machine design elements

MACHINE DESIGN RECALL VIQ PAST BOARD - MACHINE DESIGN

1

INSTRUCTION: Select the correct answer for each of the following questions. Mark only one answer for each item by shading the box corresponding to the letter of your choice on the answer sheet provided. STRICTLY NO ERASURES ALLOWED. Use pencil No. 2 only 1. Determine the estimated weight of an A-36 steel plate size 3/16

x 6 x 20 A. 919 lbs * C. 829 lbs B. 1012 lbs D. 735 lbs

2. The minimum clearance allowed for meshing spur gears with a

circular pitch of 0.1571 and diametral pitch of 20. The spur gear has 25 teeth. A. 0.007855 * C. 0.007558 B. 0.008578 D. 0.007585

3. A 3 diameter short shaft carrying two pulleys close to the

bearings transmit how much horsepower if the shaft makes 280 rpm? A. 199 Hp * C. 200 Hp B. 198 Hp D. 210 Hp

4. What pressure is required to punch a hole 2 diameter through a

steel plate? A. 10 tons C. 30 tons B. 20 tons D. 40 tons *

5. Compute the working strength of 1 bolt which is screwed up

tightly in packed joint when the allowable working stress is 13,000 psi. A. 3600 lbs C. 3900 lbs * B. 3950 lbs D. 3800 lbs

6. What is the working strength of a 2 bolt which is screwed up

tightly in a packed joint when the allowable working stress 12,000 psi? A. 20,120 lbs C. 20.400 lbs * B. 20,400 lbs D. 20,200 lbs

7. Compute the speed of the gear mounted on a 52.5 mm diameter

shaft receiving power from a driving motor with 250 hp. A. 2182 rpm C. 2282 rpm * B. 2071 rpm D. 2341 rpm

8. The minimum whole depth of spur gear of 14-1/2 deg. involute

type with diameter pitch of 24 and circular pitch of 0.1309: A. 0.09000 C. 0.089875 * B. 0.09900 D. 0.089758

9. Heating of the metal to a temperature above the critical

temperature and then cooling slowly usually in the furnace to reduce the hardness and improve the machinability is called: A. annealing * C. normalizing B. tempering D. quenching

10. What is the frictional HP acting on a collar loaded with 100 kg

weight? The collar has an outside diameter of 100 mm and an internal diameter of 40mm. The collar rotates at 1000 rpm and the coefficient of friction between the collar and the pivot surface is 0.15. A. 0.8 HP * C. 0.3 HP B. 0.5 HP D. 1.2 HP

11. A solid cylindrical shaft 48.2 cm long is used for a transmission of

mechanical power at a rate of 37 KW running at 1760 rpm. The Ss is 8.13 MPa. Calculate the diameter A. 30 mm C. 40 mm B. 35 mm D. 50 mm *

12. An internal gear is set up with a 5-in diameter pinion and center

distance of 18 inches. Find the diameter of the internal gear. A. 36 C. 26 B. 21.5 D. 41 *

13. What force P is required to punch a in. hole on a 3/8 in. thick

plate if the ultimate shear strength of the plate is 42,000 psi? A. 24,940 lbs C. 24,960 lbs B. 24,620 lbs D. 24,740 lbs *

14. A 2.5 diameter by 2 in. long journal bearing is to carry a 5500-lb

load at 3600 rpm using SAE 40 lube oil at 200 F through a single hole at 25 psi. Compute the bearing pressure. A. 1100 psi * C. 1000 psi B. 900 psi D. 950 psi

15. In a uniformly loaded simple beam, the maximum vertical

shearing force occurs

A. at the center C. at beam bottom fiber B. at the section of maximum momentD. at either end support *

16. A hollow shaft has an inner diameter of 0.035 m and outer

diameter of 0.06 m. Determine the polar moment of inertia of the hollow shaft. A. 1.512 x 10-6 m4 C. 1.52 x 10-6 m4 B. 1.215 x 10-6 m4 D. 1.125 x 10-6 m4 *

17. Determine the thickness of a steel air receiver with 30 inches

diameter and pressure load of 120 psi, design stress of 8000 psi. A. 1`/4 in. * C. 3/8 in. B. 5/8 in. D. in.

18. A short 61 mm shaft transmits 120 Hp. Compute the linear

speed of a pulley 55 cm mounted on the shaft.

A. 1796 fpm C. 1856 fpm * B. 1766 fpm D. 2106 fpm

19. A 2-in. solid shaft is driven by a 36-in. gear and transmits power

at 120 rpm. If allowable shearing stress is 12 ksi, what horsepower can be transmitted? A. 29.89 C. 38.89 B. 35.89 * D. 34.89

20. Using oxyacetylene welding method to weld a 3 ft. long seam in a

3/8 in. thick plate at a consumption rate of 9 cu. ft. /ft. of weld for oxygen and 7 cu. ft./ft. for acetylene. What is the total combined gas consumption in cu. ft. ? A. 51 C. 45 B. 48 * D. 55

21. A coiled spring with 5 cm of outside diameter is required to work

under the load of 190 N. The wire diameter is 5 mm, the spring is to have 6 active coils and the ends are to be closed and ground. Determine the total number of coils. The modulus of rigidity is 809 GPa and the mean radius is to be 23 mm, with 7 mm pitch of the spring. A. 6.5 coils C. 8.5 coils * B. 7.5 coils D. 9.5 coils

22. A helical spring having squared and ground ends has a total of 18

coils and its material has modulus of elasticity in shear of 78.910 GPa. If the spring has an outside diameter of 10.42 cm and a wire diameter of 0.625 cm, compute in the spring due to a load of 50 kgs. A. 302 mm C. 490 mm * B. 490 mm * D. 322 mm

23. Design the size of solid steel shaft to be used for a 500 hp, 250

rpm application if the allowable torsional deflection is 1 and the allowable stress is 10,000 psi modulus of rigidity is 13 x 106 psi. A. 5 dia. C. 4-7/8 dia. * B. 4-5/8 dia. D. 4-3//4 dia.

24. With the electric are welding rate of 18 in./min, how long will it

take to weld a in. thick plate by 3 ft long seam? A. 3 min. C. 1.5 min. B. 2 min. * D. 4 min.

25. How long will it take to mill a 3/4 by 2 long keyway in a 3

diameter shafting with a 24 tooth cutter turning at 100 rpm and 0.005 feed/tooth? A. 0.136 min. C. 0.166 min. * B. 0.196 min. D. 0.106 min.

26. How long will it take to saw a rectangular piece of aluminum plate

8 in. wide and 1 1/2 in. thick if the length of the cut is 8 in., the power hacksaw makes 120 rev/min and average feed per stroke is 0.0060 in.? A. 13.11 C. 14.01 B. 11.11 * D. 12.03

27. A cast iron flywheel is rotated at a speed of 1200 rpm and having

a mean rim radius of 1 foot. If the weight of the rim is 30 lbs. what is the centrifugal force? Use factor C = 41. A. 14,800 lbs C. 14,860 lbs B. 7 ft D. 14,760 lbs *

28. A steel cylindrical air receiver with 5 ft diameter and pressure load

of 180 psi, design stress of 9500 psi maximum. The pressure vessel is to be provided with 1 in. diameter drain valve installed at the bottom of the vessel and safety pressure relief valve installed either at the top most or at the side with pop out rating of 200 psi. Assume a 100 % weld joint efficiency. The lap welding tensile strength is 65,000 psi. Determine the bursting pressure of this air receiver. A. 1154 psi C. 1454 psi


2

B. 1354 psi * D. 1254 psi 29. The tooth thickness of a gear is 0.5 inch and its circular pitch is

1.0 inch. Calculate the dedendum of the gear. A. 0.3183 C. 0.3979 * B. 1.250 D. 0.1114

30. A holllow shaft has an inner diameter of 0.035 m and an outer

diameter of 0.06 m. Compute for the torque if the shear stress is not to exceed 120 MPa in Nm. A. 4500 * C. 4300 B. 4100 D. 4150

31. The path of contact in involute gears where the force/power is

actually transmitted. It is a straight imaginary line passing through the pitch point and tangent to the base circle. A. principal reference plane C. front angle B. pitch point D. line of action *

32. It is a problem of expansion and shrinkage of steel material so

that the slightly bigger shafting of 2 diameter can be inserted / fitted to the slightly smaller hole of a steel bushing of 1.999 diameter with the following process/material/data to apply: Coefficient of expansion of carbon steel = 0.0000068 in/in F Temperature raised by gas heating = 24.5 F Cooling media to use dry ice with boiling point of -109.3 F (-78.5 C) Shrinkage rate below boiling point is 0.00073 in/in Determine the final clearance between the expanded steel bushing hole against the shrinkage of the steel shaft. A. 0.000793 in. * C. 0.000750 in. B. 0.000693 in. D. 0.000800 in.

33. What modulus of elasticity in tension is required to obtain a unit

deformation of 0.00105 m/m from a load producing a unit tensile stress of 44,000 psi? A. 42.300 x 106 psi C. 43.101 x 106 psi B. 41.202 x 106 psi D. 41.905 x 106 psi *

34. Compute the pitch angle of a bevel gear given the pinions number

of teeth of 14 and 42 teeth on the gear.

A. 18.4 * C. 33.4

B. 28.4 D. 38.4 35. Compute for the tooth thickness of 141/2 spur gear with diameter

pitch = 5. A. 0.3979 C. 0.03141 B. 3.1831 D. 0.31416 *

36. What is the difference between a shaper and a planer?

A. the tool of the shaper moves while on the planer is stationary *

B. the shaper can perform slotting operation while the planer cannot

C. the shaper handles large pieces while the planer handle only small pieces

D. the tool of the shaper moves in reciprocating motion while the tool in the planer moves in rotary motion

37. If the ultimate shear strength of a steel plate is 42,000 lb/in2,

what force is necessary to punch a 0.75 inch diameter hole in a 0.625 inch thick plate? A. 63.008 lbs C. 61,800 lbs * B. 68,080 lbs D. 66,800 lbs

38. A steel tie rod on bridge must be made to withstand a pull of 5000

lbs. Find the diameter of the rod assuming a factor of safety of 5 and ultimate stress of 64,000 lb/in2 A. 0.75 in. C. 0.84 in. B. 0.71 in * D. 0.79 in.

39. If the weight of 6 diameter by 48 long SAE 1030 shafting is

174.5 kg. then what will be the weight of chromium SAE 51416 of same size? A. 305.5 lbs C. 384.6 lbs * B. 426.4 lbs D. 465.1 lbs

40. Compute the circular pitch (in inch) of a pair of gears having a

ratio of 4 and a center distance of 10.23. Each gear has 72 teeth and pinion has 18 teeth. A. 0.8095 C. 0.8035 B. 0.7825 * D. 0.8085

41. A journal bearing with diameter of 76.2 mm is subjected to a load

of 4900 N while rotating at 200 rpm. If its coefficient of friction is 0.02 and L/D = 2.5, find its projected area in mm2. A. 12,090 C. 13,050 B. 14,165 D. 14,516 *

42. A flywheel rotates at 120 rpm or 12.57 rad/sec slowed down to 102 rpm or 10.68 rad/sec during the punching operation that requires second of the punching portion of the cycle. Compute the angular acceleration of the flywheel in rad/sec2. A. -2.52 rad/sec2 * C. -2.75 rad/sec2 B. 3.15 rad/sec2 D. 2.22 rad/sec2

43. A drop hammer of 1 ton dead weight capacity is propelled down

ward by a 12 in diameter cylinder. At 100 psi air pressure what is the impact velocity if the stroke is 28 inches? A. 63.2 fps C. 31.6 fps * B. 15.8 fps D. 47.4 fps

44. Compute the nominal shear stress at the surface in MPa for a 40

mm diameter shaft that transmits 750 kW at 1500 rpm. Axial and bending loads assumed negligible. Torsional shearing stress is 28 N/mm2. A. 218 C. 232 B. 312 D. 380 *

45. A truck skids to stop 60 m after the application of the brakes while

travelling at 90 km/hr. What is the acceleration in m/sec2? A. -5.21 m/s2 * C. -7.06 B. 6.36 D. 5.76

46. A spur pinion rotates at 1800 rpm and transmits to a mating gear

30 HP. The pitch diameter is 4 and the pressure angles pressure angle is 14 1/2. Determine the tangential load in lbs. A. 495 C. 535 B. 525 * D. 475

47. A high alloy spring having squared and ground ends and has a

total of 16 coils and modulus of elasticity in shear of 85 GPa. Compute the Wahl factor. The spring outside diameter is 9.66 cm and wire diameter is 0.65 cm. A. 1.058 C. 1.185 B. 1.10 * D. 1.2

48. Two idlers of 28 T and 26 T are introduced between the 24 T

pinion with a turning speed of 400 rpm driving a final 96 T gear. What would be the final speed of the driven gear and its direction relative to the driving gear rotation? A. 120 rpm and opposite direction B. 100 rpm and opposite direction * C. 80 rpm and same direction D. 100 rpm and same direction

49. Compute the line shaft diameter to transmit 12 HP at 180 rpm

with torsional deflection of 0.08 degrees per ft length. A. 3 in. C. 2.35 in * B. 5 cm D. 62 mm

50. The allowable stresses that are generally used in practice are 4 ksi

for main power transmitting shaft, 6 ksi for line shaft carrying pulleys and 8.5 ksi for small short shaft/countershaft, etc. With these allowable stresses what will be the simplified formula to determine transmitted HP, diameter of the shaft or even the rpm(N)? A. HP=D3N/80 C. all of these * B. HP=D3N/531/2 D. HP=D3N/38

51. Calculate the rpm for machining a cast iron workpiece 6 inches in

diameter. The lowest cutting speed for cast iron is 50 fpm. A. 35.3 C. 43.3 B. 33.3 * D. 53.32

52. A helical gear a 14 0 normal pressure angle and transverse

diameter pitch of 2.3622 per cm. the helix angle is at 45 and has 8 teeth. Compute the transverse pressure angle in degrees.

A. 22.2 C. 18.9

B. 19.3 D. 20.1 * 53. Compute the maximum unit shear in a 3 inch diameter steel

shafting that transmits 2400 in lb. of torque at 99 rpm. A. 4530 psi * C. 3860 psi B. 4250 psi D. 4930 psi

54. To facilitate the milling (roughing) work of a cast steel material

using material using a 11/2 inch diameter cutter choose between the two available stock. Find the speed of the cutter in rpm. -high speed steel cutter with a cutting speed of 50 fpm -carbide tipped cutter with a cutting speed of 200 fpm

A. 389 C. 509 * B. 572 D. 412 55. The U.S standard gage for iron and steel was established in 1893

which is primarily a weight gage. The basis is the weight of wrought iron which is at _______ lbs. per cubic foot. A. 480 * C. 490


3

B. 493 D. 488 56. Calculate the cutting speed in fpm when spindle speed of a lathe

is turning 8 inch diameter bronze casting using a spindle speed of 120 rpm. A. 220 fpm C. 2510 fpm B. 3016 fpm D. 251 fpm *

57. The lathe compound is used for:

A. angle cutting C. facing * B. grooving D. shaping

58. If the ultimate shear stress of a 1/8 inch thick drawn steel plates

is 35 ksi what force is required to punch a 1 1/2 inch diameter hole? A. 10.011 lbs C. 11 Mtons B. 22.322 lbs D. 20620 lbs *

59. Brazing is more superior than soldering in joining metals because:

A. all of these * B. molten metal flaws between joints because of capillary forces C. it has slight diffusion of metal involved D. higher melting temperature joining

60. To finally complete milling (finishing) work of steel material the

operator has the option to choose the better available cutter in stock and these are:

-both 1 1/2 inch diameter -high speed steel with recommended cutting speed of 90 fpm -carbide tipped with cutting speed of 300 fpm

Compute the rpm of the cutter A. 801 C. 764 *

B. 620 D. 264 61. A ball is thrown vertically upward with a speed of 24.38 m/s. Then

2 seconds later a second ball is projected vertically upward too with a speed of 18.28 m/s. At what point above will they meet? A. 17.62m C. 16.62 m * B. 15.62 m D. 21.62 m

62. Babbit bearing material maybe melted in a pouring ladle over an

open fire. The temperature is about right when a wooden pine stick used for stirring chars but does not ignite and at that stage

the molten metal temperature is in the vicinity of ________ F. A. 1010 C. 760 B. 870 * D. 590

63. The purpose of______is to prevent gears from jamming together

and making contact on both sides of their teeth simultaneously A. tooth fillet C. backlash * B. stress relieving D. all of these

64. Any internal/residual stress in a steel work can be remedied by:

A. tempering C. annealing B. stress relieving D. all of these *

65. The usual shrinkage allowance specified for patterns to

compensate for the expected shrinking of cast steel parts construction of steel casting in cooling: A. 1/8 inch/ft C. 3/32 to 1/8 inch/ft B. 3/16 inch/ft * D. 5/32 to 7/32 inch/ft

66. Choose the economical type of material for gears that give/sustain

good operating quality/life for intended operation A. plane carbon steel C. all of these B. high alloy steel D. heat treated carbon steel *

67. A material plane was subjected to a load. When the load was

removed the strain disappeared. From the structural change which of the following can be considered about this material? A. it does not follow Hookes Law C. it is elastic * B. it has high modules of elasticity D. it is plastic

68. Compute the power transmitted in HP by the shaft rotating 1200

rpm and subjected to torsional moment of 1200 MN. A. 202 * C. 150 B. 252 D. 171

69. Instantaneous center is also called___________

A. all of these C. centro B. virtual center * D. rotopole

70. What is the stress to strain ratio within the elastic limit?

A. elastic limit C. elasticity B. modulus of elasticity * D. compressive ratio

71. A spur pinion supported on each side by ball bearings rotates 1750 rpm and transmit to a mating gear at 25 Hp. The pressure angle is 20 degrees and the pitch diameter is 5. Determine the tangential load in lbs.

A. 420 C. 360 * B. 300 D. 400

72. In a spring design, spring index of 7 through 9 is best 4 through 7

and 9 through 16 are often used but spring index of________should be avoided due to difficulties in making etc. A. all of these C. 5 or less B. less than 5 * D. 4

73. Allowance added in the casting pattern to compensate for the

contraction of metal A. tapering allowance C. finish allowance B. shrinkage allowance * D. draft pattern

74. Ratio of the angle of action to the pitch angle

A. contact ratio * C. ratio of gearing B. approach ratio D. module

75. General purpose grade of steel used for broiler plate, structurals

etc. usually with carbon content of______. A. 0.20 to 0.30%C * C. all of these B. 0.35 to 0.50%C D. 0 .15 to 0.25%C

76. The angle made by the helix of the thread(in a straight thread) at

the pitch diameter with a plane perpendicular to the axis called__________ A. angle of thread C. lead angle * B. truncation D. lead

77. The principle materials used in the production of metal working

tools: A. high carbon steel * C. titanium, phosphorous B. tungsten, silicon, hadfield Mn D. vanadium, chromium, molybdenum 78. In the interest of design simplification and good kinematic

compromise bevel gears adopted a standard pressure angle of ___________degrees.

A. 20 involute stub C. 141/2 involute full depth

B. 20 * D. 171/2 79. The property of material that relates the lateral strain to

longitudinal strain. A. stress C. Poissons circle * B. strain D. endurance limit

80. Also called eccentrically loaded bearing is ________.

A. full bearings C. partial bearing B. offset bearing * D. fitted bearings

81. In the selection of wire rope, regular lay means wires and strands

are arranged in the following manner: A. twisted in the same direction C. twisted in opposite direction * B. twisted in any direction D. twisted in along direction

82. In involute teeth, the pressure angle is often defined as the angle

between the line of action and the line of tangent to the pitch circle. It is also termed as- A. helix angle C. Angle of obliquity * B. angle of recess D. Arc of action

83. A lineshaft runs at 360 rpm. An 18 pulley on the same shaft is

belt connected to a 12 pulley on the countershaft. From a 15 pulley on the countershaft motion is transmitted to the machine. Compute/check the required of the pulley on the machine to give a spindle speed of 660 rpm. A. 16 C. 101/2 B. 12 1/4 * D. 81/2

84. Height of tooth above pitch circle or the radial distance between

pitch circle and top land of the tooth. A. top root C. land B. addendum * D. hunting tooth

85. The function of clutch in the machine tool is?

A. lowering of drive speed B. to disconnect or connect at will the drive * C. alignment of drive shaft D. to insure that two shaft line up at high speed

86. It is generally recommended and normal for a designer to add a

hunting tooth to evenly distribute the wear on meshing teeth like a 53 teeth gears mesh with 30 teeth pinion. Find the rotation of pinion to mesh with same pair of teeth again A. 120 C. 61 B. 81 D. 53 *

87. The shaft whose torque varies from 2000 to 6000 in lbs has 1 1/2 in in diameter and 60000 psi yield strength. Compute for the shaft mean average stress. A. 6036 psi * C. 5162 psi


4

B. 6810 psi D. 5550 psi 88. The angle made by the helix of the thread (in a straight thread) at

the pitch diameter with a plane perpendicular to the axis is called__________. A. lead angle * C. lead B. truncation D. angle of thread

89. The rule of thumb in journal bearing design; the clearance ratio/clearance should be. A. 0.0090 C. 0.0010 * B. 0.0042 D. 0.00120

90. The moment of inertia of a rectangle whose base is b height h

about its base is A. bh3/4 C. bh3/24 B. bh3/12 D. bh3/3 *

91. Cold rolled shafting is not available in diameter larger

than__________ A. 6 inches C. 6 inches B. 5 inches * D. 5 inches

92. What power would a spindle 55 mm in diameter transmit at 480

rpm. Stress allowed for short shaft is 59 newtons/mm2 A. 45.12 kw * C. 45 Hp B. 50.61 kw D. 39.21 kw

93. The cast iron flywheels are commonly designed with a factor of

safety of______ A. 14 to 15 C. 8 to 9 B. 10 to 13 * D. 6 to 12

94. A pair of equal and opposite (not collinear) forces that tend cause

a rotation of a body A. couple * C. equilibrium B. centroids D. vector

95. The ratio of the pitch diameter in inches to the number of teeth

A. pitch circle C. module B. English module * D. pitch diameter

96. When the motion is diminished/decreasing instead of increasing is

called. A. deceleration C. retarded motion * B. uniform negative impulse D. all of these

97. _______is a unit or energy?

A. ft.-lb. * C. BTU/hr. B. hp D. watt

98. When high strength and durability are a requirements for choosing

gear materials it is preferable to use_________material A. hardened bronze C. phenolic laminated B. steel * D. white iron

99. _________forces when action are parallel

A.. couple C. resultant B. non collinear D. non concurrent *

100. The product of the mass and the velocity of the center of gravity

of the body is called. A. linear momentum * C. linear impulse B. angular impulse D.angular momentum

101. Two parallel shaft connected by pure rolling turn in the same

direction and having a speed ratio of 2.75. what is the distance of the two shaft if the smaller cylinder is 22 cm. in diameter. A. 16.60 cm C. 25.25 cm B. 30.25 cm D. 19.25 cm *

102. The distance between similar, equally-spaced tooth surfaces in a

given direction and along a given line. A. pitch circle C. pitch * B. pitch plane D. pitch diameter

103. A drop hammer of 1 ton dead weight capacity is propelled

downward by a 12 inch diameter cylinder. At 100 psi air pressure what is the impact velocity if the stroke is 28 inches? A. 47.4 ft/sec C. 15.8 ft/sec B. 31.6 ft/sec * D. 63.2 ft/sec

104. Could be defined as simply push and pull.

A. power C. work B. inertia D. force *

105. Opposite directional forces equal in magnitude and parallel is

called_________ A. non coplanar C. couple *

B. centroid D. coplanar 106. Quantities such as time , volume and density are completely

specified when their magnitude is known is also called A. couple C. components B. resultants D. scalar *

107. The use of hardened steel for the mating metal gear appears to

give the best results and longer operational life. The usual hardness is in the range of- A. over 600 BHN * C. below 350 BHN B. 300 to 400 BHN D. over 400 BHN

108. _______is the product of the resultant of all forces acting on a

body and the time. A. linear momentum C. angular momentum B. linear impulse * D. all of these

109. The separate forces which can be so combined are called

A. concurrent forces C. couple B. non concurrent forces D. component forces *

110. Continuous stretching under load even if the stress is less than the

yield point A. plasticity C. creep * B. elasticity D. ductility

111. The most known lubricants being utilized in whatever category of

load and speed are oil, air, grease and dry lubricants like A. bronze C. silicon B. lead D. graphite *

112. A coupling that allows axial flexibility/movement in the operation.

Made of alternate bolting of steel, leather, fabric and/or plastic material into the two flanges A. Flexible disk coupling * B. flexing Oldham coupling C. Flexible toroidal spring coupling D. Elastic-material bonded coupling

113. It consists of two cranks, a stationary piece called the line of

centers and the connecting rod is a A. five-bar linkage C. three-crank linkage B. four-crank braces D. four-bar linkage *

114. Used to change rotary motion to reciprocating

motion____________ A. rack gears * C. Helical gears B. hypoid gears D. herringbone gears

115. The effective face width of a helical gear divided by gear axial

pitch A. approach ratio * C. Arc of recess B. Arc of action D. Face overlap

116. Pitch diameter less the diameter of the roller chain is equal to:

A. top land C. addendum B. bottom diameter * D. Face overlap

117. Generally applied on speed reducer due to large speed ratio:

A. bevel gears C. worm gears * B. helical gears D. hypoid gears

118. If shaft size is specified as-diameter 2.00 max. and 1.99 min. in

diameter then the 0.010 could be defined as________ A. allowance C. variance B. fit D. tolerance *

119. A material plane was subjected to a load. When the load was

removed the strain disappeared. From the structural change which of the following can be considered about this material? A. it has high modules of elasticity C. it is plastic B. it does not follow Hookes Law D. it is elastic *

120. Helix angle in the range of ______ degree is recommended for

wide-face helical gears A. less than 15 * C. 20 to 35 B. less than 20 D. 20 to 22

121. A step shaft made of SAE 1117 steel with an ultimate strength of

69.7 ksi. The notch sensitivity factor is 0.983 and 0.00435 is the constant dependent upon the ultimate strength check the radius of the stress raiser. A. 0.192 C. 0.25 * B. 0.386 D. 0.775

122. Difference between maximum material limits of mating parts . Or

it is a minimum clearance or maximum interference between parts A. tolerance C. variance


5

B. fits D. allowance * 123. The changes in shape or geometry of the body due to action of a

force on it is called deformation or _____ A. shear stresses C. compressive stress B. stresses D. strains *

124. For an evenly distributed and uniform wear on each meshing gear

tooth, the ideal design practice is to consider a______________ A. wear resistance alloy addition to tooth gears B. heat treatment of the gears C. hardening of each tooth D. hunting tooth addition *

125. The reciprocal of a diametral pitch or the ratio of the pitch

diameter to the no. of teeth A. lead C. involute B. module * D. clearance

126. Ability to resist deformation under stress

A. plasticity C. stiffness * B. all of these D. toughness

127. Flat leather belting not recommended for used in a speed in

excess of____fpm. A. 3600 C. 6000 * B. 4800 D. all of these

128. The angle included between the sides of the thread measured in

an axial plane in a screw thread A. angle of thread * C. Helix angle thread

B. Angle between thread or 40 D. Half angle thread or 20 129. An elastic body whose primary function is to deflect under load

A. clutch C. brake B. stopper D. spring *

130. Determine the estimated weight of a x 6 x 20 steel plate

A. 1809 kgs C. 1709 kgs B. 1490 kgs D. 1666 kgs. *

131. Steel plates allowable tensile strength

A. 396.41 N/m2 * C. 379.31 N/m2

B. 296.12 N/m2 D. 310.11 N/m2 132. Poissons Ratio is the ratio of

A. elastic limit to yield strength B. lateral deformation to the longitudinal deformation * C. shear strain to unit strain

D. elastic limit to shear strength

133. Manganese steel standard designation, SAE_______

A. 13xx * C. 11xx B. 10xx D. 8xx

134. One of these materials is not a structural steel?

A. low carbon steel C. stainless steel B. tool and die steel * D. medium carbon steel

135. Determine the torque received by the motor shaft running at 4250

rpm. Transmitting 11 Hp, through a 10 in diameter 20 involute gear. The shaft is supported by ball bearings at both ends and the gear is fixed at the middle of 8 shaft length A. 163 in lb. * C. 132 in. lb. B. 167 in. lb D. 138 in. lb.

136. The ratio of moment of inertia on a cross-section of a beam to this

section modulus is A. a measure of distance * B.equal to the radius of gyration and compression C. multiplied by the bending moment of inertia to determine the yield stress D. equal to the area of the cross-section and tension

137. The SAE 2340 shafting contain___________% Nickel

A. 3.85 Ni C. 3.25 to 3.75 % Ni * B. 4% Ni D. 3.84% Ni

138. Chromium steel standard designation SAE___________

A. 92xx C. 3xxx B. 5xxx * D. 11xx

139. Alloy that improves strength of steel at high temperature

application A. aluminum C. silicon B. manganese D. chromium *

140. When an air entraintment agent is put into a concrete mix

A. the water/cement ratio must be reduced B. the strength will decrease * C. minimal effect D. the strength will suffer up to 50%

141. In general, alloys with high nickel content retain toughness to

quiet low temperatures up to ______ oF. A. -380 C. -260 B. -400 D. -320 *

142. The differential of the shear equation is the ______ .

A. deflection of the beam C. tensile strength of beam B. comprehensive strength of the beamD. load on the beam *

143. It is recommended not to have a direct drive between driven and

drive sprockets if the ratio of their teeth exceeds _______. Use 2 or more step combination. A. 10 times C. 5 times B. 8 times * D. 6 times

144. The length of the hub should not be made lesser than the face

width of the gear. Hub lengths usually vary from 1 25D to 2D where d is the shaft diameter. The reasonable diameter of steel hub should be- A. 2D C. 1.55 D B. 1.8 D * D. 1.20 D

145. Length of contact between two mating parts in a screw and nut

threads measured axially is termed______. A. Length of Engagement * C. Arc of contacts B. Axis of contact D. Depth of Engagement

146. The sum of their addendums and dedendums

A. whole depth * C. width of space B. full depth D. working depth

147. Stresses that are independent of loads is called__________

A. working stress C. simple stress B. residual stresses * D. combined stress

148. Material having a high electrical resistance and should not be used

as conductor of electrical current A. nickel * C. silicon base alloys B. aluminum oxide D. iron oxide

149. The best materials for brake drums is______.

A. aluminum C. steel material B. cast iron * D. wrought iron

150. The alloy materials used in the production of metal working tools

A. titanium, phosphorous C. vanadium, chromium, molybdenum B. tungsten, silicon, hadfield mn D. high carbon steel *

151. Torsional deflection is a significant consideration in the design of

shaft and the limit should be in the range of_____________degree/foot of length A. 0.4 to 1 C. 0.08 to 1 * B. 0.1 to 1 D. 0.6 to 1

152. If the pitch of a screw is 2/9 find the thread per inch

A. 0.34 C. 5.4 B. 4.5 D. 17

153. The property that characterizes a materials ability to be drawn

into a wire A. tensile strength C. endurance limit B. ductility * D. thermal conductivity

154. For steel shafting design in an average condition the maximum

distance in feet between bearing to avoid excessive linear

deflection is by formulas- L=8.95 3 2D or 8.95 D2/3 for shaft

subjected to no bending except its own weight but for shafting with bending action of pulleys etc. the formula then will be L= __________ A. 4 D2/3 C. 5.2 D2/3 * B. 7.0 D 2/3 D. 6.0 D2/3

155. Which of the phases of steel elements has a face-centered cubic

structure? A. pyrite C. all of these B. austenite * D. cementite

156. Steel spring material is usually hardened to 400 to 500 BHN and

the carbon content is in the range of____ A. 0.50 to 0.90 % * C. 0.45 to 0.48 B. all of these D. 0.96 to 0.97

157. Principal stresses occur on these plane


6

A. which are subjected to ultimate tension B. which are subjected to maximum compression C. The shearing stress is zero *

D. which are 45 apart 158. The property of material wherein the content is continuously

distributed through its entire mass A. plasticity C. homogeneity * B. malleability D. all of these

159. The properties of metal to withstand loads without breaking down

is A. elasticity C. plasticity B. strength * D. strain

160. Shafts readily available in the market are made in many ways and

wide variety of material composition. It is likely be cold drawn carbon steel in size smaller than __________inches diameter A. 3.75 * C. 5 B. 4 D. 51/2

161. Plain carbon steel standard designation SAE________

A. 6xxx C. 10xx * B.13xx D. 2xxx

162. If the inertia is 90 lb. ft2 and the speed of the driven shaft is to be

increased from 0 to 2500 rpm in 5 seconds, shaft material is of SAE 4140 with yield strength of 110000 lbs./in2, find the clutch starting torque in in. lb ft. A. 159 C. 146 * B. 128 D. 191

163. The rigidity of polymer can be increased by

A. fumace melting C. crystallization * B. normalizing D. shot opening

164. The difference between cast steel and cast iron

A. all of these B. cast steel has usually less than 1 % C. while cast iron has 2% or 3.6% carbon range D. cast iron has lower strength more brittle and has lower ductility than cast steel *

165. It is a general practice to use the following allowable stresses

4000 psi for maintransmitting shaft and 8500 psi for small short shafts and counter shaft . for lineshaft carrying pulley it is______psi A. 7800 C. 6000 * B. 7000 D. 6500

166. How many 5/16 inch holes can be punch in one motion in a steel

plate made of SAE 1010 steel 7/16 inch thick using a force of 55 tons. The ultimate strength for shear is 50 ksi and use 2 factor of safety A. 5.8 C. 5 * B. 3.7 D. 6.5

167. Drilling machine cannot do-

A. reaming C. lapping B. spot facing * D. broaching

168. Material charges in foundry melting operation are composed of

A. limestone, foundry coke and silica sand * B. steel scrap alloys and charcoal/foundry coke C. iron ore, quartz and charcoal D. scrap wood alloys and limestone

169. ________is a work-supporting device which is bolted to the saddle

of the lathe machine. It travels with the cutting tool it is a prevention of the springing away of the workpiece from cutting tools A. rubber-flex collets C. follower rest * B. tool post D. carriage stop

170. Almost always the soldering materials are a combination of the

following alloys A. all of these C. tin & antimony B. lead & tin * D. lead & antimony

171. The most popular of all soldering materials in use has composition

of. A. 45/55% tin & lead C. all of these B. 50/50% tin & lead * D. 60/40% tin & lead

172. The relative strength of a butt welding could be safety assumed as____% efficiency. A. 95 C. 90 * B. 98 D. 92

173. Which of the following raw materials are used in the foundry molding operation? A. silica sand, bentonite, flour/paste water * B. silica sand paste,graphite electrode C. silica sand and paste D. silica sand, linseed oil, flour

174. The following are parts of a micrometer caliper except for

A. thimble C. spindle B. head screw * D. anvil

175. To avoid brittleness of weld or the residual stress in the welding it

is normally stress relieved of___ A. normalizing C. flame hardening B. tempering * D. annealing

176. Steel with certain % of carbon maximum can readily be welded by

all process and the resulting strength of the portion welded is as strong as the base material A. 0.15% C max C. 0.25 % C max B. 0.35 % C max D. 0.30%C max *

177. A kilowatt is equal to_________

A. 8851.2 in-lb/sec. C. 57 BTU/min * B. 1140 joule/sec. D. 44.200 ft. lb./min.

178. Molybdenum-chromium-nickel steel designation

A. SAE48xx C. SAE56xx B. SAE43xx * D. SAE46xx

179. Single forces which produces the same effect upon a mass

replacing two or more forces acting together is called A. vector C. component of forces B. resultant * D. resolution

180. Permissible variation of the manufactured/machined dimension is

called ___________ A. intolerance fits C. allowance B. deviation D. tolerance *

181. Peculiar strength of the metal to resist being crushed

A. shear strength C. compressive strength * B. ultimate strength D. elastic limit

182. What pressure is required for punching a hole 2 dia thru steel

plates? A. 40 tons * C. 45 tons B. 50 tons D. 35 tons

183. What is the working strength of a 2 bolt which is screwed up

tightly in a packed joint when the allowable working stress is 12,000 psi A. 20.4 ksi * C. 23.4 ksi B. 22.4 ksi D. 18 ksi

184. Determine the bursting steam pressure of a steel shell with

diameter of 10 inches and made of thick steel plate. The joint efficiency is at 70% and the tensile strength is 60 ksi A. 4200 psi * C. 42.8 ksi B. 10.5 ksi D. 8500 psi

185. Commonly used by steel melter as deoxidizer because of its easy

availability and cheap price A. silicon C. zinc B. aluminum * D. manganese

186. Curve formed by the path of a point on a straight line as it rolls

along a convex base curve. The base curve is usually a circle and generally used as the profile of gear tooth. A. axial plane C. arc or recess B. involute * D. arc of action

187. Resultant of two or more component forces is called___________

A. composition of forces * C. component B. resultant D. collinear of forces

188. A material having a high electrical resistance and should not be

used for conductor of electric current A. alloyed magnesium C. nickel * B. silicon base alloy D. zinc

189. A radian is equal to_________

A. 57.020 C. 57.296 *

B. 57.706 D. 57.190 190. It improves red hardness of steel

A. silicon C. cobalt * B. lead D. manganese

191. Designated pipe color used in communication


7

A. silver gray C. bare B. aluminum gray D. white *

192. The design stress and factor of safety are related in the following

manner A. design stress = ultimate stress/ factor of safety * B. ultimate stress = factor of safety / design stress plus concentration factor C. factor of safety = design stress / ultimate stress D. design stress = factor of safety / times stress concentration factor

193. Not adaptable to welding due to low tensile strength and poor

ductility etc A. copper parts C. aluminum parts * B. cast iron materials D. bronze parts

194. Bearing surface that completely surrounds the journal is also

called_______ A. offset bearing C. centrally loaded bearing B. full bearing * D. babbit bearing

195. The purpose of lubrication is as mentioned except

A. to lighten the load * C. prevent adhesion B. prevent corrosion/oxidation D. cool the moving elements

196. Tools usually used in wood pattern making in foundry shop.

A. saws and chisels * C. knives and drills B. band saw D. drill machine

197. ________is a plane perpendicular to the axial plane and to the

pitch plane in gears the parallel axes; and the plane of rotating coincide A. tangent plane C. transverse * B. straight plane D. reference plane

198. A 36 tooth pinion with a turning speed of 300 rpm drives 120

tooth gear of 14 degrees involute full depth pressure angle . What would be the speed of the driven gear? A. 1000 rpm C. 90 rpm * B. 100 rpm D. 140 rpm

199. Several force which can be combined is called.

A. resultants C. components * B. composition of forces D. collinear forces

200. The surface along the fillet curves or between the fillets radius of

the two adjacent tooth or a gear A. bottom land * C. fillet B. flank D. top land

201. Ideal herringbone gear helix is in the range of__________

A. 30 to 45 * C. 25 to 30 B. 35 to 50 D. 15 to 20

202. The lack of backlash in a spur gear design/operation may result to

__________ A. overloading C. all of these * B. jamming D. overheating

203. The distance from a point on a screw thread to a corresponding

point on the next thread measure along the axis A. flank C. crest B. lead D. pitch *

204. As recommended the center to center distance between sprockets

should not be less than ____ times the bigger sprocket A. 2.216 C. 1 1/2 * B. 1 3/4 D. 2.59

205. Machine shop instrument for checking the flatness of plane

surfaces to 10ths of thousandths of a centimeter A. blade type micrometer C. planimeter * B. dial caliper D. micrometer

206. Molybdenum steel standard designation SAE___________

A. 88xx C. 40xx * B. 48xx D. 46xx

207. Determine the minimum mean diameter of a taper pin for use to

fix a lever to a shaft if it is transmit a max torque of 700 in-lbs. The shaft diameter is 2 inches and the material allowable stress is 15000 psi. Use factor of safety of 2. A. 7.0 mm C. 5.2 mm B. 7.2 mm D. 6.2 mm *

208. Recommended design practice for steel lineshafting to limit the

linear deflection to ________inch/foot of length (maximum) A. 0.020 C. 0.012

B. 0.010 * D. 0.15 209. A link has a load factor of 0.8 the surface factor of 0.8 ; the

surface factor is 0.92 and the endurance strength is 28000 psi. Compute the alternating stress of the link if it is subjected to a reversing load. Assume a factor of safety of 3. A. 8150 C. 9,333 * B. 10920 D. 7260

210. Big chain sprocket wheels are designed with spokes/arms are generally elliptical in cross section with major axis _______times the minor axis A. 2 * C. 1 B. 2 D. 3

211. For acceptable ideal range of tightness which may result from the

application of specific combination of allowances and tolerances. A. allowance limit C. interference B. tolerance limit D. Fit *

212. Determine the safe wall thickness of a 30 inches steel tank with

internal pressure of 7.82 MPa. The yield stress of material is at 275.48 MPa. The factor of safety to use is 2.0. A. inch C. 21.6 mm * B. 232.6 cm D. 5/8 inch

213. The recommended center distance of sprockets should not be less

than _________ times the diameter of bigger sprocket A. 1.75 C. 1 * B. 2 D. 2

214. An occupant moves toward the center of a merry go around at 6

meters/sec. If the merry go round rotates at 6 rev./min. Compute the acceleration component of the occupant normal to the radius A. 6.79 C. 7.54 * B. 8.29 D. 6.11

215. The absolute viscosity of the fluid divided by its density expressed

in same term of units is also called_________ A. centistokes C. Petroffs equation B. kinematic viscosity * D. light petroleum oil

216. Find the tooth thickness on the tooth circle of a 20 degree full

depth in volute tooth having a diametral pitch of 3, circular pitch of 1.0472 and whole depth of tooth at 0.60. A. 10.7 mm C. 10.1 mm B. 13.2 mm * D. 7.9 mm

217. It is required that pipes bigger than ________mm. should not be

screwed but flanged A. 76.2 C. 2 inch B. 63.5 * D. 68.5

218. An eyebolt is lifting a block weighing 350 lbs. The eyebolt is of

SAE C 1040 material with Su = 67 ksi and S2 = 55 ksi what is the stress area (in inches square) of the bolt if it is under the unified coarse series thread? A. 1341 C. 0991 B. 0.1134 * D. 1043

219. Formed by the intersection of the adjacent flanks of adjacent

threads when extended is called. A. crest apex C. sharp root * B. all of these D. sharp crest

220. In designing the spoke or wheel arm of a flywheel it is ideal to

consider that the cross-sectional area of the spoke at rim side should not be less than ________of the cross area at the hub side A. 80% C. 90% B. 2/3 * D. 3/8

221. Find the number of active coils of a No. 8 wire Helical Spring with

index of 6, steady load with spring rate of 42.5 lb/in . Maximum allowable stress is 60 ksi A. 25 * C. 29 B. 28 D. 22

222. The cutting up to 70% is best for drilling extremely hard metals

and for soft materials ______degrees may be applied A. 60 C. 40 * B. 45 D. 48

223. _________is the process necessary to reduce the brittleness in

alloy steel A. martempering C. normalizing B. carburizing D. tempering *

224. The total machinery weight plus the foundation weight should be

well distributed in the corresponding soil area which is enough to


8

cause a bearing stress within the safe bearing capacity of the soil with a factor of safety of_________ A. 4.5 C. 4.2 B. 3 D. 5.0 *

225. The total weight of 2 steel plates size x 3 x 20 ft is

A. 1838 lbs * C. 3676 lbs. B. 1698 lbs. D. 1848 lbs.

226. Steel springs are made of high carbon steel heat treated and/or

cold worked to a high elastic limit to get good elastic deflection. In general the carbon content is at _________. A. 0.40% or more C. 0.5% or more * B. 0.65% or more D. 0.66% or more

227. In a chain drive design for large speed reduction it is preferable to

use a double reduction or compound type of transmission instead of single two sprockets transmission. Drives should type be so designed that the angle between two tight chain strand does not exceed_____degrees. A. 45 * C. 55 B. 60 D.90

228. Method of finishing/shaping a machine part of exceptionally high

carbon or high chromium steel parts (orveryhard material) A. using oxygen lanching B. using abrasive grinding * C. machining using carbine insert D. machining using high speed tool steel

229. Alloy steel used in manufacturing bolts studs tubings subjected to

torsional stresses A. AISI 3141 C. AISI4830 B. AISI 2330 * D. AISI 4310

230. Which of the following is not a viscoelastic material?

A. Teflon C. all of these B. plastic D. metal *

231. A resulting force that replace two or more forces acting together

A. vector C. resultant * B. couple D. equilibrant

232. Stress relieving is also_________for the purpose of reducing the

internal stresses of steel material/metal A. tempering * C. all of these B. normalizing D. annealing

233. Matensite (stainless steel) contains 4 to 26% Cr. And a maximum

of ______% nickel A. 2.5 * C. 3.5 B. 3.25 D. 2.0

234. Compute the deflection of a 18 coils helical soring having a load of

100 kgs. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9 256 cm and with diameter of 9 525 mm. The spring is square and ground ends. A. 9 mm C. 112 mm B. 101 mm * D. 14 mm

235. A flanged bolt coupling has ten (10) steel 25.4 mm diameter bolts

evenly tighten around a 415 mm bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 50 MN/m2 A. 59.95 KN-m C. 46.15 KN-m B. 52.6 KN-m * D. 43.8 KN-m

236. The material that can cut/wear hardest substance subjected to:

A. carbide C. tungsten B. abrasive * D. vanadium

237. A ridge of uniform section in the form of a helix cut around the

circumference of a cylinder and advancing along the axis A. thread roots C. screw threads * B. helix thread D. chamfers

238. Cast iron flywheels are commonly designed with factor of safety of

A. 10 to 13 * C. 10 to 14 B. 10 to 12 D. 8 to 13

239. Class of material exhibiting decreased electrical conductivity with

increasing temperature A. aluminum C. metals * B. p-type semiconductors D. n-type semiconductors

240. The welding made along the edges of two parallel plates is called

______ A. groove joint C. edge joint * B. fillet joint D. corner joint

241. Not part and in fact should not be used in the steel melting

process A. coke * C. zinc B. silicon D. aluminum

242. Rule of thumb in calculating the Equipment foundation mass

should be____times the weight of the machinery it is supposed to support A. 3-5 * C. 3-9 B. 3-6 D. 2-4

243. The strength of non-ferrous alloys is at maximum at room

temperature while that of ferrous metal has a maximum strength

at_______ F A. 400 * C. 450 B. 1200 D. 350

244. A 76.2 mm diameter shafting of SAE 1040 grade cold rolled,

having a yield point of 50 ksi and with a x x 5 inches key. Compute the minimum yield point in the key in order to transmit the torque of the shaft. The factor of safety to used is 2 and Sys=0.5Sy. A. 39.120 Ksi C. 279.20 Ksi B. 42.130 Ksi D. 47.120 Ksi *

245. The ratio of stress acting on an elastic substance to the decrease

in volume per unit volume A. bulk modulus * C. elastic limit B. modules of resilience D. modules of elasticity

246. The normal helix angles in helical gear is recommended in the

range of ______degrees. A. less than 18 C. 15 to 25 * B. 20 to 35 D. 20 to 30

247. Type of bolt commonly used in the construction that is threaded in

both ends A. stud bolt * C. hex bolt B. acne threaded bolts D. square threaded bolts

248. It is rigid piece which serves to transmit force from a piece

another piece or to cause/ control motion A. follower C. cam motion B. crank D. link *

249. A 20 kgs. cast iron piece rest on a plain horizontal aluminum

surface. To move the object it needs a force of 7 lbs. The density of AI is 0.098 lb/in3 and iron is 0.260 lb/in3 A. 0.172 C. 1.601 B. 0.186 D. 0.160 *

250. Iron based alloy containing 9-16% chromium

A. Mn Hadfield steel C. stainless steel * B. chrome-moly steel D. high chrome steel

251. Shafting up to 3 inches in diameter is usually made from cold

rolled steel and the common biggest diameter of cold rolled steel is____ A. 4 inches C. 6 inches B. 6 7/8 inches D. 5 inches *

252. It is ideal for maximum quietness in sprockets drive operation to

choose _____ or more teeth A. 24 C. 27 * B. 18 D. 21

253. All associated with standard material specification except

A. American Iron and Steel Institute B. Society of Automotive Engineers C. Southeast Asia Iron and Steel Institute * D. American Society for Testing Materials

254. For stable equipment foundation the total combined engine driven

equipment and foundation center of gravity must be kept below the foundations too that usually about______ times the usual total combined weight of the machinery it is supposed to support. A 3 to 4 C. 2 to 4 B. 3 to 7 D. 3 to 5 *

255. A triple thread worm has a pitch diameter of 3 inches. The wheel

has 25 teeth and a pitch diameter of 5 inches. Material for both the worm and the wheel is of phosphor bronze. Compute the helix angle (Tan ) A. 0.20 * C. 0.40 B. 0.30 D. 14


9

256. A cylinder tank with 10 inside diameter contains oxygen gas at 2500 psi. Calculate the required wall thickness in (mm) under stress of 28 000 psi A. 11.34 mm * C. 12.44 mm B. 10.24 mm D. 10.54 mm

257. The process of peening the joint portion immediately after the

welding greatly improves the fusion structures avoids possible cracking, avoids possible distortion etc. Peening can also _______process at the same time A. tempering * C. normalizing B. martampering D. annealing

258. The distance between rivet center nearest each other in adjacent

rows is called ______ A. pitch C. margin B. back pitch D. diagonal pitch *

259. A major alloy in tool steel

A. Cr * C. Cobalt B. Fen D. Mn

260. A rule of thumb the speed limit of flywheel rim speed should be

6000 fpm for cast iron material and for cast steel flywheel rim at _______ meters/min A. 3050 C. 7000 B. 4500 D. 10000 *

261. Should two equal and opposite collinear forces is added to the

forces already in equilibrium, which of the following statement is true? A. Unbalanced moment is maintained B. Equilibrium is maintained * C. Equilibrium is disturbed D. it creates an unbalanced situation

262. A pair of gear with gear ratio of 3 and 60 gear teeth of 14

degree full depth tooth. The diametral pitch is 10. Compute the tooth thickness on the pitch circle A. 0.570 inch C. 0.157 inch * B. 0.352 inch D. 0.142 inch

263. __________ addition imparts resistance to atmospheric corrosion

in steel etc. A. aluminum bronze C. copper * B. manganese D. bronze

264. The width of a tooth space exceeds the thickness of each of the

engaging tooth on the pitch circle________ A. allowance C. top land B. bottom land D. backlash *

265. Distance measured perpendicular to the axis between the crest of

the thread and the root of its mating thread in a thread assembly of screws A. tolerance class C. crest clearance * B. crest truncation D. tolerance limit

266. Percentage of cut on the return stroke of hacksaw blade

is________ A. 21 C. 1 % B. 3 % D. 0 % *

267. Compute the angle required in degrees, for the road to be slanted

to prevent an automobile travelling at 25 m/s from tending to slip. The radius of curvature is 200 m. A. 21 C. 18 B. 14 D. 16

268. __________is also called strain hardening

A. work hardening * C. annealing B. quenching D. normalizing

269. Imaginary formed by the intersection of the flanks of a thread

when extended is called_______ A. Sharp Crest C. Root apex B. Sharp root D. All of these

270. Compute the maximum deflection of a 20 coils helical spring

having a load of 75 kgs. The spring is a square/ground ends with modulus of elasticity in shear of 79.84 GPa outside diameter of 101.6 mm wire diameter of a 9 525 mm A. 140.7 mm C. 15.17 mm B. 112.7 mm D. 126.7 mm *

271. _______forces means when their lines of action can be extended

to meet to one point A. concurrent * C. collinear B. centroids D. resultants

272. The welded joints permit placing the added metal exactly where

needed and produce an integral structure which can develop_____% efficiency on any thickness of section specially for mild steel materials A. 95% C. 100% * B. 85% D. 90%

273. A keyed sprocket deliver a torque of 778 8 Nm thru the shaft of

54 mm OD . The key thickness is 1. 5875 cm and the width is 1.11 cm compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension A. 39.12 cm C. 52.22 cm B. 4.82 cm D. 4.32 cm *

274. Compute the cutting speed in fpm of a workpiece with 2 inches

diameter and running at 100 rpm? A. 72 C. 62 B. 102 D. 52 *

275. One horsepower is equal to_____________

A. 556 ft.lb/sec C. 746 joules/sec * B. 748 Nm/sec D. 42.4 BTU/min.

276. Compute the diameter of a solid shaft transmitting 75 Hp at 1800

rpm. The nature of the load and the type of service is such that the allowable Ss based on pure torsion is 6000 psi A. 1 7/8 C. 1 5/16 * B. 2 1/16 D. 3 1/8

277. Compute the safe wall thickness of a 76.2 cm diameter steel tank.

The tank is subjected to 7.33 MPa pressure and the steel material has yield stress of 215.4 MPa. The factor of safety to use is 3 A. 1 inches C. 4.09 cm B. 3.89 cm * D. 3.69 cm

278. A foot rule has how many 1/8?

A. 96 * C. 120 B. 48 D. 108

279. An elevator weighing 2000 lbs. is moving vertically upward with an

acceleration of 3 ft./sec2. A man standing in said elevator weighs 180 lbs. Compute the tension in the supporting cable under this condition A. 2180 lbs C. 1820 lbs B. 2191 lbs D. 2366 lbs *

280. A watt is equivalent to _________

A. 42.4 BTU/min. C. 44.20 ft.lb/min. B. 1 Nm/sec * D. all of these

281. 50% of is

A. 1/100 C. 25 B. 0.25 * D. 001

282. The capsule orbits of the earth 180 km above the surface. In what

velocity in m/s necessary for a circular orbit condenser the earth radius at 6400-km and at 9.2 m/sec2? A. 8864 C. 7780 * B. 7016 D. 8058

283. A small countershaft is 1 1/2 inch in diameter and has an

allowable stress of 8500 psi. Find the horsepower delivered by the shaft at a speed of 125.7 rad/sec. A. 720 C. 13.31 * B. 1.4 D. 14.72

284. A wheel accelerates from rest with a = 5 radian/sec-sec. Compute

how many revolutions made in 4 seconds? A. 5.71 rev C. 7.00 rev B. 6.36 rev * D. 20.00 rev

285. The shaft is subjected to a steady load of 36,000 in lb. at a shear

stress of 10,000 psi. Compute the diameter of the said shaft in inches A. 1 7/8 C. 3 * B. 2 D. 2

286. What minimum distance can a truck side on a horizontal asphalt

road if it is travelling 25 m/s? The coefficient of sliding friction between asphalt and rubber tire is at 0.6. the weight of the truck is 8500 kg. A. 44.9 C. 53.2 * B. 58.5 D. 63.8

287. A Keyed gears deliver a torque of 912.4 Nm thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 find the length of the key. Assume the


10

permissible stress values of 61.2 MPa for shear and tension at 99.8 MPa. A. 47.42 mm C. 42.22 mm * B. 39.72 mm D. 46.92 mm

288. A band brake is to absorb 5 Hp at 200 rpm. The maximum

pressure of the lining and drum is 120 psi. the angle of wrap is 3.6 radians the width of the band is 3 inches and f = 0 15. Find the forces at the tight side. The diameter of the drum is at 8 inches A. 2680 lbs C. 3880 lbs B. 2880 lbs * D. 2980 lbs.

289. A liquid full bucket is to be rotated in the vertical plane. What

minimum angular velocity in radian/sec is needed to keep the liquid no spilling out if the rotating arm is 1.2 meters A. 2.26 C. 3.10 B. 25.6 D. 2.86 *

290. Compute the speed a satellite must have to orbit the earth at an

elevation of 100 km. Earths radius is at 6400 km. Assume no change of gravity with the elevation A. 6320 m/s C. 8740 m/s2 B. 7120 m/s D. 7920 m/s *

291. A 16 ft steel lineshaft has no bending action except its own

weight. What power in Hp can the shaft deliver at a speed of 200 rpm. Consider that the torsional deflection will not exceed 0.008/ft of length A. 13.2 C. 24.4 B. 15.8 D. 14.6 *

292. The torsional deformation of a SAE 1040 steel shaft is to 0.8 in a length of meter. The shear stress is 69 Mpa . Compute the diameter of the shaft in millimeter. Steel modulus of elasticity is 79,300 Mpa or N/mm2

A. 51 C. 75 B. 50 D. 62 *

293. Compute how many 3/8 inch diameter set screws required to

transmit 3 Hp at a shaft speed of 1000 rpm. The shaft diameter is 1 inch A. 1 C. 3 B. 2 * D. 1

294. A pair of gear/pinion of 42 tooth and 18 tooth with a diametral

pitch of 0.7874 teeth/cm and the addendum is 0.8/p and

dedendum 1/p. The gear pressure angle of 20 . Compute the center distance of the pair of gears in meters A. 0.5026 m C. 0.3516 m B. 0.3426 m D. 0.4013 m *

295. Determine the width of a 6 ply rubber belt required for a

ventilating fan running at 150 rpm driven from a 12 inch pulley on a 70 Hp at 800 rpm. The center distance between pulley is 12 ft. and the rated belt tension is 78.0 lb/in width A. 12 * C. 10 B. 8 D. 15

296. Compute for the torsional deflection in degrees of a 110 mm

diameter, 1.4 m long shaft subjected to a twisting moment of 3 x 106 N-mm. The torsional modulus of elasticity is 83000 N/mm2 A. 0.27 C. 0.20 * B. 0.31 d. 0.24

297. Find the torsional moment (in Newton-mm ) developed when the

shaft delivers 20 kw at 200 rpm A. 0.85 x 106 C. 1.20 x 106 B. 1.0 x 106 * D. 2.10 x 106

298. Determine the load in kN on a 25 mm diameter 1200 mm long

steel shaft if its maximum elongation exceeds 1mm A. 83 * C. 103 B. 125 D. 93

299. Find the thickness of a metal needed in the semi-spherical end of a cylinder vessel 0.70 meter in diameter subjected to an internal pressure of 2.7 N/mm2. the material is mild carbon steel and tensile stress is 69 N/mm2. A. 5.2 mm C. 7.53 mm B. 6.02 D. 6.84 mm *

300. A 102 mm diameter shaft is driven at 3000 rpm by a 300 Hp prime

mover. The shaft drives a 121.9 cm diameter chain sprocket having 85% output efficiency. Compute the torque in in-lb developed in the shaft A. 5,6000 C. 8,150 B. 7,100 D. 6,300 *

301. Determine the average time to cut by automatic oxy-acetylene (machine) crosswise a 4ft. x 8 ft x 4 in thick steel plate. A. 6.85 min. C. 10 min B. 318 sec D. 360 sec *

302. Compute for the induced/compressive stress, in kPa, of a steel

solid shafting of 50 mm diameter and 800 mm in length that is subjected to an increase of temperature by 80 deg C A. 181,816 C. 218,182 B. 242,816 D. 196,560 *

303. A mass weighing 56 lbs. rests on a horizontal surface. The force

needed to move along the surface is 20 lbs. determine the coefficient of friction A. 0.0 C. 0.36 * B. 0.112 D. 0.28

304. Determine the time in seconds, to saw a rectangular magnesium

bar 5 in. wide and 2 in. thick if the length of cut is 5 in. The power hacksaw does 120 strokes/min and the feed/stroke is 0.127 mm A. 189 C. 99 B. 500 * D. 20

305. A car travels with an initial velocity of 10 m/sec or 36 km/hr. If it

is decelerating at rate of 3 m/sec-sec, how far in meters does it travel before stopping? A. 17 * C. 19 B. 21 D. 15

306. Compute for the twisting moment in in-lb developed when the

shaft delivers 20Hp at 1200 rpm A. 1166 C. 1050 * B. 915 D. 945

307. In an Oxy-Acetylene manual welding method to weld a 3 ft.

long seam in a 0.375 thick steel plate at a consumption rate of 9 ft3/ft for oxygen and 7 ft3/ ft for acetylene. Compute for the total combined gas consumption in ft3 A. 48 C. 56 * B. 24.5 D. 31.5

308. A cylinder tank with 10 inches inside diameter contains oxygen

gas at 2500 psi. Calculate the required wall thickness in millimeter under stress of 28000 psi A. 10.54 C. 10.24 B. 11.34 * D. 12.24

309. Compute for the load in kN on a 3 cm diameter, 100 cm long steel

rod if its maximum elongation exceed 0.12 cm A. 178 * C. 148 B. 196 D. 287

310. A baseball is thrown straight upward with a velocity of 20 m/s .

Compute for the time elapsed for the baseball to return. Assume for a zero drag. A. 1.84 C. 2.50 B. 2.2 D. 2.04 *

311. Compute for the polar section modulus of an SAE 1060 shafting

having a diameter of 3 inches. Use a factor of safety of 2 and design stress at 8000 psi A. 4.7 C. 4.2 B. 6.1 D. 5.3 *

312. Find the torsional deflection, in degrees of a solid steel shaft 110

mm OD 1.4 m long subjected to 3.1 x 106 N-mm. The torsional modulus of elasticity is 80,000 N/mm-mm A. 0.22 * C. 0.28 B. 0.195 D. 0.24

313. A short shaft transmits 200 hp at 300 rpm. Determine the

diameter of the shaft in inches. A. 5 C. 4 B. 2 D. 3 *

314. Forces not on the same plane are called

A. Component C. Non-coplanar * B. Resolution D. Composition of forces

315. The distance between the center of oscillation and the point of

suspension is called____ A. center of percussion C. radius of oscillation * B. center of gravity D. Fix axis

316. If the velocity is variable and regularly/constantly increasing the

rate of change is called____ A. Moment C. Constant work B. Motion D. Acceleration *


11

317. ______is a kinematic chain in which one link is considered fixed for the purpose of analysis but motion is possible in other links A. Sprocket chain C. Mechanism B. Belting D. Frame *

318. __________is one of the rigid members/bodies joined together to

form a kinematic chain A. All of these C. Frame B. Link * D. Coplanar

319. The resultant of a pair of equal forces but opposite in direction is

called______ A. Non-concurrent C. Resultant B. Concurrent D. Couple *

320. The helical and herringbone gear teeth cut after heat treatment

should have a hardness in the range of 210/300 BHN. The pinion gear teeth hardness, on the other hand ideally/normally should be at______BHN A. 250/320 C. 400 B. 350/380 D. 340/350 *

321. As a rule the center to center distance between sprocket should

not be less than____ times the diameter of the bigger sprocket and not less than 30 times the pitch nor more than about 50 times to pitch A. 2.5 C. 3 B. 2 D. 1.5 *

322. A single forces which produces the same effect upon a mass as

two or several forces acting together is called______ A. components C. composition of forces B. resultant * D. resolution of forces

323. All forces in the same plane are called______

A. Parallel C. Couple B. Coplanar * D. Resultant

324. The forces of attraction between two bodies is directly

proportional to the product of their masses and inversely proportional to distance square between their centers. This law is ________ A. Law of motion C. Newtons law B. Law of gravitation * D. Hooks law

325. Gears are manufactured usually in the following processes:

milling, generating, shaving, grinding and ___which is also used. A. Blanking * C. Molding B. Heat treatment D. Dinking

326. Any object thrown upward will return to earth with the magnitude

of the terminal velocity equal to A. 50% of the initial velocityC. About 90% of the initial velocity B. 80% of the initially velocity D. the initial velocity *

327. Flat belt that is too tight will induce strain on the bearing and

belt________ A. result to uneconomical operation C. life will be shortened * B. suffer/shafter D. will be sheared/cut

328. The resulting cross-sectional area of the tensile test specimen

divided by the specimen original area is called________ A. % elongation * C. charpy test B. impact test D. izod test

329. SAE 51xxx belongs to the________ steel family

A. chromium * C. Manganese B. Carbon D. Nickel

330. In itself, it is a lubricant and usually one of the important elements

in casting non-ferrous metals like bronze, for example A. Antimony C. Zinc B. Lead * D. Babbit

331. Gasket material which should avoid hot liquid/steam application.

A. Asbestos fiber C. Wool B. Rubberized * D. Nylon fiber

332. The same material properties all over/direction and at any

particular point in a structural member is_____ A. Isentropic C. Isotropic * B. Homogenous D. All of these

333. Arc produced by two tungsten electrodes into which a jet of

hydrogen is directed A. Hydrogen lancing C. Electro-beam welding B. All of these D. Atomic hydrogen welding *

334. What is the carbon content range of SAE 4140 chrome-Moly steel after heat treatment? A. 0.30/0.45 C. 0.30/0.50 B. 0.38/0.45 D. 0.38/0.43 *

335. Actual torque ratio of a gear set divided by its gear ratio

A. clearance C. efficiency * B. contact ratio D. approach ratio

336. A low coefficient of expansion, corrosion resistant weak in

strength and used for non-ferrous application as an alloying element A. Aluminum * C. copper B. copper oxide D. aluminum oxide

337. For better mounting of bearing it is preferred to heat the inner

ring the range of 200 F and___ but never more than______ F as overheating might reduce the ring hardness A. 280 C. 300 B. 250 * D. 320

338. For large speed ratio and large sprocket utilized it is recommended

cast_______ material since the large sprocket teeth are having fewer engagement. A. alloyed steel C. malleable iron B. iron * D. heat treated steel

339. Roller bearing is utilized on_______ carrying capacity

and is better than ball bearing in this condition A. high temperature load C. low load B. heavy load * D. reversing load

340. To enhance mechanical properties, fabrication characteristic or

any other attributes of steel, some elements are added in melting in specific ranges or minimum aside from carbon and generally termed____ A. Bessemer steel C. AISI steel B. Alloy steel * D. SAE steel

341. Materials having thermal expansion of about 10 times higher than

those of metals and has more heat generated during machining is____? A. Aluminum C. Asbestos B. Plastic * D. PVC

342. To hold to minimum the axial direction of deflection/movement, a

separate thrust bearing or pre-loaded bearing capable of absorbing considerable load is required. The type of bearing to use is a_____bearing A. Double row angular contact * C. Tapered roller bearing B. Wide type self-aligning D. Deep groove ball

343. Pulley made of ______ordinarily is 45 to 55% less in weight and

2.35 to 2.70% less slippage compared with______pulley A. wood/iron C. steel/iron * B. iron/steel D. wood/steel

344. To avoid scoring in the bearing surface and the shaft due to

contamination/absorption of the fine dirt in the bearing during operation/lubrication, the bearing material to apply should have good _____properties A. corrosion resistance confermabilityC. embeddability * B. corrosion resistance D. anti-scoring

345. What do impact tests measure?

A. plasticity C. ductility B. toughness * D. compactness

346. Corresponding piping color for alkaline

A. red C. green B. violet * D. blue

347. Type of gear that transmits power at an angle

A. bevel* C. spur B. herringbone D. helix

348. Which of the following gasket material is not used for high

temperature steam? A. wool C. plastic nylon B. asbestos D. rubberized *

349. A plane perpendicular to the gear axis.

A. pitch plane C. plane of rotation * B. normal plane D. radius of gyration

350. Specification of molybdenum alloy

A. SAE 3xxx C. SAE 5xxx B. SAE 4xxx * D. SAE 6xxx

End


12

machine design elements

Documents