ldf6810 service manual

DISHWASHERSERVICE MANUAL

BEFORE SERVICING THE UNIT, PLEASE READ THIS MANUAL CAREFULLYFOR SAFETY AND CORRECT SERVICES.

NOTE

MODEL : LDF6810WW / LDF6810BB / LDF6810STMODEL : LDF7810WW / LDF7810BB / LDF7810STMODEL : LDF7811WW / LDF7811BB / LDF7811ST

LDS5811WW / LDS5811BB / LDS5811ST

- 3 -

1. CAUTION......................................................................................................................... 4

2. SPECIFICATIONS ........................................................................................................... 5

3. WIRING DIAGRAM........................................................................................................ 6

4. FEATURES & TECHNICAL EXPLANATION ................................................................... 7

5. PARTS NAME................................................................................................................ 16

6. PROGRAM CHART ..................................................................................................... 19

7. HOW TO DISASSEMBLE ............................................................................................ 21

8. TROUBLE SHOOTING METHODS.............................................................................. 30A. TROUBLE SHOOTING ACCORDING TO DISPLAYED ERROR MESSAGE...........30B. TROUBLE DIAGNOSES AND REPAIR BY SYMPTOM........................................... 32

9. INSTALLATION INSTRUCTION ................................................................................... 36

10. EXPLODED VIEW .......................................................................................................43

11. REPLACEMENT PART LIST ........................................................................................52

CONTENTS

- 4 -

DISCONNECT POWER CORD BEFORE SERVICING

RECONNECT ALL GROUNDING DEVICES

IMPORTANT SAFETY NOTICE !

This service information is intended for individuals possessing adequate backgrounds of electrical,electronic and mechanical experience.Any attempt to repair this appliance may result in personal injury and property damage.The manufacturer or seller can not be responsiblefor the interpretation of this information, nor can it assume any liability in connection with its use.

CAUTION !

- 5 -

2. SPECIFICATION

Rated Voltage / Frequency AC 120V/60HzInstallation Built-In

Place Settings 16Product Dimension(in) 23 7/8 x 25 x 33 7/8Product Weight(lbs) 7811/ 7810 series : 115lbs, 5811/ 6810 series : 110lbsDoor Color White, Black, StainlessTub Material Stainless SteelControl ElectronicRated Power(Watt) 1,350Heater Power(Watt) 1,200Programs 7811/ 7810 series : 6, 6810 series : 5Upper Rack Position 7811/ 7810 series : Adjustable, 5811/ 6810 series : manualLower Rack 50% Fold downWater Consumption 21-30 (Normal)Power Consumption(kWh/year) 352~370Operating Time (min) 101-135 (Normal)Fan Dry System YesDelay Start Function YesAuto-Off Power Switch YesProcess Monitor Yes

Wash Level 5

Racks Nylon CoatingOperating Water Pressure (Bar) 20-120 (140-830kPa)

ITEM SPECIFICATION

- 6 -

3. WIRING DIAGRAM

- 7 -

4. FEATURES & TECHNICAL EXPLANATION4-1. Product Features

If you raise the Upper Rack, you can load large dishes in the Lower Rack.(Max. 14 in.)The tall tub provides large dishes loading as well as large capacity.LG dishwashers let you load oversized items in the Lower and Upper Rack.

Newly introduced Slim Direct Inverter motor is inverter-controlled. Speed iscontrolled based on program selection. It also offers high energy efficiency tominimize energy loss.

This is one of the best performance solutions for drying dishes because itminimizes venting humid air to the outside of the dishwasher. In addition, thissystem ensures better drying results compared to the condensing dryingsystem.

Because of alternating water spray between the Upper and LowerRack, the water pressure allows superior performance and reducedconsumption of water and electricity.

For best wash results, the self-cleaning filter system continuously cleans thewater as it circulates. Your LG dishwasher has a self-cleaning filter that grindsfood into small particles before it goes down the drain.

Ultra Big Capacity

Slim Direct Inverter Motor

Hybrid Drying System

Vario Spray System

Self Cleaning Filter

MoistAir

DryAir

MixedAir

toUpperArm

toLowerArm

Soil Sensor

Fine Mesh

to Drain

- 8 -

4-2. Display Panel4-2-1. LDF 7811/7810 Series

PROGRAM

Press the program thatcorresponds to yourdesired wash cycle.

CANCEL

To cancel a runningprogram, open the door,then press and hold theNormal and Delicatebuttons for 3 seconds.

INDICATOR

Child lock: Lamp will turn onwhen Child Lock setting is on.

Rinse Aid: Refill with Rinse aidwhen Lamp turns on.

This program is for very heavily soiled loads including pots,pans and casserole dishes which may have dry food residue.

This program is for very heavily soiled loads

This program is for normally soiled everyday loads.

This program is for washing delicate items like glasses.

This program is for that quick wash of lightly soiled recentlyused dishes and cutlery.

This program is for very lightly soiled loads.

Soak

Normal

Quick Wash

Rinse Only

Delicate

Power Scrub

Control panel may vary on some models.

- 9 -

SPRAY(INTENSITY)

Repeated pressing of theSpray button will selectStrong, Medium orSoft.

DELAY START

If you want to delay the start ofa selected program, press theDelay Start button.

Each press of Delay Start willdelay the start of the cycle byone hour.

The delay start time can beadjusted from 1 to 24 hours inone-hour increment.

HALF LOAD

In case of a small load, use theupper or lower rack only to saveenergy.

Each press of the Half Loadbutton cycles between upperrack only and lower rack only.

If you don't press Half Load,the dishwasher runs normally,i.e, operation of upper andlower spray arm alternatingperiodically.

POWER

For operating, press thisbutton first for power on.

After operating, the powerautomatically switches offfor safety and economy.

In case of an unusual Powersurge or disturbance, thepower may be automaticallyturned off for safety.

CHILD LOCK

Lock the control buttonsto prevent the settingsfrom being changed.

To lock/unlock, pressSpray and Rinsebuttons simultaneouslyfor 3 seconds with dooropen.

SANITARY/EXTRA RINSE

Repeated pressing of theRinse button will selectSanitary, Extra Rinseor both.

If you select the Sanitaryfunction, the temperatureof Heating Rinse canreach 161 (72 ).

When you select ExtraRinse, an additionalrinse cycle is added.

- 10 -

SPRAY(INTENSITY)

Repeated pressing of theSpray button will selectStrong, Medium orSoft.

CHILD LOCK


To lock/unlock, pressSpray and Rinse buttonssimultaneously for 3seconds.





HALF LOAD

In case of a small load, use theupper or lower rack only to saveenergy.

Each press of the Half Loadbutton cycles between upperrack only and lower rack only.

If you don't press Half Load,the dishwasher runs normally,i.e, operation of upper andlower spray arm alternatingperiodically.

4-2-2. LDF 5811 Series

- 11 -

INDICATOR

Child lock: Lamp will turnon when Child Locksetting is on.

Rinse Aid: Refill withRinse aid when Lamp turnson.

PROCESSINGINDICATOR

Current programphase is indicated.

TIME LEFT

Before starting, the display window showsthe running time of the selected program.

After starting, the display window showsthe remaining time.

If the dishwasher has a trouble, the troubletype is displayed.

PROGRAM

Press theprogram thatcorresponds toyour desiredwash cycle.

CANCEL

To cancel arunning program,press and holdthe Normal andDelicate buttonsfor 3 seconds.

DELAY START




POWER




- 12 -

PROGRAM

Press the program thatcorresponds to yourdesired wash cycle.

CANCEL

To cancel a runningprogram, open the door,then press and hold thePower Scrub andNormal buttons for 3seconds.

INDICATOR

Child lock: Lamp will turn onwhen Child Lock setting is on.

Rinse Aid: Refill with Rinse aidwhen Lamp turns on.

This program is for very heavily soiled loads

This program is for normally soiled everyday loads.

This program is for washing delicate items like glasses.

This program is for very lightly soiled loads.

This program is to wash some items loaded on the upper rack.

Normal

Rinse Only

Upper Only

Delicate

Power Scrub

Control panel may vary on some models.4-2-3. LDF 6810 Series

- 13 -

DELAY START




POWER




CHILD LOCK


To lock/unlock, pressDelicate and Rinse Onlybuttons simultaneouslyfor 3 seconds with dooropen.





4-3. TEST MODE4-3-1. LDF 7811/7810 LDS 5811 Series

CHECK PROGRAM

BUTTON The number ofpushing button Front DisplayTop

Display Load and Checking pointsDoor open/

closedRinse + Time Delay +POWER S/WSoakPower ScrubNormalDelicateQuick WashRinse OnlySupplyRinseHalf Load

Time Delay

Normal Water Level : 315Pure Water : more than 229

1 TIME

1 TIME1 TIME1 TIME1 TIME1 TIME1 TIME1 TIME1 TIME1 TIME1 TIME

2 TIME

3 TIME4 TIME5 TIME

6 TIME

7 TIME8 TIME9 TIME

10 TIME

11 TIME

12 TIME

13 TIME

31

32

333435

36

373839

3A

3b

3c

n : 3H/U:023H/U2

112233445566778899

1 : 112 : 223 : 334 : 445 : 556 : 667 : 778 : 889 : 99

Soil Level

n : 02

n : 03Frequency

n : 05

n : 06

n : 07n : 08

Temp. ( )n : 0A

n : 0b

n : 0c

Soil Sensor

Wash Pump

Drain PumpInlet ValveDispenser

Heater(for 10 sec)

Fan

ThermistorLower Nozzle

(VARIO)Upper Nozzle

(VARIO)Wash-Drain-Water Supply

Auto-Off

Delay StartChild Lock +

Rinse AidWashRinseDry

Wash-Rinse-Dry

Strong-SoftSanitary-ExtraUpper-Lower

Soak-Normal

Delicate-RinseOnly

Rinse Aid

All LEDs are lighting Both

All LEDs are lightingAll LEDs are lightingAll LEDs are lightingAll LEDs are lightingAll LEDs are lightingAll LEDs are lightingStrong/Medium/SoftSanitary-Extra Rinse

Upper-Lower

BothBothBothBothBothBothBothBothBothBoth

Closed

ClosedBoth

Closed

Closed

Closed

Both

Closed

Closed

Closed

ClosedSupply water before operating the Test Mode.

- 14 -

Normal Water Level : 295

- 15 -

4-3-2. LDF 6810 SeriesCHECK PROGRAM

BUTTON The number ofpushing buttonTop

Display Load and Checking pointsDoor open/

closedUpper Only + Time Delay +POWERPower ScrubNormalDelicateRinse OnlyUpper Only

Rinse

Time Delay

1 TIME

1 TIME1 TIME1 TIME1 TIME1 TIME

1 TIME

1 TIME

2 TIME

3 TIME4 TIME5 TIME

6 TIME

7 TIME8 TIME9 TIME

10 TIME

11 TIME

12 TIME

13 TIME

31

32

333435

36

373839

3A

3b

3c

3H/U2

1122334455

66

Wash Pump

Drain PumpInlet ValveDispenser

Heater(for 10 sec)

Fan

ThermistorLower Nozzle

(VARIO)Upper Nozzle

(VARIO)Wash-Drain-Water Supply

Auto-Off

Child Lock + Rinse AidSanitary-ExtraPower Scrub +

Normal + DelicateRinse Only + Upper Only

Rinse Aid

All LEDs are lighting

All LEDs are lightingAll LEDs are lightingAll LEDs are lightingAll LEDs are lightingAll LEDs are lighting

All LEDs are lighting

Both

BothBothBothBothBothBothBothBothBoth

Closed

BothClosedClosed

Closed

Closed

Both

Closed

Closed

Closed

Closed

- 16 -

5. PARTS NAME

Control PanelFront DisplayDoor HandleFront CoverLower CoverLeveling FootSide CabinetBaseTop Spray ArmUpper Spray Arm

Removable TinesLower Spray ArmDetergent & Rinse Aid DispenserVapor Vent CoverUpper RackCutlery BasketLower RackTop DisplayPower Button

The appearance and specifications may be varied without notice according to localities.

INSTALL BRACKET WOOD SCREW

5-1. LDF 7811/7810 Series

- 17 -

Control PanelFront DisplayDoor HandlePower ButtonFront CoverLower CoverLeveling FootSide CabinetBase

Top Spray ArmUpper Spray ArmRemovable TinesLower Spray ArmDetergent & Rinse Aid DispenserVapor Vent CoverUpper RackCutlery BasketLower Rack



5-2. LDF 5811 Series

- 18 -

Control PanelDoor HandleFront CoverLower CoverLeveling FootSide CabinetBaseTop Spray ArmUpper Spray Arm

Lower Spray ArmDetergent & Rinse Aid DispenserVapor Vent CoverUpper RackCutlery BasketLower RackTop DisplayPower Button




- 19 -

6. PROGRAM CHART(SCHEMATIC DIAGRAM)

Drain A

2610

1046

1010

3030

4965

72

1810

1038

1010

2630

6368

1010

1030

1020

3060

65

10106

1

2210

2630

4968

86

2020

4660

1030

830

330

W/Motor

Drain Pump

Inlet ValveHeaterVario M

otorFan M

otorDispenserTherm

al ActAuto Off S/W

Program chart

Rinse

Dry

Main W

ashW

ashR

inse 1R

inse 2H

eating RinseD

ry

Program

Wash

Wash

Wash

Rinse

Stop

Stop

Stop

Wash

Wash

Wash

Wash

Wash

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

WashDrain

Drain

Drain

Drain

Drain

Heating AHeating B

Dry

Drain D

Drain

Drain

Drain

Stop

Stop

Drain

Drain

Water Supply

Water Supply

Stop

Drain C

DrainWater Supply

Water Supply

Rinse

Drain

Drain

Drain

Drain

Drain

Drain

Drain

Drain

Drain

Drain B

Drain B

Drain C

Drain

Drain

DrainStop

Drain

Drain

Stop

Pre Wash 1

Pre Wash 2

Pre Wash 3

Drain B

Drain B

Wash

Wash

Wash

Wash

DrainStop

Water SupplyWash

Power Scrub

Soak

Rinse Only

Quick

Delicate

NORMAL

6-1. LDF 7811/7810 LDS 5811 Series

- 20 -

Drain A

1810

1038

1010

2630

6368

1010

1030

1020

3060

65

10106

1

2210

2630

4968

86

2020

4660

1030

830

330

W/Motor

Drain Pump

Inlet ValveHeaterVario M

otorFan M

otorDispenserTherm

al ActAuto Off S/W

Program chart

Rinse

Dry

Main W

ashW

ashR

inse 1R

inse 2H

eating RinseD

ry

Program

Wash

Wash

Wash

Rinse

Stop

Stop

Stop

Wash

Wash

Wash

Wash

Wash

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

Water Supply

WashDrain

Drain

Drain

Drain

Drain

Heating AHeating B

Dry

Drain D

Drain

Drain

Drain

Stop

Stop

Drain

Drain

Water Supply

Water Supply

Stop

Drain C

DrainWater Supply

Water Supply

Rinse

Drain

Drain

Drain

Drain

Drain

Drain

Drain

Drain

Drain

Drain B

Drain B

Drain C

Drain

Drain

DrainStop

Drain

Drain

Stop

Pre Wash 1

Pre Wash 2

Pre Wash 3

Drain B

Drain B

Wash

Wash

Wash

Wash

DrainStop

Water SupplyWash

Power Scrub

Rinse Only

Quick

Delicate

NORMAL


- 21 -

BEFORE DISASSEMBLING THE DISHWASHER ;1) Remove the cord from electric outlet to avoid electric shock.2) Close the Water Tap (faucet).3) Remove all dishes and items in the dishwasher.4) Remove the Lower Rack and the Upper Rack.5) Remove the inlet hose and drain hose connetion to avoid the hose damages.6) Prepare some towels to avoid floor wet by the water left in the dishwasher.

7. HOW TO DISASSEMBLE

7-1. FULL DISASSEMBLE1. Lower Cover and Lower Felt

1) Remove the front 2 screws.2) Pull the Felt.3) Remove the Inlet Hose and Power Supply

Cable.

2. Cabinet and Tub Felt1) Cabinet-R

Remove front 2 screws.Remove rear 3 screws.

2) Cabinet-LRemove front 2 screws.Remove rear 3 screws.

3) Tub Felt

Lower Felt

Lower Cover

Tub Felt

Cabinet-L

Cabinet-R

- 22 -

Control Panel Front Cover

Controller

Controller

Latch Assembly

Front Display

3-1. Door Assembly (LDF 6810/7811/7810 Series)

1) Front CoverOpen the door.Remove 12 screws(stainless).

2) Control Panel AssemblyRemove 2 screws(Stainless).Remove the wire connections.Be sure the wiring should not bechanged in reassemblingRemove the Latch assembly.Remove the Front Display.Remove 8 screws for Controller.

- 23 -

Control Panel Front Cover

Controller

Controller

Latch Assembly

3-2. Door Assembly (LDF 5811 Series)

1) Front CoverOpen the door.Remove 6 screws(Stainless).

2) Control Panel AssemblyRemove 8 screws(Stainless).Remove the wire connections.Be sure the wiring should not bechanged in reassemblingRemove the Latch assembly.Remove 8 screws for Controller.

- 24 -

Fan Assembly

Inner CoverGasket

Flange

Detergent Dispenser

Door Hinge

Air Duct

Door Bracket

Hinge Bracket

Hinge Spring

3) Fan AssemblyOpen the door.Remove 4 screws and a earth screw forDoor Bracket.Remove the wire connetions.Remove the Air Duct.Turn the Inner Cover counterclockwise.

4) Detergent DispenserClose the doorRemove the wire connections.Remove 6 screws with brackets.Push the Detergent slowly pulling up thethe Flange by Standard Screwdriver.

5) Door Spring (Right & Left)Push the Spring upwards and take it offfrom the Hinge Bracket.Be careful not to be injured by thesharpedge of Tub.Take off the Hinge Link from the Hinge.

6) Door LinerOpen the door.Pull the Door Liner and take it off fromthe Hinge Supporter.

Door Liner Assembly

Hinge Supporter

- 25 -

Lead Wire Holer Hook

Lead Wire HolerLower Frame

Drain Hose

Drain Hose Holder

4. Lower Frame 1) Press the holder hook as shown in figure.2) Remove 4 screws.

6. Drain Hose Holder 1) Press the holder hook as shown in figure.2) Pull the Drain Hose and remove the Drain

Hose Holder.

5. Put the Dishwasher upside down.

- 26 -

Base CoverCabinet Base

7. Base Cover 1) Remove 2 screws.2) Pull the Base Cover out.

8. Harness & Hose Assembly 1) Remove the wiring connections.2) Remove the Hose connections from

Sump Assembly.

You can see the information of WiringDiagram at the back of Lower Cover.

- 27 -

Cabinet Base

Inlet ValveCabinet Base

Air BrakerNut

Gasket

Air BrakerAssembly

9. Cabinet Base1) Remove 8 screws.2) Lift it upward.

10. Inlet Valve1) You can disassemble the lnlet Valve by

removing the 2 screws.

11. Air Braker Assembly1) Disconnect the 3 hoses assembly.2) Turn the Air Braker Nut counterclockwise.

Be careful the o-ring should not be lost.

- 28 -

Sump Holder

HookSumpAssembly

1) Heater & Drain MotorPull the Heater out of the Sump afterreleasing the nut.Remove 3 screws.

2) Vario Motor & Soil SensorRemove 2 screws for Vario Motor.Pull the Vario Motor, Soil Sensor andMicro S/W.

Drain Pump

Heater

Vario Motor SoilSensor

Micro S/W

12. Sump Assembly Remove 2 screws.Remove the Sump Holder and push theSump Assembly down with pulling asideHook.Be careful not to drop the SumpAssembly to the bottom.

- 29 -

13. Holder Supporter, Tub Packingand Hinge Supporter Assembly.

When you reassemble the Sump Assembly,be careful not to kink, tear and take off theseals.

You must take off Stopper Roller(F117) by screwdriver to change the Rail Assembly.(Stopper Roller could be broken while youare taking off. So you should be careful notto be hurt and have extra stopper rollersready at servicing at all times)

Rotate the screwdriver, after slide it into thegap between Stopper Roller and Rail Roller.

- 30 -

A. TROUBLE SHOOTING ACCORDING TO DISPLAYED ERROR MESSAGE

ERROR MESSAGE POSSIBLE CAUSE REMEDYFOR ERROR OCCURRENCE

The Water Supply Tap is closed.The Water Supply is shut off.The Inlet Hose is kinked.The Water Pressure is very low.(below 10 psi)Inlet Valve is OK?The filter of Inlet Valve is cloggedby impure water.The Hall sensor is OK?The Impeller of Air Guide is bound.

The Drain Hose kinked or blocked.

Wiring connection is OK?

The drain outlet of sump is

blocked.The Drain Pump/Motor or circuit is

troubled.

Water leakage in Hose connections.

Water is leaked by damages.

The Motor Water Seal leakage of

Sump assembly.The height of Drain Hose connection

(sink-Drain Hose) is not over 20 .

Impeller of the Washing Pump is

worn away.

Remove the cause of kink or block.

Check the wiring connection.

Measure the electric resistance of

Drain Motor. (20-40 )

Replace the Drain Motor or repair

the Circuit.

Replace the connections of Hose.

Check the point of damages and

repair or replace the related parts.Read the Installation Instructions

(page 9) and fix it to therecommended Height.Replace the Impeller of the

Washing Pump.

Take action on Water Supplydevice.

Measure the electric resistance ofInlet Valve. (950-1300 )Clean the filter of Inlet Valve.Check the frequency of Inlet Waterby the Test Mode.Replace the Air Braker.

Not reached to the nor-mal water level in spiteof 10 min. water supply

INLET ERROR

displayed

Condition

Not fully drained out inspite of 5 min. drainoperation

The excessive RPM ofWashing Motorhappened during Washcycle due to waterleakage.

DRAIN ERROR

displayed

Condition

LEAKAGE ERROR

displayed

Condition

8.TROUBLE SHOOTING METHODS

- 31 -

ERROR MESSAGE POSSIBLE CAUSE REMEDYFOR ERROR OCCURRENCE

The Inlet Valve is troubled.

The Controller is troubled.

The Inlet Water Temperature is

very high. (over 194 )


The Thermistor is OK?


The Impeller of Washing Pump is

locked.The rotor of Washing Motor is

locked.The Blade is locked.

Check the temperature. (Test Mode)

If the temperature is displayed,

adjust the Inlet Water

Temperature to 120 .

If the temperature is not

displayed,check the wiring connection.

check the electric resistance

of Thermistor. (11~14k at 77 )

Replace the PCB.

Replace the Inlet Valve.

Repair or replace the Controller.

Excessive water is sup-plied than normal waterlevel.(Automatically drainPump operated.)

EXCESS ERROR

displayed

Condition

The resistance of ther-mistor not normally out put.

THERMAL ERROR

displayed

Condition

Check the wiring connection.

Replace the cause of restriction.

Replace the Washing Motor.

Replace the PCB.

The Motor is workingabnormally.

MOTOR ERROR

displayed

Condition

- 32 -

No Power on when the power button pressed.

The Power connectionis correctly connected.

The Fuse or Circuit Breaker of house is O.K?

The Power Switch or the Circuit is O.K?

Re-connect the Powr connection.

Check the electricity is failed or not.

Replace the Fuse or Circuit Breaker of house.

Check the Power Switch or the circuit and repair it.

Check t he Con t ro l l e r. (Powe r C i r cu i t )

B. TROUBLE DIAGNOSES AND REPAIR BY SYMPTOM

NO

NO

YES

YES

YES

NO

- 33 -

The Wash Pump/Motor does not run.

The Door is tightly closed?

The Wiring connectionsis OK?

The Blade is not locked by a small and sharp object?

close the Door tightly. Check the Door Switch in Latch Handle.

Re-connect the wiring connections related to theWashing Motor.

Remove the cause of lock or replace the Blade.

Replace the Wahing Pump/Motor

NO

NO

NO

YES

YES

YES

- 34 -

Washing Results are not Satisfactory

After washing, are there still White deposits or streaks onthe dishes?

NO

After washing, are there stillfood soils on the dishes?

YES

Check that : - the amount of detergent Correctly used or not- Filters clogged or not.- the holes of spray arms blocked or not.- Utensils are correctly arranged or not.- Utensils are overloaded or not.- the spray arm rotating is obstructed or not.- the program is correctly selected or not.

Reduce the amount of Rinse-Aid(for Streak)

YES

Dry Results are not satisfactory

Increase the amount of Rinse-Aid.(Set the number higher)

Select the Program that the Rinse temperature is higher.

- 35 -

Power Button not automatically off after operation.

Check the button is blocked by foreign materials.

Check the Power Switch.(Replace it, if necessary.)

Check the Controller.(Replace it, if necessary.)

- 36 -

9. INSTALLATION INSTRUCTION

Step 1: PREPARE CUPBOARD OPENING

1. This dishwasher is designed to fit a standard dishwasher opening as shown below.

2. Select a location as close to sink as possible for easy connections to water and drain lines.

3. The dishwasher should not be installed more than 10 ft. (3m) from the sink for properdrainage.

4. If dishwasher is to be installed in a corner, a minimum of 2 in. (50mm) is required betweenthe dishwasher and an adjacent a wall.

Ensure the floor under the dishwasher is at the same level as the rest of the room toallow for any service requirements.

If dishwasher will sit directly onsubflooring, subfloor should besealed with a waterproof paint orsealer to prevent damage fromsteam.

Drill a 1-1/2 (38mm) dia hole or cutout for drain hose, inlet hose andelectrical cables on either side. approx. 4 (100mm, W) X 4 (100mm, H)These openings must be within 4(100mm) from the floor and 1-5/8(40mm) from the back wall. If there isa floor in the cabinet under the sink,it will also be necessary to drill or cutthrough the floor to connect thewater and drain under the sink.

- 37 -

WARNING!For personal safety, remove house fuse or open circuit breaker beforeinstallation. Do not use an extension cord or adapter plug with this dishwasher.Electrical and grounding connections must comply with the national electricalcode/provincial and municipal code and/or other local codes.

Figure A

Step 2: PREPARE THE ELECTRICAL WIRING

1. This appliance must be operated with correct voltage as shown in this manual and on therating plate, and connected to an individual, properly grounded branch circuit, protectedby time delay fuse. Wiring must be 3 wires including ground.

2. The wiring or cord should be in an accessible location adjacent to, and not behind thedishwasher and within 4 ft. (1.2m) of the dishwasher side.

3. The wiring or cord must be grounded properly, if in doubt, have it checked by a qualifiedelectrician. No other appliance shall be connected to the same outlet by a double adapteror similar plug.

4. The wiring or cord must be oriented as shown in Figure A below.

5. Check the dishwasher for any damage before trying to install it.

6. Make sure water line and Electrical line are oriented in the bottom channels as shown inthe figure below.If you find any damage to the dishwasher, Please contact your dealer or builderimmediately.

- 38 -

Step 3: PREPARE THE WATER SUPPLY CONNECTION

1. This dishwasher may be connected to either hot or cold water. If the water can not bemaintained below 149 (65 ), the dishwasher must be connected to cold water.

2. When connecting the dishwasher water line, sealing tape or compound should be used toavoid leaks.

3. When connecting the dishwasher water line, the house supply should be shut off.

4. The Water Supply Tube must be oriented as shown in Figure A on page 6.

Step 4: PREPARE DISHWASHER FOR INSTALLATION

1. Adjust the legs to the required height to fit properly under the countertop as shown below.2. Check the level of dishwasher by using level.

- 39 -

1. Remove the Lower Cover and orient dishwasher as shown below.

2. Before sliding the dishwasher into the cupboard opening, make all necessary heightadjustments using the legs.

3. Slide the dishwasher into the cabinet opening carefully. Make sure that the drain hoseinside the cabinet is not kinked.

4. Follow the instruction as in Figure B.

Step 5: INSTALL THE DISHWASHER IN CUPBOARD

- 40 -

Step 6: DRAIN LINE CONNECTION

1. If the end of the drain hose does not fit to the drain line, use an adapter (not supplied) thatmust be resistant to heat and detergent and may be obtained from a plumbing shop.

2. There are 2 typical connections as shown in Figures C & D.

There may be other options than shown here for connection the drain hose. The drainconnection must meet local plumbing regulations. The S trap spigot must be drilled out cleanly and free of obstruction to its maximuminternal diameter, if used for drainage. To prevent syphoning, one of the following instruction methods must be followed:

Follow local codes and ordinances.

Do not exceed 10 ft. (3m) distanceto drain.

Do not connect drain lines fromother devices to the dishwasherdrain hose.

Drain Requirements

Figure C: Connection to Disposer or waste Tee.

Figure D: Connection to Air Gap.

- 41 -

Step 7: WATER SUPPLY CONNECTION

1. When connecting, sealing tape orsealing compound should beused to avoid water leaks.

2. Before connecting, turn off the watersupply.

3. After fitting the Elbow into theInlet Valve, slide the FlexibleStainless Tube or Copper Tubeinto the Elbow.

4. Tighten the nut and make surethat the line is not kinked orsharply bent.

Inlet Valve

Water Supply Tube

Elbow

1. Before beginning, turn off electricalpower to the unit at the circuit breaker.

2. Remove the Junction Cover and thenInstall the Strain Relief.

3. Twist Wire Connectors tightly on thewires. Wrap each connection withElectrical tape.

4. Check again and make sure that allwires are connected correctly, black toblack, white to white, green to green(ground to ground).

5. Replace the Junction Cover.

Junction Cover

Wire Connector

Junction Case

Strain Relief

black to black

(ground to ground)green to green

white to white

Step 8: ELECTRICAL POWER CONNECTION

- 42 -

Step 9: FINAL CHECKS

1. Turn electrical power back on at the circuit breaker.

2. Turn house water supply back on.

3. Operate the dishwasher through one cycle (Quick cycle is recommended) to check forwater leaks and operating conditions.

4. Replace the Lower Cover.

- 43 -

ACCESSORIES

LDF7810 Series LDS5811 Series

LDF6810 Series

LDF6810 Series*005

LDF7811 Series

10. EXPLODED VIEW

- 44 -

A008

A007

F101

*005

E010

A005

A020

F001

M210

A040

A003 M262

M270

M261

M260

A160

A130

A010

A006

EXPLODED VIEW

- 45 -

M086

F045 F060

F050

F022

M090

F043

F011

F013 F117

F144

F110 F132

F143

F117

F210

F011

F013

M006

M005

F171

F014

F041

F040

F042

For changing F210 or F110, you must change F117 together.(Ref 24page)

EXPLODED VIEW - TUB ASSEMBLY

- 46 -

LDS5811 Serise only

A151

A152

A158

A150

A158

A140A157

A151

A149A144

A147

A148

A141A142

A110

A147

A050F191

A101

A102

A103

A156

A159 A080

F192

F004

F005

A070

A155

A060

A074

A073

EXPLODED VIEW - RACK ASSEMBLY (LDF7811/7810 LDS5811 Series)

- 47 -

A150

A158

A140

A147

A141A142

A157A144

A151 A152

A080

A101

A102

A103

EXPLODED VIEW - RACK ASSEMBLY (LDF6810 Series)

- 48 -

K260

K203

K208

K254

K209

K216

K201

K207

K215

K251

K253

K220

K252

K260

K262

K203

K208

K209

K251

K212

K252K230

K201K217

K216

EXPLODED VIEW - PANEL ASSEMBLY (LDF7811/7810 LDS5811 Series)

- 49 -

K260

K203

K208

K209

K201

K207

K215

K251

K216

K253

K220

K252

EXPLODED VIEW - PANEL ASSEMBLY (LDF6810 Series)

- 50 -

K002

A120

K010

K030

K010

K005

K006 K230K001

K122K110 K121K101

K006

F174

F142

F141

K124

K010

K005

K006K006

LDF7810/LDF6810Series

LDF7811Series

LDF5811Series

K030

K100

EXPLODED VIEW - DOOR ASSEMBLY

- 51 -

M001

M110

M038

M037

M025

M035

M130

M120

M007

M088M034

M220

M060M081

M050

M087

M026

M028M027

M031

M036

EXPLODED VIEW - SUMP ASSEMBLY

- 52 -- 52 -

11. REPLACEMENT PART LIST

*001 MANUAL ASSEMBLY, OWNERS 3829DD3002B 1*002 BOX, CARTON 3890DZ3015A 1*003 MANUAL, SERVICE 3828ED3001X 1*005 ACCESSORY ASSEMBLY 5001DD4001A 1A003 FELT 4766DD2004A LOWER FELT 1A005 BRACKET, TOP 4810DD4002B 4A006 SUPPORTER, HOLDER 4980ED2015A 1A007 SUPPORTER, HOLDER 4980ED2014A 1A008 SUPPORTER, HOLDER 4980ED2018A 1

3090ED1001A 1A010 CABINET 3090ED1001B 1

3090ED1001C 13090ED1002A 1

A020 CABINET 3090ED1002B 13090ED1002C 13551DD2001A 1

A040 COVER ASSEMBLY, LOWER 3551DD2001B 13551DD2001C 1

A050 NOZZLE ASSEMBLY 5249DD1002A LOWER NOZZLE 1A060 NOZZLE ASSEMBLY 5249DD1001A UPPER NOZZLE 1A070 GUIDE ASSEMBLY 4974DD9001A 1A073 WASHER, DRAWING 1WZZDD3001A 1A074 SHAFT, NOZZLE 4370ED3007A 1A080 RACK 3750DD2001A CUP RACK 2A101 DECO HANDLE 3806DD3004A STS 1A102 HANDLE FRONT 3650DD3001A FRONT 1A103 HANDLE REAR 3650DD3002A REAR 1A110 BASKET ASSEMBLY, SPOON 5005DD1001A 1A120 HARNESS, PWB 6877DD1002A 1A130 HOSE ASSEMBLY, DRAIN 5215ED3001E 1A140 RACK ASSEMBLY 3751DD1001A LOWER RACK 1A141 RACK 3750ED1004A 1A142 ROLLER ASSEMBLY 4581DD9002B 8A144 RACK 3750DD2003A 2A147 HOLDER 4930DD3006A 3A148 RACK 3750DD1001A 1A149 RACK 3750DD1002A 1A150 RACK ASSEMBLY 3751DD1002A UPPER RACK 1A151 RACK 3750ED1005A 1A155 GUIDE ASSEMBLY 4975ED2005A RIGHT 1A156 GUIDE ASSEMBLY 4975ED2004A LEFT 1A157 HOLDER 4930DD3003A 4A158 HOLDER 4930DD3005A 3A159 RACK 3750DD2002A 2A160 FILTER ASSEMBLY (CIRC) 6201EC1006A 1

DESC PART No. COMMENTS QTYLOC

LG MODEL: LD-6100WB/BB/TBYOUR MODEL: LDF7811WW/BB/ST

Run_Date : 2005-01-30SPECIFICATION: 120V 60Hz

CAUTION : BEFORE REPLACING ANY OFTHESE COMPONENTS.READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL

NOTE : S(SAFETY PARTS), AL(ALTERNATIVE PARTS)

WBBBSTWBBBSTWBBBST

- 53 -- 53 -

E010 BUSHING 4830ED4001A 2F001 FRAME ASSEMBLY 3211DD1001A 1F004 NOZZLE ASSEMBLY 5249DD2001A TOP NOZZLE 1F005 SHAFT NOZZLE 4370ED3006A TOP NOZZLE 1F011 SPRING, HINGE 4970ED4004A 2F013 CONNECTOR ASSEMBLY 4933DD3001A 2F014 HINGE, BRACKET 4810ED4004A 2F022 SENSOR ASSEMBLY 6501DD2001A 1F040 GUIDE ASSEMBLY 4975DD1001A 1F041 HOSE, INLET 5214DD3001A 1F042 HOSE, CONNECTOR 5214DD3003A 1F043 HOSE, CONNECTOR 5214DD3002A 1F045 COVER, PROTECT 3550DD2001A 1F050 NUT, DRAWING 4020FD3641C 1F060 GASKET 4986DD3001A 1F101 PACKING 3920DD3002A 1F110 RAIL ASSEMBLY 5219DD2002A MUST CHANGE F117 TOGETHER(REF 24P-13) 1F117 STOPPER, ROLLER 4620ED3001A 2F132 PACKING 3920DD3005A TUB PACKING 1F143 HINGE ASSEMBLY 4775ED3004A 1F144 HINGE ASSEMBLY 4775ED3003A 1F171 LATCH, LOCK 4026DD3001A 1F174 BRACKET, HINGE 4810DD1001A DOOR FRAME 1F191 GUIDE, WATER 4974DD2003A 1F192 GUIDE, NOZZLE 4974DD3001A 1F210 RAIL ASSEMBLY 5219DD2001A MUST CHANGE F117 TOGETHER(REF 24P-13) 1K001 DISPENSER 4924FD2123E 1K002 BRACKET ASSEMBLY 4810FD3805A 2

3650ED2006A 1K005 HANDLE 3650ED2006B 1

3650ED2006C 13806ED3008A 2

K006 DECO, HANDLE 3806ED3008B 23806ED3008C 23550ED0001A 1

K010 COVER FRONT 3550ED0001B 13550ED0001C 13551DD1003A 1

K030 COVER ASSEMBLY, FRONT 3551DD1003B 13551DD1003C 1

K100 DOOR LINER ASM 4937DD9001A DOOR LINER + DAMPING SHEET + GASKET 1K110 BLOWER ASSEMBLY 5835ED2002A 1K121 GASKET 4986DD3003A BLOWER GASKET 1K122 COVER, BLOWER 3550ED3011A 1K124 VENT 5232ED2001A 1K141 DOOR HINGE ASSEMBLY 4775DD2001A 1K142 DOOR HINGE ASSEMBLY 4775DD2002A 1

5020ED3008C 6K201 BUTTON, CONTROL 5020ED3008D PROGRAM BUTTON 6

5020ED3008E 63790ED3007A 1K203 WINDOW 3790ED3007D TOP WINDOW 1

PART NAME PART No. SPEC&COLOR Q'tyNo.

WBBBSTWBBBSTWBBBSTWBBBST

WBBBSTWBBB

- 54 -- 54 -

K203 WINDOW 3790ED3007E 1K207 COVER, GUIDE 3550ED3012A 1

3720ED1005A 1K208 PANEL, CONTROL 3720ED1005B 1

3720ED1005C 15020ED3011A 1

K209 BUTTON, POWER SWITCH 5020ED3011B 15020ED3011A 1

K215 COVER, GUIDE 3550ED1009A 15020ED3012C 4

K216 BUTTON, CONTROL 5020ED3012D OPTION BUTTON 43791DD3001E 13846ER1001A 1

K220 MARK, PET 3846ER1001B 13846ER1001A 13791DD3001A 1

K230 WINDOW 3791DD3001B FRONT WINDOW 13791DD3001B 1

K251 PWB(PCB) ASSEMBLY, MAIN 6871DD1006A 1K252 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2001A 1K253 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2002A 1K254 DISPLAY LED ASSEMBLY 6327DC3001A 1K260 LATCH, ASSEMBLY 4027ED3002A 1M001 HOLDER 4930DD3002A 1M005 GASKET 4986DD3002A SUMP GASKET 1M006 SUMP, ASSEMBLY 3485ED1002A 1M007 SUMP 3485DD1001A SUMP+SEAL+GREASE 1M025 VALVE, CHECK 5220DD3001A 1M026 MOTOR ASSEMBLY, WM 4681ED3001B VARIO MOTOR 1M027 SWITCH, MICRO 3W40025C 1M028 CAM, SWITCH 4430ED3001A 1M031 PACKING 3920ED4009B VARIO PACKING 1M034 BLADE 5832DD4001A 1M035 SEAL 4036DD3001A 1M036 HOLDER 4930DD3008A 1M037 FILTER ASSEMBLY, MESH 5231DD1001A 1M038 HOLDER 4930DD3012A 1M050 MOTOR ASSEMBLY, PUMP 4681EA2002D DRAIN MOTOR 1M060 MOTOR ASSEMBLY, WM 4681ED1004A 1M081 HEATER ASSEMBLY 5301DD1001A 1M086 MICRO S/W 3W40025P 2M087 SENSOR ASSEMBLY 6501ED2002D SOIL SENSOR 1M088 PROTECTOR (MECH) 3740ED3003A 1M090 FLOAT ASSEMBLY 4769DD2001A 1M110 FILTER ASSEMBLY, MESH 5231ED1001A 1M120 CASE ASSEMBLY 3111DD1001A 1M130 IMPELLER ASSEMBLY 5911ED3003A 1M210 VALVE ASSEMBLY, INLET 5221DD1001A 1M220 VALVE, CHECK 5220ED4004A 1M260 BASE, CABINET 3040ED1003A 1M261 COVER ASSEMBLY, BASE 3551DD1002A 1M262 CASE 3110DD3002A 1M270 LEG 4778ED3001A 1


STWBBBST

WBBBSTWBBBSTWBBBST

BBWB

ST

- 55 -- 55 -

*001 MANUAL ASSEMBLY, OWNERS 3829DD3002C 1*002 BOX, CARTON 3890DZ3015A 1*003 MANUAL, SERVICE 3828ED3001X 1*005 ACCESSORY ASSEMBLY 5001DD4001A 1A003 FELT 4766DD2004A LOWER FELT 1A005 BRACKET, TOP 4810DD4002B 4A006 SUPPORTER, HOLDER 4980ED2015A 1A007 SUPPORTER, HOLDER 4980ED2014A 1A008 SUPPORTER, HOLDER 4980ED2018A 1

3090ED1001A 1A010 CABINET 3090ED1001B 1

3090ED1001C 13090ED1002A 1



A050 NOZZLE ASSEMBLY 5249DD1002A LOWER NOZZLE 1A060 NOZZLE ASSEMBLY 5249DD1001A UPPER NOZZLE 1A070 GUIDE ASSEMBLY 4974DD9001A 1A073 WASHER, DRAWING 1WZZDD3001A 1A074 SHAFT, NOZZLE 4370ED3007A 1A080 RACK 3750DD2001A CUP RACK 2A101 DECO HANDLE 3806DD3004A STS 1A102 HANDLE FRONT 3650DD3001A FRONT 1A103 HANDLE REAR 3650DD3002A REAR 1A110 BASKET ASSEMBLY, SPOON 5005DD1001A 1A120 HARNESS, PWB 6877DD1002A 1A130 HOSE ASSEMBLY, DRAIN 5215ED3001E 1A140 RACK ASSEMBLY 3751DD1001A LOWER RACK 1A141 RACK 3750ED1004A 1A142 ROLLER ASSEMBLY 4581DD9002B 8A144 RACK 3750DD2003A 2A147 HOLDER 4930DD3006A 3A148 RACK 3750DD1001A 1A149 RACK 3750DD1002A 1A150 RACK ASSEMBLY 3751DD1002B UPPER RACK 1A151 RACK 3750ED1005B 1A152 ROLLER ASM 4581DD9001A 10A157 HOLDER 4930DD3003A 4A158 HOLDER 4930DD3005A 3A159 RACK 3750DD2002A 2A160 FILTER ASSEMBLY (CIRC) 6201EC1006A 1E010 BUSHING 4830ED4001A 2


LG MODEL: LD-6090WB/BB/TBYOUR MODEL: LDS5811WW/BB/ST




WBBBSTWBBBSTWBBBST

- 56 -- 56 -

F001 FRAME ASSEMBLY 3211DD1001A 1F004 NOZZLE ASSEMBLY 5249DD2001A TOP NOZZLE 1F005 SHAFT NOZZLE 4370ED3006A TOP NOZZLE 1F011 SPRING, HINGE 4970ED4004A 2F013 CONNECTOR ASSEMBLY 4933DD3001A 2F014 HINGE, BRACKET 4810ED4004A 2F022 SENSOR ASSEMBLY 6510DD2001A 1F040 GUIDE ASSEMBLY 4975DD1001A 1F041 HOSE, INLET 5214DD3001A 1F042 HOSE, CONNECTOR 5214DD3003A 1F043 HOSE, CONNECTOR 5214DD3002A 1F045 COVER, PROTECT 3550DD2001A 1F050 NUT, DRAWING 4020FD3641C 1F060 GASKET 4986DD3001A 1F101 PACKING 3920DD3002A 1F110 RAIL ASSEMBLY 5219DD2002A MUST CHANGE F117 TOGETHER(REF 24P-13) 1F117 STOPPER, ROLLER 4620ED3001A 2F132 PACKING 3920DD3005A TUB PACKING 1F143 HINGE ASSEMBLY 4775ED3004A 1F144 HINGE ASSEMBLY 4775ED3003A 1F171 LATCH, LOCK 4026DD3001A 1F174 BRACKET, HINGE 4810DD1001A DOOR FRAME 1F191 GUIDE, WATER 4974DD2003A 1F192 GUIDE, NOZZLE 4974DD3001A 1F210 RAIL ASSEMBLY 5219DD2001A MUST CHANGE F117 TOGETHER(REF 24P-13) 1K001 DISPENSER 4924FD2123E 1K002 BRACKET ASSEMBLY 4810FD3805A 2

3551DD1004A 1K010 COVER ASSEMBLY, FRONT 3551DD1004B 1

3551DD1004D 1K100 DOOR LINER ASM 4937DD9001A DOOR LINER + DAMPING SHEET + GASKET 1K110 BLOWER ASSEMBLY 5835ED2002A 1K121 GASKET 4986DD3003A BLOWER GASKET 1K122 COVER, BLOWER 3550ED3011A 1K124 VENT 5232ED2001A 1K141 DOOR HINGE ASSEMBLY 4775DD2001A 1K142 DOOR HINGE ASSEMBLY 4775DD2002A 1

5020DD2001A 1K201 BUTTON, CONTROL 5020DD2001B PROGRAM BUTTON 1

5020DD2001C 13790DD3001A 1

K203 WINDOW 3790DD3001B PROGRESS WINDOW 13790DD3001B 13720DD1001A 1

K208 PANEL, CONTROL 3720DD1001B 13720DD1001C 15020DD2004A 1

K209 BUTTON, POWER SWITCH 5020DD2004B 15020DD2004C 1


BBWB

STWBBBSTWBBBSTWBBBST

WBBBST

- 57 -- 57 -

K212 BUTTON, CONTROL 5020DD3001A DELAY START 15020DD2003A 15020DD2003B 1K216 BUTTON, CONTROL5020DD2003C

OPTION BUTTON1

5020DD2002A 1K217 BUTTON, CONTROL 5020DD2002B PROGRAM BUTTON 1

5020DD2002C 13846ER1001A 1

K220 MARK, PET 3846ER1001B 13846ER1001A 1

K230 WINDOW 3790DD3002A OPTION WINDOW 1K251 PWB(PCB) ASSEMBLY, MAIN 6871DD1006B 1K252 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2003A 1K260 LATCH, ASSEMBLY 4027ED3002A 1

3650DD2005A 1K262 HANDLE 3650DD2005B 1

3650DD2005C 1M001 HOLDER 4930DD3002A 1M005 GASKET 4986DD3002A SUMP GASKET 1M006 SUMP, ASSEMBLY 3485ED1002A 1M007 SUMP 3485DD1001A SUMP+SEAL+GREASE 1M025 VALVE, CHECK 5220DD3001A 1M026 MOTOR ASSEMBLY, WM 4681ED3001B VARIO MOTOR 1M027 SWITCH, MICRO 3W40025C 1M028 CAM, SWITCH 4430ED3001A 1M031 PACKING 3920ED4009B VARIO PACKING 1M034 BLADE 5832DD4001A 1M035 SEAL 4036DD3001A 1M036 HOLDER 4930DD3008A 1M037 FILTER ASSEMBLY, MESH 5231DD1001A 1M038 HOLDER 4930DD3012A 1M050 MOTOR ASSEMBLY, PUMP 4681EA2002D DRAIN MOTOR 1M060 MOTOR ASSEMBLY, WM 4681ED1004A 1M081 HEATER ASSEMBLY 5301DD1001A 1M086 MICRO S/W 3W40025P 1M087 SENSOR ASSEMBLY 6501ED2002D SOIL SENSOR 1M088 PROTECTOR (MECH) 3740ED3003A 1M090 FLOAT ASSEMBLY 4769DD2001A 1M110 FILTER ASSEMBLY, MESH 5231ED1001A 1M120 CASE ASSEMBLY 3111DD1001A 1M130 IMPELLER ASSEMBLY 5911ED3003A 1M210 VALVE ASSEMBLY, INLET 5221DD1001A 1M220 VALVE, CHECK 5220ED4004A 1M260 BASE, CABINET 3040ED1003A 1M261 COVER ASSEMBLY, BASE 3551DD1002A 1M262 CASE 3110DD3002A 1M270 LEG 4778ED3001A 1


WBST

BBSTWBBBST

WBBBST

BBWB

- 58 -- 58 -

*001 MANUAL ASSEMBLY, OWNERS 3829DD3002B 1*002 BOX, CARTON 3890DZ3015A 1*003 MANUAL, SERVICE 3828ED3001X 1*005 ACCESSORY ASSEMBLY 5001DD4001A 1A003 FELT 4766DD2004A LOWER FELT 1A005 BRACKET, TOP 4810DD4002B 4A006 SUPPORTER, HOLDER 4980ED2015A 1A007 SUPPORTER, HOLDER 4980ED2014A 1A008 SUPPORTER, HOLDER 4980ED2018A 1

3090ED1001A 1A010 CABINET 3090ED1001B 1

3090ED1001C 13090ED1002A 1



A050 NOZZLE ASSEMBLY 5249DD1002A LOWER NOZZLE 1A060 NOZZLE ASSEMBLY 5249DD1001A UPPER NOZZLE 1A070 GUIDE ASSEMBLY 4974DD9001A 1A073 WASHER, DRAWING 1WZZDD3001A 1A074 SHAFT, NOZZLE 4370ED3007A 1A080 RACK 3750DD2001A CUP RACK 2A101 DECO HANDLE 3806DD3004A STS 1A102 HANDLE FRONT 3650DD3001A FRONT 1A103 HANDLE REAR 3650DD3002A REAR 1A110 BASKET ASSEMBLY, SPOON 5005DD1001A 1A120 HARNESS, PWB 6877DD1002A 1A130 HOSE ASSEMBLY, DRAIN 5215ED3001E 1A140 RACK ASSEMBLY 3751DD1001A LOWER RACK 1A141 RACK 3750ED1004A 1A142 ROLLER ASSEMBLY 4581DD9002B 8A144 RACK 3750DD2003A 2A147 HOLDER 4930DD3006A 3A148 RACK 3750DD1001A 1A149 RACK 3750DD1002A 1A150 RACK ASSEMBLY 3751DD1002A UPPER RACK 1A151 RACK 3750ED1005A 1A155 GUIDE ASSEMBLY 4975ED2005A RIGHT 1A156 GUIDE ASSEMBLY 4975ED2004A LEFT 1A157 HOLDER 4930DD3003A 4A158 HOLDER 4930DD3005A 3A159 RACK 3750DD2002A 2A160 FILTER ASSEMBLY (CIRC) 6201EC1006A 1






BBWB

WB

WB

ST

BBST

BBST

- 59 -- 59 -

E010 BUSHING 4830ED4001A 2F001 FRAME ASSEMBLY 3211DD1001A 1F004 NOZZLE ASSEMBLY 5249DD2001A TOP NOZZLE 1F005 SHAFT NOZZLE 4370ED3006A TOP NOZZLE 1F011 SPRING, HINGE 4970ED4004A 2F013 CONNECTOR ASSEMBLY 4933DD3001A 2F014 HINGE, BRACKET 4810ED4004A 2F022 SENSOR ASSEMBLY 6501DD2001A 1F040 GUIDE ASSEMBLY 4975DD1001A 1F041 HOSE, INLET 5214DD3001A 1F042 HOSE, CONNECTOR 5214DD3003A 1F043 HOSE, CONNECTOR 5214DD3002A 1F045 COVER, PROTECT 3550DD2001A 1F050 NUT, DRAWING 4020FD3641C 1F060 GASKET 4986DD3001A 1F101 PACKING 3920DD3002A 1F110 RAIL ASSEMBLY 5219DD2002A MUST CHANGE F117 TOGETHER(REF 24P-13) 1F013 CONNECTOR ASSEMBLY 4933DD3001A 2F117 STOPPER, ROLLER 4620ED3001A 2F132 PACKING 3920DD3005A TUB PACKING 1F143 HINGE ASSEMBLY 4775ED3004A 1F144 HINGE ASSEMBLY 4775ED3003A 1F171 LATCH, LOCK 4026DD3001A 1F174 BRACKET, HINGE 4810DD1001A DOOR FRAME 1F191 GUIDE, WATER 4974DD2003A 1F192 GUIDE, NOZZLE 4974DD3001A 1F210 RAIL ASSEMBLY 5219DD2001A MUST CHANGE F117 TOGETHER(REF 24P-13) 1K001 DISPENSER 4924FD2123E 1K002 BRACKET ASSEMBLY 4810FD3805A 2

3650ED2006A/D 1K005 HANDLE 3650ED2006B 1

3650ED2006C 13806ED3008A 1

K006 DECO, HANDLE 3806ED3008B 23806ED3008C 23550ED0001E 1

K010 COVER FRONT 3551ED0001F 13550ED0001G 1

3551DD1001E/H 1K030 COVER ASSEMBLY, FRONT 3551DD1003F 1

3551DD1003G 1K100 DOOR LINER ASM 4937DD9001A DOOR LINER + DAMPING SHEET + GASKET 1K110 BLOWER ASSEMBLY 5835ED2002A 1K121 GASKET 4986DD3003A BLOWER GASKET 1K122 COVER, BLOWER 3550ED3011A 1K124 VENT 5232ED2001A 1K141 DOOR HINGE ASSEMBLY 4775DD2001A 1K142 DOOR HINGE ASSEMBLY 4775DD2002A 1


5020ED3008E 6


BBWB

WB

WB

WB

BBST

BBSTWBBBST

BBST

ST

- 60 -- 60 -

3790ED3007D 1K203 WINDOW 3790ED3007D TOP WINDOW 1

3790ED3007E 1K207 COVER, GUIDE 3550ED3012A 1

3720ED1005A 1K208 PANEL, CONTROL 3720ED1005B 1

3720ED1005C 15020ED3011A 1


K215 COVER, GUIDE 3550ED1009A 15020ED3012C 1

K216 BUTTON, CONTROL 5020ED3012D OPTION BUTTON 45020ED3012E 43846ER1001A 1

K220 MARK, PET 3846ER1001B 13846ER1001A 1

K251 PWB(PCB) ASSEMBLY, MAIN 6871DD1006A 1K252 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2001A 1K253 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2002A 1K260 LATCH, ASSEMBLY 4027ED3002A 1M001 HOLDER 4930DD3002A 1M005 GASKET 4986DD3002A SUMP GASKET 1M006 SUMP, ASSEMBLY 3485ED1002A 1M007 SUMP 3485DD1001A SUMP+SEAL+GREASE 1M025 VALVE, CHECK 5220DD3001A 1M026 MOTOR ASSEMBLY, WM 4681ED3001B VARIO MOTOR 1M027 SWITCH, MICRO 3W40025C 1M028 CAM, SWITCH 4430ED3001A 1M031 PACKING 3920ED4009B VARIO PACKING 1M034 BLADE 5832DD4001A 1M035 SEAL 4036DD3001A 1M036 HOLDER 4930DD3008A 1M037 FILTER ASSEMBLY, MESH 5231DD1001A 1M038 HOLDER 4930DD3012A 1M050 MOTOR ASSEMBLY, PUMP 4681EA2002D DRAIN MOTOR 1M060 MOTOR ASSEMBLY, WM 4681ED1004A 1M081 HEATER ASSEMBLY 5301DD1001A 1M086 MICRO S/W 3W40025P 1M087 SENSOR ASSEMBLY 6501ED2002D SOIL SENSOR 1M088 PROTECTOR (MECH) 3740ED3003A 1M090 FLOAT ASSEMBLY 4769DD2001A 1M110 FILTER ASSEMBLY, MESH 5231ED1001A 1M120 CASE ASSEMBLY 3111DD1001A 1M130 IMPELLER ASSEMBLY 5911ED3003A 1M210 VALVE ASSEMBLY, INLET 5221DD1001A 1M220 VALVE, CHECK 5220ED4004A 1M260 BASE, CABINET 3040ED1003A 1M261 COVER ASSEMBLY, BASE 3551DD1002A 1M262 CASE 3110DD3002A 1M270 LEG 4778ED3001A 1


BBST

BBWB

WB

WB

WB

WB

ST

BBST

BBST

BBST

- 61 -

*001 MANUAL ASSEMBLY, OWNERS 3829DD3005M 1*002 BOX, CARTON 3890DZ3015A 1*003 MANUAL, SERVICE 3828ED3001X 1*005 ACCESSORY ASSEMBLY 5001DD4001A 1A003 FELT 4766DD2004A LOWER FELT 1A005 BRACKET, TOP 4810DD4002B 4A006 SUPPORTER, HOLDER 4980ED2015A 1A007 SUPPORTER, HOLDER 4980ED2014A 1A008 SUPPORTER, HOLDER 4980ED2018A 1

3090ED1001A 1A010 CABINET 3090ED1001B 1

3090ED1001C 13090ED1002A 1



A050 NOZZLE ASSEMBLY 5249DD1002A LOWER NOZZLE 1A060 NOZZLE ASSEMBLY 5249DD1001A UPPER NOZZLE 1A070 GUIDE ASSEMBLY 4974DD9001A 1A073 WASHER, DRAWING 1WZZDD3001A 1A074 SHAFT, NOZZLE 4370ED3007A 1A080 RACK 3750DD2001A CUP RACK 2A101 DECO HANDLE 3806DD3004A STS 1A102 HANDLE FRONT 3650DD3001A FRONT 1A103 HANDLE REAR 3650DD3002A REAR 1A110 BASKET ASSEMBLY, SPOON 5005DD1001A 1A120 HARNESS, PWB 6877DD1002A 1A130 HOSE ASSEMBLY, DRAIN 5215ED3001E 1A140 RACK ASSEMBLY 3751DD1006A LOWER RACK 1A141 RACK 3750DD1007A 1A142 ROLLER ASSEMBLY 4581DD9002B 8A144 RACK 3750DD2003A 2A147 HOLDER 4930DD3006A 3A150 RACK ASSEMBLY 3751DD1005A UPPER RACK 1A151 RACK 3751DD1005A 1A152 ROLLER ASM 4581DD3002A 10A158 HOLDER 4930DD3005A 3A160 FILTER ASSEMBLY (CIRC) 6201EC1006A 1E010 BUSHING 4830ED4001A 2F001 FRAME ASSEMBLY 3211DD1001A 1F004 NOZZLE ASSEMBLY 5249DD2001A TOP NOZZLE 1F005 SHAFT NOZZLE 4370ED3006A TOP NOZZLE 1






BBSTWB

WB

BBSTWBBBST

- 62 -

F011 SPRING, HINGE 4970ED4004A 2F013 CONNECTOR ASSEMBLY 4933DD3001A 2F014 HINGE, BRACKET 4810ED4004A 2F022 SENSOR ASSEMBLY 6501DD2001A 1F040 GUIDE ASSEMBLY 4975DD1001A 1F041 HOSE, INLET 5214DD3001A 1F042 HOSE, CONNECTOR 5214DD3003A 1F043 HOSE, CONNECTOR 5214DD3002A 1F045 COVER, PROTECT 3550DD2001A 1F050 NUT, DRAWING 4020FD3641C 1F060 GASKET 4986DD3001A 1F101 PACKING 3920DD3002A 1F110 RAIL ASSEMBLY 5219DD2002A MUST CHANGE F117 TOGETHER(REF 24P-13) 1F013 CONNECTOR ASSEMBLY 4933DD3001A 2F117 STOPPER, ROLLER 4620ED3001A 2F132 PACKING 3920DD3005A TUB PACKING 1F143 HINGE ASSEMBLY 4775ED3004A 1F144 HINGE ASSEMBLY 4775ED3003A 1F171 LATCH, LOCK 4026DD3001A 1F174 BRACKET, HINGE 3751DD1006A DOOR FRAME 1F191 GUIDE, WATER 4974DD2003A 1F192 GUIDE, NOZZLE 4974DD3001A 1F210 RAIL ASSEMBLY 5219DD2001A MUST CHANGE F117 TOGETHER(REF 24P-13) 1K001 DISPENSER 4924FD2123E 1K002 BRACKET ASSEMBLY 4810FD3805A 2

3650ED2006A 1K005 HANDLE 3650ED2006B 1

3650ED2006C 13806ED3008A 2

K006 DECO, HANDLE 3806ED3008B 23806ED3008C 23550ED0001E 1

K010 COVER FRONT 3550ED0001F 13550ED0001G 13551DD1003H 1

K030 COVER ASSEMBLY, FRONT 3551DD1003F 13551DD1003G 1

K100 DOOR LINER ASM 4937DD9001A DOOR LINER + DAMPING SHEET + GASKET 1K110 BLOWER ASSEMBLY 5835ED2002A 1K121 GASKET 4986DD3003A BLOWER GASKET 1K122 COVER, BLOWER 3550ED3011A 1K124 VENT 5232ED2001A 1K141 DOOR HINGE ASSEMBLY 4775DD2001A 1K142 DOOR HINGE ASSEMBLY 4775DD2002A 1


5020ED3008R 53790ED3007Q 1K203 WINDOW 3790ED3007R TOP WINDOW 1


WB

STWBBBST

BB

WB

STWBBBST

WBBBSTWBBB

BB

- 63 -

K203 WINDOW 3790ED3007P 1K207 COVER, GUIDE 3550ED3012B 1

3720ED1005E 1K208 PANEL, CONTROL 3720ED1005F 1

3720ED1005D 15020ED3011A 1


K215 COVER, GUIDE 3550ED1009B 15020ED3012C 25020ED3012D 2K216 BUTTON, CONTROL5020ED3012E

OPTION BUTTON2

3846ER1001A 1K220 MARK, PET 3846ER1001B 1

3846ER1001A 1K251 PWB(PCB) ASSEMBLY, MAIN 6871DD1006A 1K252 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2001A 1K253 PWB(PCB) ASSEMBLY, DISPLAY 6871DD2002A 1K260 LATCH, ASSEMBLY 4027ED3002A 1M001 HOLDER 4930DD3002A 1M005 GASKET 4986DD3002A SUMP GASKET 1M006 SUMP, ASSEMBLY 3485ED1002B 1M007 SUMP 3485DD1001A SUMP+SEAL+GREASE 1M025 VALVE, CHECK 5220DD3001A 1M026 MOTOR ASSEMBLY, WM 4681ED3001B VARIO MOTOR 1M027 SWITCH, MICRO 3W40025C 1M028 CAM, SWITCH 4430ED3001A 1M031 PACKING 3920ED4009B VARIO PACKING 1M034 BLADE 5832DD4001A 1M035 SEAL 4036DD3001A 1M036 HOLDER 4930DD3008A 1M037 FILTER ASSEMBLY, MESH 5231DD1001A 1M038 HOLDER 4930DD3012A 1M050 MOTOR ASSEMBLY, PUMP 4681EA2002D DRAIN MOTOR 1M060 MOTOR ASSEMBLY, WM 4681ED1004A 1M081 HEATER ASSEMBLY 5301DD1001A 1M086 MICRO S/W 3W40025P 1M087 SENSOR ASSEMBLY 6501ED2002E SOIL SENSOR 1M088 PROTECTOR (MECH) 3740ED3003A 1M090 FLOAT ASSEMBLY 4769DD2001A 1M110 FILTER ASSEMBLY, MESH 5231ED1001A 1M120 CASE ASSEMBLY 3111DD1001A 1M130 IMPELLER ASSEMBLY 5911ED3003A 1M210 VALVE ASSEMBLY, INLET 5221DD1001A 1M220 VALVE, CHECK 5220ED4004A 1M260 BASE, CABINET 3040ED1003A 1M261 COVER ASSEMBLY, BASE 3551DD1002A 1M262 CASE 3110DD3002A 1M270 LEG 4778ED3001A 1


WBBBST

ST

WBBBST

WBBBSTWBBBST

- 64 -

MEMO

- 65 -

MEMO

P/No. : 3828ED3001X

#EV##EV##EV##EV##EV##EV##EV##EV##EV#

ldf6810 service manual

Documents