kgs-510f ver.c installation guide · -1-kgs-510f ver.c web smart 6-port gigabit ethernet switch...

-1-

KGS-510F Ver.CWeb Smart 6-Port Gigabit Ethernet Switch

with Fiber Connectivity

KGS-510F-CSoftware v1.07 or later

Installation Guide

DOC.120214

-2-

(C) 2012 KTI Networks Inc. All rights reserved. No part of this documentation may be reproducedin any form or by any means or used to make any directive work (such as transla-tion or transformation) without permission from KTI Networks Inc.

KTI Networks Inc. reserves the right to revise this documentation and to make changes in contentfrom time to time without obligation on the part of KTI Networks Inc. to provide notification of suchrevision or change.

For more information, contact:

United States KTI Networks Inc.P.O. BOX 631008Houston, Texas 77263-1008

Phone: 713-2663891Fax: 713-2663893E-mail: [email protected]: http://www.ktinet.com/

International Fax: 886-2-26983873E-mail: [email protected]: http://www.ktinet.com.tw/

-3-

The information contained in this document is subject to change without prior notice. Copyright (C). AllRights Reserved.

TRADEMARKSEthernet is a registered trademark of Xerox Corp.

WARNING:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment. This equipment generates,uses, and can radiate radio frequency energy and if not installed and used in accordance with theinstruction manual may cause harmful interference in which case the user will be required to correct theinterference at his own expense.NOTICE:(1) The changes or modifications not expressively approved by the party responsible for compliancecould void the user's authority to operate the equipment.(2) Shielded interface cables and AC power cord, if any, must be used in order to comply with theemission limits.

CISPR A COMPLIANCE:This device complies with EMC directive of the European Community and meets or exceeds the followingtechnical standard.EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of InformationTechnology Equipment. This device complies with CISPR Class A.WARNING: This is a Class A product. In a domestic environment this product may cause radio interfer-ence in which case the user may be required to take adequate measures.

CE NOTICE

Marking by the symbol indicates compliance of this equipment to the EMC directive of the Euro-pean Community. Such marking is indicative that this equipment meets or exceeds the following techni-cal standards:

EN 55022: Limits and Methods of Measurement of Radio Interference characteristics of InformationTechnology Equipment.

EN 50082/1:Generic Immunity Standard -Part 1: Domestic Commercial and Light Industry.

EN 60555-2: Disturbances in supply systems caused by household appliances and similar electricalequipment - Part 2: Harmonics.

-4-

Table of Contents

1. Introduction .................................................................................................. 61.1 Features ...................................................................................................................71.2 Product Panels .........................................................................................................71.3 LED Indicators ..........................................................................................................81.4 Specifications ...........................................................................................................8

2. Installation .................................................................................................. 102.1 Unpacking ............................................................................................................... 102.2 Safety Cautions ...................................................................................................... 102.3 Mounting the Switch ................................................................................................ 102.4 Applying Power ........................................................................................................ 112.5 Reset Button .......................................................................................................... 112.6 Making UTP Connections ....................................................................................... 122.7 Making Fiber Connection ........................................................................................ 132.8 LED Indication ........................................................................................................ 142.9 Configuring IP Address and Password for the Switch ............................................. 14

3. Advanced Functions .................................................................................. 153.1 Abbreviation ............................................................................................................. 153.2 QoS Function .......................................................................................................... 163.2.1 Packet Priority Classification ................................................................................ 173.2.2 Priority Class Queues .......................................................................................... 173.2.3 Egress Service Policy .......................................................................................... 173.3 VLAN Function ......................................................................................................... 183.3.1 VLAN Operation .................................................................................................... 183.3.2 Ingress Rules ....................................................................................................... 183.3.2.1 802.1Q Tag Aware Per port setting .................................................................... 183.3.2.2 Keep Tag Per port setting .................................................................................. 183.3.2.3 Drop Untag Per Port Setting .............................................................................. 193.3.2.4 Drop Tag Per Port Setting .................................................................................. 193.3.3 Ingress Default Tag Per Port Setting..................................................................... 193.3.4 Packet Tag Information ......................................................................................... 193.3.5 VLAN Group Table Configuration ........................................................................... 203.3.6 VLAN Classification............................................................................................... 203.3.7 Packet Forwarding................................................................................................ 203.3.8 Egress Tagging Rules .......................................................................................... 213.3.8.1 Egress Settings ................................................................................................. 213.3.9 Summary of VLAN Function ................................................................................. 213.4 802.1X Authentication .............................................................................................. 21

4. Web Management ....................................................................................... 23

-5-

4.1 Start Browser Software and Making Connection ..................................................... 234.2 Login to the Switch Unit ........................................................................................... 234.3 Main Management Menu .......................................................................................... 244.4 System .................................................................................................................... 264.4.1 Management VLAN ............................................................................................... 284.5 Ports ........................................................................................................................ 294.6 VLANs ..................................................................................................................... 314.6.1 Port-based VLAN Mode ......................................................................................... 324.6.2 Port-based VLAN ISP Mode .................................................................................. 334.6.3 Advanced VLAN Mode ........................................................................................... 344.6.3.1 Ingress Default Tag ............................................................................................ 354.6.3.2 Ingress Settings................................................................................................. 364.6.3.3 Egress Settings ................................................................................................. 374.6.3.4 VLAN Groups ..................................................................................................... 394.6.4 Important Notes for VLAN Configuration................................................................ 404.7 LACP .......................................................................................................................414.8 RSTP ...................................................................................................................... 424.9 802.1X Configuration ............................................................................................... 434.9.1 802.1X Statistics................................................................................................... 454.9.2 802.1X Re-authentication Parameters.................................................................. 464.10 IGMP Snooping ...................................................................................................... 474.11 Mirroring .................................................................................................................484.12 Quality of Service .................................................................................................. 494.12.1 802.1p Mapping................................................................................................... 504.12.2 DSCP Mapping ................................................................................................... 514.12.3 QoS Service Policy ............................................................................................ 524.13 Storm Control ........................................................................................................ 534.14 Statistics Overview................................................................................................ 544.15 Detailed Statistics .................................................................................................. 554.16 LACP Status .......................................................................................................... 564.17 RSTP Status ......................................................................................................... 584.18 IGMP Status .......................................................................................................... 604.19 Ping ....................................................................................................................... 614.20 Reboot System ..................................................................................................... 624.21 Restore Default ..................................................................................................... 624.22 Update Firmware ................................................................................................... 624.23 Configuration File Transfer .................................................................................... 634.24 Logout ................................................................................................................... 63

5. SNMP Support ............................................................................................ 64

Appendix. Factory Default Settings............................................................... 65

-6-

1. IntroductionThe KGS-510F-C is a managed 6-port Gigabit Ethernet switch which is featured with five copper ports,one mini-GBIC (SFP) port and the following advantages in a small footprint box:

Plug and PlayThe switch is shipped with factory default configuration which behaves like an unmanaged Gigabitswitch for workgroup. It provides five 10/100/1000Mbps copper ports for connections to Ethernet, FastEthernet, and Gigabit Ethernet devices. With the featured auto-negotiation function, the switch candetect and configure the connection speed and duplex automatically. The switch also provides autoMDI/MDI-X function, which can detect the connected cable and switch the transmission wire pair andreceiving pair automatically. This auto-crossover function can simplify the type of network cables used.

Fiber ConnectivityThe mini-GBIC (SFP) port can be installed with an optional SFP optical fiber transceiver to support oneGigabit fiber connection when needed.

Web ManagementThe switch is embedded with an Http server which provides management functions for advancednetwork functions including Port Control, Quality of Service, and Virtual LAN functions. The manage-ment can be performed via Web browser based interface over TCP/IP network.

Quality of ServiceFor advanced application, the switch is featured with powerful Quality of Service (QoS) function whichcan classify the priority for received network frames based on the ingress port and frame contents.Furthermore, many service priority policies can be configured for egress operation in per-port basis.

Virtual LAN (VLAN)For increasing Tagged VLAN applications, the switch is also featured with powerful VLAN function tofulfill the up-to-date VLAN requirements. The switch supports both port-based VLAN and taggedVLAN in per-port basis.

-7-

1.1 FeaturesProvides 5 10/100/1000Mbps Gigabit Ethernet ports and 1 SFP portProvides in-band web-based management interfaceAll copper ports support auto-negotiation and auto-MDI/MDI-X detectionProvides full wire speed forwardingSupports 802.3x flow control for full-duplex and backpressure for half-duplexProvides port status, statistic monitoring and control functionSupports port-based and 802.1Q Tag-based VLANProvides QoS functionProvides link aggregation (port trunking) function with LACP supportProvides port mirroring functionProvides 802.1X authentication for port accessSupports 802.1w RSTP and 802.1D STPProvides packet storm control functionConfiguration file backup and restoreIn-band embedded firmware upgrade function

1.2 Product PanelsThe following figure illustrates the front panel and rear panel of the switch:

Front panel

Rear panel

-8-

1.3 LED IndicatorsLED Function

POWER Power status

LNK/1000M/ACT Network port 1000M link status (Port 1 - Port 5)



P6 LNK Port 6 1000M link status

P6 OL Port 6 optical link status

1.4 Specifications10/100/1000 Copper Ports

Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,

IEEE 802.3u 1000Base-T

Connectors Shielded RJ-45 jacks

Pin assignments Auto MDI/MDI-X detection

Configuration Auto-negotiation or software control

Transmission rate 10Mbps, 100Mbps, 1000Mbps

Duplex support Full/Half duplex

Network cable Cat.5 UTP

1000Mbps Mini-GBIC Fiber Port

Compliance IEEE 802.3z 1000Base-SX/LX (mini-GBIC)

Connectors SFP for optional SFP type fiber transceivers

Configuration Auto/Forced, 1000Mbps, Full duplex

Transmission rate 1000Mbps

Network cables MMF 50/125 60/125, SMF 9/125

Eye safety IEC 825 compliant

Switch Functions

MAC Addresses Table 8K entries

Forwarding & filtering Non-blocking, full wire speed

Switching technology Store and forward

Maximum packet length 1526 bytes (Jumbo frame support disabled) 9.6K bytes (Jumbo frame)

Flow control IEEE 802.3x pause frame base for full duplex operationBack pressure for half duplex operation

VLAN function Port-based VLAN and IEEE 802.1Q Tag-based VLAN

4095 VLANs supported, IVL support

QoS function Port-based, 802.1p-based, IP DSCP-based

-9-

Port control Port configuration control via software management

Storm control Broadcast, Multicast storm protection control via software management

Aggregation Link aggregation (port trunking)

Port Mirroring Mirror received frames to a sniffer port

Software Management Functions

Interfaces Web browser

Management objects System configuration - IP settings, Name, Password

Port configuration control and status, VLAN function settings

Port Link Aggregation function settings

Link Aggregation LACP settings, RSTP settings

802.1X port access control, Port mirroring settings

QoS function settings, Storm protection control settings

Port statistic, LACP status, RSTP status

Configuration file backup and restore

Reboot, restore factory default, update firmware

DC Power Input

Interfaces DC Jack ( -D 6.3mm / + D 2.0mm)

Operating Input Voltages +5V - 12VDC(+/-5%)

Power consumption 5W max. @+5V

Mechanical

Dimension (base) 144 x 104.5 x 26 mm

Housing Enclosed metal with no fan

Mounting Desktop mounting, wall mounting

Environmental

Operating Temperature Typical 0oC ~ 40oC

(* The operating temperature range of the bundled power adapter maydiffer from the temperature range of the main device.)

Storage Temperature -20oC ~ 70oC

Relative Humidity 10% ~ 90%

Electrical Approvals

FCC Part 15 rule Class A

CE EMC, CISPR22 Class A

-10-

2. Installation2.1 UnpackingThe product package contains:

• The switch unit• One power adapter• One product CD-ROM

2.2 Safety CautionsTo reduce the risk of bodily injury, electrical shock, fire, and damage to the product, observe the follow-ing precautions.

• Do not service any product except as explained in your system documentation.

• Opening or removing covers may expose you to electrical shock.

• Only a trained service technician should service components inside these compartments.

• If any of the following conditions occur, unplug the product from the electrical outlet and replacethe part or contact your trained service provider:- The power cable, extension cable, or plug is damaged.- An object has fallen into the product.- The product has been exposed to water.- The product has been dropped or damaged.- The product does not operate correctly when you follow the operating instructions.

• Do not push any objects into the openings of your system. Doing so can cause fire or electricshock by shorting out interior components.

• Operate the product only from the type of external power source indicated on the electricalratings label. If you are not sure of the type of power source required, consult your serviceprovider or local power company.

2.3 Mounting the SwitchThe switch can be mounted on a desktop or shelf or a wall. Make sure that there is proper heatdissipation from and adequate ventilation around the device. Do not place heavy objects on the device.

-11-

2.4 Applying PowerBefore you begin the installation, check the AC voltage of your area. The AC power adapter which is usedto supply the DC power for the unit should have the AC voltage matching the commercial power voltage inyour area.

The AC Power Adapter Specifications

AC input power: AC power voltage of your area, options -Rated AC120V/60Hz DC7.5V 1A / DC5V 2A / DC12V 0.8ARated AC230V/50Hz DC7.5V 1A / DC5V 2A / DC12V 0.8ARated AC100V/50-60Hz DC7.5V 1A / DC5V 2A / DC12V 0.8ARated AC100V/50-60Hz DC5V 1A / DC12V 0.8ARated AC240V/50Hz DC7.5V 1A / DC5V 2A / DC12V 0.8A

Steps to apply the power to the product are:

1. Connect power adapter DC plug to the DC input jack located on the back of the unit beforeconnecting to the AC outlet.

2. Connect the power adapter to the AC outlet.3. Check Power LED indication.

Note: Before you begin the installation, check the AC voltage of your area. The AC poweradapter which is used to supply the DC power for the unit should have the AC voltagematching the commercial power voltage in your area.

2.5 Reset ButtonThe reset button is used to perform a reset to the switch. It is not used in normal cases and can be usedfor diagnostic purpose. If any network hanging problem is suspected, it is useful to push the button toreset the switch without turning off the power. Check whether the network is recovered.

The button can also be used to restore the software configuration settings to factory default values.

The operations are:

Operation Function

Press the button more than 5 seconds when power up Restore all factory default settingsPress the button and release during switch operation Reboot the switch

-12-

2.6 Making UTP ConnectionsThe 10/100/1000 RJ-45 copper ports supports the following connection types and distances:

Network Cables10BASE-T: 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm100BASE-TX: 2-pair UTP Cat. 5, EIA/TIA-568B 100-ohm1000BASE-T: 4-pair UTP Cat. 5 or higher (Cat.5e is recommended), EIA/TIA-568B 100-ohmLink distance: Up to 100 meters

Auto MDI/MDI-X FunctionThis function allows the port to auto-detect the twisted-pair signals and adapts itself to form a validMDI to MDI-X connection with the remote connected device automatically. No matter a straightthrough cable or crossover cable is connected, the ports can sense the receiving pair automatically andconfigure itself to match the rule for MDI to MDI-X connection. It simplifies the cable installation.

Auto-negotiation FunctionThe ports are featured with auto-negotiation function and full capability to support connection to anyEthernet devices. The port performs a negotiation process for the speed and duplex configuration withthe connected device automatically when each time a link is being established. If the connected deviceis also auto-negotiation capable, both devices will come out the best configuration after negotiationprocess. If the connected device is incapable in auto-negotiation, the switch will sense the speed anduse half duplex for the connection.

Port Configuration ManagementFor making proper connection to an auto-negotiation incapable device, it is suggested to use port con-trol function via software management to set forced mode and specify speed and duplex mode whichmatch the configuration used by the connected device.

-13-

2.7 Making Fiber ConnectionThe SFP slot must be installed with an SFP fiber transceiver for making fiber connection. Yourswitch may come with one SFP transceiver pre-installed when it is shipped.

Installing SFP Fiber TransceiverTo install an SFP fiber transceiver into SFP slot, the steps are:

1. Turn off the power to the switch.2. Insert the SFP fiber transceiver into the SFP slot. Normally, a bail is provided for every SFP

transceiver. Hold the bail and make insertion.3. Until the SFP transceiver is seated securely in the slot, place the bail in lock position.

Connecting Fiber CablesLC connectors are commonly equipped on most SFP transceiver modules. Identify TX and RXconnector before making cable connection. The following figure illustrates a connection examplebetween two fiber ports:

Make sure the Rx-to-Tx connection rule is followed on the both ends of the fiber cable.

Network CablesMultimode (MMF) - 50/125, 62.5/125Single mode (SMF) - 9/125

-14-

2.8 LED Indication

LED Function State Interpretation

POWER Power status ON The power is supplied to the switch.OFF The power is not supplied to the switch.

LNK/1000M/ACT Port link status ON A 1000M link is established. (No traffic)BLINK Port link is up and there is traffic.OFF Port link is down.



P6 LNK Port6 link status ON A 1000M link is established on Port 6.BLINK Port 6 link is up and there is traffic.OFF Port 6 link is down.

P6 OL Port6 optical link ON Optical signal is detected on Port 6.OFF No optical signal is detected on Port 6.

2.9 Configuring IP Address and Password for the SwitchThe switch is shipped with the following factory default settings for software management :

Default IP address of the switch : 192.168.0.2 / 255.255.255.0

The IP Address is an identification of the switch in a TCP/IP network. Each switch should be desig-nated a new and unique IP address in the network. Refer to Web management interface for SystemConfiguration.

The switch is shipped with factory default password 123 for software management.The password is used for authentication in accessing to the switch via Http web-based interface. Forsecurity reason, it is recommended to change the default settings for the switch before deploying it toyour network. Refer to Web management interface for System Configuration.

-15-

3. Advanced FunctionsTo help a better understanding about the software management interfaces, this chapter describes someadvanced functions provided by the switch.

3.1 AbbreviationIngress Port : Ingress port is the input port on which a packet is received.

Egress Port : Egress port is the output port from which a packet is sent out.

IEEE 802.1Q Packets : A packet which is embedded with a VLAN Tag field

VLAN Tag : In IEEE 802.1Q packet format, 4-byte tag field is inserted in the original Ethernet framebetween the Source Address and Type/Length fields. The tag is composed of :

#of bits 16 3 1 12Frame field TPID User priority CFI VID

TPID : 16-bit field is set to 0x8100 to identify a frame as an IEEE 802.1Q tagged packet

User Priority : 3-bit field refer to the 802.1p priority

CFI : The Canonical Format Indicator for the MAC address is a 1 bit field.

VID : VLAN identifier, 12-bit field identifies the VLAN to which the frame belongs to.

Untagged packet : A standard Ethernet frame with no VLAN Tag field

Priority-tagged packet : An IEEE 802.1Q packet which VID filed value is zero (VID=0)

VLAN-Tagged packet : An IEEE 802.1Q packet which VID filed value is not zero (VID<>0)

PVID (Port VID)PVID is the default VID of an ingress port. It is often used in VLAN classification for untaggedpackets. It is also often used for egress tagging operation.

DSCP : Differentiated Service Code Point, 6-bit value field in an IP packet

VLAN Table lookup : The process of searching VLAN table to find a VLAN which matches thegiven VID index

MAC address table lookup : The process of searching MAC address table to find a MAC entrywhich matches the given destination MAC address and the port where the MAC address is located

Packet forwarding : also known as packet switching in a network switch based on MAC addresstable and VLAN table information

VLAN forwarding : the operation that a packet is forwarded to an egress destination port based onVLAN table information

VLAN group : configuration information about a VLAN which can be recognized in the switch. Theinformation includes a VID associated to the VLAN, member ports, and some special settings.

-16-

3.2 QoS FunctionThe switch provides a powerful Quality of Service (QoS) function to guide the packet forwarding infour priority classes. The versatile classification methods can meet most of the application needs. Thefollowing figure illustrates the QoS operation flow when a packet received on the ingress port until it istransmitted out from the egress port:

-17-

3.2.1 Packet Priority ClassificationEach received packet is examined and classified into one of four priority classes, Class 3, Class 2,Class 1 and Class 0 upon reception. The switch provides the following classification methods:

802.1p classification : use User Priority tag value in the received IEEE 802.1Q packet to map to onepriority classDSCP classification : use DSCP value in the received IP packet to map to one priority classPort-based classification : used when 802.1p and DSCP are disabled or fail to be applied

They all can be configured to be activated or not. More than one classification methods can be enabledat the same time. However, 802.1p classification is superior than DSCP classification.

802.1p mapping tables : Each ingress port has its own mapping table for 802.1p classification.DSCP mapping table : All ingress ports share one DSCP mapping table for DSCP classification.Default port priority : A port default priority class is used when port-based classification is applied

All configuration settings are in per port basis except that DSCP mapping table is global to all ports. Areceived packet is classified into one of four priority class before it is forwarded to an egress port.

3.2.2 Priority Class QueuesEach egress port in the switch is equipped with four priority class egress queues to store the packetsfor transmission. A packet is stored into the class queue which is associated to the classified priorityclass. For example, a packet is stored into Class 3 egress queue if it is classified as priority Class 3.

3.2.3 Egress Service PolicyEach port can be configured with an egress service policy to determine the transmission priority amongfour class queues. By default, higher class number has higher priority than the lower class numbers.

Four policies are provided for selection as follows:

• Strict priority : Packets in high priority class queue are sent first until the queue is empty• Weighted ratio priority Class 3:2:1:0 = 4:3:2:1 : four queues are served in 4:3:2:1 ratio• Weighted ratio priority Class 3:2:1:0 = 5:3:1:1 : four queues are served in 5:3:1:1 ratio• Weighted ratio priority Class 3:2:1:0 = 1:1:1:1 : four queues are served equally

Strict priority policy lets high priority class queue is served first until it is empty. Lower priority queuemay not get any service (or egress bandwidth) when higher priority traffic is heavy for long time. Threeweighted ratio policies are provided to resolve such problem. Four class queues are served in weightedround robin basis. Every priority class can get a guaranteed ratio for the egress bandwidth.

-18-

3.3 VLAN FunctionThe switch supports port-based VLAN, 802.1Q Tag VLAN and eight VLAN groups.

3.3.1 VLAN OperationThe following figure illustrates the basic VLAN operation flow beginning from a packet received on aningress port until it is transmitted from an egress port.

The following sections describe the VLAN processes and Advanced VLAN mode settings providedby the switch. A global setting means the setting is applied to all ports of the switch. A per port settingmeans each port can be configured for the setting respectively.

3.3.2 Ingress RulesWhen a packet is received on an ingress port, the ingress rules are applied for packet filtering andpacket tag removal. The related Ingress port settings are:

3.3.2.1 802.1Q Tag Aware Per port settingTag-aware -802.1Q Tag Aware mode is used. The switch examines the tag content of every

received packets. For a VLAN tagged packet, the packet VLAN tag data is retrievedas packet tag information for VLAN classification and egress tagging operation. Foruntagged packet and priority-tagged packet, port-based mode is used.

Tag-ignore - Port-based mode is used. The switch ignores the tag content of every receivedpackets. Ingress Port Default Tag is always used as packet tag information for VLANclassification.

3.3.2.2 Keep Tag Per port settingEnable - The VLAN tag in the received VLAN tagged packet will be kept as it is and is not

stripped in whole forwarding operation.

Disable - The VLAN tag data in the received VLAN tagged packet is stripped (removed).

-19-

3.3.2.3 Drop Untag Per Port SettingEnable - All untagged packets and priority-tagged packets are dropped. A priority-tagged packet

is treated as an untagged packet in this switch. Only VLAN-tagged packets areadmitted.

Disable - Disable Untagged packet filtering

3.3.2.4 Drop Tag Per Port SettingEnable - All VLAN-tagged packets are dropped. A priority-tagged packet is treated as an

untagged packet in this switch. Only untagged packets are admitted.

Disable - Disable VLAN-tagged packet filtering

3.3.3 Ingress Default Tag Per Port SettingEach port can be configured with one Ingress Default Tag. This ingress port default tag is used wheningress port is in Tag-ignore mode or for the received untagged packets in Tag-aware mode. TheIngress Default Tag includes PVID, CFI and User Priority configuration.

When Ingress port default tag is used, it is copied as packet associated Packet Tag Information forVLAN classification. The PVID is used as index to one VLAN group in VLAN group table.

3.3.4 Packet Tag InformationUnder VLAN process, every packet is associated with one Packet Tag information in packet forward-ing operation. The tag information includes VID, CFI and User Priority data and is used for twopurposes:

• The VID in tag is used as index for VLAN classification.• The tag is used for egress tag insertion if egress tagging is enabled.

The following table lists how the Packet Tag information is generated:

Tag Aware setting Received Packet Type Packet Tag information sourceTag-ignore Untagged packet Ingress Port Default TagTag-ignore Priority-tagged packet Ingress Port Default TagTag-ignore VLAN-tagged packet Ingress Port Default Tag

Tag-aware Untagged packet Ingress Port Default TagTag-aware Priority-tagged packet Ingress Port Default TagTag-aware VLAN-tagged packet Received packet VLAN Tag

-20-

3.3.5 VLAN Group Table ConfigurationThe switch provides a table of eight VLAN groups to support up to eight VLANs at the same time.Each VLAN group is associated to one unique VLAN. The table is referred for VLAN classification.

A VLAN group contains the following configuration settings:

VID : 12-bit VLAN Identifier index to the VLAN to which the group is associatedMember Ports : the admitted egress ports for packets belonging to this VLANSource Port Check : the ingress port of the packet must also be the member port of this VLAN.Otherwise, the packet is discarded.

3.3.6 VLAN ClassificationVLAN classification is a process to classify a VLAN group to which a received packet belongs. TheVID of the generated Packet Tag information associated to the received packet is used as an index forVLAN group table lookup. The VID matched VLAN group will be used for packet forwarding. If nomatched VLAN group is found in table lookup, the packet is dropped.

Refer to section 3.2.4 for details about how the Packet Tag information is generated.

The member ports specified in the matched VLAN group are the admitted egress port range for thepacket. The packet will never be forwarded to other ports which are not in the member ports.

The Source Port Check setting of the matched VLAN group is also referred. If it is enabled, theingress port will be checked whether it is a member port of this group.

3.3.7 Packet ForwardingThe forwarding is a process to forward the received packet to one or more egress ports. The processuses the following information as forwarding decision:

• Member ports of the matched VLAN group : the egress port range for forwarding• Source Port Check setting of the matched VLAN group : check ingress port membership• The packet destination MAC address : for MAC address table loop up• The switch MAC address table : to find the associated port where a MAC address is learned

If the MAC address table lookup is matched and the learned port is the VLAN member port, thepacket is forwarded to the port (egress port). If the lookup failed, the switch will broadcast the packetto all member ports.

-21-

3.3.8 Egress Tagging RulesEgress Tagging rules are used to make change to the packet before it is stored into egress queue of anegress port. Three egress settings are provided for each port and are described as follows:

3.3.8.1 Egress SettingsInsert Tag (per port setting)Enable - Insert the Tag data of the associated Packet Tag information into the packet

Disable - No tagging is performed.

Untagging Specific VID (per port setting)Enable - No tag insertion if the VID data of the associated Packet Tag information matches the

Untagged VID configured in next setting even [Insert Tag] is enabled.

Disable - This rule is not applied.

3.3.9 Summary of VLAN FunctionVLAN ModesPort-based VLAN Mode : simple port-based 2-VLAN-groups modePort-based VLAN ISP Mode : simple port-based 5-VLAN-groups modeAdvanced VLAN Mode : Full VLAN configuration for port-based and Tag-based VLAN

Advanced VLAN ModeEgress Settings (per port) : [Tag Aware], [Keep Tag], [Drop Untag], [Drop Tag]Ingress Default Tag (per port) : [PVID], [CFI], [User Priority]VLAN Groups (global) : 8 VLAN groupsVLAN Group Settings (per group) : [VID], [Member Ports], [Source Port Check]Egress Settings : [Insert Tag], [Untagging Specific VID], [Untagged VID]

VLAN range supported : 1 ~ 4095 (eight VLANs at the same time)

[PVID] [VID] [Untagged VID] value range : 1 ~ 4095

3.4 802.1X AuthenticationFor some IEEE 802 LAN environments, it is desirable to restrict access to the services offered by theLAN to those users and devices that are permitted to make use of those services. IEEE 802.1X Port-based network access control function provide a means of authenticating and authorizing devices at-tached to a LAN port that has point-to-point connection characteristics, and of preventing access to thatport in cases in which the authentication and authorization process fails. The 802.1X standard relies onthe client to provide credentials in order to gain access to the network. The credentials are not based ona hardware address. Instead, they can be either a username/password combination or a certificate. Thecredentials are not verified by the switch but are sent to a Remote Authentication Dial-In User Service(RADIUS) server, which maintains a database of authentication information. 802.1X consists of threecomponents for authentication exchange, which are as follows:

-22-

An 802.1X authenticator: This is the port on the switch that has services to offer to an end device,provided the device supplies the proper credentials.

An 802.1X supplicant: This is the end device; for example, a PC that connects to a switch that isrequesting to use the services (port) of the device. The 802.1X supplicant must be able to respond tocommunicate.

An 802.1X authentication server: This is a RADIUS server that examines the credentials provided tothe authenticator from the supplicant and provides the authentication service. The authentication server is respon-sible for letting the authenticator know if services should be granted.

The 802.1X authenticator operates as a go-between with the supplicant and the authentication server toprovide services to the network. When a switch is configured as an authenticator, the ports of theswitch must then be configured for authorization. In an authenticator-initiated port authorization, a clientis powered up or plugs into the port, and the authenticator port sends an Extensible AuthenticationProtocol (EAP) PDU to the supplicant requesting the identification of the supplicant. At this point in theprocess, the port on the switch is connected from a physical standpoint; however, the 802.1X processhas not authorized the port and no frames are passed from the port on the supplicant into the switchingengine. If the PC attached to the switch did not understand the EAP PDU that it was receiving from theswitch, it would not be able to send an ID and the port would remain unauthorized. In this state, the portwould never pass any user traffic and would be as good as disabled. If the client PC is running the802.1X EAP, it would respond to the request with its configured ID. (This could be a username/password combination or a certificate.)

After the switch, the authenticator receives the ID from the PC (the supplicant). The switch thenpasses the ID information to an authentication server (RADIUS server) that can verify the identifica-tion information. The RADIUS server responds to the switch with either a success or failure message.If the response is a success, the port will be authorized and user traffic will be allowed to pass throughthe port like any switch port connected to an access device. If the response is a failure, the port willremain unauthorized and, therefore, unused. If there is no response from the server, the port will alsoremain unauthorized and will not pass any traffic.

-23-

4. Web ManagementThe switch features an http server which can serve the management requests coming from any webbrowser software over TCP/IP network.

Web BrowserCompatible web browser software with JAVA script supportMicrosoft Internet Explorer 4.0 or later

Set IP Address for the System UnitBefore the switch can be managed from a web browser software, make sure a unique IP address isconfigured for the switch.

4.1 Start Browser Software and Making ConnectionStart your browser software and enter the IP address of the switch unit to which you want to connect.The IP address is used as URL for the browser software to search the device.

URL : http://xxx.xxx.xxx.xxx/

Factory default IP address : 192.168.0.2

4.2 Login to the Switch UnitWhen browser software connects to the switch unit successfully, a Login screen is provided for you tologin to the device as follows:

The switch will accept only one successful management connection at the same time. The other con-nection attempts will be prompted with a warning message.

A new connection will be accepted when the current user logout successfully or auto logout by theswitch due to no access for time out of 3 minutes.

System Configuration is displayed after a successful login.

-24-

4.3 Main Management Menu

ConfigurationSystem Switch information, system and IP related settings

Ports Port link status, port operation mode configuration

VLAN VLAN related configuration

LACP LACP confguration for port link aggregation

RSTP RSTP (Rapid spanning tree protocol) related configuration

802.1X 802.1X authentication related configuration

IGMP Snooping IGMP snooping configuration

Mirroring Port mirroring related configuration

QoS Quality of Service related configuration

Storm Control Packet Storm protection control configuration

-25-

MonitoringStatistics Overview List simple statistics for all ports

Detailed Statistics List detailed statistics for all ports

LACP Status LACP port status

RSTP Status RSTP protocol status

IGMP Status IGMP snooping status

Ping Ping command from the switch to other IP devicesMaintenanceReboot System Command to reboot the switch

Restore Default Command to restore the switch with factory default settings

Update Firmware Command to update the switch firmware

Conrfiguration File Transfer Upload and save configuration file

Logout Command to logout from the switch management

-26-

4.4 System

-27-

Configuration Description

MAC Address The MAC address factory configured for the switchIt can not be changed in any cases.

S/W Version The firmware version currently running

H/W Version The hardware version currently operating

Active IP Address Currently used IP address for the switch management

Active Subnet Mask Currently used subnet mask for IP address for the switch management

Active Gateway Currently used gateway IP address for the switch management

DHCP Server Current IP address of the DHCP server

Lease Time Left The time left for the lease IP address currently used

DHCP Enabled Use DHCP to get dynamic IP address configuration for the switch

Fallback IP Address IP address used when DHCP mode is not enabled

Fallback Subnet Mask Subnet mask for IP address used when DHCP mode is not enabled

Fallback Gateway Default gateway IP address used when DHCP mode is not enabled

Management VLAN Set management VLAN information- VID VLAN ID configured for web management to the switch- CFI CFI value for web reply packets from the switch- User priority Priority value for web reply packets from the switch

Name * Set the system name for this switch unit

Password Set new password

Inactivity Timeout (secs) Set timerout for auto-logout timer

SNMP enabled Enable SNMP agent

SNMP Trap destination The IP address of the SNMP trap manager

SNMP Read community The community allowed for the SNMP [get] message

SNMP Write community The community allowed for the SNMP [set] message

SNMP Trap community The community used for the SNMP trap messages sent by the switch

[Apply] Click to apply the configuration change

[Refresh] Click to refresh current configuration

Note:1. It is suggested to give each switch unit a system name as an alternative unique identifica-

tion beside IP address.2. Setting change of DHCP mode takes effective in next bootup.

-28-

4.4.1 Management VLANManagement VLAN settings allow administrator to access the switch and perform the switch manage-ment over a dedicated VLAN.

The following rules are applied with the Management VLAN:

1. If the VLAN function is disabled, Management VLAN settings are ignored and no VLANlimitation is applied in accessing the switch web management interface. The switch web (http)server only accepts untagged management packets and replies untagged packets to the manage-ment host.

2. If [Management VLAN - VID] settings is zero, no VLAN limitation is applied in accessing theswitch web management interface. The switch web (http) server only accepts untagged manage-ment packets and replies untagged packets to the management host.

3. If [Management VLAN - VID] settings is not zero, The switch web (http) server only acceptstagged management packets matched [Management VLAN -VID] and replies tagged packetswith tag composed of [Management VLAN] VID, CFI and User Priority settings to the manage-ment host. The egress port will also be limited in the member ports of the matched VLAN group.

Summary of the rules:

VLAN Function Management VID Switch Embedded Web Server operationVLAN disabled Ignore Accept untagged web packets

Reply untagged packetsNo VLAN group member checking

VLAN enabled VID=0 Accept untagged web packetsReply untagged packetsNo VLAN group member checking

VLAN enabled VID<>0 Accept matched tagged web packets only( 1 ~ 4095) Reply tagged packets with the configured tag

Matched VLAN group member checking

Notes:1. To apply management VLAN function, be sure to configure a VLAN group that matches the

management VID first.2. No matter how management VLAN is configured, login password authentication is still

required.

-29-

4.5 Ports

Configuration Function

Enable Jumbo Frames Select to enable jumbo frame support

Power Saving Mode Full - all the timeLink-up - saving when link upLink-dwon - saving when link downDisable - disable power saving

Port The port number

Link Speed and duplex status with green background - port is link onDown with red background - port is link down

-30-

Mode Select port operating modeDisabled - disable the port operation

Port 1 - Port 5Mode Auto-negotiation Speed capability Duplex capabilityAuto Speed Enable 10, 100, 1000M Full, Half10 Half Disable 10M Half10 Full Disable 10M Full100 Half Disable 100M Half100 Full Disable 100M Full1000 Full Enable 1000M Full

Port 6Mode Auto-negotiation Speed capability Duplex capabilityAuto speed Enable 1000M Full1000 Full Disable 1000M Full

Flow Control Set port flow control functionv - set to enable 802.3x pause flow control for ingress and egress



-31-

4.6 VLANs

VLAN Configuration Description

VLAN Disable Select to disable VLAN functionAll ports are allowed to communicate with each others freely withno VLAN limitation.

Port-based VLAN Mode Simple configuration for 2 port-based VLAN groups

Port-based VLAN ISP Mode Simple configuration for 5 port-based VLAN groups

Advance VLAN Mode Full VLAN configuration for port-based and Tag-based VLAN



-32-

4.6.1 Port-based VLAN Mode


Group 1, 2 Port-based VLAN group number

Member ports Select member ports for the group



[Back] Click to go back to upper menu

Operation in this mode:1. The member ports of two groups are allowed to overlap.2. The member ports in same group can communicate with other members only.3. No packet tag is examined.4. A received packet will not be modified (i.e. tagging or untagging) through VLAN operation till it

is transmitted.

-33-

4.6.2 Port-based VLAN ISP Mode


Joint port Select a port as the joint port for all 5 port-based VLAN groups




Example:If Port 6 is selected as the joint port, the 5 port-based VLAN groups are configured as follows auto-matically:

Group 1 - member [Port 1, Port 6]





Mode Operation :1. The joint port is the shared member port for all groups.2. Two member ports are configured in each group.3. The member ports in same group can communicate with other only.4. No packet tag is examined.5. A received packet will not be modified (i.e. tagging or untagging) through VLAN operation till it

is transmitted.

-34-

4.6.3 Advanced VLAN Mode


Ingress Default Tag Click to configure per port Ingress Default Tag settings

Ingress Settings Click to configure per port ingress settings

Egress Settings Click to configure per port egress settings

VLAN Groups Click to configure VLAN group table

-35-

4.6.3.1 Ingress Default Tag


Port Port number

PVID Port VID, VID for Ingress Default Tag1 ~ 4095 - decimal 12-bit VID value

CFI CFI for Ingress Default Tag0, 1 - 1-bit CFI value

User Priority User priority for Ingress Default Tag0 ~ 7 - decimal 3-bit value




PVID is used as index for VLAN classification (VLAN group table lookup) in one of the followingconditions:

1. Ingress port [Tag Aware] setting = Tag-ignore2. Ingress port [Tag Aware] setting = Tag-aware

and the received packet is untagged or priority-tagged

[PVID+CFI+User Priority] = Ingress Default Tag for the ingress portIt is used as the tag for insertion in egress tagging operation in one of the following conditions:

1. Ingress port [Tag Aware] setting = Tag-ignore, Egress port [Insert Tag] = Enable2. Ingress port [Tag Aware] setting = Tag-aware, Egress port [Insert Tag] = Enable

and the received packet is untagged or priority-tagged

-36-

4.6.3.2 Ingress Settings


Port Port number

Tag Aware Check tag data for every received packetTag-aware - set to activate Tag-based modeTag-ignore - set to use port-based mode and ignore any tag in packet

Keep Tag Tag is removed from the received packet if existsEnable - set to activate tag removal for VLAN-tagged packetsDisable - set to disable tag removal function

Drop Untag Drop all untagged packets and priority-tagged packetsEnable - drop untagged packets and priority-tagged packetsDisable - admit untagged packets and priority-tagged packets

Drop Tag Drop all VLAN-tagged packetsEnable - drop VLAN-tagged packetsDisable - admit VLAN-tagged packets



-37-

Note:1. Priority-tagged packet (VID=0) is treated as untagged packet in the switch.2. [Tag Aware] setting affects the index used for VLAN classification (VLAN table lookup).

The following table lists the index used:

Ingress [Tag Aware] settingReceived packet type Tag-ignore Tag-awareUntagged PVID PVIDPriority-tagged (VID=0) PVID PVIDVLAN-tagged (VID>0) PVID Packet tag VID

3. Both [Drop Untag] and [Drop Tag] are set to Disable to admit all packets.

4.6.3.3 Egress Settings

-38-


Port Port number

Insert Tag Activate tagging (Insert a tag to the packet)Enable - set to activate taggingDisable - set to disable tagging function

Untagging Specific VID No tag insertion if VID of packet tag information matches [UntaggedVID]Enable - set to enable this functionDisable - set to disable this function

Untagged VID VID for [Untagging Specific VID] setting1 ~ 4095 - decimal 12-bit VID value




The inserted tag sources when [Insert Tag] = Enable are listed as follows:

Received packet type [Tag Aware]=Tag-ignore [Tag Aware]=Tag-awareUntagged Ingress Default Tag Ingress Default TagPriority-tagged (VID=0) Ingress Default Tag Ingress Default TagVLAN-tagged (VID>0) Ingress Default Tag Packet own tag

-39-

4.6.3.4 VLAN Groups


Group Group number

VID VID of the VLAN to which this group is associated1 ~ 4095 - decimal 12-bit VID value

Member Ports Select the admitted egress ports for the packets belong to the VLANPort 1 ~ 6 - click to select

Source Port Check Check whether the ingress port is the member port of the VLANEnable - set to enable this check, the packet is dropped if ingress port isnot member port of the VLAN.Disable - set to disable this check




-40-

4.6.4 Important Notes for VLAN ConfigurationSome considerations should be checked in configuring VLAN settings:

1. Switch VLAN Mode selectionIt is suggested to evaluate your VLAN application first and plan your VLAN configurationcarefully before applying it. Any incorrect setting might cause network problem.

2. Aggregation/Trunking configurationMake sure the members of a link aggregation (trunk) group are configured with same VLANconfiguration and are in same VLAN group.

3. Double Tagged in Advanced VLAN ModeFor a received packet, Ingress port [Keep Tag] setting and Egress port [Insert Tag] setting areenabled at the same time. It will cause the packet double-tagged when egress. Although, it isoften applied in Q-in-Q provider bridging application. However, such condition should be avoidedin normal VLAN configuration. See table below:

Ingress port Egress port[Keep Tag] [Insert Tag] Received Packet Packet Transmitted Enable Enable Priority-tagged Double-tagged Enable Enable VLAN-tagged Double-tagged

-41-

4.7 LACP


Port Port number

Protocol Enabled Enable LACP support for the port

Key Value An integer value assigned to the port that determines which ports areaggregated into an LACP link aggregate. Set same value to the ports insame LACP link aggregate. Value: 1 ~ 255.Auto - key value is assigned by the system



Notes:1. This configuration is used to configure LACP aggregate groups.2. The ports with same key value are in same LACP aggregate group.3. The ports with Auto key are in same LACP aggregate group.

-42-

4.8 RSTP


System Priority The lower the bridge priority is the higher priority it has. Usually, the bridgewith the highest bridge priority is the root. Value: 0 ~ 61440

Hello Time Hello Time is used to determine the periodic time to send normal BPDUfrom designated ports among bridges. It decides how long a bridge shouldsend this message to other bridge to tell I am alive.

Max Age When the switch is the root bridge, the whole LAN will apply this settingas their maximum age time.

Forward Delay This figure is set by Root Bridge only. The forward delay time is defined asthe time spent from Listening state moved to Learning state and also fromLearning state moved to Forwarding state of a port in bridge.

Force Version Two options are offered for choosing STP algorithm.Compatible - STP (IEEE 802.1D)Normal - RSTP (IEEE 802.1w)

-43-

Aggregations Enabled to support port trunking in STP. It means a link aggregate istreated as a physical port in RSTP/STP operation.

Port Protocol Enabled Port is enabled to support RSTP/STP.

Port Edge An Edge Port is a port connected to a device that knows nothing aboutSTP or RSTP. Usually, the connected device is an end station. Edge Portswill immediately transit to forwarding state and skip the listening andlearning state because the edge ports cannot create bridging loops in thenetwork.

Port Path Cost Specifies the path cost of the port that switch uses to determine which portare the forwarding ports the lowest number is forwarding ports, the rage is1 ~ 200,000,000 and Auto. Auto means a default cost is automaticallycalculated in RSTP operation based on the port link speed.The default costs are :Link Speed Auto Default Cost10Mbps 2000000100Mbps 2000001000Mbps 20000



4.9 802.1X Configuration

-44-


Mode Disabled - disable 802.1X functionEnabled - enable 802.1X function

RADIUS IP IP address of the Radius server

RADIUS UDP Port The UDP port for authentication requests to the specified Radius server

RADIUS Secret The encryption key for use during authentication sessions with the Radiusserver. It must match the key used on the Radius server.

Port Port number

Admin State Port 802.1X controlAuto - set to the Authorized or Unauthorized state in accordance with theoutcome of an authentication exchange between the Supplicant and theAuthentication Server.Force Authorized - the port is forced to be in authorized state.Force Unauthorized - the port is forced to be in unauthorized state.

Port State Port 802.1X state802.1X Disabled - the port is in 802.1X disabled stateLink Down - the port is in link down stateAuthorized (green color) - the port is in 802.1X authorized stateUnauthorized (red color) - the port is in 802.1X unauthorized state

[Re-authenticate] Click to perform a manual authentication for the port.

[Force Reinitialize] Click to perform an 802.1X initialization for the port.

[Statistics] Click to show 802.1X related counters for the port. See Section 4.9.1.

[Re-authenticate All] Click to perform manual authentication for all ports.

[Force Reinitialize All] Click to perform 802.1X initialization for all ports.

[Parameters] Click to configure Re-authentication parameters. See Section 4.9.2.

[Apply] Click to apply the configuration change.

[Refresh] Click to refresh current configuration.

-45-

4.9.1 802.1X Statistics


[Port X] Click to select Port X for the statistics.

[Refresh] Click to refresh current counters.

-46-

4.9.2 802.1X Re-authentication Parameters


Reauthentication Enabled Check to enable periodical re-authentication for all ports

Reauthentication Period The period of time after which the connected radius clients must bere-authenticated (unit: second), Value: 1- 3600

EAP timeout The period of time the switch waits for a supplicant response to anEAP request (unit: second), Value: 1 - 255



-47-

4.10 IGMP Snooping


IGMP Enabled Check to enable IGMP snooping.

Router Ports The ports which have multicast routers connected and requireforwarding of all IPMC packets unconditionally

Unregistered IPMC Flooding Enable to flooding unregistered IPMC

VLAN ID The VID of an existing VLAN

IGMP Snooping Enabled Check to enable IGMP snooping function on the associated VID.

IGMP Querying Enabled Check to enable IGMP querying function on the associated VID.



-48-

4.11 Mirroring


Mirror Port The port is forwarded all packets received on the mirrored ports

Mirror Source Select the ports which will be mirrored all received packets to the mirror port.



-49-

4.12 Quality of Service

QoS Configuration Description

Port Port number

802.1p 802.1p priority classificationEnable - set to enable this classification to the port for priority-tagged andVLAN-tagged packetsDisable - 802.1p classification is not applied to the port

DSCP DSCP classificationEnable - set to enable DSCP classification to the port for IP packetsDisable - DSCP classification is not applied to the port

Port Priority Port default priority class, it is used as a port-based QoS mode when802.1p and DSCP classifications are disabled. It is also used as defaultpriority class for the received packet when both 802.1p and DSCP classifi-cation failed in classification.Class 3 ~ Class 0 - priority class

[802.1p Mapping] Click to configure 802.1p mapping tables.

[DSCP Mapping] Click to configure DSCP mapping table.

[Service Policy] Click to configure per port egress service policy mode.



Note:802.1p classification is superior over DSCP classification if both are enabled. That means if areceived packet is classified successfully in 802.1p classification, the classified priority class isused directly for the packet and the result of DSCP classification is ignored.

-50-

4.12.1 802.1p Mapping


Port n Port number n

tag m 3-bit User priority tag value m ( range : 0 ~ 7 )

Priority class Mapped priority class for tag m on Port nClass 3 ~ Class 0




Every ingress port has its own 802.1p mapping table. The table is referred in 802.1p priority classifica-tion for the received packet.

-51-

4.12.2 DSCP Mapping


DSCP [0-63] Seven user-defined DSCP values which are configured with a priority class0 ~ 63 - 6-bit DSCP value in decimal

Priority The priority class configured for the user-defined DSCP valueClass 3 ~ Class 0

All others The other DSCP values not in the seven user-defined values are assigned adefault priority classClass 3 ~ Class 0




Only one DSCP mapping table is configured and applied to all ports. The table is referred in DSCPpriority classification.

-52-

4.12.3 QoS Service Policy


Port Port number

Policy Service policy for egress priority among four egress class queuesStrict priority - high class queue is served first always till it is emptyWeighted ratio priority Class 3:2:1:0 = 4:3:2:1 - weighted ratio 4:3:2:1Weighted ratio priority Class 3:2:1:0 = 5:3:1:1 - weighted ratio 5:3:1:1Weighted ratio priority Class 3:2:1:0 = 1:1:1:1 - weighted ratio 1:1:1:1




Notes:1. Queue with higher class number has higher priority than queue with lower class number.

That means Class 3 > Class 2 > Class 1 > Class 0 by default.2. In weighted ratio policies, a weighted fairness round robin service is guaranteed normally.

However, when excess bandwidth exists higher class queue will take advantage on band-width allocation.

-53-

4.13 Storm Control


Broadcast Rate The rate limit of the broadcast packets transmitted on a port.

Broadcast Rate The rate limit of the Multicast packets transmitted on a port.

Flooded Unicast Rate The rate limit of the flooded unicast packets transmitted on a port. Theflooded unicast packets are those unicast packets whose destinationaddress is not learned in the MAC address table.



Notes:1. The unit of the rates is pps (packets per second).2. No Limit - no protection control

-54-

4.14 Statistics Overview

Statistics Description

Port Port number

Tx Bytes Total of bytes transmitted on the port

Tx Frames Total of packet frames transmitted on the port

Rx Bytes Total of bytes received on the port

Rx Frames Total of packet frames received on the port

Tx Errors Total of error packet frames transmitted on the port

Rx Errors Total of error packet frames received on the port

[Clear] Click to reset all statistic counters.

[Refresh] Click to refresh all statistic counters.

-55-

4.15 Detailed Statistics

Button Description

[Port #] Click to display the detailed statistics of Port #.

[Clear] Click to reset all statistic counters.

[Refresh] Click to refresh the displayed statistic counters.

-56-

4.16 LACP Status

Status Description


Normal Display the ports not LACP enabled.

Group # The LACP group

Status The LACP port status presented with color and a number<Down> - the port is link down<Blocked & #> - the port is blocked by RSTP and the # is the portnumber of LACP link partner<Learning> - the port is learning by RSTP<Forwarding> - the port is link up and forwarding frames<Forwarding & #> - the port is link up and forwarding frames and the # isthe port number of LACP link partner

Partner MAC address The MAC address of the link partner at the other end of the LACPaggregate

Local Port Aggregated The ports at local end which are aggregated in same LACP group

[Refresh] Click to refresh the status.

Note: the figure shows an example that two LACP link aggregates are configured.

-57-

Status Description


Protocol Active yes - the port is link up and in LACP operationno - the port is link down or not in LACP operation

Partner Port Number The port number of the remote link partner

Operation Port Key The operation key generated by the system

-58-

4.17 RSTP Status

Status Description

VLAN ID The RSTP status on the VLAN is displayed.

Bridge ID The Bridge ID of this Bridge instance.

Hello Time Hello Time is used to determine the periodic time to send normal BPDUfrom designated ports among bridges. It decides how long a bridge shouldsend this message to other bridge to tell I am alive.

Max Age When the switch is the root bridge, the whole LAN will apply this settingas their maximum age time.

Forward Delay This figure is set by Root Bridge only. The forward delay time is defined asthe time spent from Listening state moved to Learning state and also fromLearning state moved to Forwarding state of a port in bridge.

Topology The current state of the Topology Change Flag for this Bridge instance.

Root ID The Bridge ID of the currently elected root bridge.

[Refresh] Click to refresh the status.

-59-

Port Status Description

Port/Group The port ID or aggregation group ID

Vlan ID The RSTP port status on the VLAN is displayed.

Path Cost The current STP port path cost. This will either be a value computed fromthe Auto setting, or any explicitly configured value.

Edge Port The current STP port (operational) Edge Flag. An Edge Port is a switchport to which no Bridges are attached. The flag may be automaticallycomputed or explicitly configured. Each Edge Port transits directly to theForwarding Port State, since there is no possibility of it participating in aloop.

P2P Port The current STP port point-to-point flag. A point-to-point port connects toa non-shared LAN media. The flag may be automatically computed orexplicitly configured. The point-to-point properties of a port affect how fastit can transition STP state.

Protocol STP or RSTP is applied on the port.

Port State The current STP port state. The port state can be one of the followingvalues: Blocking, Learning, Forwarding, Non-STP, Disabled.

-60-

4.18 IGMP Status

Status Description

VLAN ID The IGMP status on the VLAN is displayed.

Querier Show the Querier status is Active or Idle?

Queries transmitted The number of Transmitted Querier

Queries received The number of Received Querier

v1 Reports The number of received v1 reports



v2 Leaves The number of received v2 Leave s

[Refresh] Click to refresh the current status.

VLAN ID The VLAN where the multicast group is found

Groups The IP multicast group found

Port Members The port members of the IP multicast group found

-61-

4.19 Ping

Ping Description

Target IP Address The target IP address to which the ping command issues

Count The number of ping commands generated

Time Out (in secs) The time out for a reply (in seconds)

[Apply] Start the ping command

Status The command status

Received replies The number of replies received by the system

Request time-outs The number of requests time out

Average Response Time The average reponse time of a ping request (in mini-seconds)

-62-

4.20 Reboot System

This menu is used to reboot the switch unit remotely with current configuration. Starting this menu willmake your current http connection lost. You must rebuild the connection to perform any managementoperation to the unit.

4.21 Restore Default

This menu is used to restore all settings of the switch unit with factory default values. Note that thismenu might change the current IP address of the switch and make your current http connection lost.

4.22 Update Firmware

This page facilitates an update of the firmware controlling the switch. Enter the path and file name of asoftware image file for uploading.

[Browse] Click to the location of a software image

[Upload] Click to start uploading.

After the software image is uploaded, a page announces that the firmware update is initiated. Afterabout a minute, the firmware is updated and the switch reboots.

Warning: While the firmware is being updated, Web access appears to be defunct. Do not resetor power off the device at this time or the switch may fail to function afterwards.

-63-

4.23 Configuration File TransferYou can upload or download the switch configuration.

Enter the path and file name of a configuration file for uploading.

[Browse] Click to the location of a configuration file

[Upload] Click to start uploading configuration.

[Download] Click to start download of the configuration.

4.24 Logout

Logout menu is used to perform a logout from the switch management immediately. For convenience,a login page to the same switch is prompted.

-64-

5. SNMP SupportSNMP version support Snmp v1, v2c management

Managed Objects MIB-IIsystem OBJECT IDENTIFIER ::= { mib-2 1 }interfaces OBJECT IDENTIFIER ::= { mib-2 2 }ip OBJECT IDENTIFIER ::= { mib-2 4 }snmp OBJECT IDENTIFIER ::= { mib-2 11 }dot1dBridge OBJECT IDENTIFIER ::= { mib-2 17 }ifMIB OBJECT IDENTIFIER ::= { mib-2 31 }

RFC RFC 3418 - Management Information Base (MIB) for the SimpleNetwork Management Protocol (SNMP)

RFC 1907 - Management Information Base for Version 2 of theSimple Network Management Protocol (SNMPv2)

RFC 1213 - Management Information Base for Network Manage-ment of TCP/IP-based internets:MIB-II

RFC 1158 - Management Information Base for network manage-ment of TCP/IP-based internets: MIB-II

RFC 1493 - Definitions of Managed Objects for Bridges

RFC 2863 - The Interfaces Group MIB

RFC 1573 - Evolution of the Interfaces Group of MIB-II

SNMP Trap Support TRAP_COLDSTART - the device boot up trap

TRAP_LINKUP - the port link recovery trap

TRAP_LINKDOWN - port link down trap

-65-

Appendix. Factory Default SettingsSystem Configuration

DHCP Enabled Not select (disabled)

Fallback IP Address 192.168.0.2

Fallback IP Subnet mask 255.255.255.0

Fallback Gateway IP 192.168.0.1

Management VLAN - VID 0

Management VLAN - CFI 0

Management VLAN - User priority 0

Name Null

Inactiviity timeout 300 seconds

Password 123

SNMP enabled Not select (disabled)

SNMP Trap destination 0.0.0.0

SNMP Read community public

SNMP Write community private

SNMP Trap community public

Ports Configuration

Enable Jumbo Frames Not select (disabled)

Power Saving Mode Full

Port Mode Auto for all ports

Flow Control v : Enable for all ports

VLAN Configuration

Main Mode VLAN Disable

Port-based VLAN Mode setting

Member Ports Port 1, 2, 3, 4, 5, 6 for Group 1None for Group 2

Port-based VLAN ISP Mode setting

Joint Port Port 6

Advanced VLAN Mode Settings

Ingress Default Tag - PVID 1 for all ports

Ingress Default Tag - CFI 0 for all ports

-66-

Ingress Default Tag - User Priority 0 for all ports

Ingress Setting - Tag Aware Tag-ignore for all ports

Ingress Setting - Keep Tag Enable for all ports

Ingress Setting - Drop Untag Disable for all ports

Ingress Setting - Drop Tag Disable for all ports

Egress Setting - Insert Tag Disable for all ports

Egress Setting - Untagging VID Disable for all ports

Egress Setting - Untagged VID 1 for all ports

VLAN Group 1 - VID 1

VLAN Group 1 - Member Ports Port 1, 2, 3, 4, 5, 6

VLAN Group 1 - Source Port Check Disable


VLAN Group 2 - Member Ports None




















LACP Port Configuration

Protocol Enabled Not select (disabled) for all ports

Key Value auto for all ports

-67-

RSTP System Configuration

System Priority 32768

Hello Time 2

Max Age 20

Forward Delay 15

Force Version Normal

RSTP Port Configuration

Protocol enabled Not select (disabled) for all ports

Edge v: Select for all ports

Max Age 20

Forward Delay 15

Force Version Normal

802.1X Configuration

Mode Disabled

RADIUS IP 0.0.0.0

RADIUS UDP Port 1812

RADIUS Secret None

Admin State Force Authorized for all ports

Reauthentication Enabled No

Reauthentication Period 3600

EAP Timeout 30

Port 1~Port 6 - tag 1 Class 0







IGMP Snooping Configuration

IGMP Snooping Enabled for all ports

Router Ports None

Inregistered IPMC Flooding Disabled

IGMP Snooping Enabled for all VLANs

-68-

IGMP Querying Enabled for all VLANs

Mirroring Configuration

Mirror source Not select for all ports

Mirror Port 1 (Port 1)

Quality of Service Configuration

802.1p Classification Disable for all ports

DSCP Classification Disable for all ports

Port Priority Class 3 for all ports

QoS 802.1p Mapping









QoS DSCP Mapping

DSCP 1 / Priority 0, Class 0







All others DSCP Class 0

QoS Service Policy

Port 1 Strict priority






-69-

QoS DSCP Mapping








All others DSCP Class 0

QoS Service Policy







Storm Control Configuration

Broadcast Rate No limit

Multicast Rate No limit

Flooded Unicast Rate No limit

kgs-510f ver.c installation guide · -1-kgs-510f ver.c web smart 6-port gigabit ethernet switch...

Documents