machine tools and devices for special technologies water beam machining slovak university of...
TRANSCRIPT
![Page 1: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/1.jpg)
Machine Tools And Devices For Special Technologies
Water Beam Machining
Slovak University of TechnologyFaculty of Material Science and Technology in Trnava
![Page 2: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/2.jpg)
Machining by water beam
ecologic without impact effective cold cut Various materials
metal, ceramics, plastic, foods, others...
![Page 3: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/3.jpg)
Principle of machining by water beam Erosion influence of water – small flash,
high pressure (more than 400 MPa),
Water is in the cut place like solid material.
In the cutting of hard and brittle materials is into water mix in abrasive.
![Page 4: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/4.jpg)
Principle of water beam machiningAccording by cutting material are realised two
mechanisms of material removal:
brittle material – begining and extension of cracks originated by influence of tension by impacted water beam,
tensional material – begin of sliding fracture by shearing stresses.
![Page 5: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/5.jpg)
Kinds of water beam
Continually Linear,
clean, cryogenic,
cavitation, abrasive,
AWJ Abrasive Water Jet (around 500 MPa), ASJ Abrasive Suspension Jet (till 100 MPa),
Discontinually Low-frequency, High-frequency
![Page 6: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/6.jpg)
Clean water beamClean water without
substances.Preparing of water –
recommended.
Material with low firmness (textile, foods, gum).
Diameter of beam 0,1 till 0,3mm, jet distance from surface maximum 15mm
![Page 7: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/7.jpg)
Cryogenic water beam
Into water beam the frazils of water or CO2 of sferic shape are mixed in during expasion.
Using in food industry and in medicine for bio materials cutting.
![Page 8: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/8.jpg)
Cavitation water beam
In water beam are cavitation bubbles that can influence into material local 10 multiply increase of pressure during impact.
Glass cutting, rocks and etc.
![Page 9: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/9.jpg)
Abrasive water beamInto water beam is mixed in suitable abrasive.It is
used for strong brittle, hard machining materials (300 – 500 MPa, clean water above1000 MPa).
Abrasives: Heavy:
granat, Carbide of silicon (SiC), Steel scobs,
light: Silica sand, glass.
![Page 10: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/10.jpg)
AWJ – side mixing in of abrasivea – water input,
b – abrasive input,
c – water beam abrasive output,
1 – water,
2 – mixture room,
3 – abrasive,
4 – jet with colimator,
5 – cutting material,
6 – water beam with abrasive
Usage of abrasive: 0,5 till 20 kg/min
![Page 11: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/11.jpg)
ASJ
Abrasive is into pressure water mixed in in pressure container. This suspenzion is directed into special jeet.
Abrasive usage: 1 till 3 kg/min
![Page 12: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/12.jpg)
Discontinual water beamPressure generated by impact of water beam is
particular multiply higher than pressure generated by continual water column.
By impact of discontinual (pulsing) beam originated impact pressure that next decreased to zero. This cycle is repeat with the frequency.
Pulsation with low frequency, Discontinuous beam, modulated beam.
![Page 13: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/13.jpg)
Water beam cutting process
Cutting process consist of two phases:
By water pressure influence become hollow that is transformed to hole,
Creating of sawed joint.
![Page 14: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/14.jpg)
Process of water beam cuttingAreas in cutting surface:
In the side of the input – mat aspect with roughness Ra = 2 till 5,5m
In the side of output – gaining with wave lenght 1 till 2mm
![Page 15: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/15.jpg)
Quality of cutting surface
More quality cutting surface: Increasing of cutting speed, Increasing of pressure, Increasing of volume flash of abrasive, Increasing of dynamic beam stability.
By various parameter setting we achieve quality of cutting surface that be suitable for requests.
![Page 16: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/16.jpg)
Quality of cutting surface
Q1 – dividing cut, Q2 – rough cut, Q3 – intermediate cut, Q4 – fine cut, Q5 – the best cut.
![Page 17: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/17.jpg)
Cutting surface shape
Cutting speed is with respect to hardness of cutting material small. Water beam comes in time for erode cutting sawed joint into his natural shape.
![Page 18: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/18.jpg)
Cutting surface shape
Cutting speed is correct, cutting surfaces are without scarf.
![Page 19: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/19.jpg)
Shape of cutting surface
Cutting speed is with respect to hardness of cut material high. Water beam is not coming in time for particularly eroding of bottom cut part and that is in down direction closed.
![Page 20: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/20.jpg)
Devices for water beam cutting Water preparing:
filtration, deionisation, softening,
High-pressure pump: Low-pressure oil cycle, High-pressure water cycle,
Cutting station: Cutting desk, portal, support, Cutting head with cutting jet
![Page 21: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/21.jpg)
Water preparing filtration – mechanical preparing, removing
elements of size around 1m, deionisation – removing of the ion waste
elements, ion transmission, softening – water hardness preparing is
recommend to using of soft water. Back osmose – water is pressed through the
semipermiable membrane that is stopped soluble materials.
High lifetime of device (jet, pump), increased quality of cutting surface.
![Page 22: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/22.jpg)
High-pressure pump
Low-pressure oil cycle – oil pressure is 15 till 35MPa. There are used standard generators.
High-pressure water cycle – created water cutting pressure of asked rate (100 till 500MPa). There can be individually a few.
Exclusively high-pressure elements!!
![Page 23: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/23.jpg)
High-pressure pump
![Page 24: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/24.jpg)
Processing of high-pressure pump
![Page 25: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/25.jpg)
Cutting desk
Filled in with water that stopped the energy of water beam,
Filling in and filling out of water, Firm construction, Type of construction:
In the floor is assembled system with dividing cutting desk, Integrated system desk-portal, Console system with dividing cutting desk, Integrated system desk– console.
![Page 26: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/26.jpg)
In the floor assembled system with dividing cutting system
![Page 27: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/27.jpg)
Iintegrated system desk - portal
![Page 28: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/28.jpg)
Console system with dividing cutting system
![Page 29: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/29.jpg)
Integrated system desk - console
![Page 30: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/30.jpg)
Next parts of cutting device
Portal – makes possible to moving of support above desk, can has several cutting heads,
Support – holds cutting head above desk, positioning by servomotors, cutting heads is setting in the vertical axis Z, cutting head can be rollovering.
Cutting head – is imbed by jet, there can by various shapes of jets.
![Page 31: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/31.jpg)
Cutting heads
For cutting by clean water,
For cutting of abrasive water beam
![Page 32: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/32.jpg)
Cutting head jet
For clean water beam – diameter 0,05 till 0,5 mm Sintered carbide, Synthetic sapphire, Synthetic diamond,
For abrasive water beam – diameter 0,8 till 2,2mm Wolfram carbide (WC) Cubic nitride of boron (KBN) ceramics
Lifetime around 100hours.
![Page 33: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/33.jpg)
Jet shapes of cutting head
Stair-step, conic, combinated.
![Page 34: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/34.jpg)
Examples of technology using
![Page 35: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/35.jpg)
Examples of technology using
![Page 36: Machine Tools And Devices For Special Technologies Water Beam Machining Slovak University of Technology Faculty of Material Science and Technology in Trnava](https://reader036.vdocuments.mx/reader036/viewer/2022081519/56649dc65503460f94abb3f7/html5/thumbnails/36.jpg)
Example of desk with two cutting heads