kontax stirling engines kg09 instructions
TRANSCRIPT
![Page 1: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/1.jpg)
Kontax Stirling Engines KG09 instructions
This document covers the following:
Tools required
Parts list
Assembly instructions
Operating instructions
Maintenance
Contact details:
www.stirlingengine.co.uk
Tel: 01452 905001 (UK)
![Page 2: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/2.jpg)
Tools you will need to assemble your
KG09 Stirling Engine:
Cross-point screwdriver,
elastic band,
ruler.
![Page 3: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/3.jpg)
Base plate x1
Cradle x1
Burner cap x1
Bottom pillar x1
Burner body x1 Flywheel x2 Joint ring x1 Fin block x1
![Page 4: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/4.jpg)
Displacer stem x1 Displacer x1 Glass dome x1
Crank & conrod
assembly x1
Piston x1 Cylinder x1
Tube x1 Displacer clevis x1 Wick x1
Cylinder
Port x1
![Page 5: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/5.jpg)
13mm O ring x1
M2x6mm
roundhead x2 M3x8mm
countersunk x4
4mm Ball-race
bearing x2
M3x6mm
countersunk x4
17mm O ring x2
M2x5mm
countersunk x2
Conrod bush x2
Feet x4 (1 strip)
7mm O ring x2 3mm O ring x4
![Page 6: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/6.jpg)
Fit the first 17mm O ring into the
first groove in the hole in the end
of the fin block.
Note, the fin block is cut away for
clarity.
![Page 7: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/7.jpg)
Fit the second 17mm O ring into
the second groove in the hole in
the end of the fin block.
Note, the fin block and first O ring
are shown cut away for clarity.
![Page 8: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/8.jpg)
Align the hole in the fin block as
shown in the diagram and push
the block into the hole in the
packing tray.
![Page 9: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/9.jpg)
Lower the joint ring onto the
step on the end of the fin
block.
![Page 10: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/10.jpg)
Align the cradle as shown in the diagram and lower onto
the joint ring.
Fit four M3x6mm countersunk screws through
the four holes in the cradle and into the
four holes in the end of the fin
block.
Screw each screw nearly
all the way in.
![Page 11: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/11.jpg)
Fully tighten all four screws.
Note, the cradle is shown cut
away for clarity.
![Page 12: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/12.jpg)
Remove from the hole in the packing tray and align
the holes in the fin block and cradle downwards as
shown in the diagram. Push the
block and cradle into the long
hole in the packing tray.
![Page 13: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/13.jpg)
Fit two M3x8mm countersunk
screws through the holes in the
bottom pillar and into the holes in
the cradle.
Screw each screw nearly
all the way in.
![Page 14: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/14.jpg)
Fully tighten the screws. Note, the bottom pillar is shown cut away for clarity.
![Page 15: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/15.jpg)
Locate the underside of the base plate. The underside is the side with the
countersinks on the two holes as shown in the diagram.
![Page 16: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/16.jpg)
With the underside facing upwards, lower the base plate onto the bottom pillar.
Align the two holes in the plate with the two
holes in the pillar and start
inserting two M3x8mm
countersunk screws.
Screw each screw nearly
all the way in.
![Page 17: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/17.jpg)
Fully tighten the screws.
![Page 18: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/18.jpg)
Peel the backing off the four rubber feet and stick
them to the underside of the base plate.
Position them as shown in the diagram.
![Page 19: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/19.jpg)
Remove from the packing tray.
![Page 20: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/20.jpg)
Lay the crank and conrod out as shown.
Fit one M2x6mm roundhead screw through the front conrod, screw it all the way through
a conrod bush, and screw it into the piston a couple of turns. The conrod bush should fit
fully into the conrod.
![Page 21: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/21.jpg)
Fully tighten the screw.
![Page 22: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/22.jpg)
Fit one M2x6mm roundhead screw through the back conrod, screw
it through the conrod bush and into the displacer clevis a couple of
turns.
The conrod bush should fit
fully into the conrod.
![Page 23: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/23.jpg)
Fully tighten the screw.
![Page 24: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/24.jpg)
Screw the shorter end of the displacer stem into the displacer clevis.
You can screw either end in, the stem is the same on both ends.
![Page 25: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/25.jpg)
Fully tighten. You might need to
wrap an elastic band around to
stem for grip.
![Page 26: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/26.jpg)
Screw two M2x5mm
countersunk screws a
couple of turns each into
the holes in the two cranks.
![Page 27: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/27.jpg)
Screw the screws in until the tops are
about 1mm from the tops of the
cranks.
![Page 28: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/28.jpg)
Align the cranks and conrods as shown in the diagram and
slide the displacer stem all the way into the hole in the
middle of the fin block, it should slide freely.
Note, the cradle is shown cut away for clarity.
![Page 29: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/29.jpg)
1. Push the displacer stem all the way in.
2. Position the cranks on the bottom of the cradle.
3. Angle the piston as shown in the diagram and push it
up through the hole on the top of the cradle.
1
2
3
![Page 30: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/30.jpg)
Push the piston right up through the front hole.
Flip the piston over and position it over the
edge of the rear hole in the cradle.
The black part of the piston should catch on
the edge of the rear hole
and should prevent
the whole piston
and conrod falling
back through the
front hole.
![Page 31: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/31.jpg)
If the piston won’t stay hooked over
the hole you can stretch an elastic
band around it to hold it in place.
![Page 32: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/32.jpg)
Fit two 4mm ball-race bearings
into the holes
in the cradle.
The bearings
have a dust
shield on one side
and are open on the
other. The open side
should face inwards
after fitting.
Note, the cradle is
shown cut away for clarity.
![Page 33: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/33.jpg)
Fit the first flywheel through the 4mm
bearing and into the hole in the crank.
The end of the flywheel should line up
flush with the inside face of the crank.
Note, the cradle is shown cut away for
clarity.
![Page 34: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/34.jpg)
Fit the second
flywheel through
the 4mm bearing
and into the hole in the
crank. The end of the flywheel should
line up flush with the inside face of
the crank.
Note, the cradle is shown cut away for
clarity.
![Page 35: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/35.jpg)
The flywheel rims have a slot in them for balancing. Align the middle of the balancing slot
directly opposite the middle of the crank as shown by arrows 1 & 2 in the diagram. Make
sure the flywheel axle is flush with the inside of the crank and then fully tighten the crank
screw.
Note, the cradle is shown cut away for clarity.
1
2
![Page 36: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/36.jpg)
Align the middle of the balancing slot on the other flywheel directly opposite the middle of
the crank as shown by arrows 1 & 2 in the diagram. Make sure the flywheel axle is flush
with the inside of the crank and then fully tighten the crank screw. Note, the cradle is
shown cut away for clarity.
1
2
2
![Page 37: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/37.jpg)
Hold the piston vertically and lower
the cylinder down over it.
Lower the cylinder all the way down
to the hole in the cradle.
![Page 38: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/38.jpg)
Screw the cylinder into the hole in the
cradle and fully tighten, you might need to
wrap an elastic band around it for grip.
![Page 39: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/39.jpg)
Fit two 3mm O rings into the two
grooves in one the end of the tube.
![Page 40: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/40.jpg)
Fit two 3mm O rings into the two
grooves in the other end of the tube.
![Page 41: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/41.jpg)
Fit two 7mm O rings into the two
grooves in the end of the cylinder
port.
![Page 42: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/42.jpg)
The brass fittings on the end of the tube are different sizes.
Moisten the O rings on the smaller of the two fittings sparingly with slightly soapy
tap water for lubrication and fit into the hole in the cylinder port.
A gentle pushing and twisting motion works best. Do not allow
the O rings to bunch up or get pinched in the hole in the port.
Push in until the O rings are just inside the hole.
![Page 43: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/43.jpg)
The tube and cylinder port need adjusting to the correct length.
1. Position the tube over the engine so that the left end is in line with the hole in
the fin block.
2. Adjust the position of the tube in the cylinder port so that the middle of the port
is in line with the middle of the glass cylinder (3).
1
2
3
![Page 44: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/44.jpg)
Moisten the two O rings on the tube and the two on the cylinder port sparingly with
slightly soapy tap water for lubrication. Lower the
tube and port into the fin block and cylinder.
![Page 45: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/45.jpg)
Apply even, gentle pressure on the tube fitting and cylinder
port. Push both down until the bottom of the port is flush
with the top of the glass cylinder.
You MUST push both in at the same time. If you try to
push one in all the way and then the other you could
break the glass cylinder.
![Page 46: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/46.jpg)
1
Rotate the flywheels until the piston is at the
top of its stroke. Check that the top of the
piston does not touch the bottom of the
cylinder port (arrow 1).
If it touches, you will need to twist the glass
cylinder out of the glass holder (shown in blue
in the diagram) a small amount.
![Page 47: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/47.jpg)
Rotate the flywheel until the end of the displacer stem is as close to the end of the fin
block as it can get.
Note, the fin block is shown cut away for clarity.
![Page 48: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/48.jpg)
Screw the displacer onto the displacer stem.
Note, the fin block is shown cut away for clarity.
![Page 49: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/49.jpg)
Fully tighten.
Note, the fin block is shown cut away for
clarity.
![Page 50: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/50.jpg)
Moisten the end of the glass dome
sparingly with slightly soapy tap water for
lubrication and fit it into the hole in the
fin block. A gentle pushing and twisting
motion works best. Try not to allow the
glass to come into contact
with the sides of the hole.
![Page 51: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/51.jpg)
The end of the dome should be 21mm
from the end of the fin block.
![Page 52: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/52.jpg)
If the top end of the wick is frayed you will need to burn off the loose fibres, allow to
cool, and then roll the end into a blunt point.
ONLY EVER PERFORM THIS STEP ON DRY
WICK, NEVER ON WICK THAT HAS BEEN
SOAKED IN FUEL.
Insert the prepared end of the wick into
the burner cap, a pushing and twisting
motion works best.
![Page 53: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/53.jpg)
Trim the top of the wick to 5mm long.
![Page 54: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/54.jpg)
Trim the bottom of the wick to 15mm long.
![Page 55: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/55.jpg)
Fit one 13mm O ring into the groove in the bottom of the
burner body.
![Page 56: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/56.jpg)
Fit the burner cap into the
burner body.
![Page 57: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/57.jpg)
Fit the assembled burner into the
hole in the plate. It should slide
in quite easily.
The O ring will hold the burner
securely in position during
operation.
![Page 58: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/58.jpg)
Your engine is now fully assembled.
Check that the flywheels rotate fully, a small amount of
resistance will be felt due to the air pressure inside the
engine. Check that the displacer does not bump into
the end of the glass dome.
Once you have made these checks you
are ready to operate your engine.
![Page 59: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/59.jpg)
The engine uses Methylated Spirits or
Denatured Alcohol as fuel.
Remove the burner from the engine base
plate and remove the cap from the body.
There is a small step about a quarter of the
way down inside, fill with fuel to this level
AND NO MORE. Trim the wick to 5mm
protruding from the top and 15mm from the
bottom. Fit the cap back in the body.
The cap has a small vent slot on its
underside. This must always be kept clear or
the burner cap might pop off during
operation and spill burning fuel on the base
plate.
Fill level
![Page 60: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/60.jpg)
Light the wick and allow a minute or so for the engine to
warm up, then spin the flywheels in the direction shown in
the diagram.
The engine should run for about 10-15 minutes
before the fuel runs out.
Make sure you have a suitable
fire extinguisher to hand in
case of emergencies. Never
leave a running engine
or naked flame
unattended.
![Page 61: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/61.jpg)
Oiling your engine – put one drop of sewing machine or 3-in-1 oil on the displacer stem
(shown in blue) before the first run and one drop every two hours of run time thereafter.
![Page 62: Kontax Stirling Engines KG09 instructions](https://reader030.vdocuments.mx/reader030/viewer/2022021008/6203a53cda24ad121e4bd039/html5/thumbnails/62.jpg)
Oiling your engine – put one drop of sewing
machine or 3-in-1 oil on the four ball-race bearings
(shown in blue) before the first run and one drop
every two hours of run time thereafter.