lg floor standing-type air conditioner - sears parts direct• staple your receipt to this page in...

website http://www.lgservic _

LG Floor Standing-TypeAir ConditionerOWNER'S MANUAL

thoroughlyonditioner.

ture reference after

FOR YOUR RECORDSWrite the model and serial numbers here:

Model #

Serial #

You can find them on a label on the side of each unit.

Dealer's Name

Date Purchased

• Staple your receipt to this page in the event you need it

to prove date of purchase or for warranty issues.

READ THIS MANUALInside you will find many helpful hints on how to use and

maintain your air conditioner properly. Just a little

preventive care on your part can save you a great deal

of time and money over the life of your air conditioner.

You'll find many answers to common problems in the

chart of troubleshooting tips. If you review our chart of

Troubleshooting Tips first, you may not need to call for

service at all.

PRECAUTION• Contact the authorized service technician for repair or

maintenance of this unit.

• Contact the installer for installation of this unit.

• The air conditioner is not intended for use by youngchildren or invalids without supervision.

• Young children should be supervised to ensure thatthey do not play with the air conditioner.

• When the power cord is to be replaced, replacementwork shall be performed by authorized personnel onlyusing only genuine replacement parts.

• Installation work must be performed in accordancewith the National Electric Code by qualified and

authorized personnel only.

2 Floor Standing-Type Air Conditioner

Sa_Precaufions

To prevent injury to the user or other people and property damage, the following instructionsmust be followed.

• Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness isclassified by the following indications.

F

, WARNING CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage.

• Meanings of symbols used in this manual are as shown below.

Be sure not to do.

Be sure to follow the instruction.

ILWARNING- • Installation

• There is risk of fire or electricshock.

• Do not disassemble or repair theproduct. There is risk of fire orelectric shock.


• Improper wiring or installationmay cause fire or electric shock



Owner's Manual 3

SafetyPrecautions


• There is risk of fire, electricshock, explosion, or injury.

• Moisture may condense and wetor damage furniture.

• There is risk of fire or electricshock. jj ,

• There is risk of fire, electricshock, explosion, or injury.

• It may cause injury, accident, ordamage to the product.

• Sharp edges could cause injury.Be especially careful of the caseedges and the fins on thecondenser and evaporator.

• Operation


• If the base collapses, the airconditioner could fall with it,causing property damage,product failure, and personalinjury.

• There is risk of fire or electricalshock.



• There is risk of fire and electricshock.

Safety Precautions

• It may cause There is risk of fire,failure of the product, or electricshock.

• Do not use the telephone or turnswitches on or off.

There is risk of explosion or fire

• There is risk of physical injury,electric shock, or product failure.

• There is risk of fire or electric shock.

• There is risk of fire or failure ofproduct.

• There is risk of electric shock orfire.

i _ •


• Oxygen deficiency could occur.

• There is risk of property damage,failure of product, or electric shock.

• There is risk of fire, electric shock,or product damage.

• There is risk of electric shock.

Owner's Manual 5

SafetyPrecautions

• There is risk of product damage or failure, orunintended operation.

• Installation

• Low refrigerant levels may causefailure of product.

• It may cause a problem for yourneighbors.

• This could result in personal injury and productdamage.

CAUTION

• A bad connection may causewater leakage.

• Avoid personal injury.

• To avoid vibration or water

leakage.

• It may cause corrosion on theproduct. Corrosion, particularly onthe condenser and evaporator fins,could cause product malfunction orinefficient operation.

• Operation

• This could harm to your health. • There is risk of

damage orloss of property.


• It may cause product failure.

Sa_Precaufions

• There is risk of fire, electric shock,or damage to the plastic parts ofthe product.

• There is risk of personal injuryand failure of product.

• It is not sanitary and could causeserious health issues.

• A dirty filter reduces the efficiencyof the air conditioner and couldcause product malfunction ordamage.

• They may burn or explode.

• Becarefulandavoidpersonalinjury.

• Thechemicals in batteries couldcause burnsor other healthhazards.

• There is risk of personal injury.

• There are sharp and moving partsthat could cause personal injury.

• There is risk of fire or explosion

i

• Thechemicals in batteries couldcause burnsor other healthhazards.

@

Owner's Manual 7

PriortoOperation

1. Contact an installation specialist for installation.

2. Plug in the power plug properly.3. Use a dedicated circuit.

4. Do not use an extension cord.

5. Do not start/stop operation by plugging/unplugging the power cord.

6. If the cord/plug is damaged, replace it with only an authorized replacement part.

1. Being exposed to direct airflow for a long time may be hazardous to your health. Do not exposeoccupants, pets, or plants to direct airflow for a long time.

2. Due to the possibility of oxygen deficiency, ventilate the room when using the appliance together withstoves or other heating devices.

3. Do not use this air conditioner for non-specified special purpose (e.g. preserving precision devices,food, pets, plants, or art objects). Such use may damage your properties.

1. Do not touch the metal parts of the unit when removing the filter. Injury can occur.

2. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation,leading to electric shock.

3. When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at avery high speed during operation. There is a possibility of injury if the unit's power is triggered whilecleaning inner parts of the unit.

For repair and maintenance, contact your authorized service dealer.

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that may cause harm to theair conditioner.

This symbol indicates special notes.rAv[*) l [o]:;


OperatingInstructions

1. Design for cooling

2. Super energy efficiency

3. Micom control

4. Whisper quiet operation

5. Wireless remote control

6.3 cooling speeds

7. Removable air filter

8. Anti-Bacteria filter

9.3 minutes delay circuit

Air Outlet

Remote SignalReceptor

Air Intake Vent--

Vent

-- Air Intake Vent

(Rear)

Piping

Owner's Manual 9

Operating Instructions

7 9 6 2 1

8 11 10 4 3

1. START/STOP BUTTON

Operation starts when this button is pressedand stops when the button is pressed again.

2. OPERATION MODE SELECTIONBUTTON

Used to select the operation Mode.

3. ROOM TEMPERATURE SETTINGBUTTONS

Used to select the room temperature.

4. INDOOR FAN SPEED SELECTIONUsed to select fan speed in three steps-low,High, Super High.

5. FAN OPERATION LAMP

6. COOLING OPERATION LAMP

7. SOFT DRY OPERATION LAMP

8. OUTDOOR UNIT OPERATION LAMP

9. AUTO OPERATION LAMP

10. OFF TIMER OPERATION LAMP

11. TURBO-Z OPERATION LAMP



t#

IBIlTIME

0 LG

Operation Mode

0

O

]Flip-updoor

(closed)

I! Cooling Operation ] ._

1AutoOperation ] _.

!Soft Dry Operation ] (_)

O START/STOP BUTTONOperation starts when this button ispressed and stops when the button ispressed again.

ROOM TEMPERATURESETTING BUTTONSUsed to select the room temperature.

INDOOR FAN SPEEDSELECTORUsedto select fan speed in 3 steps low,high,super high.

TURBO-ZUsedto start or stopthe speedcooling. (Speed coolingoperatessuper highfan speed in cooling mode.)

AUTO AIRFLOWDIRECTION CONTROLBUTTONThehorizontallouversswing upand down.

TURBO-Z

Wireless Remote Control Puts all functions at your fingertips

Handling the remote control

• Aim at the signal receptor on the floor standing type air conditioner when operating.

• The remote control signal can be received at a distance of up to about 7meters.

• Be sure that there are no obstructions between the remote control and the signal receptor.

• Do not drop or throw the remote control.

• Do not place the remote control in a location exposed to direct sunlight, or next to a heating unit, or other heatsource.

Owner's Manual 11


O ON/OFF TIMER BUTTONS oNG OFFUsed to set the time of starting andstopping operation.

TIME SETTING BUTTONSUsed to adjust the time.

TIMER SET/CANCEL BUTTONSUsed to set the timer when the desired SET_'_CANCELtime is obtained and to cancel the Timer 0

operation.

Q IMPLE OFF TIMER SET ®BUTTONEach time the button is pressed, the modeis changed in the following process.Time set (1, 2, 3, 4, 5, 6, 7 hurs)If you select "0" the off Timer function willbe cancelled.

O ENERGY SAVING OPERATION ®BUTTON (Not Available)

_1 °C _ °F SWITCHING BUTTON °C/°FUsed to switch temperature reading fromCentigrade to Fahrenheit and viceversa.

_ ESET BUTTONUsed prior to resetting time or afterreplacing batteries.

o RESET

O NDOOR FAN OPERATION +BUTTONUsed to circulate the room air without

coolingor heating (turns indoor fan on/off).

_! PERATION MODE _AoSELECTION BUTTONUsed to select the operation mode.

AUTO AIRFLOW DIRECTIONCONTROL BUTTONThe vertical louvers swing right and left.



1. How to mount onto a wall

Use the screws to secure the holder to the wall or attach the holder side of indoor unit.

2. To insert the remote control to the holder.

Insert

<

How to insert batteries

1. Remove the cover from the back of theremote controller.

• Slide the cover according to the arrowdirection.

2. Insert two batteries.

• Be sure that the (+) and (-) directions arecorrect.

• Be sure that both batteries are new.

3. Re-attach the cover.

• Slide the cover into back position.

• Do not use rechargeable batteriessuch batteries as different from

standard dry cells in shape,dimensions, and performance.

• Change the batteries with a newone if the remote control does not

work properly after using for anextended length of time.

"FLIP TYPE" Remote controller which deliver along with the Set, Can't adjust with spaceprovided inside the Inlet Grill.

Owner's Manual 13

Operating Instructions

• Each time the Operation Mode Selection Button is pressed, the Operation Mode is shifted in the arrow direction.

/

Cooling Operation Auto Operation Soft Dry Operation

Open the door on the remote control.Each time the button is pressed, the operation mode is shifted inthe direction of the arrow.

C_m _ o _ FIL-'_F

•11111| _ ,u

Cooling Auto Soft Dry

• Each time the Fan speed Button is pressed, the Fan speed is shifted in the arrow direction.

Low High Super High

LI ...I. ....] ...,,,,,,YJ.Fan speed is on Low. Fanspeed is onHigh Fan speed is on Supel High



I Press the Start/Stop Button.

Pressthe Operation Mode Selection Button.Press the Operation Mode Button on the remote controller.Select Cooling Operation.

Set the temperature lower than the room temperature.The temperature can be set within a range of 60°F-86°F by 1°F.

) -- TO raise the temperature r

J___ _ -- Zo lower the ternperature / ,-,-,oFkJ _ _ / ,c

| nmIII .

Setthe Fan Speed.

ilI C_) & C_: _ Low High Super High

•,, , _ ......-,, .....;#,,,/-[3 Each time the Fan Speed Button is pressed, Fan speedison Low. FanspeedisonHigh Fan speed ison SuperHigh

the Fan Speed mode is shifted in the arrowdirection.

Owner's Manual 15


Pressthe Start/Stop Button.

Press the Operation Mode Selection Button.Press the Operation Mode Button on the remote controller.Select Soft Dry Operation.

1 Set the temperature lower than the room temperature.The temperature can be set within a range of 60°F~86°F by I°F.

# _ -- To raise the temperature I "_ 617-1 °FIC##1



%

Press the Operation Mode Selection Button.Press the Operation Mode Button on the remote controller.Select Auto Dry Operation.

Set the temperature upper or lower than the standard temperature.The temperature can be set within a range of - 2'~2 by 1 level.

...... I , '-,

0 __B

I ColdCool Proper

(This indication will be shifted to the initial Auto Mode Display state after 4 seconds.'

L

Warm Hot

raise the temperature. _ _ _, To lower the temperature._.J/

During Auto Operation _It is impossible to switch the indoor fan speed because of being already set to the best conditioner _

Owner's Manual 17


I Pressthe Start/Stop Button.

Press the TURBO-Z button to operate the speed cooling mode and the unit will operate insuper high fan speed in cooling mode.

,_,HHIIIIII

No oosE_0 C_EL'c'_ i sE_¢) C_ELc_

During the TURBO-Z function at any moment, the A!C starts to blow the cool air at extremely highspeed setting the room temp. automatically to 65°F. It is especially used to cool the room. in theshortest time in a hot summer.

In heat pump mode or neuro fuzzy mode however, the TURBO-Z function is not available.



I Pressthe Start/Stop Button.

Press the Operation Mode button and Low temperature setting buttons simultaneously for 3seconds.

The unit will respond with beep.

After 3 second,it will shift

Press °C, _°F Switching Button.

IC#1111# xlllll

Owner's Manual 19


Press Fan Operation Button. ']

3

I ressthe Start/Stop Button.

r 1

j,-,÷', ®_'_

(Operation will start when the button is pressed,and stop when the button is pressed again.)

Press this button to makethe vertical louver auto

swing in right and leftdirections.

Press this button to makethe horizontal louver auto

swing in up and downdirections.



7

Pressthe Timer Button. /

Q @ 3 _ /• If you press the button, the selected off timer is displayed as follows; --

: -*,-'-* 3-* _' -* S --*S _ 7'4.>

When you finish the Off Timer setting, the Timer indicator lights off. ]

_ 4 sA::rnds _ _ _ 4 sA::rnds _l

Owner's Manual 21


I ress the fan speed button and High temperature setting buttons simultaneously for 3 seconds.The unit will respond with beep.

During Child Lock Operation

O Whenever you press any Button, it will immediately display

" L-L ", which means Button is Locked.e All the Button on the indoor unit will not work.€ But the Button on the remote controller will work.

For releasing child lock OperationPress the fan speed button and High temperature setting buttons simultaneously for 3 seconds.The unit will respond with beep, Child Lock Operation will removed.

After pressing After 3 seconds,the buttons it will shiftit will shift

immediately

'nA(Ua[eOtherep°Sw%rB_mes°n again after a p°wer failure' Aut° Restarting Operati°n is the functi°n t° 1



Setting the Time

O imecan be set only when you have pressedthe Reset button. If you have just replaced thebatteries, the Reset button should be pressedto reset the time.

Press the Start/Stop button.

_1 ress the Time Setting buttons until the

desired time is set.

Press the Timer SET button. SET

Note: Check the indicator (:_)for A.M. and P.M.

Delay Start/Pro-Set Stop

Make sure the time is set correctly on theremote control display.

lPress the ON/OFF Timerbuttons to turn Timer on or off.

ON _ OFF

O ress the Time Settingbuttons until the desiredtime is set.

O ress the selected on/off setting by SE_pressing the Timer SET button whileaiming the remote control at the signalreceptor.

To cancel the setting the timer.Press the Timer Cancel button while

CANCELaiming remote control at the signal

_ eceptor.(The timer lamp on the air conditioner andthe display will go out.)

NOTE: Select one of the following four types of operation.with the unit runninq

L r_r_ TIME I _ I IrI_ITIME I J IWSITIME _TIME I ] I'I_ITIME _ir_'_TIME I J............,2o 1 I 320 .....3001 _ ......3301Delay OFF Timer Delay ON Timer Delay OFF and O1'4Timer Delay O1'4and OFF Timer

Owner's Manual 23

CareandMaintenance

CAUTION: Before performing any maintenance, turn off the main power to the system.

Removethe Air Filter.Take hold of the tab and pull slightlyforward to remove the filter.

Clean.• To remove the dust adhering to thefilters, either use a vacunm cleaner, orwash them in water and dry in theshade.

• Re-insert the filter to the originalposition.

• Don't wash with water.

• Wipe with a soft dry cloth.

trical ")

• Water hotter than 104°F.Could cause deformation and/or discoloration.

• Volatile substances.

Could damage the surfaces of the airconditioner.


CareandMaintenance

Operate the air conditioner at thefollowing settings for 2 to 3 hours.• Type of operation • Cooling.• Temperature setting : 86°F.

This will dry out the internal mechanisms.Remove the batteries from the RemoteControl.

Turn off the circuit breaker.

_/'_ CAUTION

Turnoff thecircuitbreakerwhentheairconditioneris notgoingtobe usedfora longtime.Dirtmaycollectandmaycausea fire.

Clean the air filters, re-insert, thenoperate the air conditioner.

Be sure that nothing obstructs the airoutlet and intake vents.

This isnot goodforyour healthandwasteselectricity.

Avoidopeningdoorsand windowsas muchas possibleto keepthecoolair inthe room.

Do not letdirectsunshineentertheroomwhenthe air conditioneris in

operation.

Blockagesin the air filter reducetheairflowand lowercoolinganddehumidifyingeffects.Cleanat leastonceeverytwo weeks.

Adjusttheverticaland horizontalairflowdirectionto ensurea uniform

temperatureinthe room.

Sincewindowsarekeptclosed,it isa good ideato openthem andventilatethe roomnowand then.

Owner's Manual 2E

Beforeyoucallforservice...

Check the following points before requesting repairs or service.... If the fault persists, please contact yourdealer or service center.

Case Explanation See page

Doesnotoperate.

The room has a peculiarodor.

It seems that condensation is

leaking from the airconditioner.

Air conditioner does notoperate for about 3 minuteswhen restarted.

Does not cool effectively.

• Haveyou made a mistake in timer operation?

• Hasthe fuseblown or has the circuit breaker been

tripped?• Is the powerSwitch at Off?• Is the unit at the starting of HeatingOperation?

If yes, Hot-start isactivating.• Is the unit in the Deicing?

If yes, wait for finishing the Deicing.

• Checkthat this is not a damp smell exuded by thewalls, carpet, furniture, or cloth items in the room.

• Condensationoccurs when the airflowfrom the airconditionercools the warmroom air.

• This is the Protection deviceof the air conditioner.

• Wait about three minutes and operationwill begin.• If the airflow begins before its temperaturebecome

warm, it will cause an undesiredcooling effect. Inorderto preventthis, the airflow will not begin untilit is sufficientlywarm.

• Is the air filter dirty? See air filter cleaninginstructions.

• The room mayhave been very hot when the roomair conditionerwas first turned on. Allow time for itto cool down.

• Hasthe temperaturebeen set incorrectly?• Are the indoor unit'sair inlet or outlet vents

obstructed?

• For a noisethat sounds likewater flowing.-This is the sound of freon flowing insidethe airconditioner unit.

• For a noisethat sounds likethe compressedairreleasinginto atmosphere.-This is the sound of the dehumidifyingwater beingprocessed insidethe air conditioningunit.

The air conditioner operationis noisy.

24


Celsius(°C)_ _ Fahrenheit (°F) Convert Table

oc oF oc oF0 32 26 781 33 26 791 34 27 802 35 27 812 36 28 823 37 28 833 38 29 844 39 29 854 40 30 865 41 31 876 42 31 886 43 32 897 44 32 907 45 33 918 46 33 928 47 34 939 48 34 949 49 35 95

10 50 36 9611 51 36 9711 52 37 9812 53 37 9912 54 38 10013 55 38 10113 56 39 10214 57 39 10314 58 40 10415 59 41 10516 60 41 10616 61 42 10717 62 42 10817 63 43 10918 64 43 11018 65 44 11119 66 44 11219 67 45 11320 68 46 11421 69 46 11521 70 47 11622 71 47 11722 72 48 11823 73 48 11923 74 49 12024 75 49 12124 76 50 12225 77

Owner's Manual 27

Memo


lg floor standing-type air conditioner - sears parts direct• staple your receipt to this page in...

Documents