level 1 - iit kanpur
TRANSCRIPT
LEVEL 1
The Quiz will be conducted in two levels LEVEL 1
• This level consist of 25 questions MCQ type (+4 -0) or One word and 5 Fact based questions.
• Each question will be displayed on the screen for sufficient duration, just after which next question will follow.
• All the teams will be provided with an answer sheet. • All the subjective questions must be answered in a word in space given• Negative Marking only in Fact based questions (+4, -2)
LEVEL 2• Clearing Threshold cutoff for L1 is necessary.• Rules and regulations of Level 2 will be disclosed after L1.
1.“Excellence for Everyone” is the tagline of which famous automobile company ?
A) Chevrolet Motor
B) BMW
C) Mercedes-Benz
D) Toyota Motor
2. What is the tension in a rope shown in figure 1 if T1< T2?
C) T2 – T1
B) T2
A) T1
D) Zero
3. The flow through a nozzle is regarded as
C) Isothermal flow
B) Constant pressure flow
A) Constant volume flow
D) Isentropic flow
4. Which of the following symptom is caused as a result
of brake disc run out ?
A) Ineffectiveness of the brakes
B) Judder during braking
C) Localized wearing of the brake pads
D) Rapid wearing of the brake pads
5. The first Indian automobile company is
A. Tata motors limited
B. Hindustan Motors Limited
C. Ashok Leyland
D. Chinkara Motors
6. What refers to the parallel axis theorem for second
moment of area?
A. Mohr’s theorem
B. Steiner’s theorem
C. Maxwell’s theorem
D. Young’s theorem
7. In a ball bearing, ball and bearing forms a
A. Turning pair
B. Rolling pair
C. Screw pair
D. Spherical pair
8.
Talking about extensive properties which one of the following is wrongly placed….
(all terms have their usual meaning)
U, T, V, S, G, H
9. The connecting rod is attached to the piston by the
A. Cap boltB. Gudgeon pin
C. Cap roller bearingD. Rod cap
10. “Digital Twin Spark Ignition” technology is patent of which company?
B) YAMAHA
C) BAJAJ
A) HONDA
D) TVS
11. The temperature of piston will be more at
A) THE PISTON WALLS
B) THE CROWN OF PISTON
C) THE SKIRT OF PISTON
D) THE PISTON PIN
12. Knocking tendency in SI engine reduces with increasing:
A) Compression Ratio
B) Wall temperature
C) Engine speed
D) None
13. In commercial vehicle layouts engine is located
forward, rear or under floor mainly to
A) Better utilization of space
B) Increase fuel economy
C) Better weight distribution
D) Reduce the weight of chassis
14. Which of the following generally drive the oil pump
A) Cam shaft
B) Crank shaft
C) Battery
D) Chain drive
15. If the air-fuel mixture ignites before the spark takes place at spark plug, the condition is called
A) DETONATION
C) RUMBLE
B) IGNITION
D) PRE-IGNITION
16. Identify the given mechanical component
17. Name the car company.
18.The forward transfer of weight to the front wheels result in imbalance of vehicle along Y-axis, this phenomenon is known as
19.If SUV refers to Sports Utility Vehicle, what does CUV refers to
A.Compact Utility Vehicle
B.CrossOver Utility Vehicle
C.Central Utility Vehicle
D.Common Utility Vehicle
20.Identify the component of the steering system.
21.
TO WHICH COMPANY DOES THIS FAMOUS LOGO BELONGS…
22.
IDENTIFY THIS CAR , INCLUDED IN LIST OF WORLD’S 5 FASTEST CARS.
23.
IDENTIFY LOGO
24. First I.C Engine Was Installed In
A. CAR
B. BOAT
C. TRUCK
D. PLANE
25. Identify the component
26.THE TWO MESHED GEAR HAVE GEAR RATIO OF 3:1. EVERY TIME
THE LARGER GEAR TURNS ONCE, SMALLER WILL TURN 1/3 TIMES
SERIOUS JOKING
27.THE DEVICE FOR SMOOTHING OUT THE POWER IMPULSE FROM ENGINE IS CALLED CLUTCH
SERIOUS JOKING
28.THE PORTION OF CRANKSHAFT WHICH RESTS ON CYLINDER BLOCK IS CALLED MAIN JOURNAL
SERIOUS JOKING
29.
“DRIVING IS BELIEVING” IS ONE OF THE TAGLINES OF HYUNDAI
SERIOUS JOKING
30.
The torque available at the contact between driving wheels and road is known as tractive effort.
SERIOUS JOKING