manual de servicio samsung awt24famea

ROOM AIR CONDITIONERAW0690AAW0790AAW07FASAAAW07FASBAAW07FASEAAW0890AAW09FASBAAW09FASEAAW09FBSEA

AW1090AAW10FAJAAAW10FAJBAAW12FAJAAAW12FAJBAAW12FAJDAAW12FAJEAAW12FBJEA

AW1290AAW14FAMBAAW18FAMBAAW18FAMCAAW18FAMBBAWT18FAMDAAW18FAMEAAW18FBMEAAW24FAMBBAW24FAMBAAW24FAMCAAWT24FAMEA

AIR CONDITIONER CONTENTS

1. Precautions

2. Product Specifications

3. Installation and Operating Instructions

4. Disassembly and Reassembly

5. Troubleshooting

6. Exploded Views and Parts List

7. Block Diagram

8. PCB Diagram

9. Wiring Diagram

10. Schematic Diagrams

SERVICE Manual

Co-DB68-02477A(1) 6/28/01 11:32 AM Page 2

1. Precautions

Samsung Electronics 1-1

1. Warning: Prior to repair, disconnect thepower cord from the circuit breaker.

2. Use proper parts: Use only exactreplacement parts. (Also, we recommendreplacing parts rather than repairing them.)

3. Use the proper tools: Use the proper toolsand test equipment, and know how to useequipment may cause problems later-intermittent contact, for example.

4. Power Cord: Prior to repair, check thepower cord and replace it if necessary.

5. Avoid using an extension cord, and avoidtapping into a power cord. This practicemay result in malfunction or fire.

6. After completing repairs and reassembly,check the insulation resistance.Procedure: Prior to applying power, measurethe resistance between the power cord and theground terminal. The resistance must begreater than 30 megohms.

7. Make sure that the grounds are adequate.

8. Make sure that the installation conditionsare satisfactory. Relocate the unit if necessary.

9. Keep children away from the unit while it isbeing repaired.

10. Be sure to clean the unit and its surroundingarea.

Fig. 1-1 Avoid Dangerous Contact

Fig. 1-2 No Tapping and No Extension Cords

Fig. 1-3 No Kids Nearby!

Fig. 1-4 Clean the Unit

1-DB68-02477A(1) 6/28/01 11:33 AM Page 1-1

1-2 Samsung Electronics

Type Model Name

A

B

C

: The symbol of model nameNotice

AW0690A

AW0790A

AW07FASAA

AW07FASBA

AW07FASEA

AW0890A

AW09FASBA

AW09FASEA

AW09FBSEA

AW1090A

AW10FAJAA

AW10FAJBA

AW12FAJAA

AW12FAJBA

AW12FAJDA

AW12FAJEA

AW12FBJEA

AW1290A

AW14FAMBA

AW18FAMBA

AW18FAMCA

AW18FAMBB

AWT18FAMDA

AW18FAMEA

AW18FBMEA

AW24FAMBB

AW24FAMBA

AW24FAMCA

AWT24FAMEA

1-DB68-02477A(1) 6/28/01 11:33 AM Page 1-2


2. Product Specifications

2-1 Table

Item Unit of Measure

Type

Dimensions:

(Width X Height X Depth)

Voltage

Phase

Frequency

Operating Current

Power Consumption

Refrigerant Type

Refrigerant Charge

Capacity

EER

Net Weight

Condenser

Condenser Fan

Evaporator

Evaporator Fan

Fan Motor

Compressor(Rotary)

Overload Protect

Compressor Capacitor

Fan Motor Capacitor

Fan Speed

Thermo Control

Off Timer

-

mm

Volt

-

Hz

A

W

FREON

g

BTU/h

BTU/h.W

kg

Row

Type

Row

Type

Model

Model

-

F / VAC

F / VAC

RPM

-

hr

5.6

600

380

6000

10

29

IC-9630SWD6F

44A062HS1EB

MRA12040-12008

30/370

4.5/440

810/750/690

520 x 345 x 485

6.8

715

350

7000

9.8

28

2 x 15

2 x 14

IC-9630SWD6C

44A072HW1EB

MRA98706-12008

25/370

6/450

800/750/700

WINDOW

115

SINGLE

60

R-22

Propeller Fan

Blower

Thermistor

24

7.4

815

380

8000

9.8

29

IC-9630SWD6E

44A080HU1EB

MRA12083-12008

35/370

6/450

910/810/750

9.2

1020

485

10000

10

45

2 x 17

AFS095ZREA

44B102HU1EF

MRA12109-12007

40/370

8/440

920/820/770

12

1300

610

12300

9.4

45

3 x 17

AFS100ZREB

44B124HU1EL

MRA98693-12008

45/370

15/450

920/850/780

600 x 394 x 595

2 x 14

660 x 425 x 730

11.7

1250

580

12500

10

50

2 x 19

2 x 15

OSME-708SWC

44B124HU1EL

MRA98693-12007

45/370

8/440

800/750/700

RemarksAW0690A AW0790AAW07FASAA AW0890AAW1090A

AW10FAJAA AW12FAJAA AW1290A

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-1


Table(cont.)


Type

Dimensions:


Voltage

Phase

Frequency

Operating Current

Power Consumption

Refrigerant Type

Refrigerant Charge

Capacity

EER

Net Weight

Condenser

Condenser Fan

Evaporator

Evaporator Fan

Fan Motor

Compressor(Rotary)

Overload Protect


Fan Motor Capacitor

Fan Speed Control

Thermo Control

Off Timer

-

mm

Volt

-

Hz

A

W

FREON

g

BTU/h

BTU/h.W

kg

Row

Type

Row

Type

Model

Model

-

F / VAC

F / VAC

RPM

-

hr

3.5

750

410

7000

9.3

2 x 15

IC-9630SWF6G

44A072IW1EB

MRA12043-12008

25/370

3/450

910/780/690

2 x 14

4.7

1000

420

9000

9

2 x 15

IC-9630SWF6G

44B092IW1EF

MRA12032-12008

20/370

3/450

910/780/690

5.2

1100

500

10000

9

43

2 x 17

AFS095ZTEA

44B102IU1EL

RAC12049-9622

20/450

2.5/450

800/720/650

6

1290

510

12000

9.3

45

2 x 17

AFS105ZUEA

44B124HU1EL

MRA12008-12008

30/450

3.5/450

900/840/780

520 x 345 x 485

29

600 x 394 x 595

WINDOW

220 (230-208)

SINGLE

60

R-22

Propeller Fan

Blower

Thermistor

24

6.5

1400

570

14000

10

53

2 x 19

2 x 15

OSME-906SWC

44B135IU1EL

RAC12074-9622

30/450

6/450

950/850/750

660 x 425 x 730

9.5

2000

1090

18000

9

61

3 x 16

3 x 15

AFS145ZUEA

48B175IV1EH

48B197IV1EH

MRA12107-12007

RAC12016-9622

35/450

40/450

6/450

1060/1010/970

12.5

11.5

2667

2500

1320

1280

24000

24000

8.8

8.2

71

3 x 16

4 x 15

3 x 15

AFS145ZUEA

48B220IV1EH

INTERNAL

MRA12068-12007

30/450

40/450

6/450

1060/1010/970

RemarksAW07FASBA AW09FASBA AW10FAJBA AW12FAJBA AW14FAMBA AW18FAMBAAW18FAMBBAW24FAMBAAW24FAMBB

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-2


Table(cont.)


Type

Dimensions:


Voltage

Phase

Frequency

Operating Current

Power Consumption

Refrigerant Type

Refrigerant Charge

Capacity

EER

Net Weight

Condenser

Condenser Fan

Evaporator

Evaporator Fan

Fan Motor

Compressor(Rotary)

Overload Protect


Fan Motor Capacitor

Fan Speed

Thermo Control

Off Timer

-

mm

Volt

-

Hz

A

W

FREON

g

BTU/h

BTU/h.W

kg

Row

Type

Row

Type

Model

Model

-

F / VAC

F / VAC

RPM

-

hr

8.5

1800

1090

18000

10

61

3 x 16

3 x 15

AFS145ZUEA

48B175IV1EH

MRA12107-12007

35/450

6/450

1060/1010/970

WINDOW

660 x 425 x 730

208-240

SINGLE

60

R-22

Propeller Fan

Blower

Thermistor

24

12.5

2695

1320

23700

8.8

71

3 x 16

4 x 15

AFS145ZUEA

EDB260211A

INTERNAL

30/450

6/450

1060/1010/970

RemarksAW18FAMCA AW24FAMCA

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-3


Table(cont.)


Type

Dimensions:


Voltage

Phase

Frequency

Operating Current

Power Consumption

Refrigerant Type

Refrigerant Charge

Capacity

EER

Net Weight

Condenser

Condenser Fan

Evaporator

Evaporator Fan

Fan Motor

Compressor(Rotary)

Overload Protect


Fan Motor Capacitor

Fan Speed

Thermo Control

Off Timer

-

mm

Volt

-

Hz

A

W

FREON

g

BTU/h

BTU/h.W

kg

Row

Type

Row

Type

Model

Model

-

F / VAC

F / VAC

RPM

-

hr

600 x 394 x 595

6.8

1330

660

12000

9.0

45

2 x 14

2 x 14

AFS105AUEA

48A124MV1EL

MRA98706-12008

30/450

4/450

890/840/780

WINDOW

200-220

SINGLE

50

R-22

Propeller Fan

Blower

Thermistor

24

660 x 425 x 730

10.5

2050

1480

18000

8.8

71

4 x 16

3 x 15

OSME-1206SWC

48B180MT1EH

MRA12108-12007

40/450

6/450

930/880/830

RemarksAW12FAJDA AWT18FAMDA

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-4


Table(cont.)


Type

Dimensions:


Voltage

Phase

Frequency

Operating Current

Power Consumption

Refrigerant Type

Refrigerant Charge

Capacity

EER

Net Weight

Condenser

Condenser Fan

Evaporator

Evaporator Fan

Fan Motor

Compressor(Rotary)

Overload Protect


Fan Motor Capacitor

Fan Speed

Thermo Control

Off Timer

-

mm

Volt

-

Hz

A

W

FREON

g

BTU/h

BTU/h.W

kg

Row

Type

Row

Type

Model

Model

-

F / VAC

F / VAC

RPM

-

hr

3.5

750

410

7000

9.3

28

44A070JW1EB

MST24AMN-12008

25/450

2.5/450

850/810/750

4.5

1000

390

9000

9.0

29

44B092JW1EF

MRA12056-12007

30/450

3/450

910/860/810

520 x 345 x 485

2 x 15

2 x 14

IC-9430SWJ5A

WINDOW

600 x 394 x 595

220-240

SINGLE

50

5.8

1330

R-22

660

12000

9.0

45

2 x 14

Propeller Fan

2 x 14

Blower

AFS105AUEA

48A124JV1EL

MRA12030-12008

30/450

3.5/450

890/840/780

Thermistor

24

9

2000

1160

18000

9.0

60

3 x 16

OSME-1404SAC

48B180JV1EH

MRA12016-12007

40/450

6/450

1060/1010/960

660 x 425 x 730

3 x 15

14

3000

980

24000

8.0

71

3 x 16

OSME-1256SWC

AWG5532EXC

INTERNAL

45/450

6/450

930/880/830

RemarksAW07FASEA AW09FASEAAW09FBSEAAW12FAJEAAW12FBJEA

AW18FAMEAAW18FBMEA AWT24FAMEA

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-5


2-2 Dimensions

2-2-1 Main Unit (Type A)

520

345

345

485

Front view Side view

(Unit : mm)

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-6


2-2-2 Main Unit (Type B)

600

394

394

595

(Unit : mm)

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-7


2-2-3 Main Unit (Type C)

2-2-3 Remote Control

660

425

425

695

Front view Side view

(Unit : mm)

Timer setting button

Sleep timer setting button

Operating modeselection buttons

Energy Saver button

Air flow blade swing button

Temperature adjustmentbuttons

Fan speedadjustment buttons

ON/OFF button

1-DB68-02477A(1) 6/28/01 11:33 AM Page 2-8


3. Installation and Operating Instructions

3-1 Installation

1. Make sure that you install the unit in an area thatprovides good ventilation. The air conditioner must not be blocked by anyobstacle affecting the air flow near the air inlet andair outlet.

2. Make sure that you install the unit in an area whichcan endure the weight and vibration of the unit.

3. Make sure that you install the unit away from heator vapor.

4. Make sure that you install the unit in an area wherethe cooled air can be evenly spread in a room.

5. Make sure that you install the unit in an area awayfrom TVs, audio units, cordless phones, fluorescentlighting fixtures and other electrical appliances.(obtain a clearance of at least one meter)

6. Make sure that you install the unit in an area whichprovides easy drainage for condensed water.

7. Make sure that you install the unit in an area notexposed to rain or direct sunlight.(Install a separate sunblind if exposed to direct sun-light.)

8. Do not install the unit in an area subjected to noiseor vibration amplification which may affect yourneighbor.(Fix the unit firmly if mounted in a high place.)

* When selecting the area for installing the unit, be sure to obtain approval of the customer.

Caution:

Do not use the air conditioner in such areas as a greasy area(including machine oil), saline area(sea side), or sulphuric area(hot spring). When using the air conditioner in these areas,special maintenance is required. Contact your local dealer or our service center for advice.

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-1


3-2 Function Description

3-2-1 Cooling operation mode

Fan speed indicator(LOW, MED, HIGH)

Temperature/Timer settings

Temperature adjustment buttons

Operating mode indicators(COOL, FAN)

Remote control sensorAir flow blade swing

ON/OFF button

Fan Speed adjustment button(LOW, MED, HIGH)

Air flow blade swing indicator

Energy saver indicator

ON/OFF Timer adjustment button

Sleep mode adjustment button

Timer indicator

Energy saver ON/OFF button

Operating mode selection button(COOLING, FAN)

Operating on/off

The compressor is turned on and off according to the ambient temperature and set temperature.1) Compressor on and off control

Compressor on and off control according to the ambient temperature

* The compressor is turned off when "ambient temperature = set temperature* The compressor is turned on when "ambient temperature = set temperature +1C"

2) Default value after power reset set temperature = 24C (75F)Fan speed = High

3) Set temperature indicating (setting) range : 1C(1F) interval from 18C to 30C. (64F to 86F)

3-2-2 Fan operation mode

1) If "Fan operation mode" signal is received from remocon or panel. the compressor is immediately turned off and only fan motor is operated at set blowing speed. it changes such as "High Med Low High"(if Fan speed is selected).

2) The initial Fan motor speed is set to "High".3) The set temperature can not be indicated and set.

3-2-3 Energy saver operation mode

* If the compressor turn off at the cooling operation, the fan motor turn off after operation during the fixation time only,and operation that energy saver by turn off the fixation time only, and operation that energy saver by turn off the motorcontinuously before the condition of the compressor on.

* The fan motor is not operated at flow wind operation.

* Energy saver operation specification at the cooling operation.1) Fan motor control in compressor on : operate with setting wind speed2) Fan motor control in compressor off : After compressor off, the fan motor is operated breeze for 2 minutes and then it

turn off.3) After the fan motor off, the compressor and fan motor is operated normally when the compressor on.

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-2


3-2-5 Sleep operation mode

1) Enable to sleep operation only when cooling operation.2) First, 7-SEG LED DISPLAY "SLEEP" while 15 second, Second, 7-SEG LED DISPLAY "8Hr"

And, automatically SET OFF after operated while 8 Hour3) If sleep operation, setting Temperature rise 1C after 1 Hour4) ON TIMER operation, not operation, ENERGY SAVER operation, not sleep operation.

3-2-4 Auto Restart (AWFBEA) : OPTION1) The operation mode, wind volume of fan motor and the set temperature right before the blackout are memorized in

EEPROM and so the operation can continue with the previous operation mode, wind volume of fan motor and the set temperature after the recover of blackout.

3-2-6 Air flow blade swing motor operation

1) The Air flow blade swing motor is turned on and off according to Air flow blade swing operation in remocon or panel, if SET is cooling or Fan operation mode.

2) If the operation mode is "ENERGY SAVER", in case of fan motor being turned off Air flow blade swing motor is immediately turned off.

3-2-7 LED display indication in case of error detection

ERROR OPERATION

ROOM THERMISTOR(OPEN or SHORT)

7-SEGLED DISPLAY

E1 displayed

1) Set operation in case of error occurrence. Malfunction of each temperature sensor (open, short)

- Error mode display, warning sound.- The operation status is off.

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-3

Key operational function

POWER Operation start and stop* First ON = operation start, second ON = operation stop

- Selected as "OFF > COOL or FAN". (DEFAULT=OFF)* Continuous operation is not available.

Mode Operation mode change* at every ON

- Selected as "COOL > FAN". (Default=COOL)* If operation is OFF, it is considered as an invalid key.* Continuous operation is not available.

Fan speed Fan motor speed setting* at every ON

- Selected as HIGH > MED > LOW > HIGH. (DEFAULT=HIGH)

Temperature Currently displayed set temperature increase/decrease(, ) * At every pressing, the set temperature is changed by 1C, (1F)

(increase() : 18C > 19C > ... > 29C > 30C), (64F -> 65F -> ... -> 85F -> 86F)(decrease() : 24C > 23C > ... > 17C > 18C), (86F ->84F -> ... -> 65F -> 64F)

* In case of the set temperature of 30C(86F), when the increase key is pressed temperature does not increase any more.

* In case of the set temperature of 18C(64F), when the decrease key is pressed temperature does not decrease any more.

* In case of above situation, when increase/decrease key is pressed by remocon, warning sound is generated.

* If operation is OFF, it is considered as an invalid key.* In case of FAN mode operation, it is considered as an invalid key.* Continuous operation is available.

Air Swing Circulaire motor operation and stop* Once ON=Circulaire motor operation. Another ON-Circulaire motor stop.* Continuous operation is not available.* In case of operation stop, when the fan motor is turned off it is considered as an invalid key.

Timer Setting the on/off timer(ON/OFF) * Can set OFF TIMER HOUR if set is operation

* Can set ON TIMER HOUR if set is not operation* Once ON=standby setting TIMER : displayed* In case of key pressing in status of standby setting ON/OFF TIMER

(Hr > 1Hr > 2Hr > ... > 23Hr > 24Hr)* If press TIMER key countinuosly operate such the lower part

(Hr > 1Hr > 2Hr > ... > 24Hr > --Hr)* Continuous operation is available.

Sleep SLEEP mode on and off* Once ON=SLEEP mode on, Another ON=SLEEP mode off

Continuous operation is not abailable Operation off, on timer Operation, save operation , not key operation

* Not SLEEP operation is FAN mode

Energy Saver Power save mode on and off* Once ON=Power save mode on, Another ON=Power save mode off* Continuous operation is not available.* If operation is OFF, it is considered as an invalid key.

3-2-8 Panel key operation

Key discriptionKey name


1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-4

3-2-9 LED lamp operation specifications

LAMP name Operations specifications

COOLING ( ) The mode is set to "COOL" > ONOthers > OFF

FAN ( ) The mode is set to "FAN" > ONOthers > OFF

HIGH ( ) The mode is set to "HIGH" > ONOthers > OFF

MED ( ) The mode is set to "MED" > ONOthers > OFF

LOW ( ) The fan speed is set to "LOW" > ONOthers > OFF

TIMER ( ) The mode is set to "TIMER" > ONOthers > OFF

ENERGY SAVER ( ) The mode is set to "ENERGY SAVER" > ONOthers > OFF

AIR SWING ( ) The mode is set to "Air Swing" > ONOthers > OFF

In case of set temperature display-> NO. (1) 7SEG LED DISPLAY indicates temperature of the tens digit-> NO. (2) 7-SEG LED DISPLAY indicates temperature of the units digitIn case of time display-> NO. (1) 7SEG LED DISPLAY indicates time of the tens digit -> NO. (2) 7SEG LED DISPLAY indicates time of the units digit

In case of set temperature display-> NO. (3) 7SEG LED DISPLAY indicates temperature unit()-> NO. (4) 7-SEG LED DISPLAY indicates temperature unit(C), (F)In case of time display-> NO. (3) 7SEG LED DISPLAY indicates time unit(H) of the tens digit -> NO. (4) 7SEG LED DISPLAY indicates time unit(r) of the units digit

First, 7SEG LED DISPLAY "SLEEP" while 15 second, Second, 7-SEG LED DISPLAY "8Hr"

(1) (2)

(3)

(1) (2) (3) (4)

(4)


1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-5


3-3 Remocon Control

3-3-1 Remocon key operation

11) In case of pressing POWER key, operation start and stop.12) In case of pressing COOL key, cool mode operation start.13) In case of pressing FAN key, fan mode operation start.14) In case of pressing HIGH key, fan motor operates high speed.15) In case of pressing MED key, fan motor operates mid speed.16) In case of pressing LOW key, fan motor operates low speed.17) In case of pressing ENERGY SAVER on/off key, set operates as power saving mode.18) In case of pressing key, set temperature increase by 1C(18C ~ 30C), 1F(64F ~ 86F).19) In case of pressing key, set temperature decrease by 1C(30C ~ 18C), 1F(86F ~ 64F).10) In case of pressing TIMER key, the convenient reserve TIMER time increase by 1 Hr (1Hr ~ 24Hr).11) In case of pressing SLEEP key, SLEEP operates.12) In case of power off, all keys except POWER key are considered as an invalid key.

Timer setting button

Sleep timer setting button

Operating modeselection buttons

Energy Saver button

Air flow blade swing button

Temperature adjustmentbuttons

Fan speedadjustment buttons

ON/OFF button

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-6


3-3-2 Resistor values table of ROOM THERMISTOR for each temperature

Temperature[C]

THERMISTOR RESISTOR[Kohm] 1%

7069686766656463626160

59585756555453525150

49484746454443424140

39383736353433323130

2.2292.2962.3652.4372.5122.5892.6692.7522.8382.9283.021

3.1163.2163.3193.4263.5373.6523.7723.8974.0264.161

4.3004.4444.5944.7494.9125.0805.2565.4395.6305.828

6.0336.2466.4686.6996.9417.1927.4557.7298.0158.313

Temperature[C]

THERMISTOR RESISTOR[Kohm] 1%

29282726252423222120

19181716151413121110

9876543210

-1-2-3-4-5-6-7-8-9

8.6228.9449.2819.63210.00010.38010.78011.20011.63012.090

12.56013.06013.57014.12014.68015.28015.90016.55017.24017.960

18.70019.48020.29021.15022.05022.99023.90025.03026.13027.280

28.47029.72031.04032.43033.89035.43037.05038.76040.560

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-7


4. Disassembly and Reassembly

4-1 Compressor Replacement Flow Chart

Locate cause of defect

Release refrigerant

Disconnect electrical wiringfrom compressor

Cut refrigerant lines from compressor

Plug disconnected lines

Replace compressor

Inspect electrical wiring for defects, and terminals forcorrect and secure connections

Solder discharge line

Corrective actionCheck refrigerant oil level

Add oil as necessary

Solder suction line Use nitrogen gas

Perform soldering function

Fill system with nitrogen gas

Check for leakage

Pinch and braze filling tube

Recharge system

Evacuate system

Release nitrogen gas?

Problem?

Low oil level? NY

Y

N

N

YLeakage?

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-8

4-2 Disassembly and Reassembly Procedure

Stop operating the air conditioner, and pull out the power cord before repair.

No. Part name Procedures Remarks

!

@

#

Ass'y Grill

Ass'y Cabinet

Ass'y Control

1. Pull the panel front and remove the screwon the grille.

2. Hold the lower part of grill with two handswhile pressing down on both sides of thelower part of the cabinet, pull it forward byabout 30, and the then lift it up for removal.

1. Remove the two screws both side cabinet.

2. Pull the front both side, and remove the unitfrom the cabinet.

1. Remove the blade V and arm blade.

2. Remove 2 screws, and 2 earth wire screws.

3. Remove two lead wire assemblies.

4. Take out the control box forward.

!!

4-2-1 Type A


*The type of front-paneldepends on models.

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-9



$

%

Frame Up

Case Cond & Propeller Fan

1. Remove 6 screws on the Frame upand remove the Frame up and the reinffrom case cond.

1. Remove two screws on the bottom side,and 4 screws on the case cond.

2. Pull up the case cond and separate thecond case from the cond.

3. Remove the nut flange, and remove thepropeller fan

Disassembly and Reassembly

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-10



^

&

Cond Casing

Blower & Motor

1. Remove the cond casing

1. Move the motor & blower toward theevap, and lift up the motor & blower fromthe frame low.


1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-11




!

@

#

Ass'y Grill

Ass'y Cabinet

Ass'y Control



1. Remove the screws on both sides of the cabinet to disconnect the cabinet and frame.

2. Pull the handle on the front side of thebottom, and remove the unit from thecabinet.

1. Remove 6 screws, and earth wire screw.

2. Remove three lead wire assemblies.

3. Remove the blade V and arm blade.


4-2-2 Type B



1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-12



$

%

Frame Up

Case Cond & Propeller Fan

1. Remove 10 screws on the Frame Up.

1. Remove two screws on the bottom side, and 5 screws on the case cond.

2. Remove the nut flange, and remove the propellr fan


1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-13



Blower & Motor

Cond Casing

1. Remove two screws on the clip motor,and remove the clip motor.

2. Move the motor & blower toward theevap, and lift up the motor & blowerfrom the frame low.

1. Remove the cond casing


1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-14



4-2-3 Type C



!

@

#

Ass'y Grille

Ass'y Cabinet

Ass'y Control



1. Remove the screws on both sides of thecabinet to disconnect the cabinet and frame.

2. Pull the handle on the front side of thebottom, and remove the unit from thecabinet.

1. Remove 10 screws, on the evap cover andearth wire screw.


1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-15




$

%

Assy - Evaporator

Plate - Evap Casing

2. Remove 3 screw on the control box andtwo lead wire assemblies.


1. Remove for screws on the left and rightside of the evaporator.

1. Lift up the evaporator, and remove the traydrain.

2. Remove two screws on the left side of theplate evap casing.

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-16




^

&

*

Blower

Propeller Fan

Motor Supporte &Motor

1. Loosen the hexagon nut, and removethe blower.

1. Remove two screws on the bottomside, and 5 screws on the case cond.

2. Loosen the hexagon nut, and removethe fan

1. Remove four hexagon nuts on the basepan.

2. Move the motor - assembly toward thecondenser, and lift up the motor -assembly from the frame.

3. Remove the clips on both sides carefullyusing the (-) driver.

1-DB68-02477A(1) 6/28/01 11:33 AM Page 3-17


MEMO

1-DB68-02477A(1) 6/28/01 11:34 AM Page 3-18


5. Troubleshooting

5-1 Basic Checkpoints for Troubleshooting

Check the basic checkpoints first to determine whether it is machine trouble or a problem in theoperation method. When it is not related to the basic checkpoints, perform checking in accordancewith the procedures of troubleshooting by symptom.

1) Is the voltage of the power source appropriate ?(1) It should be within the rating voltage 10% range. (2) The air conditioner may not operate properly when the voltage is out of this range.

2) Is the connection with the fan motor, compressor wire, and starting condenser appropriately made ?

3) The symptoms listed in the table below are not indicative of machine trouble.

Symptom Cause and check

No operation Check whether there is power failure or the power plug is pulled out. Check whether the unit is stopped as a result of completion

of the sleep time. Pull out the power plug for ten seconds, and then insert it again.

Air flows, but Check whether the Air filter is clogged with dust or is dirty.no cooling Check whether the desired temperature is too high. Set the desired

temperature to a lower level than the current temperature. Check whether it is in "FAN" mode.

The remocon does Check whether battery is completely depleted.not operate Check whether the battery is properly inserted.

Check whether the receiving window of the remocon for the assembly main PCB is blinded.

Check whether the remocon is affected by jamming due to a neon sign.

No temperature Check whether the unit is in "FAN" mode.setting (In "FAN" mode, only the current temperature is displayed, and the

desired temperature is not set.)

Checking and Display of Fault Area

ERROR OPERATION

ROOM THERMISTOR (OPEN OR SHORT)

ERROR OPERATION

E1 displayed

2-DB68-02477A(1) 6/28/01 11:34 AM Page 5-1


5-2 Troubleshooting by Symptom

5-2-1 No power

1) Check points

(1) Is the voltage of the power source normal ? (the rating voltage 10% range.) (2) Is the electric wire in good contact ?(CN 71, RY 71)(3) Is the output voltage of the IC01(KA 7812) normal ?(DC 11.5V ~ DC 12.5V)(4) Is the output voltage of the IC02(KA 7805) normal ?(DC 4.5V ~ DC 5.5V)

Turn off the power, and then turn it on again fiveseconds later.

Replace the assembly main PCB.

Dose the buzzer sound, when the power on?

Check whether the "COOLING ICON" LED lamp is on,and the operation starts when pressing the ON/OFFbutton of the remocon.

Is the primary voltage of the transformer normal?(the rating voltage 10% range.)

Is the secondary voltage of the transformer normal?(AC 13V ~ AC 17V)

Is the F701(3.15A) fuse blown?

Is the rectifier diode(D101~D104) normal?

Are the IC01(KA7812) and IC02(KA7805) normal?

- Is the voltage of DC 17V ~ DC 23V applied at both ends of the C101 electrolytic condenser?

- Is the voltage of DC 12V applied at both ends of the C102 electrolytic condenser?

- Is the voltage of DC 5V applied at both ends ofthe C103 electrolytic condenser?

Normal operation.

Normal operation.

Replace the fuse.

Check the power cord and electric wire.

Check and replace the trans.

Check the D101 ~ D104 for cold soldering. Replace the rectifier diode

Check both ends of the C101 for short and cold soldering.

Check the +12V for a short. Check the +5V for a short. Check and replace the C101~104.

Check the IC01, and IC02 for cold soldering and a short.

Replace the IC01, and IC02.

N

N

N

Y

Y

Y

Y

Y

N

N

N

N

N

Y

Y

Y

2-DB68-02477A(1) 6/28/01 11:34 AM Page 5-2


5-2-2 When the MEMBRANE KEY PAD AND LED DISPLAY

1) Check points

(1) Is the voltage of the power source normal ? (the rating voltage 10% range.)(2) Is the electric wire in good contact ?(CN71, RY71)(3) Is the connection of the assembly main PCB, and MEMBRANE KEY PAD in good contact?

(CN91)

Check the micom(IC04) for a short,and replace it.


Check the Q901~Q905 for a short, and replace it.


Normal operation


Replace the MEMBRANE KEY PAD

Replace the MEMBRANEKEY PAD.

Y

N

Normal operationN N

N

N N

N

Y

Y Y

Y Y

Y

Y

Turn off the power, and then turn it on againfive seconds later.

When the LED DISPLAY isnot operated.

When the MEMBRANE KEYis not operated.

Is the voltage of the micom(IC04) No.1, 2, 38~43 port asquare wave?

Is the voltage of themicom (IC04) No.13, 14 port a square wave?

Is the voltage of the micom(IC04) No.3, 4, 10, 11, 44 port a square wave?

Is the voltage of the micom(IC04) No.3, 4, 10, 11, 44 port asquare wave?

Is the voltage of theQ901 ~ Q905 square wave?

Check the IC07for a short, andreplace it.

N Is the voltage of theIC07 No. 10~16 a square value?

2-DB68-02477A(1) 6/28/01 11:34 AM Page 5-3


5-2-3 When the remocon is not operated

1) Check points

(1) Is the voltage of the power source normal ? (the rating voltage 10% range. )(2) Is the electric wire in good contact ? (CN71, RY71)(3) Is the assembly main PCB in good contact with the MEMBRANE KEY PAD(CN91)(4) Is the battery voltage of the remocon above DC 2.7V?

Turn off the power, and then turn it onagain five seconds later.

Replace the assembly main PCB.

Dose the Buzzer sound, when the power on?

Check whether the "COOLING ICON" LED lamp is onand th operation starts when pressing theon/off button of the remocon.

Is the battery voltage of the remocon above DC 2.7V?

Is the collector voltage of the remocon QT1, QT2a square wave?

Does the X-TAL(RJ 455JB) oscillate normally?

Is the input voltage of the micom(IC04) No. 15pin of the assembly main PCB a aquare wave?

Go to the clause "No power".

The remocon is normally operated.

Replace the battery.

Check the X-TAL for cold soldering and ashort.

Replace relevant components.

Check the micom(ICT1) QT1, and QT2 for cold soldering and a short.

Replace relevant components.

Check the R415 components. Check the assembly main PCB micom(IC04).

N

Y

N

Y

Y

Y

Y

N

N

N

N

Y

2-DB68-02477A(1) 6/28/01 11:34 AM Page 5-4


5-2-4 When the compressor is not operated

1) Check points

(1) Is the voltage of the power source normal ? (the rating voltage 10% range. )(2) Is the desired temperature lower than the indoor temperature in the COOL mode?

(Compressor stopped)(3) Is the starting condenser in good contact?(4) Is the electric wire in good contact ? (CN71, RY71)(5) Is the output voltage of the IC01(KA7812) and IC02(KA7805) normal ?


Replace the compressor.

Dose the Buzzer sound, when the power on?

Check whether the "COOLING ICON" LED lamp is onand the operation starts when pressing the on/off button of the remocon.

Is the IC03 output normal?- When the compressor is ON, IC03

No. 15 pin > Low.

Does the relay(RY71) operate normally?- When the compressor is ON, the RY71 should operate.

Is the compressor normal?


Go to the clause "when he remocon does not operate".

Check the IC03 for short and cold soldering. Replace the IC03.

Check the relay coil resistance.(resistance : About 15020)

Replace the relay.

Check the operation of the O.L.P,and replace it if necessary.

Check the compressorresistance.(0 : short, : open)

N

Y

Y

Y

Y

Y

N

Normal operation.

N

Y

N

N

N

Check whether the compressor is activated in three minutes after turning on the power with the "COOLINGICON" LED lamp being switched on when selecting thecool mode of the remocon.

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-5


5-2-5 When the air swing motor is not operated

1) Check points

(1) Is the voltage of the power source normal ? (the rating voltage 10% range. )(2) Is the electric wire in good contact ?(CN71, RY71)(3) Is the swing motor connector in good contact?(CN71)(4) Is the terminal connected to the swing motor in good contact?(5) Is the output voltage of the IC01(KA7812) and IC02(KA7805) normal?


Replace the air-swing motor.


Does the air-swing motor operate whenpressing the air-swing button of the remote control?

Is the IC03 output normal?- When the air-swing motor is on, IC03

No. 11 pin Low

Does the relay(RY 75) operate normally?- When the air-swing motor is operated, the

RY75 should be operated.


Normal operation.

Check the IC03 for a short and cold soldering.

Replace the IC03.

Check the relay coil resistance.(Normal: About 400)

Replace the relay.

Check the air-swing motor resistance.(0 : short, : open)

N

Y

N

Y

Y

Is the air-swing motor normal?

Y

Y

N

Check whether the COOLING ICON LED lamp is on,and the operation starts when pressing the ON/OFFbutton of the remocon?

Go to the clause of when the remocondose not operated

Y

N

N

N

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-6


5-2-6 When the fan motor does not operated

1) Check points

(1) Is the voltage of the power source normal ? (the rating voltage 10% range. )(2) Is the electric wire in good contact ?(CN71, RY71)(3) Is the starting condenser(FAN MOTOR) in good contact?(4) Is the fan motor connector in good contact?(CN73)(5) Is the output voltage of the IC01(KA7812) and IC02(KA7805) normal ?

Turn off the power, and then turn it on again five seconds later.

Replace the fan motor.


Check whether the "COOLING ICON" LED lamp is on andthe operation starts when pressing the on/off button of the remocon.

Is the IC03 output normal?- When the fan motor is High, IC03 No. 13 pin > LOW. - When the fan motor is Med, IC03 NO. 14 pin > LOW.- When the fan motor is Low, IC03 No. 16 pin > LOW.

Does the relay(RY 72, 73) operate normally?- When the fan motor is High, RY72 should operate.- When the fan motor is Med, RY73 should operate.- When the fan motor is Low, RY76 should operate.


Go to the clause of "when the remocondoes not operated".

Check the IC03 for a short and cold soldering.

Replace the IC03.

Check the relay coil resistance.(Normal: About 400)

Replace the relay.

N

Y

Y

Y

Is the fan motor normal?

Y

Y

N

N

N

Check the fan motor resistance.(0 : short, : open)

Check the fan motor thermal fuse?(130C)

N

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-7


6. Exploded View and Parts List

6-1 Main unit (Type A)

13

15

14

17

16

2322 24

18

2021

19

1

2-1

2-33

2

4

2-2

6

5

89

12

10

11

7

25

27

26

28

29

34

35

30-

11

30-

12

30-

10

30-

930

-8

30-

730

-1

30

-4 30

-3

30-

530

-6

3130

30-

2

33

2-DB68-02477A(1) 7/2/01 10:07 AM Page 5-8


Part List (Type A)

No DescripitionCode No. SpecificationQty

AW0690A AW0790A AW07FASAA AW07FASBA AW07FASEA AW0890A AW09FASBA AW09FASEA AW09FBSEA

1 DB64-10158A GRILLE-AIR INLET HIPS,2mm 1 1 - - - 1 - - -DB64-00104A GRILLE-AIR INLET HIPS,2mm - - 1 - 1 - 1 1 1DB64-00104B GRILLE-AIR INLET HIPS,2mm - - - 1 - - - - -

2 DB92-70096D ASS'Y PANEL- FRONT ASSY 1 1 - - - 1 - - -DB92-00052A ASS'Y PANEL- FRONT ASSY - - 1 - 1 - 1 1 1DB92-00052B ASS'Y PANEL- FRONT ASSY - - - 1 - - - - -

2-1 DB63-30158A FILTER-GUARD HIPS,2mm 1 1 - - - 1 - - -DB74-00005C FILTER-GUARD ZENO BLUE - - 1 1 1 - 1 1 1

2-2 DB64-70093A PANEL-FRONT HIPS,2mm 1 1 - - - 1 - - -DB64-00167A PANEL-FRONT HIPS,2mm - - 1 - 1 - 1 1 1DB64-00167B PANEL-FRONT HIPS,2mm - - - 1 - - - - -

2-3 DB66-30191A BLADE-H HIPS 1 1 - - - 1 - - -DB66-00053A BLADE-H HIPS - - 1 - 1 - 1 1 1DB66-00053B BLADE-H HIPS - - - 1 - - - - -

3 DB96-00045C ASSY-EVAP 2R*14S 1 1 1 - - 1 - - -DB75-00001B ASSY-EVAP 2R*14S - - - 1 1 - - - -DB96-00045B ASSY-EVAP 3R*14S - - - - - - 1 - -DB96-00045A ASSY-EVAP 2R*14S - - - - - - - 1 1

4 DB90-00002D ASSY FRAME-LOWER AW07A1SB,- 1 1 1 1 1 1 1 1 15 DB66-30211B BLADE-V PP,SC-97525R 1 1 1 1 1 1 1 1 16 DB66-70030A LEVER-DAMPER HIPS,SC-94445R 1 1 1 - 1 1 1 1 1

DB66-70030C LEVER-DAMPER HIPS,W9391 - - - 1 - - - - -7 DB67-50078A BLOWER ABS 1 1 1 1 1 1 1 1 18 DB31-00073A MOTOR FAN IC-9630SWD6F 1 - - - - - - - -

DB31-00073E MOTOR FAN IC-9630SWD6C - 1 - - - - - - -DB31-00004P MOTOR FAN IC-9630SWD6E - - 1 - - - - - -DB31-00073C MOTOR FAN IC-9430SWJ5A - - - - 1 - - 1 1DB31-00073B MOTOR FAN IC-9630SWD6E - - - - - 1 - - -DB31-00073D MOTOR FAN IC-9630SWD6G - - - 1 - - 1 - -

9 DB67-50077A FAN-PROPELLER ABS 1 1 1 1 1 1 1 1 110 DB90-00013B ASSY-CASE-COND ASSY 1 1 1 1 1 1 1 1 111 DB90-00014G ASSY FRAME-UPPER ASSY 1 1 - 1 1 1 1 1 1

DB90-00014H ASSY FRAME-UPPER ASSY - - 1 - - - - - -12 DB61-00027B FRAME-REINF PP,GRAY 1 1 1 1 1 1 1 1 113 DB75-00002A CONDENSER 2R,15S,GROOVE 1 1 - 1 - - - 1 1

DB75-00002B CONDENSER 2R,15S,GROOVE - - 1 - 1 - 1 - -DB75-00011B CONDENSER 2R,15SGROOVED - - - - - 1 - - -

14 DB63-10388A CAP EPDM,BLK - - 1 1 1 - 1 1 115 DB90-20212F ASSY-BASE SGCC-M,SC94445T 1 1 - - - 1 - - -

DB90-20212B ASSY-BASE SGCC-M,SC94445T - - 1 1 1 - 1 1 116 DB96-00260A ASSY-TUBE CAPILLARY 1.3*1100 1 - - - - - - - -

DB62-00372A ASSY-TUBE CAPILLARY C1220T-H - 1 1 - - - - - -DB96-00077A ASSY-TUBE CAPILLARY AW0719 - - - 1 1 - - - -DB96-00552A ASSY-TUBE CAPILLARY 1.42xL1200 - - - - - 1 - - -DB96-00046A ASSY-TUBE CAPILLARY AW09A2SB - - - - - - 1 - -DB96-00077B ASSY-TUBE CAPILLARY AW09G2SE - - - - - - - 1 1

17 DB96-00008B ASSY TUBE SUCTION AW07A2SB 1 1 - 1 1 1 - - -DB62-00370A ASSY TUBE SUCTION C1220T-0,MEI-COMP - - 1 - - - - - -DB96-10736A ASSY TUBE SUCTION AW09B0SB - - - - - - 1 - -DB96-10736B ASSY TUBE SUCTION AW09G2SE - - - - - - - 1 1

18 DB62-00150C TUBE DISCHARGE C1220T-0,D7.94,T0.7 1 1 - 1 1 - - - -DB62-00391A TUBE DISCHARGE C1220T-O,OD7.93,T0.7 - - 1 - - - - - -DB62-00483A TUBE DISCHARGE C1220T-O,OD7.93,T0.7 - - - - - 1 - - -DB62-00152A TUBE DISCHARGE C1220T-0,D7.94,T0.7 - - - - - - 1 1 -DB62-00440A TUBE DISCHARGE C1220T-0,D7.94,T0.7 - - - - - - - - 1

19 44A062HS1EB COMPRESSOR 115V,60Hz,R22,1Ph 1 - - - - - - - -44A072HW1EB COMPRESSOR 1Ph,115V,R22,60Hz - 1 - - - - - - -DB95-00113E COMPRESSOR 2R11S3R126-6,MATSUSHTA - - 1 - - - - - -44A072IW1EB COMPRESSOR 208-230V,60Hz,1Ph,R-22 - - 1 - - - - -44A070JW1EB COMPRESSOR 220-240V,50Hz,1Ph,R-22 - - - - 1 - - - -44A080HU1EB COMPRESSOR 115V,60HZ,1PH,8.0K - - - - - 1 - - -44B092IW1EF COMPRESSOR 208-239V,60Hz,1Ph,R-22 - - - - - - 1 - -44B092JW1EF COMPRESSOR 1Ph,50Hz,R22,220-240V - - - - - - - 1 1

20 DB60-30028A NUT-WASHER HEX,2C,M8,ZPC 1 1 1 1 1 1 1 1 121 DB73-00070A GROMMET-ISOLATOR NR 35 1 1 1 1 1 1 1 1 122 DB63-10026A COVER-TERMINAL NORYL,SEI-701 1 1 - 1 1 1 1 1 1

2-DB68-02477A(1) 7/2/01 10:07 AM Page 5-9


Part List (Type A) (cont.)


AW0690A AW0790A AW07FASAA AW07FASBA AW07FASEA AW0890A AW09FASBA AW09FASEA AW09FBSEA

22 DB63-00023A COVER-TERMINAL ME1 - - 1 - - - - - -23 DB60-30018A NUT-FLANGE PI0.8,M5,SM20C 1 1 1 1 1 1 1 1 124 DB47-20002F OLP MRA12040-12008 1 - - - - - - - -

DB47-20001V OLP MRA98706-12008 - 1 - - - - - - -DB35-00012B OLP MRA98705 - - 1 - - - - - -DB47-20002J OLP MRA 12043-12008 - - 1 - - - - -DB47-20001Y OLP MST24AMN-12008 - - - - 1 - - - -DB47-20066B OLP 150/69,31.0 - - - - - 1 - - -DB47-20002A OLP MRA12032-12008 - - - - - - 1 - -DB47-20002U OLP MRA12056-12007 - - - - - - - 1 1

25 DB64-00135H CABINET SGCC-M 1 1 - - - 1 - - -DB64-00135A CABINET SECC-P,SC-94445T - - 1 1 1 - 1 1 1

26 DB64-00048B SHUTTER-ANGLE UP HIPS,T3.0,520 1 1 - - - 1 - - -27 DB92-00113A ASSY SHUTTER-LF ASSY 1 1 - - - 1 - - -28 DB92-00112A ASSY SHUTTER-RH ASSY 1 1 - - - 1 - - -29 DB61-30219F BRACKET-INSTALL SGCC-A,T1.6 1 1 - - - 1 - - -30 DB93-00465K ASSY CONTROL-E ASSY 1 - - - - - - - -

DB93-00465Q ASSY CONTROL-E ASSY - 1 - - - - - - -DB93-00705A ASSY CONTROL-E ASSY - - 1 - - - - - -DB93-00465L ASSY CONTROL-E(TAIWAN) ASSY - - 1 - - - - - -DB93-00465M ASSY CONTROL-E(TAIWAN) ASSY - - 1 - - - - -DB93-00465D ASSY CONTROL-E ASSY - - - - 1 - - - -DB93-00465H ASSY CONTROL-E ASSY - - - - - 1 - - -DB93-00465G ASSY CONTROL-E ASSY - - - - - - 1 - -DB93-00465C ASSY CONTROL-E ASSY - - - - - - - 1 -DB93-00465P ASSY CONTROL-E ASSY - - - - - - - - 1

31 DB93-00284K ASSY REMOCON ASSY 1 1 1 1 1 1 1 1 133 DB97-30156C ASSY ACCESSORY ASSY 1 1 - - - 1 - - -34 DB60-30002A NUT-FLANGE M6 1 1 1 1 1 1 1 1 135 DB60-30004A NUT FLANGE M6,SM20C 1 1 1 1 1 1 1 1 1

2-DB68-02477A(1) 7/2/01 10:07 AM Page 5-10


6-2 Main unit (Type B)

6

7

3

15

21

13

4

9

8

10

11

12

1716

20

18

19

14

5

22

2-1

2-2

2-3

1

24

23

2

25

25-

5 25-

11

25-

10

25-

7

25-

6

25-

8

25-

1

25-

2

25-

3

25-

4

25-

9

25-

13

25-

12

28

27

26

2-DB68-02477A(1) 7/2/01 10:07 AM Page 5-11


Part List (Type B)

No Descripition Code No. SpecificationQty

AW1090A AW10FAJAA AW10FAJBA AW12FAJAA AW12FAJBA AW12FAJDA AW12FAJEA AW12FBJEA

1 GRILLE-AIR INLET DB64-10145A HIPS,T2.5 1 - - - - - - -GRILLE-AIR INLET DB64-00101A HIPS,T2.5 - 1 1 1 1 1 1 1

2 ASSY PANEL-FRONT DB92-00133A ASS'Y SC-94445R 1 - - - - - - -ASSY PANEL-FRONT DB92-00072A ASS'Y SC-94445R - 1 1 1 1 1 1 1

2-1 PANEL-FRONT DB64-70080A HIPS 1 - - - - - - -PANEL-FRONT DB64-00168A HIPS,T2.5 - 1 1 1 1 1 1 1

2-2 GUARD AIR-FILTER DB63-30142A HIPS,T2 1 - - - - - - -GUARD AIR-FILTER DB63-00073B ABS,ZENO BLUE - 1 1 1 1 1 1 1

2-3 BLADE-H DB66-30169A PP,T2.5 1 - - - - - - -BLADE-H DB66-00049A PP,T3 - 1 1 1 1 1 1 1

3 ASSY-BASE DB90-20184L SECC-P,T1 1 - - - - - - -ASSY-BASE DB90-20184B SECC-P,T1 - 1 1 1 1 - - -ASSY-BASE DB90-20184A SECC-P,T1 - - - - - 1 1 1

4 ASSY-COND DB96-00587A ASS'Y 1 - 1 - - - - -ASSY-COND DB96-00587B ASS'Y - 1 - - 1 - - -ASSY-COND DB96-00250B ASS'Y - - - 1 - - - -ASSY-COND DB96-30279A ASS'Y - - - - - 1 1 1

5 ASSY-EVAP DB96-40203C ASS'Y 1 1 1 1 1 - - -ASSY-EVAP DB96-40173A ASS'Y - - - - - 1 - -ASSY-EVAP DB96-40173B ASS'Y - - - - - - 1 1

6 ASSY-FRAME LOW DB90-50133J ASS'Y 1 - - - - - - -ASSY-FRAME LOW DB90-50133A ASS'Y - 1 1 1 1 1 1 1

7 BLOWER DB67-50078A ABS 1 1 - - - - - -BLOWER DB67-50073A ABS - - 1 1 1 1 1 1

9 MOTOR FAN DB31-00074A AFS-095ZREA 1 1 - - - - - -MOTOR FAN DB31-00074E AFS-095ZTEA - - 1 - - - - -MOTOR FAN DB31-00074B AFS-100ZREB - - - 1 - - - -MOTOR FAN DB31-00074D AFS-105ZUEA - - - - 1 - - -MOTOR FAN DB31-00074C AFS-105AUEA - - - - - 1 1 1

10 FAN-PROPELLER DB67-50072A AS,350 1 1 1 1 1 1 1 111 ASSY-CASE-COND DB61-10152A ASS'Y 1 - - - - - - -

ASSY-CASE-COND DB90-00142A ASS'Y - - - - - 1 1 1ASSY-CASE-COND DB90-00142B ASS'Y - 1 1 1 1 - - -

12 ASSY FRAME-UP DB90-50142E ASS'Y 1 - - - - - - -ASSY FRAME-UP DB90-50142F ASS'Y - 1 1 1 1 1 1 1

13 TUBE-CAPILLARY DB96-00387A - 1 1 - - - - - -TUBE-CAPILLARY DB62-00649A - - - 1 - - - - -TUBE-CAPILLARY DB62-00510A - - - - 1 - - - -TUBE-CAPILLARY DB62-00550A - - - - - 1 - - -TUBE-CAPILLARY DB62-31741A - - - - - - 1 1 1

14 TUBE SUCTION DB96-00348B - 1 1 - 1 1 - - -TUBE SUCTION DB96-00931A - - - 1 - - - - -TUBE SUCTION DB62-31742A - - - - - - 1 1 1

15 TUBE-DISCHARGE DB62-00327B - 1 1 1 1 1 - - -TUBE-DISCHARGE DB62-31740A - - - - - - 1 1 1

16 NUT-WASHER DB60-30028A HEX,2C,M8,ZPC 1 1 1 1 1 1 1 117 GROMMET-ISOLATOR DB73-00070A NR 1 1 1 1 1 - - -

GROMMET-ISOLATOR DB73-00067A NR - - - - - 1 1 118 SPRING-OLP DB67-60020A STS304-WPA 1 1 1 1 1 1 1 119 COVER-TERMINAL DB63-10026A NORYL,-,SEI-701 1 1 1 1 1 1 1 120 OLP-POLYESTER DB35-00004Y MRA12109-12007 1 1 - - - - - -

OLP-POLYESTER DB35-00015M RAC12049-9622 - - 1 - - - - -OLP-POLYESTER DB47-20001U MRA98693-12007 - - - 1 - - - -OLP-POLYESTER DB47-20001M MRA12008-12008 - - - - 1 - - -OLP-POLYESTER DB47-20001V MRA12030-12008 - - - - - 1 - -OLP-POLYESTER DB47-20001Z MRA98706-12008 - - - - - - 1 1

21 ROTARY COMPRESSOR:22 44B102HU1EF 115V,60Hz,1Ph,R-22 1 1 - - - - - -ROTARY COMPRESSOR:22 44B102IU1EL 208-230V,60Hz,1Ph,R-22 - - 1 - - - - -ROTARY COMPRESSOR:22 44B124HU1EL 115V,60Hz,1Ph,R-22 - - - 1 - - - -ROTARY COMPRESSOR:22 44B124IU1EL 208-230V,60Hz,1Ph,R-22 - - - - 1 - - -ROTARY COMPRESSOR:22 48A124MV1EL 200-220V,50Hz,1Ph,R-22 - - - - - 1 - -ROTARY COMPRESSOR:22 48A124JV1EL 220-240V,50Hz,1Ph,R-22 - - - - - - 1 1

22 ASSY CABI DB90-00364B ASS'Y 1 - - - - - - -ASSY CABI DB90-00364A ASS'Y - 1 1 1 1 1 1 1

23 BLADE-V DB66-30170A PP,T3 1 1 1 1 1 1 1 124 LEVER-DAMPER DB66-70024A HIPS,T2.5 1 1 1 1 1 1 1 125 ASSY CONTROL DB93-00558A ASSY 1 - - - - - - -

ASSY CONTROL DB93-00559A ASSY - 1 - - - - - -ASSY CONTROL DB93-00674H ASSY - - 1 - - - - -ASSY CONTROL DB93-00571A ASSY - - - 1 - - - -ASSY CONTROL DB93-00587A ASSY - - - - 1 - - -ASSY CONTROL DB93-00674F ASSY - - - - - 1 - -ASSY CONTROL(VIETNAM) DB93-00674M ASSY - - - - - 1 - -ASSY CONTROL DB93-00577A ASSY - - - - - - 1 -ASSY CONTROL DB93-00674L ASSY - - - - - - - 1

26 ASSY REMOCON DB93-00284K ASSY 1 1 - 1 1 1 1 1ASSY REMOCON DB93-00284M ASSY - - 1 - - - - -

2-DB68-02477A(1) 7/2/01 10:07 AM Page 5-12


6-3 Main unit (Type C)

4

1

3

6

5338

9

10

11

15

16

17 24

19 2

021

18

22 23

13

2

14

12

1-

4

1-

2

1-

3

1-

1

32

31

31-

6

31-

12

31-

11

31-

8

31-

7

31-

9

31-

131

-2

31-

4

25

31-

5

31-

10

9-1

14-

1

31-

14

31-

13

34

2-DB68-02477A(1) 7/2/01 10:07 AM Page 5-13


Part List (Type C)


AW1290A AW14FAMBA AW18FAMBA AW18FAMBB AW18FAMCA AW18FAMEA AW18FBMEA AWT18FAMDA AW24FAMBA AW24FAMBB AW24FAMCA WT24FAMEA

1 DB92-70101F ASSY PANEL-FRONT ASSY 1 - - - - - - - - - - -

DB92-00067A ASSY PANEL-FRONT ASSY - 1 1 1 1 1 1 1 1 1 1 1

DB92-00067B ASSY PANEL-FRONT(TAIWAN) ASSY - - 1 - - - - - - - - -

1-1 DB64-10163A GRILLE-AIR INLET HIPS,T2.5 1 - - - - - - - - - - -

DB64-00178A GRILLE-AIR INLET HIPS,M-P/J - 1 1 1 1 1 1 1 1 1 1 1

DB64-00178B GRILLE-AIR INLET(TAIWAN) HIPS,W9391 - - 1 - - - - - - - - -

1-2 DB63-30167C GUARD AIR-FILTER ABS,T2,SC-94445R,- 1 - - - - - - - - - - -

DB63-00100C GUARD AIR-FILTER ZENO BLUE,GREEN - 1 1 1 1 1 1 1 1 1 1 1

1-3 DB66-30205A BLADE-H PP 1 - - - - - - - - - - -

DB66-00120A BLADE-H C-PP,M-P/J - 1 1 1 1 1 1 1 1 1 1 1

DB66-00120B BLADE-H(TAIWAN) PP,W9391(WHT) - - 1 - - - - - - - - -

1-4 DB64-70102A PANEL-FRONT HIPS,T2.5 1 - - - - - - - - - - -

DB64-00177A PANEL-FRONT HIPS,M-P/J - 1 1 1 1 1 1 1 1 1 1 1

DB64-00177B PANEL-FRONT(TAIWAN) HIPS,W9391(WHT) - - 1 - - - - - - - - -

2 DB90-00304A ASSY BASE M-P/J,44B FRAME 1 - - - - - - - - - - -

DB90-00304G ASSY BASE M-P/J,44B DRAIN - 1 - - - - - - - - - -

DB90-00304E ASSY BASE M-P/J,48B DRAIN - - 1 1 1 1 1 1 - 1 - -

DB90-00304F ASSY BASE M-P/J,48/55DW DRAIN - - - - - - - - 1 - 1 -

DB90-20215A ASSY BASE - - - - - - - - - - - 1

3 DB63-40019A TRAY-DRAIN 30FOAM-PS 1 1 1 1 1 1 1 1 1 1 1 1

4 DB96-00654A ASSY EVAP M-P/J,2R*15S 1 1 - - - - - - - - - -

DB96-00254A ASSY EVAP M-P/J,3R*15S - - 1 1 1 1 1 - - - - -

DB96-40207B ASSY EVAP M-P/J,3R*15S - - - - - - - 1 - 1 - -

DB96-00253A ASSY EVAP M-P/J,4R*15S - - - - - - - - 1 - 1 -

DB96-40207A ASSY EVAP 1.7WAVE - - - - - - - - - - - 1

5 DB61-00440A MOUNT MOTOR SGCC-M,T1.2 1 1 1 1 1 1 1 1 1 1 1 1

6 DB31-00075A MOTOR FAN OSME-708SWC,M-P/J 1 - - - - - - - - - - -

DB31-00075J MOTOR FAN OSME-906SWC,M-P/J - 1 - - - - - - - - - -

DB31-00075E MOTOR FAN AFS145ZUEA,M-P/J - - 1 1 1 - - - 1 1 1 -

DB31-00075H MOTOR FAN OSME-1404SAC,M-P/J - - - - - 1 1 - - - - -

DB31-00075F MOTOR FAN OSME-1206SWC,M-P/J - - - - - - - 1 - - - -

DB31-00085A MOTOR FAN OSME-1256SWC,M-P/J - - - - - - - - - - - 1

8 DB96-00026A EVAP-PLATE CASING ASSY 1 1 1 1 1 1 1 1 - - - 1

DB96-00026B EVAP-PLATE CASING ASSY - - - - - - - - 1 1 1 -

9 DB67-00096A BLOWER ABS+G/F20%,M-P/J 1 1 1 1 1 1 1 1 1 1 1 1

9-1 DB60-30002A NUT-WASHER M6 1 1 1 1 1 1 1 1 1 1 1 1

10 DB61-00609A CASE EVAP 30FOAM-PS,WHT 1 1 - - - 1 1 1 - - - -

DB61-10182A CASE EVAP 30FOAM-PS - - 1 1 1 - - - 1 1 1 1

11 DB63-10487A COVER-EVAP PP,T2.5 1 1 1 1 1 1 1 1 1 1 1 1

12 DB70-10679A PLATE-PARTITION SGCC-M,T0.8 1 1 1 1 1 1 1 1 1 1 1 1

13 DB61-00448A CASE COND PP(TALC),T2.5,BLK 1 1 1 1 1 1 1 1 1 1 1 -

DB61-10183A CASE COND PP,T2 - - - - - - - - - - - 1

14 DB67-00047A FAN-PROPELLER ABS,M-P/J 1 1 1 1 1 1 1 1 1 1 1 -

DB67-50028A FAN-PROPELLER ABS+GLASS-FIBER - - - - - - - - - - - 1

14-1 DB60-30004A NUT-WASHER M6,SM20C 1 1 1 1 1 1 1 1 1 1 1 1

15 DB96-00664A ASSY COND M-P/J,2R*19S*560 1 1 - - - - - - - - - -

DB96-00328B ASSY COND 1.7 D,HEX,SF - - 1 1 1 - - - 1 1 1 -

DB96-00328A ASSY COND ASSY - - - - - 1 1 - - - - -

DB96-00092A ASSY COND 4X16,WAVE2.0 - - - - - - - 1 - - - -

DB96-00328B ASSY COND 1.7,D,HEX,SF - - - - - - - - 1 1 1 -

DB96-30358A ASSY COND 1.7WAVE - - - - - - - - - - - 1

16 DB62-00566A TUBE CAPILLARY 2.75 1 - - - - - - - - - - -

DB62-00596A TUBE CAPILLARY AW14FAMBA,-,-,- - 1 - - - - - - - - - -

DB62-00519A TUBE CAPILLARY 2.75 - - 1 - 1 1 1 - - 1 - -

DB62-00588A TUBE CAPILLARY 2.75,22K - - - 1 - - - - - - - -

DB96-00283A TUBE CAPILLARY 1.2X1000X3 - - - - - - - 1 - - - -

DB62-00516A TUBE CAPILLARY 2.75,24K - - - - - - - - 1 - 1 -

DB62-31988A TUBE CAPILLARY C1220T-H,1.3 - - - - - - - - - - - 1

17 DB62-00563A TUBE SUCTION 12K 1 1 - - - - - - - - - -

DB62-00518A TUBE SUCTION 18K - - 1 1 1 1 1 - - - - -

DB62-00518C TUBE SUCTION OD12.7,24K - - - - - - - 1 - 1 - -

DB62-00515A TUBE SUCTION 24K - - - - - - - - 1 - 1 -

DB62-31987B TUBE SUCTION C1220T-O,T0.8 - - - - - - - - - - - 1

18 DB62-00534B TUBE DISCHARGE OD9.52 1 1 - - - - - - - - - -

DB62-00457B TUBE DISCHARGE OD9.52 - - 1 1 1 - - 1 - 1 - -

DB62-00067C TUBE DISCHARGE C1220T-0,OD9.52,T0.7 - - - - - 1 1 - - - - -

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-14


Part List (Type C)


AW1290A AW14FAMBA AW18FAMBA AW18FAMBB AW18FAMCA AW18FAMEA AW18FBMEA AWT18FAMDA AW24FAMBA AW24FAMBB AW24FAMCA WT24FAMEA

DB62-00514A TUBE DISCHARGE 9.52,24K - - - - - - - - 1 - 1 -

DB62-00025A TUBE DISCHARGE 24K - - - - - - - - - - - 1

19 DB60-30018A NUT-FLANGE PI0.8,M5,SM20C 1 1 1 1 1 1 1 1 1 1 1 -

20 DB63-10026A COVER-TERMINAL NORYL 1 1 1 1 1 1 1 1 - 1 - -

DB63-00038A COVER-TERMINAL NORYL,T2,BLK - - - - - - - - 1 - 1 -

21 DB47-20001U OLP MRA98693-12007 1 - - - - - - - - - - -

DB35-00015H OLP RAC12074-9622 - 1 - - - - - - - - - -

DB35-00004W OLP MRA12107-12007 - - 1 - 1 - - - - - - -

DB35-00015E OLP RAC12016-9622 - - - 1 - - - - - - - -

DB47-20001P OLP MRA12016-12007 - - - - - 1 1 - - - - -

DB35-00004X OLP MRA12108-12007 - - - - - - - 1 - - - -

DB47-20002Z OLP MRA12 - - - - - - - - - 1 - -

22 DB60-30028A NUT-WASHER HEX,2C,M8,ZPC,-,- 1 1 1 1 1 1 1 1 1 1 1 1

23 DB73-00070A GROMMET ISOLATOR NR 35 1 1 - - - - - - - - - -DB73-00067A GROMMET ISOLATOR NR - - 1 1 1 1 1 1 - 1 - -

DB73-00041A GROMMET ISOLATOR EPDM,DAEWOO - - - - - - - - 1 - 1 -

24 44B124HU1EL COMPRESSOR 115V,60Hz 1 - - - - - - - - - - -

44B135IU1EL COMPRESSOR 208-230V,60HZ - 1 - - - - - - - - - -

48B175IV1EH COMPRESSOR 208-230V,60Hz - - 1 - 1 - - - - - - -

48B190IV1EH COMPRESSOR 208-230V,60Hz - - - 1 - - - - - - - -

48B180JV1EH COMPRESSOR 50Hz,220-240V - - - - - 1 1 - - - - -

48B180MT1EH COMPRESSOR 200-220V,50HZ - - - - - - - 1 - - - -

DB95-00113C COMPRESSOR EDB260211A,230V,60Hz - - - - - - - - 1 - 1 -

48B220IV1EH COMPRESSOR 60Hz,208-230V - - - - - - - - - 1 - -

DB95-10351B COMPRESSOR AWG5532EXC - - - - - - - - - - - 1

25 DB64-00138J CABINET SGCC-M,SC-94445T 1 - - - - - - - - - - -

DB64-00138A CABINET SECC-P,SC-94445T - 1 1 1 1 1 1 1 1 1 1 1

31 DB93-00484P ASSY CONTROL-E ASSY 1 - - - - - - - - - - -

DB93-00484W ASSY CONTROL-E ASSY - 1 - - - - - - - - - -

DB93-00484H ASSY CONTROL-E ASSY - - 1 - 1 - - - - - - -

DB93-00484X ASSY CONTROL-E(TAIWAN) ASSY - - 1 - - - - - - - - -

DB93-00484L ASSY CONTROL-E ASSY - - - 1 - - - - - 1 - -

DB93-00484N ASSY CONTROL-E ASSY - - - - - 1 - - - - - -

DB93-00774B ASSY CONTROL-E ASSY - - - - - - 1 - - - - -

DB93-00484M ASSY CONTROL-E ASSY - - - - - - - 1 - - - -

DB93-00774G ASSY CONTROL-E(VIETNAM) ASSY - - - - - - - 1 - - - -

DB93-00484K ASSY CONTROL-E ASSY - - - - - - - - 1 - 1 -

DB93-00717A ASSY CONTROL-E ASSY - - - - - - - - - - - 1

32 DB66-70024A LEVER-DAMPER HIPS,T2.5 1 1 1 1 1 1 1 1 1 1 1 1

DB66-70024C LEVER-DAMPER(TAIWAN) HIPS,T2.5,W9391 - - 1 - - - - - - - - -

33 DB61-60125A FRAME-BLADE HIPS,T2.5 1 1 1 1 1 1 1 1 1 1 1 1

34 DB93-00284K ASSY REMOCON W-RAC,ARC-709 1 - 1 1 1 1 1 1 1 1 1 1

DB93-00284M ASSY REMOCON W-RAC,ARC-710 - 1 - - - - - - - - - -

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-15


6-3 Assy Control

7

6

5

4

3

13

10

914

8

2

12

111

Part List (Type A)


AW0690A AW0790A AW07FASAA AW07FASAA(TAIWAN)

AW07FASBA(TAIWAN)

AW07FASEA AW0890A AW09FASBA AW09FASEA AW09FBSEA

1 DB61-00417A CASE CONTROL-LOW SGCC-M,T0.8 1 1 1 1 1 1 1 1 1 12 DB61-00419A CASE CONTROL-UP SM(E) SGCC-M,T0.8 1 1 1 1 1 1 1 1 1 13 2501-001227 C-OIL 30uF,400V 1 - - - - - - - - -

2501-001226 C-OIL 25uF,400V - 1 - 1 1 1 - - - -2501-001216 C-OIL 35/5uF,370V - - 1 - - - - - - -2501-001228 C-OIL 35uF,400V - - - - - - 1 - - -2501-001225 C-OIL 20uF,400V - - - - - - - 1 - -2501-001236 C-OIL 30uF,450V - - - - - - - - 1 1

4 DB65-10008B CLIP-CAPACITOR SGCC-M,T0.8 1 1 1 1 1 1 1 1 1 15 2301-001450 C-FILM,MPE-PPF 4500nF,440V 1 - - - - - - - - -

2301-001449 C-FILM,MPE-PPF 6000nF,440V - 1 - - - - 1 - - -2301-001367 C-FILM,MPE-PPF 6000nF,450V - - - 1 - - - - - -2301-001370 C-FILM,MPE-PPF 2500nF,450V - - - - - 1 - - - -2301-001369 C-FILM,MPE-PPF 3000nF,450V - - - - 1 - - 1 1 1

6 DB26-00006B TRANS-POWER AC115V,50Hz/60Hz,DC17V 1 1 1 1 - - 1 - - -DB26-00006A TRANS-POWER AC230V,50Hz/60Hz,DC17V - - - - 1 1 - 1 1 1

7 DB31-00084A MOTOR-SYNCHRONOUS M2CK59ZT79-H 1 1 1 1 - - 1 - - -DB31-00084B MOTOR-SYNCHRONOUS M2LJ49ZV32 - - - - 1 1 - 1 1 1

8 DB93-00407A ASSY PCB MAIN ASSY 1 1 - - - - 1 - - -DB93-00407B ASSY PCB MAIN ASSY - - 1 1 1 1 - 1 1 -DB93-00407D ASSY PCB MAIN ASSY - - - - - - - - - 1

9 DB64-00259A PANEL CONTROL-S(E) HIPS,T2.0 1 1 1 1 1 1 1 1 1 110 DB34-00013B SWITCH MEMBRANE 99*134.5,PC 1 1 1 - - 1 1 1 1 1

DB34-00015B SWITCH MEMBRANE(TAIWAN) 99.1*134.5,PET - - - 1 1 - - - - -11 DB32-10051A THERMISTOR 10K/25,3425K 1 1 1 1 1 1 1 1 1 112 DB39-00343A POWER CORD-ASS'Y 125V,13A,TANDEM 1 1 1 1 - - 1 - - -

DB39-00342A POWER CORD-ASS'Y(TAIWAN) 250V,16A,TANDEM - - - - 1 - - - - -DB39-00348A POWER CORD-ASS'Y HONG KONG,250V,15A - - - - - 1 - - 1 1DB39-00344A POWER CORD-ASS'Y 250V,13A,TANDEM - - - - - - - 1 - -

13 DB66-70031A ARM-BLADE PS 1 1 1 1 1 1 1 1 1 114 DB64-00321A WINDOW REMOCON 1 1 1 1 1 1 1 1 1 1

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-16


Part List (Type B)


AW1090A AW10FAJAA AW10FAJBA AW12FAJAA AW12FAJBA AW12FAJDA AW12FAJEA AW12FBJEA

1 DB34-00013B SWITCH MEMBRANE 99x134,PC 1 1 - 1 1 1 1 1DB34-00015B SWITCH MEMBRANE 99.1x134.5,PET - - 1 - - - - -

2 DB64-00259A PANEL CONTROL-S(E) HIPS,T2.0 1 1 1 1 1 1 1 13 DB93-00407A ASSY PCB MAIN ASSY 1 - - - - - - -

DB93-00407B ASSY PCB MAIN ASSY - 1 1 1 1 1 1 -DB93-00407D ASSY PCB MAIN ASSY - - - - - - - 1

4 DB61-00421A CASE CONTROL-UP J(E) SGCC-M,T0.8 1 1 1 1 1 1 1 15 DB31-00084A MOTOR-SYNCHRONOUS M2LJ49ZV32 1 1 - 1 - - - -

DB31-00084B MOTOR-SYNCHRONOUS M2LJ49ZV32 - - 1 - 1 1 1 16 2501-001229 C-OIL 40uF,400V 1 1 - - - - - -

2501-001234 C-OIL 20uF,450V - - 1 - - - - -2501-001230 C-OIL 45uF,400V - - - 1 - - - -2501-001236 C-OIL 30uF,450V - - - - 1 1 1 1

7 DB65-10008B CLIP-CAPACITOR SGCC-M,T0.8 1 1 1 1 1 1 1 18 DB66-70022D ARM-BLADE PS,SC-96527R 1 1 1 1 1 1 1 19 DB39-00343B POWER CORD-ASS'Y 125V,15A,PARALLEL 1 1 - 1 - - - -

DB39-00342A POWER CORD-ASS'Y 250V,16A,TANDEM - - 1 - - - - -DB39-00344A POWER CORD-ASS'Y 250V,13A,TANDEM - - - - 1 - - -DB39-10089Q POWER CORD-ASS'Y 250V,15A - - - - - 1 - -DB39-00348A POWER CORD-ASS'Y 250V,15A - - - - - 1(VIETNAM) 1 1

10 2301-001448 C-FILM,MPE-PPF 8000nF,440V 1 - - - - - - -2301-001381 C-FILM,MPE-PPF 8000nF,450V - 1 - - - - - -2301-001370 C-FILM,MPE-PPF 2500nF,450V - - 1 - - - - -2301-001452 C-FILM,MPE-PPF 15000nF,250V - - - 1 - - - -2301-001378 C-FILM,MPE-PPF 3500nF,450V - - - - 1 - 1 12301-001379 C-FILM,MPE-PPF 4000nF,450V - - - - - 1 - -

11 DB26-00006B TRANS-POWER AC115V,50Hz/60Hz 1 1 - 1 - - - -DB26-00006A TRANS-POWER AC230V,50Hz/60Hz - - 1 - 1 1 1 1

12 DB61-00417A CASE CONTROL-LOW SGCC-M,T0.8 1 1 1 1 1 1 1 113 DB32-10051A THERMISTOR 10K/25,-,3425K 1 1 1 1 1 1 1 114 DB64-00321A WINDOW REMOCON 1 1 1 1 1 1 1 1

5

11

10

7

6

8

1

2

3

4

9

14

1312

Exploded View and Parts List

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-17


6

127

8

11

9

1

215

4

5

10

1413

Exploded View and Parts List

Part List (Type C)


AW1290A AW14FAMBA AW18FAMBA AW18FAMBB AW18FAMCA AW18FAMEA AW18FBMEA AWT18FAMDA AW24FAMBA AW24FAMBB AW24FAMCA AWT24FAMEA

1 DB34-00013A SWITCH MEMBRANE 99*144.2,PC 1 1 1 1 1 1 1 1 1 1 1 1DB34-00015A SWITCH MEMBRANE(TAIWAN) 99.1*144.2,PET - - 1 - - - - - - - - -

2 DB64-00261A PANEL CONTROL-M(E) HIPS,T2 1 1 1 1 1 1 1 1 1 1 1 14 DB93-00407A ASSY PCB MAIN ASSY 1 - - - - - - - - - - -

DB93-00407B ASSY PCB MAIN ASSY - 1 1 1 1 1 - 1 1 1 1 1DB93-00407D ASSY PCB MAIN ASSY - - - - - - 1 - - - - -

5 DB61-00419A CASE CONTROL-UP SM(E) SGCC-M,T0.7 1 1 1 1 1 1 1 1 1 1 1 16 DB31-10152A ASSY-MOTOR SWING M2CK59ZT19-H 1 - - - - - - - - - - -

DB95-20065F ASSY-MOTOR SWING M2LJ49ZU3 - 1 1 1 1 1 1 1 1 1 1 17 2301-001448 C-FILM,MPE-PPF 8000nF,440V 1 - - - - - - - - - - -

2301-001367 C-FILM,MPE-PPF 6000nF,450V - 1 1 1 1 1 1 1 1 1 1 18 DB65-10008B CLIP-CAPACITOR SGCC-M,T0.8 1 1 1 1 1 1 1 1 1 1 1 19 DB66-00186A ARM-BLADE POM,BLK 1 1 1 1 1 1 1 1 1 1 1 110 DB39-00343B POWER CORD-ASS'Y 125V,15A,PARALLEL 1 - - - - - - - - - - -

DB39-00342A POWER CORD-ASS'Y 250V,16A,TANDEM - 1 1(TAIWAN) - - - - - - - - -DB39-00344A POWER CORD-ASS'Y 250V,13A,TANDEM - - 1 - 1 - - - - - - -DB39-00345A POWER CORD-ASS'Y 250V,15A,TANDEM - - - 1 - - - - - 1 - -DB39-00348B POWER CORD-ASS'Y HONG KONG,250V,15A - - - - - 1 1 1(VIETNAM) - - - -DB39-10089R POWER CORD-ASS'Y 250V,15A - - - - - - - 1 - - - -DB39-00200B POWER CORD-ASS'Y SPT,250V,20A - - - - - - - - 1 - 1 -DB39-10001K POWER CORD-ASS'Y 240V,60HZ,20A - - - - - - - - - - - 1

11 2501-001230 C-OIL 45uF,400V,BK 1 - - - - - - - - - - 12501-001236 C-OIL 30uF,450V - 1 - - - - - - 1 - 1 -2501-001237 C-OIL 35uF,450V - - 1 - 1 - - - - - - -2501-001238 C-OIL 40uF,450V - - - 1 - 1 1 - - 1 - -2501-001239 C-OIL 45uF,450V - - - - - - - 1 - - - -

12 DB26-00006B TRANS-POWER AC115V,50Hz/60Hz 1 - - - - - - - - - - -DB26-00006A TRANS-POWER AC230V,50Hz/60Hz - 1 1 1 1 1 1 1 1 1 1 1

13 DB61-00417A CASE CONTROL-LOW SGCC-M 1 1 1 1 1 1 1 1 1 1 1 114 DB32-10051A THERMISTOR 10K/25,3425K 1 1 1 1 1 1 1 1 1 1 1 115 DB64-00321A WINDOW REMOCON 1 1 1 1 1 1 1 1 1 1 1 1

2-DB68-02477A(1) 6/28/01 11:35 AM Page 5-18

7. Block Diagram

7-1 Refrigerating Cycle Block Diagram

PINCH PIPE(SERVICE VALVE) SUCTION LINE

ACCUMULATOR/COMPRESSOR

EVAPORATOR

CAPILLARY TUBE

CONDENSER

DISCHARGE LINE

PINCH PIPE(SERVICE VALVE)

7-2 Basic Structure

7-2-1 Micom Control Diagram

A/D converter

Swing motor control

Compressor control

Buzzer control

Temperature control

Fan motor control

Reset Circuit

Led display control

Remocon SingleReceiving

Compressor

Fan motor

Power circuit (DC 5V)

Oscillation Circuit

Membrane Pad control

Energe saver Temp.set(, ) Operation, Mode Swing, Sleep Fan select, Timer

Remocon single control

MAIN MICOM

Room Temperature sensor

Receiving Unit of Remocon

EEPROM

Swing motor

Powercircuit (DC 12V)

Down Trans (AC15V)

Power input (AC230V), (AC115V)

(Key operation)

(Remocon control)


Operation

Swing

Timer

Sleep

Fan speed (high)

Fan speed (med)

Fan speed (low)

Fan

Cool

Energy saver

Temp.setting()

Temp.setting()

(Remote Control)

2-DB68-02477A(1) 6/28/01 11:35 AM Page 7-1


7-2-2 Micom Pin Assignment

KS88C4716

GRID5

SEG-DATA(d)

SEG-DATA(e)

SEG-DATA(f)

SEG-DATA(g)

SEG-DATA(h)

SEG-DATA(a)

EEPROM CLK

EEPROM IN

EEPROM OUT

BUZZER

AUTO RESTART OPTION

JIG OUTPUT

OPTION

SENSOR THERMISTOR(103AT)

OPTION (HEAT PUMP)

OPTION (HEAT PUMP)

OPTION (HEAT PUMP)

OPTION (HEAT PUMP)

ENERGY SAVER OPTION

SWING MOTOR

GND

SEG-DATA(c)

SEG-DATA(b)

GRID4

GRID3

Vcc

Vss

10MHz RESONATOR

10MHz RESONATOR

TEST

GRID2

GRDI1

RESET

KEY-IN1

KEY-IN2

REMOCON SINGLE RECEIVE

EEPROM CS

LOW FAN

COMPERSSOR

MED FAN

HIGH FAN

OPTION (HEAT PUMP)

Vcc

1 P0.1 P4.4 44

2 P0.0 P0.2 43

3 P4.3 P0.3 42

4 P4.2 P0.4 41

5 VDD P0.5 40

6 VSS P0.6 39

7 Xout P0.7 38

8 Xin P1.0 37

9 TEST P1.1 36

10 P4.1 P1.2 35

11 P4.0 P1.3 34

12 RESET P1.4 33

13 P2.0 P1.5 32

14 P2.1 P3.7 31

15 P2.2 P3.6 30

16 P2.3 P3.5 29

17 P2.4 P3.4 28

18 P2.5 P3.3 27

19 P2.6 P3.2 26

20 P2.7 P3.1 25

21 P4.5 P3.0 24

22 AVref AVss 23

2-DB68-02477A(1) 6/28/01 11:35 AM Page 7-2

8. PCB Diagram


8-1 ASSY Main PCB (Code No ; DB93-00407A, B, D)

DB93-00407A( I ) DB93-00407B( II ) DB93-00407D(III)

2-DB68-02477A(1) 6/28/01 11:35 AM Page 8-1


Part List

NO. CODE-NO DESCRIPTION SPECIFICATION 1 2 3 REMAKRS

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

-

1405-000147

DE13-20017A

DE13-20009A

DE13-20016A

DE13-20008A

DE60-10100A

DE62-30031A

-

-

-

-

-

-

3711-003407

-

-

DE32-10037A

-

DE30-20016A

2001-001172

-

-

-

-

-

-

-

-

-

2004-001137

2004-000218

-

-

-

-

-

-

-

-

-

DB09-00091A

3501-001058

2802-000103

DB07-00010A

3501-000399

-

-

DIODE-RECTIFIER

VARISTOR

IC-DRIVE

IC

IC-VOLT REGU

IC-VOLT REGU

SCREW TAPPING

HEAT SINK

C-AL

C-AL

C-AL

C-AL

CONNECTOR WAFER

CONNECTOR WAFER

CONNECTOR WAFER

CONNECTOR WAFER

CONNECTOR WAFER

FUSE

FUSE HOLDER

BUZZER

R-CARBON

REMOCON MODULE

CONNECTOR WAFER

JUMPER WIRE

JUMPER WIRE

JUMPER WIRE

PCB-MAIN

R-CARBON

R-CARBON(2012)

R-CARBON(2012)

R-CARBON

R-CARBON

R-CARBON(2012)

R-CARBON(2012)

C-CERAMIC(2012)

C-CERAMIC(2012)

C-CERAMIC(2012)

C-CERAMIC(2012)

TRANSISTOR

TRANSISTOR

DIODE-SWITCHING(SMALL)

IC-MCU

RELAY-POWER

CERAMIC RESONATOR

LED DISPLAY

RELAY

R-CARBON

IC-MASK ROM

1T4

470V 4500A

KID65003AP

KA7533Z

KA7805A

KA7812A

PH-3 L6

A6063 L23.5 W30

2200F 25V

1000F 35V

100F 10V

22F 16V

YW396-03AV YEL

YW396-03AV WHT

YW396-05AV WHT

JSW250-02 RED

JSW250-03 RED

250V 3.15A

FB 58 20MM

CSB2220BA

620 OHM 1/2W

KSM713TE5

FCZ254-08S

PI0.6 52MM

PI0.6 52MM

3216 TYPE

FR-1 81.5*134.5

RD 1/4W 180-J

MCR10 330-J

MCR10 10K-J

RD 1/8W 6.8K-F

RD 1/8W 10K-F

MCR10 1K-J

MCR 100K-J

MCR21 2F 104Z

MCR21 2F 223Z

MCR21 2F 101Z

MCR21 2F 102Z

KRA226S

KRC246S

1N4148

KS88C4716

ID 1U

10MHz

ELF-316GWB

JQ1A 12V

MCR10 4.7K-J

P93LC56B

4

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

24

1

7

1

8

5

9

1

2

1

1

9

4

1

3

5

1

5

1

1

1

1

4

1

0

4

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

24

1

7

1

8

5

10

1

2

2

1

9

4

1

3

5

1

5

1

1

1

1

4

0

0

4

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

24

0

7

1

8

5

10

1

2

1

1

9

4

1

3

5

1

5

1

1

1

1

4

0

1

D101~D104

VA71

IC03, IC07

IC05

IC02

IC01

C102

C101

C103

C104

CN11

CN71

CN73

CN41

CN12

F701

F701

BZ61

R601

RM41

CN91

J1~J13, J15~J24, J32

OP01

J25~J31

R903~R910

R404~R406, R415, R902

R301, R407, R408, R410~R414, R501, R901(R411)

R403

R401, R402

R201, R202

R409

C105, C106, C401~C406, C410

C501, C502, C601, C901

C407

C408, C409, C902

Q901~Q905

Q906

D901~D905

IC04

RY71

X501

RY72, 73, 75, 76

R411

IC06

2-DB68-02477A(1) 6/28/01 11:35 AM Page 8-2


9-1 AW0690A/AW0790A/AW07FASA/AW0890A/AW09FSA/AW1090A/AW10FAJA9-1 AW12FJA/AW1290/AW14FAMBA/AW18FAMA/AWT18FAMDA/AW24FAMBB

DIAGRAM - ELECTRIC DB68-02015A

9. Wiring Diagram

CN73

2-DB68-02477A(1) 6/28/01 11:35 AM Page 9-1


9-2 AW24FAMBA/AW24FAMCA/AWT24FAMEA

DIAGRAM - ELECTRIC DB68-02053A

CN73

2-DB68-02477A(1) 6/28/01 11:35 AM Page 9-2

10. Schematic Diagrams

10-1 Main PCB (AW0690A/AW0790A/AW07FASA/AW0890A/AW09FASA/AW1090A/AW10FAJA/AW12FAJA/AW1290A/AW14FAMBA/AW(T)18FAMA/AW(T)24FAMA)


No. RESISTOR VALUE UNIT OF TEMP. OPTION

R41110K-J C

4.7K-J F

OPTION

10-2 Main PCB (AW09FBSEA/AW12FBJEA/AW18FBMEA)


No. RESISTOR VALUE UNIT OF TEMP. OPTION

R41110K-J C

4.7K-J F

OPTION


10-3 Remote Control

(KEY NAME)K29 : SAVEK37 : TIMERK39 : SLEEPK41 : AIR SWINGK49 : TEMP. ()K50 : TEMP. ()K53 : LOW FANK54 : MED FANK55 : HIGH FANK57 : FANK60 : COOLK63 : ON/OFF

2-DB68-02477A(1) 6/28/01 11:35 AM Page 9-3

manual de servicio samsung awt24famea

Documents

thepower cord

proper parts

parts list7

exactreplacement parts

measurethe resistance

insulation resistance

proper toolsand test

product specifications2