T1,PF,3P
8*T1,PF,4P
130
0
975
325
125
325
325
200
130
0
975
15*T1,PF,3P
12*T1,PF,4P
325
20*T1,PF,3P
325
125
16*T1,PF,4P
200
325
650
975
325
130
0
125
325
325
200
650
975
10*T2,PF,4P
8*T2,PF,4P
325
130
0
15*T2,PF,4P
325
125
12*T2,PF,4P
200
325
650
6*T1,PF,4P
975
9*T1,PF,4P
325
325
325
12*T1,PF,4P
200
650
975
6*T2,PF,4P
325
325
325
9*T2,PF,4P
200
16*T2,PF,4P
20*T2,PF,4P
12*T2,PF,4P
650
975
1300
650
975
1300
650
975
1300
650
975
1300
650
975
1300
650
975
1300
6*T1,FF,3P
8*T1,FF,3P
10*T1,FF,3P
6*T2,FF,3P
8*T2,FF,3P
10*T2,FF,3P
9*T1,FF,3P
12*T1,FF,3P
15*T1,FF,3P
9*T2,FF,3P
12*T2,FF,3P
15*T2,FF,3P
12*T1,FF,3P
16*T1,FF,3P
20*T1,FF,3P
12*T2,FF,3P
20*T2,FF,3P
24*T2,FF,3P
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
Cabinet width=700
Cabinet width=600
Cabinet width=600
Cabinet width=600
Cabinet width=700
Cabinet width=700
Cabinet width=700
Cabinet width=800
Cabinet width=800
Cabinet width=800
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info20
600
700
800
21*Module(1*row)
42*Module(2*row)
63*Module(3*row)
84*Module(4*row)
105*Module(5*row)
27*Module(1*row)
54*Module(2*row)
81*Module(3*row)
108*Module(4*row)
135*Module(5*row)
33*Module(1*row)
66*Module(2*row)
99*Module(3*row)
132*Module(4*row)
165*Module(5*row)
Main Circuit DiagramMCCB Feed
Solution No. 05
Description, models, specs and quantity of main components
Standard Unit Dimensions (W X H)
Purpose
Cabinet depth(mm)
Setup of components in Cabinet
Maximum rated current
Description of main components
1
Feed
400
63A
200 series
Centralized
Model & specs
Miniature breaker
Miniature adjustable breaker
QF 150
1050
200
200
100
200
200
105*Module21*Module per row
165*Module33*Module per row
27*Module per row135*Module
250
470
650
850
1050
250
450
650
850
1050
250
450
650
850
1050
Cabinet width=600
Cabinet width=700
Cabinet width=800
21Electrical Solutions
600
700
800
500
700
900
1100
500
700
900
1100
500
700
900
1100
2-way
4-way
6-way
7-way
3-way
5-way
7-way
9-way
4-way
8-way
11-way
14-way
Main Circuit DiagramMCCB Motor Starting Circuit (Direct Starting)
Solution No. 05
Description, models, specs and quantity of main components
Standard Unit Dimensions (W X H)
Purpose
Cabinet depth(mm)
Setup of components in Cabinet
Maximum rated current
Description of main components
1
Feed
400
63A(0.37-30KW)
200 series
A9~A63
TA25,TA42,TA75
Centralized
Model & specs
Miniature breaker
2 Isolating switch
3 Contactor
4 Thermal overload relays
5 Others
Miniature adjustable breaker
QF
KH
KM
Max. 9*Motor Module
Max. 7*Motor Module
150
110
0
60
Max. 11*Motor Module
Cabinet width=600
Cabinet width=700
Cabinet width=800
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info22
Wall Mounted
Note:1.The upper and lower flanges are removable. An opening can be drilled onsite as needed. 2.The maximum opening should not exceed the existing opening on the enclosure. It’s recommended that the enclosure be fixed on the wall using four M8 expansion anchor bolts. 3.Cabinet width (options: 400, 500, 600 and 700mm); Cabinet height (options: 300, 600, 700, 800 and 900mm); Cabinet depth (options: 150 and 200mm). 4.When D=150mm, A=70mm; when D>150mm, A=100mm.
Fixed holes for expansion anchor bolts
Bottom/top plate opening
Wall
Expansion anchor bolts
—Installation Guide
23Installation Guide
Wall
Embedded depth: Enclosure depth minus 23mm
Bottom/top plate opening
Wall Embedded
Note:1.The upper and lower flanges are removable and know-down holes can be provided. An opening can be drilled onsite as needed. The maximum opening should not exceed the existing opening on the enclosure. 2.Cabinet width (options: 400, 500, 600 and 700mm); Cabinet height (options: 300, 600, 700, 800 and 900mm); Cabinet depth (options: 150 and 200mm). 3.The wall should have an opening where the enclosure can fit in. After fitting in, the gaps around should be filled up to keep the enclosure in place. 4.When D=150mm, A=70mm; when D>150mm, A=100mm.
24 MNS® Low Voltage Distribution Board and Power Cabinet Technical Info
Outer door panel Inner door panel Side view
Bottom plate
Floor mounted
Note:1.The cable chute opening on the foundation pedestal should preferably be as large as the bottom plate opening. 2.The dimensions of the cable bridge on top of the Cabinet should preferably be smaller than or equal to the dimensions of the top plate opening. 3.The Cabinet should preferably be fixed in place using four M12 expansion anchor bolts. 4.Cabinet width (options: 600, 700 and 800 mm); Cabinet height (options: 1700, 1800, 2000 and 2200mm); Cabinet depth (standard: 400mm).
25Installation Guide
Board and Cabinet installation requirements
Alignment and positioning
Install the board and Cabinet
Wire the board and Cabinet
Check wiring and perform insulation shaking test
Wall mounted
Install expansion anchor bolts
Wall embedded
Leave an opening on the wall
Floor mounted
Make cement table
MNS® Low Voltage Distribution Board and Power Cabinet Technical Info26
Installation Site Requirements:1)The construction of the room where the board and Cabinet will be mounted should have been completed. The elevation, dimensions, structure and embedded pieces of the civil work should conform to design requirements. The doors and windows should be closed, the painting of the walls and the rooftop should have been completed, there should be no water leakage, and the flooring should have been completed, and the floor should be clean. 2)If the product is to be wall-mounted or wall-embedded, a mounted position should be reserved in the civil work, and plastering, guniting and painting should have been completed. 3)A complete set of construction drawings and equipment technical documents should be provided. Construction organizing and technical, quality, safety, and fire protection measures should be in place.
Equipment Unpacking and Inspection:1)The boxes containing the equipment should be opened for inspection by the installer in the presence of the vendor, builder, and supervisory institute. The inspection should be documented. 2)Check the quantity of equipment against the design drawings, equipment list and technical documents. Check the specifications and models of the equipment and its attachments and spare parts against the packing list. They should conform to the requirements of the design drawings. The product quality certificate, the user’s manual and other documents should be in order. 3)Perform a visual inspection of the panel and Cabinet. The enclosure must be free of signs of damage or deformation, and the painting should be complete, free of scratches, and uniform. Check the insides of the panel and Cabinet. The electrical devices and components and insulation must be in order, firmly fixed, and free of signs of damage. And there should be no missing parts.
Installation Flowchart
Chemical and Petrochemicals-Dow Chemicals -BP -DuPont -Bayer (Shanghai) Polymer -CNOOC & Shell Nanhai Petrochemicals -Shell Changbai Gas Field -Shanghai SECCO Petrochemicals -Sinopec Shijiazhuang–Taiyuan Oil Pipeline -Nanjing Hercules -Yangzi Petrochemicals -Fujian Petrochemicals-Hainan Shihua Refinery -Baoji Oil Drilling Platform -Liaohe Petrochemicals -Sateri Jiangxi Chemical Fibers-Dushanzi Ethylene -Ningxia Oil Refinery-Shanxi Liulin Coal-Central Iraq Oil Refinery -Sudan FULA Oil Gas -Saudi Yanbu Petrochemicals-Guangzhou Petrochemical A6GB ProjectPower Plant -Sanmen Nuclear Power -Haiyang Nuclear Power Plant-Qinshan Nuclear Power Phase II -Gansu Jingyuan Power Plant -Jiangxi Electric Power Dispatching Center -Vietnam Cam Pha Power Plant -Vietnam Qingfeng Waste Heat Power Generation Project-Dalian Yanshui Substation -Fuchun River Hydroelectric Plant -GuizhouWujiangdu Power Plant -Hunan Zhexi Hydropower Station -Hunan Wanmibo Hydropower Station-Vietnam Jiaxing Power Plant-XichangXixi River Joint Replenishment Power Station-Vestas Wind Power -Thailand Capital Cogeneration PlantMetals & Mining -Mongolia Gold Mine
-Heihe Luoke Dong’an Gold Mine -Guizhou Jinfeng Gold Mine-Kazakhstan Copper Mine-Western Mining Co., Ltd. - Kaldor Furnace -Kunming Iron & Steel Plant -Shanghai Baosteel-Taiyuan Stainless Steel -Turky Steel Plant -Pingguo Aluminum Power Plant -Xiashun Aluminum Foils -Zhongzhou Aluminum -Bulgaria Cement Project-Saudi Ma’aden ProjectShipping & Ports-Guangzhou Nansha Port -Shenzhen Luohu Port -Baosteel Majishan PortTransport-Shaanxi-Beijing Line 2 Yulin Gas Compressor Station -Jiangyin Yangtze River Bridge -Shenzhen Metro -Shenzhen Airport -Hangzhou West Lake Tunnel-Ji’nan Electric Power TunnelManufacturing-Shanghai Bekaert Special Steel Curtains & Cords -Shanghai Port Machinery Heavy Industry -Boeing Tianjin -Pan-Pacific Automotive Technology (Dalian) -Suzhou BOSCH -Changzhou Hengli High-pressure -Cylinder Wujin New Factory -Changqing Electrical -Fuyao Glass-TEDA Blades Phase III-GITI Putian-Fujian LongyanSande Cement -Moroccan Cement -Saudi Cement -Belarusian Cement -Kerychef CementPulp&Paper-Nanning Phoenix Paper -Sun Paper -Zhenjiang Jindong Paper -Dagang APP Paper
-Kunshan Banknote Paper -Chenming (Hanyang) Paper -Nine Dragons PaperTobacco-Shanghai Cigarette Factory -Shenzhen Cigarette Factory -Tianjin Cigarette Factory -Xiamen Cigarette Factory -Kunming Cigarette Factory -Changde Cigarette Factory Water Treatment-Taiyuan City Water Supply -Zhangjiagang No. 4 Waterworks -Tianjin Jieyuan Waterworks -Guilin Waterworks-Guilin Dongjiang Waterworks-Guilin Chengbei Waterworks-Guangxi Langdong Boosting -Station Lingtie Waterworks -Xiaohongmen Sewage Treatment Plant -Wenzhou Shan Creek Hydro Project -Dagang Oilfield Group Sewage Treatment -Xiamen Wastewater Treatment Plant -Huangshi Drainage Company Pumping Station -Wayao Waterworks-Mauritius Sewage Treatment PlantData Centers-Fujian Nanping Mobile -Kunming Mobile-Shandong Jining Mobile -Shanghai Mobile World Expo Information Pavilion -Weihai Mobile-Yantai Mobile -East China Sea Telecom-Fujian Sanming Telecom -Shenzhen Huawei Group Data Center -Nanjing Huawei Software Base -Xiamen Dell Computers-Lucent Qingdao-China Post Project-Hebei Langfang Range Information Port-Suzhou Pacific Insurance Building Project
-Pacific Insurance Chengdu Support Center-Beijing Television -Center Wutongshan TV Tower -Shanghai Wenguang Media -Shenzhen Media Transmission -Xiamen Media Digital TV -Xiamen Radio 203 -Bank of China Quanzhou Branch-International Bank Xiamen Branch -Xiamen ICBC Computing Center Electronic -Beijing Monocrystalline Silicon Plant -Shenzhen SEG Samsung -Shenzhen STS Microelectronics -Gore Electronics (Shenzhen) -Zhuhai East Photoelectron -Fujian CPT Display Technology -Fujian Huanguang Optoelectronics -Chengdu Zhukuang Electronics -Chunghwa Picture Tubes (Fuzhou) -Xianyang Rainbow ElectronicsMunicipal Facilities -Beijing Academy of Military Medical Science-Beijing Restaurant -Jiangnan Institute of Computing Research -Mozambique Consulate -Shanghai New International Expo Centre -Shenzhen Customs -Xiamen Customs -Xiamen Comprehensive Sanitation Treatment Plant -Xiamen Municipal Bureau of Land and Housing Management Commercial Building -Shanghai Chung Shing Commercial Centre -Xiamen Real Estate Building -Xiamen Lu Hai Hotel -Xiamen China Town Consumer Goods -Colgate -Kerry Oils & Grains (Qingdao) -Xiamen Springs Barley -Nutricia Qiqihar Dairy Factory -Sea Oil Industry (Fangcheng Port) -AstraZeneca
27
—Product Credentials
List of Users
Product Credentials
© Copyright 2017 ABB. All rights reserved.Due to the possible developments, the information specified in the catalogue may only be considered binding after confirmation by ABB. 1S
XH
9050
01C
020
4 0
3-20
18
ABB China CustomerContact Center
—
ABB Xiamen Low Voltage Equipment Co., Ltd.No.12-20, 3rd Chuang Xin Road, Torch Hi-Tech ZoneXiamen SEZ, Fujian, P.R.China, 361006TEL: +86 592 6038118
ABB China Customer Service Hot Line:TEL: 800-820-9696 / 400-820-9696Email: [email protected]
www.abb.com/mns