level measurement for bulk solids & liquids catalog engl 2013 rev 1.pdf · continuous level...

• Point Level • Continuous• Profile Scanning • Weight• Inventory Control • Wireless

CUSTOM ENGINEERING & INTEGRATION SOLUTIONS

LEVEL MEASUREMENT for BULK SOLIDS & LIQUIDS

Continuous Level Measurement for Solids

Other products for level measurement and detection of bulk solids:• Dust Detectors • Dry Products Flow / No Flow Detector • Tilt Switches• Aeration and Airbrator Nozzles • Pressure and Diaphragm Level Switches • Ultrasonic Level Sensors

• Measures solids, powders, slurries and liquids • Approved for hazardous locations • No field calibration or adjustment • Trouble free mounting and installation • Minimal contact with stored material

The Bin Master SmartBob II cable displacement (yoyo) sensor is a rugged as well as an economical and compact inventory tracking system that has been designed to measure solids and powders in silos and tanks. The powerful and robust design of the SmartBob II provides years of maintenance-free service in vessels up to 180 feet.

Bin Master Smart Bob II Level

BinMaster 3DLevelScannerThe BinMaster 3DLevelScanner uses non-contact, dust-penetrating technology to provide unsurpassed bin volume accuracy. Unlike single point devices, it works by measuring multiple points within the bin. Its unique 3D mapping capabilities provide a visual representation of bin contents, detecting cone up or down as well as sidewall build up.

• Dust-Penetrating Technology: The acoustical-based, low frequency technology is unaffected by dust • Multiple Point Accuracy: Taking measurements from multiple points versus a single point takes into account variations that can occur on material surfaces • Non-Contact Measurements: Appropriate for foods, chemicals and pharmaceuticals as there is no risk of moving parts coming into contact with bin material • 3 dimensional graphic display of silo level profile • True volume reading, even in very large silos

Aysix Silo Weigh Strain CellsTurn your silo in to a scale.Aysix Silo Weigh strain cells are non-intrusive, bolt-on, fully temperature-compensated, reliable, repeatable, accurate and continuous sensors for weight and level measurement in silos.

They clamp on the outside of a silo leg or beam support and measure the deflection in microns that will vary with the product weight.

• Complete silo weight/level measuring solution • Intelligent electronics that provide direct weight or level measurement • Easy bolt on installation • System accuracy of 2% FS for silo weight measurement • Perfect alternative to load cells • No need to lift silo, bolts directly on the side of the leg of a silo

Bin Master BMRX Rotary Level SwitchBin Master rotary switches offer a cost effective means to prevent bin overflows. The BMRX and MAXIMA+ feature low power consumption, "de-engergized" operation - which shuts down the motor when material is present - and automatic alerts to power failure. Many configurations, paddles etc. are available to handle most applications.

Bin Master Capacitance Level Switch

Bin Master Vibrating Probe Level SwitchBin Master provides a variety of vibrating rods to offer side and top-mount flexibility for high, low and mid-level configurations. They are available in standard, extended length, high temperature and mini models. They may be side or top mounted.

BinMaster Particulate MonitorThe BM-30 LX is a particulate monitoring device designed for general process and environmental monitoring of dust particulates for baghouse filter leak detection, process particulate flow monitoring and continuous emissions monitoring. Particulate monitoring helps companies meet regulatory requirements by detecting leaks before emissions are visible.


Aysix Radartronj Moisture Sensor

Level Switches & Accesories for Bulk Powders

Bin Master PROCAP I & II capacitance probes offer interference-free, fail-safe operation & "Quick-Set" calibration. These capacitance sensors are used for high and low level detection in bins, silos, tanks, hoppers, chutes and other vessels used for material storage or process manufacturing. Many probe configurations, materials and lengths are available to handle most applications.

The RadarTron accuratly measures the moisture content of fine aggregates such as sand and crushed stone. RadarTrons microwave technology eleim inates the errors associated with resistance and capacitance technolgies guaranteeing an accurate reading everytime. It is easily installed in any Bin wall and is suitable for digital display or interface with a PLC.

The Micro TREK guided microwave level transmitter is designed for continuous measurement of conductive and non conductive liquids, pulps and solids. The Micro TREK level gauge operates on the well known TDR (Time Domain Reflectrometry) principle. Typical applications will include cement, limestone, fly ash, alumina, carbon black, mineral powders, free flowing solids.

Nivelco TDR Guided Wave Radar

• Universal device that can measure level of liquids, pastes, granulates, powders, and liquid interface • Easy to install: onsite calibration is not needed • Optional second current output - used for displaying interface measurements. • Measuring range up to 24 meters.

The Bin Master SmartBob II cable displacement (yoyo) sensor is a rugged as well as an economical and compact inventory tracking system that has been designed to measure solids and powders in silos and tanks. The powerful and robust design of the SmartBob II provides years of maintenance-free service in vessels up to 180 feet.

• Measures solids, powders, slurries and liquids • Approved for hazardous locations • No field calibration or adjustment • Trouble free mounting and installation • Minimal contact with stored material


Nivelco Non Contact Radar

The Nivelco 24 GHz (K-band) PiloTREK Pulse Radar gauges are regarded the most progressive non-contact level transmitters of the industrial process automation field. Their accuracies are excellent and their short and narrow antennas make their installation simple and low cost. NIVELCO’s new K-band radar featuring ±3 mm (0.12 inch) accuracy and short dead band excels with its versatile housing concept lining up plastic, aluminium and stainless steel versions.

EchoTREK ultrasonic transmitters offer the best in liquid level measurement in a compact simple package. Developed using the established SenSonic range of narrow beam angle pulse echo transducers, EchoTREK units are available with measurement ranges up to 25 meters - with standard plastic, PTFE or stainless steelsensor faces. Installed on the tank roof, or above the liquid level surface to be measured, the transmitter gives an analogue output proportional to liquid level.

• 2-wire K-band Pulse Burst Radar • 23 metre (75 feet) measuring range for liquids and slurries • Easy installation due to small antennas • System accuracy of ± 3 mm (0.12 inch) accuracy • Horn and enclosed antenna types • High temperature version

• Non-contact level metering-wire • 2- or 4-wire compact transmitter • Easy installation due to small antennas • Narrow 5° beam angle • PP, PVDF, PTFE, stainless steel or foam faced transducers • Optional switching relay

Nivelco Non Contact Compact Ultrasonic Sensors

Nivelco Non Contact Integrated Ultrasonic Sensor

Continuous "Non Contact" Level Measurement for Liquids


Continuous "Contact" Level Measurement for Liquids

Nivelco Magnetorestrictive

NIVOTRACK magnetostrictive transmitters are an ideal solution for high accuracy measurement of clean fluids. Its high precision renders the NIVOTRACK suitable for custody transfer measurement of liquids such as fuels, solvents, alcohol derivatives etc.

Nivelco Hydrostatic Pressure Sensors

NIVOPRESS DT series is a 2-wire microprocessor controlled pressure and level gauge. The loop powered transmitter can be converted into indicator by the use of theplug in display module. The unit measures the hydrostatic pressure and for level gauging it compares the water head with the actual atmospheric pressure.The piezoresistive sensor is protected by a flush diaphragm with silicon oil between the two for pressure transfer.

• 0.1 mm or 1 mm resolution • Rigid or flexible guide tube • Insertion length maximum 15 m •Plastic coated version for chemicals •4-20 mA and HART output • 99 point linearization table •Custody transfer measurement

Nivelco Hydrostatic Bore Hole Pressure Sensor

The Nivopress N hydrostatic level transmitters are designed to measure the level of clean or contaminated liquids. The pressure sensor at the bottom of the probe measures the sum of the hydrostatic pressure (Phydr) of the liquid column above it and the atmospheric pressure (Patm). The atmospheric pressure is led to the sensor through a breathing capillary which is equipped with a moisture filter that prevents the moisture reaching and damaging the electronics. This enables the atmospheric pressure to be subtracted from the measured pressure to get the hydrostaticpressure which is proportional to the height of the liquid column (h).

• Non-contact level metering-wire • 2- wire compact transmitter • Measuring range: 1.45-5800 psig, -14.5 psig • Scalable analogue output • Wide variety of process connection • High accuracy <0.25%

•Measuring range up to 200m • Two- or three-wire submersible transmitter • Stainless steel body •Clean or contaminated water, sewage • Weak acids, caustics


• Non-contact level metering-wire • 2- or 4-wire compact transmitter • Easy installation due to small antennas • Narrow 5° beam angle • PP, PVDF, PTFE, stainless steel or foam faced transducers • Optional switching relay

Continuous "Contact" Level Measurement for Liquids

Capacitance Level Transmitter

Capacitive level transmitters provide an ideal solution for level measurement of conductive or non-conductive liquids. The probe of the instrument and the reference probe (which can be either the metal wall of the tank or installed separately) operate as opposing plates of a capacitor. Between the plates of this capacitor the air is replaced by a medium with greater dielectric constant than the air during filling the tank, therefore the capacitance is changing directly proportional to the level. The incorporated electronic circuitry measures the capacitance differenceand converts it to an output signal proportional to level.

• 2-wire loop powered compact transmitter • Rod or cable probes up to 65 feet • Fully or partly insulated probes • Microprocessor based • Nema rated, Alu, SS, PVC and exp proof housings available • High temperature versions

Bypass level indicators are for pressurized vessels up to 3.5 m heightcontaining liquids. The welded bypass chamber that is the body of the indicator and the tank form one pressurized system. Mounted on suitable connection flanges located on the side of the tank the liquid level in the bypass tube and the tank is equal. A float in the bypass tube incorporating a polarized magnet tracks the level of the liquid. Bi-coloured magnetic flaps mounted on the tube composing a bar are serving as visual indicators by changing their colour as the float passes.

Bypass Level Indicators

The MicroTREK guided microwave level transmitter is designed for continuous level measuring of conductive or nonconductive liquids, pulps and solids. MicroTREK level gauge operates based on the well known TDR (Time Domain Reflectometry) principle. Micropulses are sent along a probe guide at the speed of light. As soon as the pulse reaches the surface of the medium, it is reflected back to the electronic module. Level distance is directly proportional to the flight time of the pulse. The reflected signal is dependent on the dielectric constant of the material, the feasibility of the measurement

• Measures solids, powders, slurries and liquids • Accuracy: ± 5 mm (0.2 inch) • Rod, cable and coaxial probes • Trouble free mounting and installation • Explosion proof models

Nivelco TDR Guided Wave Radar


Level Switches for liquids

NIVOSWITCH vibrating fork level switches are suitable for level detectionof liquids or granular, powdered solids. Configurations are available in extended length models as well as compact versions. Also available are sanitary models for food and pharmaceutical service.

Conductivity Level Switches

Conductivity level switches, based on the conductivity principle, can be applied to liquids with conductivity higher than 10 μS/cm. For detecting the level, probes are immersed intothe tank. These probes (and the tank wall if conductive) serve as contacts of an electric circuit. Probes can be of single or multiple rod versions. A maximum of 4 proberodscan fit in the multiple probe with an additional reference probe if tank wall is not conductive.

NIVOMAG MK-200 series magnetic float level switches are used for point level detection and level control of liquids in all types of vessels. The measurement principal is a non contact coupling system is realised by the permanent magnet of the float placed in the tank that can activate the microswitch situated in the housing mounted on the outside. The great variety of both the top and side mounted versions makes it easy to install the switch in any tank at any location.

Nivelco Magnetic Displacer Level Switch

Nivelco Vibrating Fork Level Switch

RF Capacitance level switches are available in a number of configurations from compact, remorte electronics, and rugged inductriasl versions. Theyt are available in dual point detection and available in a wide variety of materials. Our switches are microprocessor based and available witrh a wide variety of connections.

Float Level SwitchesOur float level switches use a hermetically sealed reed contact actuated by a magnet in a float. As the float rises or falls, the magnetic field causes the switch inside the stem to open or close indication an alarm condition. They are available as single float as well as multi float point level switches with a maximum of 4 floats. Mounting configurations for horizontal as well as vertical mounting are available. Materials for both the stem and float are available in SS, brass, PTFE as well as many other materials.

Capacitance Level Switch

Compact Capacitance and Conductive Level SwitchThese miniature and compact level switches are high quality sensors, which can be used in harsh environments, for liquid level limit detection in metallic and non-metallic tanks containing electrically conductive and non-conductive liquids. The probe, fitting and housing are constructed of stainless 316, the isolator is Teflon. They feature built-in protection against reverse polarity, overvoltage and electrical shielding to deliver long-term reliability. The output is relay SPDT which can be configured as either NO or NC or both NO and NC.

Suspension type Float Level switch Level SwitchThe nivofloat type floating level switches are suitable for level switching of various liquids, sewage in shafts, tanks, basins and sumps. These float type level switches featuring mercury free contacts are suitable for drinking water, waste water and polluted liquids. The double chamberred float and sealingf of the cable provide a hermetically sealed reliable switch.

LEVEL FLOW PRESSURE

TEMPERATURE

ANALYSIS

WEB CONNECTIVITY

WIRELESS

SERVICE

RENTALS

ENGINEERING &INTEGRATION

ENCODERS, CONTROLLERS & DISPLAYS

Cancoppas MississaugaPhone: (905) 569-6246 or (800) 595-0514 Fax: (905) 569-6244 2595 Dunwin Dr., Unit #2, Mississauga, ON L5L 3N9

Cancoppas Québec LtéeTéléphone: (514) 697-4202 Télécopieur: (514) 697-6292880 Ave Selkirk, Pointe-Claire, QC, H9R 3S3

[email protected]

Complete Solutions:We have expertise in small solution providing projects, to large multimillion dollar projects. With an experienced team, Cancoppas can handle engineering, software solutions, the right product fit to promote reliable and trouble free operation, and the integration into your existing operation. Just a small example, here is how we can help:

• Tank Farm Inventory Control, with real time local area networks, automatic report generation and more • Wireless Solutions for robust, reliable and cost effective information transmission • Engineering and integration to make sure your system is efficient, seamless, and problem free

VALVE CONTROL

Short & Long RangeBattery & Solar PoweredDigital ProtocolsSingle & Multi-pointsAnalogue I/OHigh Density I/OValve Position

DensityConductivityInterface LevelTotal Suspended SolidsDissolved OxygenSampling PumpsMulti-Parameter UVResidual ChlorineSamplersTurbiditypH/ORP

GaugeDifferential PressureAbsolute

Area VelocityCoriolisDopplerPositive DisplacementDifferential PressureElectromagnetic FlowmeterPaddle WheelThermal MassTransit TimeTurbineVortexRotameters

MagnetostrictiveUltrasonicRadarMechanical RotaryHydrostaticFloatBOBThermal MassUltrasonic GapCapacitanceLaserVibrating

SwitchesSensorsThermo wellsTransmitters

Positioners (Digital, Electropneumatic, Pneumatic)Feedback Modules (Analog, Mechanical, Proximity, NAMUR)Mounting Kits (Rotary, Linear)

DensityConductivityInterface LevelTotal Suspended SolidsDissolved OxygenFlowLevelWireless

Universal IndicatorsDIN Size ControllersData Aquisition SystemsAnalog IndicatorsData LoggersSignal ConditionersProgrammable EncodersIncremental & Absolute Encoders

Maintenance ContractsOn-site field calibrationBench Repair Shop

Digital ProtocolsSingle & Multi-pointsAnalogue I/OHigh Density I/OSoftwareSMS E-Mail Alerts

Professional Panel DesignPLC ProgrammingDesign and Integration“Turn Key” System

0912

level measurement for bulk solids & liquids catalog engl 2013 rev 1.pdf · continuous level...

Documents