l -326 parts manual · 235 separator locking thumb screw 326.0.094 236 e -cl ip do6799.001 237...
TRANSCRIPT
L-326 PARTS MANUAL
Part # M-3075 Revision Date: 12/28/00
RENA Systems, Inc. 136 Green Tree Rd Ste 140
PO Box 1069 Oaks, PA 19456-1069
Telephone: 610/650-9170
Fax: 610/650-9171 E-Mail: [email protected]
Web Site: http://www.renausa.com
L326 Parts Manual 2.doc Rev 12-28-00 2
RENA Systems, Inc. 136 Green Tree Rd Ste 140 PO Box 1069 Oaks, PA 19456-1069
Telephone: 610/650-9170 Fax: 610/650-9171 E-Mail: [email protected] Web Site: http://www.renausa.com Every effort has been made to assure the accuracy of this manual. RENA Systems shall not be held liable for any errors contained herein or for any consequential or incidental damages incurred as a result of acting on information contained in this manual. Technical specifications may change due to design advances. The data stated are nominal values only.
L326 Parts Manual 2.doc Rev 12-28-00 3
Diagram Number
Description Part Number
101 Back Cover 326.1.021
102 Elevation Guide Assembly Complete 326.2.021
103 Cross Bar for Elevation Guide 292.0.027
104 Lower Front Cover 326.1.052
105 Model Number Decal K4711.013
106 Upper Front Cover 326.0.109
107 Screw DO7985.058
108 Label Advance Knob K4212.001
109 Label Advance Knob Cap K3610.025
110 220 Volt Power Cord K5602.001
111 110 Volt Power Cord K5602.002
112 Frame Assembly Complete 326.4.001
113 Rubber Foot 901.0.016
114 Material Receiving Tray 325.1.021
115 Receiving Tray Feet 325.0.074
116 Receiving Tray Paper Stop 404.0.139
117 Transport Pressure Decal K4718.055
118 Serial Number Plate 220 Volt Model 326.0.005
119 Serial Number Plate 110 Volt Model 326.0.006
120 Millimeter Ruler Decal K4718.054
121 Spacer 325.0.099
L326 Parts Manual 2.doc Rev 12-28-00 4
Diagram Number
Description Part Number
201 Frame Assembly (Bushing: K3711.004) 326.3.001
202 Upper Inside Support Bracket 326.0.060
203 Control Panel Assembly Complete 326.1.503
204 Large Metal Sleeve 326.0.086
205 Screw (M8X16) DO0912.046
206 Washer (8.4) DO0125.007
207 Upper Transport Assembly Complete 326.4.002
208 Round Support Bar 326.0.085
209 Flat Anchoring Bar Assembly 326.1.045
210 Flat Anchoring Bar 326.0.084
211 Grounding Spring 326.0.083
212 Screw (M3X6) DO7985.020
213 Washer (3.2) DO0125.002
214 Hinge Plate Assembly Complete 326.3.003
215 Hinge Plate Assembly 326.1.035
216 Hinge Plate 326.0.071
217 Transport Guide Rail 326.0.072
218 Transport Assembly Locking Thumb Screw 326.0.111
219 E-Clip DO6799.003
220 Screw (M4X20) DO7985.029
221 Washer (4.3) DO0125.003
222 Pin DO0007.038
223 Transport Assembly Height Adjusting Wheel 326.0.074
224 Nylon Washer (M4X8.1X1.5) K3103.623
225 Separator Assembly Complete 326.1.026
226 Separator Assembly Rear Plate 326.0.106
227 Separator Assembly Front Cover 305.0.003
228 Separator Tip 292.0.007
229 Separator Assembly E-Clip Plate 326.0.075
230 Separator Assembly Lift Bar 326.0.081
231 Separator Assembly Mounting Block 326.1.034
232 Input Copy Stop Plate 326.1.025
233 Washer (6) K3113.008
L326 Parts Manual 2.doc Rev 12-28-00 5
Diagram Number
Description Part Number
234 Hex Screw (M6X16) DO0912.035
235 Separator Locking Thumb Screw 326.0.094
236 E-Clip DO6799.001
237 Center Pressure Roller Cover 326.1.031
238 Flat Head Screw (M4X8 FHS) DO0965.051
239 Outer Bracket 326.0.067
240 Inner Bracket 326.0.068
241 Upper Exit Roller Cover Lock Knob 326.0.080
242 Screw (M3X10) DO7985.013
243 Upper Exit Roller Cover Lock Assembly 326.1.059
244 Upper Exit Roller Cover Lock Shaft 326.0.076
245 Upper Exit Roller Cover Lock Knob Mounting Post 326.0.077
246 Set Screw K6004.004
247 Nut DO0934.005
248 Upper Exit Roller Cover Lock Housing 326.0.065
249 Center Pressure Roller Assembly 326.2.013
250 Center Pressure Roller 902.1.001
251 Center Pressure Roller Spring Assembly 326.1.032
252 Screw DO7985.005
253 Center Pressure Roller Plate 326.1.049
254 Flat Head Screw (M5X20 FHS) DO0965.026
255 Upper Exit Roller Assembly Complete 326.2.024
256 Copy Pressure Plate 326.1.050
257 Upper Exit Roller Cover 326.1.030
258 Screw (M3X8) DO0965.041
259 Upper Exit Roller Cover Lock Block 326.0.066
260 Nut (M-4) DO0934.004
261 Upper Exit Roller Mounting Block 326.0.064
262 Set Screw (M5X6) DO0913.016
263 Upper Exit Roller Pressure Pin Assembly 326.1.028
264 Pressure Spring K2005.011
265 Pressure Pin 326.0.063
L326 Parts Manual 2.doc Rev 12-28-00 6
Diagram Number
Description Part Number
266 Upper Exit Roller 326.1.003
267 Spring Washer K2002.005
268 Control Panel Decal (German) K4718.049
269 Control Panel Decal (English) K4718.050
270 LED Display Cover 326.0.110
271 Double Wide Key w/LED EO808.044
272 Key w/LED EO808.082
273 Key w/o LED EO808.022
274 Potentiometer (Slide Control) Knob E2010.052
Not Pictured Potentiometer (Slide Control) EO606.056
L326 Parts Manual 2.doc Rev 12-28-00 7
Diagram Number
Description Part Number
301 Input Copy Platform 326.1.007
302 Inner Copy Side Guide 326.0.101
303a Small Outer Copy Side Guide 326.0.102
303b Medium Outer Copy Side Guide 326.0.100
303c Wide Outer Copy Side Guide 326.0.113
304 Thumb Screw for Copy Side Guide K2913.029
305 Support Shaft 326.0.047
306 Side Guide Anchor Block 326.0.097
307 Motor Cover 326.1.008
308 Flat Head Screw (M3-.5X6 FHS) M3-.5x6 FHS
309 Ribbed Washer (K3113.006) M4 RW
310 Label Drive Access Panel 326.1.005
311 Label Drive Pressure Roller Assembly Complete 326.2.025
312 Label Drive Pressure Roller Assembly 326.1.018
313 Label Drive Pressure Roller Spring K2009.011
314 Label Drive Pressure Roller Support 326.0.049
315 Yellow Roller Shaft 326.0.048
316 Yellow Roller 326.1.017
317 Yellow Roller Bushing 326.0.010
318 Flat Head Screw (M4X8 FHS) DO0965.012
319 Input Rubber Feed Roller 326.1.001
320 Input Feed Roller Outer Hub 326.0.029
321 Input Feed Roller Securing Bracket 326.1.019
322 Pan Head Screw (M4X5 PHS) DO7985.011
323 Lower Outside Support Plate 326.2.015
324 Copy Sensor Assembly Complete 326.2.009
325 Nose Guide Flap-Plate 326.1.051
326 Nose Guide Housing Shaft 326.0.118
327 Pan Head Screw (M2X6 CHMS) DO0084.003
328 Washer (2) K3113.002
329 Nose Guide Housing 326.0.116
330 Nose Guide 326.0.117
L326 Parts Manual 2.doc Rev 12-28-00 8
Diagram Number
Description Part Number
331 Label Pressure Adjustment Shaft 326.1.024
332 Internal Label Guide Plate 326.1.002
333 Label/Tab Guide Assembly Complete 326.2.023
334 Label Guide Shaft 326.0.095
335 Inner Label Guide Assembly Complete 326.1.036
336 Inner Label Guide 326.0.182
337 Label Guide Block 326.0.121
338 Label Sensor Assembly Complete 326.1.703
339 Outer Label Guide Assembly Complete 326.1.037
340 Screw K3205.003
341 Inner Tab Guide 326.1.039
342 Outer Tab Guide 326.1.038
343 Exit Roller Shield 326.1.023
344 Label Peel-Plate 326.0.040
345 Take-Up Spool (Pin for Spool: DO0007.014) 326.2.020
346 Stick-On Cable Tie Mount K5618.001
347 Cable Tie K5615.001
348 Copy Sensor 326.1.702
349 Spacer (14X5.1X1.5) K3103.624
350 Hex Nut (DO0934.003) M3-.5 HN
351 Center Table Top Plate 326.1.009
352 Tab Deflector Roller 326.1.043
353 Outer Input Feed Roller Mounting Assembly 326.2.007
354 Flat Washer (K3113.007) M4X9 FW
355 Copy Platform Support Bars 326.0.011
356 Pan Head Screw (DO7985.010) M5-.8X10 PHS
357 Hex Screw (M4X6) DO0912.011
358 Screw (M3X12) DO0084.034
359 Light Aperture Block 326.0.120
360 Label Sensor Block 326.0.119
361 Label Advance Bearing Assembly 325.1.024
362 Outer Label Guide 326.0.183
L326 Parts Manual 2.doc Rev 12-28-00 9
Diagram Number
Description Part Number
401 Lower Inside Support Bracket (Bushing: K3711.004) 326.2.005
402 Belt 90 XL 031 KO416.002
403 Belt KO416.003
404 Washer DO0125.009
405 Exit Roller Drive Belt KO416.004
406 Take-Up Spool O-Ring K4011.007
407 Take-Up Spool Slip Clutch Assembly 326.1.042
408 Keyed Washer DO0462.001
409 Large O-Ring Drive Spool 326.0.089
410 Slip Clutch Spring K2005.014
411 Washer (13) DO9021.009
412 Hex Nut DO0439.009
413 Take-Up Spool Drive Shaft 326.0.090
414 Take-Up Spool Bearing 326.0.087
415 Timing Sensor Assembly 326.2.006
416 Screw (M2.5X6) DO0084.027
417 Washer K3103.601
418 Timing Sensor 326.1.504
419 Timing Sensor Bracket 326.0.053
420 Timing Disk Assembly 326.1.010
421 Timing Disk 325.0.050
422 Timing Disk Mount 326.0.057
423 Set Screw (M4X6) DO0916.012
424 Motor Assembly Complete 326.2.002
425 Motor Drive Sprocket 326.0.014
426 Motor Collar 326.0.009
427 Motor 325.1.031
428 Power Transfer Assembly 326.1.020
429 Small O-Ring Drive Spool 326.0.088
430 Set Screw 326.0.088
431 Small Transfer Sprocket 326.0.015
432 Large Transfer Sprocket 326.0.019
L326 Parts Manual 2.doc Rev 12-28-00 10
Diagram Number
Description Part Number
433 Transfer Shaft 326.0.030
434 Feed Roller Drive Assembly 326.1.054
435 Feed Roller Drive Shaft 326.0.027
436 Feed Roller Inner Drive Hub 326.0.026
437 Feed Roller Hub Pin DO1474.002
438 Feed Roller Slip-Clutch Spring K2005.015
439 Hex Nut DO0439.007
440 Small Feed Roller Drive Sprocket 326.1.015
441 Large Feed Roller Drive Sprocket 326.1.022
442 Sleeve 326.0.025
443 Transport Roller Drive Assembly 326.1.055
444 Set Screw (M4X5) DO0916.003
445 Center Transport Roller Drive Sprocket (Short Collar) 326.0.016
445-B Center Transport Roller Drive Sprocket (Long Collar) 326.0.017
446 Transport Roller Drive Gear 326.0.012
447 Roll Pin DO7344.017
448 Transport Roller Shaft 326.0.042
449 Transport Roller 325.0.012
450 Clutch 326.1.705
451 Clutch Spacer 312.0.232
452 Clutch/Brake Disk 431.1.112
453 Carrier 291.0.105
454 Clutch Shaft Key DO6888.001
455 Label Advance Roller 326.1.058
456 Screw (M4X12) DO7985.026
457 Label Sensor Wire Protector 326.0.096
458 Brake 326.1.706
459 Exit Roller Sprocket 326.0.013
460 Collar 326.0.008
461 Exit Roller (Bushing operator side: K3711.002) 326.1.006
462 Motor Brush KO125.002
463 Screw (M5X10) DO0912.024
L326 Parts Manual 2.doc Rev 12-28-00 11
Diagram Number
Description Part Number
464 Transport Shaft Bushings (Pressed into #401 & #201) K3711.004
465 Roller Bearing (608Z) K3812.010
466 Bearing Sleeve 291.0.096
Cheese Head Machine Screw M2-X5 CHMS
Washer M2X5
467 Exit Roller Bushing (Pressed into #323) K3711.002
Diagram Number
Description Part Number
501 Main P.C. Board 326.1.501
Si1 1 Amp 250 Volt Fuse (Slow Blow) E2008.045
Si2 1 Amp 250 Volt Fuse (Slow Blow) E2008.045
Si3 630mA (0.63 A) 250 Volt Fuse (Slow Blow) E2008.043
502 Display Ribbon Cable 326.1.704
503 Ground Cable 325.1.704
504 1 Amp 250 Volt Fuse (Slow Blow) (For 220 V System) E2008.045
505 2 Amp 250 Volt Fuse (Slow Blow) (For 110 V System) E2008.048
506 Power Receptacle Assembly 326.1.711
507 Hex Nut (M6) DO0934.006
508 Washer (6.4) DO09021.006
509 Transformer 326.1.708
510 Label Sensor Cable Tension Spring 326.0.105
511 Label Sensor Cable Tension Arm 326.0.153
512 Ground Decal K4714.001
513 Board Mount K3607.002
514 Washer DO6798.019
Not Pictured Transport Shaft Bushings (Pressed into pos. # 201 & 401.) K3711.004
L326 Parts Manual 2.doc Rev 12-28-00 12
L-326 BELT DIAGRAM (NOT DRAWN TO SCALE)
L326 Parts Manual 2.doc Rev. 7-10-00 13
121
L326 Parts Manual 2.doc Rev. 7-10-00 14
L326 Parts Manual 2.doc Rev. 7-10-00 15
L326 Parts Manual 2.doc Rev. 7-10-00 16
445-B
466
465
464
464
464
467
L326 Parts Manual 2.doc Rev. 7-10-00 17