microsoft powerpoint - drive test manual
TRANSCRIPT
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 1/14
INTRODUCTION
Drive Test & Propagation Prediction software are the two methods that are used to check the
coverage area of a particular wireless system.
The purpose of Drive Testing (DT) is to test the cellular network in particular area to give the
real picture of the network’s performance on the field.
DT provides an accurate real world capture of the RF environment under a particular set of
network and environment conditions.
Drive Test Tools collect the information sent over air interface between the cell and the
mobile station.
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 2/14
Why Drive the network?
New Site Integration (SSV)
RF Tuning
Network Optimization
Network Benchmarking
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 3/14
DRIVE TEST OVERVIEW
Drive TestPlanning
Implementation
Optimization
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 4/14
DRIVE TEST TOOLS
HARDWARE SOFTWARE
Laptops
Scanner
Mobile Handsets
GPS
Dongle
JSDU
NEMO
TEMS
WINTCATCHER
QXDM
ACCUVER, etc.
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 5/14
CELL SITE BASIC
A Cell Site is a site used to create a transmitting and receiving point that can carry traffic in a
cellular network.
Cell Sites transmit & receive RF signal at a particular band & frequency.
Depending on location & traffic load, there can 1,2 or more number of frequencies/carriers
per site.
1C– 1st Carrier Eg: 5780 for WABA market
• 2C– 2nd Carrier Eg: 925 for WABA market
Each site has a Site ID which is unique.
• Examples: MDL00334, DVL02665
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 6/14
RF PARAMETERS RSRP• Received Signal Reference Power
• To measure coverage• Excellent: RSRP ≥ -80dBm
• Average: -90dBm ≤ RSRP < -80dBm
• Poor: -100dBm ≤ RSRP < -90dBm
• Very Poor: RSRP < -100dBm
CINR• Carrier to Interference + Noise Ratio
• To measure channel quality
PCI
• Physical Cell Identifier
• Sectors of a cell site are distinguished with PCI
•
Example: For the site MDL00334, Alpha - PCI 222, Beta – PCI 223 & Gamma - PCI 224
EARFCN
• Evolved Absolute Radio Frequency Channel Number
• It reflects the center frequency of an LTE carrier ( for example 1.4/3/5/10/15/20 MHz carriers) but not take into accountchannel bandwidth
Alpha
BetaGamma
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 7/14
DRIVE TEST TYPES
SSV• Single Site Verification
Cluster Drive
• 2 or more sites
IFHO
• Inter Frequency Hand Over
• Frequency hand over from one site to another site with different frequency
• Example: 2C to 1C
IRAT• Inter Radio Access Technology Hand Over
• Technology hand over from LTE to 3G, 3G to 2G.
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 8/14
SSV
• SSV is performed for a single site:
• To verify coverage of a newly installed site.
• To verify several RF parameters like coverage, channel quality, interference, overshooting,
swapped sectors, etc. after a new site installation.
• To ensure there are no faults related to site installation or parameters setting.
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 9/14
SSV TEST SCOPE
To confirm the carrier frequency in use
• Frequency/E-ARFCN Check
To identify base station in use
• Site Name Check
To identify the cell sectors in use
• PCI (Physical Cell Identity) Check
To measure cell site received signal
• RSRP – Signal Coverage in dBm
• RSRQ – Signal Quality in dB
• SINR/CINR/SNR – Channel Quality Measurement
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 10/14
Stationary Throughput Test
Try to select the spot near to the cell site where you have Line-of-Sight (LOS) to the cell tower.
Make sure mobiles are camping on correct PCI during stationary throughput test, not changing fromone PCI to another PCI.
Verify RSRP & CINR are good.
Verify the stationary throughput test meet the following requirement for 1C & 2C; If not find theother spot near to the site with Line-of-Sight.
• 1C ( 10 MHz Carrier)
• Downlink Throughput > = 30 mbps
•
Uplink Throughput >= 10 mbps
• 2C (5 MHz Carrier)
• Downlink Throughput > = 20 mbps
• Uplink Throughput >= 5 mbps
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 11/14
Good Stationary Throughput Test Spot
Stationary Throughput Test Spot for
Alpha PCI (222)
Stationary Throughput Test Spot for
Gamma PCI (224)
Stationary Throughput Test Spot for
Beta PCI (223)
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 12/14
DT GUIDELINE
PREPARATION
• Do not go to the field without a good preparation.
• Prepare the tools completeness such as maps, cars, sites data, know the area heading to.
CHECK TOOLS
• Check if all necessary accessories are working properly such as GPS, inverter, mobile phones, SIM cards, etc.
SUGGESTIONS
• Avoid to drive same route twice while collecting data.
• Beware of restricted area such as naval/military base, one way street, high traffic streets.
• Plan the routes such as where to start until finishing the route.
• Cooperate with driver.
• Pay attention of car speed.
• Create notes for special events and notify the coordinator.
• Make sure GPS is working properly; without GPS data, the collected data means nothing.
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 13/14
SSV STRATEGY
Try to start the drive from near to the cell site.
Verify all the sectors are transmitting properly with correct PCIs.
Make sure the correct band & frequency are being scanned in the scanner.
Make sure mobiles are locked on correct band & frequency.
Periodically check throughput for Downlink & Uplink.
Check RSRP values are good for the routes near cell site.
8/9/2019 Microsoft PowerPoint - Drive Test Manual
http://slidepdf.com/reader/full/microsoft-powerpoint-drive-test-manual 14/14
SSV FILENAME CONVENTION
Follow the following filename convention for WABA market when saving
the files:
1C
• WABA_UDF4_UDF7_700_10M_SSL1_ sitename _d_
2C
• WABA_UDF4_UDF7_1900_05M_SSL2_ sitename _d_