mercedes cr1 can wsp en2 - pontedeira.comfiles.pontedeira.com/200000139-cefd5cff67/mercedes cr1 can...
TRANSCRIPT
3
EMULATOR IMMO
MERCEDES CR1 CAN WSPIS SELLAS UNIVERSAL EMULATOR
Vito 2.2 Cdi
5 plugs
A-class 1.7 Cdi
5 plugs
EDC 1 plug
2.5TD 2.9TD 3.0TD2.5TD 2.9TD 3.0TD
with mechanical and electronic switch
ECM Bosch with HC11E9
E-class Lucas - 4 plugswith mechanical and electronic witch
A-class ECM VDO MSM
1.4 1.6 1.9 gasoline
4
Emulator immo to Mercedes replaces damaged immobilizer or the
car key for the group of Mercedes cars.
It function after made changes in memory content of Engine Control
Module ECM.
In case of losing the cor keys or a cor burglary, it enable to drive off
from the road to the car service.
Due to a low cost, you can leave it in the car instead of buying a new
immo or making car keys duplicate
.
There is a possibility of using it as the additional security!!!
Two LEDs indicating:
White - power
blue - after adjusting it lights constantly and blinks each 2 seconds
when emulator is connected, disconnect CAN fromoriginal immo
A-cIass 17 Cdi - 5 plugsA-cIass 17 Cdi - 5 plugs
Vito 2.2 Cdi - 5 plugs
CUTOFF
CAN-H and CAN-L
(pin 5 and 6)FROM PLUG TOMODULE WSP!
Vito Cdi 5 plugs
Mercedes Vito 2.2 Cdi the starter does not starting, there is an inscription
at the instrument cluster ''STARTERROR”
The ECU is positionedat the passenger side.
In the ECM of Vito 5 plugsCRl, find memory 24C04.
In the memory 24C04 in address:
1 EE to 1F9 enter: 2A 4E 00
GO FF FF 00 9C D4 13 56 01
Disconnected CAN from WSP!!!
1) Run the reading of the
EPROM 24C04
2) Process the file with the
software IMMO Universal
Emulator
3) Write with the new file
generated Disconnected
CAN from WSP!!!
or
Connecting emulator to ECM 5 plugs Vito:
GND 1.04, 1.05, 1.06
CAN-H 2.11.2012
CAN-L 2.12.2012
ACC 1.02.2013
A-Class 1.7 Cdi 5 plugs
Mercedes A-class 1.7 CDI the starter does not starting, there is an inscriptionat the instrument cluster "STARTERROR"
ECU under bonnet on left the side behind engine, covered by plastic.
ECD/MSA 2,5 Td 2,9 Td 3,0 Td (1 plug)
- Sprinter 2,9 Td
- E210 3,0 Td
- C250 2,5 Td
1) Run the reading of the EPROM 24C04
2) Process the file with the software IMMO Universal
Emulator
3) Write with the new file generated
Disconnected CAN from WSP!!!
In memory 24C04 in the address:
1 EE to 1F9 type 2A 4E 00 00 FF FF 00 9C D4 13 56 01
OR
In an older type of engine control module ECM, 1 plug,
need to find the memory 24C02 marked as B58 or memory
24c04.
In memory 24C02 in address 38 and 39 type 2A 4E and in
Addresses from 3F to 42 type 9C D4 13 56
1) Run the reading of the EPROM 24C02 or 24C04
2) Process the file with the software IMMO Universal
Emulator
3) Write with the new file generated
OR
Connecting emulator to ECM, EDC 1 plug.
If there are problems with start, add ACC on 13 pin Computer
EDC
(take it from second leg of LED).
Disconnected CAN from WSP!!!
CAN H and CAN L to the suppressor.
GND - from LED-DIODE
Power from – LED-DIODE
ECU Bosch with HC11E9
ECM Bosch with HC11E9 - in vehicles with engines of 320-6
cylinders, 430-8 cylinders ML 320 and 2,0 gasoline SLK 1998
with mechanical ignition switch
In ECU is Motorola 4E28BHCIIE9 52PLCC
1) Run the reading of the MOTOROLA MCU HC11E9 (Mask
4E28B)
2) Process the file with the software IMMO Universal
Emulator
3) Write with the new file generated, and make
personalization by tester HTT or star Diagnosis because
engine must work 60 seconds, to finish coding
OR
BEFORE READ CONTENT SET OSCILATOR IN TO 5556000Hz!
CHANGE 1st
change in procesor Motorola HC11E9:write from addresses 019 to 01E values FF (ETL 619 to 61E)
15Connecting emulator to ECM:
GND: A3
After make personalization by tester HTT or Star Diagnosis because engine must
work 60 seconds, to finish coding.
GND: A3
+12V ACC: A2
CAN-H: D11
CAN-L: D12
E-dass Lucas - 4 plugs with mechanical andElectronic ignition switch
Mercedes E-class 2.0 diesel 1996
Lucas AOl95459432 ed013 sw25.96 fd30.96
Driver is positioned on the passenger side in the engine comportment.
Motorola HC11KW1 quartz 8MHz connecting programmerX-Prog to motorola:
Pin63 Vssground GND
pin64 Vdd+5V VCC
pin69 Reset B5
pin70 Mod6toground B4
pin71 ModAtoground GND
pin72 RXT B3
pin73 TXD
Connect together pin 70 i 71 before making connection by head ofcable with wire solder to mass.
1) Run the reading of the MOTOROLA MCU HC11KW1
2) Process the file with the software IMMO Universal
Emulator
3) Write with the new file generated, and make
personalization of tester HHT or Star Diagnosis because
engine must work about 60 seconds to finished coding.
OR
Change in processor HC11KW1
In ECM is Motorola HC11KW1 cleaning from address 22A to 22F on FF
19
Connecting Emulator to ECM.
powersupply pin16A
ground pin18C
CANH Pin 1A
CAN H pin10A
After make personalization of tester HHT or Star Diagnosis because engine must
work about 60 second to finished coding.
Disconnect CAN from WSP11!
A-class ECM VDO MSM 1.4 1.6 1.9 Petrol
ECM is set up on air delivery pipe to engine withAir Mass Flow Sensor.Air Mass Flow Sensor.
Connecting emulator:
To read and make change in memory, use programmer.
Red: Power + 12V ACC
Blue: Ground
Green: CAN-H
White: CAN-L
1) Run the reading of the FLASH 29F200 (44pin)
2) Process the file with the software IMMO Universal
Emulator
3) Write with the new file generated
OR
After memory flash is read 29F200 (44pin) write In search windowvalue 03 40 (or 04 40)