Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119 408.224.9167 | www.factorywiz.com

CNC Configuration Sheet

Mazak T32

CNC Parameters: Parameters in column DV1 apply to CMT IO Parameters in column DV2 apply to TAPE IO I1 - 2 (4800 baud) I2 - 3 (2 stop bits) I3 - 0 (No parity) I5 - 3 (8 data bits) I6 - 3 (XON/XOFF handshaking) I7 - 0 (No DC CODE parity) I8 - 5 (IO wait time) I11 - 1 (CR/LF for EOB) I13 - 0 (ISO punch, no TV parity check)

FactoryWiz DNC Settings: Basic Communication 1.01- Port Type: Standard 1.11- Baud: 4800 1.12- Data Bits: 7 1.13- ASCII Even 1.14- Stop Bits: 2 1.15- Handshake: XON/XOFF Sending Options 2.11- Leader: %<10> 2.12- Trailer: % 2.23- Skip lines that contain: % 2.31- Automatic timeout: 7 Receiving Options 3.11- Program identifier 1: O 3.12- Program Identifier 2: 3.21- Receive timeout: 3 3.31- Ignore data before first end-of-block: True 3.32- Ignore data after last end-of-block: True Remote Commands 4.02- Request for file command: GET- 4:11- Request to save command: PUT- Mazatrol Options: 5.01- CMT protocol enabled: TRUE 5.02- CMT controller type: T32 5:11- CMT file extension: .CMT 5.12- CMT filename to use when receiving: Program number 5:14- CMT file suffix: .CMT

Additional Notes:

DNC Systems

Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119 408.224.9167 | www.factorywiz.com

Changing CNC Parameters: 1. Press LEFT PAGE key 2. Press PARAM softkey 3. Cursor to parameter 4. Key in new value 5. Press INPUT 6. POWER DOWN CNC Outputting CNC Programs: Outputting EIA programs: 1. Press PROGRAM softkey. 2. Press PROGRAM FILE softkey. 3. Press DATA I/O 4. Press TAPE I/O softkey. 5. Press PUNCH NC->TAPE softkey. 6. Key in program # (work number) 7. Press INPUT. 8. Repeat Steps 6&7 for additional programs. 9. Press START. Outputting Mazatrol programs: 1. Press PROGRAM softkey. 2. Press PROGRAM FILE softkey. 3. Press DATA I/O softkey. 4. Press CMT I/O softkey. 5. Press SAVE CMT softkey. 6. Key in program # (work number) 7. Press INPUT. 8. Repeat Steps 5&6 for additional programs. 9. Press START. . Inputting CNC Programs: Inputting EIA programs: 1. Press PROGRAM softkey. 2. Press PROGRAM FILE softkey. 3. Press DATA I/O softkey. 4. Press TAPE I/O softkey. 5. Press ALL LOAD TAPE->NC softkey. 6. Press START. Outputting Mazatrol programs: 1. Press PROGRAM softkey. 2. Press PROGRAM FILE softkey. 3. Press DATA I/O softkey. 4. Press CMT I/O softkey. 5. Press LOAD CMT softkey. 6. Key in program # (work number) 7. Press INPUT. 8. Repeat Steps 6&7 for additional programs. 9. Press START. NOTE1: To avoid keying in program #'s for Mazatrol input, use the CMT CONTENTS function to load file contents onto the screen. Then select LOAD NC <- CMT and click START. Values will remain filled in for you.

Wiring Diagram:

Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119 408.224.9167 | www.factorywiz.com

Pinout includes RTS/CTS Handshaking

DB-9 com port Wire color DB-25 CNC Jumper?

(Disconnected) Shield 1

2 (Receive Data) Green 2 (Transmit Data)

3 (Transmit Data) Red 3 (Receive Data)

5 (Signal Ground) Black 7 (Signal Ground)

7 (RTS) Brown 5 (CTS)

8 (CTS) Blue 4 (RTS)

6 (DSR)

8 (DCD)

20 (DTR)

JUMPER