Canon

SPEEDLITE

580EXII

III

INSTRUCTION MANUAL

MODE D'EMPLOI

MANUAL DE INSTRUCCIONES

Canon

SPEEDLITE

SBOEXII

I

Thank you for purchasing a Canon product.

The Canon Speedlite 580EX II is an EOS-dedicated, high-output flashunit automatically compatible with E-TTL II, E-TTL, and TTL autoflash.It can serve as an on-camera flash as well as a master unit or a slaveunit in a wireless, multiple-Speedlite system. It has the same dust- andwater-resistance as EOS-1 0 series cameras.

• Read this instruction manual while also referring to yourcamera's instruction manual.Before using the Speedlite, read this instruction manual and your camera'sinstruction manual to familiarize yourself with the Speedlite operations.

• The basic operation is as easy as with normal AE shooting.When the 580EX II is attached to an EOS camera, almost all automaticexposure control for flash photography is handled by the camera.It is almost the same as using the camera's built-in flash if it has one. You canthink of the 580EX II as a built-in, high-output flash, but attached externally.

• It becomes automatically compatible with the camera's flashmetering mode (E-TTL II, E-TTL, and TTL).In accordance with the camera's flash control system, the Speedlite controlsthe flash automatically in the respective flash metering mode:1. E-TTL II autoflash (evaluative flash metering with preflash reading/lens

distance information)2. E-TTL autoflash (evaluative flash metering with preflash reading)3. TTL autoflash (off-the-film metering for real-time flash metering)

Regarding the camera's available flash metering modes, refer to the"External Speedlite" specification in the "Specifications" of yourcamera's instruction manual.

The camera instruction manual's chapter on flash photography will referto cameras having flash metering modes 1 or 2 as a Type-A camera(compatible with E-TTL II or E-TTL). And cameras having flashmetering mode 3 (compatible with only TTL) are called Type-Bcameras.

* This instruction manual assumes that you are using the Speedlitewith a Type-A camera.For Type-B cameras, see page 55.

2

Contents I I II 111111 II 1

1 Getting Started and Basic Operation 7

2 Using Flash 13

3 Wireless Flash 33

4 Reference 47

Conventions Used in this Manual

• The < @ > symbol in the text refers to the Select Dial.The < @ > symbol in the text refers to the Select/Set button.

• The sm symbol in the text refers to a Custom Function.• The operation procedures in this instruction manual assume that both

the camera and Speedlite's power switches are ON.

• Icons used in the text to indicate the respective buttons, dials, andsettings match the same icons found on the camera and Speedlite.The (04 ) / (06) / (816) icons indicate that the respective functionremains in effect for 4 sec., 6 sec., or 16 sec. after you let go of thebutton.

• Reference page numbers are indicated by (p.**) .• ' This instruction manual uses the following alert symbols:

__ : The Caution symbol indicates a warning to prevent shootingproblems.

[]] : The Note symbol gives supplemental information.

3

Contacts

Nomenclature

Flash head/Wirelesstransmitter

Wireless sensor

(p.49)

Mounting foot (p.9)

Case

r

Contact cover

External powersource socket

-----~r~:~~~. ~t ~__'y\l]

PC terminal

Bracket mountinghole

Mini stand

4

Bounce angle

LCD panel

<MODE>-------­Flash modelSlave setting button I \ - <~H/~>(p.11, 22, 24/45, 46) '\ /' High-speed sync

~~g/p~~';,7i11Uminationl Ir=J -J--:~:~~~1~:~::::::nCustom Function setting \ ~ cover (p.8)button (p.6/27) BOn r~ZOOM/+z. '---Battery compartment

PILOT 0 0 ~ II irJ lock lever (p.8)

<PILOT> -----+---,~~OF\O~rJLPilot lamp/Test firing/ \ ~ 6) rn~1 <ZOOM/~>Wireless slavepow~r'J!l~ ~) )1. Zoom button/ON button (p.10/38) ~Ol"i(;~ Wireless selector/

~ ==~ Wireless set button

J ---7 (p.20/36, 39,40,41,42,45)Flash exposure ...----/confirmation lamp (p.11)

Mounting foot's Power switch (p.10)lock lever (p.9) < OFF> : Power off

<ON> : Power on

Lock-release button (p.9)

Dust- and water-resistantadapter

< @ > Select Dial

* < (!) > Select/Set button

[l] Asterisked buttons have functions which remain active for 8 sec. after youpress and let go of the button. The < :fr> illumination lasts for 12 sec.

5

LCD Panel

<ISO> ISO speed

Manual flash output levelFlash exposurecompensation amountFEB compensation amount

<~> High-speed sync(FP flash)

<~> FEB

< (i!J > Manual zoom

ApertureFEB statusStroboscopic flash countStroboscopic flash frequencyManual flash 1/3-stopincrement indicatorCustom Function No.Custom Function setting

Zoom focal length

<E/ETTL/TTL>lAuto externalmetering/ <~ > Auto zoomE-TTL (11)/ for image size

TTLautoflash rr ETlrL m-~:-(lj)--;';:IBBmm~~<EM> I"~~..!.. , n, ...!..'Manual external I L I aal.aau.aa I .a. Hz

metering JT~MlJLTI 3",~ · . ". I Slave IDCIII~"''Z.~ 1234~ 8:§':~

<M/MuLTI> S:1;-4:1~1-.-1:1~z;-:J:4• 1~8 I Slave IDManual flash/Multi ~..- - -~~-'_'_••_ ••-~I~1underscore(Stroboscopic) 0.5 0.7 1 1.. 1 2 3 4 6 9 13 18 mflash ~~ 2.3~_7_~~) 30 ~O 60 f~ Flash ratio

<C!D > Flash rangeCustom Function scale/Flash

ratio scale<~> Flash -------'exposure compensation

<~>----------'

Second-curtain sync

Firing mode ----------'Master flash ON: <~-.

Master flash OFF: <z.-'Slave flash : ~~

<~ > Flash bounce indicator(Blinks for 7 down)

Indicator(meters)

Indicator (feet)

<~> Flash ratio

<~>Slave

<o:m:mI > Master

<IDIII> Channel

• To illuminate the LCD panel, press the < :.t?:- > button .• The items actually displayed depend on the current settings.

6

Getting Started andBasic Operation

Installing the Batteries 8Attaching to the Camera......................................... 9Turning on the Power Switch................................ 10Fully Automatic Flash Shooting 11Using E-TTL II and E-TTL Autoflash in theShooting Modes.................................................... 12

__ Cautions for firing continuous flashes

• To avoid overheating and degrading the flashhead, do not fire more than 20 continuousflashes. After 20 continuous flashes, allow a resttime of at least 10 min.

• If you fire more than 20 continuous flashes andthen fire more flashes in short intervals, theinner overheating prevention function may beactivated to make the recycling time about 8 to20 sec. If this occurs, allow a rest time of about15 min. and the flash will then return to normal.

Installing the BatteriesInstall four size-AA batteries.

Open the cover.• Use your thumb to press the battery

compartment lock lever, then slide itas shown by the arrow CD to open thecover.

Install the batteries.• Make sure the + and - battery

contacts are properly oriented asshown in the compartment.

Close the cover.• Close the battery compartment cover

and slide it as shown by the arrow.~ When the cover clicks in place, it will

be locked.

Recycling Time and Flash Count (with size-AA alkaline batteries)

" on new• Quick flash enables a flash to be fired before flash-ready (p.1 0).

-- • Using size-AA batteries other than the alkaline type may cause improperbattery contact due to the irregular shape of the battery contacts.

• If you change the batteries after firing many flashes continuously, beaware that the batteries might be hot.

[i] Use a new set of four batteries of the same brand. When replacing thebatteries, replace all four at one time.Size-AA Ni-MH or lithium batteries can also be used.

8

Attaching to the Camera "I

Attach the Speedlite.• Slip the Speedlite's mounting foot into

the camera's hot shoe all the way.

Secure the Speedlite.• On the mounting foot, slide the lock

lever to the right...- When the lock lever clicks in place, it

will be locked.

Detach the Speedlite.• While pressing the lock-release

button, slide the lock lever to the leftand detach the Speedlite.

9

Turning on the Power Switch ,II 11111 III 1111 111111111111111

\1 Set the power switch to <ON>.l'" The flash recycling starts.

Check that the flash is ready.• The pilot lamp will first turn green (ready

for quick flash), then red (flash ready).Pressing the pilot lamp will fire a testflash.

About Quick Flash

Quick flash enables a flash to be fired before flash-ready, when the pilotlamp is still green.Although the Guide No. will be 1/6 to 1/2 that of the full output, quick flashis effective for near subjects and when you want a shorter recycle time.Set the drive mode to single shooting. Quick flash cannot be used in thecontinuous shooting, FEB, manual flash, and stroboscopic flash modes.

[IliI Quick flash can also be used during continuous flash shooting.(C.Fn-06 ~ p.27)

About Auto Power Off

To save battery power, the power will turn off automatically after acertain period (approx. 1.5 min. to 15 min.) of idle use. To turn on theSpeedlite again, press the camera's shutter button halfway. Or pressthe Speed lite's test firing button.

[IliI Auto Power Off can also be disabled. (C.Fn-01 ~ p.27)

[lJ • A test flash cannot be fired while the camera's operation timer 04 or 06is active.

• The Speedlite's settings will be retained in memory even after the poweris turned off. To retain the Speedlite's settings after you replace thebatteries, turn off the power and replace the batteries within 1 minute.

10

Fully Automatic Flash Shooting ••"\\\1\\"\1&\"."

When you set the camera's shooting mode to < P> (Program AE) or< 0 > (Full Auto), E-TTL II/E-TTL fully automatic flash will make it aseasy as normal AE shooting in the <P> and < 0 > modes.

TT Zoom 50mm Set the Speedlite to <ETTL>.Press the <MODE> button so that<ETTL> is displayed.

~ :;0 5.:; •

ETTL Zoom 50mmF- 5.6

-------0.50.7 1 1.5 2 3 4 6 9 13 18 m

Focus the subject.Press the shutter button halfway to focus.The shutter speed and aperture willbe displayed in the viewfinder.Check that the < ~ > icon is lit in theviewfinder.

Take the picture.Check that the subject is within theeffective range displayed on the LCDpanel.Right before the shot is taken, a preflashis fired, then the main flash is fired.If a standard flash exposure wasobtained, the flash exposure confirmationlamp will light for about 3 sec.

[i] < ETTL > will be displayed on the LCD panel even if the camera iscompatible with E-TTL II.

e If the flash exposure confirmation lamp does not light, move closer to thesubject and take the picture again. With a digital camera, you can alsoincrease the camera's ISO speed.

11

Using E-TTL II and E-TTL Autoflash in the Shooting Modes BI

Just set the camera's shooting mode to < Av > (aperture-priority AE),<Tv> (shutter-priority AE), or <M> (manual) and you can use E-TTL 11/E-TTL autoflash.

Select this mode when you want to set the shutter speed manually.The camera will then automatically set the aperture matching the shutter

Tvspeed to obtain a standard exposure.

\\\ If the aperture display blinks, it means that the background exposure willbe underexposed or overexposed. Adjust the shutter speed until theaperture display stops blinking.

Select this mode when you want to set the aperture manually.The camera will then automatically set the shutter speed matching theaperture to obtain a standard exposure.If the background is dark like a night scene, a slow sync speed will be usedto obtain a standard exposure of both the main subject and background.Standard exposure of the main subject is obtained with the flash, while astandard exposure of the background is obtained with a slow shutter speed.

\\\ Since a slow shutter speed will be used for low-light scenes, using atripod is recommended.

\\\ If the shutter speed display blinks, it means that the backgroundexposure will be underexposed or overexposed. Adjust the aperture untilthe shutter speed display stops blinking.

Select this mode if you want to set both the shutter speed and aperturemanually.

M Standard exposure of the main subject is obtained with the flash. Theexposure of the background is obtained with the shutter speed and aperturecombination you set.

\\\ If you use the < DEP > or < A·DEP > shooting mode, the result will be the same asusing the <P> (Program AE) mode.

Flash Sync Speeds and Apertures Used

P Set automatically (1/60 sec. - 1/X sec.)

Tv Set manually (30 sec. - 1IX sec.)

Av Set automatically (30 sec. - 1IX sec.)

M Set manually (bulb, 30 sec. - 1IX sec.)

1/X sec. is the camera's maximum flash sync speed.

12

Automatic

Automatic

Manual

Manual

Using Flash

~ Flash Exposure Compensation 14~ FEB 15FEL: FE Lock........................................................ 16

~ High-speed Sync............................................. 17Bounce Flash..... 18

ZOOM: Setting the Flash Coverage and Usingthe Wide Panel..................................................... 20

M: Manual Flash................................................. 22

MULTI: Stroboscopic Flash 24r::I> Second-Curtain Sync 26

C.Fn: Setting Custom Functions 27

External Flash Metering........................................ 30Speedlite Control with the Camera's MenuScreen 32

~ Flash Exposure Compensation l. 1111 II 111I LII

In the same way as normal exposure compensation, you can setexposure compensation for flash. The flash exposure compensationamount can be set up to ±3 stops in 1/3-stop increments. (If thecamera's exposure compensation is in 1/2-stop increments, flashexposure compensation will be in 1/2-stop increments.)

Select <~>.Press the < @ > button so that <~ >is displayed.The <~> icon and the flashexposure compensation amount willblink.

Set the flash exposurecompensation amount.~,~ Turn the <@ > dial to set the amount.~t To cancel the flash exposure

compensation, set the amount to"+0."

Press the < @ > button.Flash exposure compensation will beset.

[]] If flash exposure compensation has been set with both the Speedlite andcamera, the Speedlite's flash exposure compensation amount will overridethe camera's.

lID Setting the flash exposure compensation can be limited to only the <@>dial. (C.Fn-13 ~ p.27)

14

~ FEB ,1iI1I"1 i;;;11 11'11;;;11 lllii! 1'11,;;11 U'iliiU111 II 1I1111111~1

You can take three flash shots while automatically changing the flashoutput for each shot up to ±3 stops in 1/3-stop increments (1/2-stopincrements if the camera enables only 1/2-stop increments). This iscalled FEB (Flash Exposure Bracketing).

Select <~>.Press the <@> button so that <~>is displayed.The <~ > icon and bracketingamount will blink.

Set the flash exposure bracketingamount.• Turn the < @ > dial to set the amount.

Press the <@> button.FEB will be set.

III • After the three shots are taken, FEB will be cancelled automatically.For FEB, set the camera's drive mode to single shooting. Be sure theflash is ready before shooting .

• You can also combine FEB with flash exposure compensation and FElock.

[II'iI You can prevent the FEB from being cancelled automatically after thethree shots are taken. (C.Fn-03 ~ p.27)

[II'iI The FEB shooting sequence can be changed. (C.Fn-04 ~ p.27)

15

FEL: FE Lock III1III[ .. __

FE (flash exposure) lock locks the correct flash exposure setting for anypart of the scene.With < ETTL > displayed on the LCD panel, you press the camera's<FEL > button. If the camera does not have the <FEL > button, press the<*> button.

Focus the subject.

Press the <FEL> button. (816)Aim the subject at the center of theviewfinder and press the <FEL >button.The Speedlite will fire a preflash andthe required flash output for thesubject is retained in memory."FEL" will be displayed in theviewfinder for 0.5 sec.Each time you press the <FEL>button, a preflash will be fired and anew flash exposure setting will belocked.

o If the subject is too far away and underexposure will result, the < ~ > iconwill blink in the viewfinder. Move closer to the subject and try the FE lockagain.If <ETTL> is not displayed on the LCD panel, FE lock cannot be set.If the subject is too small, FE lock might not be very effective.

16

'I High-speed SyncWith high-speed sync (FP flash), the flash can synchronize with allshutter speeds. This is convenient when you want to use aperturepriority for fill-flash portraits.

ETT ~ Zoom SOmm Select <~>.Press the < ~H /~ > button so that<~> is displayed.In the viewfinder, check that the < ~H >icon is displayed.

[lJ If you set a shutter speed that is the same or slower than the camera'smaximum flash sync speed, < ~H > will not be displayed in the viewfinder.With high-speed sync, the faster the shutter speed, the shorter theeffective flash range will become. Check the LCD panel for the effectiveflash range.To return to normal flash, press the <~H/~> button again. The <eB>icon will disappear.Stroboscopic flash cannot be set.

17

Bounce Flash IIJI.llIlIIIlIll.1I111111111II11II11111111111111111••111111111111111_1.'

By pointing the flash head toward a wall or ceiling, the flash will bounceoff the surface before illuminating the subject. This can soften shadowsbehind the subject for a more natural-looking shot. This is called bounceflash.

Set the Bounce DirectionHold down the < PUSH> button and turn the flash head.If the flash coverage is set automatically, the flash coverage will be fixedto 50mm.The LCD panel will also display < - - > mm.., You can also set the flash coverage manually.

4) • If the wall or ceiling is too far away, the bounced flash might be too weakand result in underexposure.The wall or ceiling should be a plain, white color for high reflectance. Ifthe bounce surface is not white, a color cast may result in the picture.

• After you take the shot, if the flash exposure confirmation lamp does notlight, use a larger aperture opening and try again.

18

Creating a Catchlight

With the catchlight panel, you can create a catchlight in the subject'seyes to add life to the facial expression.

'1',: Point the flash head upward by90°.

Pull out the wide panel... The catch light panel will come out at

the same time.

Push the wide panel back in.Push in only the wide panel.Follow the same procedure as forbounce flash.

Point the flash head straight ahead and then upward by 900• The

catchlight will not work if you swing the flash head left or right.For maximum catchlight effect, stay within 1.5 m/4.9 ft of the subject.

Closeup Flash Shooting

When shooting a subject within about 0.5 - 2 m (1.6 - 6.6 ft) away, holddown the < PUSH> button and tilt the flash head downward by 7° toilluminate the lower part of the image.

ETTL Zoom 50mm... I ;' F- 5.6--.-

----=:-.::-.!:':.~:l-!.:?~ -0.5 0.7 1 1.5 2*""3/ l ' \i \\,.....13 18 m

19

ETTL mJZoom 2'-1mm

ZOOM:Setting the Flash Coverage and Using the Wide PanelThe flash coverage can be set to match the lens focal length from24mm to 105mm. The flash coverage can be set automatically ormanually. Also, with the built-in wide panel, the flash coverage can beexpanded for 14mm wide-angle lenses.

Press the <ZOOM/~> button.Turn the <@ > dial to change theflash coverage.If < 1m > is not displayed, the flashcoverage will be set automatically.

[l] If you set the flash coverage manually, make sure it covers the lens focallength so that the picture will not have a dark periphery.

l~ If you use a commercially-available sync cord to connect the camera tothe Speedlite's PC terminal, set the flash zoom manually.

Using the Wide Panel

Pull out the wide panel and place it overthe flash head as shown. The flashcoverage will then be extended for14mm.

The catchlight panel will come out atthe same time. Push the catchlightpanel back in.The <ZOOM/~> button will notwork.

[l] The flash coverage will not be compatible with the EF15mm f/2.8 Fisheyelens.

If you use bounce flash with the wide panel in place, the entire display onthe LCD panel will blink as a warning. Since the subject will beilluminated by both the bounce flash and direct flash, it will lookunnatural.Pull out the wide panel gently. Using excessive force may detach thewide panel.

20

Auto Zoom for Image Size

EOS DIGITAL cameras have one of three image sizes. The lens'effective focal length will differ depending on the camera's image size.The Speed lite automatically recognizes the EOS DIGITAL camera'simage size and automatically sets the flash coverage for lens focallengths from 24mm to 105mm.When the Speedlite is attached to a compatible camera, <§> willappear on the Speed lite's LCD panel.

ETTL Zoom Sam §

F- s.

-------0.50.7 1 1.5 2 3 4 6 9 13 18 m

Auto zoom can be disabled. (C.Fn-09 ----j- p.27)

21

M: ManuaI FIash 1\11111111111111111111IlI1III1IlI1IlI1III1IlI1I11I11IlI1I11I111111

You can set the flash output from 1/128 power to 1/1 full power in 1/3­stop increments.Use a hand-held flash meter to determine the required flash output toobtain a correct flash exposure.

M

til

II y

Zoom SDmm

Zoom SDmm

1 Press the <MODE> button so, that <M> is displayed.

Set the flash output.Press the < @ > button .

• ' The flash output blinks.Turn the <~ > dial to set the flashoutput, then press the < @ > button.

Press the shutter button halfway tosee the effective flash rangedisplayed.

Flash Output Display

When you change the flash output during shooting, the table belowmakes it easier to see how the stop changes such as 1/2 -0.3 ~ 1/2 ~1/2 +0.3. You can see how the stop changes when you increase ordecrease the flash output.For example, when you decrease the flash output to 1/2, 1/2 -0.3, or 1/2-0.7, and then increase the flash output to more than 1/2, 1/2 +0.3, 1/2+0.7, and 1/1 will be displayed.

<-- Figures for increased flash output

22

Metered Manual Flash Exposures

When the Speedlite is attached to an EOS-1 0 series camera, you canset the flash level manually for closeup subjects.

Set the camera and Speedlite.

• Set the camera's shooting mode to < M> or < Av >.

• ' Set the Speed lite to manual flash.

Focus the subject.

• Focus manually.

Set up an 18% gray card.Place the gray card at the subject's position.

• In the viewfinder, the entire spot metering circle at the centershould cover the gray card.

Press the <FEL> button. (816)

~, The Speed lite will fire a preflash and the required flash output forthe subject is retained in memory.On the right side of the viewfinder, the exposure level indicatorwill show the flash exposure level for the correct flash exposure.

Set the flash exposure level.Adjust the Speedlite's manual flash level and thecamera aperture so that the flash exposure levelaligns with the standard exposure index.

6 Take the picture.• Remove the gray card and take the picture.

[.lJ This feature works only with EX-series Speedlites with manual flash coupledwith an EOS-1D series camera.

23

MULTI: Stroboscopic FIash i~l.'l"'.lI'••l\II'.\••'lliIIIl

With stroboscopic flash, a rapid series of flashes is fired. It can be usedto capture multiple images of a moving subject in a single photograph.You can set the firing frequency (number of flashes per sec. expressedas Hz), the number of flashes, and the flash output.

MULTI

Zoom 3Smm

1/128 - -- 1HzPress the <MODE> button sothat <MULTI> is displayed.

Select the item to be set.Press the < @ > button to select theitem (blinks).

Set the desired number.Turn the < @ > dial to set the number,then press the <~> button.The next item to be set will blink.After you set the flash output andpress the <@ > button, all thesettings will be displayed.

Calculating the Shutter Speed

During stroboscopic flash, the shutter remains open until the firingstops. Use the formula below to calculate the shutter speed and set itwith the camera.

Number of flashes -7 Firing frequency =Shutter speedFor example, if the number of flashes is 10 and the firing frequency is5 Hz, the shutter speed should be at least 2 sec.

24

-- To avoid overheating and deteriorating the flash head, do not use stroboscopicflash more than 10 times in succession. After 10 times, allow the Speedlite torest for at least 15 min. If you try to use the stroboscopic flash more than 10times in succession, the firing might stop automatically to protect the flashhead. If this happens, allow the Speedlite to rest for at least 15 min.

[i] Stroboscopic flash is most effective with a highly reflective subjectagainst a dark background.Using a tripod, a remote switch, and external power source is recommended.A flash output of 1/1 or 1/2 cannot be set for stroboscopic flash.Stroboscopic flash can be used with "bulb."If the number of flashes is displayed as - ., the firing will continue until the shutter closes orthe battery is exhausted. The number of flashes will be limited as shown by the table below.

Maximum Stroboscopic Flashes

~•fllash OutplJ .•1 2 4 5 6-7 8-9

1/4 7 6 5 4 4 3 3

1/8 14 14 12 10 8 6 5

1/16 30 30 30 20 20 20 10

1/32 60 60 60 50 50 40 30

1/64 90 90 90 80 80 70 60

1/128 100 100 100 100 100 90 80

~flashOlltPlI.10 11 20-50 60 -199

1/4 2 2 2 2 2 2

1/8 4 4 4 4 4 4

1/16 8 8 8 8 8 8

1/32 20 20 20 18 16 121/64 50 40 40 35 30 20

1/128 70 70 60 50 40 40

If the number of flashes is displayed as - -, the maximum number of flashes willbe as shown by the table below regardless of the firing frequency.

Flash OutputFlash Count

25

~ Second-Curtain Sync ,11111111 11111111 II I III II

With a slow shutter speed, you can create a light trail following thesubject. The flash fires right before the shutter closes.

ETTL Zoom SOmm Press the <~H /~ > button so that<~> is displayed.

[]] Second-curtain sync works well in the camera's "bulb" mode.• To return to normal flash, press the <~H/~> button again. The <~>

icon will disappear.With E-TTL II/E-TTL, two flashes will be fired even at slow shutterspeeds. The first flash is only the preflash, and not a malfunction.

• Stroboscopic flash cannot be set.• Wireless flash cannot be set.

26

C.Fn: Setting Custom Functions 1"'\\'1.\'\\.'\\~\".'1\.'

You can customize Speed lite features to suit your shooting preferences.You do this with Custom Functions.

CustomFunction

No.Function Settings & Description

Referencepage

C.Fn-OO Distance indicator display

C.Fn-01 Auto power off

C. Fn-02 Modeling flash

C.Fn-03 FEB auto cancel

C.Fn-04 FEB sequence

C.Fn-05 Flash metering mode

C.Fn-06Quickflash with continuousshot

C.Fn-07 Test firing with autoflash

C.Fn-08 AF-assist beam firing

C.Fn-09 Auto zoom for sensor size

C.Fn-10 Slave auto power off timer

C.Fn-11 Slave auto power off cancel

C.Fn-12Flash recycle with externalpower source

C.Fn-13Flash exposure meteringsetting

o

o

Meters (m)

Feet (ft)

Enabled

Disabled

Enabled (Depth-of-field previewbutton)

Enabled (Test firing button)

Enabled (with both buttons)

Disabled

Enabled

Disabled

E-TTL II/E-TTL

TTL

External metering: Auto

External metering: Manual

Disabled

Enabled

1/32

Full output

Enabled

Disabled

Enabled

Disabled

60 minutes

10 minutes

Within 8 hours

Within 1 hour

Flash and external power

External power source

Speedlite button and dial

Speedlite dial only

p.10

p.44

p.15

p.12

p.55

p.30

p.30

p.10

p.49

p.21

p.39

p.48

p.14

27

Fn []: []

28

Hold down the <:,C?:-JC.Fn> buttonuntil <CIiD> is displayed.

Select the Custom Function No.Turn the < @ > dial to set the CustomFunction No.

Change the setting.Press the < €J > button.The Custom Function No. blinks.Turn the < @ > dial to set the desirednumber, then press the < €J > button.After you set the Custom Functionand press the <MODE> button, thecamera will be ready to shoot.

C.Fn-02-3: Convenient when you want to check the depth of field. (p.44)C.Fn-12: If an external power source is used, the flash recycling is

powered concurrently by the internal batteries and externalpower source. In this case, when the internal batteriesbecome exhausted first, shooting might not be possible. If 1is set, the flash recycling will be powered only by theexternal power source. The internal batteries will therebylast longer. Note that even if you set it to 1, the Speed lite willstill require internal batteries for flash control.

C.Fn-05-1 is geared for EOS-series film cameras.Do not set it if you have a, EOS DIGITAL camera or the EOS REBEL T2/300X. If C.Fn-05-1 is set for such cameras, the flash control will not workproperly. The flash might not fire or it might fire only at full output.With Type-A cameras, if C.fn-05-1 is set, wireless autoflash shooting willnot be possible.If "AF-assist beam OFF" is set with the Speedlite or camera, the AF­assist beam will not be emitted.

[l] With Type-B cameras, even if C.Fn-05-0 is set, E-TTL IliE-TTL autoflash willnot work.

29

Mem

External Flash Metering '"IRlln II ! I

The flash reflected off the subject is metered by an external meteringsensor in real time. When the standard flash exposure is attained, theflash output is cutoff automatically. Auto external metering compatiblewith the EOS-1 0 Mark III and manual external metering compatible withall EOS cameras are provided.

E: Auto External Metering

E Zoom 35mm Set auto external metering.F- 5.6 Set the Speedlite Custom Function to

em C.Fn-05-2. (p.27)

[lJ With auto external metering, the camera's ISO speed and aperture willbe set automatically in real-time by the Speedlite.Auto external metering will also work with flash exposure compensation(p.14) and FEB (p.15).

EM: Manual External Metering

E ISO Zoom 35mm '\~~1 Set manual external metering.:00 F- 5.6 l" Set the Speedlite Custom Function to

C. Fn-05-3. (p.27)

Set the Speedlite to the camera'sISO speed.

Press the < @ > button so the ISOspeed blinks.Turn the <@> dial to set the ISOspeed, then press the < @ > button.

30

Set the Speedlite to the camera'saperture setting.

Press the < @ > button so theaperture setting blinks.Turn the <@> dial to set theaperture, then press the <@> button.

After completing the settings, press theshutter button halfway. The effective flashrange will be displayed on the Speedlite'sLCD panel.

• With manual external metering, you can connect the camera to theSpeedlite's PC terminal with a sync cord and place the Speedlite at adifferent position from the camera.

e You cannot connect a Speedlite to another Speedlite's PC terminal witha sync cord. The second Speedlite will not fire.

31

Speedlite Control with the Camera's Menu ScreenIf the Speedlite is attached to an EOS camera which has a Speedlitecontrol function, it can control the Speedlite as shown below. For themenu operation procedure, refer to your camera's instruction manual.

• Setting Speedlite functionsThe settable functions will vary depending on the flash mode.· Flash mode· Shutter sync (1 st/2nd curtain)·FEB· Flash exposure compensation· Flash metering mode· Flash firing· Clear Speedlite settings

• Speedlite Custom Functions· C.Fn-OO - 13, Total 14

• Clear All Speedlite Custom FunctionsOnly C.Fn-OO will not be cleared.

Flash function settings screen*

* Screens from the EOS-1D Mark III.

Flash C. Fn settings screen*

U If flash exposure compensation has already been set with the Speedlite,flash exposure compensation cannot be set with the camera. To set it withthe camera, first set the Speedlite's flash exposure compensation to zero.

III If any Speedlite Custom Functions and flash function settings other thanflash exposure compensation have been set by both the camera andSpeedlite, the latest setting will take effect.

32

Wireless Flash

About Wireless Flash 34Wireless Settings.................................................. 36Fully Automatic Wireless Flash............................ 37Flash Ratio with E-TTL II 41Setting the Flash Output for Each Slave.............. 45Setting Manual Flash and Stroboscopic Flashwith the Slave 46

About Wireless Flash .IIIIIIIIIIIIIIIIIU.IIIIIIUIIII_I........_.

With multiple Canon Speedlites having the wireless flash feature, youcan create various lighting effects with the same ease as using normalE-TTL II autoflash.The settings you input with the 580EX II (master unit) attached to thecamera are also automatically transmitted to the slave units which arecontrolled by the master unit via wireless. Therefore, you need notoperate the slave unit(s) at all during the shoot.The basic wireless set-up is illustrated below. All you need to do is setthe master unit to <ETTL > enable wireless E-TTL II autoflash (p.37).Note that with Type-A cameras prior to the EOS-1 0 Mark II and EOSELAN 7NE/ELAN 7N/30V/33V, E-TTL autoflash will be used instead.

Positioning and Operation Range

8m (26.2ft.) 12m (39.4ft.)

III • Any flash exposure compensation, high-speed sync (FP flash), FE lock,FEB, manual flash, and stroboscopic flash settings set with the masterunit will all be automatically transmitted to the slave units.

• Even with multiple slave units, all of them will be controlled in the sameway via wireless.

• A 580EX II set as a slave unit can also be controlled by wireless bySpeedlite Transmitter ST-E2 (optional).

• Hereinafter, the "master unit" will refer to a 580EX 1\ attached to thecamera, and a "slave unit" will be a wireless 580EX II.

34

Multi-Speedlite, Wireless Lighting Configurations

You can create two or three slave groups and set the flash ratio for E­TTL II autoflash shooting (p.41 - 45).

Wireless flash with two slave groups (p.41)

Indoors

~B

8m (26.2ft.) 12m (39.4ft.)

Wireless flash with three slave groups (p.43)

Indoors

~B

8m (26.2ft.) 12m (39.4ft.)

35

Wireless 5ettin9s 1.\\\'\'\"""'11'.'\"""\I\\\II\1\\I\""\ll1\"\""'\""IlIill1l

You can switch between normal flash and wireless flash. For normalshooting, be sure to set the wireless setting to OFF.

Master Unit Setting

ETTL

-~--'-1-"------

Press the <ZOOM> button for 2sec. or longer until the displayblinks as shown on the left.

Set it as the master unit.Turn the < @ > dial until < '~jt''''I*' >blinks, then press the <@ > button.

< '~it''''I*' > and <I&:.> will bedisplayed, and the Speedlite is set asthe master unit.

mlZoom 2Ymm,I,... '\ I 1'-0 n­-emmI£.I'",. ; I ,\'

ETTL

_":.~--...-1-'------

ETTL mlZoom 2Ymm

Slave Unit Setting

Set it as a slave unit.Do the "Master Unit Setting"procedure above. For step 2, turn the<@> dial until <a"·"4_> blinks,then press the < @ > button.<a"·'9-> and <I&:.> will bedisplayed, and the Speedlite is set asa slave unit.

ETTL mlZoom 2Ymm

36

Fully Automatic Wireless FlashThis method has all the Speedlites fire at the same flash output with E­TTL II autoflash controlling the total flash output.

ETTL mJZoom 2'-1mm Set the camera-attached 580EX IIas the master unit.

ETTL mJZoom 2'-1mm Set the other 580EX IISpeedlites(s) as the wirelessslave unit(s).

ETTL mJZoom 2'-1mm

~~~~A

Check the communicationchannel.

If the master unit and slave unit(s) areset to a different channel, set them allto the same channel (p.40).

Position the camera andSpeedlites.

Position the Speed lites within therange shown on the next page.

Set the master unit's flash modeto <ETTL>.

For shooting, <ETTl> will also beset automatically for the slave unit(s).

Check that the flash is ready.When the slave unit(s) is ready to fire,the AF-assist beam will blink at 1-sec.intervals.

37

Check the flash operation.• Press the master unit's test firing

button.tl ' The slave unit will fire. If the flash

does not fire, adjust the slave unit'sangle toward the master unit anddistance from the master unit.

Set the camera and shoot..' Set the camera in the same way as

with normal flash shooting.

15m (49.2ft.)

8m (26.2ft.) 12m (39.4ft.)

• Use the mini stand (tripod socket provided) to prop up the slave unit.\1\ Use the bounce feature to swing the slave unit so that its wireless

sensor faces the master unit.,tt Indoors, the wireless signal can also bounce off the wall so there is

more leeway in positioning the slave unit(s).• After positioning the slave unit(s), be sure to test the wireless flash

operation before shooting.• Do not place any obstacles between the master unit and slave

unit(s). Obstacles can block the transmission of wireless signals.

38

[]] • The Speedlite's zoom setting will be set automatically to 24mm. It is possible tochange the master unit's zoom setting. However, note that the master unittransmits wireless signals to the slave unit(s} with the preflash. Therefore, theflash coverage must cover the slave unit's position. If you change the masterunit's zoom setting, be sure to test the wireless flash operation before shooting.

• If the slave unit's auto power off takes effect, press the master unit's testfiring button to turn on the slave unit.A test flash cannot be fired while the camera's operation timer 04 or 06 is active.

[lID The slave unit's auto power off time can be changed. (C.Fn-10 --+ p.27)

[lID The time during which the slave unit's auto power off can be canceled bythe master unit can be changed. (C.Fn-11 --+ p.27)

Master Unit's Flash ON/OFF

You can disable the master unit from firing so that only the slave unit(s)will fire a flash.

ETTL m»Zoom 2lJ..mln,.,I, -0 n--,.,?~~ermD" I "

'1 Press the <ZOOM/~> buttonso that the display blinks asshown on the left.

Disable the master unit's flashfiring.'. Turn the <@> dial to select <[I FF>,

then press the < @ > button.~" The icon will change to < "z.-' >.

ETTl mJZoom 2Ymm

[lJ Even if you disable the master unit's flash firing, it will still fire a preflash totransmit wireless signals.

39

Using Fully Automatic Wireless Flash

Flash exposure compensation and other settings set with the masterunit will also be automatically set in the slave units. Thus, you need notoperate the slave unit(s). Wireless flash with the following settings canbe done in the same way as with normal flash shooting.

· Flash exposure compensation· High-speed sync (FP flash)· FE lock

·FEB. Manual flash. Stroboscopic flash

[i] With FE lock, if even one Speedlite will result in underexposure, the < ~ >

icon will blink in the viewfinder. Open the aperture more or move the slaveunit closer to the subject.

Setting the Communication Channel

If there is another Canon wireless flash system nearby, you can changethe channel No. to prevent signal confusion. Both the master and slaveunits must be set to the same channel No.

ETTL ImZoom 2Ymm

:='!!3'~{~__..z.._~}_I_\"---

Press the <ZOOM/~> buttonso that <-.> blinks.

40

Set the channel No.Turn the <@ > dial to select thechannel number, then press the<@> button.

Flash Ratio with E-TTL IIWith one master unit and one slave unit or two slave groups, you canset the flash ratio for E-TTL II autoflash shooting.The example below has two slave units and the master unit disabledfrom firing.

Indoors12m (39.4ft.)

Setting the Slave UnitsTwo slave units can be assigned to different slave groups by setting theslave 10.

ETTL ailZoom 2Ymm

Set the wireless mode to<a,'·S!4_>. (p.36)

Press the <ZOOM/~> buttonso that <A> blinks.

41

Set the slave 10.• Press the <@ > button.~, Slave 10 <A> will be set.• For the other slave unit, do steps 1

and 2, turn the <@> dial to select< B>, then press the < @ > button.

• Slave 10 <B> will be set.

Setting the Master Unit and Shooting

1 Set the wireless mode to<'''Jt'S,i4:W>. (p.36)

ETTL (i!i)Zoom 2Ymm

ETTL (i!i)Zoom 2 ~lT'i'T1,.

,0 n/"IIICBII~~-

"z.I, ~~I

ETTL

Disable the master unit's flashfiring. (p.39)

Press the <ZOOM/~> buttonso that <-il'SIC.M> blinks.

Select the flash ratio.• Turn the <@> dial to select <A: B>,

then press the < @ > button.

Set the flash ratio.• Turn the < @ > dial to set the flash

ratio.

Set the camera and shoot.• Set the camera in the same way as

with normal flash shooting.

[lJ With the EOS ELAN II/ELAN II E/SO/SOE, EOS REBEL G/SOON, EOS IX,EOS IX Lite/IX?, EOS REBEL 2000/300, and REBEL XS N/ REBEL G 11/EOS 3000N/66, the flash ratio cannot be set with multiple Speedlites.

42

[l] • The flash ratio range of 8: 1 - 1:1 - 1:8 is equivalent to 3: 1 - 1:1 - 1:3 instops (1/2-stop increments).

• The flash ratio under the • mark is shown in parentheses below the scale.

8:1 • 4:1 • 2:1 • 1:1 • 1:2 • 1:4 • 1:8-------------_......(5.6:1) (2.8:1) (1.4:1) (1:1.4) (1:2.8) (1:5.6)

Wireless Flash with Three Slave Groups

Indoors12m (39.4ft.)

You can have slave groups A and B and also add slave group C. You can useslave groups A and B to obtain the standard flash exposure of the subject,and slave group C to illuminate the background to eliminate shadows.

'1 Set the slave units.• See "Setting the Slave Units" on page

41 to set the slave unit's 10 to < A >,<8>, or <C>.

• For slave < C>, also set the flashexposure compensation as necessary.

43

Set the master unit and shoot.Follow "Setting the Master Unit andShooting" on page 42. In step 4,select <A: B C>.

o If < IIlmmJI A: B> is set, the slave unit in slave group <C> will not fire.If you point the slave unit in slave group < C> toward the subject, thesubject will be overexposed.

Modeling Flash

If the camera has a depth-of-field preview button, pressing it will fire theflash continuously for 1 sec. This is called the modeling flash.It enables you to see the shadow effects on the subject and the lightingbalance. You can fire the modeling flash for both wireless and normalflash shooting.

o Do not fire the modeling flash more than 10 consecutive times. If youfire the modeling flash 10 consecutive times, allow the Speedlite torest for at least 10 min. to avoid overheating and deteriorating the flashhead.

~ The modeling flash cannot be fired with the EOS REBEL 2000/300 andType-B cameras (p.2).

About Slave Group Control

44

Slave group A

iii10 =A 10 =A 10 =A

For example, if you have the slave 10 setto < A > for three slave units, all threeslave units will be controlled as if theywere one Speed lite in slave group A.

Setting the Flash Output for Each SlaveWith manual flash and multiple Speed lites, you can set a different flashoutput for each slave unit.All settings are done with the master unit.

(l!i)Zoom 2Ymm

1/:K) IBIII EmmI

"Z.11

Press the <MODE> button sothat <M> is displayed.

M

Press the <ZOOM/~> buttonso that <-;1·'1(.-> blinks.

Select the flash ratio.Turn the <@ > dial to select <A: B>or <A: B: C>, then press the <@>button.

Set the flash output.Press the <@> button.The slave 10 <8> will blink.Turn the < @ > dial to set the flashoutput for < 8 >, then press the < @ >button.The slave 10 <~> will blink. Turn the< @ > dial to set the flash output for< ~ >, then press the < @ > button.The slave 10 <~> will blink. Turn the< @ > dial to set the flash output for<~>, then press the <@> button.All the slave IDs will light.

45

Setting Manual Flash and Stroboscopic Flash with the Slave 11

Manual flash or stroboscopic flash can be set manually with the slaveunit. As with studio flash units, you can set the flash output individuallywith the slave units for wireless or manual flash.

Manual Flash

IlaZoom 2Ymm,I;, 1/ 16-,~,- Z~~1EmII

Stroboscopic Flash

IlaZoom 2Ymm.... I '" 1/128 15- 'lOHz

-MUlTI- 11:>."'" I .... z~I, IEmII

46

• Hold down the <MODE> button for 2sec. or more.

~ <M> will blink.• Set the manual flash output (p.22).

• Hold down the <MODE> button for2 sec. or more.

.. <M> will blink.• Press the <MODE> button again

and <MULTI> will blink.• Set the stroboscopic flash (p.24).

Reference

580EX II System 48Troubleshooting Guide......................................... 50Specifications....................................................... 52Using a Type-B Camera....................................... 55

O)D® .....-----------1 "' .. -~--- .. ---'---:---'----1o8J1I1I/~1I/~ 8 I

CD Speedlite 580EX II (On-camera/Master unit)

(l) Speedlite Transmitter ST-E2

Dedicated transmitter for wireless control of 580EX 11/430EX set asslave units.

Q) Compact Battery Pack CP-E4Compact, lightweight, and portable external power pack. Providesthe same level of dust- and water-resistance as the 580EX II. It useseight size-AA alkaline or Ni-MH batteries. It can also use size-AAlithium batteries.

® EX-series Speedlite with slave function

~ Off-Camera Shoe Cord OC-E3

Enables the 580EX II to be connected to the camera up to 60 cm/2 ftaway. Provides the same level of dust- and water-resistance as the580EX II. All of the EOS camera's automatic functions can be used.

® Speedlite Bracket SB-E2

-- For the external power pack, use @ above. If a non-Canon, externalpower pack is used, it may cause malfunction.

48

About Color Temperature Information Transmission

When the flash fires, the color temperature information is transmitted tothe EOS DIGITAL camera. This feature optimizes the flash picture'swhite balance. When the camera's white balance is set to < m!i!l3 > or< ~ >, it will work automatically.To see if this feature works with your camera, see "White Balance"under "Specifications" in your camera's instruction manual.

About the AF-Assist BeamUnder low-light or low-contrast conditions, the built-in AF-assist beamwill be emitted automatically to make it easier to autofocus. The AF­assist beam works with all EOS cameras. The AF-assist beam iscompatible with 28mm and longer lenses. The effective range is shownbelow.

Position

Center

Periphery

Effective Range

0.6 - 10m / 2.0 - 32.8 ft.

0.6 - 5 m / 2.0 - 16.4 ft.

49

Troubleshooting Guide II III I J

If there is a problem, refer to this Troubleshooting Guide.

The Speedlite does not fire.

• The batteries are installed in the wrong orientation... Install the batteries in the correct orientation. (p.8)

• The Speedlite's internal batteries are exhausted.~ If the flash recycling time takes 30 sec. or longer, replace the

batteries. (p.8)~ Install the Speedlite's internal batteries even when you use an

external power source. (p.8)

The Speedlite is not attached securely to the camera.• ' Attach the Speedlite's mounting foot securely to the camera. (p.9)

• The electrical contacts of the Speedlite and camera are dirty.• Clean the contacts. (p.9)

The slave unit does not fire.

• The slave's wireless mode is not set to <a,'·S9_>.~' Set it to <a,,·S!)_>. (p.36)

• The slave unit{s) is not positioned properly.~ Place the slave unit within the master unit's transmission range.

(p.38).' Point the slave unit(s)'s sensor toward the master unit. (p.38)

The power turns off by itself.

• After 90 sec. of idle operation, auto power off took effect.Press the shutter button halfway or press the test firing button.(p.10)

The entire LCD panel blinks.

• The wide panel has been pulled out for bounce flash.~' Retract the wide panel. (p.20)

50

Auto zoom does not work.

• The Speed lite is -not attached securely to the camera.• ' Attach the Speedlite's mounting foot securely to the camera. (p.9)

The flash range scale bars blink.

• The flash head has been tilted down by 7°.Change the bounce position. (p.19)

The periphery or bottom of the picture looks dark.

When you set the flash coverage manually, the setting was a highernumber than the lens focal length, resulting in a dark periphery.

• ', Set the flash coverage that is a lower number than the lens focallength or set it to auto zoom. (p.20)

• If only the bottom of the picture looks dark, you were tooclose to the subject.

• If the subject is closer than 2 m/6.6 ft, tilt the flash head downwardby 7° (bounce flash). (p.19)

The flash exposure is underexposed or overexposed.

• There was a highly reflective object (glass window, etc.) in the picture.• ' Use FE lock. (p.16)

• The subject looks very dark or very bright.Set flash exposure compensation. For a dark subject, set adecreased flash exposure. And for a bright subject, set anincreased flash exposure. (p.14)

You used high-speed sync.With high-speed sync, the effective flash range will be shorter. Makesure the subject is within the effective flash range displayed. (p.17)

The picture is really blurred.

• The shooting mode was set to <Av>, and the sc~ne was dark.Use a tripod or set the shooting mode to < P>. (p.12)

51

On-camera, E-TTL II/E-TTL/TTL autoflash Speedlite

Type-A EOS cameras (E-TTL II/E-TTL autoflash)

Type-B EOS cameras (TTL autoflash)

58/190 (at 105mm focal length, ISO 100 in meters/feet)

24 - 105mm (14mm with wide panel)

· Auto zoom (Flash coverage set automatically to match thelens focal length and image size)

· Manual zoom

· Swinging/tilting flash head (bounce flash)

Normal flash: 1.2 ms or shorter, Quick flash: 2.3 ms or shorterFlash duration:

Color temperature

information transmission: Flash color temperature information transmitted to camerawhen flash is fired

Guide No.:

Flash coverage:

Specifications-TypeType:

Compatible cameras:

- Exposure ControlExposure control system:

Effective flash range:

(With EF50mm f/1.4 lens

at ISO 100)

E-TTL II/E-TTL/TTL autoflash, auto/manual external

metering, manual flash

Normal flash: Approx. 0.5 - 30 m I 1.6 - 98.4 ft.

Quick flash: 0.5 - 7.5 m I 1.6 - 24.6 ft. (min), 0.5 - 21 m I 1.6 ­68.9 ft. (max)

High-speed sync: 0.5 - 15 m I 1.6 - 49.2 ft. (1/250 sec.)Flash exposure

compensation:

FE lock:High-speed sync:

Stroboscopic flash:Flash exposure

confirmation:

Manual, FEB: ±3 stops in 1/3-stop increments (Manual and

FEB can be combined)

With <FEL> button or <*> buttonProvidedProvided (1 - 199 Hz)

Pilot lamp lights

- Flash Recycling (with size-AA alkaline batteries)Recycling timelFlash-ready indicator: Normal flash: Approx. 0.1 - 5 sec. I Red pilot lamp lights

Quick flash: Approx. 0.1 - 2.5 sec. I Green pilot lamp lights

52

• Wireless FlashTransmission method: Optical pulse

Channels: 4

Wireless options: OFF, Master, and Slave

Transmission range (Approx.): Indoors: 12 - 15 m /39.4 - 49.2 ft.,

Outdoors: 8 - 10m /26.2 - 32.8 ft.Master unit reception angle: ±40° horizontal, ±30° vertical

Controllable slave groups: 3 (A, B, and C)Flash ratio control: 1:8 - 1:1 - 8:1 in 1/2-stop increments

Slave-ready indicator: AF-assist beam blinksModeling flash: Fired with camera's depth-of-field preview button

• Custom Functions: 14 (32 settings)

• AF-Assist BeamLinkable AF points: 1 - 45 AF points (28mm or longer focal length)

Effective range (Approx.): At center: 0.6 - 10m /2.0 - 32.8 ft.,

Periphery: 0.6 - 5 m /2.0 - 16.4 ft.

• Power SourceInternal power:

Battery life(Approx. flash count):Wireless transmissions:

Power saving:

External power:

• Dimensions(W x H x D):

• Weight (Approx.):

Four size-AA alkaline batteries* Size-AA Ni-MH and lithium batteries also usable

100 - 700 flashes (with size-AA alkaline batteries)Approx. 1500 transmissions (With master unit firing disabled

and size-AA alkaline batteries)Power off after certain period of idle operation (Approx. 1.5 min.to 15 min.) (60 min. if set as slave)

Compact Battery Pack CP-E4

76 x 137 x 117 mm / 3.0 x 5.4 x 4.6 in.(excluding dust- and water-resistant adapter)

405 g / 14.3 oz. (Speedlite only, excluding batteries)

All specifications above are based on Canon's testing standards.Product specifications and external appearance are subject to change withoutnotice.

53

Guide No. (at ISO 100, in meters/feet)

Normal Flash (Full Output) and Quick Flash

Flash Coverage(mm) 14 24 28 35 50 70 80 105

Normal Flash(Full output)

Quick Flash

Manual Flash

15/ 28/ 30/ 36/ 42/ 50/ 53/ 58/49.2 91.9 98.4 118.1 137.8 164 173.9 190.3

Same as 1/2 to 1/6 manual flash output

Flash OutputFlash Coverage (rnrn)

14 24 28 35 50 70 80 105

15/ 28/ 30/ 36/ 42/ 50/ 53/ 58/49.2 91.9 98.4 118.1 137.8 164 173.9 190.3

10.6/ 19.8/ 21.2/ 25.5/ 29.7/ 35.4/ 37.5/ 41/34.8 65 69.6 83.7 97.4 116.1 123 134.5

7.5/ 14/ 15/ 18/ 21/ 25/ 26.5/ 29/24.6 45.9 49.2 59.1 68.9 82 86.9 95.1

5.3/ 9.9/ 10.6/ 12.7/ 14.8/ 17.7/ 18.7/ 20.5/17.4 32.5 34.8 41.7 48.6 58.1 61.4 67.3

3.8/ 7/ 7.5/ 9/ 10.5/ 12.5/ 13.3/ 14.5/12.5 23 24.6 29.5 34.4 41 43.6 47.6

2.7/ 4.9/ 5.3/ 6.4/ 7.4/ 8.8/ 9.4/ 10.3/8.9 16.1 17.4 21 24.3 28.9 30.8 33.8

1.9/ 3.5/ 3.8/ 4.5/ 5.3/ 6.3/ 6.6/ 7.3/6.2 11.5 12.5 14.8 17.4 20.7 21.7 24

1.3/ 2.5/ 2.7/ 3.2/ 3.7/ 4.4/ 4.7/ 5.1/4.3 8.2 8.9 10.5 12.1 14.4 15.4 16.7

54

Using a Type-B Camera 110111.111.11•.•11.1111111......I.II.IIII.U.1.;

If you use the 580EX II with a Type-B camera (TTL autoflash camera),note the available features and restrictions below.When a Type-B camera is used with the 580EX II set to autoflash,<TTL> will be displayed on the Speedlite's LCD panel. (With a Type-Acamera, <ETTL> will be displayed.)

Features Available with Type-B Cameras· TTL autoflash

· Flash exposure compensation

· FEB

· Manual Flash

· Stroboscopic flash

· Second-curtain sync

· Manual external metering

· Wireless slave flash with manual flash

· Wireless slave flash with stroboscopic flash

Features not Available with Type-B Cameras· E-TTL II/E-TTL autoflash

· FE lock

· High-speed sync (FP flash)

· Autoflash with wireless flash

· Flash ratio set with wireless slave units

55

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

Do not make any changes or modifications to the equipment unless otherwisespecified in the instructions. If such changes or modifications should be made,you could be required to stop operation of the equipment.

This equipment has been tested and found to comply with the limits for a classB digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more ofthe following measures:

Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numerique de la c1asse Best conforme a la norme NMB-003 duCanada.

56

The apparatus shall not be exposed to dripping or splashing.Batteries shall not be exposed to excessive heat such as sunshine, fire or thelike.Dry batteries shall not be subjected to charging.

C This mark indicates that the product complies with Australia's EMCregulations.

-European Union (and EEA) only.

This symbol indicates that this product is not to be disposed of withyour household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over toa designated collection point, e.g., on an authorized one-for-onebasis when you buy a new similar product or to an authorizedcollection site for recycling waste electrical and electronicequipment (EEE). Improper handling of this type of waste couldhave a possible negative impact on the environment and humanhealth due to potentially hazardous substances that are generallyassociated with EEE. At the same time, your cooperation in thecorrect disposal of this product will contribute to the effective usageof natural resources. For more information about where you candrop off your waste equipment for recycling, please contact yourlocal city office, waste authority, approved WEEE scheme or yourhousehold waste disposal service. For more information regardingreturn and recycling of WEEE products, please visit www.canon­europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

57

Canon

This Instructions booklet is dated February 2007. For information on thecamera's compatibility with system accessories marketed after this date, contactyour nearest Canon Service Center.

CanonCANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

U.S.A. ---- CANON U.S.A. INC.One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.For all inquires concerning this product, call toll free in the U.S.1-800-0K-CANON

CANADA --- CANON CANADA INC. HEADQUARTERS6390 Dixie Road, Mississauga, Ontario L5T 1P7, CanadaCANON CANADA INC. MONTREAL BRANCH5990, C6te-de-Liesse, Montreal Quebec H4T 1V7, CanadaCANON CANADA INC. CALGARY OFFICE2828, 16th Street, N.E. Calgary, Alberta T2E 7K7, CanadaFor all inquiries concerning this product, call toll free in Canada1-800-0K-CANON

EUROPE, --- CANON EUROPA N.V.AFRICA & Bovenkerkerweg 59-61, P.O. Box 2262, 1180 EG Amstelveen, The NetherlandsMIDDLE EAST CANON COMMUNICATION & IMAGE FRANCE S.A.S.

12 Rue de l'lndustrie 92414 Courbevoie Cedex, FranceCANON UK LTD.Woodhatch Reigate Surrey RH2 8BF, United KingdomCANON DEUTSCHLAND GmbHEuropark Fichtenhain A10, 47807 Krefeld, GermanyCANON ITALIA S.p.A.Via Milano 8 1-20097 San Donato Milanese, Milano, ItalyCANON Schweiz AGGeschaftsbereich Wiederverkauf, Industriestrasse 12, CH-8305 Dietlikon, SwitzerlandCANON GMBHZetschegasse 11, A-1230 Wien, AustriaCANON Espana, S. A.C/Joaqufn Costa, 41, 28002 Madrid, SpainSEQUE Soc. Nac. de Equip., Lda.,Praya da Alegria, 58, 2°, 1269-149 Lisboa, Portugal

CENTRAL & -- CANON LATIN AMERICA, INC.SOUTH AMERICA 703 Waterford Way, Ste. 400 Miami, FL 33126, U.S.A.

ASIA CANON (China) Co., Ltd.15F Jinbao Building NO.89 Jinbao Street, Dongcheng District, Beijing 100005, ChinaCANON HONGKONG CO., LTD.19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong KongCANON SINGAPORE PTE. LTD.1 HarbourFront Avenue, #04-01 Keppel Bay Tower, Singapore 098632CANON KOREA CONSUMER IMAGING INC.Startower Bldg.17F,737,Yeoksam-Dong, Kangnam-Ku, Seoul, 135-984, Korea

OCEANIA --- CANON AUSTRALIA PTY. LTD.1 Thomas Holt Drive, North Ryde, N.S.W. 2113, AustraliaCANON NEW ZEALAND LTD.Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand

JAPAN ---- CANON MARKETING JAPAN INC.16-6, Kohnan 2-chome, Minato-ku, Tokyo 108-8011, Japan

CT1-7768-000 © CANON INC. 2007

PRINTED IN JAPANIMPRIME AU JAPON

IMPRESO EN JAPON

Ca......ol8tl CANON PHOTOGRAPHIC PRODUCTS~.. '.. INTERNATIONAL SERVICE NETWORK

~1'.I/1J)<51E~if-t::::·A.

2ftMAl-';C;cl-';c~l'.1 /~~o)~~ld:, "'Hc~l'.1 /i~~ffi~~DILLiD~11 L. LiDt) *90 IElltRi*~iI~ Ct~cCanon International WarrantySystemO):;/itt')I/~-:7) i10)~~Id:, ftMAcn;clEt->~fij$'i-ct>, Ef)x-:7o)i1l-';d~~~DILLi*~~i~~~iD~11L. LiDt) *90 i*~~i~~~S~11IL~:Q~tild:, tt:'\g:.i*~iI~~~L.Ll'Cl-'o i*~~o)~~1J'i~l-'~tit->i*~iI~ILft&7'CJ6~, ftMAB1J'i~l-'~tild:~*~c:~t)*9o· i~~~gILJ:-:JLId:, $~~~81JIL~1:>ZL.~11nlcJ:·~5g:., immJ:t)t>B~1J'i1J\1J\:Q~tit>®t)*9o

· ~tilL J: t)~cl£~g~~~9 :Q~ti1J'i® t) *90· 31):;Z HLfml- 'if-t::::':;ZW1BO)rD~l- 'tibttld:i§-@~O)i~~~DA"iDrD~l- 'tibttJ.jjl-'*90

Canon Photographic Product International Service NetworkService of your Canon product will be provided at any of the listed authorized service facilities. Warranty service of products with international Warranty certificate (with thesymbol ffi for Canon International Warranty System indicated above) will be provided at the listed service facilities marked ffi in areas other than the country or regionwhere the product was purchased. You must present your warranty certificate when requesting repairs during the warranty period. If no certificate is presented, or if thewarranty does not bear the place and date of purchase, you will be charged the cost of the repairs.eSome types of repair may require that parts be ordered specially. In this event, the repairs may take longer than usual.eThe contents of this document are subject to change without notice.

CANON mUfHJ1.lE~~&~~J'L 91J~ ~1{1'f.J fIM ij~*J¥! {¢j 1fI\fm)~ f~ft~ Calloll fin~F J~ tJtiJtnfJi *ft~ ... .(E ft.] ~;/~: J~ ft~ [f~ '~EX.f1i1. rx k:J. 9rft~ .f1i1.lt. mJf,l; i;~ 14' Ef) fJFi.Cft~ 91J;g ijlJi*!'(!{V: t!p n~tJld~~-t*:fftJilWf-1*iJE11

; (1W:ff J:[fij)iJTt~ Calloll f1fj~tJi.jWd:~H·jE#dft m!¥Jf,);i.C Ef») A~ Calloll f£fj~FJt!¥J{~liEij~* '(H~j..I1Jt'HrJ)rJ-J. '~f~~:i!{~Flltl1't, 'f:E~ili/J~f~!¥J1*

iJE f; ~n"FH1/J~{¥iJF.1S. Exf¥Hlf;~dc~ft.]4~r"':8~A~ifflJ~if!lHWHH. {l!3iJif,t ·tJH~Jlft~Jtj

• rttj/-~ JfJ ;rtf' lIt A~ {~JItI liJ ~'J6' 3w tit hi! if~ 4'={4' [*J ltt. .IlJfj~ffif ~!f5<' Kft~ {~JIIfMill)• ~j:,{trf,J~HJifr'~!£H,t. ~J.~/F~1T$%

CANON WH(~HI~~~IH~~

R 91J 7, ~tf:B'~ H{oJijlltffi \'fl. {II. $fj~ t~ fe.~!¥J Calloll ftfj~@ J11 tJtf~nfHMt'~ .. 11: 1I1nV¥ ~h ft~ ~~ *£&.f1i1. [.Po: ~~ frAS .f1i1.lMrfti t\HliHl' EB m~cA~ 71J~ ijlJim~11Lt!P ~tJt{~Im~:ff[ifJ~f¥,wff(~1f LiIDJiJTtI'r CanoIl1tfj~~~{¥,m~U1Emft~m~c EB) ft~ Canoll fUj~J¥JtB'~f¥.mijlJim {H*.m<Mrrt1r*J, 'gjf~~~{~@J111if, --5E~t±H~fe.~B''1f¥~

• f{rl,Ftf:j}J~i~~~. 9X:f~~.~~l:illtll1i~rfMl!¥JIYj)hf1l HMlIiJ, f~3~H ·tJH~J1B'VH• ~j/-t;JtUtlf~~!¥Jf~JIf\11Jfj~iJ6·3fitf~JIJ;fJ1I1f~1t- [);Iltt., IlJfm'r¥if~~Rft~{~J!j!M"~

·1>:k1t-r*JWfOifr.~rE:IF.J, ~g+7Hj~1ii

Weltweites Kundendienstnetz fUr Canon KamerasIhr Canon Produkt wird bei jeder der aufgelisteten autorisierten Kundendienststellen gewartet und repariert. Garantieleistungen fOr Produkte mil der Internationalen Garanliekarte(gekennzeichnet mit dem Symbol (f) fOr das Internationale Canon Garantiesyslem) erhalten Sie in anderen Gebieten als dem Land oder der Region, wo das Produkt gekauft wurde,bei den in der Liste mit (f) gekennzeichneten Kundendienststellen. Wenn Sie das Produkt wahrend der Garantiezeit zur Reparatur geben, mOssen Sie Ihre Garantiekarte vorlegen.Wenn Sie keine Garantiekarte vorlegen oder wenn die Garantiekarte nicht den Ort und das Datum des Kaufs tragt, werden Ihnen die Kosten der Reparatur in Rechnung gestellt.e E.inige Arten von Reparaturen k6nnen die Bestellung spezieller Teile erfordern. In diesem Fall kann die Reparatur langer als normal dauern.eAnderungen des Inhalts dieses Dokuments sind ohne VorankOndigung vorbehalten.

Reseau International des Services Canon Appareil-PhotoVotre appareil Canon pourra etre repare dans un des centres de service apres-vente agrees indiques dans la liste ci-dessous. II sera repare sous garantie contre presentationdu Certificat de Garantie (avec la marque ffi du Systeme de Garantie Internationale Canon) dans les centres de service apres-vente indiques par la marque ffi dans les paysou regions autres que celui ou Ie produil a ete achete. Vous devrez presenter votre certificat de garantie pour toute demande de reparation pendantla periode de validite dela garantie. Toutefois, les reparations seront avos frais si vous ne presentez pas volre garantie ou si elle ne comporte ni I'adresse du revendeur ni la date d'achal du produit.eCertaines reparations peuvent necessiter des commandes de pieces speciales. Dans ce cas, elles peuvent durer plus longtemps que prevu.e Le contenu de ce document peut faire I'objet de modifications sans preavis.

Rete Di Assistenza Internazionale Per Fotocamere CanonL'Assistenza del prodotto Canon acquistato sara fornita presso uno qualsiasi dei centri di assistenza autorizzati riportati nella lista.L'assistenza in garanzia di prodotti con certificato di garanzia internazionale (con il simbolo ffi per il sistema di garanzia internazionale Canon sopra indicato) sara fornitapresso i centri di assistenza riportati nella lista contrassegnati da ffi in aree diverse dal paese 0 dalla regione in cui e state acquistato il prodotto. Enecessario presentare ilcertificato di garanzia di cui si e in possesso quando si rechiedono prestazioni di assistenza durante il periodo di validita della garanzia. Se non si presenta il certificato, 0se la garanzia non reca Ie indicazioni del luogo e della data di acquisto, la riparazione sara a pagamento.ePer alcuni tipi di riparazione pub essere necessario ordinare a parte i pezzi di ricambio. In questa caso, la riparazione richiedera piu tempo del normale.e II contenuto di questa documento e soggetto a modifiche senza preavviso.

Sistema Internacional de Servicio de Camaras Fotograficas CanonEI servicio de su producto Canon sera proporcionado por cualquiera de las instalaciones de servicio autorizadas mencionadas en la lista. EI servicio de garantfa de losproductos con certificado de Garantfa Internacional (con el simbolo ffi del Sistema de Garantfa Internacional de Canon indicado arriba) sera proporcionado por lasinstalaciones de servicio que figuran en la lista con la marca ffi, en otras areas distintas del pais 0 de la regi6n donde se adquiri6 el producto. Cualquier solicitud dereparaci6n durante el periodo de garantfa se realizara al presentar el certificado de garantfa debidamente lIenado incluyendo ellugar y la fecha de compra, en caso de noser as! la reparaci6n sera con cargo al cliente.eAlgunos tipos de reparaciones podrian requerir un pedido especial de repuestos. En tal caso, las reparaciones podrian demorar mas de 10 habitual.e Los contenidos de este documento se encuentran sujetos a cambios sin previa aviso.

lil~lii#l·"'i'ti.~".i:t·'~tl#l·jl",

Phone: (81) 03-3455-9353

nilill"·"'·"'·"it4%hffi·,i.i,';.i"i

jiilijtUi,Ji','i',J'ffi;,t.i,$t16·;·i"i

(64) 09-489-0470

(351) 021-3242830(386) 01-5461000(34) 091-5384500

08-74486200848-833-838

08-705-143723(420) 02-25280-111(420) 02-22721-525(48) 022-572-30-00(48) 022-862-41-38(421) 02-5441-4880

(357) 25-384306(357) 25-568274

(98) 021-8752442

(972) 03-6888525(966) 02-6970779/

6970652(27) 011-2667162

jiilillii.iii.'ii.iaffi;,i.i,hq.i"p:;"

Phone:

Phone:

Phone:Phone:Phone:Phone:Phone:Phone:Phone:Phone:Phone:Phone:Phone:Phone:

Phone:Phone:

Phone:

Phone: 13-13-83--Within Australia only

(61) 02-9805-2555Fax: (61) 02-9888-3314

Praca da Alegria. 58-2, 1269-149 Lisboahttp://www.3a-servis.siJoaquin Costa, 41 • 28002 Madridhttp://www.canon.sehttp://www.canon.chhttp://www.canon.co.uk160 00 Praha 6Milesovska 1, 130 00 Praha 3http://www.canon.plul. Zytnia 15, 01-014 WarszawaRadlinskeho 26, 811 07 Bratislava115 Omonias Avenue Paroutis Building.3045 Limassol127, South Sohrevardi AvenueP.O. Box 11365/1167, Tehran50 Anilevitch St, Tel Aviv 67060PO. Box 1796. Jeddah 21441

P.O. Box 1782 Halfway House 1685Johannesburg

*For service center location, please contact the phone number above.

Ef) Karat Israel Ltd.Ef) AIQuraishi Leisure Services

Ef) Aphomar Co. Ltd.

Ef) Canon South Africa.

Ef) Canon New Zealand Ltd.Akoranga Business Park, Akoranga Drive Northcote. Auckland. New Zealand

Ef) SEQUE S.A.Ef) 3A AUDIO VIDEO ServisEf) Canon Espana, S.A.Ef) Canon Nordic Regional Competence CenterEf) Canon Schweiz AGEf) Canon UK Regional Competence CenterEf) Canon CZ S.R.O.Ef) AWH serviceEf) Canon Polska SP.Z.O.O.Ef) CSI Foto VideoEf) Pro LaikaEf) NT. Kakoyiannis/Paroutis Electronics Ltd.

NEW ZEALAND

POLAND

SLOVAKIACYPRUS

PORTUGALSLOVENIASPAINSWEDENSWITZERLANDUNITED KINGDOMCZECH REP.

REGIONAL Ef) CANON AUSTRALIA PTY. LTD.HEADQUARTERS

IRAN

ISRAELSAUDI ARABIA

SOUTH AFRICA

(852) 2170-2888(852) 2428-3963(852) 2170-2888(852) 2428-3963

(62) 021-651-1533(62) 021-651-0472(82) 02-2017-8600(82) 02-2017-8796(60) 03-7845-0055(60) 03-7844-6044

(63) 02-812-6047(63) 02-812-0067

(65) 6799-8888(65) 6799-8882

(886) 02-2537-1172(886) 02-2571-7171

(66) 02-344-9999(66) 02-344-9910

Phone:Fax:Phone:Fax:Phone:Fax:Phone:Fax:

Phone:Fax:Phone:Fax:Phone:Fax:Phone:Fax:Phone:Fax:

(--- ) - Country & Area Code

iiiF:lf&ELill18i£ICANON MARKETING JAPAN INC.

Ef) Canon HongKong Co. Ltd. - Domestic Sales Officee Kowloon Depot:18/F The Metropolis Tower, 10 Metropolis Drive Hunghom, Kowloon Hong Konge HongKong Depot:10/F Beverly House, 93-107 Lockhart Rd, Wan Chai, Hong Kong

Ef) Pt. INTER-DELTA TbkJI. Gaya Motor Barat, Sunter II Jakarta 14330

Ef) Canon Korea Consumer Imaging Inc. Canon Support Center2F Samwhan Artnubeau III, 209 Nonhyun 2 Dong, Kangnam-gu, Seoul

Ef) Canon Marketing (Malaysia) Sdn. Bhd.Block D, Peremba Square, Saujana Resort, Section U2, 40150 Shah Alam,Selangor Darul Ehsan Malaysia

Ef) Canon Marketing (Philippines) Inc.Marvin Plaza Building. 2153 Don Chino Roces Ave. Makati City, Metro Manila

Ef) Canon Singapore Pte. Ltd.1 HarbourFront Avenue #04-01 Keppel Bay Tower Singapore 098632

Ef) Rainbow Photo & Image Equipment Co. Ltd.No. 20 Chiling Road, Taipei 10424. Taiwan

Ef) Canon Marketing (Thailand) Co.Ltd10th Floor, Bangkok City Tower, 179/34-45 South Sathorn Road. Bangkok 10120

THAILAND

KOREA

PHILIPPINES

MALAYSIA

TAIWAN

SINGAPORE

REGIONALHEADQUARTERS

INDONESIA

HONG KONG

lij#l~••·'tj.~"i.)I ••:',!&I#I-j(", n;liIJi','i:,'XJ,J,q:;,i.i"m;;'hi"iY;'ffii;.i"iREGIONAL CANON LATIN AMERICA, INC. Phone: 1-305-260-7400HEADQUARTERS (Except Mexico)

-For service center location, please visit our website or contact the phone number above.

REGIONAL CANON U.S.A., INC.HEADQUARTERS

Phone: (673) 02-653001

Phone: (855) 023-426414Fax: (855) 023-426014Phone: (86) 010-9517-7178

Phone: (91)-012-45160000Fax: (91 )-012-45160011Phone: (95) 01-202-092Fax: (95) 01-202-079Phone: (92) 021-438-9581Fax: (92) 021-438-9589Phone: (94) 01-12437797Fax: (94) 01-12448980Phone: (977) 01-422-4079Fax: (977) 01-422-9358Phone: (62) 021-424-4204Fax: (62) 021-424-7017

Phone: (7) 095-258600

Phone: (36) 01-2668085Phone: (356) 448466Phone: (965) 2-44810315Phone: (968) 706153Phone: (971) 04-3534168Phone: (961) 01-582-000Phone: (372) 630-0530Phone: (371) 720-4444Phone: (370) 8700-555-78

Kosmodamianskaya nab. 52. Building 3,5th Floor 113054 MoscowSomogy 1. Bela u. 10, 1085 Budapesthttp://www.pcutajar.com.mtPO. Box 974 Safat 13008PO. Box 3139. Ruwi 112PO.Box 284 Dubai460 Corniche AI-Nahr, Beiruthttp://www.canon.eehttp://www.canon.lvhttp://www.canon.lt

• Camera Kft• P. Cutajar• Naser Mohammed, AI Sayer Comm.Co.eGENETCO• Khoory Electronics• Image System sal• AS KTK Overall• Canon North-East Oy• Canon North-East Oy

-Service facilities listed below are not "International Warranty Members"They do not accept any warranty repair but may assist you when the repair charge is acceptable.

• Interhouse CompanyNO.5 & 6, Bunut Jaya Complex, Simpang 574,Krn 71/4, Jalan Tutong. Bandar Seri Begawan 2690, Brunei Darussalame Royal Cambodia Co., Ltd6th Floor, Royal Group Building, 246 Preah Monivong Boulevard. Phnom Penh• Canon(China)Co., Ltd.15F Jinbao Building No. 89 Jinbao Street, Dongcheng District, Beijing 100005. China• Canon India Pte. Ltd.2nd Floor, Tower A & B Cyber Greens, DLF Phase III Gurgaon-122 002. Haryana. India• Accel International Co., Ltd.Level 6. FJV Commercial Centre, 422-426 Strand Road, Botataung, Township, Yangon• Global Systems39-C/1, Block-6, P.E.C.H.S Off: Shahrah-e- Faisal, behind Jason Trade Centre, Karachi 75400e Homebase(Pvt.)LimitedNO.85 Braybrooke Place, Colombo 02, Sri Lankae Primax International Inc.3rd Floor, Maitry Bhavan. New Road, Kathmandu, Nepale PT DatascripJI. Angkasa no 18 BD,Jakarta, Indonesia

MYANMAR

NEPAL

ASIABRUNEI

EUROPE I MIDDLE EAST I AFRICA ----------------------------------CIS e Canon Representative Office

CHINA

SRI LANKA

PAKISTAN

CAMBODIA

INDONESIA

INDIA

HUNGARYMALTAKUWAITOMANUAELEBANONESTONIALATVIALITHUANIA

'~(·)~eMl~'~;::I~i;:j::l·b

Phone: 0810-081009Phone: 070-300-012Phone: (34) 28-470008Phone: (34) 28-470008Phone: 70-2055-15Phone: 020-366-466Phone: 0825-002-923Phone: 0180-500-6022Phone: (30) 0210-955-4000Phone: (354) 533-3411Phone: (353) 01890-200-563Phone: 848-800-519Phone: 27-302-054Phone: 0900-202-2915Phone: 226-29321

Phone: 1-800-828-4040-Within US only

fiilijtl",';',''',''ffi;,;··,·ffi;Phone: 1-800-828-4040

-Within Canada only

Phone: (31) 020-545-8545Fax: (31) 020-545-8211

Phone: 01-800-710-7168--Within Mexico only

(52) 052-494-905Fax: (52) 052-494-944

nililJii.i'i.i'paffi;';.;';A.",h"i i

jiili1thi.iXi.iXi.iaffi;,i.i,64';··illiii!1lUi

http://www.canon.athttp://www.canon.beIslands 57, La Naval-Las Palmas23, Irneldo Seris-Sta Cruz de Tenerifehttp://www.canon.dkhttp://www.canon.fihttp://www.canon.frhttp://www.canon.dehttp://www.intersys.grLangholtsvegur 84. 104 Reykjavikhttp://www.canon.iehttp://www.canon.ithttp://www.canon.luhttp://www.canon.nlhttp://www.canon.no

CANON MEXICANA, S.DE R.L. DE C.V.Manuel Avila Camacho No. 138, PB Ypisos 15,16 Y 17 Col. Lornas deChapultepec Delegacion Miguel Hidalgo, C.P 11000 Mexico, D.F.-For service center location, please contact the phone number above or send an e-mail to:canonmx_soporte@cusa. canon. com

-For service center location. please visit our website or contact the phone number above.

CANON CANADA INC.,

-For service center location, please visit our website or contact the phone number above.

REGIONALHEADQUARTERS

REGIONAL CANON EUROPA N.VHEADQUARTERS P.O. Box 2262, Bovenkerkerweg 59-61 1180 EG Amstelveen, The Netherlands

-For general Inquiry only. For repair, please contact one of service center listed below.-Within Local oniy for non-Country & Area Code No.

REGIONALHEADQUARTERS

AUSTRIA Ef) Canon Ges.m.b.HBELGIUM Ef) Canon Belgium N.V. / S.A.CANARY ISLANDS Ef) Chellsons S.A.

Ef) Chellsons S.A.DENMARK Ef) Canon DenmarkFINLAND Ef) Canon OyFRANCE Ef) Canon France Regional Competence CenterGERMANY Ef) Canon Germany Regional Competence CenterGREECE Ef) Intersys SAICELAND Ef) Beco ehfIRELAND Ef) Canon Ireland Ltd.ITALY Ef) Canon Italy Regional Competence CenterLUXEMBOURG Ef) Canon Luxembourg S.A.THE NETHERLANDS Ef) Canon Nederland N.VNORWAY Ef) Canon Norge A1S

PRESENT OWNERSHIP AND PRODUCTS INTERESTED INArticles dejA en possession au juges dignes d'interlltProduetos en posesi6n y que Ie interesan

CAMERASAppareils-photoCAMARAS

(Camera)(Appareil)(CAMARAS)

(Camera)(Appareil)(CAMARAS)

Complete this card at time of sale.

(Camera)(Appareil)(CAMARAS)

(Camera)(Appareil)(CAMARAS)

A remplir au moment de I'achat

OWN INTERESTED INEn possession Interesse parEN POSESI6N INTERESADO EN

D DD D

L1ene esta tarjeta en el momento de la venta.

CT5-7728-004

MODEL SERIAL NO.Modele No. de serle

MODELO SF'EEDLITE 58~3E:i~ II N' DE SERlE

PRINTED IN JAPAN

INTERCHANGEABLE LENS OWN INTERESTED IN OTHER ACCESSORIES OWN INTERESTED INObjectif interchangeable En possession Interesse par Autres accessoires En possession Interesse parOBJETIVOS INTERCAMBIABLES EN POSESI6N INTERESADO EN OTROS ACCESORIOS EN POSESI6N INTERESADO EN

D D D D

D D D D

CUSTOMER~CliENTE

NAME ADDRESSNom AdresseNOMBRE DIRECCION _

CITY/STATE ZIP PHONE

~\ILelt;g~~~~ADO---------------g~ci'I&~~6sTAL- i~t~~~~o _

m'·TE~>

~~~~m~ CANON U.S.A., INC. CANON U.K.RCC<. A"r# CANON CANADA., INC. CANON AUSTRALIA PTY LTD.

NAMENOMNOMBRE

ADDRESSADRESSEDIRECCION

CANON NEW ZEALAND LTD. CANON LATIN AMERICA, INC.CANON SALES CO. JAPAN CANON MEXICANA

MODELMODELEMODELO

SPEEDLITE 580EX II

PURCHASE DATEDATE D'ACHATFECHA DE COMPRA

BODY NO.BOITIER NON" DE CUERPO

CITYVILLECIUDAD

PROVINCEPROVINCIA

POSTAL CODECODE POSTALC6DIGO POSTAL

THIS WARRANTY CARD AND YOUR BILL OF SALE MUST BEPRESENTED FOR WARRANTY SERVICE.

CETTE CARTE DE GARANTIE ET VOTRE PREUVE D·ACHAT DOIVENT~TRE PRESENTES POUR RECEVOIR LE SERVICE SOUS GARANTIE.

PRESENTE ESTA TARJETA DE GARANTIA Y LA BOLETA DE COMPRAPARA PODER RECIBIR EL SERVICIO DE GARANTIA.

DEALER'S NAME & ADDRESSMARCHAND NOM & ADRESSENOMBRE Y DIRECCION DEL DISTRIBUIDOR

Call0ll LIMITED WARRANTY Call011 GARANTIE LIMITEEThe Umited Warranty sel forth below Is given by CANON COMPANY listed below with respect to Canon Photographic Products purctlased in the United States. Canada, Australia, the UnitedKingdom, New Zealand. Mexico or Japan.This limited InternatiOnal Warranty is only effectJve upon presentation of the warranty card and prool 01 purchase.This canon equipment is warrantee! against defective materials or wort<manship for one (1) year lrom the dale of original purchase and Is limited 10 repair, adjustment and/or replacement ofdetective parts.Equipment covered by IhIs Warranty win be repaired by canon Internalional Warranty Members located In the United States, canada, Australia the United Kingdom, New Zealand, Mexico andJapan, WITHOUT CHARGE. (List of canon International Wamlnty Members included with the equipment.)EqlJlPlTl8nt covered by this Warranty wi" be repaired by Canon International Warranty Members WITHOUT CHARGE. excepl for Insurance. transportation and handling charges. (see list ofcanon International Warranty Members included with the equipment.)

When relurning equipmeollor warranty service, the shipping charges must be prepaid and the equipmenl should be shipped in its original carton or box, or an equivalent, property packed toWIthstand the hazards of shipment and be lully Insured. A copy 01 this warranty card and proof 01 purchase should be enclosed, as well as a description of the problem, film samples, elC.RepaIrs wII be made and the equipment will be returned, shipped al NO CHARGE within the country 01 repair.This warranty~ COV8fS defective materials or workmanship encountered In nannal use of the equipment and dOes not apply In the following cases:(a) Loss or damage 10 the equipment due 10 abuse causing deterioration, mishandling, accident or failure 10 follow operating instructions.(b) II equipmeot is defective es a result of leaking ballenas or liquid damage.(c) Delec1ive materials or workmanship where the defect is due 10 the equipmeot having been serviced or modifl8d by other than Canon International Warranty Members or other autOOri.zed

service facilities around the wOOd.(d) Mallunction resulting from the use 01 accessories, attachments, product supplies, parts or devk:es (including, without limitation, batteries, film, lenses, fiash attachments and other

acoessories) with Itus canon photographic equipment that do not cooforrn to Canon specifications.(e) Damage resulting during shipment. (Claim must be presented and examined by the shipper.)

Equipment oov8fecl by this warranty may be repaired by Canon Inlernational Warranty Members located outside the United States, canada, Australia, the United Kingdom. New Zealand,Mexico and Japan, WITHOUT CHARGE, except lor insurance, lransportation and handling charges. (Worldwide list 01 canon International Warranty Members included with equipment.)

CANON COMPANY EXCLUDES AlL REPRESENTATIONS, WARRANTIES, CONDITIONS OR LIABILITIES (WHETHER EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE) IN RELATION TO THE EOUIPMENT. EXCEPT THOSE WHICH ARE SET FORTH ABOVE AND/OR EXCEPT TO THE EXTENT THAT ANYSUCH EXCLUSION WOULD CONTRAVENE ANY STATUTE OR CAUSE THIS TERM TO BE VOID.EXCEPT TO THE EXTENT THAT ANY SUCH EXCLUSION WOULD CONTRAVENE ANY STATUTE OR CAUSE THIS TERM TO BE VOID, CANON COMPANY EXCLUDES ALL LIABILITYTO THE PURCHASER IN RESPECT OF ANY CLAIM (WHETHER CONTRACTUAL, TORTIOUS, STATUTORY OR OTHERWISE) FOR ANY GENERAL, SPECIAL, INCIDENTAL ORCONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE (INCLUDING, WITHOUT LIMITATION, ANY LOSS OF FILM) IN RELATION TO THE EQUIPMENT OR ANY SERVICESSUPPLIED BY CANON COMPANY IN RELATION TO THE EQUIPMENT. THIS WARRANTY SHAll NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THISEQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT.This WSlT8llty gives you specific legal rights. and you may also have other righls whtch vary fJom state to state, province 10 province and counlry 10 coontry.KEEP THIS WARRANTY CARD. IT IS YOUR PERMANENT RECORD OF WARRANTY. IF LOST IT Will NOT BE RE-ISSUED.·UrnIted Warranty means thai the contents of thiS warranty are limited to the above·mentlooed terms and conditions.

La garantie intemationale deeme d-dessous est accord8e par fa societe CANON al'egard des produlls de photograpnie Canon acheles aux Etats-Unis, au Canada, 8f'l Australie, au Royaume­Uni. 8f'l Nouvelle Zelande. au Mexique ou au Japan.La pnisente garantie intemationale n'est vallde que sur presentation de Ia carte de garantie el d'une preuve d'acha!.Le pr{lsent equlpement Canon esl garanti contre Ies vk:es de maleriaux au de fabrlcalion pendant une periods de un (1) an acompler de Ia date de I'achal initial. 51 I'equipemenl presente unech§fectuosile pendant Ia periOde de garantie, les pi(lCes defectueuses seronl r8par8eS, ~l8es et (ou) remplacees.l'equipemenl sous garantie sera repare SANS FRAIS par les membres du reseau moodial de faumisseurs de service sous garantie Inlernationale de canon, qui soot situes aux Etats-Unis, aucanada, en Australie, au Royaume-Uni, en Nouvelle Zelande, au Mexique et au Japan. (La lisle des membres du resesu mondial de loumisseurs de S8rv1ce sous garantie lntemationale deCanon accompagne 1'6Quipemenl.)Si Ie produit esl reloume pour lIlre repare ou rempLace au titre de fa garantie, l'exp6diteur du produil doit payer d'avance las lrai! d'exp&dition. L'8qulpemeol doil litre envoys dans sa bolteoriglnale, au dans un embaltage equivalent, 61re assure pour sa valeur IntegraJe, et il doit lltre embBlle adequatement pour evlter les rlsques de dommages en coors de transport. l'equipementdoll lltre accompagne d'une copie de Ia pniseme carte de garantie, d'une preuve d"achal aJnsl que d"uns description du pr~me, d"OChanUllons de pellicule ou de loute autre preove dech§lectuositll. Les reparations seront effectuees et I'equipemenl sera retoume a rexp8di!eur, SANS FAAIS, si radlesse de l'exp6diteur est dans Ie pave oil requipement a SiS rSpare.La presente garantie ne couvre QUe Ies vices de matllriaux et de fabrication survenus dans Ie cadre d"une utilisation normale de I'equlpemen!. Elle ne s'appIlque pas dans Ies cas suivants'

<a) perte de I'equipement ou dommage a I'equipement en raison d'un usage abusif menant ala deterioration. d'une manipulation inappropriM. dun accident ou de tout delaut de suivre lasdirectivesd'utillsation:

(b) dfIfectuosite altribuable a une fuile au nlYeau des piles ou dommages dus a une exposition a des substances Ilquldes;(c) vices de maler!aux ou de fabrication dus ala reparation ou ala modlflC8tion de 1'8qu!pemenl par un tiers, autre qu'un membre du reseau mondlal de loumisseurs de S8rvlce sous garantie

de canon, au aulre qu'un point de service autorisil au monde:(d) defam de fonctionnement decoulant de I'usage d'accessoires, de cornpI8menls, de loumitures, de pieces ou de disposltils (y compris, sans loulelois s'y Ilmil8f,1es piles, les pellicules, les

lenlilles, las lampes-8clairs el autres accessoires) qui sonl non conformss aux sp8cifications canon el qui soot utilisils avec eel equipement de photographie canon:(e) dommages subis en coors de transport (Toute r9damation dolt litre presentee el elC8mlnee par Ie transponeur.)

l'equlpement sous garantie paul litre repare SANS FRAIS par les membres du reseau morl(lial de laumisseurs de S8rv1ce sous garantie de CallOll qul ont une place d'affaires a l'elCler1eur desEtats-Unis, du canada, de l'Australia, du Royaume-Unl, de fa Nouvelle Z9lande, du Mex!que et du Japon, mais Ie pr0pri9talre de I'llqulpemern devra assumer les Irais d'assurance, de transportel de manulention. (La liste des membres du reseau mondlal de faumisseurs de service sous garantie de canon accompagne I'equipement.)LA SOCIETE:: CANON DE::CLARE QU'IL N'EXISTE, A l'EGARD DE CET EQUIPEMENT, AUCUNE AUTRE DE::CLARATION. GAAANTIE, COODITlON au OBLIGATION (EXPRESSE auTACITE, Y COMPRIS TOUTE GARANTIE DE OUALITE MARCHANDE OU DE CONVENANCE A UN USAGE PARTICULIER) QUE LA GARANTIE E::NONCEE CI·DESSUS, A MaiNSOU'UNE TELLE CLAUSE D'EXCLUSION N'ENFREGNE TOUTE LOI APPLICABLE au NE RENDE LA PRE::SENTE MODALrTE:: NULlE.A MaiNS OU'UNE TElLE CLAUSE D'EXCLUSION N'ENFREIGNE TooTE lOI APPLICABLE OU NE RENDE LA PRESENTE MODALlTE:: NUlLE, LA SOCIETE:: CANON N'ASSUMEAUCUNE RESPONSABILlTE:: AL'E::GARD DE TooTE RECLAMATION (DE NATURE CONTRACTUElLE, DE::L1CTUELLE, LE::GALE au AUTRE) FONDEE SUR TOUTE PERTE (Y COMPRIS,SANS TOUTEFOIS SY LIMITER, TOUTE PERTE DE PElLiCULE). TOUS OOMMAGES. TOUT COUT OU TOUS FRAIS DE NATURE GE::NE::RAlE, SPE::CIAlE, ACCESSOIRE OUINDIRECTE TOUCHANT l'eQU1PEMENT OU SUR TOUT SERVICE DISPENSE:: PAR lA SOCIE::TE:: CANON A L'E::GARD DE L'E::OUIPEMENT. LA PRESENTE GARANTIE NES'APPLIQUERA AAUCUNE AUTRE PERSONNE QUE L'ACHETEUR INITlAl DE CET E::OUIPEMENT OU LA PERSQNNE QUI l'A RECU EN CADEAU.La presente garantie vous confere des droits partlcutiers 8f'l vertu de fa Ioi. et Use peut que yous ayez d'autres droits QUi variant selon I'elat, Ia province 0I:l1e pays.VEUILlEZ CONSERVER LA PRE::SENTE CARTE DE GARANTIE. ELLE CONSTITUE UNE PREUVE PERMANENTE DE LA GARANTIE APPLICABlE A VOTRE EQUIPEMENT ET NE SERAPAS RE::EMISE EN CAS DE PERTE."La presenle garantle est qualiflee de limitee car son contenu est restreint aux modaJites et conditions deerites d-dessus.

Call0ll GARANTIA L1MITADALa garantla limltada estabIedda a contiouaci6n es otorgada por las empresas CANON COMPANY indicadas en la lista de abajo, para los produclos fotogrcUIcos canon comprados en losEstados Unidos, Canada, Auslralia, Reino Unido, Nueva Zelanda, Mexico 0 Jap60.Esta garantia inIemacional ~mitada sera electiva linicamenle conlra presenlad6n de Ia tarjeta de garantla y de una prueba fehaciente de Ia compra.EI equJpo canon estA garantizado contra defectos de material 0 de mano de obra bajo uso normal por un periodo de un (1) ai\o a partir de Ia lecha de compra original y se encuentra Hmilado aIa reparad6n, ajoste 0 susllIUcI6n y/o reempla20 de las piezas defectuosas.EI equipo cublefto pot esta garantla sem reparado pot los miembros de fa garantla inlemacional canon ubicados en los Estados Unidos, Canad<\. Australia. Reino Unido. Nueva Zelanda,canon latIn America, M.blco YJap6n SIN CARGO AlGUNO. (La Msta de los mlembros de Ia garantla intemaclonal canon que acompal'la aI equipo).EI equipo cubierto por esta garantls sen!. reparado por los mlembros de fa garanlla intemaciooal Canon, SIN CARGO AlGUNO, exeeplo para los gastos de seguro, lransporte y manejo.(Vilase Ia Iista de lTIiembfos de fa garanl/a Intemaclonal Canon que acompafla al equlpo).

Para poder recibir 91 serviclo de garantfa, usted debeni enviar el producto con tados los IIeles pagados de antemano en su caja de cartOn original 0 equivalente, debidamente empaquetadopara que pueda soponar los riesgos de transporte, y compIelameote asegurado. Sa debeni Incluir una copia de esta tarjeta de garantla y una prueba lehacieflte de fa compra, junto con unadescripci6n del problema, moeslras de peUCUlas, etcSa efectuaran las reparadones y e1llele de Ia devoIoci6n del equlpo sera SIN CARGO de!1tro del pais de reparad6n.Esta garantla cubre unicamente los defectos de material 0 de mano de obra bajo uso normal. y no sera apIicab1e en lOS siguientes casos:(a) Perdidas 0 daflos al 8QUlPO causados por deterioro resultanle del abuso. mal uso, accidente, 0 lalta de atendOn a las inslrucciones de funclooamiento.(b) oelectos del equlpo resultante de p&rdidas de electr61ito 0 de dai\os causados pot' el mismo.(c) oelecto de malerial 0 de mano de obra cuando ef defecto.sea resultado de modilicad6n 0 reparad6n reaUzada pot' personal distinto de los miembros de Ia garantla intemacional Canon u

otros ceotros de servlcio autorizados dislribuldos por todo eI mundo.(If) Failo de funcionamlento resultante de Ia utiWlaCl6o, junto con este equipo lotogoUico Canon, de accesorios, piezas de sujeci6n, consumibles del producto, repuestos 0 d4sp0sit/vos

(lI'lCluyendo, sin limitaci6n, pilas, pellculas, objetJvoS, aooesorios de !lash y otros accesorios) que no cumplan con las especificaclooes de canon.(e) Daflos provocados durante el transporte. (EI red8mO debe ser preS8ntado a y examioado pol' Ia empresa de transporte).

EI equipo CUbierto por esta garantfa puede S8l' reparado pol' los miembros de Ia garantla Intemacional canon ubicados fuera de Estados Unidos, canadA, AustraHa. Rero Unido, NuevaZelanda, Canon Latrn America, Mexico YJap6n SIN CARGO ALGUNO, exceplo para los gastos de seguro, lransporte y manejo. (La lista de los miembros de la garanlia intemacional canondel mundo que acompafla al eqwpo).

CANON COMPANY EXCLUYE TOOAS LAS REPRESENTACIONES, GARANTIAS, CONDICIONES U OBUGACIONES (SEA EXPRESA 0 IMPLICITA, INCLUYENOO COMERCIABllIDAD EIDONEIDAD PARA UN PAQPOSITO PARTICULAR) RELACIQNADAS CON El EOUIPO, EXCEPTO LO EXPRESAMENTE ESTABLECIDO EN El TEXTO PRECEDENTE YIO EXCEPTOHASTA El GRADO EN QUE AlGUNA EXCLUSI6N PUEDA INFRINGIR AlGUN ESTATUTO 0 CAUSAR LA ANULACI6N DE ESTOS TE::RMINOS.EXCEPTO HASTA EL GRADO EN QUE ALGUNA EXCLUSION PUEDA INFRINGIR ALGUN ESTATUTO 0 CAUSAR LA ANULACI6N DE ESTOS TE::RMINOS, CANON COMPANY NO

~E~L~ :~?~~ ~A5C~:g:~~~~~~~~I~t,~~I~~~~r ~~O~~~~E~~,!~~ ~E~~~~6'S~~~~~~g~~~~~~~~~~~~Ati~I~~~~~~~I~~~D~6A~T~:PEUCULA) .RELACIONADOS CON El EQUIPO 0 CUALESOUIER SERVICIOS SUMINISTRADOS POR CANON COMPANY EN RELACI6N CON El EOUIPO. ESTA GARANTIA SECONCEDE UNICAMENTE PARA EL COMPRAOOR ORIGINAL DE ESTE EQUIPO 0 PARA QUIEN FUERA ADOUIRlDO COMO REGAlO.

~t~fo'r~IST~~~.;;.~:~=I~~~I~~,rA~=~R~~~~~~8':,.~-rt~Nb~~~~~~~~~AaE~~deD~~~~~ncla,odepals a pals."Garantla limitada significa que eI conlenido de esta garanlla se encuenlra Iimitado a los lerminos y condiciones mencionados m4s arriba.

canon Australia Ply. Ltd. 1 Thomas Holt Drive, North Ayde, Sydney N.S.W.2113, AuatraliaCanon Canada. Inc. 6390 Dixie Road, Mlssissa0Q8, Ontario. L5T 1P7 CanadaCanon New Zealand Ltd. Akoranga Business Park, Akoranga Drive. Northcote. Auckland, New Zealandcanon UK RCC. Unil130 Centennial Park Elstree Hill South, Borehamwood Etstree. Hefts. WOO 3SE, United KingdomCanon U.S.A.. Inc. One Canon Plaza Lake success, NY 11042 U.S.A.Canon Mexicana S.DE R.LDE C.V. Blvd. Manuel Avila camacho No. 138 Col. lomas de Chapunepec C.P. 11000 MexIco D.F., MEXICOCanon Latin America. Inc. Miami 703 Waterlord Way Suite 400, Miami, FL 33126 U.S.A.Canon 8aJes Co. Japan 2-16-6, Kohnen, Minato-ku, Tokyo 108-8011, Japan