koe tx20d200vm2bab tft-display distributed by data modul … · supply voltage vdd-0.5 5.0 v -...

TX20D200VM2BAB

8.” TFT - WVGA - LVDS

Version: TX20D200VM2BAB-1Date: 07.08.2014

Note: This specification is subject to change without prior notice

SPECIFICATION

w w w . d a t a - m o d u l . c o m

FOR MESSRS : DATE : Aug. 7th, 2014

CUSTOMER’S ACCEPTANCE SPECIFICATIONS

TX20D200VM2BAB

Contents

No. ITEM SHEET No. PAGE

1 COVER 7B64PS 2701-TX20D200VM2BAB-1 1-1/1

2 RECORD OF REVISION 7B64PS 2702-TX20D200VM2BAB-1 2-1/1

3 GENERAL DATA 7B64PS 2703-TX20D200VM2BAB-1 3-1/1

4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704-TX20D200VM2BAB-1 4-1/1

5 ELECTRICAL CHARACTERISTICS 7B64PS 2705-TX20D200VM2BAB-1 5-1/2~2/2

6 OPTICAL CHARACTERISTICS 7B64PS 2706-TX20D200VM2BAB-1 6-1/2~2/2

7 BLOCK DIAGRAM 7B64PS 2707-TX20D200VM2BAB-1 7-1/1

8 RELIABILITY TESTS 7B64PS 2708-TX20D200VM2BAB-1 8-1/1

9 LCD INTERFACE 7B64PS 2709-TX20D200VM2BAB-1 9-1/7~7/7

10 OUTLINE DIMENSIONS 7B64PS 2710-TX20D200VM2BAB-1 10-1/2~2/2

11 APPEARANCE STANDARD 7B64PS 2711-TX20D200VM2BAB-1 11-1/3~3/3

12 PRECAUTIONS 7B64PS 2712-TX20D200VM2BAB-1 12-1/2~2/2

13 DESIGNATION OF LOT MARK 7B64PS 2713-TX20D200VM2BAB-1 13-1/1

ACCEPTED BY: PROPOSED BY:

KAOHSIUNG OPTO-ELECTRONICS INC. SHEETNO. 7B64PS 2701-TX20D200VM2BAB-1 PAGE 1-1/1

2. RECORD OF REVISION

DATE SHEET No. SUMMARY


3. GENERAL DATA

3.1 DISPLAY FEATURES

This module is a 8.0” WVGA of 16:9 format amorphous silicon TFT. The pixel format is vertical stripe and sub pixels are arranged as R(red), G(green), B(blue) sequentially. This display is RoHS compliant, and COG (chip on glass) technology and LED backlight are applied on this display.

Part Name TX20D200VM2BAB

Module Dimensions 189.0(W) mm x 122.0(H) mm x 10.2 (D) mm

LCD Active Area 174.0(W) mm x104.4(H) mm

Pixel Pitch 0.2175(W) mm x 0.2175 (H) mm

Resolution 800 x 3(RGB)(W) x 480(H) Dots

Color Pixel Arrangement R, G, B Vertical Stripe

LCD Type Transmissive Color TFT; Normally White

Display Type Active Matrix

Number of Colors 262k Colors (6-bit RGB)

Backlight Light Emitting Diode (LED)

Weight 220 g

Interface LVDS; 20 pins

Power Supply Voltage 3.3V for LCD; 12.0V for backlight.

Power Consumption 0.89W for LCD; 4.92W for backlight.

Viewing Direction 12 O’clock (without image inversion and least brightness change)

6 O’clock (contrast peak located at)


4. ABSOLUTE MAXIMUM RATINGS

Item Symbol Min. Max. Unit Remarks

Supply Voltage VDD -0.5 5.0 V -

Input Voltage of Logic VI -0.5 5.0 V Note 1

Operating Temperature Top -30 80 C Note 2

Storage Temperature Tst -30 80 C Note 2

Backlight Input Voltage VLED - 15 V -

Note 1: The rating is defined for the signal voltages of the interface such as CLK and pixel data pairs.

Note 2: The maximum rating is defined as above based on the chamber temperature, which might be different from ambient temperature after assembling the panel into the application. Moreover, some temperature-related phenomenon as below needed to be noticed:

- Background color, contrast and response time would be different in temperatures other than 25 C .

- Operating under high temperature will shorten LED lifetime.


5. ELECTRICAL CHARACTERISTICS

5.1 LCD CHARACTERISTICS

Item Symbol Condition Min. Typ. Max. Unit Remarks

Power Supply Voltage VDD - 3.0 3.3 3.6 V -

Differential Input Voltage for LVDS

Receiver Threshold VI

VIH - - +100 mV Note 1

VIL -100 - -

Power Supply Current IDD VDD-VSS =3.3V - 270 377 mA Note 2,3

Frame Frequency Framef - - 60 66 Hz -

CLK Frequency CLKf - 25 33.3 40 MHz

Note 1: VCM 1.2V is common mode voltage of LVDS transmitter and receiver. The input terminal of LVDS receiver is terminated with 100Ω.

Note 2: An all black check pattern is used when measuring IDD. Framef is set to 60Hz.

Note 3: 0.63A fuse is applied in the module for IDD. For display activation and protection purpose, power supply is recommended larger than 1.6A to start the display and break fuse once any short circuit occurred.


IN+

IN- 100Ω

LVDS

Receiver

0VV 25 SS ,CTa

5.2 BACKLIGHT CHARACTERISTICS


LED Input Voltage VLED - 11.0 12.0 13.0 V Note1

LED Forward Current ILED 0V; 0% duty 360 410 460

mA Note 2 3.3VDC; 100% duty 30 40 50

LED lifetime - ILED=410 mA - 70K - hrs Note 3

Note 1: As Fig. 5.1 shown, LED current is constant, 410 mA, controlled by the LED driver when applying 12V VLED.

Note 2: Dimming function can be obtained by applying DC voltage or PWM signal from the display interface CN1. The recommended PWM signal is 1K ~ 10K Hz with 3.3V amplitude.

Note 3: The estimated lifetime is specified as the time to reduce 50% brightness by applying 410 mA at 25 C .

Fig 5.1

CTa25


6. OPTICAL CHARACTERISTICS The optical characteristics are measured based on the conditions as below:

- Supplying the signals and voltages defined in the section of electrical characteristics.

- The backlight unit needs to be turned on for 30 minutes.

- The ambient temperature is 25 C .

- In the dark room less than 100 lx, the equipment has been set for the measurements as shown in Fig 6.1.


Brightness of White - ILED= 410mA

0 ,0

1200 1500 - 2cd/m Note 1

Brightness Uniformity - 70 - - % Note 2

Contrast Ratio CR 400 800 - - Note 3

Response Time Tr + Tf 0 ,0 - 20 - ms Note 4

NTSC Ratio - 0 ,0 - 60 - % -

Viewing Angle

x 10 CR ,0 60 80 -

Degree Note 5 x 10 CR ,180 60 80 -

y 10 CR ,90 40 80 -

y 10 CR ,270 60 60 -

Color

Chromaticity

Red X

0 ,0

0.59 0.64 0.69

- Note 6

Y 0.29 0.34 0.39

Green X 0.31 0.36 0.41

Y 0.53 0.58 0.63

Blue X 0.09 0.14 0.19

Y 0.05 0.10 0.15

White X 0.26 0.31 0.36

Y 0.29 0.34 0.39

Note 1: The brightness is measured from 9 point average value of the panel, P5 in Fig. 6.2, for the typical value.

Note 2: The brightness uniformity is calculated by the equation as below:

which is based on the brightness values of the 9 points in active area measured by BM-5 as shown in Fig. 6.2.


Brightness uniformity = X100% Min. Brightness

Max. Brightness

3.3VV Hz, 60 25 DD Framea fCT ,

Fig 6.1 Fig 6.2

Distance: 500 mm

LCD panel

Field: 1

Photo Detector: BM-5

X62

X

X61

Y61

Y62

Y62

Y61

Y

X62 X

61

Note 3: The Contrast ratio is measured from the center point of the panel, P5, and defined as the following equation:

Note 4: The definition of response time is shown in Fig. 6.3. The rising time is the period from 90% brightness to 10% brightness when the data is from white to black. Oppositely, falling time is the period from 10% brightness rising to 90% brightness.

Note 5: The definition of viewing angle is shown in Fig. 6.4. Angle is used to represent viewing directions, for instance, 270 means 6 o’clock, and 0 means 3 o’clock. Moreover, angle is used to represent viewing angles from axis Z toward plane XY.

The display is super wide viewing angle version, so that the best optical performance can be obtained from every viewing direction.

,0)y (x,

0

90

180

270

Note 6: The color chromaticity is measured from the center point of the panel, P5, as shown in Fig. 6.2.


CR = Brightness of White

Brightness of Black

Fig 6.3

Fig 6.4

7. BLOCK DIAGRAM

Gate D

river

CN

1C

N2

Note : Signals are CLK and pixel data pairs.


8. RELIABILITY TESTS

Test Item Condition

High Temperature 1) Operating

2) 80 C 240 hrs

Low Temperature 1) Operating

2) -30 C 240 hrs

High Temperature 1) Storage

2) 80 C 240 hrs

Low Temperature 1) Storage

2) -30 C 240 hrs

Heat Cycle 1) Operating

2) –20 C ~70 C

3) 3hrs~1hr~3hrs 240 hrs

Thermal Shock 1) Non-Operating

2) -35 C 85 C

3) 0.5 hr 0.5 hr 240 hrs

High Temperature & Humidity

1) Operating

2) 40 C & 85%RH

3) Without condensation

240 hrs

(Note 3)

Vibration

1) Non-Operating

2) 20～200 Hz

3) 2G

4) X, Y, and Z directions

1 hr for each direction

Mechanical Shock

1) Non-Operating

2) 10 ms

3) 50G

4) Y X, and Z directions

Once for each direction

ESD

1) Operating

2) Tip: 150 pF, 330

3) Air discharge for glass: 8KV

4) Contact discharge for metal frame: 8KV

1) Glass: 9 points 2) Metal frame: 8 points

(Note 4)

Note 1: Display functionalities are inspected under the conditions defined in the specification after the reliability tests.

Note 2: The display is not guaranteed for use in corrosive gas environments.

Note 3: Under the condition of high temperature & humidity, if the temperature is higher than 40, the humidity needs to be reduced as Fig. 8.1 shown.

C)(

Note 4: All pins of LCD interface (CN1) have been tested by 100V contact discharge of ESD under non-operating condition.


9. LCD INTERFACE

9.1 INTERFACE PIN CONNECTIONS

The display interface connector CN1 is FI-SEB20P-HF13E made by JAE and pin assignment is as below:

Pin No. Signal Signal Pin No. Signal Signal

1 VDD Power Supply for Logic

11 IN2- B2~B5, DE

2 VDD 12 IN2+

3 VSS GND

13 VSS GND

4 VSS 14 CLK IN-Pixel Clock

5 IN0- R0~R5, G0

15 CLK IN+

6 IN0+ 16 VSS GND

7 VSS GND 17 NC No Connection

8 IN1- G1~G5, B0~B1

18 NC No Connection

9 IN1+ 19 NC No Connection

10 VSS GND 20 DIM Note 2

Note 1: IN n- and IN n+ (n=0, 1, 2), CLK IN- and CLK IN+ should be wired by twist-pairs or side-by-side FPC patterns, respectively.

Note 2: Normal brightness: 0V or 0% PWM duty; Brightness control: 0V to 3.3V DC or 0% to 100% PWM duty.

The backlight interface connector CN2 is SM02(8.0)B-BHS-1-TB made by JST, and pin assignment is as below:

Pin No. Signal Level Function

1 VLED+ - Power Supply for LED

2 VLED- - GND


9.2 LVDS INTERFACE

R0-R5,G0

G1-G5,B0,B1

B2-B5,NA,NA,DE

Controll THC63LVDM83R7 TA0-6

7 TB0-6

7 TC0-6

CKDCLK IN

PLL

2)Machine Side

THC63LVDF84B

PLL

3)1)

RA0-6

RB0-6

RC0-6LCD Panelcontroller

RD0-6

TFT-LCD SideCN1

(interface)

IN0+IN0-IN1+IN1-

IN2+IN2-

CLK IN+CLK IN-

DCLK OUT

Note 1: LVDS cable impedance should be 100 ohms per signal line when each 2-lines (+, -) is used in differential mode.

Note 2: The recommended transmitter, THC63LVDM83R, is made by Thine or equivalent, which is not contained in the module.

Note 3: The receiver built-in the module is THC63LVDF84B .

9.3 LVDS DATA FORMAT

DE: Display Enable

NA: Not Available

R1 R0 G0 R5 R4 R3 R2 R1 R0 G0

G2 G1 B1 B0 G5 G4 G3 G2 G1 B1

B3 B2 DE NA NA B5 B4 B3 B2 DE

1 cycle

CLK IN+

CLK IN-

IN0+

IN0-

IN1+

IN1-

IN2+

IN2-


9.4 TIMING CHART

Fig. 9.1 Horizontal Timing

Fig.9.2 Vertical Timing

CLK

70%

30%

Tdsu Tdhd

Tcph

1st RGB 2nd RGB

1st 2nd70%

30%

Tcwh

Tcwl

Last Data

30%

70%70%

Tesu Tehd

800 RGBData

DE

Fig. 9.3 Setup & Hold Time


9.5 TIMING TABLE

The column of timing sets including minimum, typical, and maximum as below are based on the best optical performance, frame frequency (Vsync) = 60 Hz to define. If 60 Hz is not the aim to set, less than 66 Hz for Vsync is recommended to apply for better performance by other parameter combination as the definitions in section 5.1.

A. Horizontal and Vertical Timing

Item Symbol Min. Typ. Max. Unit

Horizontal

CLK Frequency fclk 25 33.3 40 M Hz

Display Data thd 800 CLK

Cycle Time th 841 1056 1088

Vertical Display Data tvd 480

H Cycle Time tv 495 525 610

B. Setup and Hold Time


CLK Duty Tcwh 40 50 60 %

Cycle Time Tcph - 30 -

ns Data

Setup Time Tdsu 5 - -

Hold Time Tdhd 5 - -

DE Setup Time Tesu 5 - -

Hold Time Tehd 5 - -


9.6 LVDS RECEIVER TIMING


CLK Cycle frequency 1/tcLK 25 33.3 40 MHz

RinX

(X=0,1,2)

0 data position tRP0 1/7* tCLK -0.49 1/7* tCLK 1/7* tCLK +0.49

ns

1st data position tRP1 -0.49 0 +0.49

2nd data position tRP2 6/7* tCLK -0.49 6/7* tCLK 6/7* tCLK +0.49

3rd data position tRP3 5/7* tCLK -0.49 5/7* tCLK 5/7* tCLK +0.49

4th data position tRP4 4/7* tCLK -0.49 4/7* tCLK 4/7* tCLK +0.49



Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 Vdiff=0V

Vdiff=0VVdiff=0V

tCLK

CLK+

RinX= (RinX+)-(RinX-) (X=0, 1, 2)

RinX

tRP1

tRP0

tRP6

tRP5

tRP4

tRP3

tRP2


9.7 DATA INPUT for DISPLAY COLOR

Input color

Red Data Green Data Blue Data

R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

MSB LSB MSB LSB MSB LSB

Basic Color

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Blue(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Red

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red (1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0

Red (2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0

: : : : : : : : : : : : : : : : : : :

: : : : : : : : : : : : : : : : : : :

Red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0

Red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Green (1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0

Green (2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0

: : : : : : : : : : : : : : : : : : :

: : : : : : : : : : : : : : : : : : :

Green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0

Green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Blue

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Blue (1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

Blue (2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0

: : : : : : : : : : : : : : : : : : :

: : : : : : : : : : : : : : : : : : :

Blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0

Blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1


9.8 POWER SEQUENCE

Note 1: In order to avoid any damages, VDD has to be applied before all other signals. The opposite is true for power off where VDD has to be remained on until all other signals have been switch off. The recommended time period is 1 second. Hot plugging might cause display damage due to incorrect power sequence, please pay attention on interface connecting before power on.

Note 2: In order to avoid showing uncompleted patterns in transient state. It is recommended that switching the backlight on is delayed for 1 second after the signals have been applied. The opposite is true for power off where the backlight has to be switched off 1 second before the signals are removed.


11. APPEARANCE STANDARD The appearance inspection is performed in a room around 500~1000 lx based on the conditions as below:

- The distance between inspector’s eyes and display is 30 cm.

- The viewing zone is defined with angle shown in Fig. 11.1 The inspection should be performed within 45∘when display is shut down. The inspection should be performed within 5∘when display is power on.

11.1 THE DEFINITION OF LCD ZONE

LCD panel is divided into 2 areas as shown in Fig.11.2 for appearance specification in next section. A zone is the LCD active area (dot area); B zone is the area between A zone and metal frame.

In terms of housing design, B zone is the recommended window area customers’ housing should be located in.


Fig. 11.1

Fig. 11.2

11.2 LCD APPEARANCE SPECIFICATION

The specification as below is defined as the amount of unexpected phenomenon or material in different zones of LCD panel. The definitions of length, width and average diameter using in the table are shown in Fig. 11.4 and Fig. 11.5.

Item Criteria Applied zone

Scratches

Length (mm) Width (mm) Maximum number Minimum space

A L≦15 W≦0.02 Ignored -

L≦15 0.02＜W≦0.1 5 -

L＞15 0.1＜W 0 -

Dent Serious one is not allowed A

Wrinkles in polarizer Serious one is not allowed A

Bubbles on polarizer

Average diameter (mm) Maximum number

A D≦0.3 Ignored

0.3＜D≦0.6 4

0.6＜D 0

1) Stains 2) Foreign Materials

3) Dark Spot

Filamentous (Line shape)

A Length (mm) Width (mm) Maximum number

L≦2.0 W≦1.5 5

L＞2.0 1.5＜W 0

Round (Dot shape)

A

Average diameter (mm) Maximum number Minimum Space

D≦0.2 Ignored -

0.2＜D≦0.6 4 -

0.6＜D 0 -

Those wiped out easily are acceptable

Dot-Defect

(Note 1,2)

Area① Area② Maximum number

A Bright dot-defect 1 dot 2 dot 3 dot

Dark dot-defect 2 dot 3 dot 4 dot

Bright + Dark point 3 dot 4 dot 5 dot

Note 1: The Dot-Defect inspection within A zone (active area) would be divided into area ①, ② as Fig. 11.3 shown.


②

①

Fig. 11.3

Note 2: The definitions of dot defect are as below:

- The defect area of the dot must be bigger than half of a dot.

- For bright dot-defect, showing black pattern, the dot’s brightness must be over 30% brighter than others.

- For dark dot-defect, showing white pattern, the dot’s brightness must be under 70% darker than others.


Fig 11.4

Wid

th Length

Fig 11.5

a

b

Average diameter D = a+b

2

12. PRECAUTIONS

12.1 PRECAUTIONS of ESD

1) Before handling the display, please ensure your body has been connected to ground to avoid any damages by ESD. Also, do not touch display’s interface directly when assembling.

2) Please remove the protection film very slowly before turning on the display to avoid generating ESD.

12.2 PRECAUTIONS of HANDLING

1) In order to keep the appearance of display in good condition; please do not rub any surfaces of the displays by sharp tools harder than 3H, especially touch panel, metal frame and polarizer.

2) Please do not pile the displays in order to avoid any scars leaving on the display. In order to avoid any injuries, please pay more attention for the edges of glasses and metal frame, and wear finger cots to protect yourself and the display before working on it.

3) Touching the display area or the terminal pins with bare hand is prohibited. This is because it will stain the display area and cause poor insulation between terminal pins, and might affect display’s electrical characteristics furthermore.

4) Do not use any harmful chemicals such as acetone, toluene, and isopropyl alcohol to clean display’s surfaces.

5) Please use soft cloth or absorbent cotton with ethanol to clean the display by gently wiping. Moreover, when wiping the display, please wipe it by horizontal or vertical direction instead of circling to prevent leaving scars on the display’s surface, especially polarizer.

6) Please wipe any unknown liquids immediately such as saliva, water or dew on the display to avoid color fading or any permanently damages.

7) Maximum pressure to the surface of the display must be less than 410 x 1,96 Pa. If the area of adding pressure is less than 1 2cm , the maximum pressure must be less than 1.96N.

12.3 PRECAUTIONS OF OPERATING

1) Please input signals and voltages to the displays according to the values defined in the section of electrical characteristics to obtain the best performance. Any voltages over than absolute maximum rating will cause permanent damages to this display. Also, any timing of the signals out of this specification would cause unexpected performance.

2) When the display is operating at significant low temperature, the response time will be slower than it at 25 C . In high temperature, the color will be slightly dark and blue compared to original pattern. However, these are temperature-related phenomenon of LCD and it will not cause permanent damages to the display when used within the operating temperature.

3) The use of screen saver or sleep mode is recommended when static images are likely for long periods of time. This is to avoid the possibility of image sticking.

4) Spike noise can cause malfunction of the circuit. The recommended limitation of spike noise is no bigger than 100 mV.


12.4 PRECAUTIONS of STORAGE

If the displays are going to be stored for years, please be aware the following notices.

1) Please store the displays in a dark room to avoid any damages from sunlight and other sources of UV light.

2) The recommended long-term storage temperature is between 10 C ~35 C and 55%~75% humidity to avoid causing bubbles between polarizer and LCD glasses, and polarizer peeling from LCD glasses.

3) It would be better to keep the displays in the container, which is shipped from KOE, and do not unpack it.

4) Please do not stick any labels on the display surface for a long time, especially on the polarizer.


13. DESIGNATION of LOT MARK 1) The lot mark is showing in Fig.13.1. First 4 digits are used to represent production lot, T represented

made in Taiwan, and the last 6 digits are the serial number.

2) The tables as below are showing what the first 4 digits of lot mark are shorted for.

Lot Mark Lot MarkMonth Month

01

02

03

04

05

06

07

08

09

10

11

12

Jan.

Feb.

Mar.

Apr.

May

Jun.

Jul.

Aug.

Sep.

Oct.

Nov.

Dec.

Week1~7 days

8~14 days

15~21 days

22~28 days

29~31 days

1

2

3

4

5

Lot Mark

3) Except letters I and O, revision number will be shown on lot mark and following letters A to Z.

4) The location of the lot mark is on the back of the display shown in Fig. 13.2.

Fig. 13.2


TX20D200VM2BAB 4123T (5D) 123456

REV:A

A L L T E C H N O LO G I E S . A L L CO M P E T E N C I E S . O N E S P E C I A L I S T.

w w w . d a t a - m o d u l . c o m

More information and worldwide locations can be found at

DATA MODUL AG

Landsberger Straße 322 DE-80687 Munich Phone: +49-89-56017-0

DATA MODUL WEIKERSHEIM GMBH

Lindenstraße 8 DE-97990 Weikersheim Phone: +49-7934-101-0

koe tx20d200vm2bab tft-display distributed by data modul … · supply voltage vdd-0.5 5.0 v -...

Documents