microkorg - user's manual-e

8/12/2019 MicroKorg - User's Manual-E

1/5

microKORG SoundEditor Users Manual 2005 KORG Inc.

microKORG SoundEditor for Mac OS X

The microKORG SoundEditor is a software program that allows you to use your computer to edit the various parameters of the microKORG. As youedit, the data is immediately transmitted to the microKORG so you can instantly hear the results of your editing. The computer can graphicallydisplay many parameters at one time, making it easy to address all the power of the microKORGs engine. The edited data can be saved in to a fileand stored. In this way, the microKORG SoundEditor can be also be used as a librarian for your sounds and settings.

* In order to use the microKORG SoundEditor, you will need a separately sold MIDI interface and MIDI cables to connect the microKORG to the computer.* This software is for sole use of the customer for trial purposes only and not for copying or distribution. KORG Inc. or any of its affiliates will not be held liable for any

damage that may result in the use this software. KORG does NOT officially support this software.

* We appreciate your bug reports so that we can refine our software in future.E-Mail: [email protected] note this address is for unsupported software only, and no response would be provided to each mail.

Instal lation and s etup

Before using, the microKORG SoundEditor application should be setup properly. Install appropriate MIDI interface drivers if they are not installed yet.

Setup

Setup procedure Handshake

Check this box if you want to confirm the received status of themicroKORG when it received the data. If the microKORG cantreceive the data (maybe Write Protected), the error dialog willbe displayed. When you use the microKORG SoundEditorwithout connecting the microKORG, please dont check thisbox.

1. Start up the microKORG SoundEditor.

2. Select Preference from the Application menu to makesettings for the microKORG SoundEditor.

MIDI In

Select the MIDI-In port your microKORG is connected to.

MIDI Out

Select the MIDI-Out port your microKORG is connected to.

Kill ZoomWindow Animation

Check this if you want to disable the zooming frame animationwhen you open or close windows.Default MIDI Channel

Set it to the MIDI Channel of your microKORG.3. When you finished the change, click the [Apply] button.

Send Parameter Change / Auto Update 4. On your microKORG, enable System Exclusive Message inthe MIDI Filter settings, and set the Write Protect to Off.Check this box if you want to send the modified value to the

microKORG every time you edit a parameter, updating thesound immediately.

1
mailto:[email protected]:[email protected]


2/5


Operat ion

Bank Window

All the items in one bank window are saved as one file. A bank window can hold multiple Program banks and Global banks. Each Program bankholds 128 Program data, and each Global bank holds a single set of Global settings. The left column shows the MIDI channel. Double-click the namefield in the Type column to change the bank name.

Loading sound data from the microKORG

1. Select New from the File menu, and a new bank window(Untitled-0) will appear. This bank window has one Program

bank. To see all Program data in your microKORG, allProgram data should be transmitted from your microKORG tothe SoundEditor.

2. Click the Program bank in the bank window to select (highlight)it. Select Receive Selected from the MIDI menu, and themicroKORG starts to transmit all Program data. When it iscompleted, a red check will appear at the top right of the bankwindow to indicate the window is modified.

3. The Global bank data can be received the same way. SelectAdd Global from the Edit menu to add a Global bank into thebank window. Click the Global bank in the bank window andselect Receive Selected from the MIDI menu. ThemicroKORG starts to transmit the Global data.

To open the bank data window

If you double-click the Program bank or the Global bank in the bankwindow, a Program list window or a Global window, respectively, willopen.

Program List Window

The microKORG has 128 Programs divided into two sides with 64 Programs each. The Program list window shows the Programs as A11 - A88 andB11 - B88 with space for the program names. If you double-click a Program in the Program list window, a Program (Overview) window will open.

Whenever you modify a parameter, the microKORG SoundEditor sends the updated program to the microKORG automatically allowing you to hearthe change, but the updated program hasnt been saved in the microKORGs memory yet. To keep programs in the microKORGs memory, selectTransmit or Transmit Selected from the MIDI menu to save the all program data in the bank into your microKORG when you finish all modifications.

Program name

Although the microKORG cannot save or create program names, themicroKORG SoundEditor can save a name with each program. You

can specify a program name in the Common edit window, as describedlater.

Cut & Copy / Paste

Click to select a program in the Program list window. The program willbe highlighted so that you can cut, copy or paste it from the Edit menu.

Exchange or move the program

You can exchange or move the selected program(s) by dragging it(them).

Transmit a program

To hear the selected program, you need to send it to your microKORG.Click the Transmit button at the top left of the Program list window. The

selected program will be sent to the internal edit buffer in yourmicroKORG, allowing you to hear it (it isnt saved though). This buttonis enabled when just one program is selected. You can send theselected program with the key combination of [option] + [return].

If the [caps lock] key of your computer is on, the program will be sentautomatically when you select it.

Receive a program

If you click the Receive button at the top left of the Program list window,microKORG sends the data currently in the internal edit buffer to theselected program in the Program list window. This button is enabledwhen just one program is selected.

View options

Click the check box at the top left of the Program list window to see apopup list containing several view options. Voice mode and Arpeggioparameters as well as a program name can optionally be shown in theprogram list.

2


3/5


Program (Overview) Window

If you double-click a program in the Program list window, the Program overview window will open. At this moment the program will be sent to themicroKORG, and when you modify a program parameter, the updated program is sent to microKORG automatically (if Send Parameter Change /

Auto Update is checked). The Program (Overview) window has six sections. In each section major parameters of the section are shown.Double-click the section you want to edit to open the edit window for the section. If Voice Mode is set to Single or Layer, Vocoder section cant beedited, and if Vocoder is selected, Timbre1/2 sections cant be edited. For description of each parameter, please refer to the microKORG UsersManual.

Transmit a program

If you click the Transmit button at the top left of the Program window,

current program will be sent to the internal edit buffer of themicroKORG (it isnt saved though).

Receive a program

If you click the Receive button at the top left of the Program window,current program in the internal edit buffer of the microKORG will beloaded.

Swap Timbre

When the Voice Mode is set to Layer, clicking the [Swap Timbre]button exchanges parameters between Timbre1 and Timbre2.

Common Edit Window

In this window you can edit the Program name and select the Voice Mode. Any modifications will be automatically sent to the microKORG(depending on the Preference setting).

Name

Enter a program name to be shown in the Program list and in the titlebar of each window. The microKORG itself cannot use or display this

program name, but it will memorize it. Initial preload data have noprogram name. There is a copy of the factory preload data includingnames in the microKORG SoundEditor folder.

A program name is up to a maximum of 12 characters.

Other window

If you click the [Other...] button (indicated by a green arrow), a popuplist will appear allowing you to access any other sections window.

Arpeggio Edit Window & Effect Edit Window

In these windows you can edit Arpeggio parameters and Effect parameters respectively. Any modifications will be automatically sent to themicroKORG (depending on the Preference setting).

Other window


Timbre1 / Timbre2 Edit Window

In this window you can edit Timbre parameters. Any modifications will be sent directly to the microKORG (depending on the Preference setting).

EG editing

You can also edit the Filter EG and the AMP EG by using the mouse todrag the squares that are located at the breakpoints in the EG graphic(The leftmost square cant be moved).

Other window


3


4/5


Vocoder Edit Window

In this window you can edit Vocoder parameters. Any modifications will be sent directly to the microKORG (depending on the Preference setting).

E.F. HOLD LEVEL

If you set the E.F. Sense value in the FILTER group to HOLD (=127),the microKORG keeps the characteristics of the input signal (Refer tothe microKORG Users manual for more details), which is reflected tothis E.F. HOLD LEVEL. For each of 16 filters, value can be set to0-7FFFFF(Hexadecimal). These values can be edited only if the E.F.Sense value is set to HOLD.

Other window


Global (Overview) Window

Global parameters are divided into three parts; Global, MIDI and Control Change Map.

Global, MIDI, Control Change Map

If you double-click on a part, an edit window for that part will open. Themodification made to the Global parameters is sent to the microKORGautomatically, and written immediately, unlike Program parameters.

Global Edit Window

In this window you can edit Global common parameters like Master Tune or Master Transpose. The modification is sent to the microKORG andsaved (written) automatically (depending on the Preference setting).

Other window

If you click the [Other...] button (indicated by a green arrow), a popuplist will appear allowing you to access the window of any other part.

MIDI Edit Window

In this window you can edit MIDI parameters such as MIDI Clock Source or MIDI Filter. The modification is sent to the microKORG and saved(written) automatically (depending on the Preference setting).

Other window


Control Change Map Edit Window

In this window you can edit the control change numbers assigned to the knobs and keys. The modification is sent to the microKORG and saved(written) automatically (depending on the Preference setting).

Each parameter name (knob name or key name) is the name for Singleor Layer mode (Synth Parameter). It is different from that of Vocodermode (Vocoder Parameter). Some parameters are not available in the

Vocoder mode. For more details, please refer to the microKORGUsers manual.

Other window


4


5/5


Other funct ion s

Keyboard Window

By selecting Keyboard form the MIDI menu, the Keyboard window will open and you can hear the sound by clicking the virtual keyboard in thiswindow using the mouse. Here you can also specify the MIDI Channel and Velocity.

[+][-] Button

You can select the octave with the [+] or [-] button at the top right ofthe virtual keyboard.

[Dmp] Button

By clicking the [Dmp] button at the bottom right of the virtual keyboard,you can select damper-on or damper-off.

[ ! ] ButtonYou can send an All Note Off message to the microKORG by clickingthe [!] button (next to the [Dmp] button) if for any reason hanging notesshould occur.

MIDI Monitor Window

By selecting Show MIDI Monitor from the MIDI menu, MIDI Monitor window will open. You can see the note message from the microKORG visually.The X (horizontal) axis represents the note number and the Y (vertical) axis indicates the velocity.

MIDI Channel

Selects the MIDI channel that will be monitored visually in this window.

Thru

If you check Thru, the microKORG SoundEditor sends any received

note messages to the microKORG.

Lock Velocity

When Thru is checked, the velocity of note messages sent to themicroKORG can be set to a fixed level (instead of the received notesown velocity) by checking Lock Velocity. The microKORGSoundEditor will send all note messages with this specified velocity.This option is available only when Thru is checked.

Menus

Application menu

Preference Set up optional settings.

Quit Quit the microKORG SoundEditor.

File menu

New Open a new bank window.

Open Open a previously saved bank window.

Close Close the currently selected window.

Save Save programs to disk.

Save As Save programs to disk under a new filename.

Save A Copy As Make a copy and save the copy to disk under a new filename.

Edit menu

Undo Cancel previous operation.

Cut Clear the selected parameter or program and place it on the clipboard.

Copy Copy the selected parameter or program to the clipboard.

Paste Paste the parameter or program that was previously copied to the clipboard.

Clear Erase the selected parameter or program (it will not be copied to the clipboard).

Select All Select all parameters in currently selected window.

Add Program Add a Program bank to the Bank window (available when the Bank window is selected).

Add Global Add a Global bank to the Bank window (available when the Bank window is selected).

Remove In the Bank window, remove the selected bank. In the Program list window, same as Clear.

Find In the Program list window, you can search for a program whose name includes the characters you enter here.

MIDI menu

Show/Hide MIDI Monitor Show or hide MIDI Monitor window.

Transmit Transmit all Program data (128 Programs) or Global data and save (write) in the microKORG.

Transmit Selected Transmit the selected bank data and save (write) in the microKORG.

Receive Receive all Program data (128 Programs) or Global data.

Receive Selected Receive data into the currently selected bank.

All Note Off Turn off all notes should any hanging notes occur.

Keyboard Open the Keyboard window.

5

microkorg - user's manual-e

Documents