meters - dbelec.netfor higher ranges than 5a, use external shunt with a 50mv(60mv) instrument. when...
TRANSCRIPT
38
40
42
44
46
48
47
50
51
52
54
56
Ampere Meter
Volt Meter
Watt Meter
Var. Meter
Outside Connection (Watt, PF, Var)
Receive Indicator Meter
Demand Meter
Meter Relay
Meter Dimensions
Meter Connection
Power Factor Meter
Frequency Meter
Meters
www.dbelec.net 37
D-800
D-200
The types of operating principle of ammeter are the rectifier type and the moving irontype, and the rectifier type ammeter has a merit of measuring small current valuecompared with moving iron type.
AC Ampere Meter
To deal with current exceeding 5A, use a 5A(1A) meter in combination with a C.T. A.C ammeter is used with a current transfomer externally mounted, and it is noted that primary current of a current transformer and a full scale of the meter are identical when used.If the circuit voltage exceeds 500V even when the current is less than 5A use a 5A(1A) meter in combination with a C.T to ensure insulation.The scale range of ammeter for motor circuit is extended up to 150%~500% of rated current,so that these are proteced from the impact of the starting current and ensured of long life.Am expanded scale has the normal maximum reading(upper limit of effective measurement range) at the app. 65% point on the scale, and the rest of it (65%~100%) is devoted toextension reading. (tolerance of extension area : 5%)
Features
50 A 30 A / 50mV / 200mV100 mA 30 A / 1A / 5A
30 mA 30 A / 1A / 5A
Meter rating (A.C) Meter rating (D.C)
38
Ampere Meter
D-80
The types of operating principle of ammeter are the moving coil type.
DC Ampere Meter
For higher ranges than 5A, use external shunt with a 50mV(60mV) instrument.When D.C ammeter is used with a shunt, it is noted that a full scale and a terminalvoltage(50mV, 60mV) of the ammeter are same as the rated primary current and secondary voltage of the shunt respectively.Use any leadwire of which resistance is less then 0.05 in total.If the shunt lead resistance is indefinite, the meters may be set up with a availableresistor(V.R) for sensitivity adjustment.The shunt should be connected to the negative side linc.
Features
Shape of case Type Rated Curr.
OperatingPrinc. Accur. (%) Freq. Burden (VA)
Rectangular (60 x 60mm) D-60
D-68
D-80
D-100
D-800
D-110
D-70
D-200
D-300
5A50, 60 mV
2.52.5
50~60 Hz1.0
50mV Drop
Rectangular (60 x 80mm)ACDC
ACDC
5A50, 60 mV
2.52.5
50~60 Hz1.0
50mV Drop
ACDC
5A50, 60 mV
2.52.5
50~60 Hz1.0
50mV Drop
Rectangular (100 x 83mm)ACDC
5A50, 60 mV
1.51.5
50~60 Hz1.0
50mV Drop
Rectangular (80 x 80mm) ACDC
5A50, 60 mV
1.51.5
50~60 Hz1.0
50mV Drop
Rectangular (110 x 110mm) ACDC
5A50, 60 mV
1.51.5
50~60 Hz1.0
50mV Drop
Rectangular (70 )ACDC
5A50, 60 mV
2.52.5
50~60 Hz1.0
50mV Drop
Rectangular (72 x 72mm)ACDC
5A50, 60 mV
1.51.5
50~60 Hz1.0
50mV Drop
Rectangular (98 x 98mm)ACDC
5A50, 60 mV
1.51.5
50~60 Hz1.0
50mV Drop
Rectangular (80 x 80mm)
www.dbelec.net 39
D-68
Volt Meter
The types of operating principle of voltmeter are the rectifier type(A.C), and movingiron type(A.C) the voltmeter is used with a potential transformer externally mountedin case of high voltage.
AC Volt Meter
For higher ranges than 300V, use potential transformer(P.T) with a 150V A.C voltmeter. But the voltmeter of 600V is able to supply by order of customer.When lettering the voltage ratio on voltmeter, the meters for 3phase 4wire are lettered as likeas the meters for 3phase 3wire. namely on 3phase 4wire in case of the indicating for line-to-line voltage by line-to- ground voltage, and line-to-line voltage by line-to-line voltage, he meters are not wited the 3Full scale of voltmeter when use the P.T, the standard calibration value of voltmeters are 150V and/or 300V but, the full scale of voltmeters are indicated the 30Kv, 9000V, 4500V and 600V etc.
Features
D-68
18 V 600 V / 110V
30 V 300 V / 220V
AC Volt Meter
50 mV 750 V
DC Volt Meter
/ 10V
D-200
40
The types of operating principle of voltmeter are the moving coil type.
DC Volt Meter
For higher ranges than 750V, use external multiplier or voltage-dividing multiplier with a 1mA instrument.The D.C voltmeter shuld be connected to the positive side line as connection diagram.The standard current consumption of these D.C voltmeter is 1mA. (1K /V).
Features
Shape of case TypeRated
VOLTSOperating
Princ.Accur. (%) Freq. Burden (VA)
Rectangular (60 x 60mm)
Rectangular (60 x 80mm)
Rectangular (80 x 80mm)
Rectangular (100 x 83mm)
Rectangular (80 x 80mm)
Rectangular (110 x 110mm)
Rectangular (70 )
Rectangular (72 x 72mm)
Rectangular (98 x 98mm)
D-60
D-68
D-80
D-100
D-800
D-110
D-70
D-200
D-300
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 5.0, 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
150, 300V1, 600V
50~60 Hz 0.51K /v
2.52.5
2.52.5
2.52.5
1.51.5
1.51.5
1.51.5
2.52.5
1.51.5
1.51.5
ACDC
ACDC
ACDC
ACDC
ACDC
ACDC
ACDC
ACDC
ACDC
D-80
D-800
www.dbelec.net 41
Operating voltage range is 10% of rated voltage.For other voltage and/or current ratings higher then listed on the spescification, use external current transformerand/or external potential transformer with a 110V/5A instrument, when ordering, specify the full scale valuedesired, P.T ratio and C.T ratio
Rating voltage of 3phase 4wire is at Phase voltage.(/ 3)When using P.T and C.T, calibrating watts will be as follows.
The standard calibration watt of the meter for single phase 2wire was calibrated the 600WThe standard calibration watt of the meter for single phase 3wire was calibrated the 1.0Kw as the meter for3phase 3 wire.The standard calibration the 1000W (1.0Kw) as the meter for 3phase 3wire.The standard calibration watt of the meter for 3phase 3wire was calibrated the 1.0KwThe standard calibration watt of the meter for 3phase 4wire was calibrated the 1.666Kw.The other 1) In case of 22900V
calibrating watt of 3phase 3wire : 0.961Kw calibrating watt of 3phase 4wire : 1.666Kw2) In case of 380V
3phase 3wire- use to potential transformer ratio 380/110V : 1.158Kw- not use to potential transformer : 4.0Kw
3phase 4wire- use to potential transformer ratio V : 2.0Kw
- not use to potential transformei: 4.0Kw
- not use to potential transformer at 3phase 4wire : 2.0KwWhen shall be catch the flow of current, be used the Watt meter.
Example (3phase 4wire)Full scale of wattmeter : 4000W
C.T ratio : 100/ 5A
=1.666KwThe instrument of D-W T Type is self contained with the Transducer Box.
380 190
3 3
22900 1903 3
4000W22900 190
3 3 ( / V) (100/5A)
V
Calibrating watts =
P.T ratio :
2083 V3) In case of
Full scale watts(P.C ratio) (C.T ratio)
calibrating watt =
The types of operating principle of these meters are the transducer type,these meters measure active power.Transducer is used with the transducer type attached inside or outside.
Features
110~380V 110~220V 1~5A
/
/
D-P111TU
42
Watt Meter
Shape of case Circuit Application Type
Rectangular
(80 x 80mm)
1P2W
1P3W
3P3W
3P4W
3P4W
D-W801
D-W802
D-W803
D-W804
D-W805
Rated Curr.
5 A
5 A
5 A
5 A
5 A
OperPrinc.
Accur.(%)
60
60
60
60
60
Freq.(Hz)
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Unbalance
Unbalance
Unbalance
Balance
Balance
Unbalance
Curr. Volt. Curr. Volt.
Burden RemarkRated Volt.
110, 220 V
110 V
110, 220 V
190/ 3 , 380/ 3
190/ 3 , 380/ 3
Rectangular
(110 x 110mm)
1P2W
1P3W
3P3W
3P4W
3P4W
D-W111T
D-W112T
D-W113T
D-W114T
D-W115T
5 A
5 A
5 A
5 A
5 A
60
60
60
60
60
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Unbalance
Unbalance
Unbalance
Balance
Balance
Unbalance
110, 220 V
110 V
110, 220 V
190/ 3 , 380/ 3
190/ 3 , 380/ 3
Stanard Full Scale Table (Watt meter)
Phase Wire
P.T ratio(V) 110
0.6KwC.T ratio
CalibratingWatts
1P2W
110
1.0Kw 2.0Kw 1.158Kw
1P3W
220380
110
3P3W 3P4W
5 / 5
10 / 5
15 / 5
20 / 5
25 / 5
30 / 5
40 / 5
50 / 5
60 / 5
75 / 5
80 / 5
100 / 5
120 / 5
150 / 5
200 / 5
250 / 5
300 / 5
400 / 5
500 / 5
600 / 5
750 / 5
800 / 5
1000 / 5
1200 / 5
1500 / 5
2000 / 5
2500 / 5
0.6
1.2
1.8
2.4
3.0
3.6
4.8
6.0
7.2
9.0
9.6
12.0
14.4
18.0
24.0
30.0
36.0
48.0
60.0
72.0
90.0
96.0
120.0
144.0
180.0
240.0
300.0
1
2
3
4
5
6
8
10
12
15
16
20
24
30
40
50
60
80
100
120
150
160
200
240
300
400
500
2
4
6
8
10
12
16
20
24
30
32
40
48
60
80
100
120
160
200
240
300
320
400
480
600
800
1000
4
8
12
16
20
24
32
40
48
60
64
80
96
120
160
200
240
320
400
480
600
640
800
960
1200
1600
2000
4
8
12
16
20
24
32
40
48
60
64
80
96
120
160
200
240
320
400
480
600
640
800
960
1200
1600
2000
30
60
90
120
150
180
240
300
360
450
480
600
720
900
1200
1500
1800
2400
3000
3600
4500
4800
6000
7200
9000
12MW
15
60
120
180
240
300
360
480
600
720
900
960
1200
1440
1800
2400
3000
3600
4800
6000
7200
9000
9600
12MW
14.4
18.0
24.0
30.0
200
400
600
800
1000
1200
1600
2000
2400
3000
3200
4000
4800
6000
8000
10MW
12
16
20
24
30
32
40
48
60
80
100
200
400
600
800
1000
1200
1600
2000
2400
3000
3200
4000
4800
6000
8000
10MW
12
16
20
24
30
32
40
48
60
80
100
2
4
6
8
10
12
16
20
24
30
32
40
48
60
80
100
120
160
200
240
300
320
400
480
600
800
1000
4
8
12
16
20
24
32
40
48
60
64
80
96
120
160
200
240
320
400
480
600
640
800
960
1200
1600
2000
4
8
12
16
20
24
32
40
48
60
64
80
96
120
160
200
240
320
400
480
600
640
800
960
1200
1600
2000
100
200
300
400
500
600
800
1000
1200
1500
1600
2000
2400
3000
4000
5000
6000
8000
10MW
12
15
16
20
24
30
40
50
200
400
600
800
1000
1200
1600
2000
2400
3000
3200
4000
4800
6000
8000
10MW
12
16
20
24
30
32
40
48
60
80
100
1400
2800
4200
5600
7000
8400
11.2MW
14.0
16.8
21.0
22.4
28.0
33.6
42.0
56.0
70.0
84.0
112
140
168
210
224
280
336
420
560
700
1.0Kw
440
110
1.0Kw
3300
110
1.0Kw
6600
110
1.0Kw
22000
110
0.961Kw
22900
110
1.0Kw
154Kv
110
2.0Kw
208/ 3
2.0Kw
380/ 3
190/ 3
1.666Kw 1.666Kw
11400/ 3
190/ 3
22900/ 3
190/ 3
4.0Kw
380
3
www.dbelec.net 43
The types of operating principle of these meters are the transducer type,these meters measure reactive power.Transducer is used with the transducer type attached inside or outside.
Operating voltage range is 10% of rated voltage.For other voltage and/or current ratings higher then listed on the specification, use external C.T and/or external P.T with a 110V/5A instrument, when ordering, specify the full scale valuedesired, P.T ratio and C.T ratio.
Rating voltage of 3phase 4wire is at phase voltage.(/ 3 )The full scale of varmeter is generally 1/2, 1/3, or 1/4 of load capaciry.When using P.T and C.T, calibrating vars will be as follows
Namely 1) The standard calibration var of the meter for single phase 2wire : 300Var (0.3Kvar)2) Single phase 3wire : 500Var (0.5Kvar)3) 3phase 3wire : 500Var (0.5KVar)4) 3phase 4wire : 833Var (0.833Kvar)
The other 1) In case of 22900V- Calibrating var of 3phase 3wire : 480Var- Calibrating var of 3phase 4wire : 833Var2) In case of 380V- 3phase 3wire use to potential transformer ratio 380/110V : 579Var
not use to potential transformer : 2.0Kvar- 3phase 4wire use to potential transformer ratio
3) In case of 208 / 3Vno use to potential transformer at 3phase 4wire : 1.0Kvar
The standard scale is LAG. The varmeter with 0 point at center is recomended, if it is used instead of a power factormeter. In case of using the varmeter as a power factor meter, it is recommended, to use a leftside and of 0 point at the center as Lead-O-LAG.
The instrument of D-V T Type is self contained with the Transducer Box.
Features
110~380V 110~220V 2.5A, 5A
Full scale Vars(P.C ratio) (C.T ratio)
calibrating watt =
380 190
3 3V : 1.0Kvar
D-V114T
44
Var. Meter
Standard Full Scale Table (1/2 Var. meters)
Phase Wire
P.T ratio(V) 110
0.3KvarC.T ratio
CalibratingWatts
1P2W
110
0.5Kvar 1.0Kvar 0.579Kvar
1P3W
220380
110
3P 3W 3P 4W
5 / 5
10 / 5
15 / 5
20 / 5
25 / 5
30 / 5
40 / 5
50 / 5
60 / 5
75 / 5
80 / 5
100 / 5
120 / 5
150 / 5
200 / 5
250 / 5
300 / 5
400 / 5
500 / 5
600 / 5
750 / 5
800 / 5
1000 / 5
1200 / 5
1500 / 5
2000 / 5
2500 / 5
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3.0
6
4.5
4.8
6.0
7.2
9.0
12.0
15.0
18.0
24.0
30.0
36.0
45.0
48.0
60.0
72.0
90.0
120.0
150.0
0.5
1
1.5
2
2.5
3
4
5
6
7.5
8
10
12
15
20
25
30
40
50
60
75
80
100
120
150
20
250
1
2
3
4
5
6
8
10
12
15
16
20
24
30
40
50
60
80
100
120
150
160
200
240
300
400
500
2
4
6
8
10
12
16
20
24
30
32
40
48
60
80
100
120
160
200
240
300
320
800
480
600
800
1000
2
4
6
8
10
12
16
20
24
30
32
40
48
60
80
100
120
160
200
240
300
320
800
480
600
800
1000
15
30
45
60
75
90
120
150
180
225
240
300
360
450
600
750
900
1200
1500
1800
2250
2400
3000
3600
4500
6000
7500
30
60
90
120
150
180
240
300
360
450
480
600
720
900
1200
1500
1800
2400
3000
3600
4500
4800
6000
7200
9000
12Mvar
15
100
200
300
400
500
600
800
1000
1200
1500
1600
2000
2400
3000
4000
5000
6000
8000
10Mvar
12
15
16
20
24
30
40
50
100
200
300
400
500
600
800
1000
1200
1500
1600
2000
2400
3000
4000
5000
6000
8000
10Mvar
12
15
16
20
24
30
40
50
1
2
3
4
5
6
8
10
12
15
16
20
24
30
40
50
60
80
100
120
150
160
200
240
300
400
500
2
4
6
8
10
12
16
20
24
30
32
40
48
60
80
100
120
160
200
240
300
320
800
480
600
800
1000
2
4
6
8
10
12
16
20
24
30
32
40
48
60
80
100
120
160
200
240
300
320
800
480
600
800
1000
50
100
150
200
250
300
400
500
600
750
800
1000
1200
1500
2000
2500
3000
4000
5000
6000
7500
8000
10Mvar
12
15
20
25
100
200
300
400
500
600
800
1000
1200
1500
1600
2000
2400
3000
4000
5000
6000
8000
10Mvar
12
15
16
20
24
30
40
50
700
1400
2100
2800
3500
4200
5600
7000
8400
10.5Mvar
11.2
14.0
16.3
21.0
28.0
35.0
42.0
56.0
70
84
105
112
140
168
210
280
350
Shape of case Circuit Application Type
Rectangular
(80 x 80mm)
1P2W
1P3W
3P3W
3P4W
3P4W
D-V801
D-V802
D-V803
D-V804
D-V805
Rated Curr.
5 A
5 A
5 A
5 A
5 A
1.5
1.5
1.5
1.5
1.5
OperPrinc.
Accur.(%)
60
60
60
60
60
Freq.(Hz)
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Unbalance
Unbalance
Unbalance
Balance
Balance
Unbalance
Curr. Volt. Curr. Volt.
Burden RemarkRated Volt.
110, 220 V
110 V
110, 220 V
190/ 3 , 380/ 3
190/ 3 , 380/ 3
Rectangular
(110 x 110mm)
1P2W
1P3W
3P3W
3P4W
3P4W
D-V111T
D-V112T
D-V113T
D-V114T
D-V115T
5 A
5 A
5 A
5 A
5 A
1.5
1.5
1.5
1.5
1.5
60
60
60
60
60
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Unbalance
Unbalance
Unbalance
Balance
Balance
Unbalance
110, 220 V
110 V
110, 220 V
190/ 3 , 380/ 3
190/ 3 , 380/ 3
0.5Kvar
440
110
0.5Kvar
3300
110
0.5Kvar
6600
110
0.5Kvar
22000
110
0.480Kvar
22900
110
0.5Kvar
154Kv
110
1.0Kvar
208/ 3
1.0Kvar
380/ 3
190/ 3
0.833Kvar 0.833Kvar
11400/ 3
190/ 3
22900/ 3
190/ 3
2.0Kvar
380
3
www.dbelec.net 45
The types of operating principle of these meters are the transducer type and also the meter divide into the balanced power factor meter and theunbalanced power factor meter.
Operating voltage range : rated voltage 10%For other voltage and/or current ratings higher then listed in specification use external C.T and/or external P.T with a 110V/5A instrument.The instrument of D-P T Type is self contained with the Transducer Box.Rating voltage of 3phase 4wire is at phase voltage. (/ 3)The meter do not operate when load current is under 10% of rated current. And if the circuit current is less than a 1/3 of the ating (or less than 1.66A if the ratingis 5A) the error of P.F meter may have happened more than that of rated current.Standard scale : Lead 0.5~1.0~0.5Lag
Features
110~380V 110~220V 1~5A
Shape of case Circuit Application Type
Rectangular
(80 x 80mm)
1P2W
1P3W
3P3W
3P3W
3P4W
3P4W
D-P801
D-P802
D-P803
D-P803u
D-P804
D-P804u
Rated Curr.
5 A
5 A
5 A
5 A
5 A
5 A
OperPrinc.
Accur.(%)
60
60
60
60
60
60
Freq.(Hz)
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Balance
Unbalance
Balance
Unbalance
Curr. Volt.
BurdenRemarkRated Volt.
110, 220 V
110, 220 V
110, 220 V
110, 220 V
190/ 3 , 380/ 3
190/ 3 , 380/ 3
Rectangular
(110 x 110mm)
1P2W
1P3W
3P3W
3P3W
3P4W
3P4W
D-P111T
D-P112T
D-P113T
D-P113Tu
D-P114T
D-P114Tu
5 A
5 A
5 A
5 A
5 A
5 A
60
60
60
60
60
60
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Balance
Unbalance
Balance
Unbalance
110, 220 V
110, 220 V
110, 220 V
110, 220 V
190/ 3 , 380/ 3
190/ 3 , 380/ 3
D-P114TU
46
Power Factor Meter
The types of operating principle of these meters are the transducer type.And this meter is used for measuring the frequency of generator.
Usable voltage range. 110V rating : 80V to 120V, 220V rating : 160V to 240VThe standard scale range is the 45Hz to 55Hz, and/or 55Hz to 65Hz.For a rating voltage higher than 220V, use external potential transformer with a 110V instrument.
Features
Shape of case Type ofPointer Type Rated
Volt.OperPrinc.
Accur.(%)
Burden(VA)
Rectangular (80 x 80mm)
Rectangular (100 x 83mm)
Rectangular (80 x 80mm)
Rectangular (110 x 110mm)
Rectangular (70 )
Rectangular (72 x 72mm)
Rectangular (98 x 98mm)
110, 220V
D-80
D-100
D-800
D-110
D-70
D-200
D-300
1.0 2.0
Source Source
Load Load
External Potential Transformer
P.T
D-110
D-70
www.dbelec.net 47
Frequency Meter
Watt Meter & Var. Meter
1Phase 2WireWatt Meter & Var. Meter
1Phase 3WireWatt Meter & Var. Meter
3Phase 3WireWatt Meter & Var. Meter
3Phase 4WireWatt Meter & Var. Meter Voltage Balance
3Phase 4WireWatt Meter & Var. Meter Unbalance
With Ext. Transducer (D- Type) With Int. Transducer (D- T Type)
48
Outside Connection
Power Factor Meter
1Phase 2WirePower Factor Meter
1Phase 3WirePower Factor Meter
3Phase 3WirePower Factor Meter Balance type
3Phase 3WirePower Factor Meter Unbalance type
3Phase 4WirePower Factor Meter Balance type
3Phase 4WirePower Factor Meter Unbalance type
Ext. Transducer (D-P Type) Int. Transducer (D-P T Type)
www.dbelec.net 49
This option meter of operating principle are the rectifier type and the moving coil type.
Shape of case Type Operating Princ.
Accur.(%) Freq. Burden
(VA)
Rectangular (60 x 60mm)
Rectangular (60 x 68mm)
D-60
D-68
50~60Hz
D.C
0.5
1K /v
50~60Hz
D.C
0.5
1K /v
Rectangular (80 x 80mm) D-8050~60Hz
D.C
0.5
1K /v
Rectangular (100 x 83mm) D-10050~60Hz
D.C
0.5
1K /v
Rectangular (80 x 80mm) D-80050~60Hz
D.C
0.5
1K /v
Rectangular (110 x 110mm) D-11050~60Hz
D.C
0.5
1K /v
Rectangular (72 x 72mm) D-20050~60Hz
D.C
0.5
1K /v
Rectangular (98 x 98mm) D-30050~60Hz
D.C
0.5
1K /v
Rectangular (70 ) D-7050~60Hz
D.C
0.5
1K /v
D-110
D-100
AC 18~600V -
0~1mA
4~20mADC 1~600V
50
Receive Indicator
+ -
ExitReset
AuxPower
MeterInput
+ -Aux
PowerMeterInput
1 2
3 4
1 2
3 4
ExitReset
This meter of complex type of analogue and digital type has a peak for memory ofmaximum instaneous value of the transient voltage orcurrent during the shortcircuit or ground fault on the transmission and distribution lines.
1. Normal voltage and current will be indicated by an along needle and then the peakvalue will be indicated on digital FAD(3Digital).
2. Demand of peak value will be indicated as memory (3Digital) the max one at only of many peak values.
3. The rating of digital is same as analogue and full scale of is same as on analogue.4. The peak value always turns on in the digital display, it is reset the peak value by
pressing the button.(push S/W)5. When auxiliary power loss occurs, the peak value will be accumulated in S-RAM.
when auxiliary power returns, the peak value will be displayed in the digital display.6. If an external reset terminal is connected on push button S/W, at inpossible
to reset on outside.
Outside Connection Diagram
Name of meter Shape of case
Ground CurrentMeter
Ground VoltageMeter
Rectangular(110x110mm)
Rectangular(110x110mm)
Type
D-D111
D-D110
Rating
5 A
150, 250, 259V
Operating Princ.
Accur.(%)
1.5%
1.5%
Freq.
50Hz
or
60Hz
Burden
1VA
0.5VA
AuxPower
AC220
or
AC110
D-DW113T
Volt, Ampere, Hz, Meter Watt, Var, PF, Meter
Transducer
www.dbelec.net 51
Demand Meter
This meter relay of complex type of analogue and digital type is used for alarm ortrip of some circuit in accordance with setting the movement value and time ofMeter(7segment LED) which indicates low and high limitation on ampere meter,voltage, meter.
1. Read the instructions in this explanation because they furnish important indications about the setting value.
2. Auxiliary power : AC 110V(220V) / 60Hz. 3. Nomal voltage and current will be indicated by an along needle and on digital FND
(3Digital).
Caution
Meter Relay Current Meter
Meter Relay Voltage Meter
D-R111A
D-R111B
D-R111C
1A, 5 A
150, 250
300, 600V
D-R111C
Name of meter Shape ofcase
Rectangular(110x110mm)
Rectangular(110x110mm)
Type Rating Operating Princ.
Accur.(%)
1.5%
1.5%
Freq.
50Hz
or
60Hz
Burden
1VA
0.5VA
AuxPower
AC220
or
AC110D-R110A D-R110B D-R110C
Outside Connection Diagram
Ampere, Volt, Hz, Meter Watt, Var, PF, Meter
52
MR (Meter Relay)
1. The LED display meter input value. To confirm the setting value amanual working condition is obtained by pushing the button as follow.
Other displays except input value return to the lnput mode after 6 secs.
How to adjust push S/W (see the picture No. ~ )
2. Operating value and operating time setting by pressing thebutton no and for 3secs at the same time, the setting mode will be entered the LED flashes then press
the button no to change the flashing value of the display anduse the button no to increase the count of it. After setting the input value, press the button no and for 3secs at the sametime to save the value of selection. (Display will be shown as below)
3. Meter Relay Operating This meter is able to set the time 0 to 99 seconds. If the input value is lower than low setting value or higher thanhigh setting value, the relay contacts are operated after presetting time.(During presetting time the LED or flashes, then afterpresetting time the LED is lightened and its replay is operated)When the auxiliary power is connected the initial time, low relaywill not operate without an input value which is higher than thelow setting value at first.(lt is to poeventing the operating therelay without input value at the initial)For turning off low relay operating set 0 to the low setting value.High setting value should be set higher than the input maximum value of meter to be off the high relay operating.
If a manual operation is not obtained for 6 secs while the LED isflashing, the LED will be returned to the input mode.
High Relay & Low Relay Input value High preset point High relay operating time
Low relay operating time Low preset pointOnly High Relay
Input value High preset point High relay operating time
High Relay & Low Relay Input value High preset point High relay operating time
Low relay operating time Low preset poinOnly High Relay
Input value High preset point High relay operating time
www.dbelec.net 53
D-68
D-70
D-200
D-300
D-100
D-60
Cutting Size69
Cutting Size67 x 67
Cutting Size92 x 92
Cutting Size65
Cutting Size53
Cutting Size53
54
Meter Dimensions
D-80
D-800
D-110
D- 110
Transducer (For Meters)The transducer for meter isused with the watt, var and P.F meter.
Cutting Size65
Cutting Size
Cutting Size
Cutting Size
www.dbelec.net 55
Power Factor Meter (Unbalance)Watt Meter (Balance)Var Meter (Balance)
Power Factor Meter (Balance)Watt Meter (Balance)Var Meter (Balance)
Power Factor Meter (Balance)Watt Meter (Balance)Var Meter (Balance)
Power Factor Meter (Unbalance)Watt Meter (Unbalance)Var Meter (Unbalance)
56
3P3W
3P3W
3P4W
Meter Connection