microsoft powerpoint - 04 oeb204610 enodeb lte v100r006 remote commissioning issue 1

eNodeB V100R005 Remote

Commissioning

1

www.huawei.com

Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved.

eNodeB Remote

Commissioning

Copyright © 2013 Huawei Technologies Co., Ltd. All rights reserved. Page1

Contents

1. Commissioning Overview 2

2. Remote Commissioning on the M2000 7


Commissioning

2


Introduction to Commissioning

� To ensure that the eNodeB operates normally after the installation

� Commissioning Modes:

a) Remote Commissioning with M2000

b) With USB disk and M2000

c) Local Commissioning with LMT

� Commissioning Scenarios:

a) Without a Security Gateway

b) With a Security Gateway

� Commissioning Prerequisites:

a) eNodeB hardware installed and ready

b) Transport Network ready (for Remote Commissioning with M2000)


Scenario Without A Security Gateway


Commissioning

3


Scenario With A Security Gateway


Remote Commissioning Mode

M2000 Server

M2000

Client

eNodeB

Remote Commissioning on the M2000


Commissioning

4


Contents

1. Commissioning Introduction

2. Remote Commissioning on the M2000


Procedure for Remote eNodeB Commissioning on the M2000


Commissioning

5


Prepare for Remote eNodeB Commissioning Without A Security Gw

Page8

Prepare for the remote eNodeB commissioning


Prepare for Remote eNodeB Commissioning With Security Gw

Page9



Commissioning

6


Obtain eNodeB Information and Tools

Item Source or Remarks

eNodeB name

Planned by the operator.

eNodeB ID Planned by the operator.

eNodeB ESN

ESN identifies an NE uniquely. During network deployment, the installation engineer reports the mapping relation between the location of each site and the ESN to the staff at the maintenance center. Before delivery, the ESN is attached to the BBU of the eNodeB, as shown in the Figure



Obtain eNodeB Information and Tools (2)� Related files for eNodeB commissioning

� eNodeB software package

� eNodeB data configuration file

� Deployment list file

� eNodeB commissioning license

� Software of the remote electrical tilt (RET) antenna (Optional)

� Data configuration file of the RET antenna (Optional)

� Commissioning data template for the RET antenna (Optional)

� Tower-mounted amplifier (TMA) software (Optional)

Page11



Commissioning

7


Obtain eNodeB Information and Tools (3)� Related files for eNodeB commissioning

� eNodeB software package

� eNodeB data configuration file

� Deployment list file

� eNodeB commissioning license

� Software of the remote electrical tilt (RET) antenna (Optional)

� Data configuration file of the RET antenna (Optional)

� Commissioning data template for the RET antenna (Optional)

� Tower-mounted amplifier (TMA) software (Optional)

Page12



Prepare eNodeB Deployment List

Page13

� Deployment lists are exported from the CME

Export the eNodeB data configuration file and deployment list file from CME



Commissioning

8


Prepare eNodeB Deployment List (2)

Page14

Select target eNodeBs, the exported files include eNodeB deployment file and eNodeB data configuration files



Upload Data and Files

� Procedure

� Choose Configuration > Auto Deployment > eNodeB Auto

Deployment from the main menu of the M2000 client

� Click Prepare File&Data. The window for preparing files and

data is displayed. Upload data files as required

Page15



Commissioning

9


Upload Data and Files (2)

On the Software & Cold Patch tab page, choose Transfer > From

OSS Client to OSS Server. The NE File Transfer dialog box is

displayed.

Choose file

Upload in batches

Upload 1x1

Choose NE Type and File Type



Obtain the Digital Certificate

� A Digital Certificate allows the eNodeB and the security GW

to identify each other.

� Procedure

� Step1: Obtain the digital certificate required for the eNodeB

� Step2: Obtain the digital certificate required for the security

GW. Ensure that Huawei root CA certificate and Huawei CRL

file are configured on the security GW

Page17



Commissioning

10


Configure the Security Equipment

� Procedure

� Check the configuration of the security GW

� Configure the public DHCP server based on the customized

information in the context information

� Configure the authentication access equipment

� Configure the eNodeB CA certificate for the AAA server

Page18



Save The Files To USB Disk And Import Common Information Onsite� When the security GW is deployed in the network, and the

customized parameters cannot be configured to eNodeB by

using public DHCP server , you must import the common

configuration information to the eNodeB using a USB Disk.

Page19


UMPT LMPT


Commissioning

11




Create eNodeB Commissioning Task

Page21

Select deployment lists from the dropdown list

Browse for deployment lists in the Client

or

Create an eNodeB commissioning task


Commissioning

12


Create eNodeB Commissioning Task (2)

Page22

Modify data in the imported deployment lists as required

Create an eNodeB commissioning task


Start eNodeB Commissioning Tasks

Page23

Select steps in the

Select column based on the actual plan

Start the eNodeB commissioning task


Commissioning

13


Monitor eNodeB Commissioning Tasks

Page24

Monitor the eNodeB commissioning task


� After importing EDS data to M2000, records will be created in eNodeB Auto Development panel.

� One line for one eNodeB

� Current Step : show the steps of commissioning� Request ESN: show the reported ESN from eNodeB.

Page25

Status of eNodeB could be monitored here

Reported ESN list by DHCP function

Monitor eNodeB Commissioning Tasks (2)



Commissioning

14


BindEsn and Allocate IP addressPurpose: allocate OM related IP address to eNodeB by DHCP

function� After importing EDS data to M2000, records will be created in DHCP

Configuration Management panel.

� If the eNodeB has been powered on , eNodeB will broadcast DHCP DISCOVER .

� If the transmission is OK, and the DHCP relay function has been enabled on transmission device, M2000 will receive the DHCP DISCOVER message as following.

� Correspondingly, on eNodeB Auto Development panel, the ESN number carried by DHCP DISCOVER will be shown as following:

Page26



BindEsn and Allocate IP address (Cont.)

Page27

Bind the ESN: by choosing the right ESN for the eNodeB

Allocate IP address: M2000 will allocate IP address for the eNodeB automatically with these 4 messages.



Commissioning

15


DownloadSoftware: M2000 will compare eNodeB current version with the

target version. � If not the target version , download it from M20000;� If the target version, skip this step;

DownloadData: M2000 will download the M2000.xml file to eNodeB;

Activate: M2000 will activate the software version and the configuration file.

At the end , eNodeB will be reset. � If not choose the step, site will not be reset.

You can monitor every eNodeB’s status by the Current Step and Current Step

Progress:

Page28

Download Software/DataMonitor the eNodeB commissioning task


Manually Intervene eNodeB

Commissioning

� If eNodeB commissioning tasks are in the Waiting for

manual operation state, right-click the tasks, and then

choose Manual Confirm from the shortcut menu. The

Confirm dialog box is displayed, asking you whether to

proceed with the commissioning.

� Continue: Click Yes. The eNodeB commissioning tasks switch

to the Running state.

� Stop: Click No. The eNodeB commissioning tasks are still in

the Waiting for manual operation state.

Page29



Commissioning

16


Manage eNodeB Commissioning Task

� Once commissioning task is created, we can manage it by

the following methods

� Cancel the eNodeB Commissioning Progress, The tasks return

to the Waiting for start state.

� Pause/Resume the eNodeB Commissioning Task

� Restart/Delete the eNodeB Commissioning Task

Page30



Confirm eNodeB Commissioning

Completion

� After eNodeB passes service verification, the status of the

eNodeB commissioning tasks changes to Waiting for

acknowledgement. You need to manually confirm the

completion.

� In the commissioning task list, select one or multiple

commissioning tasks for confirming the completion. Right-

click the tasks, and then choose Acknowledge Completion

from the shortcut menu to confirm the completion.

Page31

Confirm eNodeB commissioning

completion


Commissioning

17


Handle eNodeB Commissioning Report

Page32

Handle the eNodeB Commissioning Report


Handle eNodeB Commissioning Report

(2)

� The eNodeB health can be decided on the basis of the

health check report in the eNodeB commissioning report

� Procedure

� Open the eNodeB commissioning report and view the health

check report. Learn the running status of the eNodeB

� If the result of the eNodeB health check fails, check for active

alarms and rectify the related faults by referring to the eNodeB

Alarm Reference

Page33



Commissioning

18


Handle eNodeB Commissioning Report (3)



Commission the Antenna System

� You can commission the RET antenna using the GUI or

man-machine language (MML) commands on the M2000.

� If you commission the RET antenna using the GUI on the

M2000, you can update the RET software, download the

RET configuration file, and set the RET tilt as required when

starting a commissioning task.

Page35



Commissioning

19


Commission the Antenna System (2)� You can commission the RET antenna using the GUI or

man-machine language (MML) commands on the M2000.

� If you commission the RET antenna using the GUI on the

M2000, you can update the RET software, download the

RET configuration file, and set the RET tilt as required when

starting a commissioning task.

Page36



Commission the Antenna System (3)� You can check whether the active TMA software version is

the same as the target software version by commissioning

the tower-mounted amplifier (TMA).

� If the two software versions are different, load the target

TMA software. After the TMA software is loaded, the TMA is

automatically reset. The software takes effect after the TMA

is reset.

Page37



Commissioning

20


Commission the Antenna System (4)� You can check whether the active TMA software version is

the same as the target software version by commissioning

the tower-mounted amplifier (TMA).

� If the two software versions are different, load the target

TMA software. After the TMA software is loaded, the TMA is

automatically reset. The software takes effect after the TMA

is reset.

Page38




(5)� Run the LST RRU command to query the Voltage Standing

Wave Ratio (VSWR) alarm threshold

� Run DSP VSWR to query the current VSWR of the antenna

� Run the STR VSWRTEST command to start the VSWR test

Page39

If Then

The test value is smaller than the VSWR alarm threshold

The antenna system is properly installed, end the commissioning

The test value is equal to or

greater than the VSWR alarm threshold

The antenna system is not properly

installed. Rectify the faults by referring to the handling procedures for the VSWR alarm in the eNodeB Alarm

Reference



Commissioning

21


Commission the Environment Monitoring

Equipment

Page40

Commission environment monitoring

equipment



Equipment

Page41


equipment


Commissioning

22



Equipment (3)

� After the parameters of the environment alarms are set, you

need to verify the parameter configuration by checking for

the external environment alarms.

� Manually trigger an external environment alarm. If the alarm

can be reported normally, the configuration of the external

environment alarm is correct.

Page42


equipment


Set the Maximum TX Power of RRU/RFU

� Run the DSP RRU command to query the cabinet number,

subrack number, slot number, transmit channel number,

and maximum output power of the RRU or RFU

� Run the LOC RRUTC command to set the maximum output

power of the RRU or RFU

� Run the RST BRD command to reset the RRU or RFU

� Run the DSP TXBRANCH command to check that the

maximum output power of each RRU or RFU is set

successfully

Page43

Set the maximum TX power of RRU/RFU


Commissioning

23


Replace Digital Certificate in IPSec

Scenario

� Upon deployment, the eNodeB uses the preset digital

certificate (prepared before delivery) as its identity certificate

to access the network.

� If an operator configures a Certificate Authority (CA) server,

the eNodeB obtains a digital certificate from the CA server

using the M2000 after connecting to the operator's network.

� The obtained digital certificate replaces the factory digital

certificate.

Page44


Scenario



Scenario

� Upon deployment, the eNodeB uses the preset digital

certificate (prepared before delivery) as its identity certificate

to access the network.

� If an operator configures a Certificate Authority (CA) server,

the eNodeB obtains a digital certificate from the CA server

using the M2000 after connecting to the operator's network.

� The obtained digital certificate replaces the factory digital

certificate.

Page45


Scenario


Commissioning

24


Compare license file and

configuration data

Page46

Compare the license file and configuration data


Verify eNodeB Basic Services

� Test the web page browsing service

� Test the file uploading service

� Test the file downloading service

� Test the VoIP services

Verify eNodeB Basic Services


Commissioning

25


Set eNodeB Maintenance Mode

Page48

Set Maintenance Mode

Query LTE Maintenance Mode

Set the eNodeB Maintenance Mode


Summary

� eNodeB commissioning Modes

� Commissioning Preparations

� The procedure of remote commissioning on the M2000


Commissioning

26


Thank youwww.huawei.com

microsoft powerpoint - 04 oeb204610 enodeb lte v100r006 remote commissioning issue 1

Documents

commissioning overview

commissioning introduction2

enodeb hardware

enodeb id

enodeb esnesn

huawei technologies

m2000c local commissioning

lmt commissioning scenarios