ltc 2600 series multiplexer quick reference...

Also Used by Video Controller

LT C 2 6 0 0 S e r i e s M u l t i p l e x e r Q u i c k R e f e r e n c e G u i d e

System4

I n s t a l l a t i o n I n s t r u c t i o n sThese features are available on System4 Series only.Keyboard: (LTC 2601/00 and LTC 2602/00 models only). Connect a remote keyboard with Pan/Tilt/Zoom for control and programming.Console: Connect a host computer for CCL command inputs, or a Bosch LTC 2650 Graphical User Interface, or a printer.SDA: Five biphase outputs for a Bosch AutoDome® or Receiver/Driver.

Connect cameras (up to 16) to camera BNC inputs.

Follow steps 1-8 for quick installation

If looping is required,connect camera out to

second source (second BNC).

Connect a monitor to MON A output for multiscreen display and tape playback.

Connect a monitor to MON B output if needed.

NOTE: For System4 Triplex Series only, MON B can display a quad

or a multiscreen picture when operating in live or playback mode.

For playback, connect the Output of the VCR to VCR

IN on the multiplexer.

For recording, connect the Input of the VCR to the

VCR OUT on the multiplexer.

Synchronize the Mux with the VCR byconnecting pin 21 (VEXT INPUT 1)to VCR Clock Out on your recorder.

Connect pin 25 to VCR ground.

For 6-Channel LTC 2622, refer to theInstruction Manual

Apply power to the unit. The Console, SDA, KB, SVHS,and Fonts are available with

System4 Series only. Refer to theInstruction Manual for details.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 2 3 4 5 87Pin 25 Pin 21

7 5 4 3

1

2

8

6

O p e r a t i n g I n s t r u c t i o n s

Display Modes Available For LTC 2600 Series Multiplexers

Full Screen Display: Shows one camera, full screen on one monitor.Press FULL SCREEN on the front panel, then press the appropriatecamera number.

Quad Screen Display: Divides the screen into four viewing areas.Press QUAD once to enable the feature. Press QUAD repeatedly to toggle through the viewing configurations (three times for the 9-Channel model; four times for the 16-Channel model; eight timesfor System4 models). Press ALT , then SEQ to sequence throughall quad screens.

Multiscreen Display: Enabling this feature shows one of fivemultiscreen configurations: 4x4 (16 cameos), 12+1, 8+2, 3x3, and4+3. Press MULTI repeatedly to toggle through the selections.

Cameo Mode: When in MULTI or QUAD mode, the screen area where a camera is displayed is called a cameo. Note that thenumbered front panel keys can refer to either cameras or cameos.Press CAMEO to toggle the operation of these keys to the cameofunction (the CAMEO LED is illuminated when the multiplexer is incameo mode). Press CAMEO again to revert to the camera function.

Assign a Camera to the Cameo

1) In MULTI or QUAD display mode, press the desired camera key, and then pressCAMEO. The cameo selected will display a flashing camera title. Select the desiredcamera, and the cameo will display the selected camera.

Press CAMEO to store and/or exit.

2) Press ALT and SELECT (the ALT LED will flash). Cameo #1 will be selectedand will show a flashing camera title. Press the desired camera key. Cameo #1 willdisplay the selected camera, and cameo #2 is automatically selected. Repeat thisprocedure for the remaining cameras.

Press ALT to exit at any time.

Recording Live Pictures

Press the green ALT key, and then press RECORD. Thiskey combination toggles the record mode on and off.For System4 LTC 2672 or LTC 2682 Series:To activateboth VCR outputs, press ALT, then 2, then RECORD.

Playback

To playback the recorded pictures, press the green ALTkey, and then press PLAY. For Simplex models, Record mode must be turned OFF.

Advanced Functions

Zoom: Enables the active camera display (a cameo in MULTIor QUAD display) to be digitally enlarged by a factor of 2:1.Zoom will be displayed on the monitor screen. Use the arrowkeys for closer inspection of any part of the selected image.

Freeze: Holds the selected camera picture on either full screenor cameo. Press FREEZE again to release the image from thisfunction. Changing the display screen mode releases the freezemode from all cameos.

Alarms and Actions Acknowledge:When an alarm or action condition occurs, the action alarmcamera picture displays full screen on Monitor B, and the ALM or ACT LED flashes. ALARM/ACTION will also flash on Monitor A. Clearing an Alarm/Action by pressing ACT or ALM will stop any recording associated with thatfunction. The method of clearing alarms or action conditionsdepends on the model of your multiplexer.

Refer to the Instruction Manual for advanced operationfeatures.

REC

PLAY

Access the menu screens by pressingALT (Green) followed byMENU . The menus (as shown above) will be displayed on Monitor A.

The Main Menu (shown above)displays two setup options: QuickSetup and Advanced Setup. In mostcases, the Quick Setup provides allprogramming necessary for systemoperation.

To choose the option, press SELECT .

The Quick Setup program includesTime/Date, AutoSet, and VCRSetup. For further information,consultthe built-in HELP feature by pressingALT.

Select Time/Date. Enter the timeformat (12 or 24 hours), time, dateformat (dd/mm/yyyy;yyyy/mm/dd),and date information as requested. Usethe direction (arrow) keys to move thecursor and scroll through menusettings. Press SELECT to choose thesettings, and save your selections.When finished programming alltime/date settings, use ZOOM toreturn to the Quick Setup menu.

Select Autoset and chooseAUTOSET ALL BELOW toautomatically set the record list,sequence, and video loss list (accordingto the number of camera inputsdetected by the multiplexer). Selectingany of the other menu options, will setonly the selected option.

When Autoset is finished, a message isdisplayed for three seconds. Thecamera inputs detected in the setupprocess are also displayed, as shown inthe above sample screen.

Press ZOOM to return to the QuickSetup menu.

NOTE: The LTC 2600 SeriesMultiplexers are configured to recordand playback from a wide variety ofVCRs.

Decide how to synchronize themultiplexer and the VCR. The optionsare (a) Connect and enable the VEXToutput from the VCR (no furtherVCR programming is required), or (b)if VEXT is not available, specify theVCR model and the time-lapse mode.

To program the multiplexer for the VCRin use, select the RECORD SETUPmenu. From the SELECT VCRmenu, press SELECT. Scroll to theappropriate VCR model and pressSELECT.

Press ZOOM to exit. Choose theTIME LAPSE menu and select therecording speed. Press ZOOM fivetimes to exit the programming menu.

The unit is now ready for operation.

P r o g r a m m i n g I n s t r u c t i o n s

MAIN MENUSETUP 1>QUICK SETUP

ADVANCED SETUP

Choose: SELECT More:VExit:ZOOM

QUICK SETUPSETUP 1>TIME/DATE

AUTOSETVCR SETUP


TIME/DATE>TIME FORMAT 12

TIME 12:00:00DATE FORMAT MM/DD/YYYYDATE 01/01/1998


AUTOSETSETUP 1>AUTOSET ALL BELOW

RECORD LISTSEQUENCESVIDEO LOSS LIST


AUTOSETSETUP 101 02 03 04 05 06 -- ---- -- -- -- -- -- -- -- -- --The above cameras were included in selected input lists

HIT ANY KEY TO COMPLETE

VCR SETUPSETUP 1

>RECORD SETUP *VCR OUT*PLAYBACK FORMATRECORD LOCK


RECORD SETUP*VCR OUT* SETUP 1

VEXT INPUT OFFSELECT VCR PHILIPS 3991HDTIME LAPSE 6HD


NOTE: To perform an Advanced Setup for customized system configurations, refer to the instruction manual.

For further information within the menu,consult the built-in HELP feature by pressing ALT

To exit from any menu, press ZOOM to return to the previous screen.

LTC 2601, LTC 2602 ALLPLEX Quick Reference Card Keyboard CommandsNumeric DisplayThe numeric display is a three-digit display that shows the number of the multiplexer that the keyboard is currently controlling. When in the VCR control mode the display shows VCR.

Status DisplayThe status display indicators are located on both sides of the numeric display at the top of the keyboard. On the right side of the numeric display, there are three status display indicators:

Camera , Cameo , Pound . On the left side of the numeric display, there are six status display indicators: VCR , Monitor B , Sequence , Allplex , Record , and Playback . PLAYRECAPXSEQVCR#

Status Display FunctionsCamera LED lit Full Screen selectionCameo LED lit Quad or Multi screen selectionRecord LED lit Recording mode enabledPlay LED lit Playback mode enabledMonB LED lit Mon B is enabledSequencing LED lit Sequencing mode enabledVCR LED lit VCR test mode enabled VCR

SEQ

PLAY

REC

Full Quad Multi Cameo Zoom

Freeze Action Clear Alarm Clear Select Menu

Icon Key BOSCH

View Format and Camera SelectSELECT . . . . . . . . . . . . . . . . . Press Keys

FULL SCREEN . . . . . . . . . . . . Press FULL and then the camera #

QUAD . . . . . . . . . . . . . . . . . . Press QUAD and then press the key

repeatedly to toggle through the different quad

pages: Quad 2, 3. etc.

MULTISCREEN: . . . . . . . . . . . Press MULTI and press the key

repeatedly to toggle through the different

viewing configurations

Multiplexer Command

RECORD (ENCODE) . . . . . . . Press ALT then REC

PLAYBACK (DECODE) . . . . . . Press ALT the PLAY

MON B . . . . . . . . . . . . . . . . . Press ALT then MON B

SEQUENCE . . . . . . . . . . . . . . . Press ALT then SEQ

VCR TEST MODE . . . . . . . . . Press ALT then SEQ

ACTION ACKNOWLEDGE . . . Press ACTION CLEAR

ALARM ACKNOWLEDGE . . . . Press ALARM CLEAR

ZOOM PICTURE . . . . . . . . . . Press ZOOM to enlarge the picture

FREEZE . . . . . . . . . . . . . . . . . Press FREEZE to freeze the picture

MENU SELECTION . . . . . . . . . Press ALT and then MENU

MENU SCROLL . . . . . . . . . . . >, <, ^, and v

ALLPLEX SELECTION . . . . . Allplex + SELECT simultaneously, then #,

then SELECT to select the new Allplex

number. The system accepts only valid Allplex

numbers 1 through 30.

P/T/Z FUNCTIONS . . . . . . . NOTE: Refer to Bosch R/D or AutoDome

Instruction Manual for Auxiliary function

SAVE PRE-POSITION . . . . . . . . Press SET , # (1-99) then SELECT

RECALL PRE-POSITION . . . . . Press SHOT , # (1-99), then SELECT

AUXILIARY ON/OFF . . . . . . . Press AUX + AUX , then #, then

SELECT

VCR CONTROL . . . . . . . . . Note: Only with Bosch RS-232 VCRs

VCR MODE SELECTION . . . . Press VCR + SELECT

simultaneously. LED will display VCR

RECORD . . . . . . . . . . . . . . . . REC

PLAYBACK . . . . . . . . . . . . . . . PLAY

STOP . . . . . . . . . . . . . . . . . . . ZOOM

PAUSE . . . . . . . . . . . . . . . . . FREEZE

FAST FORWARD . . . . . . . . . . CAMEO

FAST REWIND . . . . . . . . . . . . FULL

PLAY

REC

VCR

AUXAUX

SHOT

SET

ALT

VCRALT

SEQALT

ALT

PLAYALT

RECALT

Bosch Security Systems, Inc.850 Greenfield Road Lancaster, PA 17601 USATel: 800-326-3270Fax: 1-717-735-6560www.boschsecuritysystems.com

Bosch Security Systems B.V.P.O. Box 800025600 JB EindhovenThe NetherlandsTele +31 40 27 80000

Bosch Security Systems Pte Ltd.38C Jalan PemimpinSingapore 577180Republic of SingaporeTel: 65 (6) 319 3486

© 2004 Bosch Security Systems GmbH

3935 890 09513 04-26 | Updated June 24, 2004 | Data subject to change without notice.

ltc 2600 series multiplexer quick reference...

Documents