manual doorcom ip dcip 600-0 - siedle · 2019. 2. 7. · dcip 600-0 4 group calculation max. number...

ManualDoorCom IP

DCIP 600-0

2

Contents

1 System description 3

2 Safety remarks 3System requirements 3

3 StructureDCIP 600-0 4Group calculation Max. number of PC users 6Terms 6

4 Components Calling 8Input module, camera module 9Power supply, programming, IP video server 10Software 11System-free operation 12

5 InstallationWiring diagrams DCIP 600-0Terminals DCIP 600-0 14LED display SIVS 600-... / IPVS 600-... 15Block diagrams 16DCIP 600-... up to 4 users 18DCIP 600-... with DCA 740-... 20DCIP 600-... with TME 645-... 22DCIP 600-... with COM 611-... 24DCIP 600-... withCOM 611-... and AEM 645-... 26DCIP 600-... with DRM 611-... 28

6 CommissioningDCIP 600-... 30Multicasting 31Configuration software DCIP CO 32Software client DCIP SC 34

7 Setting the speech volume, level adjustmentDCIP 600-... 36

8 DoorCom DCA 740-01 38

9 Factory reset 38

10 DoorCom IP FAQ andtrouble shooting 39

11 Glossary, index 41

3

DoorCom IP 600-0Siedle DoorCom IP links the Siedle world of building communication to the IP world. Door calls are transformed via the DoorCom IP and transmitted via the IP network to certain PCs. If video cameras are fitted at the door station, the picture of the visitor is additionally transmitted. The DoorCom IP Software Client is used here as a virtual in-house telephone for communication to the door station.The Software Client must be installed on every PC in the network which is intended to receive a door call. Assignment of door calls to the Software Clients takes place using an IWA address (Interface Working Address) which is entered in the DoorCom IP with the aid of the configuration software.

DCIP 600-0The DoorCom IP 600-... links the Siedle door loudspeaker Line-LevelTLM/LL 611-... and the camera module CMM/CMC 612-... to an IP network (10/100/1000 Mbit) on a system-free basis.

The DoorCom IP is able to display the picture on the PC monitor in conjunction with the Siedle Software Client and at the same time hold the door call via the PC. The door call can optionally also be held over the telephone system using a telephone, while the picture is displayed by the Software Client and all control functions such as door release can also be initiated by the software. For this, a DCA 740-01 must additionally be connected to the DoorCom IP.

Danger

Mounting, installation and servicing work on electrical devices may only be performed by a suitably qualified electrician. Failure to observe this regulation could result in the risk of serious damage to health or fatal injury due to electric shocks.• When working at the device, observe the instructions for mains cut-off.• Observe the standard DIN EN 60065!When establishing the electronic connection, observe the requirements of VDE 0805 / EN 60950.• An all-pole mains switch must be provided in the building installation with a contact openingof at least 3 mm.• Ensure that the connection point in the building installation is fused with max. 16 A.• When planning, the required distributor space for switch panel mounted devices must be taken into account. • External voltages >30 V AC/ DC must not be injected into the in-house telephones.

Devices with 230 V connectionIn accordance with DIN VDE 0100 Part 410, Section 411.1.3 ensure that the DoorCom installation and the mains voltage are securely isolated. The sheathing of the connection cable (safety extra-low voltage) should only be stripped back far enough to ensure that reliable connection is possible.

For mains connection ! and network settings such as assignment of the IP address, the responsible network administrator must be consulted.

1 System descriptionDoorCom IP 600-0

2 Safety remarksSystem requirements

Find out about the necessary safety measures and system requirements before starting installation and commissioning of the DoorCom IP.

System requirementsfor the configuration software • PC with Intel Pentium III from 1 GHz or comparable processor• at least 256 MB RAM• min. 25 MB hard disk memory• Serial COM interface RS232 or USB interface• CD-ROM drive for installation • VGA graphic card withat least 1024 x 768 pixel• Operating system Windows 2000/XP• Admin rights for installationAdditional memory capacity is required for:• Acrobat Reader 7• Microsoft Internet Explorer from version 4

System requirementsfor the Software Client• Operating system MicrosoftWindows 2000/XP• Pentium IV from 1.8 GHz or compatible CPUs• min. 256 MB RAM• Graphic card with at least 1024 x 768, 128 MB and 16 bit colour depth MPEG 4 capability• 100 Mbit Ethernet card• Sound card• Microsoft DirectX 9.0b or newer• Microsoft Internet Explorerfrom version 4.0 for reading the help

Speech qualityThe audio quality (speech transmission) is highly dependent on the quality of the audio components built into the PC (headset, handset and sound card).

4

3 Structure DCIP 600-0System-free

DCIP 600-...System-free linkThe DoorCom IP 600-... serves as an interface between a system-free Siedle door station and an IP network. In conjunction with the DoorCom IP Software Client, which serves as a virtual in-house telephone, the door call (incl. video) can be held via the PC. The door call can optionally also be held via the telephone system with a telephone. For this purpose, an additional DCA 740-01 must be installed. Link-up of the DCA 740-01 takes place via a free a/b port of the telephone system. The video camera image continues to appear on the PC monitor, control functions such as the door release can still be operated via the Software Client.

The DCIP 600-... comprises the components:• SIVS 600-.., system interface video server. Processing and adjustment of data, through connection of audio and video signals.• IPVS 600- .., IP video server. Processing and adjustment of audio and video, transmission of data,

audio and video to the IP network.One DCIP 600-... each is required per door. A maximum of 49 different call destinations can be dialled. Dialling is possible by means of a call button module, code lock module or display call module.• Configuration software DCIP CO 600-... for configuration of the SIVS 600-...• Software Client DCIP SC 600-... for installation on PC users intended to receive door calls.

Power supplyThe DCIP 600-... SET works with 24–28 V supply voltage. An optionally connected DCA 740-01 is supplied from the SIVS 600-... . The a/b public network interface is supplied from the TC system. It is not possible to connect an individual public network telephone directly to the a/b line of the DCA 740-01. The DCIP 600-... or the IPVS 600-... is linked using a standard network cable with RJ45 plug to the IP network (10/100).

Functions of the Software Client• Door calls and signalling on the PC

• Text display of which door is calling. • Door release actuation by means of a mouse click• Light actuation by means of a mouse click• Muting of the ring tone by means of a mouse click• Selective connection to a door station• Parallel door call to up to 25 PC clients simultaneously• Speech connection via PC (e.g. headset) or optionally via the telephone of a telephone system.• Almost any optional number of doors can be connectedCommissioning and programmingAfter connection of the supply voltage, the SIVS 600-... can be programmed with the aid of a PRI 602-... USB and configuration software DCIP CO 600-... via the PC. No additional programming is required for the optional DCA 740-01. For programming / configuration of the TC system, see the relevant product information and programming instructions of the TC manufacturer.

PRI 602-... USBNG 600-0

5

Mounting and installationThe devices are intended for switch panel mounting. These should preferably be mounted directly one next to the other. The maximum conductor length between the devices must not exceed 1 metre. Actuation of the link between the SIVS 600-... and the IPVS 600-... takes place via the supplied cable. The system interface video server SIVS 600-... processes the control signals from the door station for the RS232 interface and switches through the audio and video signals in the case of a connection. The processed signals are transferred to the IP video server IPVS 600-... . The IPVS 600-... transforms the data, audio and video signals and establishes communication to the TCP/IP network. One or more PCs (up to max. 49) can be called from the door station within a network. The Software Client must be installed for door communication on every PC which is intended to receive a door call. The sound card and headset are required to set up a call. The door call can optionally also be held via a telephone system using

a telephone with DTMF capability. For this purpose, the DCA 740-01 must additionally be installed at an analog PBX extension of a telephone system.One DCIP 600-... each is required per door station. This can be used to call a maximum of 49 different users.

For 4 PC users, the Software Client is included in the scope of delivery of the DCIP 600-... . Each additional PC user requires a licence for the Software Client DCIP SC 600-0.

DCIP 600-... System-free link with connection of a telephone systemPerformance features• Transmission of door calls with/without video via the IP network to PC users• Optionally: Audio transmission via telephone network (DCA 740-01) in parallel to the video signal via Ethernet • Full duplex link during door calls (no push-to-talk simplex communication with button actuation)

• Control commands such as door release and light possible from the PC with a mouse click• Video: MPEG-4 (ISO/IEC 14496) Codec, Audio: G.711; (300Hz - 3.4KHz)• The DoorCom IP manages up to 49 different PC users• Parallel call to up to 25 PC users possible• Selective connection to a door station. (Audio and/or video) • Combination with code lock module COM 611-... or display call module DRM 611-... possible for direct calls to PC users.• Using the TME 645-..., more than 4 call stations can be connected.

3 Structure DCIP 600-0System-free with link to telephone system DCA 740-01

PRI 602-... USBNG 600-0

6

3 Terms

ClientPC user connected to a network.

Full duplexBoth users (PC client and door station) have an unrestricted speech connection. Open duplex communication, i.e. as opposed to the simplex speech mode.

GatewayGateways link two different networks and create connections across network boundaries. During this process, both the physical transmission modes and also protocols and addresses are adjusted accordingly.

Half duplexTwo speaking users have one speech connection which they can use alternately, also known as push to talk.

HTTPThe Hypertext Transfer Protocol is a protocol used for the transmission of data via a network. It is used mainly to load websites and other data from the Internet into a web browser.

HubThe term hub when used in relation to network technology describes a device which links network nodes in a star formation. Normally, the term hub is used to denote a multiport repeater. It is used in order to link network nodes or other hubs, for example by means of an Ethernet.

IP addressInternet Protocol addressAn IP address is a number which permits PCs and other devices in an IP network to be addressed. In technical terms, the number is a 32- or 128-bit binary number.IPInternet Protocol The IP is a network protocol in widespread use in computer networks. IP forms the first layer of the Internet protocol family which

For calculation of the maximum number of possible PC users (single and parallel calls), the following rules are applied:• In general, an IPVS can manage a maximum of 50 registrations. • Every PC user to which a door call has been established currently occu-pies 2 registrations in the IPVS.• If no groups are created, a maximum of 49 single PC users can be integrated. If one of these PC users is called, it currently occupies 2 registrations, the others occupy only one each. In total, this adds up to 1*2+48=50, which is the maximum possible assignment per IPVS.• If several groups are created, the biggest group is decisive for the calculation. The maximum group size is 25. If this group is called, each PC user currently occupies 2 registrations. In total, this adds up to 25*2=50, which is the maximum possible assignment per IPVS.

In the following is a list with five combinations. Each example compri-ses a group with a different number of users and individual clients.

Clients in group

Individual Clients

Calculation

5 40 5*2+40=50

10 30 10*2+30=50

15 20 15*2+20=50

20 10 20*2+10=50

25 0 25*2+0=50

Example in case of several groups:The following is a combination example comprising two groups and five individual clients, with each group and each individual client occupying one address. Consequent-ly a total of seven addresses are used in the system.Group 1: 20 PC users Group 2: 5 PC users Clients: 5 individual PC users • If the biggest group (group 1) is called, this group occupies 20*2=40 registrations in the IPVS. Group 2

and the individual PC users each occupy 5 registrations. In total, this adds up to 20*2+5+5=50, which is the maximum possible assignment per IPVS.

For parallel calls to groups, note the section on multicasting, page 31.

3 Group calculation Max. number of PC users

7

is independent of the transmission medium. This means that computers can be grouped within a network into logical units known as subnets by means of an IP address and subnet mask.

IWAInterface Working Address Six-digit address with which the system interface video server SIVS 600-... addresses the PC users. These IWA addresses are stored in the Software Client.

LANLocal Area Network Local, cable-linked network.

MulticastingTerm to denote group/parallel calls with video image to several PC users which have the Software Client installed. For this to be possible, the UDP and IGMP V3 protocols must be implemented in the network.

Push to TalkIn case of a connection using the half-duplex mode (push to talk) a button always has to be pushed to change the speech direction.

RouterA router is a network device which links several computer networks. Network packages of a protocol arriving at the router are analysed for information and forwarded or routed to the intended destination network.

RS232Designation for a serial interface, for instance the COM interface of a PC.

RS485Interface for serial data transmission in the half-duplex mode. Transmission to a pair of cores.

ServerA server is a program which waits to be contacted by a client program, after which it exchanges data with the client program. The hardware

on which the server runs is known as the host.

Subnet maskThe subnet mask, also known as network mask, is a bit mask which separates an IP address into a network and a device or host section. It is used in IP networks in order to make routing decisions.

System-freeThe DCIP 600-... is operated with a system-free connection. This means that the door loudspeaker works with line signals. No system-specific door loudspeaker is used, for instance the TLM 612-...

TCPTransmission Control Protocol The TCP is a protocol which determines the way in which data is exchanged between computers. All operating systems in modern computers have TCP capability and use this protocol for data exchange with other computers. The protocol is a reliable, connection-oriented transport protocol used in computer networks.It is part of the internet protocol family, which forms the foundation of the Internet.

UDPUser Datagram Protocol The UDP is a minimal connectionless network protocol which belongs to the transport layer of the Internet protocol family. It is the task of the UDP to assign data transmitted via the network to the right application.

Vario busVarious different input and control units can be connected to the Vario bus. It comprises 4 cores. The Vario bus is a RS485-bus. The information will be transfered on the Vario bus protocol.

Web browserSoftware for the display and indication of Internet pages or corresponding configuration pages. E.g. Internet Explorer or Firefox.

8

TME 640-0Call button module extension in protective housing with screw terminals, for connection of call button modules TM 612-... or call buttons of other makes.A maximum of 16 call button modules can be connected to the TME 640-… by means of a matrix installation.Dimensions: 100 x 50 x 20 mm

cable. Dimensions: 99 x 99 mm

TM 612-1 - TM 612-4Call button modules, potential-free buttons, 1-4 call buttons, integrated LED lighting. Connection by means of terminal block. Power supply to the LED lighting by means of terminal b and c with 12 V AC/DC, current consumption 25 mA per call button module TM 612-...Used as call buttons 1-4 directly at the SIVS 600-...

TME 645-0Call button module extension with interface to the Vario bus for max. 8 TME 645-... . Suitable for connection of call button module BTM 650 -... A maximum of 16 bus call button modules can be connected per TME 645-… . With an acoustic signal which sounds on button assignment. The call button modules are connected to the TME 645-… by means of a ribbon

4 Components for DCIP 600-...Call buttons

BTM 650-01 - BTM 650-04Bus call button modules for In-Home bus. 1-4 call buttons, integrated LED lighting. Connection via ribbon cable to the TME 645-... Power supply to the LED lighting via terminals b and c with 12 V AC/DC, current consumption 25 mA per bus call button module BTM 650-...

9

CMC 612-...Camera module, colour. Integrated 2-step heating system, day/night switchover, infrared lighting and video signal transformer. Power supply using line rectifier NG 600-... or VNG 602-... With Siedle Multi via PCM 640-.../NG 600-..., NG 608-... or NG 640-... Heating power supply 12 V AC, 100 mA.

COM 611-01Code lock module as an input unit in conjunction with the Siedle Vario bus. A C button for deleting incorrect inputs. LED as status display (external potential-free contact). Operating voltage 12 V AC /DCCurrent consumption max. 100 mA

Ambient temperatue -20°C to +70°C Dimensions: 99 x 99 mm

AEM 645-0Alphabetical input module with keypad A - I. Input unit for alphanumerical selection of PC users. For use in Siedle Multi systems only in conjunction with the TLC 640-02, COM 611-01 DIM 640-0 and SIVS 600-...Operating voltage 12 V AC /DCCurrent consumption max. 100 mA

4 Components for DCIP 600-...Input module, camera module

DRM 611-0Display call module as an input unit with 4-line display for placing door calls.To scroll through the name index, there are two arrow keys provided for „up/down“. An external DR button can be connected. • 4-line display x 18 characters each, with LED backlighting• 3 displacement-free piezo buttons • Button actuation confirmed by

acoustic tone• Backlit symbolsOperating voltage 12V AC/DC• Current consumption max. 200 mAAmbient temperature -20°C to +70°C Dimensions: 99 x 99 mm

10

4 Components for DCIP 600-...Power supply, programming, video server

NG 600-0Line rectifier in 10-grid switch panel housing for universal power supply. Suitable for surface mounting with ZAP 10-0. Primary 230 V AC, 50 Hz, +6%-10%Secondary b/c: 14 V AC, 1 A; +/-: 24-28 V DC, 0.7 A Ambient temperature 0°C to +40°C, protection rating IP 20Dimensions: 180 x 89 x 60 mm

PRI 602-... USBProgramming interface for connection of a Windows PC via USB interface to the Vario bus. Required for configuration of the system interface video server with software DCIP CO 600-... version 1.1. or higher.

IPVS 600-0System interface video server Processing and adjustment of audio and video, transmission of data, audio and video to the IP network.Dimensions 112 x 85 x 40 mm

DCA 740-01The DoorCom Analog DCA 740-01 can be connected to a universal a/b interface. In conjunction with the DCIP 600/740-... it serves as an alternative speech connection if no speech connection via PC is preferred. Connection takes place at the standardized a/b interface of a TC system (analogue PBX extension) or directly at the analogue telephone network.Dimensions: 107 x 89 x 60 mm

11

DCIP SC 600-0DoorCom IP Software Client PC program, which depicts a virtual house telephone with video on a PC monitor. Door calls with video are possible to one or more Siedle door stations.Execution of switching and control functions such as door release, light switch or display of messages on the PC monitor.For each installation of the Software

DCIP CO 600-0DoorCom IP configuration software PC program for set-up and programming of the Siedle interface video server SIVS 600-...Programming takes place via the USB programming interface PRI 602-...USB configuration software version 1.1. or higher.

Commissioning software for the administrator.

CD contains• DoorCom IP Software Client(DCIP SC 600-0)• DoorCom IP Configuration software (DCIP CO 600-0)• DoorCom IP Manual• Siedle default configuration for IPVS 600-...• Java Runtime Environment (JRE) 5.0• Microsoft Installer 3.1

Client on a PC, a licence is required for the DCIP SC 600-0.

4 Device overview for DCIP 600-...Software

12

4 Device overview only DCIP 600-...System-free operation

SIVS 600-0System interface video server for connection of the TLM/LL 611-...Conversion of signals from the door loudspeaker to the IPVS 600-0. Manages assignment, i.e. how which PC is called. Connection of modules COM 611-..., AEM 645-..., TME 645-... or DRM 611-... possible. Dimensions 144 x 130 x 55 mm

TLM/LL 611-01Door loudspeaker module for interfacing at a symmetrical or asymmetrical line interface, with integrated electret microphone and loudspeaker. Integrated echo compensation for full duplex operation. Potential-free light button capable of illumination, and controllable volume.

Power supply 15-28 V DCmax. 100 mALine-In 800 mVeffImpedance 2 kOhmLine-Out 100 mVeff Impedance 100 Ohm

14

5 TerminalsDCIP 600-...

a b c

d e f g

Terminals and LEDs IPVS 600-0a No functionb Connecting socket to the SIVS 600-...c RJ45 socket ETH network connectiond Reset button to recreate the as-delivered status (after a reset, the Siedle modes must be reinstalled, see page 38.)e LED operating status lights up in green on readiness for operationf LED L lights up in green with an existing network connectiong LED T flashes orange on data transmission via the network

Terminals IPVS 600-0h Video input 1Vss from the SIVS 600-...i Audio-Line-In to the SIVS 600-...j Terminal plug for control signalsk Audio-Line-Out to the SIVS 600-...

TerminalsSIVS 600-...a Video signal 1 Vss (cinch jack)b Terminating resistor 75 Ohm ON/OFFc IN = video signal 1 Vss input,D = Video signal 1 Vss throughputd Terminals for installatione Connection to IPVS 600-...f Terminals for installationg Grounding terminal

a

b

c

d

e

f

g

h i j k

15

5 LED displaySIVS 600-.../IPVS 600-...

LED signalling SIVS 600-...

Switching on LED green LED red FunctionOFF ON After reset, power on: Device boots to operating status.ON ON The boot area is checked. Software runs in the flashFast flashing ON After a software update, the boot area is recreated. This can take up to around 3 minutes.

Operation

LED green LED red FunctionON OFF Booting is complete. All OK. Normal status Slow flashing OFF Display, a connection existsFast flashing OFF A software update or reconfiguration process is under way

Fault

LED green LED red FunctionOFF Slow flashing ERROR, software running only in bootloader. Program memory defective. (Device defective, possibly new software update or exchange.)ON Slow flashing Variobus address error (error remedy possible on site)ON Fast flashing The 15 V power supply (terminal bv, cv) is overloaded. (Error remedy possible on site)OFF OFF If supply voltage is definitely connected, the device is defective. (Exchange)

Frequencies: Slow appr. 2 Hz, fast appr. 16 Hz

LED signalling IPVS 600-...

The underneath of the IP video server IPVS 600-... has 3 LEDs which display operating statuses and can provide an indication of possible errors.

LED operating status FunctionOFF IPVS 600-... is switched off.Lights up in green IPVS 600-... is switched onFlashes green Access to the IPVS 600-...Lights up in red (briefly) Start process runningLights up in red (continuous) Error in the device or failed upload

LED LLights up in green Network connection exists

LED TLights up in orange Active data transmission via the network

16

5 TerminalsSIVS 600-0, TLM/LL 611-01

Block diagramSIVS 600-0

G Reference for inputs E1–E4E4 Input 4E3 Input 3E2 Input 2E1 Input 1cv- Supply voltage forbv+ Vario bus, 15 V DC, max. 300 mADa/Db Vario bus+ Supply voltage- 24 V DCTö Door release contact potentialTö Free max. 24 V, 1 ALi Light contactUSP Universal Switch Port bn1 Line signal to the door station,bn2 outgoingan1 Line signal from an2 door station, incomingn1 NF signal for n2 connected DCA 740-01

Block diagram TLM/LL 611-01

+ Terminal for - supply voltageL- Lighting, light buttonan1 Microphone signalan2Mu Muting bn1 Loudspeaker signalbn2T1 Potential-free contact T2 Light button, max, 24 V, 2 A

17

Block diagram CMC 612-0

+M/-M Supply voltage Video 20 - 30 V DCVc/- Actuation from door loudspeaker for camera on. With DoorCom IP the contact is permanently active. Potential - is switched via the UPS terminal.VKA Actuation of camera distributor -M is switchedA1/A1 Potential-free contact for additional applicationsb/c Power supply 12 V AC for heating

5 TerminalsCMC 612-0

18

Devicerequirement

Remarks

red

black

5 InstallationDCIP 600-... system-free up to 4 users

19

DCIP 600-... system-free up to 4 users

Functional characteristicsUp to 4 PC users (Software Clients) of a network can be called from the door station, with a direct connected button module e.g. TM 612-4. Calling, speech and door release via the Software Client DCIP SC 600-... . The Software Client must be installed on every PC which receives door calls. Standard call tones for the Software Client 3-tone chime. A dedicated *.wav file can be assigned for each call tone.It is not possible to listen in to an existing call from other PC users in the network.The door is opened by the called PC user using a “virtual door release button”, the light switching function is actuated using a “virtual light button”. The door call can be muted with an optical display on the monitor.

Supplementary functions• With additional TME 645-... units, up to 49 users are possible.• Connection of the COM 611-... is possible in order to call a maximum of 49 PC users by means of code selection.• Up to 25 PC users can be called in parallel with a call button from the door station.• Every PC user to which a door call has been established occupies currently 2 registrations in the IPVS.

Remarksa) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...)b) The NG 600-0 can also take over the power supply to existing on-site call buttons. A voltage of 12 V AC max. 200 mA is available for the lighting if a door release with an impedance of at least 20 Ohm is used. With a higher current consumption, an additional transformer must be used.• 12 V AC consumers in the wiring diagram:• Door release appr. 600 mACamera heating appr. 100 mA• Door release contact load in the SIVS 600-... max. 24 V AC, 1 A• Light contact load in the door loudspeaker max. 24 V AC, 2 Ac) Distance of the SIVS 600-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 600-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable.Power supply voltage bv+/cv- of the SIVS 600 15 V DC, max. 300 mAd) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the software client can still be used.

20

5 InstallationDCIP 600-... system-free up to 4 users with DCA 740-...

21

DCIP 600-... system-free up to 4 users with DCA 740-01

Functional characteristicsUp to 4 PC users (Software Clients) of a network can be called from the door station, with a direct connected button module e.g. TM 612-4. Calling, speech and door release via the Software Client DCIP SC 600-... . The Software Client must be installed on every PC which receives door calls. Door calls are additionally routed to the analogue PBX extension of a telephone system. This task is assumed by the DCA 740-... The video image is still displayed through the Software Client and all control functions such as the door release are also performed via the PC. The speech connection is established via the DCA 740-... and the telephone system.

Standard call tones for the Software Client 3-tone chime. A dedicated *.wav file can be assigned for each call tone.It is not possible to listen in to an existing call from other PC users in the network.The door is opened by the called PC user using a “virtual door release button”, the light switching function is actuated using a “virtual light button”. The door call can be muted with an optical display on the monitor.

Supplementary functions• With additional TME 645-... units, up to 49 users are possible.• Connection of the COM 611-... is possible in order to call a maximum of 49 PC users by means of code selection.• Up to 25 PC users can be called in parallel with a call button from the door station. • Every PC user to which a door call has been established occupies currently 2 registrations in the IPVS.

Remarksa) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...)b) The NG 600-0 can also take over the power supply to existing on-site call buttons. A voltage of 12 V AC max. 200 mA is available for the lighting if a door release with an impedance of at least 20 Ohm is used. With a higher current consumption, an additional transformer must be used.• 12 V AC consumers in the wiring diagram:• Door release appr. 600 mA Camera heating appr. 100 mA• Door release contact load in the SIVS 600-... max. 24 V AC, 1 A• Light contact load in the door loudspeaker max. 24 V AC, 2 Ac) Distance of the SIVS 600-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 600-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable.Power supply to the SIVS 600 15 V DC (terminal bv+/cv-), max. 300 mA.d) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the software client can still be used.

22

5 InstallationDCIP 600-... system-free up to 49 users

23

The first bus call button module BTM 650-... is plugged into the TME 645-... . All additional bus call button modules BTM 650-... are interconnected with IN/OUT.

DCIP 600-... system-free up to 49 users with TME 645-...

Functional characteristicsUp to 49 PC users (Software Clients) of a network can be called from the door station. Calling, speech and door release via the Software Client DCIP SC 600-... . The Software Client must be installed on every PC which receives door calls. Each PC user must hold a valid licence for the Software Client.


Supplementary functions• Connection of the COM 611-... is possible in order to call PC users by means of code selection.• Up to 25 PC users can be called in parallel with a call button from the door station.• Every PC user to which a door call has been established occupies currently 2 registrations in the IPVS.

Remarksa) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...)b) The NG 600-0 can also take over the power supply to existing on-site call buttons. A voltage of 12 V AC max. 200 mA is available for the lighting if a door release with an impedance of at least 20 Ohm is used. With a higher current consumption, an additional transformer must be used.• 12 V AC consumers in the wiring diagram:• Door release appr. 600 mA Camera heating appr. 100 mA• Door release contact load in the SIVS 600-... max. 24 V AC, 1 A• Light contact load in the door

loudspeaker max. 24 V AC, 2 Ac) Distance of the SIVS 600-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 600-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable.Power supply to the SIVS 600 15 V DC (terminal bv+/cv-), max. 300 mA.d) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the Software Client can still be used.

24

5 InstallationDCIP 600-... system-free with COM 611-...

25

DCIP 600-... system-free with COM 611-...

Functional characteristicsUp to 49 PC users (Software Clients) of a network can be called from the door station via the code lock. Calling, speech and door release via the Software Client DCIP SC 600-... The Software Client must be installed on every PC which receives calls. For calls via the code lock module, for each user a freely selectable call number (max. 22 digits) can be entered. The call numbers can agree, for instance, with an existing telephone directory.


Supplementary functions• Up to 25 PC users can be called in parallel with a call button from the door station.• Every PC user to which a door call has been established occupies currently 2 registrations in the IPVS.

Remarksa) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...)b) The NG 600-0 can also take over the power supply to existing on-site call buttons. A voltage of 12 V AC max. 200 mA is available for the lighting if a door release with an impedance of at least 20 Ohm is used. With a higher current consumption, an additional transformer must be used.• 12 V AC consumers in the wiring diagram:• Door release appr. 600 mA Camera heating appr. 100 mA• Door release contact load in the SIVS 600-... max. 24 V AC, 1 A• Light contact load in the door loudspeaker max. 24 V AC, 2 Ac) Distance of the SIVS 600-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 600-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable.Power supply to the SIVS 600 15 V DC (terminal bv+/cv-), max. 300 mA.d) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the Software Client can still be used.

26

5 InstallationDCIP 600-... system-free with COM 611-... and AEM 645-...

27

DCIP 600-... system-free with COM 611-... and AEM 645-...

Functional characteristicsUp to 49 PC users (Software Clients) of a network can be called from the door station. Calling, speech and door release via the Software Client DCIP SC 600-... . The Software Client must be installed on every PC which receives door calls.For calls via the code lock module, for each user a freely selectable call number (max. 22 digits) can be entered. The call numbers can agree, for instance, with an existing telephone directory.


Supplementary functions• Up to 25 PC users can be called in parallel with a call button from the door station. • Every PC user to which a door call has been established occupies currently 2 registrations in the IPVS.

Remarksa) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...)b) The NG 600-0 can also take over the power supply to existing on-site call buttons. A voltage of 12 V AC max. 200 mA is available for the lighting if a door release with an impedance of at least 20 Ohm is used. With a higher current consumption, an additional transformer must be used.• 12 V AC consumers in the wiring diagram:• Door release appr. 600 mA Camera heating appr. 100 mA• Door release contact load in the SIVS 600-... max. 24 V AC, 1 A• Light contact load in the door loudspeaker max. 24 V AC, 2 Ac) Distance of the SIVS 600-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 600-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable.Power supply to the SIVS 600 15 V DC (terminal bv+/cv-), max. 300 mA.d) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the Software Client can still be used.

28

5 InstallationDCIP 600-... system-free with DRM 611-...

29

DCIP 600-... system-free with DRM 611-...

Functional characteristicsUp to 49 PC users (Software Clients) of a network can be called from the door station. Calling, speech and door release via the Software Client DCIP SC 600-... The Software Client must be installed on every PC which receives door calls. For calls via the display call module, a name can be assigned to each PC user, e.g. Anton Anyone.To scroll through the name index, there are two arrow keys provided for „up/down“. When the required name is highlighted in the list, pressing the button with the bell symbol will initiate a call to this user. The DRM 611-… can also be used in combination with the COM 611-… in order to display the input via the DRM 611-...


Supplementary functions• Connection of the COM 611-... is possible in order to call PC users by means of code selection.• Up to 25 PC users can be called in parallel with a call button from the door station.• Every PC user to which a door call has been established occupies currently 2 registrations in the IPVS.

Remarksa) Door release 12 V AC, use at least 20 Ohm (e.g. TÖ 615-...)b) The NG 600-0 can also take over the power supply to existing on-site call buttons. A voltage of 12 V AC max. 200 mA is available for the lighting if a door release with an impedance of at least 20 Ohm is used. With a higher current consumption, an additional transformer must be used.• 12 V AC consumers in the wiring diagram:• Door release appr. 600 mA Camera heating appr. 100 mA• Door release contact load in the SIVS 600-... max. 24 V AC, 1 A• Light contact load in the door loudspeaker max. 24 V AC, 2 Ac) Distance of the SIVS 600-... to the door station max. 200 m with J-Y(ST)Y 0.8 mm core material. Distance between the two devices SIVS 600-... and IPVS 600-... in the distributor max. 1 m. During installation, ensure that the door release is laid in a separate cable.Power supply to the SIVS 600 15 V DC (terminal bv+/cv-), max. 300 mA.When connecting additional devices to the Vario bus (terminals Da/Db), the Vario bus requires an additional power supply.d) ***Optionally the DCA 740-01 can be connected to the PBX extension of a telephone system. Active door calls can then be routed via the telephone. The functional features of the Software Client can still be used.

30

Commissioning of the DCIP 600-... is broken down into three steps:1 Configuration of IPVS 600-...2 Configuration of SIVS 600-...3 Installation of the software DCIP SC 600-... on the PCs

Step 1 on this pageConfiguration of IPVS 600-...Issue of the IP address, subnet mask address and gateway address for assignment in the network. In case of group calls, issue of the Multicast address.

Step 2 on pages 32Configuration of SIVS 600-...Assignment of the IWA addresses from the call buttons to the subsequent PC users. When using additional modules such as the code lock module or display call module, these are also configured at this stage. After completion of programming, a file (*.dcip) is created for the Software Client.

Step 2.1Configuraion of DRM 611-...Names are programmed with the PRS-Software. The correspronding numbers are also entered here.

Step 2.2Configuration of DCA 740-...The DCA 740-... will not be confi-gured. The numbers are given in the DCIP configuration programm, by activating the DCA 740 and entering the phone numbers.

Step 3 on pages 34Installation of the Software ClientsThe Software Client has to be installed on the PC users in the network. Import of the generated file (*.dcip). Selection of addresses to be signalled on the affected PC user.

6 CommissioningDCIP 600-... system-free

Step 1Issue of the IP address and subnet mask in the IPVS 600-...• The connection can be established using a crossover network cable. The IPVS 600-... can also be addressed via the network if the PC and IPVS 600-.. are located in the same address area.• Start the Internet Explorer on the PC and enter the following in the address line:http://192.168.0.1The IP settings in the as-delivered status of the IPVS 600-...IP address 192.168.0.1Subnet mask 255.255.255.0Gateway address 0.0.0.0User name: ServicingPassword: None issued on delivery• The user interface is opened.• In the user interface, select the menu point Settings.• On the left-hand side, select the menu point Service parameters.• Click the submenu Network . On the right-hand side, the relevant settings are opened up.• The following settings can be performed for operation in the network.IP addressSubnet mask addressVideo transmissionHTTP browser portType of network connection

Connection of the PC to IPVS 600-...

Changes to the IP address or subnet mask address are transmitted to the device by clicking on the Set button. However, these only become valid after restarting the device.

• After entering a new IP address, click onto the Set button.• Enter the old IP address in the address line of the web browser, followed by /reset (for example 192.168.0.1/reset). The IPVS is restarted and can subsequently only be reached using the new IP address.

31

6 ConfigurationMulticasting

MulticastingAlongside the 1:1 connection between one IPVS 600-... and one software client (Unicast) each, the IPVS 600-... also offers facility for several software clients to receive the video signal at the same time. This takes place either by duplicating the data stream in the IPVS 600-... and subsequent distribution over several software clients (multi-unicasting) or by distribution of an individual data flow in the network itself to several recipients in a defined group (multicasting). For each IPVS 600-..., a separate multicast address and the relevant port must be configured each per video link.

NoteThe requirement for multicasting operation is a network with multicasting capability using the UDP protocol and the IGMP protocol. Other group management protocols are not supported. The TCP protocol does not support multicast connections. The requirement for multicast operation in a network with multicasting capability is the set-up of a special IP address (class D address).

The network must support the set-up of a group IP address and the Internet Group Management Protocol (IGMP V3). The address area is 225.0.0.0 to 239.255.255.255.

The multicast address can be the same for several IPVS 600-... units. However, in this case it is necessary to use a different port in each case to ensure that several data streams are not transmitted simultaneously via the same port and the same multicast address.

The following settings must be performed separately in each IPVS 600-... .

Multicast address video 1For each IPVS 600-..., enter a multicast address which you wish to operate in the multicast mode (duplication of the data streams in the network). With the setting 0.0.0.0, the IPVS 600-... works in the multi-unicast mode (copying the data streams in the device). The IPVS 600-... supports multi-unicast connections for up to five recipients connected simultaneously. Duplication of the data in the device requires high computing power and can compromise image quality under certain circumstances.

Port:With simultaneous data streams to the same multicast address, the data streams must be assigned to different ports.Here, enter the relevant port address.

StreamingClick in the checkbox in order to activate multicast streaming operation for the relevant stream. Activation is not necessary for operation.

Multicast audio port 1Alongside video data, audio signals can also be transmitted and received. Audio transmission takes place in a separate data stream in parallel to the video data and so increases the network load. The audio data is encoded in accordance with G.711 and requires an additional bandwidth of appr. 80 kBit/s per direction.

If audio signals have to be transmitted in multicasting mode, these must be assigned to their own port as this is a separate data stream. Here, enter the relevant port address.

Audio signals are only transmitted if the audio settings and audio function are switched on in the configuration.

Multicast package TTLA value can be entered which determines how long the multicast data packages are active in the network. If multicasting is operated via a router, the value must be greater than 1.

32

Configuration of SIVS 600-...The configuration software DCIP CO 600-... is required for configuration of the SIVS 600-...Configuration takes place via a Windows PC. USB connection to the SIVS 600-... takes place via the PRI 602-... USB. With the configuration software, the call buttons are assigned to addresses. When configuring the PC user, these addresses are assigned to the Software Client. The addresses are designated in the software as IWA addresses and have 6 digits. Once programming for the SIVS 600-... has been completed, this is used to generate a file (*.dcip). This is then imported into every Software Client.

System requirementsfor the configuration software • PC with Intel Pentium III from 1 GHz or comparable processor• at least 256 MB RAM• min. 25 MB hard disk memory• Serial COM interface RS232 or serial USB adapter• CD-ROM drive for installation • VGA graphic card with at least 1024 x 768 pixel• Operating system Windows 2000/XP• Admin rights for installationAdditional memory capacity is required for:• Acrobat Reader 7• Microsoft Internet Explorer from version 4

Procedure for the configuration software• Installation of the configuration software•USB connection of the PC via PRI 602-... USB to the SIVS 600-...• Start the configuration software• Selection of whether DCIP 600-... or DCIP 740-... should be programmed• Project data can be optionally entered• Selection of the required speech connection, half-duplex or full-duplex• Input of the IP address of

6 Configuration softwareDCIP CO 600-...

33

the IPVS 600-.. for which the configuration is applicable. This input is required to ensure that the Software Clients are able to locate the DCIP in the network.• In the Inputs menu, all the IWA addresses are assigned. An IWA address for each call button/user. The addresses have 6 digits.• In the Inputs menu, the previously entered IWA addresses can be assigned to the call buttons at inputs E1-E4 if these are used.• Write the configuration to the SIVS with Send configuration. • In the menu File DCIP, generate the SC file for later import into the Software Client. (If required, users can be deselected which do not receive a call.)Note: This step is intended to create different configurations for different Software Clients (e.g. one workstation has access to doors for which another workstation is not authorized).

The configuration is saved as a file with the suffix *.dcip.

NoteAssign an unambiguous description to the *.dcip file (e.g. Secretarial.dcip).

Continue with step 3 on page 34.

34

6 Client-SoftwareDCIP SC 600-...

Installation of the Software ClientsThe Software Client DCIP SC 600-... must be installed on every PC you wish to receive door calls. The Software Client communicates with the calling station, the DCIP 600-... After installation, the file (*.dcip) generated using the configuration software must be imported.The addresses to which the client is intended to respond are selected from the imported file.

System requirementsfor the Software Client• Operating system Microsoft Windows 2000/XP• Pentium IV from 1.8 GHz or compatible CPUs• min. 256 MB RAM• Graphic card with at least 1024 x 768, 128 MB and 16 bit colour depth Graphic card and driver must be MPEG4 capable.• 100 Mbit Ethernet card• Sound card• Microsoft DirectX 9.0b or newer• Microsoft Internet Explorer from Version 4.0 to read the help

Procedure for installation• Install the DCIP SC 600 software• It may be necessary to install additional programs such as Microsoft Direct X Version 9.0b.• Start the Software Client• The Software Client configuration can be opened by pressing the right-hand mouse button on the virtual in-house telephone.• In the first tab Configuration, select add DCIP SC file and import the file exported by the configuration software (*.dcip).• It is then possible under DCIP SC-Edit file to assign an IWA address to the Software Client for the relevant DCIP 600-..., to which you wish the PC to respond.• Other IWA addresses can optionally be assigned to the Software Client 2. (e.g. for receiving an additional door call).

Licence regulationsFor each installation of the Software Client on a PC, a licence is required for the DCIP SC 600-0.The DCIP 600-0 includes four licenses, additional licenses must be ordered.

35

Possible error sources• No speech connection from the PC to the door. The microphone amplifier may not be activated.• Installation must take place as administrator, so that all registered users have access to the Software Client later.• Marked echo on the line in speech mode. In the Windows volume regulation for sound reproduction, Sound off must be activated under the microphone controller. This selection prevents the PC microphone signal being reproduced in the PC loudspeaker.• The other party is not audible at the PC.Possible causes: • No loudspeaker connected at the PC/monitor• No driver for the sound card• The loudspeaker is set to mute under the audio properties. (sound off)• If there is an active firewall, the application fileDCIP SC 600-0.exe must be defined as an exception or as a permanently authorized program/application.• In order to establish a video link, it may be necessary, for the drivers for the used graphic card to be updated to the latest status.

Other settings in the Software Client:

Free buttonsSelection of functions for buttons 1–3. Each button can be assigned an individual inscription text.

Call tonesSelection of call tones for door call and internal call. Alternatively, you can select your own *.wav files.Setting the volume for call tones

Speech volumeSetting the speech volume. Loudspeakers and microphones can be separately set. It may be necessary to carry out other settings in the control panel under “Sound”.

GeneralSelection of the Software Client language.“Start application automatically after logging onto the system?”

36

7 Setting the speech volumeLevel adjustment DCIP 600-...

Level adjustment IPVS 600-...Setting the volume of the PC user in the direction of the door station.

• At the back of the TLM/LL 611-..., set the potentiometer “Volume“ to the middle setting, “Boost” switch off (as-delivered status).• Establish a connection to a PC user.• At the PC, open the menu “Software Client configuration” and select the tab “Speech volume“.• Using the “Microphone“ controller, starting from 0% set the volume in the direction of the door so that when a person speaks loudly into the microphone of the receiver or headset, no distortion is audible at the door loudspeaker.As a rule, the optional field microphone amplifier remains switched on. This field can only be switched off in the case of microphones with a very high output level.• At the TLM/LL 611-... use the potentiometer “Loudspeaker“ or the boost function to set the optimum volume.

Level adjustment TLM/LL 611-... Setting the volume of the PC user from the door station in the direction of the PC user.

• At the back of the TLM/LL 611-..., set the “microphone“ potentiometer to the middle setting (as-delivered status).• Establish the connection to the PC.• At the PC, select Reproduction in the Speech volume menu.Ensure that “Tone off“ has been selected under the heading Microphone.• Using buttons + and –, set the optimum volume starting from 0%.• To ensure that the levels are stored, these must be performed via the configuration menu.

Level adjustment DCA 740-...Set the volume of the speech connection to the telephone system.

• At the back of the TLM/LL 611-..., set the potentiometer “Volume“ to the middle setting, “Boost” switch off (as-delivered status).• Establish the link to the TC system or public network telephone.• With potentiometer P1 in the DCA 740-01, set the optimum volume at the door.If applicable, regulate the “Loudspeaker“ potentiometer or use the boot function to achieve the required volume. • With potentiometer P2 in the DCA 740-0, set the optimum volume in the receiver.(Comparison: Normal volumes with public network calls).If applicable, regulate the “Microphone” potentiometer at the TLM/LL 611-..., in order to achieve the required volume.

38

8 DoorComDCA 740-01

The DoorCom Analog DCA 740-... is used as an interface between DoorCom IP and an analog telephone connection of a telecommunication system.

Up to 49 call destinations (addresses) can be assigned to the DCA 740-... . The functionality depends in the main on the capability of the telephone system / on the telephones connected to it.The assignment and functionality can be programmed in the SIVS 600-... The selection of users and control and switching functions takes place by means of DTMF dialling. The telecommunications system and the connected telephones must therefore possess DTMF dialling capability.

Functional characteristicsThe PBX extension of the telephone system must operate using the dual tone multiple-frequency (DTMF) dialling method. It is of no consequence whether the telephone system is an ISDN or analogue installation. After pressing the call button, the DCA 740-... dials the previously programmed call number; a telephone connected to the telephone system rings.After picking up the receiver, the active door call is superposed / signalled. By pressing a numerical button (0-9) at the telephone, it is possible to speak to the visitor (this function can be switched off). If the number #61 is pressed, the door release is actuated for 3 seconds. (For connection of more than one telephone, a so-called group call or collective call function must be set up in the telephone system. For details, ask the telephone system installer).

Power supplyThe DCA 740-... is supplied directly from the SIVS 600-... . A separate supply is consequently not required. The power to the a/b public network interface is supplied from the

9 DoorCom IPFactory setting IPVS 600-...

With the reset button at the IPVS 600-..., it can be reset to the as-delivered status. It is essential to load the Siedle factory configuration in the IPVS 600-... after a reset. Proceed as follows.1 Open the Internet Explorer.2 Access the video server (IPVS) with its IP address3 Access the following menus in sequence: SettingService parametersFirmware and configuration upload 4 Under Configuration upload, select the configuration file with „search...“ The file is on the supplied CD.5 Select the file with the rtc_image with upload. Using the Upload button, start the update.

telecommunication system or the a/b public network connection from the exchange. It is not possible to connect an individual public network telephone directly to the a/b line of the DCA 740.

Handling

DTMF dialling Function

0 - 9 door call

acceptance

#0 terminate

connection

#50 light

#61 door release

39

FAQWhy does the DCIP SC 600-0.exe software have to be enabled in the firewall?In order to permit a network connection of the software DCIP SC to the gateway (video server). The software independently establishes a network connection to the video servers. This entails bidirectional exchange of data.

Is door release also possible without Siedle Software ?No Exception: Via Visiomatic or via system partners such as Crestron, AMX ...with the DCIP -OEM

Must PCs have a fixed IP address? No. Only the IP address of the IPVS needs to be a fixed IP address. The IP address of the PC can (may) change. Exception: In case of a connection via cross cable e.g. when servicing.

Is it possible to record images? No

Is it possible to record speech? No

Which PC performance features are required? (For Windows 2000 only with the DCA 740-0)Personal Computer CPU Pentium IV 1.8 GHz- RAM 256 MB operating system Windows 2000, XP (SP2)- graphic card and driver with at least 1024x768, 128 MB memory and 16 Bit colour depth. (MPEG4-capable) Ethernet card 100 MBit sound card form DirectX 9.0b

Can several PCs be switched in parallel?Yes max. 25

Is it possible to reroute a line at the PC?No

Can a call forwarding command be placed at the PC?No

Is brokering possible at the PC?No

Are telephone calls stored? No

Is it possible to speak directly via IP telephones?No. (Only via the DCA 740-... and an a/b connection of the TC system)

Is SIP telephony possible? No

Troubleshooting PC software Client DCIP SC 600-0

After actuating the call button, no response occurs.Check terminal „G“ at the SIVS 600. Is this connected in accordance with the wiring diagram? If no external voltage is used, „G“ must be connected with „-“. Ensure that the input has been correctly configured.

The door call is signalled at the client PC, the video is not displayed. Enter the software „DCIP SC 600-0.exe“ in the Windows firewall as an exception. Update the graphic driver to the latest version. (This problem occurs primarily with laptops.) Check in the BIOS whether the memory assignment can be set for the graphics card. If so, set this to 32 MB. (this problem occurs primarily with laptops.) Set the hardware acceleration of the graphics card (display) to max.

Speech goes from the PC only in the direction of the door.Enter the software „DCIP SC 600-0.exe“ in the Windows firewall as an exception. Ensure that the configuration data has been transmitted via the configuration software to the SIVS 600-0.

Audio reception sounds distorted in the door loudspeaker. (like a robot‘s voice) Close the PC client and restart. This can occur during regeneration of the PC client, e.g. after a brief power

failure (storm).

When first accessing the PC client, the picture only appears after around 30 seconds. Load the current JAVA version. At least version 1.5 xxx- Ensure that the DNS server can always be reached. (If a DNS server is entered which is not reached, a number of time-outs run before the connection can be established).

Marked echo at the PC and at the door. In the sound card menu, go to the „Reproduction“ option (not the „Recording“ option) and set the microphone to „sound off“.

Troubleshooting PC configuration software DCIP CO 600-0After software start, a general error message appears.Experience value: Install the Net Framework 1.1 Version on your PC. (even if version 2.0 is already installed.)

Troubleshooting IPVS 600 The IPVS 600 cannot be addressed via the network. The IP address of the IPVS 600 does not agree with the network structure. In order to change the IP address of the IPVS 600-... , this must be connected via a cross cable to a PC (laptop). The laptop must now be adjusted to the IP address area of the IPVS 600. It must now be possible to address IPVS 600.

If the IPVS 600-0 is addressed via the browser, only a cross is displayed at the menu points. Is Java installed on the PC?At least version 1.5.xxx- Check the Java network settings. Set the button „Use browser network settings“ or enter the IP address of the IPVS 600 as an exception for which the proxy server should not be used.

10 DoorCom IP FAQand trouble shooting

40

10 ServiceMeasured values

Measurement values for DoorCom IP, to be measured using a digital multimeter

Idle status min. max.

Voltage +/- at line rectifier NG 600-... 24 V DC 28.5 V DC

Voltage c/b at line rectifier NG 600-... 12 V AC

Voltage b+/c- at SIVS 600-... 15 V DC

Voltage Da/Db at SIVS 600-... 0.3 V DC

Call status

Voltage E1-E4/G at SIVS 600-... 20 V DC 30 V DC

voltage USP/+ at SIVS 600-... 20 V DC 30 V DC

Sprechbetrieb

Speech mode Voltage +M/- at CMC 612-... 20 V DC 30 V DC

Voltage Mu/+M at TLM/LL 611-... and CMC 612-... 20 V DC 30 V DC

DCIP mit DCA 740-...

DCIP with DCA 740-...analogue PBX extension La/Lb 20 V DC 60 V DC

41

11 Glossary Index

AEM 645-... 9BTM 650-... 8CMC 612-... 9COM 611-... 9DCA 740-... 10, 36DCIP CO 600-... 11DCIP SC 600-... 11DRM 611-... 9IPVS 600-... 10, 14NG 600-... 10PRI 602-... 10SIVS 600-... 12, 14TLM/LL 611-0 12, 16TM 612-... 8TME 640-... 8TME 645-... 8

The current issue of the “ DoorCom IP “ system manual is available from the download area under www.siedle.de.

Technical additions and printing errors do not constitute grounds for any claims to damages.

Connection 18As-delivered status 38Block diagram 16Client 6, 34Commissioning 30Config 30Cross-over 30DoorCom 10Factory setting 38Full duplex 6HTTP 6IP 6IP address 6IWA 7LAN 7LED display 15Licences 11, 34Line rectifier 10Multicasting 7, 31Network cable 30Power supply 4, 10Programming 30Push to talk 7Reset 38RS232 7RS485 7Server 7Software Client 32Subnet mask 7System interface video server 10System requirements 32, 34System-free 4, 7TCP 7Terminals 16UDP 7Vario bus 7Web browser 7, 30Wiring diagram 18

© 2007/02.09Printed in GermanyOrder no. 0-1101/037154 EN

S. Siedle & Söhne

Postfach 1155D-78113 FurtwangenBregstraße 1D-78120 Furtwangen

Tel. +49 7723 63-0Fax+49 7723 [email protected]

manual doorcom ip dcip 600-0 - siedle · 2019. 2. 7. · dcip 600-0 4 group calculation max. number...

Documents