linksys ata pap2

The Linksys PAP2 ATA Device

CommPartners 1 of 15

The Linksys ATA PAP2 Device

The Linksys PAP2 ATA Device………….. 2 The Linksys PAP2 Web Interface………... 3 Adjusting the Codec for Fax……………… 11 Manually Provisioning…………………….. 12 Factory Resetting the Device…………….. 15



Linksys ATA PAP2 Device

Front view of the Linksys ATA Device

Back view of the Linksys ATA Device

Connectivity of the Telephone set into Phone 1 Port on the ATA Device

Connectivity of the Ethernet cable into the ATA Device

Supply power to the ATA Device



Linksys PAP2 Web Interface To access the Linksys web interface, the IP address must be obtained first. The device needs to be connected to the network and powered up.

Lift the handset and perform the following tasks to obtain the IP Address;

Enter **** Enter 110# when prompted The ATA device will read the IP Address back to you. Write down the IP address

From the internet browser address window, type in the IP address.

A window will pop up asking for the user name and password. Enter in “user” as the user name.

To obtain the password, go to the Subscriber Maintenance on the Subscriber tab of CMS.



Open up the Closed Activation Order on the Subscriber’s account.

Type in the “Unit Password” in the Password field of the window. Click on the “Admin Log In” link in the upper right corner of the Linksys page.

A new window will open asking for the user name and password again. This time enter in “admin” as the user name. Type in the “Admin Password” from CMS in the pop up window on the Linksys page. Click on the “Advance View” link to toggle to the page.



Verify that all the settings are set correctly on the “Info” page.



Go to the “System” link on the top of the menu bar.

Verify the settings under the “Optional Network Configuration” section for the “Secondary DNS,” the “DNS Server Order,” the “Syslog Server,” and the “Primary and Secondary NTP Server.”



Next check the settings on the “SIP” page. The “RTP Packet Size” should be set to 0.020



Access the “Provisioning” link from the heading menu bar. Verify that the “Profile Rule” in the “Configuration Profile” and the “Upgrade Rule” in the “Firmware Upgrade” are set as listed below.

The “Region” settings are the next tab to view.



Scroll down to the “Vertical Service Activation Codes.” The “Blind Transfer Code” needs to be set at “44”.

Keep the following code fields blank. “Call Return Code,” “Call Back Act Code,” “Call Back Deact Code,” “Cfwd All Act Code,” “Cfwd All Deact Code,” “Cfwd Busy Act Code,” “Cfwd Busy Deact Code,” “Cfwd No Ans Act Code,” “Cfwd No Ans Deact Code,”

From the “Advanced View” page click on “Line 1” in the heading.



To verify that the settings on the device are correct, first check “Proxy and Registration” then the “Subscriber Information” section. And finally scroll down to the “Audio Configuration” section.

In the “Proxy & Registration” section verify that “Proxy” is set to the Partner’s Domain. The “Outbound Proxy” always needs to be set at “nv-obproxy.commpartners.us” although; the state’s initials can change to represent the state that the Partner is in.

Verify that the “User ID” is correct in the “Subscriber Information” section.



Under “Audio Configuration” Check the setting of the “Preferred Codec.” The normal value is “G729a.” Under the “Use Pref Codec Only” setting should be set at “No.”

Adjusting the Codec to Allow for Fax To allow for fax, remain on the “Line 1” page. Scroll down to the “Audio Configuration” section. Change the “Preferred Codec” setting to “G711u.” Under the “Use Pref Codec Only” switch the setting to “Yes.”

The “Fax Passthru Method” also needs to be changed to “Re Invite.” Click the “Save Settings” button.



Manually Provisioning To manually provision the Linksys ATA PAP2, connect the ATA to power, the network and a telephone set. (As shown on page 2) To access the Linksys web interface, the IP address must be obtained first.

Lift the handset and perform the following tasks to obtain the IP Address;

Enter **** Enter 110# when prompted The ATA device will read the IP Address back to you. Write down the IP address

From the internet browser address window, type in the IP address.

The Linksys web portal for that device will open. Click on the “Admin Login” link.



Click on the “Switch to Advanced View” link.

From the “Provisioning” tab on the top menu bar, under the “Configuration Profile” to enter in the “Profile Rule.”

Profile Rule: http://prov01.commpartners.us/sipura/activation.php?mac=$MAU&devtype=$PN



Scroll down to the “Firmware Upgrade” section and enter the “Upgrade Rule.”

Scroll down to the bottom of the page and click on the “Save Settings” button.

Upgrade Rule: (!2.0.13(LSb))? http://prov01.commpartners.us/linksys_PAP2.bin



A confirmation message will appear before being redirected back to the configuration page.

To complete the provisioning process, power the device off. Return to the Subscriber’s account in CMS. Finish the “Shipping Order” and complete the “Activation Order” as usual. Factory Resetting the Linksys PAP2 Device To factory reset the Linksys ATA PAP2, connect the ATA to power, the network and a telephone set. (As shown on page 2) Using the keypad on the telephone set complete the following process: Enter in: **** Enter in: 73738# Select: 1 to confirm The ATA’s lights will change from blue to red.

linksys ata pap2

Documents