keysight m9341a pxie digital i/o - datatec.de file3 datatec )huglqdqg /dvvdooh 6wu 5hxwolqjhq 7ho...
TRANSCRIPT
Ihr Spezialist fürMess- und Prüfgeräte
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de
Keysight TechnologiesM9341A PXIe Digital I/O
Data Sheet
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de2
02 | Keysight | M9341A PXIe Digital I/O - Data Sheet
Overview
The Keysight M9341A Digital I/O with the 24-bit digital I/O connector and triggering ports provides communication signals between the PXI vector network analyzer (VNA) installed in the same PXI chassis and an external handler.
This allows the PXI VNA such as the Keysight M937xA and M9485A to be used in an automated test environment, where devices to be tested are inserted into a test fixture by a part handler, and sorted into pass/fail bins by the handler after testing is complete. By connecting the part handler to the M9341A digital I/O connector, the VNA and part handler can synchronize their activities in a way that makes automated testing possible. The M9341A digital I/O also compatible with the 24-bit digital I/O connector on the rear panel of the Keysight PNA and ENA Series.
Key specifications/features – Digital I/O for communication for the
PXI VNA with external peripherals
(i.e. handler)
– Synchronized measurements with
the PXI VNA in an automated test
environment
– Compatible with the 24-bit digital I/O
connector on the PNA and ENA
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de3
03 | Keysight | M9341A PXIe Digital I/O - Data Sheet
Specifications
Definitions
Specification (spec.): Warranted performance. All specifications apply at 25 ºC (± 5 ºC), unless otherwise stated, and 45 minutes after the instrument has been turned on. Specifications include guard bands to account for the expected statistical performance distribution, measure-ment uncertainties, and changes in performance due to environmental conditions.
Typical (typ.): Expected performance of an average unit which does not include guardbands. It is not covered by the product warranty.
General characteristics: A general, descriptive term that does not imply a level of performance.
Boundary Conditions:If the same boundary conditions fall under more than one category in a table, apply the best value.
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de4
04 | Keysight | M9341A PXIe Digital I/O - Data Sheet
24 Bit Digital I/O Specification
Description General Characteristics Typical
Connector Type CHAMP 0.8mm, 36 pos Receptacle1
Input Signal LogicInput Voltage RangeHigh-level Input VoltageLow-level Input Voltage
3.3 V TTL-0.5 V to + 5.5 V+2.0 V Min+0.8 V Max
Output Signal LogicHigh-level Output CurrentLow-level Output CurrentOutput Impedance
3.3 V TTL-5 mA+3 mA
100 Ω
Power Supply Output VoltageMaximum Output Current
+4.5 V min, +5.5 V max100 mA
Description General Characteristics Typical
Connector Type SMB
Logic 3.3 V TTL
Description General Characteristics
Size 1 PXIe slot, compatible with PXI hybrid slots
Dimensions 212 mm x 20 mm x 128 mm
Weight (net) 330 g
Power Drawn from Chassis 4.4 W max+3.3 V: 0.73 A+5 V: 0 A+12 V: 0.17 A-12 V: 0 A
Sync Ports Specification
Miscellaneous
1. M9341A-001 provides conversion cable to the 36-pin centronics, female which is compatible with ENA and PNA handler I/F
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de5
05 | Keysight | M9341A PXIe Digital I/O - Data Sheet
General Characteristics
EMC, safety, environment and compliance
Description Specification
EMC
European Council Directive 2014/30/ECIEC 61326-1:2012EN 61326-1:2013CISPR 11:2009 +A1:2010EN 55011: 2009 +A1:2010Group 1, Class AIEC 61000-4-2:2008EN 61000-4-2:20094 kV CD / 8 kV ADIEC 61000-4-3:2006 +A1:2007 +A2:2010EN 61000-4-3:2006 +A1:2008 +A2:20103 V/m, 80-1000 MHz, 1.4 - 2.0 GHz / 1V/m, 2.0 - 2.7 GHz, 80% AMIEC 61000-4-4:2004 +A1:2010EN 61000-4-4:2004 +A1:20102 kV power lines / 0.5 kV signal linesIEC 61000-4-5:2005EN 61000-4-5:20061 kV line-line / 2 kV line-groundIEC 61000-4-6:2008EN 61000-4-6:20093 V, 0.15-80 MHz, 80% AMIEC 61000-4-8:2009EN 61000-4-8:201030A/m, 50/60HzIEC 61000-4-11:2004EN 61000-4-11:20040.5-300 cycle, 0% / 70%
ICES-001:2006 Group 1, Class A
AS/NZS CISPR11:2004Group 1, Class A
KN11, KN61000-6-1 and KN61000-6-2Group 1, Class A
Environment
This product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste.
Product Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed as a “Monitoring and Control instrumentation” product.
Do not dispose in domestic household waste.
To return unwanted products, contact your local Keysight office, or see http://www.keysight.com/environment/product/ for more information.
Ihr Spezialist fürMess- und Prüfgeräte
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de6
06 | Keysight | M9341A PXIe Digital I/O - Data Sheet
General Characteristics continued
Analyzer environmental specifications and dimensions
Operating environment General characteristics
Temperature
Humidity
Altitude
Vibration
0 to 55 °C ambient 0 to 55 °C module temperature
20% to 80% at wet bulb temperature < +29 °C (non-condensation)
0 to 2,000 m (0 to 6561 feet)
0.21 G maximum, 5 Hz to 500 Hz
Non-operating environment General characteristics
Temperature
Humidity
Altitude
Vibration
-40 °C to +70 °C
20% to 90% at wet bulb temperature < +40 °C (non-condensation)
0 to 4,572 m (0 to 15,000 feet)
0.5 G maximum, 5 Hz to 500 Hz
Dimensions
S ync 2
S ync 3
S ync 1
S ync 4
24 Bit Digital I/O
M9341ADigital I/O
Status
19.9
29.3
39.3
49.3
59.3
83.3
4.3
6.3
34.59.7
2.7
130
Änd
erun
gen
und
Irrtü
mer
vor
beha
lten.
dat
aTec
28-
11-2
016
| © K
eysi
ght T
echn
olog
ies:
Nov
embe
r 2, 2
016
| 599
2-18
56E
N
Schnell und bequem online bestellen – bei dataTec ist das möglich. Bei uns finden Sie die perfekte Lö-sung für ihre vielfältigen Anforderungen.
Wir bieten eine unschlagbare Auswahl an Mess- und Prüfgeräten namhafter Hersteller. Diese reicht von Arbiträr-Funktionsgeneratoren über Logikanalysatoren bis hin zu Stromversorgungen und Stromzangen oder Oszilloskopen bis 90 GHz Bandbreite. Hohe Lagerkapazität und kurze Wege sorgen dafür, dass die gewünschte Ware ganz schnell bei Ihnen ist. Bundesweit meist innerhalb eines Tages.
Mehr Klicks, mehr Vorteile: Mehrere tausend Mess- und Prüfgeräte Versandkostenfrei (ab € 80,-) Tagesaktuelle Preise und Promotions Datenblatt-Download Warenkorbrabatt bei Onlinebestellung uvm.
Angebotsanfrage oder Bestellung unter:
STARKE MARKEN. HÖCHSTE PRODUKTVIELFALT. BESTE QUALITÄT.
Ihr Spezialist fürMess- und Prüfgeräte
B2B-ONLINE-
SHOP
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de7
Haben Sie eine technische Frage zu den Geräten, zum Handling und Bedienung eines Gerätes, zur passenden Software und / oder bei der Auswahl des richtigen Equipments für Ihre Messaufgabe?
Bei uns kümmern sich echte Diplom-Ingenieure, Elektronik- und Elektrotechniker mit langjähriger Praxiserfahrung und hoher Kompetenz um Ihr Anliegen. Kostenlos berät Sie unser praxiserfahrener und herstellerzertifizierter Außendienst direkt bei Ihnen vor Ort und / oder führt Ihnen live das ge-wünschte Mess- und Prüfgerät vor.
Die technischen Experten für: Oszilloskope Thermografie / Temperatur Spektrum- / Netzwerkanalysatoren Prüfgeräte VDE / Netzanalyse Netzgeräte / Stromversorgungen uvm.
Technische Frage oder Termin vereinbaren unter:
KOMPETENTE BERATUNG VOR UND NACH DEM KAUF.
UNVERBINDLICHE
BERATUNG
VOR ORT
Ihr Spezialist fürMess- und Prüfgeräte
dataTec Ferdinand-Lassalle-Str. 52 72770 Reutlingen Tel. 07121 / 51 50 50 Fax 07121 / 51 50 10 [email protected] www.datatec.de