Manual for HotSpot Printer

Table of Contents

1. Buttons..................................................................................................................22. Menu structure...................................................................................................................43. Configuration description .................................................................................................84. Installing new software........................................................................................105. Set time and date................................................................................................126. Restore to default setting....................................................................................13

1. Buttons

1. Printer Power on/off switch2. Menu navigation – (up /down)3. Paper feed4. Printer Main Menu Display5. Character size change in text input mode (switch between capitals and small

letters), other specific options6. Iterate between different alphanumeric characters, not directly accesible on keypad7. Confirm button, used for setting saving or choosing options8. Clears text9. Exit from current menu or cancel configuration changes10. Alphanumeric buttons

2. Menu structure

1. AP config

Wireless network configuration which will be used by the printer.

1A. Scan

Start searching for accesible WiFi networks. Here it's possible to select desired network used by Printer.

1B. SSID

It's possible here to manually enter desired wireless network name (SSID)

1C. Security

If WiFi network is secured, here it's possible to choose security type and enter required credentials (password)

2. IP Config

Printer IP address configuration

2A. DHCP

Standard way the Printer is configured is getting IP adress from DHCP server.If IP address of Printer should be configured manually it's required to press ENTER here and follow through 2.B – 2.F

2B. IP

Enter manually IP Address

2C. MASK

Enter manually network mask

2D. GWAY

Enter network gateway

2E. DNS1

Enter IP address of primary DNS server

2F. DNS2

Enter IP address of secondary DNS server

3. MT Config

Printer access to Mikrotik device (HotSpot)

3A. MT IP

Enter IP of Mikrotik device

3B. User

Enter UserName used for singing in

3C. Password

Password for User entered in 3.B.

3D. Test

Printer will try to connect to Mikrotik device

4. Tariff Config

Tariff configuration, which willl be applied to HotSpot customers.

4A. Patterns

Common prefixes used by system.One is needed to recognize template records in Tariff section of Mikrotik configuration. The other one is used by system to prepending every username generated by printer with this string.

- „Pattern:” - string for tariff prefix- „User:” - string for user prefix

4B. Fetch Tariff

Using this option Printer will download template tariffs from Mikrotik device

4C. Change order

There is possible to change the order in which tariffs are displayed on the printer screen. Choose one tariff using navigation buttons (2), then press function button (5) and againg using (2) move seleted tariff to required position and press (5). Repeat this scenario to other tariffs as required. To confirm new order press Enter button (7) and when confirmation question is shown press it (7) again.

5. Custom config

In this section it's possible to define some custom setting like logo, header & footer printed on each ticket, and additionally access password for config section of Printer menu.Logo is a graphic file saved as monochromatic picture in BMP format. Maximum and recommended size of this picture is 384X192 pixels. Header & Footer are text files. All files can be downloaded from FTP server.

5A. FTP IP

Enter IP Address of FTP server

5B. User

User name used for FTP server access

5C. Password

Password used for FTP server access

5D. Charset

Charset code which should be used for header&footer printing.

5E. Download file

Option used for downloading each element form FTP server and storing in Printer internal memory. The proper name of each file must be provided.

5F. Show file

Display of each file downloaded form FTP – for veritication

5G. Delete file

Option used for deleting each file

5I. Menu PIN

Enter access password for printer menu (digits only).

3. Configuration description

In order to have Printer working with Mikrotik HotSpot, some configuration steps are required on Mikrotik side.

Configuration for Mikrotik:

1. User Manager package must be instaled.2. Start HotSpot Service3. API service must be Enabled: IP → Services → API4. If Printer will connect to Mikrotik HotSpot using the same WiFi network as

customers (HotSpot network), then MAC Address of the Printer should be added to the HotSpot IP Bindings: IP → HotSpot → IP Bindings to assure communictation with Mikrotik device.

Attention: Printer works in 802.11b mode only.

Configuration for HotSpot printer:

1. Press MENU button to enter into configuration menu 2. In AP CONFIG set the name of access point3. In IP CONFIG set IP address for HotSpot printer (default is DHCP)4. In MT CONFIG set IP Address and password from Mikrotik with installed

user manager5. In TARIFF CONFIG setup tariffs for HotSpot.

In UserManager setup a template user with appropriate tariff. They have to be disabled! (disable = yes). New user is created by copying permissions from template user. The name of every template user must start with the same word (as described in 4.A. Patterns section)

Some examples:

mytariff-hour, mytariff-day, mytariff-week

In 4.A. Patterns menu section set:

Patterns: mytariff

- in „User” set the name of user which will be created on HotSpot Printer

Example: „User”: user Created user is: user8948

In FETCH TARIFF menu the HotSpot Printer read the tariff (model user) from MikroTik user manager.

After this configuration you will see in main menu the tariffs from your HotSpot.

4. Installing new software

To installing a new software on the HotSpot printer you have to do following steps:

1. Connect Printer to PC using included serial cable2. Boot up HotSpot Printer and immediately press repeatedly MENU button to

enter Diagnostic Menu 3. On computer start InitTool software (you can it download from:

www.hotspot-printer.com)4. In InitTool software select COM port and set bautrate to 115200 (as shown

on picture below):

5. Press Refresh button to change the model of printer from unknown to NEW8110 (as shown on picture above)

6. Check APP option and select file with a new software for the printer and press Download button.

On status bar at bottom of InitTools software you will see Download Successfully and on printers screen you will see Send Appinfo, OK

7. Press Cancel (10) button on HotSpot Printer keypad to exit from Diagnostic MENU and start new firmware.

5. Set time and date

To set time adn date on the HotSpot printer you have to do following steps:

1. Boot up HotSpot Printer and immediately press repeatedly MENU (4) button to enter Diagnostic Menu

2. Press right menu navigation button (2)3. From menu select: 4-Set Time 4. Using only digits button write a new date and time in format:

YYMMDDHHMMSSafter the two digit for:

• YY – year• MM – month• DD – day• HH – hour• MM – minute• SS - second

5. Press enter (7) button to save the changes6. Press Cancel (10) button on HotSpot Printer keypad to exit from

Diagnostic MENU and start printer's firmware.

6. Restore to default setting

To installing a new software on the HotSpot printer you have to do following steps:

1. Connect Printer to PC using included serial cable2. Boot up HotSpot Printer and immediately press repeatedly MENU button to

enter Diagnostic Menu 3. On computer start InitTool software (you can it download from:

www.hotspot-printer.com)4. In InitTool software select COM port and set bautrate to 115200 (as shown

on picture below):

5. Press Refresh button to change the model of printer from unknown to NEW8110 (as shown on picture above)

6. In POS Information section click on Application Information, then

click on TLGMTPOS and press Delete button (as shown on picture below )

7. Now, you must load to the printer a new software. See section 4