linear actuator with track roller guidance system and toothed belt … · 2019-05-24 · linear...
TRANSCRIPT
Linear actuator with track roller guidancesystem and toothed belt drive
MLF32-ZR, MLF52-ZRFitting and maintenance manual
2 MON 75 Schaeffler Group Industrial
High product safety Our products correspond to the current level of research and technology. If the bearing arrangement is designed correctly,the products are handled and fitted correctly and as agreed andif they are maintained as instructed, they do not give rise to any direct hazards.
Follow instructions This publication describes standard products. Since these are used in numerous applications, we cannot make a judgement as to whether any malfunctions will cause harm to persons or property.
It is always and fundamentally the responsibility of the designerand user to ensure that all specifications are observed and that all necessary safety information is communicated to the end user.This applies in particular to applications in which product failure and malfunction may constitute a hazard to human beings.
Definition of guidelines andsymbols
The warning and hazard symbols are defined along the lines of ANSI Z535.6-2006.
The meaning of the guidelines is as follows:
Warning In case of non-compliance, death or serious injury may occur.
Caution In case of non-compliance, minor or slight injury will occur.
In case of non-compliance, damage or malfunctions in the product or the adjacent construction will occur.
Note! There follows additional or more detailed information that must be observed.
� Numbers within a circle are item numbers.
❏ Squares with a shaded border are placed in front of instructions.
✓ Tick marks indicate preconditions.
Safety guidelines and symbols
Schaeffler Group Industrial MON 75 3
Page
Safety guidelines and symbols High product safety ................................................................... 2
About this manual The purpose of this manual ....................................................... 5
Target group .............................................................................. 5
Safety guidelines for linearactuators
Use for the intended purpose .................................................... 6
General safety guidelines .......................................................... 6
Personnel selection and qualification ........................................ 7
Use of replacement parts........................................................... 7
Overview of the linear actuator Scope of delivery ....................................................................... 8
Available designs ...................................................................... 10
Fitting to the adjacentconstruction
Fixing the support rail to the adjacent construction.................... 12
Fixing the carriage to the adjacent construction ......................... 15
Fitting and mounting ofaccessories
Coupling.................................................................................... 16
Coupling housing ...................................................................... 17
Maintenance Maintenance requirements........................................................ 18
Maintenance intervals ............................................................... 18
Relubrication............................................................................. 19
Cleaning .................................................................................... 21
Removal and dismounting ofcomponents
Linear actuator .......................................................................... 22
Toothed belt unit ....................................................................... 22
Drive unit and return unit........................................................... 26
Carriage..................................................................................... 28
Fitting and mounting ofcomponents
Linear actuator .......................................................................... 29
Carriage..................................................................................... 30
Toothed belt unit ....................................................................... 33
Drive unit and return unit........................................................... 41
Contents
4 MON 75 Schaeffler Group Industrial
Page
Variants Subassemblies ......................................................................... 42
Available variants...................................................................... 44
Multi-piece support rail ............................................................. 44
Multiple carriages ..................................................................... 47
Replacement parts Toothed belt.............................................................................. 48
Drive unit .................................................................................. 48
Return unit ................................................................................ 49
Carriage .................................................................................... 49
Support rail ............................................................................... 50
Appendix Accessories............................................................................... 51
Tightening torques .................................................................... 53
Contents
Schaeffler Group Industrial MON 75 5
The purpose of this manual This fitting and maintenance manual is valid exclusively for the linear actuators stated on the title page.
It describes the secure fitting and maintenance of the linear actuator.
How to use the manual ❑ This manual should be read carefully in full before starting any fitting or maintenance work.
❑ The manual must be stored throughout the life of the linear actuator.
❑ Please ensure that the manual is accessible at all times tothe target group.
❑ The manual must be forwarded to each subsequent owner or operator of the linear actuator or the machine or equipment in which the linear actuator is fitted.
Note! The text and illustrations in this manual cover, by way of an example, the linear actuator MLF32-ZR. For an explanation of the design, see page 10.
The information in this manual can be applied analogously to all variants of the linear actuators stated on the title page.
Target group The target group of this manual comprises the operator andtrained skilled personnel charged with the fitting and maintenance of the linear actuators described.
About this manual
6 MON 75 Schaeffler Group Industrial
Use for the intended purpose All the linear actuators named on the title page are intended exclusively for moving machine components connected to the carriage.
Any other use is not for the intended purpose and is therefore impermissible. The Schaeffler Group accepts no liability for any damage or loss arising therefrom.
General safety guidelines ❑ Any actions and methods that endanger the safety of human beings must not be carried out.
❑ In all fitting and maintenance work, the following must be observed:– all nationally valid and relevant specifications for the
prevention of accidents– all generally recognised rules of safety practice and
occupational medicine.
The linear actuators named on the title page are constructed in accordance with the current level of technology and the recognised rules of safety practice. Nevertheless, while they are being usedthe user or third parties may be put at risk or the linear actuator and other material assets may be impaired.
Risk reduction Risks can be reduced by observing the following points:
❑ The linear actuator should only be operated if it is free from technical defects.
❑ The linear actuator should only be used for the intended purpose and with an awareness of safety and hazards.
❑ If any malfunctions occur that have safety implications, the linear actuator must be stopped immediately and the malfunction rectified by a person with appropriate responsibility.
Fundamental instructions The assembly and fitting of the linear actuator as well as the fitting and dismantling of the individual components must only be carried out as described in this manual:
❑ Carry out the operations in the specified sequence.
❑ Use the listed tools and fitting accessories correctly.Tools and fitting accessories that are unsuitable, damaged or contaminated will impair the function of the linear actuator.
❑ Screws must only be tightened using a torque wrench andthe specified torques must be observed.
❑ Use rubber hammers only, not metal hammers.
❑ Do not use pointed or sharp-edged tools.
Safety guidelines for linear actuators
Schaeffler Group Industrial MON 75 7
Personnel selection andqualification
Persons charged with the fitting and maintenance of the linear actuator must have adequate qualification. They must receive appropriate training and instruction before carrying out fitting or maintenance work.
Providing information to personnel The fitting and maintenance manual must be available in asuitable form to the nominated persons (for example as a printout). This includes drawing explicit attention to the hazard and safety guidelines in this manual.
Disclaimer of liability The Schaeffler Group does not accept any liability for harm to human beings, the linear actuator and the adjacent construction that can be attributed to:
■ incorrect fitting
■ incorrect or inadequate maintenance
■ incorrect communication of the content to third parties ora failure to communicate the content.
Use of replacement parts Special INA replacement parts have been developed for the linear actuators named on the title page. These ensure the reliable and long term function of the linear actuator.
❑ Do not use replacement parts other than original replacement parts from the Schaeffler Group, see page 48.
Use of products from other sources The use of products from other sources instead of INA replacement parts can:
■ change the characteristics of the linear actuator in a negative manner
■ endanger users or third parties
■ cause impairment to the linear actuator and other material assets.
Disclaimer of liability The Schaeffler Group accepts no liability for any damage or loss arising from the use of products from other sources.
8 MON 75 Schaeffler Group Industrial
� Support rail with raceway shafts� Drive unit
(return unit on drive side)� Toothed belt unit
� Lubrication and wiper unit� Carriage with profiled track rollers
� Return unit(return unit on non-driven side)
Figure 1
Subassembliesof linear actuator MLF32-ZR
2
1
0001
4F81
Included in delivery ■ Support rail with raceway shafts �If supplied in several pieces, see section Variants, page 42
■ Drive unit �
Overview of the linear actuator
Schaeffler Group Industrial MON 75 9
5
4
4
3
6
0001
4F82
Scope of delivery – continued ■ Toothed belt unit �Toothed belt and toothed belt clamping devices:The toothed belt is fixed to the carriage by means of the two clamping devices.
■ Carriage with profiled track roller �and lubrication and wiper units �
■ Return unit �
10 MON 75 Schaeffler Group Industrial
Overview of the linear actuator
Available designs The linear actuator is available in different designs.
Track roller guidance system
Carriage
Drive system
Support rail
Note! The text and illustrations in this manual cover, by way of an example, the following design of linear actuator:
■ track roller guidance system of size 32 (MLF32)
■ driven carriage 155 mm long
■ drive shaft on the left side (AL).
The information in this manual can be applied analogously to all variants of the linear actuators stated on the title page.
The precise design of your linear actuator is dependent on your order.
Track roller guidance system Series
Size 32 MLF32
Size 52 MLF52-130
MLF52-145
MLF52-155
Carriage Suffix in ordering designation
Number of driven carriages
1 –
2 Variant, see page 44
Length
MLF32-ZR 155 mm –
300 mm 300
MLF52-130-ZR 200 mm –
300 mm 300
MLF52-145-ZR 245 mm –
500 mm 500
MLF52-155-ZR 260 mm –
500 mm 500
Drive system Suffix in ordering designation
Without drive OA
Drive shaft on right side AR
Drive shaft on left side AL
Drive shaft on both sides (right and left) RL
Without drive shaft OZ
Support rail Suffix in ordering designation
Single-piece –
Multi-piece Variant, see page 44
Schaeffler Group Industrial MON 75 11
Ordering designation The ordering numbers can be found engraved on the drive or return unit.
Ordering example 1Design
Ordering number MLF32-ZR-AL/5 000-4 673
Ordering example 2Design
Ordering number MLF52-155-500ZR-AL/2 600-1857
Variants Variants of the standard designs are shown in the section Variants, see page 44.
Linear actuator with track roller guidance system MLF
Size 32Drive type: one toothed belt ZR
Drive shaft on left side ALNumber of carriages 1
Support rail Single-pieceTotal length of actuator 5 000 mm
Stroke length of actuator 4 673 mm
Linear actuator with track roller guidance system MLF
Size 52Carriage width 155 mm
Carriage length 500 mmDrive type: one toothed belt ZR
Drive shaft on left side ALNumber of carriages 1
Support rail Single-pieceTotal length of actuator 2 600 mm
Stroke length of actuator 1857 mm
12 MON 75 Schaeffler Group Industrial
The linear actuator is fitted in two steps:
■ the support rail is fixed to the adjacent construction
■ the carriage is fixed to the adjacent construction.
Note! Linear actuators more than 8 m long have a multi-piece support rail. They are supplied in several pieces.
❑ If the linear actuator is supplied in several pieces, please observe the section Variants, see page 42.
Fixing the support rail to theadjacent construction
The support rail can be fixed to the adjacent construction usingthe following accessories:
■ clamping lugs, see page 13
■ fixing brackets, see page 13
■ T-nuts to DIN 508, see page 14
■ T-bolts to DIN 787, see page 14
■ T-strips, see page 14
■ hexagonal nuts to DIN 934, see page 14.
Note! Under normal loads, fixing by means of clamping lugsfixing brackets or T-nuts, T-bolts etc. is normally sufficient.
INA connecting brackets Multi-axis handling systems comprising INA linear actuators can be constructed using INA connecting brackets.
Detailed information on the connecting brackets can be found in INA publication Fasteners and connecting brackets for linear actuators (TPI 153).
If linear actuators are not fixed in place correctly, this can damage the linear actuator itself and the adjacent construction.
❑ Note the maximum tightening torques for the fixing screws,see page 53.
❑ Note the maximum spacings for the fasteners.
❑ Ensure that the adjacent construction has adequate strength.
Fitting to the adjacent construction
Schaeffler Group Industrial MON 75 13
Fixing the support rail bymeans of clamping lugs or
fixing brackets
❑ If the support rail is fully in contact with the adjacent construction, clamping lugs or fixing brackets should be fitted on the left and right sides of the support rail at intervals of max. 333 mm.
❑ Under high loads, the support rail should be fixed at shorter intervals or additionally by means of T-nuts or other accessories named on page 12.
MLF32-ZR:A = 100 mmB = 125 mm
MLF52-ZR:A = 137 mmB = 162 mm
Figure 2
Fixing by means of clamping lugs
max. 1
,0 m
0001
4F7B
A
B
14 MON 75 Schaeffler Group Industrial
Fitting to the adjacent construction
Fixing the support rail bymeans of T-nuts
❑ If the support rail is fully in contact with the adjacent construction, T-nuts should be fitted in both profiled slots at intervals of max. 300 mm.
Note! The following accessories can be used instead of T-nuts:
■ T-bolts
■ T-strips with appropriate spacing of the screws
■ hexagonal nuts.
❑ Under high loads, the support rail should be fixed at shorter intervals or additionally by means of clamping lugs or fixing brackets.
MLF32-ZR:B = 43 mm
MLF52-ZR:B = 80 mm
Figure 3
Fixing by means of T-nuts
300
300
300
0001
4F7A
300
300
300
B
Schaeffler Group Industrial MON 75 15
Fixing the carriage to theadjacent construction
The carriage is fixed by means of:
■ threaded rods
■ grub screws.
If linear actuators are not fixed in place correctly, this can damage the linear actuator itself and the adjacent construction.
❑ Note the maximum tightening torques, see page 53.
❑ Ensure that the adjacent construction has adequate strength.
❑ Protect the raceway of the carriage against contamination.
Fixing the carriage ❑ Carriages must be fixed to the adjacent construction in accordance with the loads and the forces acting on them.
16 MON 75 Schaeffler Group Industrial
For the linear actuators stated on the title page, the Schaeffler Group offers specially developed accessories, see section Appendix, page 51.
This section shows the fitting of the following accessories:
■ coupling
■ coupling housing.
Coupling The following tools are required:
■ torque wrench
■ Allen key or hex key inserts.
WarningSudden start of the machine.
Crushing of fingers between the linear actuator and machine parts.
❑ Before starting work, disconnect the machine from the power supply.
❑ Secure the main switch of the machine against switching on.
Fitting the coupling ❑ Slide the coupling onto the drive shaft of the drive unit.There must be a gap of approx. 2 mm left between the coupling and the bearing cover.
❑ Fully tighten the fixing screw. The fixing screw and tightening torque will differ according to the coupling used, for information see INA publication ALE, Driven Linear Units.
Removing the coupling ✓ Coupling housing removed.
❑ Loosen the fixing screw.
❑ Remove the coupling in the direction of the drive shaft.
Figure 4
Screw mounting of the coupling 0001
4F6F
Fitting and mounting of accessories
Schaeffler Group Industrial MON 75 17
Coupling housing The following tools are required:
■ torque wrench
■ Allen key or hex key inserts.
WarningSudden start of the machine.
Crushing of fingers between the linear actuator and machine parts.
❑ Before starting work, disconnect the machine from the power supply.
❑ Secure the main switch of the machine against switching on.
Fitting the coupling housing ✓ Coupling fitted.
❑ Slide the coupling housing over the coupling. The hole in the coupling housing must face towards the adjacent construction, see Figure 5.
❑ Screw mount the coupling housing to the drive unit by means of the fixing screws.– MLF32-ZR: M6/9,5 Nm– MLF52-ZR: M8/23 Nm
Note! The hole in the coupling housing is used to fix and loosen the drive shaft (motor side).
Removing the coupling housing ❑ Loosen the fixing screws.
❑ Remove the coupling housing in the direction of the drive shaft.
� Hole in the coupling housing
Figure 5
Screw mounting of the couplinghousing
1
0001
4F70
18 MON 75 Schaeffler Group Industrial
Maintenance requirements Maintenance work is restricted to:
■ relubrication
■ cleaning.
Maintenance work may require the removal and refitting of components, see page 22 onwards.
Visual inspection In order to ensure exact function and a long operating lifeof the linear actuator, it must be visually inspected for damageand contamination at regular intervals.
Maintenance intervals Maintenance intervals, especially the intervals between relubrication, are influenced by:
■ the travel speed/drive torque
■ the load
■ the temperature
■ the stroke length
■ the environmental conditions (cleanliness etc.).
Maintenance according tooperating conditions
It is not possible to calculate all the influences on maintenance intervals. The intervals can therefore only be determined precisely under operating conditions.
Note! The interval lengths stated in the following sections are maximum maintenance intervals. They must be shortened for each individual case depending on the types of influences present.
Maintenance
Schaeffler Group Industrial MON 75 19
Relubrication Relubrication is necessary for:
■ carriages.
When should relubrication becarried out?
The relubrication interval is dependent on the environmental conditions. Relubrication times and quantities can only be determined precisely under operating conditions.
Relubrication must be carried out:
■ as a function of the application. This must be determined in accordance with the operating conditions.
■ as soon as fretting corrosion1) occurs.
Note! If fretting corrosion occurs, the lubrication intervals should definitely be reduced.
What should be used forrelubrication?
For relubrication of the carriage, oils CL and CLP to DIN 51 517 with a viscosity of ISO-VG 220 are recommended.
Note! Detailed information on recommended lubricants can be found in the INA publication ALE, Driven Linear Units. The INA publication can be requested through [email protected].
What is the relubrication quantity? Guide values for the relubrication quantity are shown in the table.
Relubrication quantity for carriages
Note! It is more advisable to carry out relubrication at several points during the maintenance interval, using partial quantities in each case, than relubrication at the end of the interval using the entire quantity.
1) Fretting corrosion can be identified by a reddish discolouration of the raceway shafts or the outside surface of the track rollers.
Series Relubrication quantity for carriage (guide values)
MLF32-ZR approx. 1 ml to 2 ml
MLF52-ZR approx. 2 ml to 3 ml
20 MON 75 Schaeffler Group Industrial
Maintenance
Relubrication of carriages The carriage is lubricated via felt inserts integrated in the carriage. Relubrication is carried out via the funnel type lubrication nipples on the carriage.
Funnel type lubrication nipples The funnel type lubrication nipples are located on the end faces of the lubrication and wiper units.
Note! The relubrication quantity must be distributed equally to all four funnel type lubrication nipples.
WarningSudden start of the machine.
Crushing of fingers between the carriage and machine parts.
❑ Before starting work, disconnect the machine from the power supply.
❑ Secure the main switch of the machine against switching on.
Relubrication of carriages ✓ Linear actuator warm from operation.
✓ Funnel type lubrication nipples clean and accessible.
❑ Pump one quarter of the required lubricant quantity into each funnel type lubrication nipple. Ensure that all four funnel type lubrication nipples are supplied with oil.
❑ If possible, move the carriage by hand during lubrication in order to distribute the oil evenly.
� Funnel type lubrication nipple
Figure 6
Funnel type lubrication nipples
1
1
1 1
0001
4F2A
Schaeffler Group Industrial MON 75 21
CleaningWhen should cleaning be
carried out?Cleaning must be carried out if heavy contamination is present.
The cleaning requirements are dependent on the environmental and application conditions and can only be determined in the operational state.
Cleaning of components afterremoval
If components must be removed or the linear actuator must be dismantled, the components should be cleaned before refitting.
Damage due to unsuitable cleaning tools or cleaning agents.
❑ Do not use pointed, hard or abrasive objects.
❑ Do not dampen lubricated components during cleaning.
❑ Do not use abrasives, petroleum spirit, oil etc.
What should be used for cleaning? Suitable cleaning tools are:
■ paint brush
■ soft brush
■ soft cloths.
22 MON 75 Schaeffler Group Industrial
Linear actuator The linear actuator is dismantled in the following sequence:
■ remove the toothed belt, see page 23
■ remove the drive unit or return unit, see page 26
■ remove the carriage, see page 28.
Note! It is only necessary in exceptional cases to completely disassemble the linear actuator.
Toothed belt unit The toothed belt unit comprises the toothed belt and two clamping devices. The clamping devices connect the toothed belt to the carriage.
WarningSudden start of the machine.
Crushing of fingers between the carriage and machine parts.
❑ Before starting work, disconnect the machine from the power supply.
❑ Secure the main switch of the machine against switching on.
� Toothed belt
Clamping device:� Lower clamping piece� Upper clamping piece
� Fixing screws� Adjusting screws
Figure 7
Overview of toothed belt unit
5
1
3
4
2
0001
4F71
Removal and dismounting of components
Schaeffler Group Industrial MON 75 23
Removing the toothed belt The following tools are required:
■ torque wrench
■ Allen key or hex key inserts.
Note! The toothed belt is supplied with a factory-specified preload. If the toothed belt is refitted after removal, it must be set to the same preload as before removal, see page 38.
Removing the lubrication andwiper unit
❑ Loosen the screws on the lubrication and wiper unit.
❑ Detach the lubrication and wiper unit carefully from the carriage and remove it from the support rail. During this operation, hold the retainers of the felt inserts securely in place.
Note! The felt inserts may become detached during dismantling.
❑ Refit the felt inserts in the lubrication and wiper unit. Ensure that the springs are inserted as well.
Figure 8
Loosening the lubrication andwiper unit 00
014F
2B
Figure 9
Removing the lubrication andwiper unit 00
014F
32
24 MON 75 Schaeffler Group Industrial
Removal and dismounting of components
Detaching the clamping device fromthe carriage
❑ Loosen and remove the adjusting screws.
❑ Remove the clamping device from the carriage.
Removing the clamping device fromthe toothed belt
❑ Loosen and remove the fixing screws of the clamping device.
❑ Remove the upper and lower clamping pieces from the toothed belt.
❑ If the same toothed belt is refitted: ensure that the grub screws on the upper clamping piece are screwed in to the same depth in order to achieve the original preload.
Figure 10
Loosening the adjusting screws 0001
4F57
Figure 11
Loosening the fixing screws 0001
4F58
� Grub screw
Figure 12
Position of grub screws
1
1
0001
4F73
Schaeffler Group Industrial MON 75 25
Removing the second lubricationand wiper unit
❑ Detach the second lubrication and wiper unit from the carriage and remove it from the support rail.
Detaching the second clampingdevice from the carriage
❑ Detach the second clamping device from the carriage, but do not remove the clamping pieces from the toothed belt.
Note! The second clamping device must only be removed from the toothed belt if the clamping device itself or the toothed belt must be replaced. It is not necessary to remove the second clamping device in order to remove the toothed belt unit.
Removing the toothed belt ❑ Grip the toothed belt by the clamping device and pull it out of the support rail.
Figure 13
Removing the toothed belt 0001
4F59
26 MON 75 Schaeffler Group Industrial
Removal and dismounting of components
Drive unit and return unit The drive unit and return unit differ in their design.However, both components are dismounted in the same way.
Removing the drive unit orreturn unit
The following tools are required:
■ torque wrench
■ Allen key or hex key inserts.
✓ Toothed belt removed, see page 23.
✓ In the case of the drive unit: Motor, coupling and coupling housing removed, see page 16 and page 17.
Removing the toothed belt pulley ❑ Loosen the fixing screws on one bearing cover on the drive unit or return unit as appropriate.
❑ Detach the bearing cover from the housing and slide it out inthe direction of the shaft axis.
� Housing� Fixing screws for housing
� Toothed belt pulley with bearing� Bearing cover
� Fixing screws for bearing cover
Figure 14
Overview of drive unit
1
4
4
5
2
3
0001
4F72
Figure 15
Removing the bearing cover 0001
4F5C
Schaeffler Group Industrial MON 75 27
❑ If the toothed belt pulley was not slid completely out of the housing with the bearing cover, remove the toothed belt pulley completely from the housing with the bearing.
Removing the housing ❑ Remove the second bearing cover from the housing.
❑ Loosen the fixing screws on the housing.
❑ Remove the housing from the support rail.
Figure 16
Removing the toothed belt pulley 0001
4F5D
Figure 17
Unscrewing the housing 0001
4F5E
Figure 18
Removing the housing 0001
4F5F
28 MON 75 Schaeffler Group Industrial
Removal and dismounting of components
Carriage It is only necessary to remove the carriage if it is to be replaced by a new carriage.
Damage due to contaminated lubricant.
The characteristics of oil may change due to contamination.
❑ The work area must be cleaned before removing the carriage.
❑ Elements with oil must be laid only on a clean, lint-free underlay.
Removing the carriage ✓ Drive unit or return unit removed, see page 26.
Damage due to incorrect removal.
❑ While removing the carriage, hold it concentric and parallel tothe support rail.
Removing the carriage ❑ Remove the carriage carefully from the support rail.
� Saddle plate with profiled track rollers� Lubrication and wiper unit
� Felt inserts for relubrication� Fixing screws
Figure 19
Overview of carriage
2
2
1
4
33
0001
4F6A
Figure 20
Removing the carriage 0001
4F61
Schaeffler Group Industrial MON 75 29
Linear actuator A completely disassembled linear actuator is reassembled in the following sequence:
■ fit the carriage, see page 31 to page 32
■ insert the toothed belt, see page 33
■ fit the return unit, see page 34 to page 35
■ fit the drive unit, see page 36 to page 37
■ fix the toothed belt to the carriage, see page 37
■ preload the toothed belt, see page 38 to page 40
■ fix the lubrication and wiper units to the carriage, see page 40.
Fitting and mounting of components
30 MON 75 Schaeffler Group Industrial
Fitting and mounting of components
Carriage
The following tools are required:
■ torque wrench
■ Allen key or hex key inserts
■ ring wrench.
Damage due to incorrect fitting.
❑ Hold the profiled track rollers with the correct fit at the level ofthe raceway shafts.
❑ Hold the carriage concentric and parallel to the support rail.
❑ Ensure that the carriage runs without clearance over the whole length of the support rail.
❑ After fitting, relubricate the carriage, see page 20.
� Saddle plate with profiled track rollers� Lubrication and wiper unit
� Felt inserts for relubrication� Fixing screws
Figure 21
Overview of carriage(completely assembled)
2
2
1
4
3
3
0001
4F68
Schaeffler Group Industrial MON 75 31
Preparing the carriage ❑ Remove the lubrication and wiper units, see page 23.
❑ Remove the black protective caps on the eccentric bolts.
❑ Loosen the nuts on the eccentric bolts until the eccentric bolts can be turned.
❑ Turn the profiled track rollers of the eccentric bolts towards the centre of the carriage.
Sliding the carriage on ❑ Slide the carriage carefully onto the raceway shafts.
� Protective cap on eccentric bolt
Figure 22
Protective caps on eccentric bolts
1
1
0001
4F69
� Profiled track roller with eccentric bolt
Figure 23
Turning the profiled track rollerstowards the centre of the carriage
1
0001
4F6B
Figure 24
Sliding the carriage onto theraceway shafts 00
014F
62
32 MON 75 Schaeffler Group Industrial
Fitting and mounting of components
Setting the profiled track rollersclearance-free
❑ Turn the eccentric bolts until the carriage sits without clearance on the raceway shafts. Move the carriage by hand during this operation.
❑ Tighten the nuts on the eccentric bolts. Ensure that the eccentric bolt does not rotate as well.
– MLF32-ZR: 15 Nm– MLF52-130-ZR and MLF52-145-ZR: 40 Nm– MLF52-155-ZR: 70 Nm
❑ Move the carriage by hand and check whether it can move without clearance over the whole length of the support rail.
Note! If the carriage cannot move without clearance over the whole length of the support rail, please contact Application Engineering at the Linear Technology Division.
Fitting the protective caps ❑ Press the protective caps into the recesses for the eccentric bolts.
Figure 25
Turning the eccentric bolts 0001
4F78
Figure 26
Tightening the nut onthe eccentric bolt 00
014F
79
Schaeffler Group Industrial MON 75 33
Toothed belt unit A component overview is shown in Figure 7, page 22
Overview of fitting The toothed belt is fitted in 6 steps:
■ insert the toothed belt
■ fit the return unit
■ fit the drive unit
■ fix the toothed belt to the carriage
■ preload the toothed belt
■ fit the lubrication and wiper units.
The following tools are required:
■ rubber hammer
■ torque wrench
■ Allen key or hex key inserts
■ screwdriver.
Note! If the toothed belt is refitted after removal, it must be set to the same preload as before removal, see page 38.
Starting point The following instructions are based on the assumption that both the return unit and the drive unit have been removed, see page 26.
If only one of the two units has been removed, go directly to Fitting the drive unit housing, see page 36. In this case, the instructions also apply for fitting of the return unit.
✓ Carriage fitted, see page 31.
Inserting the toothed belt ❑ Insert the toothed belt into the lower hollow section at the open end of the support rail. The teeth of the toothed belt must face upwards.
❑ Continue inserting the toothed belt until only 3 or 4 teeth protrude from the end of the support rail.
Figure 27
Inserting the toothed beltin the support rail 00
014F
67
34 MON 75 Schaeffler Group Industrial
Fitting and mounting of components
Fitting the return unit housing ❑ Locate the return unit housing on the two dowel pins and push it onto the support rail until it stops. Ensure that the toothed belt slides through the lower opening into the housing.
❑ Screw mount the housing on the support rail using fixing screws:– MLF32-ZR: M6/9,5 Nm– MLF52-ZR: M8/23 Nm
Note! The shorter screw must be used for the upper, central hole.
❑ Screw mount 1 bearing cover to the housing:– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M6/9,5 Nm
Note! The shorter screw must be used for the hole on the toothed belt wiper.
� Opening for toothed belt
Figure 28
Locating the housing
1
0001
4F66
Figure 29
Screw mounting of the housing 0001
4F65
Schaeffler Group Industrial MON 75 35
Fitting the toothed belt pulley ❑ Insert the toothed belt pulley into the housing.
Damage to the toothed belt and return unit due to unsuitable tools.
❑ Do not use pointed or sharp-edged tools.
Inserting the toothed belt ❑ Feed the toothed belt onto the teeth of the toothed belt pulley with the aid of a screwdriver. Hold the screwdriver flat between two teeth on the toothed belt.
❑ Guide the toothed belt over the toothed belt pulley and pull it approx. 200 mm out of the top of the return unit.
Closing the return housing ❑ Locate the bearing cover and screw mount using fixing screws:– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M6/9,5 Nm
Note! The shorter screw must be used for the hole on the toothed belt wiper.
Figure 30
Inserting the toothed belt pulley 0001
4F64
Figure 31
Feeding the toothed belt onto thetoothed belt pulley 00
014F
6D
36 MON 75 Schaeffler Group Industrial
Fitting and mounting of components
Fitting the drive unit housing ❑ Draw the toothed belt out of the return unit until its other end protrudes by 3 or 4 teeth from the open end of the support rail.
❑ Locate the drive unit housing on the two dowel pins and push it onto the support rail until it stops. Ensure that the toothed belt slides through the lower opening into the housing.
❑ Screw mount the housing on the support rail using fixing screws:– MLF32-ZR: M6/9,5 Nm– MLF52-ZR: M8/23 Nm
❑ 1 Screw mount 1 bearing cover to the housing:– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M6/9,5 Nm
❑ Insert the toothed belt pulley into the housing.
Inserting the toothed belt ❑ Feed the toothed belt onto the teeth of the toothed belt pulley.
❑ Guide the toothed belt over the toothed belt pulley and pull it approx. 200 mm out of the top of the drive unit.
� Opening for toothed belt
Figure 32
Locating the housing
1
0001
4F60
Figure 33
Feeding the toothed belt onto thetoothed belt pulley 00
014F
6C
Schaeffler Group Industrial MON 75 37
Closing the drive unit housing ❑ Locate the bearing cover on the drive axis and slide it against the housing. If necessary, carefully knock the bearing cover into place using a rubber hammer.
❑ Insert fixing screws into the (outer) holes and screw mount the bearing cover:– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M6/9,5 Nm
Note! The inner holes on the drive unit are intended for the coupling housing.
Fixing the clamping device to thetoothed belt
❑ Position the toothed belt on the lower clamping piece.The toothed belt must completely cover the clamping piece.The bevelled corners of the clamping piece face towards the carriage.
❑ Screw mount the upper and lower clamping pieces of the first clamping device to the toothed belt:
– MLF32-ZR: M4/2,7 Nm– MLF52-ZR: M5/5,5 Nm
Figure 34
Positioning the toothed belt on thelower clamping piece 00
014F
77
Figure 35
Screw mounting the clampingdevice to the toothed belt 00
014F
6E
38 MON 75 Schaeffler Group Industrial
Fitting and mounting of components
Fixing the toothed belt to thecarriage
❑ Screw mount the clamping device to the carriage using the adjusting screw:– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M5/5,5 Nm
❑ Screw mount the second clamping device to the toothed belt:– MLF32-ZR: M4/2,7 Nm– MLF52-ZR: M5/5,5 Nm
❑ Screw mount the clamping device to the carriage loosely enough that the toothed belt is not yet tensioned.
Preloading the toothed beltduring refitting
When refitting a toothed belt that has been removed:
❑ tighten the clamping device to the hard stop.
– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M5/5,5 Nm
Note! ❑ The grub screws on the upper clamping pieces must be screwed in to the same depth as they were before the toothed belt was removed. If they are screwed in to a different depth, the procedure to be followed must be the same as that for fitting a new toothed belt.
Figure 36
Screw mounting the clampingdevice to the carriage 00
014F
57
MLF32-ZR:� Grub screw M4
MLF52-ZR:� Grub screw M5
Figure 37
Position of grub screws
1
1
0001
4F73
Schaeffler Group Industrial MON 75 39
Preloading a new toothed belt When fitting a new toothed belt:
❑ Mark a measurement length of 1000 mm on the untensioned toothed belt. In order to increase the measurement accuracy,the measurement length can be extended in the case of longer linear actuators (2 000 mm, 3 000 mm etc.).
❑ Tighten the adjusting screw on the second clamping device until the measurement length is extended by the preload elongation. The elongation is as follows:
– MLF32-ZR: 2 mm/1000 mm– MLF52-ZR: 1,6 mm/1000 mm
❑ If the clamping device cannot be recessed far enough in the carriage, undo the grub screws on the upper clamping piece as far as necessary. For the position of the grub screws, see Figure 37, page 38.
Figure 38
Measurement length marked(not to scale) 00
014F
25
Figure 39
Measurement length preloaded(not to scale) 00
014F
29
40 MON 75 Schaeffler Group Industrial
Fitting and mounting of components
Fixing the toothed belt preload ❑ Once the preload has been achieved, tighten the grub screws to the hard stop.
– MLF32-ZR: M4/2,7 Nm– MLF52-ZR: M5/5,5 Nm
❑ Check the correct preload using the measurement marks.Make corrections if necessary.
Fixing the lubrication and wiperunits to the carriage
❑ If the lubrication felt inserts are secured by means of rubber rings, remove the rubber rings.
❑ Position both lubrication and wiper units carefully on the support rail. Ensure that the lubrication felt inserts are correctly seated in the lubrication and wiper units.
❑ Screw mount the lubrication and wiper units to the carriage:
– MLF32-ZR: M5/5,5 Nm– MLF52-ZR: M6/9,5 Nm
Figure 40
Fixing the preload 0001
4F46
Figure 41
Screw mounting of the lubricationand wiper unit 00
014F
2B
Schaeffler Group Industrial MON 75 41
Drive unit and return unit A component overview is shown in Figure 14, page 26.
The following tools are required:
■ rubber hammer
■ torque wrench
■ Allen key or hex key inserts.
✓ Toothed belt inserted in the profiled section, see page 33.
Fitting the drive unit or return unit ❑ For fitting of the drive unit, see page 36.
❑ For fitting of the return unit, see page 34.
42 MON 75 Schaeffler Group Industrial
� Support rail with raceway shafts� Drive unit
(return unit on drive side)� Toothed belt unit
� Lubrication and wiper unit� Carriage with profiled track rollers
� Return unit(return unit on non-driven side)
Figure 42
Subassembliesof linear actuator MLF32-ZR,
multi-piece design
2
1
0001
4F7E
Subassemblies ■ Multi-piece support rail with raceway shafts and retaining plates �,two retaining plates supplied per profiled section joint
■ Drive unit �
Variants
Schaeffler Group Industrial MON 75 43
5
3
4
6
4
0001
4F7F
Subassemblies – continued ■ Toothed belt unit �Toothed belt and toothed belt clamping devices:The toothed belt is fixed to the carriage by means of the two clamping devices
■ Carriage with profiled track rollers �and lubrication and wiper units �
■ Return unit �
44 MON 75 Schaeffler Group Industrial
Variants
Available variants
1) X = number of support rail joints
Ordering exampleDesign
Ordering designation MLF52-155-500-ZR-RL-W2-FA517.1/10 000-9 257
Multi-piece support rail Linear actuators more than 8 m long are supplied in several pieces. They must be assembled before fitting into the adjacent construction.
Note! If a delivery includes two or more multi-piece linear actuators,the individual pieces of each actuator are identified by the same letter on the joints of the profiled sections.
Example Linear actuator 1: A1, A2, A3, etc.
Linear actuator 2: B1, B2, B3, etc.
Carriage Suffix in ordering designation
2 driven carriages W2
Support rail Suffix in ordering designation
Multi-piece FA517.X1)
Linear actuator with track roller guidance system MLFSize 52
Width of carriage 155 mmLength of carriage 500 mm
Drive type: one toothed belt ZRDrive shaft on both sides RL
Two carriages W2Multi-piece support rail FA517.1
Total length of actuator 10 000 mmStroke length of actuator 9 257 mm
Schaeffler Group Industrial MON 75 45
Assembling the support rail The following tools are required:
■ rubber hammer
■ torque wrench
■ Allen key or hex key inserts.
CautionRisk of injury due to falling support rails.
❑ Ensure that support rails cannot drop from the working area.
Positioning of individual pieces ❑ The individual pieces of the support rail must be arranged consecutively in the correct sequence. The combinations of letters and numbers must match, see Figure 44.
Example Correct: profiled section joint A1 – A1
Incorrect: profiled section joint A1 – A2
❑ Slide the T-nuts for the retaining plates into the T-slots in the sides.
❑ Slide the individual pieces of the support rail together.
Figure 43
Arranging the support rails 0001
4F85
Figure 44
Example of letter and numbercombination for profiled
section joint 0001
37D
5
46 MON 75 Schaeffler Group Industrial
Variants
Joining the individual pieces ❑ Locate the retaining plates at the centre of the profiled section joints using the fixing screws M6.
❑ Check whether the raceway shafts on the individual sections abut each other precisely. If necessary, correct the position of the individual pieces.
❑ Fix the retaining plates to the support rail by dowels using the two outermost dowel holes. Use the dowel holes in the support rail for this purpose.
Note! The dowel hole at one end of the retaining plate is designed as a slot.
❑ Tighten the grub screws at the slots to the abutment point.
❑ Check the joint location again.
❑ Fasten the fixing screws in the retaining plates to a torque of 9,5 Nm.
❑ Drill through the support rail at the remaining dowel holes inthe retaining plates to a diameter 6 H7 and a depth of approx. 20 mm.
❑ Knock in the dowel pins.
Fitting the components ❑ For fitting of further components, see section Fitting and mounting of components, page 29.
Figure 45
Locating the retaining plates 0001
4F5A
� Grub screw� Slot
Figure 46
Grub screw and slot
2
1
0001
4F5B
Schaeffler Group Industrial MON 75 47
Multiple carriages If the linear actuator has more than one carriage, these have a passage for the toothed belt and are free to move individually.They are connected to each other by means of the adjacent construction.
Fitting of multiple carriages The following tools are required:
■ rubber hammer
■ torque wrench
■ Allen key or hex key inserts
■ screwdriver.
✓ All carriages slid onto raceway shafts, see page 31 to page 32.
✓ Toothed belt inserted but not yet fitted with clamping devices, see page 33 to page 37.
✓ Lubrication and wiper units fixed to the freely movable carriages, see page 40.
Fitting the toothed belt ❑ Pass the toothed belt between the support rail and the underside of the freely movable carriages.
❑ Fix the toothed belt to the driven carriage, see page 37 topage 40.
Fixing the carriage to the adjacentconstruction
❑ Fix all carriages to the adjacent construction, see page 15.
Figure 47
Passing the toothed belt underthe carriages 00
014F
63
48 MON 75 Schaeffler Group Industrial
Note! The precise design of your linear actuator is dependent on your order. When ordering replacement parts, please indicate the ordering number of your linear actuator. The ordering numbers can be found engraved on the drive unit or return unit.
Toothed belt
Replacement parts list fortoothed belt
Drive unit
Replacement parts list for drive unit
0001
4F87
Linear actuator Designation MATNR
MLF32-ZR ZHRI20-AT-5 000116742-0000
MLF52-ZR ZHRI32-AT-10 000148814-0000
0001
4F7C
Linear actuator Designation MATNR
Drive shaft on left or right side
MLF32-ZR UML.MLF32-ZR-AR-7500 000595861-0000
MLF52-ZR UML.MLF52-ZR-AR-7500 000148792-0000
Drive shaft on both sides
MLF32-ZR UML.MLF32-ZR-RL-7500 000695505-0000
MLF52-ZR UML.MLF52-ZR-RL-7500 000362344-0000
Replacement parts
Schaeffler Group Industrial MON 75 49
Return unit
Replacement parts list forreturn unit
Carriage
Replacement parts list for carriage
0001
4F86
Linear actuator Designation MATNR
MLF32-ZR UML.MLF32-ZR-7500 000049395-0000
MLF52-ZR UML.MLF52-ZR-7500 001189840-0000
0001
4F83
Linear actuator Designation MATNR
MLF32-ZR
Carriage length 155 mm LFKL.MLF32-ZR-4400 000556106-0000
Carriage length 300 mm LFKL.MLF32-300-ZR-4400 003369188-0000
MLF52-130-ZR
Carriage length 200 mm LFKL.MLF52-130-ZR-4400 001189794-0000
Carriage length 300 mm LFKL.MLF52-130-300-ZR-4400 003369072-0000
MLF52-145-ZR
Carriage length 245 mm LFKL.MLF52-145-ZR-4400 000082430-0000
Carriage length 500 mm LFKL.MLF52-145-500-ZR-4400 003369056-0000
MLF52-155-ZR
Carriage length 260 mm LFKL.MLF52-155-ZR-4400 000082481-0000
Carriage length 500 mm LFKL.MLF52-155-500-ZR-4400 003369030-0000
50 MON 75 Schaeffler Group Industrial
Replacement parts
Support rail
Replacement parts list forsupport rail
0001
4F84
Linear actuator Designation MATNR
MLF32-ZR LFS.MLF32-ZR-4700 000595829-0000
MLF52-ZR LFS.MLF52-ZR-4700 000479314-0000
Schaeffler Group Industrial MON 75 51
Accessories Special INA replacement parts have been developed for the linear actuators named on the title page. These ensure the reliable and long term function of the linear actuators.
Location
1) Clamping lugs can support higher forces. They should be used in preference over fixing brackets.
Accessory Article number
Clamping lugs1) SPPR28x30
Fixing brackets1) WKL48x35
WKL98x35
T-strips (steel) Leis-M6-T-Nut
Leis-M8-T-Nut
T-nuts MU-DIN508-M4x8
MU-DIN508-M6x8
MU-M4x8-Rhombus
MU-M6x8-POS
MU-M6x8-Rhombus
MU-M8x8-POS
T-bolts SHR-DIN787-M8x8x32
Slot closing strips NAD8x11,5
Connecting brackets See INA publication Fasteners and connecting brackets for linear actuators (TPI 153)
Appendix
52 MON 75 Schaeffler Group Industrial
Appendix
Coupling, gearbox, motor As a system supplier, the Schaeffler Group also offers components including coupling housings, couplings, gearboxes and motors. These components are precisely matched to the linear actuator.
MLF32-ZR
1) i = ratio
MLF52-ZR
1) i = ratio
Comprehensive information can be found in INA publication ALE, Driven Linear Units and on the Internet at www.schaeffler.com
Coupling Coupling housing Gearbox and motor1)
KUP-560-56-16H7/20H7 KGEH32/43 000-MLF-ZR GETR-PL70-i
KUP-560-56-20H7/20H7 KGEH32/43 100-MLF-ZR GETR-PL90-i
KUP-560-56-20H7/20H7 KGEH32/43 100-MLF-ZR GETR-PLE80/90-i
KUP-560-56-19H7/20H7 KGEH32/36 200-MLF-ZR MOT-SMH100 ...
Coupling Coupling housing Gearbox and motor1)
KUP-560-56-16H7/20H7 KGEH52/43 000-MLF-ZR GETR-PL70-i
KUP-560-56-20H7/20H7 KGEH52/43 100-MLF-ZR GETR-PL90-i
KUP-560-56-20H7/20H7 KGEH52/43 100-MLF-ZR GETR-PLE80/90-i
KUP-560-56-20H7/24H7 KGEH52/36 000-MLF-ZR MOT-MH145 ...
Schaeffler Group Industrial MON 75 53
Tightening torques The correct tightening torques are shown in the table.
Screw Grade Tightening torqueNm
M4 8.8 2,7
10.9 4,3
12.9 5,1
M5 8.8 5,5
10.9 8,4
12.9 10,2
M6 8.8 9,5
10.9 14,7
12.9 17,6
M8 8.8 23
10.9 35,3
12.9 42,2
M10 8.8 46
10.9 67
12.9 78
M12 8.8 80
10.9 115
12.9 135
Schaeffler KG
Linear Technology Division
Berliner Straße 134
66424 Homburg/Saar (Germany)
Internet www.ina.com
E-mail [email protected]
In Germany:
Phone 0180 5003872
Fax 0180 5003873
From Other Countries:
Phone +49 6841 701-0
Fax +49 6841 701-2625
Every care has been taken to ensure the
correctness of the information contained
in this publication but no liability can be
accepted for any errors or omissions.
We reserve the right to make technical
changes.
© Schaeffler KG · 2009, January
This publication or parts thereof may not
be reproduced without our permission.
MON 75 GB-DMO
N 7
5 /
GB
-D /
200
901
/ pd
f onl
y