1

2

Operation viaClient SoftwareTestingPowering OnWiring

Network

Security Control Panel

with Bus Extension Module

Quick Start Guide

Connect the keypad, alarm output, trigger, and power cables,with following the figure below. Power down the control panelbefore connecting and disconnecting accessories and peripherals.

Step 1 Wiring

The keypad registration will be completed in 1 minute after the control panel being power on. The system then will complete the start-up and enter the properly status of working in 20 seconds.While the registration is succeeded, the working status indicator of LED keypad will turn green.The display demonstration of LCD keypad after powering on is shown below.

HIKVISION 20XX.XX.XX XX:XX:XXVX.X.X build XXXXXX

Step2 Powering On

Dry Contact Dry Contact Dry Contact Dry Contact

2.2KΩNC

C

Z

G

Peripheral Security Detector

NC Detector

2.2KΩ

NO

C

Z

G

Security Control PanelSecurity Control Panel Security Control Panel

NO Detector

Peripheral Security Detector

Zone

Zone

Alarm Output

KeypadPower Supply

G Z4 G Z6Z5 G Z8Z7GZ1 Z2 Z3

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

NO/NC1COM1 COM2 COM3 COM

NO/NC2 NO/NC3 NO/NC4

G Z4 G Z6Z5 G Z8Z7GZ1 Z2 Z3

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

TX RX G

PrinterDry Contact Dry Contact Dry Contact Dry Contact

D + +D G12V -

Keypad

DC_IN +GBAT

_ +12V G+12V G

14.3V DCPower

12VDC 7AHLead-acid

AlarmBell

Auxiliary Power

Interface

BELL AUX

Network Data Indicator

14.3 Power Indicator

Reset

TAMPER1

BELL AUX

FUSEKEYPAD Network Status Indicator

Working Indicator

3.3V Power Indicator

G Z10Z9

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

G Z12Z11

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

G Z14Z13

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

G Z16Z15

N.O N.O

2.2K EOL

2.2KEOL

N.C N.C

Z9 to Z16 are only supported by the network security control panel with 16 zones.

Power Indicator

Telephone Module

HandsetIncom

ingPhone Line GPRS Module

DC

Unoccupied Zone

NO/NC1COM1 COM2 COM3 COM

NO/NC2 NO/NC3 NO/NC4

The resistance of 2.2KΩsupports tamper-proof and non-tamper-proof wiring. The resistance of3.3KΩ, 5.6KΩor 8.2KΩ only supports non-tamper-proof wiring.

BUS1- BUS2- BUS2+BUS1+ GG

M-BUS 1 M-BUS 2

5V Power Indicator

Bus Power Indicator

13.8V Power Indicator

15V,-24V Power Indicator

M-BUS Module

UD07394B

3 4 Step4 Operation via Client Software

Arm/Disarm

Clear Alarm

Test

Activate Device11

22

Add Device

3

Path: Device Management -> Server -> Online

Note: You should activate the device for the first usage.

Path: Device Management -> Server -> Add DeviceInput the device nickname, IP address, user name, and password, and click Add.Default Port No：8000Default Username：admin

For more, please refer to Security Control Panel Installation Guide.

For more, please refer to Video Security Control Panel User Manual.

If the system is working properly, the keypad alarm will

be occurred while triggering the zone.

The alarm Indicator are shown below.

LED Keypad：Channel indicator turns flicking red.

LCD Keypad：Keypad screen display alarm

information.

If the system is working properly, the

arming/disarming operation will take effect.

Enter the command above for disarming when the

system is in the arming status.

Quick Start GuideCOPYRIGHT ©2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED.Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.About this Manual This manual is applicable to video security control panel.The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals.Trademarks Acknowledgement and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.Legal DisclaimerTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS

Step3 Testing

Arming/Disarming Command： 【User Password】+ #

Buzzer：Rapid beep sound.

Enter the command below to clear the triggered alarm.【User Password】+【*】+【1】+【#】

Online Device (2)

Add to Client

IP

xx.xx.xx.xx

xx.xx.xx.xx

xxxxxxxxxxxxx

xxxxxxxxxxxxx

xxxxxxxxxxxxx

xxxxxxxxxxxxx

xxxx-xx-xx xx:xx:xx

xxxx-xx-xx xx:xx:xx

8000

8000

Inactive

Active

Device Type Firmware Version Server PortSecurity Start Time

Add all Modify Netinfo Reset Password Activate Filter

Refresh Every 60s

Onlie Device (2)

Add to Client

IP

xx.xx.xx.xx

xx.xx.xx.xx

xxxxxxxxxxxxx

xxxxxxxxxxxxx

xxxxxxxxxxxxx

xxxxxxxxxxxxx

xxxx-xx-xx xx:xx:xx

xxxx-xx-xx xx:xx:xx

8000

8000

Inactive

Active

Device Type Firmware Version Server PortSecurity Start Time

Add All Modify Netinfo Reset Password Activate Filter

Refresh Every 60s

Add Device Modify

Nickname IP

Add

Adding Mode:

Add Offline Device

Nickname:

Address:

Port:

User Name:

Password:

Add Cancel

Export to Group

Set the device name as the group name and add all the channels connected to the device to the group.

IP/Domain IP Segment IP Server HiDDNS

Function Description Command

Programming/ Editing Password

Control Panel Programming

【Installer Password】【*】【0】【#】

Exit Operation 【*】【#】 Operator Password 【Operator Password】【*】【0】【#】

【User No. (3digits)】【#】 【New Password】【#】 【New Password】【#】

Testing Testing 【Password】【*】【6】【0】【#】 Alarm Center Testing 【Password】【*】【6】【1】【#】 Project Mode 【Password】【Project】【9】【0】【n】【#】 Exiting Project Mode 【Project】 or 【*】【#】

Arming/Disarming Normal(Away)Arming/Disarming

【Password】【#】

Instant Arming 【Password】【*】【7】【#】 Stay Arming 【Password】【*】【4】【#】

Function Description Command

Clearing Alarm Clearing Under arming status

【Password】【*】【1】【#】

Bypass Bypass Zone（n） 【Password】【Bypass】【n】【n】【n】【#】

【Password】【Bypass】【n】【n】【n】【#】

【Bypass】【n】【n】【n】【#】

nnn is the zone No.

Keypad Settings Enabling/Disabling Keypad Tone

【*】【5】【1】【#】

Enabling/Disabling Fault Prompt

【*】【5】【6】【#】

LCD Backlight Control 【*】【5】【2】【n】【n】【n】【#】 LCD Backlight Disabling

【*】【8】【#】

Restore Bypass:Enter Command Under the bypass Status

Normally Used Keypad Operation Command

Siren (Connected)：Triggered.