lg lcd ld74a 32lt75

LCD TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : LD74A

MODEL : 32LT75/76 32LT75/76-ZA

North/Latin America http://aic.lgservice.comEurope/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com

Internal Use Only

- 2 - LGE Internal Use OnlyCopyright © 2007 LG Electronics. Inc. All right reserved. Only for training and service purposes

CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ..................................................................................3

SPECIFICATION ........................................................................................6

ADJUSTMENT INSTRUCTION ...............................................................10

TROUBLE SHOOTING ............................................................................14

BLOCK DIAGRAM...................................................................................23

EXPLODED VIEW .................................................................................. 28

REPLACEMENT PARTS LIST ............................................................... 30

SVC. SHEET ...............................................................................................

LGE Internal Use OnlyCopyright © 2007 LG Electronics. Inc. All right reserved. Only for training and service purposes

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in theSchematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to preventShock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during theservicing of a receiver whose chassis is not isolated from the ACpower line. Use a transformer of adequate power rating as thisprotects the technician from accidents resulting in personal injuryfrom electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown,replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor,over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposedmetallic parts of the cabinet, such as antennas, terminals, etc., tobe sure the set is safe to operate without damage of electricalshock.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect anelectrical jumper across the two AC plug prongs. Place the ACswitch in the on position, connect one lead of ohm-meter to the ACplug prongs tied together and touch other ohm-meter lead in turn toeach exposed metallic parts such as antenna terminals, phonejacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using AC voltmeterwith 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat AC voltagemeasurements for each exposed metallic part. Any voltagemeasured must not exceed 0.75 volt RMS which is corresponds to0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF


- 4 -

CAUTION: Before servicing receivers covered by this servicemanual and its supplements and addenda, read and follow theSAFETY PRECAUTIONS on page 3 of this publication.NOTE: If unforeseen circumstances create conflict between thefollowing servicing precautions and any of the safety precautions onpage 3 of this publication, always follow the safety precautions.Remember: Safety First.

General Servicing Precautions1. Always unplug the receiver AC power cord from the AC power

source before;a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.CAUTION: A wrong part substitution or incorrect polarityinstallation of electrolytic capacitors may result in anexplosion hazard.

2. Test high voltage only by measuring it with an appropriate highvoltage meter or other voltage measuring device (DVM,FETVOM, etc) equipped with a suitable high voltage probe.Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of itsassemblies.

4. Unless specified otherwise in this service manual, cleanelectrical contacts only by applying the following mixture to thecontacts with a pipe cleaner, cotton-tipped stick or comparablenon-abrasive applicator; 10% (by volume) Acetone and 90% (byvolume) isopropyl alcohol (90%-99% strength)CAUTION: This is a flammable mixture.Unless specified otherwise in this service manual, lubrication ofcontacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with whichreceivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of itselectrical assemblies unless all solid-state device heat sinks arecorrectly installed.

7. Always connect the test receiver ground lead to the receiverchassis ground before connecting the test receiver positivelead.Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in thisservice manual.CAUTION: Do not connect the test fixture ground strap to anyheat sink in this receiver.

Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can be damaged easilyby static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ESdevices are integrated circuits and some field-effect transistors andsemiconductor "chip" components. The following techniquesshould be used to help reduce the incidence of componentdamage caused by static by static electricity.1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostaticcharge on your body by touching a known earth ground.Alternatively, obtain and wear a commercially availabledischarging wrist strap device, which should be removed toprevent potential shock reasons prior to applying power to the

unit under test.2. After removing an electrical assembly equipped with ES

devices, place the assembly on a conductive surface such asaluminum foil, to prevent electrostatic charge buildup orexposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ESdevices.

4. Use only an anti-static type solder removal device. Some solderremoval devices not classified as "anti-static" can generateelectrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generateelectrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protectivepackage until immediately before you are ready to install it.(Most replacement ES devices are packaged with leadselectrically shorted together by conductive foam, aluminum foilor comparable conductive material).

7. Immediately before removing the protective material from theleads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will beinstalled.CAUTION: Be sure no power is applied to the chassis or circuit,and observe all other safety precautions.

8. Minimize bodily motions when handling unpackagedreplacement ES devices. (Otherwise harmless motion such asthe brushing together of your clothes fabric or the lifting of yourfoot from a carpeted floor can generate static electricitysufficient to damage an ES device.)

General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and appropriate

tip size and shape that will maintain tip temperature within therange or 500°F to 600°F.

2. Use an appropriate gauge of RMA resin-core solder composedof 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a mall wire-

bristle (0.5 inch, or 1.25cm) brush with a metal handle.Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering techniquea. Allow the soldering iron tip to reach normal temperature.

(500°F to 600°F)b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.CAUTION: Work quickly to avoid overheating the circuitboard printed foil.

6. Use the following soldering technique.a. Allow the soldering iron tip to reach a normal temperature

(500°F to 600°F)b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it thereonly until the solder flows onto and around both thecomponent lead and the foil.CAUTION: Work quickly to avoid overheating the circuitboard printed foil.

d. Closely inspect the solder area and remove any excess orsplashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS


- 5 -

IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong) throughwhich the IC leads are inserted and then bent flat against thecircuit foil. When holes are the slotted type, the following techniqueshould be used to remove and replace the IC. When working withboards using the familiar round hole, use the standard techniqueas outlined in paragraphs 5 and 6 above.

Removal1. Desolder and straighten each IC lead in one operation by gently

prying up on the lead with the soldering iron tip as the soldermelts.

2. Draw away the melted solder with an anti-static suction-typesolder removal device (or with solder braid) before removing theIC.

Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad and

solder it.3. Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as close as

possible to the component body.2. Bend into a "U" shape the end of each of three leads remaining

on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" withlong nose pliers to insure metal to metal contact then soldereach connection.

Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the circuit

board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.

Diode Removal/Replacement1. Remove defective diode by clipping its leads as close as

possible to diode body.2. Bend the two remaining leads perpendicular y to the circuit

board.3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and ifnecessary, apply additional solder.

Fuse and Conventional ResistorRemoval/Replacement1. Clip each fuse or resistor lead at top of the circuit board hollow

stake.2. Securely crimp the leads of replacement component around

notch at stake top.3. Solder the connections.

CAUTION: Maintain original spacing between the replacedcomponent and adjacent components and the circuit board toprevent excessive component temperatures.

Circuit Board Foil RepairExcessive heat applied to the copper foil of any printed circuitboard will weaken the adhesive that bonds the foil to the circuitboard causing the foil to separate from or "lift-off" the board. Thefollowing guidelines and procedures should be followed wheneverthis condition is encountered.

At IC ConnectionsTo repair a defective copper pattern at IC connections use thefollowing procedure to install a jumper wire on the copper patternside of the circuit board. (Use this technique only on ICconnections).

1. Carefully remove the damaged copper pattern with a sharpknife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (ifused) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire andcarefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copperpattern and let it overlap the previously scraped end of the goodcopper pattern. Solder the overlapped area and clip off anyexcess jumper wire.

At Other ConnectionsUse the following technique to repair the defective copper patternat connections other than IC Pins. This technique involves theinstallation of a jumper wire on the component side of the circuitboard.

1. Remove the defective copper pattern with a sharp knife.Remove at least 1/4 inch of copper, to ensure that a hazardouscondition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the patternbreak and locate the nearest component that is directlyconnected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of thenearest component on one side of the pattern break to the leadof the nearest component on the other side.Carefully crimp and solder the connections.CAUTION: Be sure the insulated jumper wire is dressed so theit does not touch components or sharp edges.


- 6 -

SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.

1. General Specification(LCD MODULE)

2. Model General Specification

Item Specification Remark

Market UK, France, Germany, Spain, Sweden, Finland, Italy

Broadcasting system PAL-BG UK, France, Germany, Spain, Sweden, Finland, Italy

PAL-DK

PAL-I,I’

DVB-T (ID TV)

Receiving system Analog : Upper Heterodyne

Digital : COFDM

Scart Jack (2EA) PAL, SECAM Scart 1 Jack is Full scart and support RF-OUT(analog)

Scart 2 jack is Half scart and support MNT-OUT.

Video Input (2EA) PAL, SECAM, NTSC 4 System :

PAL, SECAM, NTSC, PAL60

S-Video Input (1EA) PAL, SECAM, NTSC 4 System :

PAL, SECAM, NTSC, PAL60

Component Input (1EA) Y/Cb/Cr, Y/ Pb/Pr

RGB Input RGB-PC,

RGB-DTV

HDMI Input (2EA) HDMI-PC

HDMI-DTV & SOUND

Audio Input (4 EA) PC Audio, Component, AV (2EA) L/R Input

Item Specification Remark

Display Screen Device 32” wide Color Display Module LCD

Aspect Ratio 16:9

LCD Module 32” TFT WXGA LCD MAKER : LPL

Operating Environment Temp. : 0 ~ 40 deg

Humidity : 0 ~ 85% LGE SPEC

Storage Environment Temp. : -20 ~ 60 deg

Humidity : 0 ~ 85 %

Input Voltage 100-240V~, 50/60Hz

Power Consumption Power on (Green)

Total 114.32W (Typ.) (Logic=4.32(4.1)W, Backlight =110W )

St-By (Red) : 1.0 W

Type Size 760.0 x 450.0 x 48.0

Pixel Pitch 0.17025 x 0.51075

Back Light 18 EEFL

Display Colors 16.7M (16,777,216)

Coating 3H, AG


Item Min Typ Max Unit Maker Remark

Luminance 400 500 cd/m LPL(0RT)32” -50cm from the surface

(W/O PC mode) - Full White Pattern

View angle (R/L, U/D) 178/178 degree 32”

Color Coordinate White X Typ. 0.279/0.279/0.279 Typ. LPL 32”

Y -0.03 0.292/0.292/0.292 +0.03

Red X 0.635/0.636/0.635

Y 0.339/0.343/0.344

Green X 0.282/0.284/0.286

Y 0.606/0.615/0.614

Blue X 0.145/0.144/0.146

Y 0.064/0.063/0.061

Contrast ratio

(W/O PC mode) 600 800 32” LPL(0-RT)

Luminance Variation 1.3

- 7 -

3. Chroma & Brightness (LCD Module-LPL)

4. Component Video Input (Y, PB, PR)

NoSpecification

ProposedResolution H-freq(kHz) V-freq(Hz)

1 720*480 15.73 60.00 SDTV, DVD 480i

2 720*480 15.63 59.94 SDTV, DVD 480i

3 720*480 31.47 59.94 480p

4 720*576 15.625 50.00 SDTV, DVD 625 Line

5 720*576 31.25 50.00 HDTV 576p

6 1280*720 45.00 50.00 HDTV 720p

7 1280*720 44.96 59.94 HDTV 720p

8 1920*1080 31.25 50.00 HDTV 1080i

9 1920*1080 33.75 60.00 HDTV 1080i

10 1920*1080 33.72 59.94 HDTV 1080i


- 8 -

6. HDMI input (DTV Mode)

5. RGB PC INPUT Mode Table

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1. 720*400 31.468 70.08 28.321

2. 640*480 31.469 59.94 25.17 VESA Input 848*480 60Hz, 852*480 60Hz

37.684 75.00 31.50 --> 640*480 60Hz Display

3 800*600 37.879 60.31 40.00 VESA

46.875 75.00 49.50

4 832*624 49.725 74.55 57.283 Macintosh

5 1024*768 48.363 60.00 65.00 VESA(XGA)

56.470 70.00 75.00

60.123 75.029 78.75

6 1280*768 47.78 59.87 79.5 WXGA

7 1360*768 47.72 59.8 84.75 WXGA

8 1366*768 47.56 59.6 84.75 WXGA

9 1280*1024 63.595 60.0 108.875 SXGA FHD Model only


11 1600*1200 74.077 60.0 130.375 UXGA Reduced Blanking Timing, FHD Model only

Input 1920*1200 60Hz -> 1600*1200 60Hz Display

12 1920*1080 66.647 59.988 138.625 WUXGA Reduced Blanking Timing


1. 720*480 31.47 59.94 27.00 SDTV 480P(4:3) PC mode -> 640*480 60Hz Display

2. 720*480 31.50 60 27.027 SDTV 480P(4:3)

3. 640*480 31.469 59.94 25.175 SDTV 480P(4:3)

4. 640*480 31.469 60.00 25.20 SDTV 480P(4:3)

5. 720*480 31.47 59.94 27.000 SDTV 480P(16:9)

6. 720*480 31.50 60.00 27.027 SDTV 480P(16:9)

7. 720*576 31.25 50.00 27.000 SDTV 576P

8. 1280*720 37.50 50.00 74.176 HDTV 720P

9. 1280*720 44.96 59.94 74.176 HDTV 720P PC mode -> 1280*720 60Hz Display

10. 1280*720 45.00 60.00 74.250 HDTV 720P

11 1920*1080 33.72 59.94 74.176 HDTV 1080I

12 1920*1080 33.75 60.00 74.250 HDTV 1080I

13 1920*1080 28.125 50.00 74.250 HDTV 1080I 50Hz

14 1920*1080 27.000 24.00 74.250 HDTV 1080P 24Hz

15 1920*1080 56.250 50 148.500 HDTV 1080P 50Hz

16 1920*1080 67.433 59.94 148.352 HDTV 1080P PC mode -> 1920*1080 60Hz Display

17 1920*1080 67.500 60 148.500 HDTV 1080P


- 9 -

7. HDMI input (PC Mode)


1. 720*400 31.468 70.08 28.321

2. 640*480 31.469 59.94 25.17 VESA DTV mode --> 480p Display

37.684 75.00 31.50 848*480 60Hz, 852*480 60Hz Ë No signal

3 800*600 37.879 60.31 40.00 VESA

46.875 75.00 49.50

4. 832*624 49.725 74.55 57.283 Macintosh

5. 1024*768 48.363 60.00 65.00 VESA(XGA)

56.470 70.00 75.00

60.123 75.029 78.75

6 1280*768 47.78 59.87 79.5 WXGA PC mode only

7 1360*768 47.72 59.8 84.75 WXGA

8 1366*768 47.56 59.6 84.75 WXGA



11 1600*1200 74.077 60.0 130.375 UXGA Reduced Blanking Timing, FHD Model only

Input 1920*1200 60Hz --> No Signal

12 1920*1080 66.647 59.988 138.625 WUXGA Reduced Blanking Timing

DTV mode --> 1080P Display


- 10 -

ADJUSTMENT INSTRUCTION

1. Application RangeThis spec. sheet is applied to all of the LD74A chassismanufactured at LG TV Plant all over the world.

2. Specification.1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation transformer will help toprotect test instruments

2) Adjustment must be done in the correct sequence.3) The adjustment must be performed at 25±5°C temperature

and 65±10% relative humidity if there is no specifieddesignation.

4) The input voltage of the receiver must be kept between100-220V~, 50/60Hz.

5) Before adjustment, execute Heat-Run for 30 minutes at RFno signal.

3. Channel Memory1) Press ADJ key in Adjust remote control.2) Select “Channel Recover” by using D/E (CH+/-) key, and

press G (VOL+).3) The set is turned off automatically.4) Press ‘power’ key of Adjust Remote control.

4. EDID* Caution

1) Use the proper signal cable for EDID Download- Analog EDID : Pin3 exists- Digital EDID : Pin3 exists

2) Never connect HDMI & D-sub Cable at the same time.3) Use the proper cables below for EDID Writing.4) Download HDMI1, HDMI2 separately because HDMI1 is

different from HDMI2.

4.1. EDID Data

4.2. Data(1) ANALOG (128 bytes)

(2) HDMI 1 (256 bytes)=>

=> Detail EDID Options are below (a, b, c, d, e-1, e-2, f-1, f-2)

(3) HDMI 2 (256 bytes)

=> Detail EDID Options are below (a, b, c, d, e-1, e-2, f-1, f-2)

Product ID Serial No: Controlled on production line. Month, Year: Controlled on production line:

ex) Monthly : ‘09’ -> ‘09’ Year : ‘2006’ -> ‘10’

Model Name(Hex): -1, -2, -1, -2 Checksum: Changeable by totalEDID data.

Item

Manufacurer ID

Version

Revision

Condition

GSM

Digital : 1

Digital : 3

Data(Hex)

1E6D

01

03

D-sub to D-sub DVI-D to HDMI or HDMI ro HDMI

For HDMI EDID

0x000x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C0x0D 0x0E 0x0F

0x00 00 FF FF FF FF FF FF 00 1E 6D

0x01 01 03 01 46 27 78 EA D9 B0 A3 57 49 9C 25

0x02 11 49 4B A5 6E 00 31 40 45 40 61 40 D1 C0 01 01

0x03 01 01 01 01 01 01 1B 21 50 A0 51 00 1E 30 48 88

0x04 35 00 BC 86 21 00 00 1C 26 36 80 A0 70 38 1F 40

0x05 50 20 85 04 BC 86 21 00 00 18

0x06 00 00 00 FD

0x07 00 3C 4B 1D 43 0E 00 0A 20 20 20 20 20 20 00 -1

For Analog EDID

0x000x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B0x0C0x0D 0x0E 0x0F


0x01 01 03 80 46 27 78 EA D9 B0 A3 57 49 9C 25

0x02 11 49 4B A5 6E 00 31 40 45 40 61 40 D1 C0 01 01

0x03 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

0x04 45 00 C4 8E 21 00 00 1E 1B 21 50 A0 51 00 1E 30

0x05 48 88 35 00 BC 86 21 00 00 1C

0x06 00 00 00 FD

0x07 00 32 4B 1C 43 0F 00 0A 20 20 20 20 20 20 01 -2

0x00 02 03 21 F1 4E 02 11 01 03 12 13 04 14 05 21 1F

0x01 20 22 10 23 09 07 07 83 01 00 00 65 3 0C 00 10

0x02 00 01 1D 00 BC 52 D0 1E 20 B8 28 55 40 C4 8E 21

0x03 00 00 1E 01 1D 00 72 51 D0 1E 20 6E 28 55 00 C4

0x04 8E 21 00 00 1E 01 1D 80 D0 72 1C 16 20 10 2C 25

0x05 80 C4 8E 21 00 00 9E 8C 0A D0 90 20 40 31 20 0C

0x06 40 55 00 C4 8E 21 00 00 18 4E 1F 00 80 51 00 1E

0x07 30 40 80 37 00 BC 88 21 00 00 18 00 00 00 00 -1

0x000x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B0x0C0x0D 0x0E 0x0F


0x01 1 3 80 46 27 78 EA D9 B0 A3 57 49 9C 25

0x02 11 49 4B A5 6E 0 31 40 45 40 61 40 D1 C0 1 1

0x03 1 1 1 1 1 1 2 3A 80 18 71 38 2D 40 58 2C

0x04 45 0 C4 8E 21 0 0 1E 1B 21 50 A0 51 0 1E 30

0x05 48 88 35 0 BC 86 21 0 0 1C

0x06 0 0 0 FD

0x07 0 32 4B 1C 43 0F 0 0A 20 20 20 20 20 20 1 -2

0x00 2 3 21 F1 4E 2 11 1 3 12 13 4 14 5 21 1F

0x01 20 22 10 23 9 7 7 83 1 0 0 65 3 0C 0 10

0x02 0 1 1D 0 BC 52 D0 1E 20 B8 28 55 40 C4 8E 21

0x03 0 0 1E 1 1D 0 72 51 D0 1E 20 6E 28 55 0 C4

0x04 8E 21 0 0 1E 1 1D 80 D0 72 1C 16 20 10 2C 25

0x05 80 C4 8E 21 0 0 9E 8C 0A D0 90 20 40 31 20 0C

0x06 40 55 0 C4 8E 21 0 0 18 4E 1F 0 80 51 0 1E

0x07 30 40 80 37 0 BC 88 21 0 0 18 0 0 0 0 -2

- 11 -

* Before AV ADC Calibration, should be executed the “Tool option 1”

5. Select method of Tool option 11) Press ADJ Key in the Adjust remote control.2) Select “Tool option 1” by using D/E (CH+/-) key, and press

A(ENTER).

3)Select “Maker” by using D/E (CH+/-) key, and change themodule maker and. applied module classification by usingF/G (VOL+/-).

4) Select “Inch” by using D/E (CH+/-) key, and change themodule according to the inch of model.

5) Select “Tool” by using D/E (CH+/-) key, and change thetool name according to the model.

(Inch of model : 26”, 32”, 37”, 42”, Applied module under theclassification)

6) After changing the Tool option 1, push the EXIT Key.

6. ADC Calibration

<Caution>- System control RS-232 Host should be “PC” for adjustment.- Before AV ADC Calibration, execute the “Module selection”.

6.1. Adjustment of RF/AV/S-VIDEO(1) Required Equipments

- Remote controller for adjustment- MSPG-925FS Pattern Generator (Which has Video

Signal: 7 Color Bar Pattern shown in Fig. 1)=> Model: 202 / Pattern: 65

(2) Method of Auto RF/AV/S-VIDEO Color Balance.1) Input the Video Signal: 7 Color Bar signal into AV3.2) Set the PSM to Dynamic mode in the Picture menu.3) Press IN-START key on R/C for adjustment.4) Press the G(Vol.+) key to operate the set, then it

becomes automatically.5) Auto-RGB OK means the adjustment is completed.

6.2. Adjustment of Component.(1) Required Equipments

- Remote controller for adjustment- MSPG-925FS Pattern Generator (Which has 720p/50Hz

YPbPr output Pattern shown in Fig. 1 )=> Model:215/Pattern: 65

(2) Method of Auto Component Color Balance1) Input the Component 720p/50Hz 7 Color Bar(MSPG-

925FS model: 215, pattern: 65) signal into Component.2) Set the PSM to Dynamic mode in the Picture menu.3) Press the IN-START key on R/C for adjustment.4) Press the G(Vol.+) key to operate the set , then it

becomes automatically.5) Auto-RGB OK means the adjustment is completed.


ADC RF/AV/S-VIDEO Component RGB-PC

MSPG925FS PALJ Model:215 (720P) Model: 60

INPUT SELECT AV3 Pattern:65 (1024*768 60Hz)

Model: 202 (PAL-BGDHI) 720P/50Hz Pattern: 65

Pattern: 65 7 Color Bar

PAL 7 Color Bar

Tool option1 Maker Inch Tool

2060 LPL 32 LT75

<Fig. 1>


- 12 -

6.3. Adjustment of RGB(1) Required Equipments

- Remote controller for adjustment- MSPG-925FS Pattern Generator

(Which has XGA [1024*768] 60Hz 8 Color bar 100%pattern shown in Fig. 1)

(2) Method of Auto RGB Color Balance1) Input the PC 1024x768@60Hz 100% Color Bar (MSPG-

925FS model:60, pattern:65) signal into RGB. (Using D-sub to D-sub cable)

2) Set the PSM to Dynamic mode in Picture menu.3) Press the IN-START key on R/C for adjustment4) Press the G(Vol.+) key operate To set , then it becomes

automatically.5) Auto-RGB OK means adjustment is completed.

* Before White-balance, the AV ADC should be done.

7. White Balance* Test Equipment

Color Analyzer (CA-210/CH.9)-> When you adjust LCD color temperature, on Coloranalyzer (CA-210), you should use Channel 9 which isMatrix compensated (White, Red, Green, Blue revised) byCS-1000 and adjust in accordance with White balanceadjustment coordinate which is specified on the next.

* Color temperature standards according to CSM and ModuleCool : 11,000kMedium : 9,300kWarm : 6,500k

* White balance adjustment coordinate and color temperature

- PC (for communication through RS-232C)-> UART Baud rate : 115200 bps

- Luminance Y AV : upper 150 cd/m2 (Typ : 350 cd/m2)-> Applying to Cool, Medium, Warm mode

* Connecting picture of the measuring instrument (OnAutomatic control)Inside PATTERN is used when W/B is controlled. Connect toauto controller or push control R/C IN-START-> Enter the mode of White-Balance, the pattern will comeout.

* Auto adjustment Map (RS-232C)

* Auto-control interface and directions1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10ux).2) Adhere closely the Color Analyzer ( CA-210 ) to the

module less than 10cm distance, keep it with the surfaceof the Module and Color Analyzer’s Provevertically.(80~100°).

3) Aging time - After aging start, keep the power on (no suspension of

power supply) and heat-run over 15 minutes.- Using ‘no signal’ or ‘full white pattern’ or the others,

check the back light on.

Cool CS-1000 CA-210(CH 9)

x 0.276 0.276±0.002

y 0.283 0.283±0.002

∆uv 0.000 0.000

Medium CS-1000 CA-210(CH 9)

x 0.285 0.285±0.002

y 0.293 0.293±0.002

∆uv 0.000 0.000

Warm CS-1000 CA-210(CH 9)

x 0.313 0.313±0.002

y 0.329 0.329±0.002

∆uv 0.004 0.004

<Fig. 2> Connecting picture (On Automatic Control)

Type LD74A

Baud Rate Data bit Stop bit Parity

115200 8 1 None

Protocol Index Cmd 1 Cmd 2 Data Min Value Max Value

Setting R-Gain_Normal j a 00(00) 128(80)

G-Gain_Normal j b 00(00) 128(80)

B-Gain_Normal j c 00(00) 128(80)

R-Gain_Warm j d 00(00) 128(80)

G-Gain_Warm j e 00(00) 128(80)

B-Gain_Warm j f 00(00) 128(80)

R-Gain_Cool j g 00(00) 128(80)

G-Gain_Cool j h 00(00) 128(80)

B-Gain_Cool j i 00(00) 128(80)

R-Offset_Normal l j 00(00) 128(80)

G-Offset_Normal l k 00(00) 128(80)

B-Offset_Normal l l 00(00) 128(80)

R-Offset_Warm l m 00(00) 128(80)

G-Offset_Warm l n 00(00) 128(80)

B-Offset_Warm l o 00(00) 128(80)

R-Offset_Cool l p 00(00) 128(80)

G-Offset_Cool l q 00(00) 128(80)

B-Offset_Cool l r 00(00) 128(80)

Internal Pattern Signal w b 00 W/B adjustment Start

Internal Pattern Signal w b 10 Internal Pattern use

Internal Pattern Signal w b ff W/B adjustment end

- 13 -

7.1. Manual white Balance - One of R Gain / G Gain / B Gain should be kept on 80, and

others are controlled lowering from 80 1) Press ‘power on’ of the control R/C, set heat run to white by

pressing G, and heat run over 15 minutes. (Set : RS-233Host : PC, Baud Rate : 115200bps, Download : Cortez)

2) Zero Calibrate CA-210, and when controlling, stick thesensor to the center of LCD module surface.

3) Double click In-start key on Controlling R/C and get in‘white balance’.

4) Set test-pattern on and display inside pattern. Control iscarried out on three color temperature, COOL, MEDIUM,WARM. (Control is carried out three times,)

5) When the R/G/B GAIN is 80 on OSD, it is the FULLDYNAMIC Range of the Module. In order to control whitebalance without the saturation of FULL DYNAMIC Rangeand DATA, one of R Gain / G Gain / B Gain should be kepton 80, and other two is controlled lowering from 80.

* Color Temperature: Cool, Medium, Warm1) When R GAIN is set to 80

- Control G GAIN and B GAIN by lowering from 80. 2) When B GAIN is set to 80

- Control R GAIN and G GAIN by lowering from 80.3) When G GAIN is set to 80

- Control R GAIN and B GAIN by lowering from 80.One of R Gain / G Gain / B Gain should be kept on 80,and adjust other two lower than 80.(When R/G/B GAIN are all 80, it is the FULL DYNAMICRange of Module)

8. Scart RGB(DVR) Adjustment Mode* Required Equipments

- Remote controller for adjustment- MSPG-925FS Pattern Generator

(Which has Video Signal : Color Bar Pattern shown in Fig.2)-> Model : 232 / Pattern : 80

1) Input the Video Signal : Color Bar signal into AV1(Using Full Scart Cable)

2) Set the PSM to Dynamic mode in Picture menu.3) Press the IN-START key on R/C for adjustment4) Press the TURBO-PICTURE key on R/C for adjustment5) Press the G(Vol.+) key operate To set , then it becomes

automatically.6) Auto-RGB OK means adjustment is completed.

9. Set information(Serial No & Model name)(1) Setting up like bottom figure (After setting white balance,

this is set)1) Press ADJ Key in the Adjust remocon.2) Select “System Control 2” by using D/E(CH+/-) key,

and press A(ENTER).3) Using Adjust remocon, RS-232 Host & Baud Rate &

Download value change (RS-232 Host:Gprobe, BaudRate:115200bps, Download:Cortez)

(2) Bar-code scanning1) Push the menu button in DTV mode.

Select the STATION -> Diagnostics -> To set

2) Check the Serial Number.


A u t o Co l o r B a l an c e ( Hex )

A u t o- S c a r t RGB T o S e t

R g a i n 16

G g a i n 16

B g a i n 14

Y Ga i n 22

Cb Ga i n 22

C r Ga i n 1A

Res e t T o Se t

S c a r t RGB ( D VR) NG

G

G


- 14 -

1. No Power

(1) Symptom1) Does not minute discharge at module. 2) Non does not come into the front LED.

(2) Procedure check

Is the power cord plugged in? Plug in the power cord.

Yes

No

Is the Line Filter and PowerBoard Cable connected?

Connect the Cable.

Yes

No

Is the appropriate Fuse(F100) onthe Power Board?

Replace the Fuse.

Yes

No

Is the Power Board and 13P ofVSC Board Cable connected?

Connect the Cable.

Yes

No

After removing the cables, connect them to the Power Board(except theSC101 connection cable), and change the AC voltage marking to manual.When ST-BY 5V does not operate, replace the Power Board.

TROUBLESHOOTING


- 15 -

2. Protect Mode

(1) Symptom1) After lighting up once, it does not discharge

minutely from module.2) The rely falls.(there is an audible “click”) 3) The color of the front LED turns from green to red.

(2) Procedure check

Is the Power Boardnormal ?

Replace the Power Board.Is the output Low/High voltage normal

except for Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace the connector.After connecting each connector do

they operate normally?

No Yes

Yes

Is the VSCBoard normal?

Is the output voltage normal afterremoving P900, P901 of VSC Board?

If it operates normally after removing theP900, P901 : Replace the VSC Board

No Yes

Does minutedischarge at Module?

Is the LVDC cablenormal?

Is the inverter on?

Check the LCD ModuleYes

No

YES

Yes

Reconnect the LVDScable in P1901

No

Is the IC700(FLI8548)Output normal?

Replace the VSC.No

Replace VSC board.Is it ok?

YES YES

NoIs the Low/High output voltagenormal except for stand-by 5V?

No Replace the Powerboard

Is the voltage (P900 5pinon VSC) 0V or Low?

No

3. No Raster

(1) Symptom1) No OSD and image occur at screen. 2) It maintains the condition where the front LED is green.

(2) Procedure check


- 16 -

4. In case of strange screen display in specific modes

4-1. In case of no OSD display

(1) Symptom1) LED is green.2) The minute discharge is continuously accomplished from the module.

(2) Procedure check

Is the LVDS cablenormal ?

Is the VSC Boardnormal?

Is the LVDS cableconnected?

Insert the Cable.Yes

No

No

Yes

Does the FIL8548IC(IC700) operate?

Replace the FIL8548IC(IC700)

No

Is the Ctrl Board ofModule normal?

Replace the Ctrl B/D.No

No

YesReplace the VSC B/D.

Replace the cable.Yes


- 17 -

4-2. In case there is no display on the screen in specific modes

(1) Symptom1) There is no screen display from a specific input mode.

(RF, AV, Component, RGB, DVI).

(2) Procedure check1) Check the all input modes have normal display.2) Check the video(main)/ data(sub), video(main)/ video(sub) have normal

displays from the PIP mode or DW mode(re-check it/ swap).

(3) In case of an unusual display in RF mode

(4) In case of an unusual display in side S-video/ AV mode

(5) In case of an unusual display in Component, RGB mode

Is the Tuner normal?

Is the CXA2069Q normal?

Is the Tuner Cable connected?

Re-insert the cableYes

No

No

Yes

Is the FIL8548 normal?

Replace the Tuner.

No

Are the Input voltage, IIC Communicationand CVBS output normal?

Yes

Are the Input voltage, IICCommunication and HV sync normal?

NoReplace the IC.

No

Are the input voltage, IICCommunication and HV sync normal?

NoBlock A

Replace the IC.No

Is the Video input of theAV Jack(P1400) normal?

Yes

Is the CXA2069Q normal?

Check the input source.No

Are the Input voltage, IICCommunication and HV sync normal?

NoReplace the IC.

No

Yes

Same as Block A

Are the R,G,B input and H,VSync of the J1100 normal?


Yes

Same as Block A


- 18 -

(6) In case of an unusual display in HDMI mode

(7) In case of an unusual display in SCART1 mode

(8) In case of an unusual display in SCART2 mode

Is the HDMI002(IC1004)normal?

Yes

Same as Block A

Are Input voltage, IIC Communicationand HV sync normal?

No

Is the Video input of theA/V Jack(J1200) normal?

Yes

Same as Block A


Replace the IC.No

Is the Video input of theA/V Jack(J1201) normal?

Yes

Same as Block A



- 19 -

5. In case of no sound

(1) Symptom1) LED is Green.2) Screen display appears but there is no sound.

(2) Procedure check

Is there no sound forAll input(modes)?

Is there no soundonly for HDMI?

No

Yes

Downloadthe EDID data.

Check the signal afterCAX2069 refer to circuit diagram

No

Is there no sound onlyfor specific input?

(except HDMI,DTV,RF)

Check the signal beforeCAX2069 refer to circuit diagram

No

YES YES

Is there no soundonly for RF?

Check the TunerIN/OUT.

No

YES

YES

Is there no sound onlyfor AV/ component/

PC input?

Is the output ofCXA2069 normal?

No

YES

Is the IC1300operating normally?

Replace the IC1300.(MSP4450)

No

Is the IC1301operating normally?

Replace the IC1300.(STA335BW)

No

YES

Replace the VSC B/D.

YES

NoReplace the CXA2069

Is the speaker on?Set on speaker on in

menu.

No

Is the speaker Cablenormal?

Check the SpeakerCable.

No

Yes

- 20 -

6. DVR Function

6-1. Time shift Mode

(1) Symptom1) Doesn’t work time shift mode.2) Can’t enter to recorded list.3) Can’t record AV/RF.

(2) Procedure check


No

Change time shiftmode form off to on.

No

Is time shift modeon Menu?

Are the cables connectedwell?(P1500, P1501)

Insert cables well.

Yes

Power and Data Cable isnormal?(P1500, P1501)

Change the power andData cable.

No

Is HDD normal? Change the HDD Assy.No

No

YES

Check BU9580KVT IC(IC1504).Is it ok?

Replace STI5100 IC(IC100).

YES

Yes Power’s operation isnormal?

No Power’s operation isnormal?

Yes

NoCheck STI5100 IC(IC100),NEC61151F(IC1600),NEC64015A(IC1901).Is it ok?

Replace STI5100 IC(IC100)NEC61151F(IC1600)NEC64015A(IC1901).

YES

Replace VSC Board.

YES

- 21 -

6-2. Time shift sound and Recorded video sound

(1) Symptom-> Sound doesn’t come out.

(2) Procedure check


Is it DVR Mode (timeshift or recorded TV)?

Go on 19page in the document.

Yes

No

MUTE key on? Turn off the mute key.Yes

No

Sound cable is ok?

No

No

No

Connect speak cablesound is ok?

Are power cableconnected well.

Connect powercables/ power B/D.

No

Check speakers.Are they ok?

No

No

Check MSP(IC1300),Audio AMP(IC1301)Is it ok?

Is Data cable(P1501) ok? Connect Data cable.Yes Yes Yes

Change the speakers.Yes

Change the ICs.Is it ok?

Replace VSC B/D.

No

Yes

- 22 -

6-3. Recorded video

(1) Symptom-> Can’t play the recorded video.

(2) Procedure check


Check data cable(P1501).Is it ok?

Connect data cable(P1501).

Remove the recorded lists and Recordone more time and Play again.Is it ok?

No

YesYes 1

Are the cable connected well?(P1500, P1501)

No

Connect cable well.

No

Check STI5100 IC(IC100), NEC61151F(IC600)NEC64015A. Is it ok?

No

Change HDD.Is it ok?

Check BU9580KVT(IC1504).Is it ok?

Yes 2

Replace VSC B/DNo

No


- 23 -

BLOCK DIAGRAMR

x0/1

,Tx0

/1

SC

L/S

DA

H/V

(RG

B)

SC

L/S

DA

Rx0

/1/2

/C±

ST

32

32

C

24

LC

02

24

LC

02

CX

A2

06

9Q

A/V

Sw

itch

A/D

∞‚ø

ÎT

un

er

TU

_M

ain

ST

HD

MI0

02

HD

MI

MU

X

RG

B_

PC

/DT

V

Co

rte

z P

lus

- M

ain

CH

. D

eco

din

g

- 3

D C

om

b

- 3

D D

e-i

nt.

- S

calin

g &

FR

C

- G

UI

- A

ud

io D

ela

y -

CP

U

/ 8

I2C

IR_

inR

S2

32

_R

x/T

x

Sid

e-A

V B

’D

AV

S-A

VY

Cin

3

Fla

sh(4

MB

)

PC

_A

ud

io

SIF

AV

in3

LR

CK

/MC

K SC

K/S

DA

L_

SP

K_

ou

t

R_

SP

K_

ou

t I2

S

Co

mp

on

en

t In

Sca

rt_

RG

B /

FB

Ma

in V

or

YC

LV

DS

_3

1P /

Tx0

/1/2

/3/C

±D

isp

_E

nS

CL

/SD

A

V_

ou

t1Y

_in

1

Su

b V

or

YC

,

DV

R V

or

YC

I2C

I2C

Fo

r D

DC

_R

GB

Fo

r D

DC

_D

VI I2

C

RG

B(P

C/D

TV

)

HD

MI

2(P

C/D

TV

)

RS

23

2

Sca

rt1

Sca

rt2

RF

PC

_Aud

io

MN

T_

ou

t (C

VB

S/L

/R)

AV

in1

(C

VB

S/L

/R/S

cart

_ID

)

TV

L/R

ou

t

TC

74

LC

XR

S2

32

_S

T

DV

R L

R

DV

R S

cart

RG

B

DT

V 6

56

TV

Vo

ut

TV

Vo

ut

DT

V_

ou

t (C

VB

S/L

/R)

TC

74

LC

X1

57

LR

CK

/MC

K SC

K/S

DA

I2S

DT

V I

2S

HD

MI

I2S

TC

74

LC

X1

57

SP

DIF

ou

tS

T S

PD

IF

MS

P S

PD

IF

DD

RR

AM

(2

56

MB

)

DT

V_

ou

t (C

VB

S/L

/R)

MS

P4

45

0K

Au

dio

SW

& T

on

e C

on

tro

lA

V_

LR

PC

_A

ud

ioC

om

p_

LR

in

TV

_L

/Ro

ut

SIF

ST

A3

33

W

TV

_L

/Ro

ut

AV

_L

R

uP

D6

40

15

Vid

eo

D

eco

de

r

24

.57

6M

HY

57

V1

61

61

0E

T

SD

RA

M(2M

B)

uP

D6

11

51

MP

EG

En

cod

er

65

6 C

om

p

CS

53

31

I2S

IN

MC

LK

16

bit

32

bit

HY

57

V6

41

62

0E

T

SD

RA

M(8M

B *

2)

HY

57

V6

41

62

0E

T

ST

m5

10

0T

P D

ec.

Mp

eg

De

cod

er

Au

dio

De

c.

74

LC

X5

41

Ad

dr/D

ata

Bu

ffe

rF

or

Ho

t Plu

gg-i

n

CI

SL

OT Tu

ne

r T

S1

CI

TS

74

LC

X5

41

74

LC

X1

57

74

LC

X3

73

74

LC

X3

73

74

LC

X2

45

74

LC

X5

41

MU

X

Lo

gic

s fo

r C

I

74LC

X32

74LC

X08

74LV

C14

PC

MC

IA

Po

we

r S

wit

ch

TP

S20

11

74

LC

X5

41

74

LC

X5

41

A/D

∞‚ø

ÎT

un

er

TD

FC

-G1

06

P

27

MH

zV

CX

O

HY5DU121622-D43

DDR SDRAM(64MB)

S29JL064H70TFI010

Flash(8MB)

LMI BUS16bit

FMI BUS16bit

FM

I B

US

16

bit S

Tm

51

00

FM

I B

US

16

bit S

Tm

51

00

AT

A T

o S

AT

AC

on

vert

er

HD

D

FM

I B

US

16

bit

ST

m5

10

0

RS

23

2_

Co

rte

z

DTV_out (CVBS/L/R)

DTV 656

DTV I2S

24

C2

56

I2C

_0 3

2.7

68

KH

z2

7M

Hz

74

LV

C1

4

DT

V R

ese

tF

rom

CO

RT

EZ

RS

23

2_

ST

ST

-Co

nn

ect

(2

0p

in)

Tu

ne

r T

S

8

Mp

en

c_T

S

TS

0

I2C

TS

1

SY

S R

ST

I2C

DV

R O

pti

on

$5

4.5

$7

$0

.5$

2.1

$2

$0

.95

$1

0

Dig

ita

l on

lyT

un

er

TD

FG

-G1

05

P

74

LC

X5

41

74

LC

X5

41

74

LC

X1

57

MU

X

Tu

ne

r T

S0

1. IDTV DVR


- 24 -

BU9580

FMI_DATA[ 0- 15]Buf fer

ATA_DATA

Buf ferFMI_AFMIREQFMIGNT

ATA_AATA_DIOWATA_DIOR

HDD(SATA)

TXP/ TXNRXP/ RXN

UPD64015dec oder

UPD61151encoder

656_DATA

DVR_V/ Y OUT

DVR_C OUT

SCART1_DVR_R/ G/ B

SCART1_DVR_FB

SDRAM2MB

SDRAM8MBSDRAM

8MB

CS5331A 5331_SDATA5331_SCLK5331_LPRK

SCART_AUDIO L/ R

MPENC_SDR_DMPENC_SDR_A

VDEC_SDR_DVDEC_SDR_A

MPENC_TS_D[ 0- 7]MPENC_TS_CLKMPENC_TS_SYNCMPENC_TS_TS_VAL

TDFG- G107P

74LCS157IC601IC602IC603

FE_TS0_Data[ 0- 7]FE_TS0_DATA_CLKFE_TS0_DATA_SYNCFE_TS0_DATA_VAL

TS0_Data[ 0- 7]TS0_DATA_CLKTS0_DATA_SYNCTS0_DATA_VAL

LRCLK_5100

SCLK_5100[ DTV]

SPDIF

PCMDATA_5100[ DTV]

Resistor

Tr

STI5100

LDBA[ 0:1] (Bank Selec t )LDDQM[ 0:1] (Data I/ O Mask)LDDQS[ 0:1] (Data Strobe)LDCS/ (Chip Selec t )LDRAS/ (Latc h Row Address Strobe)LDCAS/ (Latc h Co lumn Address Strobe)LDWE/ (Write Enab le)LDCLKE(Cloc k Enab le)LDCLK(Cloc k)LDCLKN(Inverted Cloc k)

TS0_DATA[ 0 :7]TS0_DATA_CLKTS0_DATA_VALTS0_DATA_SYN YUV_D[ 0 :7]

YUV_PIXCLK

CI_EN/

CI_RST

I2C_SDA0/ SCL0

I2C_SDA1/ SCL1

Array R

DIGIT_D[ 0 :7]CLK_DIGIT

EEPROM

TS_SEL/

DTV_AUDIO_MUTE

PIO_286

PIO_287TrREC_B

FOR SCART PIN8

OUT_LEFT

OUT_RIGHT

CVBSBuf fer

Buf fer

DTV_LOUT

DTV_ROUT

SP_CVBS

DTV_AUDIO_MUTE_BUF(ST5100 GPIO)

27M

32.768KhzSystem t ime to be preserved when main power is d isc onnec ted

CPU_WAIT(Wait input(Read/ Write c yc le)

FMIGNT(DVB- CI/ Cab le Card I/ O read Strobe)FMIREQ(DVB- CI/ Cab le Card I/ O wri te Strobe)

IRQ1

FMIWE/ (Read not write)FMICS3/ (Chip selec t)FMICS1/ (Chip selec t)FMIBE1/ (Byte enab le)

Flash(8M)

DDR(512Mbit )

LDA[ 0:12]LDD[ 0:15]

FMI_A[ 1:25]FMI_D[ 0:15]

CXA2069

DTV/ MNT_LOUT

DTV/ MNT_ROUT

DTV/ MNT_VOUT

MUTE_LINE_DTV(Cortez GPIO)

LRCLK_DTV

SPDIF_STI_OUT

SCLK_DTV

PCMDATA_DTV

Array R

IRQ2

FMILBA/ (Flash devic e load burst address/ DVB- CI Cab le Card Write Enab le)

FMIOE/ (Output enab le/ DVB- CI Cab le Card output Enab le)

DVRMPENC_TS__D [ 0 :7]MPENC_TS__CLKMPENC_TS__VALMPENC_TS__SYNMPENC_RESET_ST

2. DVR

3. STi5100 composition


- 25 -

74LCX157MUX

TS_SEL

74LCX157MUX

74LCX157MUX

From D- tuner FE_TS1_DATA

Desc rambled TSTS1_DATAA

B

L AH B To STi5100

74LVC5413statebuf f er

74LVC245Transc eiver

With d irec t ion3state

74LVC5413statebuf f er

TS_SEL_CIL ->

->->

->->

->->

->->

->->

->enab le

H d isab le

FMI_D

FMICS1

D_T/ R (d ir)

74LCX373Latc h

74LCX373Latc h

CI_CS

FMI_A

CI_LATCH

L B inputH A input

A

B

L enab leH Z

L enab leH Z

L previousH enab le : FMI_A = CI_ADDR

CI_TS_DATA

Desc rambled TS

CI_ADDR

CI_DATA

From D-tuner FE_TS1_DATA

Sc rambled TS

From D-tuner FE_TS_DATA

Sc rambled TS

Des

cram

ble

rD

escr

amb

ler

CIM

od

ule

smar

tca

rdin

terf

ace

Mic

rop

roce

sso

rCI_TS_DATA

Desc ramb led TS

Sc art1

Sc art1

Sc art2

Sc art2 cxa2069qc xa2069q

MSP4450KMSP4450K

TV_L/ R out(3,1p in)

DTV/ MNT_LROUT(3,1p in)

Scart1_Lrin(6,2p in)

CompJ1200CompJ1200

PC-aud ioJ1100

PC-aud ioJ1100

PC_AudioLR

Comp_Rin/ Lin

Av2J1201Av2

J1201

Side AV P1400

Side AV P1400

AV2_Lin/ Rin

Lin5/ Rin5

AV_L/ R out

ANX9021ANX9021

STi5100STi5100

DTV_LoutDTV_Rout

74LCX157MUX

74LCX157MUX

33

33

DVB/ PALTuner

TDFC-G106P

DVB/ PALTuner

TDFC-G106P

DVB/ PALTuner

TDFC-G106P

DVB/ PALTuner

TDFC-G106P

SIFAM-AudioFor SECAM

TS1

uPD61151Enc oder

uPD61151Encoder

JM20330SATA Bridge

JM20330SATA Bridge

TS1

FMI_BUSDATA 16b it

MC33078MC33078

CS5331ADC

CS5331ADC

DVR_L/ R

33

HDDHDD

STA333WAMP

STA333WAMP

33

SPDIF_MSP

SPDIF_STI

SPDIF OUTJ400

SPK_L_OUT3pin wafer

SPK_R_OUT4pin wafer

Analog Signal

I2S

SPDIF

SIF

MCLK

4. CI slot composition

5. i-DTV PVR AUDIO PATH


- 26 -

STx5100CUC

TU600A/ D TUNER

IC103(24LC256- I)

I2C_SCL0 / I2C_SDA0

0XAA

2.7K

3V3

IC1901UPD64015

FE_SCL0

FE_SDA0

VDEC_SCL

VDEC_SDA

TU601Dig ital tuner

I2C_SCL1 / I2C_SDA1 2.7K

3V3

FE_SCL1

FE_SDA1

CortezPlus

TU600A/ D tuner

SW_TU_SCL / SW_TU_SDA

SDA_5V / SCL_5V

IC1300(MSP4450k)

IC1400CXA2069Q

4.7K

5.0V

SDA / SCL 4.7K

P_3.3V

IC1301(STA335BW)

0X38

P801,P1901(PDP PANEL)

IC407(LM75)

SDA_EEPR / SCL_EEPR 4.7K

IC702HDCP EEPROM

IC701_24LC256(NVRAM)

3.3V_CTZ

SDA_HDMI / SCL_HDMI 4.7KIC1004

STHDMI002A

+5VST

IC1002AT24C028

J1000HDMI JACK

SDA_HDMI_0 / SCL_HDMI_0

DDC_SDA_0 / DDC_SCL_0

IC1002AT24C028

J1000HDMI JACK

SDA_HDMI_1 / SCL_HDMI_1

DDC_SDA_1 / DDC_SCL_1

47K+5VST

47K+5VST

0X80 0X90

0X94

0XA8

0XC2

6. DVR Board I2C composition

- 27 -

MEMO


- 28 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved. Only for training and service purposes

300

200

700

59170

1

592

590

12053

0

210

580

522

520

521

400

600

800

581

900

150

EXPLODED VIEW

LV

1

A21

A2

Many electrical and mechanical parts in this chassis have special safety-related characteristics. Theseparts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components asrecommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

Aug., 2007Printed in KoreaP/NO : MFL39435601

lg lcd ld74a 32lt75

Documents

special safety parts

exposedmetallic parts

mechanical parts

high temperature parts

replacement parts list

product safety

ac plug prongs

ac source