k-14715t-1/4/8 parliamentfiles.kohler.com.cn/pdfs/1523261581223_k-14715t-1-4-8_0-sms.pdf · 295mm...
TRANSCRIPT
295mm
50mmFinished Wall
Outline65mm
285mm
485mm
�
�
, 2012
Copyright Kohler China Ltd., 2012
1073822-T01-D
VESSEL/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS
K-14715T-1/4/8PARLIAMENT
ROUGHING-IN
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
( )
( )13mm
Observe all local plumbing and buildingcodes.
Inspect the waste and supply tubing;replace if necessary.
Prior to installation, unpack the newlavatory and carefully inspect it fordamage. Return the lavatory to itsprotective carton until you are ready toinstall it.
For replacement installations, make surethe existing cutout is the same or smallersize as the new lavatory.
Use the template supplied with thelavatory to mark correct size cutout.
Kohler lavatory is made according toAmerican National Standard that it canmatch the American lavatory fittings .Any other lavatory fittings may not fit forkohler lavatory.
Template(supplied)
Safety glasses
Pencil
Scissors
Tape measure
Putty knife
Plumbers putty
Hacksaw
Keyhole saw or saber saw
Drill (13mm or 1/2" dia. drill bit or larger)
Adjustable wrench
Pipe wrench
Tubing cutter
TOOLS AND MATERIALS(Not Supplied)
BEFORE YOU BEGIN
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
13mm
REMOVE EXISTING
LAVATORY
INSTALL NEW
LAVATORY
�
�
Turn off the water supply to the faucet.
Open the faucet valves, then disconnect thesupply lines.
Disconnect the drain assembly and removethe trap.
Remove the existing lavatory.
Cut the template on the cutout line.
Position the template on the countertop toensure clearance between the lavatory,faucet, and backsplash.
Verify cabinet clearance beneath thecountertop.
Trace the template on the countertop with apencil.
Re-check the clearance between thelavatory, faucet, backsplash, and cabinet.Adjust the template accordingly.
Drill a 13mm hole on the inside of thecutout opening.
Cut the opening in the countertop along theinside edge of the pencil line.
Temporaily position the lavatory in theopening, and adjust to fit.
Large lavatories arevery heavy. Get help lifting the lavatoryinto place.
Trace a pencil line around the outside edgeof the lavatory.
Remove the lavatory.
Install the faucet and drain according to themanufacturers instructions.
Apply two beads of sealant to the inside ofthe pencil line.
Spread the sealant evenly with a putty knife.
Carefully position the lavatory in the cutout,and press down firmly.
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
CAUTION: Risk of personal injury or
product damage.
�
�
�
�
�
�
�
CAUTION: Risk of
personal injury or product
damage. Large lavatories
are very heavy. Get help
lifting the lavatory into place.
Immediately wipe away any
excess sealant, and fill any
voids as needed.
Verify that the lavatory has not
moved out of position.
Allow the sealant to cure for at
least 30 minutes before
proceeding.
Connect the faucet supply lines.
Connect the drain assembly.
Open the faucet valves, and
check for leakage.
Clean up with a non-abrasive
cleaner.
�
�
�
�
�
�
�
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
564
75187
35
442
75187
564
3- 35
442
272
102
442
272
564203
3- 3575187
K-14715T-1 K-14715T-4 K-14715T-8
492 492 492
272
95mm 95mm
R20R20
R20
R20
0 Co
IMPORTANTCONSUMERINFORMATION (CAREAND CLEANING)
To keep your lavatory looking new, makesure you rinse it out thoroughly after eachuse. on thisproduct, as they will scratch and ruin thesurface. Stubborn stains, paint, or tar can beremoved with turpentine or paint thinner.
DO NOT USE ABRASIVES
Do not use the product in the water below0 C.
o
CAUTION: Please do not use hardmaterials (like scouring pad) to cleanproduct surface, especially theproduct logo.
Unit: mm:
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value
92
187
Installation Side
92
187
Installation Side
92
187
Installation Side
Length Width Height Depth
Outer562.4 442 186
Inner463 357.9 140