manufacturing and type of die cutting
TRANSCRIPT
-
8/18/2019 Manufacturing and type of Die Cutting
1/48
vanced Die Supplies Advanced Die Supplies Advanced Die Supplies Advanced Die Supp
vanced Die Supplies Advanced Die Supplies Advanced Die Supplies Advanced Die Supp
“Make Ready Supplies to Die for...”
Automated Diemaking Equipment • Benders • Counterplate Locator PinsDieboard • Ejection Rubber • Makeready Tape • Matrix Mylar • Notchers
Nuts & Bolts for Stripping Boards • Phenolic Counterplate MaterialPlotting Pens • Profile Rubber • Profitape • Punches • Rule Pullers Sample
Tables • Solvent • Blanking Supplies • Steel Rule • Super GlueOfficial Bobst Parts •Marbach Products
E-Catalog
*Se Habla Españo
-
8/18/2019 Manufacturing and type of Die Cutting
2/48
We will consistently surpass our customers’expectations by:
• continuous education and development of our staff
• efficient utilization of advancing technology • beneficial partnerships with our manufacturer’• dedication to extraordinary service and quality products At Advanced Die Supplies, we know that helping you succeed is the foundation for our rela- tionship. Our commitment to you, the customer, is the reason we have successfully grown over the lasttwo decades. We are confident you will see this commitment in every phone call, every rec- ommendation and in every shipment.
We are pleased to be of service to our many customers across the United States, Canada and
Mexico. Your demand for extraordinary customer service, combined with high quality and in- novative products at the best price has positioned us as a leading distributor.
This catalog is aimed at helping you easily locate and order the products you need, when youneed them. If you are looking for an item you don’t see listed in our index, please study ourwebsite or call us and we will special order the item or provide you with a referral to the bestsource.
Our Mission at Advanced Die Supplies is to provide solutionsand value for our customers.
Advanced Die Supplies is proud to support these associations
Contact us via e-mail [email protected]
Visit us online atwww.AdvancedDieSupplies.com
Terms on approval of credit.
All major credit cards accepted
-
8/18/2019 Manufacturing and type of Die Cutting
3/483
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
The highest dieboard quality, selection and standards in the world. Bar none.
The LaserPLY product line includes flat dieboards, rotary dieboards and platforms. Our platforms are being used in birch core/maple faceand back flat dieboards, flat dieboards with a wood and polymer veneer combination, as well as core material for rotary dieboard produc-tion. All flat dieboards are available raw, UV-coated or melamine-coated in both clear and proprietary colors.
Every LaserPLY Dieboard exceeds industry standards set by the IADD and the ESU/EDA and, most importantly, by the hardworking individuals who daily make and cut dies and demand excellence in the dieboards they use. In the rare case you receive a dieboard out of specifica-tion, we’ll replace it for you free of charge.
For your convenience, Flat LaserPLY Dieboards come in a vast array of panel sizes and thicknesses—metric and imperial—to satisfy allproprietary machinery, laser die cutting, corrugated, folding carton and stripping application needs. Whether you like to buy large and nestyour dies or buy small for easy in-house handling and no cutting or nesting, we deliver. If you don’t see it listed, just ask. We’ll have the size
you need custom-made for your application.
OUR DIEBOARD GRADES:
PG Wood Imports’ dieboards have been added to our family of productsbecause they represent the highest quality in their category.
– Alex Gigon, Director Service Operations, Bobst North America Inc.
LaserPLY Premium – Zero defects, minimal color streak on both sides. Designed for the diemaker who requires the ultimate qualityassurance.
LaserPLY Advantage – Minimal defects and color streak on both sides. This is the industry-standard grade and the best value.
LaserPLY Advantage UVC – Minimal defects and color streak on both sides, UV-coating on both sides. This is the industry-standardgrade for UV-coated dieboards, offering stable moisture content and a smooth surface.
LaserPLY Platform – Proprietary grade developed by PG Wood Imports and used as substrate in flat maple and flat polymer combi-construction dieboards. Thin LaserPLY Platforms are being used in rotary dieboard production and for other curved plywood components.
-
8/18/2019 Manufacturing and type of Die Cutting
4/484
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Arctic White
Daffodil
Alpine
Blueberry
Light Pink
Rose Pink
TitaniumLight Orange
Moonstone
Platinum
Fire
Orange
Beige
Lilac
Pale Blue
Ocean
Flame
HollyVanilla
Mustard
Lime
Royal Blue
Ivory
White
Toffee
Apple Green
Moss
Peach
OliveBright Green
Terracotta
Yellow
Cornflower
Avacado
Ice Blue
Ebony
0.30 x 0.50
0.30 x 0.60
0.30 x 0.80
0.30 x 1.00
0.30 x 1.20
0.30 x 1.30
0.30 x 1.40 0.30 x 1.50
0.30 x 1.70
0.40 x 0.50
0.40 x 0.60
0.40 x 0.80
0.40 x 1.00
0.40 x 1.20
0.40 x 1.30
0.40 x 1.40
0.40 x 1.50
0.40 x 1.600.40 x 1.70
0.40 x 1.90
0.40 x 2.70
0.45 x 0.80
0.45 x 1.20
0.45 x 1.30
0.45 x 1.40
0.45 x 1.50
0.50 x 0.80
0.50 x 1.00
0.50 x 1.200.50 x 1.30
0.50 x 1.40
0.50 x 1.50
0.50 x 1.60
0.50 x 1.70
0.50 x 1.90
0.50 x 2.10
50 - 100
50 - 100
50 - 150
100 - 200
190 - 230
300 - 350
320 - 420355 - 430
460 - 520
50 - 100
50 - 100
50 - 150
100 - 200
150 - 240
320 - 400
330 - 420
370 - 440
440 - 500 420 - 540
530 - 580
700 - 800
50 - 150
225 - 310
340 - 410
350 - 420
375 - 450
50 - 150
170 - 200
285 - 330340 - 420
350 - 420
440 - 500
490 - 520
500 - 550
540 - 590
570 - 630
2 - 4
2 - 4
2 - 6
4- 8
7 -9
12 - 14
13 - 1714 - 17
18 - 20
2 - 4
2 - 4
2 - 6
4 - 8
6 - 9
13 - 16
13 - 17
14 - 17
17 - 2019 - 21
21 - 23
28 - 31
2 - 6
9 - 12
13 - 16
14 - 17
15 - 18
2 - 6
7 - 9
11 - 1313 - 17
14 - 17
17 - 20
19 - 20
20 - 2221 - 23
22 - 25
50 - 100
50 - 100
50 - 100
100 - 175
170 - 195
200 - 250
225 - 290250 - 300
300 - 335
50 -100
50 - 100
50 - 150
100 - 175
150 - 200
225 - 275
225 - 290
250 - 300
290 - 335360 - 375
350 - 400
460 - 500
50 - 150
185 - 225
240 - 270
240 - 290
260 - 300
50 - 150
165 - 190
210 - 240240 - 290
240 - 290
290 - 335
360 - 370
350 - 375
350 - 400
375 - 410
Color Code A B Board Wt
Precision Creasing Solutions
Microns (0.001”)
Board Thickness
-
8/18/2019 Manufacturing and type of Die Cutting
5/485
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Aubergine
Navy Blue
Spearmint
Purple
Green
Diamond White
TangerineRacing Green
Sand
Honeysuckle
Burgandy
Sherbet
Rosewood
Cinnamon
Coffee
Sandstone
Red
DuskPeppermint
Onyx
Ruby
Lavendar
Pacific Blue
Ash Grey
Pink
Lemon
Manilla
Blue
NastortiumBluebell
Primrose
Brown
Pistachio
0.60 x 1.30
0.60 x 1.50
0.60 x 1.60
0.60 x 1.70
0.60 x 1.90
0.60 x 2.10
0.60 x 2.30 0.60 x 2.50
0.60 x 2.70
0.60 x 3.00
0.65 x 2.10
0.70 x 1.30
0.70 x 1.50
0.70 x 1.70
0.70 x 1.90
0.70 x 2.10
0.70 x 2.30
0.70 x 2.500.70 x 2.70
0.70 x 3.00
0.80 x 1.50
0.80 x 1.60
0.80 x 1.70
0.80 x 1.90
0.80 x 2.10
0.80 x 2.30
0.80 x 2.50
0.80 x 2.70
0.80 x 3.001.00 x 2.30
1.00 x 2.50
1.00 x 3.00
1.400x3.00
350 - 450
460 - 520
490 - 530
525 - 600
540 - 600
580 - 630
630 - 700700 - 780
700 - 800
750 - 850
580 - 650
350 - 450
480 - 550
530 - 600
550 - 600
600 - 680
640 - 700
700 - 800700 - 800
750 - 850
480 - 550
490 - 540
540 - 600
560 - 620
620 - 700
680 - 760
700 - 800
700 - 800
780 - 880700 - 760
700 - 800
800 - 1000
800-1000
14 - 18
18 - 20
19 - 21
21 - 24
21 - 24
23 - 25
25 - 2728 - 31
28 - 31
30 - 33
23 -26
14 - 18
19 - 22
21 - 24
22 - 24
24 - 27
25 - 28
28 - 3128 - 31
30 - 33
19 - 22
19 - 21
21 - 24
22 - 24
24 - 28
27 - 30
28 - 31
28 - 31
31 - 3528 - 30
28 -31
31 - 39
31-39
250 - 300
300 - 335
360 - 370
350 - 400
350 - 400
385 - 410
400 - 465
460 - 500
460 - 500
485 - 565
385 -435
250 - 300
350 - 365
350 - 400
350 - 400
400 - 450
420 - 465
460 - 500
460 - 500
485 - 465
350 - 365
360 - 375
350 - 400
365 - 400
400 - 465
450 - 500
460 - 500
460 - 500
490 - 575
460 - 500
460 - 500
535 - 665
565-665
Color Code A B Board Wt
* Sizes for Kiss and Jazz are available in Standard, Large, Off-Centre, Mini, and Multi-Crease** Some sizes of Jazz are also available in Quadra, with chamfered shoulders, to reduce stress and cracking on corrugated board.
Microns (0.001”)
Board Thickness
Product ProfileKiss Crease is the optimum balance between cost and quality. Kiss has precision engineered plastic shoulders on a micro thin polyester film base with a perfectly registered locator.
Decades of continuous development and experience have lead to efficient manufacture to the highest standards giving this optimum cost and quality balance.
Jazz is the ultimate creasing technology. Decades of experience have been applied to the development of Jazz. Precision engineered plastic shoulders, a micro thin polyester film
base and a profile registered locator are manufactured to the highest quality standards. Its unique curved profile shoulders allow substrate to glide easily over the matrix to allow
increased press speed, decreased substrate stretching and reduced make ready.
-
8/18/2019 Manufacturing and type of Die Cutting
6/486
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
SYNTRIXSYNTRIX Matrix, from Bobst, is the most
cost-effective matrix system ever. Using the latest
technologies and synthetic, DURABLE materials,
SYNTRIX is the logical result of 40 years constant
development. SYNTRIX is the solution for long runs.
FIBRIX PROFIBRIX PRO Matrix, from Bobst, is the ultimate
advanced matrix system. Combining pressboard with
modern materials, FIBRIX offers up to 3 ti mes the
durability of similar matrices. Perfect for difficult or
recycled board. Also a solution for label-laminated
corrugated creasing.
METRIXThe Original steel-based matrixMETRIX Matrix self-locating creasing matrix from
Bobst, is the world’s first and most widely
used creasing matrix. It is extremely durable arid
accurate and provides benefits in time and cost over
rival systems.
*18 other sizes available. Call our Customer Service staff for more
information or for help calculating other calipers
Reverse Bend Matrix This self-locating creasing matrix can
be used where creasing on both sides
of the board is required, or where a
creasing bead inside the crease is not
desirable. The two creasing rules are
inserted into the die to form the chan-
nel, and the ridge on the matrix acts
as a creasing rule.
U BendFor creasing corrugated and solid
board through 180°. This unique
format reduces the stress that can
occur with Multicrease matrix.
TIP: Try U Bend on roll-over scores
where cracking may occur.
Reverse Bend Sizes
SYNTRIX & FIBRIX Matrix Configurations
The world’s most advanced creasing make-ready system.
Three innovative formats to best suit every job’s unique needs.
Patented & produced to ISO 9002 specifications.
CommonSizes
Board Thickness
Rule to RuleDistance
(channel width)
RB1 RedRB2 Yellow
RB3 Buff RB4 GreenRB5 Blue
RB6 Violet
.010”-.020”
.020”-.030”
.030”-.040”
.040”-.050”
.050”-.060”
.060”-.070”
.080”
.110”
.160”
.180”
.200”
.240”
-
8/18/2019 Manufacturing and type of Die Cutting
7/487
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Board Thickness
(inches)
Crease Rule
Width
Crease Rule
Height
Matrix Size
(mm)
.006”
.008”
.010”
.012”
.014”
.016”
.018”
.020”
.022”
.022”
.024”
.024”
.026”
.028”
.030”
.030”
.032”
.032”
.035”
.039”
.043”
.047”
.047”
.051”.055”
2pt2pt
2pt2pt2pt2pt2pt2pt2pt2pt3pt2pt3pt
3pt3pt3pt4pt3pt4pt4pt4pt4pt4pt
6pt6pt
orororororororororor
orororororororororor
oror
.930” or .932”
.928” or .930”
.926” or .928”
.924” or .926”
.922” or .924”
.920” or .922”
.918” or .920”
.916” or .918”
.914” or .916”
.914” or .916”
.912” or .914”
.912” or .914”
.910” or .912”
.908” or .910”
.906” or .908”
.906” or .908”
.904” or .906”
.904” or .906”
.900” or .902”
.896” or .898”
.892” or .894”
.888” or .890”
.888” or .890”
.884” or .886”.880” or .882”
0.3 x 0.80.3 x 1.0
0.4 x 1.10.4 x 1.10.4 x 1.20.4 x 1.30.5 x 1.40.5 x 1.40.6 x 1.50.6 x 1.70.6 x 1.70.6 x 1.90.7 x 2.1
0.7 x 2.10.8 x 2.30.8 x 2.50.8 x 2.50.8 x 2.71.0 x 3.01.0 x 3.01.2 x 3.21.2 x 3.51.2 x 4.0
1.4 x 4.01.4 x 4.0
0.4 x 1.20.4 x 1.30.4 x 1.40.5 x 1.50.5 x 1.50.6 x 1.70.6 x 1.90.6 x 1.90.6 x 2.10.7 x 2.3
0.7 x 2.30.8 x 2.50.8 x 2.70.8 x 2.70.8 x 3.01.0 x 3.21.0 x 3.21.2 x 3.51.2 x 4.01.2 x 5.0
1.4 x 5.01.4 x 5.0
Matrix & Crease Rule Selector Guide - Based on .937 cutting rule
Please note these sizes are suggestions only. Variations in board quality and environment may make alterations necessary.
Call our customer service staff for personal assistance.
PART # YELLOW PART # ORANGE PART # GREEN PART # BLUE c2c in Inches
H x W /c2c*(mm) H x W /c2c*(mm) H x W /c2c*(mm) H x W /c2c*(mm)
BGUCXU0650 0.6 x 5.0 /3 BGUCXU0750 0.7 X 5.0 /3 BGUCXU0850 0.8 X 5.0 /3 BGUCXU1050 1.0 X 5.0 /3 1/8”
BGUCXU0660 0.6 X 6.0 /4 BGUCXU0760 0.7 X 6.0 /4 BGUCXU0860 0.8 X 6.0 /4 BGUCXU1060 1.0 X 6.0 /4 5/32”
BGUCXU0670 0.6 X 7.0 /5 BGUCXU0770 0.7 X 7.0 /5 BGUCXU0870 0.8 X 7.0 /5 BGUCXU1070 1.0 X 7.0 /5 3/16”
BGUCXU0680 0.6 X 8.0 /5 BGUCXU0780 0.7 X 8.0 /5 BGUCXU0880 0.8 X 8.0 /5 BGUCXU1080 1.0 X 8.0 /5 3/16”
BGUCXU0690 0.6 X 9.0 /6.5 BGUCXU0790 0.7 X 9.0 /6.5 BGUCXU0890 0.8 X 9.0 /6.5 BGUCXU1090 1.0 X 9.0 /6.5 1/4”
BGUCXU06100 0.6 X 10.0 /8 BGUCXU07100 0.7 X 10.0 /8 BGUCXU08100 0.8 X 10.0 /8 BGUCXU10100 1.0 X 10.0 /8 5/16”
CORRUGATE | U-BEND
-
8/18/2019 Manufacturing and type of Die Cutting
8/488
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
0.30.30.30.30.30.30.3
0.30.30.30.3
0.40.40.40.40.40.40.40.40.40.4
0.4
0.450.450.450.450.450.450.450.450.450.45
0.60.81.01.11.21.31.4
1.51.61.71.9
0.60.81.01.11.21.31.41.51.61.7
1.9
0.81.01.11.21.31.41.51.61.71.9
79797979797979
79797979
79797979797979797979
79
79797979797979797979
ChannelDepth
ChannelWidth
Feet /Box
0.50.50.50.50.50.50.5
0.50.50.50.50.5
0.550.550.550.550.550.550.550.550.55
0.550.55
0.81.01.11.21.31.41.5
1.61.71.92.12.3
0.81.01.21.31.41.51.61.71.9
2.12.3
79797979797979
7979797979
797979797979797979
7979
ChannelDepth
ChannelWidth
0.60.60.6
0.60.60.60.60.60.60.60.60.60.60.60.60.60.60.6
0.60.60.6
0.650.650.650.650.650.650.650.650.650.650.650.650.650.650.650.650.650.650.65
0.70.70.70.70.7
0.70.70.70.70.70.70.70.70.70.70.70.70.7
1.01.11.2
1.31.41.51.61.71.92.12.32.52.73.03.23.54.05.0
6.07.08.0
1.31.41.51.61.71.92.12.32.52.73.03.23.54.04.55.06.07.08.0
1.31.41.51.61.7
1.92.12.32.52.73.03.23.54.04.55.06.08.0
797979
797979797979797979797959594949
494949
79797979797979797979795959494949494949
7979797979
79797979797959594949494949
ChannelDepth
ChannelWidth
Feet /Box
0.80.80.8
0.80.80.80.80.80.80.80.80.80.80.80.80.8
1.01.01.01.01.01.01.01.01.01.01.0
1.21.21.21.21.21.21.21.21.2
1.41.41.41.41.41.41.4
1.41.4
1.61.61.61.61.61.61.61.61.6
1.51.61.7
1.92.12.32.52.73.03.23.54.04.55.06.08.0
2.32.52.73.03.23.54.04.55.06.08.0
3.03.23.54.04.55.06.07.08.0
3.03.23.54.04.55.06.0
7.08.0
3.03.23.54.04.55.06.07.08.0
797979
79797979797959594949494949
7979797959594949494949
595959494949494949
59595949494949
4949
595959494949494949
ChannelDepth
ChannelWidth
Feet /Box
SYNTRIX Matrix Sizes
SYNTRIX Matrix from Bobst, is the most cost-effective matrix system ever. Using the
latest
technologies and synthetic, DURABLE materials, SYNTRIX is the logical result of 40
years constant development. SYNTRIX is the solution for long runs.
Available:
Standard, OC, MC, IC and RB
Strips or Coils
-
8/18/2019 Manufacturing and type of Die Cutting
9/489
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
0.30.30.30.30.3
0.30.30.30.3
0.40.40.40.40.40.40.40.40.4
0.4
0.50.50.50.50.50.50.50.50.50.50.5
0.81.01.11.21.3
1.41.51.61.7
0.81.01.11.21.31.41.51.61.7
1.9
1.01.11.21.31.41.51.61.71.92.12.3
5959595959
59595959
595959595959595959
59
5959595959595959595959
ChannelDepth
ChannelWidth
Feet /Box
0.60.60.60.60.6
0.60.60.60.60.60.60.60.60.60.60.60.6
0.7
0.70.70.70.70.70.70.70.70.70.70.70.70.70.70.7
1.21.31.41.51.6
1.71.92.12.32.52.73.03.23.54.05.06.0
1.3
1.41.51.61.71.92.12.32.52.73.03.23.54.05.06.0
5959595959
595959595959595959494949
59
595959595959595959595959494949
ChannelDepth
ChannelWidth
Feet /Box
0.80.80.80.80.80.80.80.80.80.80.80.80.80.8
1.01.0
1.01.01.01.01.01.01.0
1.51.61.71.92.12.32.52.73.03.23.54.05.06.0
2.32.5
2.73.03.23.54.05.06.0
5959595959595959595959494949
5959
59595959494949
ChannelDepth
ChannelWidth
Feet /Box
1.21.21.21.21.21.2
1.41.41.41.41.41.4
1.61.6
1.61.61.61.6
3.03.23.54.05.06.0
3.03.23.54.05.06.0
3.03.2
3.54.05.06.0
595959494949
595959494949
5959
59494949
ChannelDepth
ChannelWidth
Feet /Box
FIBRIX PRO Matrix Sizes
FIBRIX PRO Matrix, from Bobst, is the ultimate advanced matrix system. Combining
pressboard with modern materials, Trax offers up to 3 times the durability of similar
matrices.
Available:
Standard, OC, MC, and IC
Strips or Coils
-
8/18/2019 Manufacturing and type of Die Cutting
10/4810
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Metrix Matrix Sizes
Original Matrix self locating creasing matrix, from Bobst, is the world’s first and most
widely used creasing matrix. It is extremely durable and accurate and provides
benefits in time and cost over rival systems.
Black
Brown
Grey
Orange
Yellow
Green
White
Red
Buff
White
Yellow
40 Buff
40 Buff
40 Buff
40 Buff
50 White
50 White
50 White
50 White
60 Yellow
60 Yellow
60 Yellow
50 Yellow
0.55
0.7
0.8
0.9
1.3
1.6
2.0
2.0
0.38
0.43
0.48
0.38
0.38
0.38
0.38
0.43
0.43
0.43
0.43
0.48
0.48
0.48
0.48
1.3
1.5
1.9
2.3
3.0
3.8
3.8
5.0
1.0
1.3
1.5
1.0
1.0
1.0
1.0
1.3
1.3
1.3
1.3
1.5
1.5
1.5
1.5
2/3
2/3
2/3
2/3
4/6
4/6
4/6
4/6
2/3
2/3
2/3
010-016”
016-020”
024-028”
032-036”
036-048”
040-050”
048-060”
058-072”
006-010”
010-016”
016-020”
9/64”
1/8”
5/32”
3/16”
1/8”
9/64”
5/32”
3/16”
1/8”
9/64”
5/32”
3/16”
79
79
79
79
39.5
39.5
39.5
39.5
59
59
59
(3.5mm)
(3mm)
(3mm)
(4mm)
(3mm)
(3.5mm)
(3.5mm)
(3.5mm)
(3mm)
(3.5mm)
(3mm)
(5mm)
Color
ChannelSize
ChannelDepth
(d)
ChannelDepth
ChannelWidth
(w)
ChannelWidth
Locatorpointsize
Use onboard
thickness
Centerto Center
FeetperBox
???
Extra Deep
Off Center
Multi-Crease
22 Gold
32 Orange
40 Buff
50 Cloud
50 White
60 Lime
60 Yellow
67 Violet
67 Mauve
75 Olive
75 Green
83 Pink
83 Maroon
90 Red
105 Blue
120 Brown
120 Brown
150 Grey
150 Grey
200 Black
200 Black
250 Cream
250 Cream
0.38
0.38
0.38
0.38
0.43
0.43
0.48
0.48
0.53
0.53
0.58
0.58
0.63
0.68
0.79
1.0
1.0
1.3
1.3
1.6
1.6
2.0
2.0
0.56
0.8
1.0
1.3
1.3
1.5
1.5
1.7
1.7
1.9
1.9
2.1
2.1
2.3
2.7
3.0
3.0
3.8
3.8
5.0
5.0
6.3
6.3
1/1.5
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
2/3
3/4
4/6
3/4
4/6
3/4
4/6
3/4
4/6
Paper
004-006”
006-010”
006-016”
010-016”
010-016”
016-020”
016-020”
020-024”
020-024”
024-028”
024-028”
028-032”
032-036”
036-040”
040-048”
040-048”
048-056”
048-056”
056-064”
056-064”
064-072”
064-072”
79
79
79
79
79
79
79
79
79
79
79
79
79
79
79
39.5
39.5
39.5
39.5
39.5
39.5
39.5
39.5
Color ChannelDepth
(d)
ChannelWidth
(w)
Locatorpointsize
Use onboard
thickness
Feetper Box
Standard
-
8/18/2019 Manufacturing and type of Die Cutting
11/4811
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
To Select Matrix Size
To Calculate the Correct Channel Width
To Calculate the Correct Channel Depth
-
8/18/2019 Manufacturing and type of Die Cutting
12/4812
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Makeready Accessories
Tympan Paper Spot SheetsMultiple applications in printing and diecutting
makeready processes for letterpress, lithography,
offset, gravure and flex-ography. Surface-treated to
repel moisture and most plate or blanket washes. This
high density paper is .006” thick.
Available in rolls: 36”, 45” and 54” wide
Pre-cut top sheets and specialty sizes can be supplied
Carbon Roll & Carbon SheetsBlack, one-time use carbon paper.
Available in rolls .0015” x 44” x 1000’
or sheets 26” x 39” (100 sh/pkg)
Tripplex Spot Sheets The high-tensile strength of the patented polypropyl-
ene foil center makes this a superior spot sheet. Trip-plex is especially good for long runs and repeat uses.
Special polypropylene foil center
Long life for repeat runs
Tear resistant
Water proof
Available:
47 x 164’ rolls
.005” Thick
Super Cut Bench Press
• Advanced shearing action miters both ends with one cut.
• Waste collects beneath shears for add ed convenience.
• Adjustable to fit different matrix width.
• Length gauge for repetitive cutting.
• Simple & economical blade replacement.
Multi CutterCuts mitered angle. For all creasing matrix or ejection rubbers as well.
Cuts 45 - 120 degree angles.
-
8/18/2019 Manufacturing and type of Die Cutting
13/4813
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Makeready Accessories
Jute TagManila-colored, medium-hard board ideally suited for short runs.
Available:
In 24” x 36” sheets
.008” - .036” thick
Specify plain, adhesive or kraft-backed
PressboardPearl gray, hard surfaced board is ideally suited for medium runs.
Available:
In 24”x 36” sheets,
.010” - .036” thick.
Specify plain, adhesive or kraft-backed
Vulcanized FiberboardRed, extra through-hardened board is ideal for long runs or for recycled
substrates.
Available:
In 24” x 36” sheets,
.010”- .040” thick
Stereo Embossing BoardWhite Stereo Embossing board is the economical alternative to
two-plate embossing and debossing. Eliminate one-half of a stan-
dard brass, steel or composite plate set and make your own coun-
ter. Easier and safer than “Pour a Counter” with superior results.
Available:
In a variety of sheets from 19” x 19” to 20” x 60” depending on thickness.
Available thicknesses: .030” - .066”
Steel Shim TapePressure sensitive adhesive makeready tape used to level a plate
or press. Also used behind the die. All rolls are 5/16” wide.
Available:
.001”, .002” and .005” thick;
Rolls 33’, 66’, 99’ and 197’ long
Profitape This plasticized, pressure sensitive adhesive, makeready tape exhibits great tear and
moisture resistance. Its high-tensile strength makes it well-suited for long runs and on
repeat-use spot sheets.
Benefits:
Saves time in application
Easier to apply
Less waste
Does not wrinkle
Prevents cutting plate rust
Available: 1/4” wide Thicknesses: .003” yellow, .002” red, .001” blue
Spot TapeConventional Makeready TapePaper Makeready Tape meets the specific needs of the diecutting
industry.
Available in:
1/4 “ and 1/2” wide rolls
.0015”, .003” and .006” thick
Pressboard
-
8/18/2019 Manufacturing and type of Die Cutting
14/4814
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Makeready Accessories
“Very safe toxicity profile...much safer than chlorinated
solvents, toluene, xylene, etc.”
Recommended by:
Benefits:
•Extremely low NFPA Hazard Classication
(Health-Flammability-Reactivity)
•Low odor
•Meets California’s tough SCAQMD Rule 102
& BAAQMD Regulation 8
•Contains no CFC’s
•High Flashpoint over 100°F
(1-2-0)
Cleanup Solvent 22 and Oil-Flo 141 are available in
1 Gallon, 5 Gallon Pails and 55 Gallon drums.
Spray bottles are also available.
AdhesiveRemover!Removesadhesivefromexo
foldergluers,laminators,and
oil&greasefromallsurfaces:
oors,sidesofmachines,
machineparts,tools,
hydraulicpumpsandoilspills.
Removestheadhesive
residueofmatrix,and
countersfromcuttingplates.
Safetouse&DriesFast!
*Activated and Rinses clean with Water
-
8/18/2019 Manufacturing and type of Die Cutting
15/4815
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Counterplate Locator Pin & WasherDesigned to locate and transfer phenolic counterplates with precise
registration. Durable plastic, aluminum pins and washers are re-usable.Phenolic Countamat Material
A substitute for hand-cut counterboard, Matrix and costly steel coun-
terplates. Achieve close tolerance and the durability for extremely
long runs with Bobst Countamat counters.
Features:
Superior film adhesion
Extended impression life
Lighter than steel
Accurate machinability
Less down time at changeover
Easily removed and reused
Availability:
Rigid Material
0.015” - 0.048” thick
Standard sheets are 42-1/8” x 41-5/16”
Makeready Accessories
Design Tools
MylarAvailable in matte (frosted) one-side, and clear.
Standard Sizes:
0.003”- 0.005” thick
36”- 60” wide rolls
Roll lengths from 20 - 100 yds
Other dimensions and sheeted sizes available on request.
Fisher Space PensPlotter & Sample Maker PensAdvanced Die Supplies is the exclusive distributor of Fisher Space Pens for the
Converting Industry. Gas-pressurized pens for plotting. Compatible with Alphameric,
Elcede, Datatech, Kongsberg, Misomex, ZUND and virtually all other tables.
Available: 3”and 3.5” Fine, Medium & Bold
Colors: Black, Blue, Light Blue, Red, Green, Brown, Orange, Silver & Gold
High Speed Lockup QuoinsQuickly lock up dies in the press or chase. Bar-Plate’s
unique construction applies even pressure across the
entire face of the quoin, ensuring a tight fit.
Available: 3”, 6”, 9” and 12”
Special Bobst® Quoins are available in 9”
Standard “T” handle key and 6” right angle key, as
well as the newest Torque Quoin Key, are available
separately.
-
8/18/2019 Manufacturing and type of Die Cutting
16/4816
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Diecutting Plates
Cutting Plates, Back Up Plates & JacketsJackets for Miehle, Miller, L&M, Viking, Heidelberg and other
regular and converted presses. High carbon steel in excess of 35
RC hardness. All jackets manufactured to your
specifications. Thicknesses from .050” to .125”.
Most common thickness is .083”.
Plates for Brausse, C&P, Champlain, Condes,
Consolidated, Crosland, Heidelberg, Imperia,
Kempsmith, Kluge, Mercury, Preco, S&S, Schwabe,
Standard, Thomson, Wupa and Zerand also stocked.
Standard hardness is 47-52 HRC.
Plates available in all sizes for all presses in
thicknesses from 1/16” to 1/2”.
Special plates require a delivery time of 5-7 weeks.
Bobst® Cutting PlatesReplacement plates for Bobst® presses and other high speed platen presses.
High carbon steel is hardened, tempered, ground and polished to produce a superior quality plate. Immediate
shipment of stock plates for SP 76-E, SP 102-E/SE, SP 102 Evoline, SP 102-E II/Evoline +, SP 102-CE/CE II, SP 102-
CER/CER II, SP 103-E/ER, SP 104-E/ER, Speria 106 E & Commercial 106 E, SPanthera 106 LE/LER, SPrintera 106
PER, SP 130-E/E II/SE, SP 130-ER/ER II/SER, SP 142-E/ER & SPeria 142 E, SP 142-CER/CER II, SPanthera 145 PER &
SPrintera 145 PER, SP 162-CE, SP 162-CER, SPO 1575, SPO 160 S & VISION, SPO 1600/ A & APR, SPO 2000 & 203
A, MASTERCUT 1.7, MASTERCUT 2.1.
Chase PlatesFabricated to meet exact OEM specification.
New and used Bobst® Chases available.
Thin PlatesFor job to job makeready.
1mm thick for most highspeed presses.
*For complete hardness, size and, part number list please visit our website,
www.AdvancedDieSupplies.com
*Now in stock in CA. Pleasecall to check which sizes arein stock.
-
8/18/2019 Manufacturing and type of Die Cutting
17/4817
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Diemaking Accessories
Rawhide Mallets Traditional die maker’s mallet.
Sizes: #3 1-3/4”, #4 2”, #5 2-3/4”
Diemaker’s Mallet & Replacement HeadsHeavy duty elastomer mallets are made to wear evenly and will
not break or splinter. Tough, long-lasting heads are replaceable.
Sizes. #4 2” x 3.5”, #4L 2” x 5”, #6 2 3/4” x 4 3/4”
Diemaker’s ApronRugged denim material with durable stitching provide the
diemaker with protection and convenience. Comes with two
Utility pockets and tie strings attached.
Kevlar® Safety GlovesStrong, lightweight and flexible Dupont® Kevlar ® fiber protects hands from cuts and
abrasions. PVC dots give superior grip. Available wit h and without fingers. For sizing,
measure around the widest part of the palm.
Available Sizes:S (7 - 8”) M (8-1/2 - 9”) L (9-1/2 - 10”) XL (10-1/2 - 11”
Corrugated FastenersUsed to join multiple die boards to form larger steel
rule dies.
Available: 3/8” x 1”, 1/2” x l”, and 5/8” x 1”
Very Red Durable Die Makers MalletDurable Polyurethane mallets.
_______________________________Sizes: S - 1-3/4”, M - 2” x 5”, L - 2-3/4” x 4-3/4”
-
8/18/2019 Manufacturing and type of Die Cutting
18/4818
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Diemaking Accessories
Laborsaber Jig Saw This jig saw has design innovations that greatly increase sawing speed, yet retain the
accuracies you need and expect.
Available throat sizes: 36”, 48”, 52”, 60”, 62” and 70”. Options include: jig head at 90°for larger dieboards, magnifying glass, table extension.
Call for pricing and addtional information.
Jig Saw BladesBlades for Laborsaber, Cutawl, Richards and more.
1-½, 2, 3, 4, 6 and 8 point
Cutawl sizes #42, #43, #44
Regular and Reverse Tooth configuration
Retractable style
Jig blade glides for 1-1/2, 2, 3, 4, 6 and 8 point
Cutawl Saw
Leading saw for rotary dies. Made especially for the dense,hard maple and birch dieboards. Cutawl accurately saws
curved rotary dieboards, flat dieboards and stripping
boards.
Available:
K-12F for flat dieboard
K-12C-50 for 50” rotary dieboard
K- 12C-66 for 66” rotary dieboard
Cutawl BladesCutawl sizes #42, #43, #44 for 2, 3 and 4 point
* For Die Benders and other Die Bending equipment, please visit our website www.AdvancedDieSupplies.com
SeperatorFor Conventional Stripping.
Lead Edge GuardsReduces Lead Edge knife failure by acting as a brace for rotary dies.
Martin Hoops177mm 618 for 7” dies.
270mm 922-924, 10-5/8” for 38” dies.
Hoop 1228-1232-1330, 13-3/4” for 50” dies.
487mm 1628, 19-3/16” for 66” dies.
Seperators For Conventional StrippingLeft and RIght.
-
8/18/2019 Manufacturing and type of Die Cutting
19/4819
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Diemaking Accessories
Pocket Scribe
#81: 3/8” diameter with 5-7/8” length
#83: 1/4” diameter with 4-3/4” length
Replacement tips available
Mini Perf-a-TypeDesigned for litho-laminated and high-graphic corrugated. 3/8” high for the most
discreet demarcation. Highest quality for definition.
Perf-a-Type3/4” high letters and numbers on 1” base for easy attachment to flat
or rotary dieboards. Attach with adhesive, nails or convenient perf-a-type tracks.
3/8” high letters and numbers
on 1/2” adhesive-backed base.
Attach with adhesive, nails or
convenient mini tracks.
Perf-a-Type Track For easiest placement of all perf-a-type, use these hardy plastic holders.
Available for regular and mini perf.
• Blue Mini Perf A Guide, .029” or .74mm Thick.
• Medium Blue Mini Perf A Guide, .094” or 2.40mm Thick.
• Red Mini Perf A Guide, Rotary .190” or 4.75mm Thick.
• Blue Perf A Guide 5/8”, Flat.
• Red Perf A Guide 1/2”, Rotary.
*With our thicker basesshimming is reduced or
even eliminated.
Rotary Miter KnivesMiter Tight, pre-cut miter rule, is designed to prevent scrap buildup by matching the
contour of the bevel rules commonly used in lead edges. Blades are pre-cut to 1/4”
lengths to save time in ruling and simplify programming.
Curved available: .960”; .990”; 1.00”, 1.025”
Straight available: .937” .970”, .990”, 1.00”
-
8/18/2019 Manufacturing and type of Die Cutting
20/4820
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Nicking Tools
Quicknick GrinderEnsure accurate, consistent, perpendicular nicks with this diemaking tool. The design of
the Quicknick Grinder guarantees that nicks will be properly placed and prevent
premature break up of the sheet. Adjustable depth stop, easy-to-read scale on base
and Lexan safety guard make this grinder a professional tool.
Grinding Wheels
Available thicknesses: 0.010” - 0.062”
Diameters: 1”- 3”, with inside diameters 1/8”, 9/32”, 1/4”
Dremel Moto-ToolEasy-to-use, economy nicking grinder comes with a 1/8” mandrel and collet, but also
accommodates 1/16”, 3/32” and 1/8” collets.
Dremel WheelsCommon sizes #409, #420
Other sizes available.
Nicking Chisel SetCost-effective alternative to precise grinders. The set comes with
a knurled holder and three standard tips: .020”, .030” and .040”.
Better than screwdrivers, tiles or other pieces of k nife.
Rule SharpenerAccu-Sharp rule sharpener effectively touches up dull spots on the die.
Sharpening the rule is only recommended when cutting into a soft cutting
pad and only to finish a job before re-ruling.Reinforced Grinding Wheels
Available thicknesses: 0.020” - 0.067”
Outside Diameter : 2”, Arbor: 1/8”
-
8/18/2019 Manufacturing and type of Die Cutting
21/4821
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
CorrUgate Solutions to Cracked Scores
BSA1031082500
BSA1031082600
BSA1031082700
BSA1031082800
BSA1031082900
BSA1031083000
BSA1031083100
BSA1031083200
BSA1031083300
BSA1031083400
BSA1031083500
Part # 5.0mm RED SOFT-C
6.0mm RED SOFT-C
6.5mm RED SOFT-C
7.5mm RED SOFT-C
8.0mm RED SOFT-C
8.5mm RED SOFT-C
9.0mm RED SOFT-C
9.5mm RED SOFT-C
10.0mm RED SOFT-C
10.5mm RED SOFT-C
11.0mm RED SOFT-C
Description SizeRUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORERUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
RUBBA 30m 25 SHORE
Bobst Red Soft-C Rubber
BOBST Red Soft-C Rubber BOBST Red Soft-T Rubber BOBST G Profile Rubber
Size Guide for 5/8” Die Board:
Rule Height .875”
.900”
.907”
.918”
.923”
.937”
Rubber Height6.5 MM
7.5/8.0 MM
7.5/8.0 MM
7.5/8.0 MM
8.0 MM
8.0/8.5 MM
-
8/18/2019 Manufacturing and type of Die Cutting
22/4822
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Diemaking Solutions
Centering BracketCompatible with Bobst® 103 and 104 systems for fast lock frames.
Centerline StopsCentering stop used on Centerline 1 and Centerline 2 systems;
the Black center line stop used on the upper (male) stripping jig
and the Red center line stop for the lower (female) stripping jigs.
Pronged and Regular T-NutFor mounting Bobst cutting dies and portions of the stripping jig.
Available in any size.
Common sizes: 8/32, 10/24, 10/32, 1/4, 5/16 and metric sizes 4mm,
5mm, 8mm.
Quantities of 100 & 500 per box.
Aluminum ScoreOffers ease of application along with the ability to achieve score
profiles unavailable in steel. Mounts easily with National Air
Tacker.
Available .220” 3 point Shoulder Profile, .260” 3 point
Shoulder Profile
Other sizes and styles available with minimum order
Tie RodsUse Tie Rods/Tie Bolts to Clamp the wooden board to the pull
out frame on Bobst Diecutters
Non-Threaded T-Nuts6.75mm
For corrugated Bobst dies and stripping jigs
Channel Lock Rule PullersNarrow Jaw Economy rule puller from Channel.
Available lengths: 10”, 12”
Standard Channel Lock Economy Rule Puller.
Available lengths: 6”, 7”, 8”, 10”, 12” and 14”
Profile
Tru Fold Laser CreaseProvides accurate fold in the direction of the corrugation on heavy board, reduces
ropy scores, improves dimensional accuracy and reduces check ing in laminated label
applications. Tru Fold works with a bead formed on the 8 point head that provides an
accurate line score with a steel shoulder support.
Glue Flap Rule This rule enhances the adhesive’s effectiveness by
creating a porous surface on the flap or other surfaces
where glue will be applied. This perforating rule is 2
point thick with 1/32” x 1/32” perforated, medium wave
edge.
Designed to be used in creasing rule heights
-
8/18/2019 Manufacturing and type of Die Cutting
23/4823
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Stripping Solutions
Kori ClampEconomy rear clamps for female stripping jig. More cost
effective than metal clamps and other large plastic clamps. Fit
rails on existing and new stripping boards. So economical
there is no need to remove and re-use these clamps.
Stripping Pins & Blanker StandoffsFor use in stripping and blanking boards.
Benefits:
All pins have knurled bases for the greatest hold in the board
Smaller diameter pins are steel for durability
Larger diameter pins are light weight, economical aluminum
Manufactured in the USA exclusively for Advanced Die Supplies
Available:
Pointed: 1/8”, 3/16”, 1/4”
Flat: 1/8”, 3/16”, 1/4”, 5/16”, 3/8”
Blanker Standoff Pins: 7/8”, 1 3/8”, 1-1/4”
Flat Top and Crown Stripping Pins For use in stripping and blanking boards.
Available:
Flat: 2mm, 3mm, 4mm, 5mm, 6mm, 8mm, 10mm
Crown: 2mm, 3mm, 4mm, 5mm, 6mm, 8mm, 10mm
*All pins are beveled on bottom for easy fitting in dieboard and are
all a 4mm base.
Distance SpacerFor proper spacing of the male stripping board
Inner barrel heights available: 7/8” and 1
Die Storage BoltsBlack or Orange Storage Bolt for quick location of strip
ping tools
Available: 2” and 1-5/8” high
Stripping Plate3pt thick, 50mm high Stripping Plates for stripping boards. Pointed tips s
ejected scrap does not slip
________________________________________________ Thicknesses available: 5mm x 24mm, 7mm x 26mm, 9mm x 28mm
11mm x 30mm, 15mm x 36mm, 20mm x 39mm and, 25mm x 44mm
-
8/18/2019 Manufacturing and type of Die Cutting
24/4824
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Diemaking Solutions
MicroNik Use anywhere nicks are necessary especially at the lead edge and for greater sheet
stability, use in line with gripper fingers. A distributed pattern of nearly invisible
nicks creates a cumulative hold far greater than that of standard handnicked sec-
tions.
Benefits:
Improves stripping and blanking while reducing flaking and dusting.
Improves productivity in tool-making and on press.
Standard configuration:
2 point .918” and .937”
4 to 8 nicks per inch
nicks are 0.007” wide and 0.030”deep
42° bevel with chamfered baseOther sizes and configurations available.
MicroTrak This revolutionary Corrugated Creasing Aid works with a corrugated
effect on the face of standard creasing rules. The small, smooth bumps
break up the surface of the creasing face to simultaneously create
creasing pressure and relief.
Benefits:
Unique method reduces fiber and score cracking
Reduces the pressure necessary to crease
Improves the effectiveness and accuracy of the score line
Improves sheet stability and dimensional accuracy.
Available:
2, 3 and 4 point
Curved and straight standard Iengths
Other sizes car be special ordered
MicroPerf Ideally suited for perforating forms, continuous letterheads, checks, labels, cou-
pons and other single parts on thin stock products.
Available in: 2 point .750”, .918” and .937” high.
Tooth patterns available: 30, 40, 50, 60 and 70 TPI (teeth per inch)
MicroMaxMicroMax’s 2 point perf rule has a 0.020” deep square teeth with a 21° bevel to
minimize material displacement. Ideal for perforating multi-part forms, card
stock, packaging materials and other heavy weight stock.
Available in 2 point .918”, .937” and .938” high
Tooth patterns available: 30, 40, 50, 60, 70 and 100 TPI
-
8/18/2019 Manufacturing and type of Die Cutting
25/4825
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Marbach Die Making Solutions
Your advantages using the Mpower Technology The Mpower technology will provide you with significant advantages optimizing your
cutting process:
- Significant reduction of your make-ready timesFor you, this means an increase of your production capacity. Consequently your production will be more flexible
and you will be able to meet the requested delivery dates of your customers much better.
- Considerably higher lifetimeDue to the fact that the Mpower cutting rule is able to work under higher pressure than a conventional cutting
rule the lifetime of the Mpower rule is longer. This is very important for you both for long runs and for frequent re-
peat orders. Because not only the number of sheets you cut damages the k nife but rather the number of set ups.
- No swarf under normal conditions. The radius at the tip of the rule avoids a destruction in this area. Thecreation of swarf is thereby prevented and the palette of
blanks is absolutely free of fuzz.
Marbach blanking tool lightblanker – (#1) The best solution for a perfect blank separation of low runs
Your advantages using the marbapusher: (#2)universally useable => no capital commitment
• quickly exchangeable
• space-saving storage
• no screwing required
• high contact pressure
• reliable production process
• higher machine speed
(#1) (#2)
Marbanicker. This Nicker has a retractable weighted top that when dropped creates
a 0.1mm thick nick each time. The Chisels are replaceable and can be
flipped around when one side wears.
-
8/18/2019 Manufacturing and type of Die Cutting
26/4826
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Blanking Solutions
Adhesive Runners
( 5.0 x 3.0 x 2700mm)
( 6.0 x 3.0 x 2700mm)
( 8.0 x 3.0 x 2700mm)
____________________
Support Rail - Flat Top ToolsFor; 102,103,104-ER, 130-ER, 142-CER, 142-ER, 162-CER, Sprintera 106-PER, Sprintera
145-PER
______________________________________________________________________
JOGGER-UNIVERSAL -7/16” DROPGUIDE
SUPPORT RAIL - FLAT TOP TOOL 130-ER
SUPPORT RAIL END
SPECIAL LOW HEADSHCS M5X20mm
FLAT SHCSM3X25mm
UNIVERSAL MOUNT-
ING RAIL - 130
(950mm)
JOGGER-UNIVERSAL
SIDE
QUICK LOCK KIT
SPECIAL LOW HEAD SHCSM5X24mm
ACCESSORY NUT
3.5 x 28mm HARDENED PIN
PIN INSERTION GUIDE TOOL - FOR SUPPORTRAILS
BSI FRAME KIT -SP-130- ER
JOGGER - NARROW MOUNTINGRAIL - SIDE
PARALLEL CLAMP A D H E
S I V E S
P A C E R -
. 3 1 2 ”
R A I L
STANDARD-SHCSM5X20mm
JOGGER-UNIVERSAL-FRONT/REAR
MOUNTINGRAIL - NARROW-130 (877mm)
S T A N D
A R D -
S H C S
M 5 X 1
6 m m
SpeedBarRevolutionary new presser bar designed to make manufacturing and
operating male blankers less complex and less time consuming.
Benefits:
Press ready - no assembly required
No height adjustments
Jam free
Tested up to 16,000 SPH
Standard lengths fit any press size
Easy installation - only requires a drill
Compatible to Bobst Quick Lock
Less costly than alternative models
Available: 9’, 13”and 16”
-
8/18/2019 Manufacturing and type of Die Cutting
27/4827
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Blanking Solutions
Old Style Tower Presser
_________________________________________________________________
Standard Tower Presser & Flush Presser
________________________________________________________
JoggersJoggers for grid tools, front and rear, with hat, long slides. Side joggers.
Universal Joggers. For blanker dies. Reliable, light weight, economic, and
dependable.
____________________________________________________________
BSI Flat Top Tool KitsFor; Sp-102-CER, SP-103-ER, SP-
104-ER, SP-106-PER/LER, SP-130-ER
SP-142-CER, SP-142-ER, SP-145-PER
SP-162-CER.
BSI Frame KitFor; Sp-102-CER, SP-103-ER, SP-
104-ER, SP-130-ER, SP-142-CER,
SP-1600-ER, SP-162-CER, SPrintera
145-PER
BSI Universal Tool kitFor; Sp-102-CER, SP-103-ER, SP-104
ER, SP-106-PER / LER, SP-130-ER,
SP-142-CER, SP-142-ER, SP-145-PER
SP-162-CER
Presser RailPresser Rail
1.5” Blanker Stand Off
-
8/18/2019 Manufacturing and type of Die Cutting
28/4828
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
-
8/18/2019 Manufacturing and type of Die Cutting
29/4829
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Steel Rule
Helmold Bevel Guide National Steel Rule Bevel Guide
Advanced Die Supplies is proud to carry the following steel rule
Steel Rule featured by manufacturer on
the following pages...
Creasing RuleHard Crease is 60-70 temper.
Soft crease is 35 temper. Best suited for use in block dies or where rule can be easily inserted.
Soft crease can bend or de form if not correctly inserted. Both hardnesses are available with a tra-
ditional profile: ellipitical top and flat bottom as well as a dual elliptical profile. The dual elliptical
rule has a radius which is twice the rule thickness. This shape allows either edge to be used for
scoring, produces well defined scores without cracking and will not splinter wood.
A.
B.
C.
D.
E.
2 PT STD
3 PT STD
4 PT STD
6 PT STD
8 PT STD
DOUBLE RADIUS
DOUBLE RADIUS
1 RADIUS
1 RADIUS
1 RADIUS
60°
Center Bevel
52°
Center Bevel
42°
Center Bevel
Center Face
Double Bevel
Side Bevel Side Face
Double Bevel
60°
Center Face
Center Face
Long Bevel
Side Face Side Face
Long Bevel
A. B. C. D. E.
Lead Spacers
Available:
.5, 1, 1.5,2,3,4 and 6 point thick
5/8”(.625”) and 3/4”(.750”) high
Standard Creasing Rule Profiles
-
8/18/2019 Manufacturing and type of Die Cutting
30/4830
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Equipment
Single Miter MachineEasily miters cutting rule to guarantee that the rule
edges meet and no die cut material is left hanging.
Works for all thickness of rule.
Shims for different heights rule are necessary.
Side GaugeStandard Side Gauge used to set l engths for repetitive cuts, notches or bends.
Side Gauge for finer adjustments. May be adjusted to 0.0001” as a final
adjustment when setting up your bending, notching, cutting or miter machines.
Please specify the type of machine it will be used on.
Rule Cutter - Standard or PneumaticThis high performance Helmold Classic is now available in standard or pneumatic, power-assisted
configuration.
Both are designed to accurately cut steel rule to length.
Features:
Cuts up to 6 point tempered steel rule
Equipped with front and rear guages graduated by sixteenths
Short front gauge allows a cut up to 6”
Back long gauge allows a cut up to 24”
Knives are easily removed for sharpening
Available cutting heights: 1-1/2”, 2-1/8”, 2-7/8”
* For Die Benders and other Die Bending equipment, please visit our website www.AdvancedDieSupplies.com
Standard Bender for 2 and 3 pt. Rule.
The Helmold Standard Bender is practically in use wherever steel rule dies
are made. It uses interchangeable male and female dies to form rule into the
desired shapes without disturbing bends previously made.
The Helmold Standard Bender is equipped with an adjustable stop that can be set
in an instant, limiting movement of the dies and enabling the user to readily make
duplicate symmetrical bends. An adjustable gauge is also included that can be used
on either side of the bender for locating the position of rule relative to the dies.
This is an excellent starter tool for making simple bends; and a great second machinefor simple set bending operations. If your die room does “production set bending”
where two machines are needed to make a shape, this machine is a good choice to
back up a Bender Bendall. The Standard Bender is designed for use with rule up to 1”
in height. Shipping weight is 65 lbs.
* Heavy Duty Bender also available for 3 & 4 pt. rule.
The Standard Notcher for 2 pt. Rule
The Helmold Standard Notcher is used for notching or bridging rule. Having this
notcher handy in your die rooms will save you valuable time again and again.
The Standard Notcher is equipped with an adjustable link that allows male knives to
be re-set and adjusted after sharpening.
Standard notch sizes for this tool are 1/4” x 5/8,” and 5/16” x 3/4”.
Special sizes can be made to order. This is an excellent starter tool for any die
room; and a great second machine when you have to notch large quantities of rule at
a time. The Standard Notcher is designed to easily notch 2 pt. rule and can also notch
rule up to 3 pt. thickness. Shipping weight is 55 lbs.
* Heavy Duty Notcher also available for 3 & 4 pt. rule.
Cutter Knives
TIP: Every die shop should have a spare set on
hand, to eliminate down time when dull knivesneed to be sent out for re-sharpening.
-
8/18/2019 Manufacturing and type of Die Cutting
31/4831
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Helmold Perforating & Microperforating Rule
Common Perf Patterns
For the business form and carton industries
Teeth per inch and decimal spacing
4 Tooth x .039” S (.211”x 0.39”) 4 Tooth x .046” S (.204” x 0.46”) 6 Tooth x .04O” S (.127 x 0.40”)
For the corrugated industry
Fractional tooth width and spacing
8 Tooth x .039” S (.86” x 0.39”) 9 Tooth x .032 S (.079” x 0.32”) 10 Tooth x .032” S (.068” x 0.32”)
12 Tooth x .039” S (.044” x 0.39”) 12 Tooth x .032” S (.051” x 0.32”)
1/16”Tooth x 1/16” S (.062” x .062”) 1/16”Tooth x 1/32” S (.062” x .031”)
1/4”Tooth x 1/16” S (.250” x 0.62”) 3/16”Tooth x 1/16” S (.187” x 0.62”) 3/8”Tooth x 1/2” S (.375” x 1.25”)
3/16”Tooth x 3/32” S (.187”x .093”) 1/8”Tooth x 1/16”” S (.125” x .062”) 1/8”Tooth x 1/8” S (.125”x .125”)
-
8/18/2019 Manufacturing and type of Die Cutting
32/4832
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Zimmer Perforating Rule
Combination Cut-Crease Rule
Provides a cost effective solution when the die
requires alternating cuts and creases.
Available in 1-1/2, 2, 3 and 4 point in all standardheights.
3 Tooth x .032”(.301”or 7.65mm x 0.81 mm) 10% of Hold
4 Tooth x .032’’(.218”x 0.32”or 5.54 mm x 81 mm) 13% of Hold
4 Tooth x .060” (.190”x .060”or 4.83 mm x 1.52 mm) 24% of Hold
5 Tooth x .037”(.168”x .032”or 4.27 mm x 0.81 mm) 16% of Hold
6 Tooth x .032”(.135”x .032”or 3.43 mm x 0.81 mm) 19% of Hold
6 Tooth x .050”(.117”x .050”or 2.97 mm x 1.27 mm) 30% of Hold
7 Tooth x .032”(.111 x .032”or 2.82 mm x 0.81 mm) 22% of Hold
8 Tooth x .032”(.093”x .032”or 2.36 mm x 0.81 mm) 26% of Hold
8 Tooth x .050”(.075”x 0.50”or 1.91 mm x 1.27 mm) 40% of Hold
9 Tooth x .032”(.079”x 0.32”or 2.01 mm x 0.81 mm) 29% of Hold
10 Tooth x .032”(.068”x 0.32”or 1.73 mm x 0.81 mm) 32% of Hold
11 Tooth x .032”(.059”x 0.32”or 1.50 mm x 0.81 mm) 35% of Hold
12 Tooth X .032”(.051 x 0.32”or 1.30 mm x 0.81mm) 39% of Hold
14 Tooth x .032”(.039”x 0.32”or 0.99 mm x 0.81mm) 45% of Hold
16 Tooth x .032”(.031”x 0.32”or 0.79 mm x 0.81 mm) 51% of Hold
17 Tooth x .032”(.027”x 0.32”or 0.69 mm x 0.81 mm) 54% of Hold
-
8/18/2019 Manufacturing and type of Die Cutting
33/4833
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
National Steel Rule Edge Wave Rule
Helmold Full Body Wave Rule
Wave RuleWave rule has a wide range of applications, from cutting safety edges on cartons to
avoid hand injuries, to the deckle edge for greeting cards. Our Wave Rule comes with
an edge-only wave for faster and easier insertion.
Wave rule reduces dust and combats sharp edges on the diecut blank; instead the
diecut blank has a medium wave that acts as a safety edge.
SUPER FINE WAVE
MICRO FINE WAVE
EXTRA FINE WAVE
FINE WAVE
MEDIUM FINE WAVE
MEDIUM
STANDARD
MEDIUM COARSE
COARSE
EXTRA COARSE
7/16 PITCH
1/2 PITCH
1.5 pt.
1.5 pt.
1.5 pt.
2 pt.
2 pt.
2 pt.
2 pt.
2 pt.
2 pt.
2 pt.
1.5 pt.
2 pt., 3 pt.
Fine Angle
Medium Angle
Coarse Angle
Extra Fine Angle Hard Temper
Extra Fine Angle Sof t Temper
Fine Angle
Medium Angle
Coarse Angle
Deckle Edge
Scalloped Wave (Specify centerto center distance and depthof scallops.)
Close Wave (Available with 1/64”or 1/32”slot.)
Corrugated Edge, Flat Body
Profile Thickness Description
-
8/18/2019 Manufacturing and type of Die Cutting
34/4834
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Steel Rule-2
Zipper Rule Tear edge rule is used to produce easy-to-open packaging. Available in standard
and serrated style for flat and rotary dies. Tear Edge is sold in matching right and left
hand sets.
Also available notched or curved in standard diameters.
Helmold Full body Tear Edge Rule
National Steel Rule Tear Edge Rule
-
8/18/2019 Manufacturing and type of Die Cutting
35/4835
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
National Steel Rule
Euro-Cut® Rotary RuleBenefits:
Requires less pressure to cut
Improves die life by reducing wear on rubber
Improves stripping
Reduces edge crush
Allows faster running speeds
Available: 8TPI and 10TPI
Specify flat or curved
Klean Kut Rotary RuleBenefits of 8TPI:
Minimizes edge crush on the heaviest board
Improves stripping
Made from harder Alloy Steel
Benefits of 10TPI:
Excellent bendability
Cuts with very low pressure
Great for all board types
Especially good as lead and trail knife
Reduces anvil wear
Benefits of 13TPI:
Multi-purpose rule for plastics, micro-flutes and
fibrous material
Shallower gullet improves anvil life
Edge hardened for better wear
Standard rotary hardness for bendability
Leaves a smooth edge on products
Specify flat or curved
Prism Rotary RuleBenefits:
Longer bevel for improved release
Edge hardened for longer life
Reduces edge crush
Good for medium to heavy board grades
Leaves medium wave on the diecut blank
for “safety edge”
Available:
8TPI and 10TPI
2,3,4, 6 and 8 point
Specify flat or curved
Nataloy Cutting RuleNational’s exclusive alloy formulation results in a
rule that has medium bendability yet wears like
medium hard.
Available: 2, 3 and 4 point from .375” to 1.250” high
-
8/18/2019 Manufacturing and type of Die Cutting
36/4836
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
National Steel Rule
Stripper Rule & Trim StripDesigned to be used to construct a male stripping board out of laser burned or jigged
dieboard. The waved edge increases surface contact with the waste. A complete male
board can be constructed with Stripper Rule, or i t can be used in selective areas such
as slots.
Available:
2” high
Fine to Extra Coarse Wave
Trim Strip comes with pin-points every 5 mm
Rotary Wave RuleA National exclusive, Rotary Wave Rule is designed to provide a more aesthetic
appearance on displays run on a rotary press. Rotary Wave can be used to leave a
safety edge on blanks that will be hand-assembled.
Rotary Perforating RuleUsed as perforating rule for folding, holding blanks together or as a tear rule. Use serrated
perforating rule when the tooth of the per f exceeds 3/8”. Standard gullet depth is 3/16”.
Available on request, gullets up to 1/8”.
No Notch Curved RuleCurved rule with no back notch. Works well in places where a solid rule will add strength.
Available:
Diameters 11” and up
Rotary Punches
Designed to cut cleanly through all board grades. NationalRotary punches are serrated with 8TPI, 12TPI, Shallow
Profile or Klean Kut tooth configuration.
Available:
With inside or center bevel
Standard heights . 990”and 1.030”
Cut size diameter 3/16” - 1-1/4”
Other heights and outside bevel available on special orderOutside Bevel Center Bevel Inside Bevel
-
8/18/2019 Manufacturing and type of Die Cutting
37/4837
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
National Steel Rule
Laser CreaseNational’s Laser Crease is engineered to save time and money in t wo
ways. First, Laser Crease enables you to burn or jig dieboard faster by
eliminating the need to cut thicker lines when wider scores are needed.
Laser Crease also allows you to alter the width of the score without
having to go back and recut a line.
Standard Laser Crease
Standard Profiles
A. 3 ON 2 STD RADIUS TOP
B. 4 ON 2 STD RADIUS TOP
C. 4 ON 3 STD RADIUS TOP
D. 6 ON 3 STD CROWN TOP
E. 8 ON 3 STD CROWN TOP
F. 6 ON 4 STD CROWN TOP
G. 8 ON 4 STD CROWN TOPNational Steel Rule Tear Edge Rule
A. B. C. D. E. F. G.
10 TPI PRISM STD 10TPI 10 TPI
KLEAN KUT
11 TPI STD 12 TPI 13TPI
DEEP V
STD 8 TPI
8TPI PRISM
8TPI DEEP V 8 TPI KLEAN KUT 13 TPI
KLEAN KUT
16 TPI 20 TPI
EUR0-CUT or SST STD SCALLOP SHALLOW PROFILE N250 SCALLOP N500 SCALLOP 5 TPI
6 TPI 4.6 TPI 2.7 TPI
-
8/18/2019 Manufacturing and type of Die Cutting
38/4838
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Zimmer Steel Rule
Forme CutBenefits:
Minimizes edge crush
Improves stripping
Extends blanket life
Excellent bendability
Edge hardened profile
Available:
Curved or flat
8TPI and 10TPI
Non SymmetricalZimmer pioneered the non-symmetrical bevel for serrated steel rule.
This product is the result of many years of testing and development and
is proven to perform.
Benefits:
Cuts with minimal pressure
Reduces edge crush
Excellent bendability
Available:
8TPI, 1OTPI and 13TPI
Curved or flat
Scalloped ProfileBenefits:
Creates a clean, scalloped edge on corrugated or synthetic material
Scalloped edge acts as a safety edge
Extremely durable profile
Solution for diecutting problem material
Available:
Curved or flat
QC100Benefits:
Extraordinary knife for cutting or per forating
Exceptional value
Recommended for cutting plastic, synthetics, foam and tear-resistant material
Standard Serrated8 TPI Benefits:
Good for cutting heavier board
10 TPI Benefits:
Versatile rule for cutting across and around the cylinder
12 TPI Benefits:
Traditional tooth configuration for rotary diecutting
16 TPI Benefits:
Fine tooth configuration creates a finer edge finish
20 TPI Benefits.·
Good for micro-flute board
All Standard Serrated are available.
Curved or flat
Shallow ProfileBenefits:
Substantially reduces pressure
Excellent for cutting plastic corrugateRecommended for cutting plastic, rubber and textiles with minimal
penetration
Available:
14TPI
Curved or flat
-
8/18/2019 Manufacturing and type of Die Cutting
39/4839
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Punches
Every punch is case-hardened to a depth of 0.003”to 0.005” and a
nominal Rockwell hardness of Rc 60-62. Deep case -hardened and tempered
power punches are also available for heavy duty applications. We stock a wide
variety of standard cutting sizes from 1/32” to 2-63/64” and from .918” to 1.500” high.
Standard Tube Punches
Standard heights: .918”, .923”, .937”and 1”
Other heights available upon request.
Available with or without springs or Punch Rubba
Side Outlet Punches These punches pick up the slug and feed it through the side
of the punch. This self-stripping feature eliminates the need
to hand strip.
Available:
With or without a knurled base
Standard hardness or tool steel for difficult applications
With or without a relieved shoulder
Standard heights: .918”, 923”; .937”, 1”
Non-standard heights: 1.125”, 1.250”, 1.500”, 2.000”
Available cut diameter:
1/16” 19/32” in increments of 1/64”
Inside Bevel Center Bevel Outside Bevel
Center Bevel
Available cut diameter:
1/16” to 3” in increments of 1/16”
Inside Bevel
Available cut diameter:
5/64” to 3” in increments of 1/64”
Outside Bevel
Available cut diameter:
1/32” to 3” in increments of 1/64”
Straight Wall Punches These punches have the same size cutting edge and tube diameter.
Use them to give the straightest possible cut or when space is a factor
in the die. They are deep case hardened for added strength.
Available cut diameter: 3/64” to 3” in increments of 1/64”
Cup Punches These punches are made from a solid steel rod.
They are used when additional strength is required.
Available with inside, center or outside bevel
Available cut diameter:
1/32”- 31/64” in increments of 1/64”
-
8/18/2019 Manufacturing and type of Die Cutting
40/4840
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Latex & Cyanoacrylate Adhesives
Clean StripLatex Adhesive designed for rubbering flat
dies. Holds strong and strips away clean for
fast, easy re-rubbering.
Available in 1 gallon containers.
Special order other sizes.
Super Glue (Cyanoacrylate)2001C and 2075C are fast setting, high viscosity adhesives for bonding a variety of
materials such as wood, cork and leather as well as most metals, rubbers, and plastics.
2001C and 2075C have outstanding flexibility and enable use when high impact
resistance or gap fill is required.
Slow Setting 2075C curing time:Rubber to wood - 7 seconds
Plastic to plastic - 8 seconds
Metal to metal - 20 seconds
Fast Setting 2001C curing time:Rubber to wood - 3 seconds
Plastic to plastic - 6 seconds
Metal to metal - 15 seconds
Dispenser Bottles2 oz. bottles
AC45 ActivatorAids super glue adhesion by penetrating the surface
to be bonded and accelerating the hold and set time. Debonder AC68Debonder “undo” AC68 Cyanoacrylate (Super Glue)
adhesive remover quickly softens and dissolves cured
and uncured adhesive from unwanted areas.
Use this to clean hands and other surfaces.
It is an essential product for industrial manufacturing
production involving the use of cyanoacrylates.
Air Stripping Hammers & Chisel SetUsing a pneumatic stripping hammer is fastest way to strip loads off press. Ingersol
Rand,
high quality air hammer is available with options such as counter balancers, air input
Waste Stripper
Unique in the market, the
BOBST waste stripper provides
400 watts of output power to
strip waste efficiently, is easy
to hande and is low noise at 87
db. Strips edge waste 10 times
faster than by hand!
Finishing
-
8/18/2019 Manufacturing and type of Die Cutting
41/4841
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Tape & Spray Adhesives
3M® ATG GunFor application of adhesive transfer gum in finishing and sample mak ing.
Double Faced TapeMultiple applications. Most common application for adhering counterboard to
cutting plate
Available: 2” - 12” wide
Reinforced Filament Tape
Available: 1/4” – 4” wide
3M Scotch ATG TapeClear adhesive transfer gum used for finishing and sample
making.
Available: 1/4”’and 1/2” wide
36 yards long
Masking Tape
Available: 1/4” - 4”
3M 77 Spray The spray adhesive most used to adhere
phenolic counter material to Cutting plates
High strength, fine mist adhesive
High tack bond for many substrates including
metal, plastics, rubber and wood
Long open time and uniform spray pattern
provides faster application with less waste
Tip: Especially helpful in adhering paper labels
to shrinkwrapped pallets
Flatback Sealing TapeExtra tacky sealing tape.
Available: 1/4” – 4” wide
-
8/18/2019 Manufacturing and type of Die Cutting
42/4842
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Ejection Material
KO-18
K-10
K-2G
K-1
KO-11
KO-2B
KO-3
KO-15
Black Bear
DuraStrip
K-9Cork
K-14Cork
RedRhino
GreenG’rilla
GumRubber
Open CellExtra Firm DensityHeights from 1/4” - 3/8”
Open CellFirm DensityHeights from 3/16”- 5/8”
Open CellExtra Firm DensityHeights from 1/4”- 5/8”
Open CellExtra FirmDensityHeights from 1/8”- 5/8”
Open CellFirm DensityHeights from 3/8” - 5/8”
Open CellMedium DensityHeights from 1/4” - 5/8”
Open CellMedium DensityHeights from 1/8” - 1”
Closed CellMedium-SoftDensityHeights from 3/16”- 1”
Closed CellMedium-SoftDensityHeights from /16”- 1”
Micro-CellExtra FirmDensityHeights from 1/8”- 11/16”
Cork-RubberCombinationExtra FirmDensityHeights from 1/16”-5/8”
Cork-RubberCombinationMedium-FirmDensityHeights from 1/4” - 3/8”
Micro-CellPremium FirmDensityHeights from 1/4”- 1”
Micro-CellExtra-FirmDensityHeights from ¼”- 5/8”
Closed CellFirm DensityHeights from 3/8” -9/16”Widths from 1/32”-1/4”
Versatile rubber recommended for useon Bobst® and other high speed presses for foldingcarton, micro-flutes, labels and gaskets
Primarily for high speed presses for folding carton,gaskets and labels
Versatile rubber used in general diecutting,carton and corrugated applications
Primarily for high speed presses for folding carton,micro-flutes, labels and gaskets
Used for folding carton, micro-flutesand standard corrugated
Primarily for letterpress; versatile enough to usein paper, carton or corrugated applications
Used for solid fibers and cartons; generalapplications including folding carton
Primarily for corrugated dies, both flat and rotary
Affordable, long lasting, GRIZZ Microcell rubber.
Low transverse expansion and firm durometermake this rubber excel in corrugated slats,punches and as trim breakers
The combination of rubber and cork makethis ejection material ext remely durable andresistant; used on both letterpress and highspeed presses
The combination of rubber and corkmake this ejection materia l extremelydurable and resistant; used on bothletterpress and high speed presses
Versatile performance suitable for mosthigh speed applications
Primarily used in high spend applications for bothcorrugated and folding carton; excellent slotejector Scalloped or Straight
Designed for use in folding carton slots
• Sheets, strips & blocks• Regular or with PSA*• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA*• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA*• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA*• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA*• Special proles: Sidewave, Trap Cut
• Regular or with PSA*• Sheets, strips & blocks• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA• Special proles: Sidewave, Trap Cut
• Sheets, strips & blocks• Regular or with PSA• Special proles:
• Sheets, strips & blocks• Special proles: scalloped or straight
• Sheets, strips & blocks• Regular or with PSA
• Sheets, strips & blocks• Regular or with PSA
• Sheets, strips & blocks• Regular, PSA*• Special proles: Ejecto-Flex E-Z-Set, Side-Wave
• Sheets, strips, blocks & Pads• Regular, PSA*• Special proles: Ejecto-Flex E-Z-Set, Side-Wave, Scalloped and Groovy G’rilla Slot cut
• Sheets and Strips• Special Proles: Rick Rack Scalloped
Features Applications Available
-
8/18/2019 Manufacturing and type of Die Cutting
43/4843
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
Specialty Ejection Material
BOBST manufactures a vast range of ejector rubbers
to cope with any production situation that the modern die
maker might encounter.
• Use of Euro Rubba© for cartons
• Rainbow Rubber© for high speed platens
• Slot Rubba© for rapid ejection between rules
• Easi-Crease© for fracture-free corrugated
• Flexi-Crease© for high speed corrugated
• New C-prole for reduced nicking
• All produced to ISO 9002
Special ProfilesMaxPoint™
E jecto-FIex™
E-Z-Set™
SideWave™
Scalloped
The GRIZZ line of microcell rubber is affordable, long lasting and gives you a great
return on your investment!
Thicknesses available:
1/16”, 1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4”, 7/8” and 1”
-
8/18/2019 Manufacturing and type of Die Cutting
44/4844
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
D-Profile Euro Rubba The original “EuroRubba” for use at nicks to reduce
pulled nicks and flaking. Enables better and faster
sheet transfer.
Available 1/4” - 3/8” highGreen G’rillaEjection rubber designed for demanding slot and restricted
ejection areas.
Sizes: 1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 7/16”, 1/2”, 9/16”, 5/8”
Available:
Ejecto-Flex, E-Z-Set, Side-Wave,
Scalloped or Straight
PSA or regular
SuperBlue Stripping FoamExtra firm, resilient, stripping foam for heavy car ton and corrugated board. Stabilizes
blank during stripping process. Hardier and more economical than competitive foams.
Standard size: 1-5/8” x 1-5/8” x 36”.
Special order other sizes.
Groovy G’rillaGrooved, wavy shape generates
required ejection force in slots while
allowing room for compression with no rule
deflection.
For slots widths: 1/8”, 3/16”, 1/4”, 5/16”, or 3/8”
Red RhinoFeatures & Benefits:
Most versatile ThermoPlastic rubber
Increase press speed
Will not crush the product
Will not overload the press
Quick kick for ejecting thin substrates with the
compressibility needed to
handle thicker substrates
Life expectancy of over 1,000,000 cycles at
50% compression
0. 020”thickness tolerance
Available in:
Sheets, strips & blocks
Regular PSA*and Super Sticky PSA
Ejecto-Flex, E-Z-Set, Side-Wave
Gray Economy FoamStripping foam for light weight paper
and board.
Standard Size: 1-1/2” x 1-3/4” x 3”
Special order other sizes.
Sprint RubbaNew profile shape designed in conjunction with the Bobst Group for use on the high-
est speed presses. For use at lead edge and at nicks. Unique shape reduces the number
of nicks necessary. Also combats dusting, fragmentation and angel hair.
Benefits
Wider flat top profile to avoid board bruising
Concave base for greatest stability
Material is white to avoid mark ing board
Available: 1/4”- 3/8”high
-
8/18/2019 Manufacturing and type of Die Cutting
45/4845
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
MONROE RUBBER
FunctionalRangeofMotion
The only moving parts on a cutting dieare the ejection materials.
As with any moving mechanical or compressiblepart, there is a maximum functional range of motion.
Once that range is exceeded, the item no longerfunctions properly, which will lead to failure.
The chart above shows the maximum funtionalrange of motion in green for each product. Once thefunctional range is exceeded it enters the yellowdensifcation point where the rubber becomes asolid, and can no longer compress. Go beyond thispoint and the rubber will fail and break apart. For theejection rubber to work properly, it must remain withinthe green functional range of motion.
-
8/18/2019 Manufacturing and type of Die Cutting
46/4846
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
www.AdvancedDieSupplies.com [email protected]
Dura-Strip This low transverse expansion rubber is highly stable, durable, heat resistant and con-
sistent. This micro-cellular elastomer is proven on both rotary and flat dies. Available
for slots, trim breaker rubber and for punch ejector.
Available heights, Scalloped: 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”
Straight: 1/4”, 5/16”, 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”
Color CreaseColor-coded corrugated creasing aid. Designed to reduce board damage in poor
quality board.
Benefits:
Color-coded for easy, accurate use
New improved shape
Radical base provides total stability of rubber on the dieboard
Resistant to heat and UV degredation
Self-lubricating to reduce board friction
Available heights and colors:
Kushion KreaseDesigned to reduce fractured scores common in dry or recycled board. Gentle crush-
ing action allows the scoring rule to form an accurate line crease on all grades of
corrugated. Use .035” below the scoring rule.
Available:
.175”, .200”, .225”, .250”, .275”, .295”, .300”, .315”, .325”, .335”, .355”, .370”, .380”, .395”
Specify box or coil
BROWN
RED
GRAY
YELLOW
GREEN
GOLD
BLUE
PURPLE
ORANGE
WHITE
PINK
BLACK
BEIGE
.177
.197
.224
.256
.276
.295
.325
.335
.354
.374
.394
.421
.433
4.5 mm
5.0 mm
5.7 mm
6.5 mm
7.0 mm
7.5 mm
8.0 mm
8.5 mm
9.0 mm
9.5 mm
10.0 mm
10.7 mm
11.0 mm
Thousandths Millimeters
-
8/18/2019 Manufacturing and type of Die Cutting
47/4847
ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES ADVANCED DIE SUPPLIES
Eastern Regional Office (866) 343-7757Pacific Regional Office (800) 600-0181
3M 77 Adhesive Spray 41
3M ATG Gun 41
3M Tape 41
Activator 40
Adhesive Spray 41
Adhesives 41
Adhesive Runners 26
Adjusto Guides 19
Adjustable Score 4
Air Stripping Hammer 40
Aluminum Score 22
Aluminum Stripper 40
Apron 17
Arbor 21
Back Up Plates 16
Bench Press, Matrix 16
Black Grizz 43
Blanking Accessories 27
Blanker Standoffs 23
Bobst ® Cutting Plates 16
Bolts 23
BSI Parts 27
BSI Workstation/Frame Stand 27
Carbon Paper 16
C