joint oil analysis program manual volume ii...hmws index nbr. hmws page nbr. benzotriazole-1,2,3 37...

(NAVY) NAVAIR 17-15-50.2 (ARMY) TM 38-301-2 (AIR FORCE) T.O. 33-1-37-2 (COAST GUARD) CGTO 33-1-37-2

30 August 2013 Change 1 – 1 June 2015

TECHNICAL MANUAL

JOINT OIL ANALYSIS PROGRAM MANUAL

VOLUME II

SPECTROMETRIC AND PHYSICAL TEST LABORATORY OPERATING REQUIREMENTS

AND PROCEDURES

This manual supersedes NAVAIR 17-15-50.2 dated 31 July 2012.

This manual is incomplete without NAVAIR-17-15-50.1, NAVAIR-17-15-50.3 and

NAVAIR-17-15-50.4

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited, determined on 30 August 2013. Other requests for this document shall be referred to Navy Oil Analysis Program, Naval Air Warfare Center, Aircraft Division, AIR-4.4.6, 22229 Elmer Road, Patuxent River MD 20670-1534 for all volumes.

DESTRUCTION NOTICE - For unclassified, limited documents, destroy by any method that will prevent disclosure of contents or reconstruction of the document.

Published by direction of Commander, Naval Air Systems Command

under the authority of the Joint Oil Analysis Program Regulation AFI 21-131 (I), AR 700-132 and OPNAVINST 4731.1C.

(NAVY) NAVAIR 17-15-50.2 (ARMY) TM 38-301-2 (AIR FORCE) T.O. 33-1-37-2 (COAST GUARD) TO 33-1-37-2

Page A


NUMERICAL INDEX OF EFFECTIVE WORK PACKAGES/PAGES

List of Current Changes

Change # Date Change # Date Original 0 30 Aug 2013 1 1 June 2015

Only those work packages/pages assigned to the manual are listed in this index. Dispose of the superseded issues of the technical manuals. Superseded classified technical information shall be destroyed in accordance with applicable regulations. The portion of text affected in a changed or revised work package is indicated by change bars or the change symbol “R” in the outer margin of each column of text. Changes to illustrations are indicated by pointing hands or change bars, as applicable.

Total number of pages in Volume I of this manual is 408.

Note: the HMWS WP for this manual is located in Volume II

WP Number Title

Total Number of

Pages Change No.

Page A NUMERICAL INDEX OF EFFECTIVE WORK PACKAGES/PAGES A thru C 1

TPDR LIST OF TECHNICAL PUBLICATIONS DISCREPANCY REPORTS INCORPORATED TPDR-1-2 1

HMWS HAZARDOUS MATERIALS WARNINGS 1 thru 50 1

001 00 INTRODUCTION TO VOLUME II INCLUDING MINIMUM REQUIREMENTS AND SPECTROMETER OPERATING PROCEDURES FOR JOAP LABORATORIES

1 thru 24 1

002 00 ARMY OIL ANALYSIS PROGRAM LABORATORIES – OPERATING REQUIREMENTS AND PROCEDURES 1 thru 2 0

002 01 ARMY OAP GENERAL LABORATORY OPERATING PROCEDURES AND OPERATOR TRAINING AND CERTIFICATION REQUIREMENTS 1 thru 4 0

002 02 ARMY OAP LABORATORY EQUIPMENT / CONFIGURATION REQUIREMENTS 1 thru 6 0

002 03 ARMY OAP DATA RECORDING, PROCESSING, AND WAREHOUSING 1 thru 16 0

003 00 NAVY OIL ANALYSIS PROGRAM LABORATORIES OPERATING REQUIREMENTS AND PROCEDURES 1 thru 2 1

003 01 NAVY OAP – GENERAL LABORATORY OPERATING PROCEDURES 1 thru 10 1

003 02 NAVY OAP – LABORATORY EQUIPMENT AND CONFIGURATION REQUIREMENTS 1 thru 4 1

003 03 NAVY OAP - LABORATORY DATA MANAGEMENT SOFTWARE - 1 thru 62 1


Page B


WP Number Title

Total Number of

Pages Change No.

LUBRICANTS ANALYSIS AND RESEARCH APPLICATION (LARA) 003 04 NAVY OAP – LARA TOOLBOX OPERATIONS GUIDE 1 thru 14 1 003 05 NAVY OAP – SHAREPOINT OPERATIONS GUIDE 1 thru 14 1

004 00 AIR FORCE OIL ANALYSIS PROGRAM LABORATORIES OPERATING REQUIREMENTS AND PROCEDURES 1 thru 2 1

004 01 AIR FORCE OAP – GENERAL LABORATORY OPERATING PROCEDURES 1 thru 4 1

004 02 AIR FORCE OAP – LABORATORY EQUIPMENT AND CONFIGURATION REQUIREMENTS 1 thru 2 1

004 03 AIR FORCE OAP - DATA RECORDING, PROCESSING, AND WAREHOUSING 1 thru 2 1

005 00 TOTAL ACID NUMBER (TAN) LABORATORY OPERATING PROCEDURES 1 thru 4 1

006 00 BROOKFIELD SCANNING VISCOMETER LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 12 0

007 00 CAMBRIDGE VISCOMETER LABORATORY PROCEDURES 1 thru 6 1 008 00 CRACKLE TEST LABORATORY PROCEDURES 1 thru 2 0

009 00 AQUATEST 2010 (KARL FISCHER WATER TEST) LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 14 1

010 00 AQUATEST VIII LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 8 0

011 00 PALL WATER TEST LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 2 0

012 00 BLOTTER (SPOT) TEST LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 2 0

013 00 FERROGRAPHY LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 12 0

014 00 FOURIER TRANSFORM INFRA-RED (FT-IR) LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 6 0

015 00 SETAFLASH LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 4 0

016 00 FUEL DILUTION METER LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 6 1

017 00 MICROSCOPIC ANALYSIS LABORATORY PROCEDURES AND REQUIREMENTS 1 thru 2 0

018 00 PODS PARTICLE COUNTER PROCEDURE 1 thru 2 1 019 00 USAF B-2 COOLANT TEST 1 thru 20 0 020 00 CONTAMINATION TESTING OF COOLANT 1 thru 16 0 021 00 FLUID CONTAMINATION 1 thru 6 0 022 00 VISCOSITY BY ANTON PARR 1 thru 2 1


Page C


WP Number Title

Total Number of

Pages Change No.

023 00 TYPE EQUIPMENT CODES 1 thru 56 1 024 00 MAJOR COMMAND CODES 1 thru 2 1


TPDR-1


NAVAL AIR SYSTEMS COMMAND TECHNICAL MANUAL PROGRAM

LIST OF TECHNICAL PUBLICATIONS DEFICIENCY REPORTS INCORPORATED

1. The TPDRs listed below have been incorporated in this issue.

Activity Report Control Number Location

JOAP Executive Committee N00421-15-1140 WP HMWS JOAP Executive Committee N00421-15-1141 WP 001 00 Navy Oil Analysis Program Team N00421-15-1142 WP 003 00 Navy Oil Analysis Program Team N00421-15-1143 WP 003 01 Navy Oil Analysis Program Team N00421-15-1144 WP 003 02 Navy Oil Analysis Program Team N00421-15-1145 WP 003 03 Navy Oil Analysis Program Team N00421-15-1146 WP 003 04 AF Oil Analysis Program Team N00421-15-1147 WP 004 00 AF Oil Analysis Program Team N00421-15-1148 WP 004 01 AF Oil Analysis Program Team N00421-15-1149 WP 004 02 AF Oil Analysis Program Team N00421-15-1150 WP 004 03 Navy Oil Analysis Program Team N00421-15-1151 WP 005 00 Navy Oil Analysis Program Team N00421-15-1152 WP 007 00 Navy Oil Analysis Program Team N00421-15-1153 WP 016 00 Navy Oil Analysis Program Team N00421-15-1154 WP 018 00 Navy Oil Analysis Program Team N00421-15-1155 WP 022 00 JOAP Executive Committee N00421-15-1156 WP 023 00 JOAP Executive Committee N00421-15-1157 WP 024 00


TPDR-2


This Page Intentionally Left Blank

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2

WP HMWS Page 1 of 50

Change 1 - 1 June 2015

WARNINGS APPLICABLE TO HAZARDOUS MATERIALS

Warnings in this manual alert personnel to hazards associated with the use of hazardous materials. Additional information related to hazardous materials is provided in OPNAVINST 5100.23, Navy Hazardous Material Control Program, and the DOD 6050.5, Hazardous Materials Information System (HMIS) series publications. For each hazardous material used within the Navy, a Material Safety Data Sheet (MSDS) must be provided and available for review by users. Consult your local safety and health staff concerning any questions regarding hazardous materials, MSDS, personnel protective equipment requirements, appropriate handling and emergency procedures, and disposal guidance. Under the heading “HAZARDOUS MATERIALS WARNINGS”, complete warnings, including related icon(s) and numeric identifier, are provided for hazardous materials used in this manual. In the text of the manual, the caption “WARNING” is not used for hazardous material warnings. Hazards are cited with appropriate icon(s), the nomenclature of the hazardous material, and the numeric identifier that relates to the complete warnings. Users of hazardous materials shall refer to the complete warnings.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2



NAME HMWS Index Nbr. HMWS Page

Nbr. Tricresyl Phosphate 1 4 MIL-PRF-680 (Degreasing Solvent) 2 5 SAE-J1899 (lube Oil) 3 6 SAE-J1966 (Lube Oil) 4 7 MIL-PRF-2104 (Lube Oil) 5 7 MIL-PRF-2105 (Lube Oil) 6 8 SAE-J2360 (Lube Oil) 7 8 MIL-PRF-5606 8 9 MIL-PRF-6081 (Lube Oil) 9 9 MIL-L-6082 10 10 MIL-PRF-6083 11 10 MIL-PRF-7808 12 11 MIL-PRF-8188 13 11 MIL-PRF-83282 14 12 MIL-PRF-9000 15 12 MS-9250 16 13 MIL-L-15019 17 13 MIL-DTL-17111 18 14 MIL-PRF-17331 19 14 MIL-PRF-17672 20 15 MIL-H-19457 21 15 MIL-PRF-21260 22 16 HIL-H-22072 23 16 MIL-L-22851 24 17 MIL-PRF-23699 25 18 MIL-L-27502 26 18 MIL-PRF-46170 (Hyd. Fluid) 27 19 DOD-PRF-85734 28 19 MIL-PRF-87257 29 20 Skydrol Hydraulic Fluid 30 20 Philips 66 Reference Oil 50 31 21 Alcohol, Isopropyl 32 22 BioXcel 33 22 1-Bromonaphthalene 96% 34 23 2(3H)-Benzothiazolethione, Sodium Salt (Liquid), 35 24 Acetic Acid, 96%, 36 25

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2



NAME HMWS Index Nbr. HMWS Page

Nbr. Benzotriazole-1,2,3 37 26 BIO-TEK 134 HI-SOLV (Solvent) 38 27 Chevron FLO-COOL 180 39 27 COOLANOL 25R 40 28 Diesel Fuel NO. 2 41 29 Electron (ECOLINK ) 42 30 Ethylene Glycol 43 31 Gasoline 44 32 Heptane 45 33 Hexane 46 34 MIL-DTL-5624, JP-5 Jet Fuel 47 35 MIL-DTL-83133, JP-8 Jet Fuel 48 36 Methanol (Methyl alcohol) 49 37 Nitric Acid (65% - 70%) 50 37 Petroleum Ether 51 38 pH 4 Buffer 52 39 pH 7.00 Buffer 53 39 Phosphoric Acid 85% 54 39 PhotoVolt Aquatest 2% Water Standard 55 40 PhotoVolt Aquatest Generator Solution 56 41 PhotoVolt Aquatest Vessel Solution 57 42 p-Naphtholbenzein 58 43 Potassium Hydroxide 0.1N Solution in Methanol 59 44 S60S Viscometer Calibration Standard 60 45 Silicone (Liquid) 61 45 Sodium Hydroxide 0.1N 62 46 Toluene 63 47 Viscometer Calibration Standard Petroleum - Cannon 64 48 Viscometer Calibration Standard Synthetic - Cannon 65 48 MIL-DTL-85694 Spectrometric Oil Standards 66 49

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2



HAZARDOUS MATERIALS WARNINGS

INDEX MATERIAL WARNING

1

Specification TT-T-656,

Tricresyl Phosphate

TT-T-656, FEDERAL SPECIFICATION: TRICRESYL PHOSPHATE. This specification covers tricresyl phosphate, a reaction product of cresylic acid and a phosphorus compound. Cresylic acid derived from petroleum or coal tar is acceptable. Overview and First Aid: Tricresyl Phosphate is a POISON material. It is also a skin, eye, digestive and respiratory tract irritant. May cause irritation of the digestive tract. May cause headache. May cause muscle paralysis, respiratory failure, and possible death. Toxic if swallowed. Overexposure to this product by ingestion, inhalation, or skin absorption may cause cholinesterase inhibition. Symptoms of cholinesterase inhibition may include: headache, nausea, sweating, numbness and tingling of the hands and feet, salivation, muscle twitching, tremors, incoordination, blurred vision, tears, abdominal cramps, diarrhea, and chest discomfort. Avoid contact with skin and eyes. Wash hands thoroughly after each use. Launder contaminated clothing before reuse. If swallowed, get medical aid immediately. Only induce vomiting if directed to do so by medical personnel. Never give anything by mouth to an unconscious person. If inhaled, get medical aid immediately. Remove victim to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Protection: Wear chemical goggles and rubber gloves; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas, especially when misting occurs. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical aid. Do not breathe dust, mist, or vapor. Do not get in eyes, on skin, or on clothing. Keep container tightly closed. Do not ingest or inhale. Use only in a chemical fume hood. Storage: Store in a cool, dry place, away from heat, flames, and oxidizing agents.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2


Change 1 1 June 2015

HAZARDOUS MATERIALS WARNINGS (CONTINUED)


2

MIL-PRF-680, Degreasing Solvent

MIL-PRF-680, PERFORMANCE SPECIFICATION: DEGREASING SOLVENT. This specification covers degreasing solvent that consists of four types of petroleum distillates. The different types are referred to as "Stoddard solvent", "141 degrees Fahrenheit (degrees F) (60.6 degrees Celsius (degrees C)) solvent", "200 degrees F (93.3 degrees C) solvent", and "141 degrees F d-limonene blended solvent". They are used for degreasing of machine parts in equipment maintenance. MIL-PRF-680, degreasing solvent is not classified as dangerous. Good general ventilation should be sufficient to control worker exposure to airborne contaminants. If this product contains ingredients with exposure limits, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure below any recommended or statutory limits. Hygiene Measures: Wash hands, forearms and face thoroughly after handling compounds and before eating, smoking and using the lavatory and at the end of the day. During formulation, follow good industrial hygiene practice. Eye and Hand Protection: Safety glasses with side shields. Natural rubber (latex) gloves. . In case of contact with eyes, rinse immediately with plenty of water. Check for and remove any contact lenses Obtain medical attention if symptoms occur. If ingested do not induce vomiting. Never give anything by mouth to an unconscious person. Get medical attention if symptoms appear. If inhaled, remove to fresh air. If not breathing, give artificial respiration. Get medical attention if symptoms appear. Wash with soap and water. Obtain medical attention if symptoms occur.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





3

SAE-J1899, Lubricating Oil

OIL, LUBRICATING, AIRCRAFT PISTON ENGINE (ASHLESS DISPERSANT) SAE-J1899, ADOPTION NOTICE; OIL, LUBRICATING AIRCRAFT PISTON ENGINE (ASHLESS DISPERSANT). This SAE Standard establishes the requirements for lubricating oils containing ashless dispersant additives to be used in four-stroke cycle, reciprocating piston aircraft engines. This document covers the same lubricating oil requirements as the former military specification MIL-L-22851. Users should consult their airframe or engine manufacturer’s manuals for the latest listing of acceptable lubricants. SAE-J1899 Grades: W65 W80 W100 W120 Lubricating oil, SAE-J1899, is a skin, eye, and respiratory tract irritant. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Avoid contact with skin and eyes. Wash hands thoroughly after each use. Launder contaminated clothing before reuse. If ingested do not induce vomiting. Never give anything by mouth to an unconscious person. Get medical attention if symptoms appear. Store in a cool, dry place, away from heat, flames, and oxidizing agents. Protection: Wear chemical goggles and rubber gloves; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





4

SAE-J1966, Lubricating Oil,

Aircraft Piston Engine, Mineral Oil,

Refer to MIL-PRF-6082

SAE-J1966, ADOPTION NOTICE; OILS, LUBRICATING, AIRCRAFT PISTON ENGINE (NONDISPERSANT MINERAL OIL). SAE-J1966, "Lubricating Oils, Aircraft Piston Engine (Nondispersant Mineral Oil)", was adopted on 01-NOV-95 for use by the Department of Defense (DoD). This SAE Standard establishes the requirements for nondispersant, mineral lubricating oils to be used in four-stroke cycle piston aircraft engines. This document covers the same lubricating oil requirements as the former military specification MIL-L-6082. Users should consult their airframe or engine manufacturer’s manuals for the latest listing of acceptable lubricants. Aircraft lubricating oil, SAE-J1966, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

5

MIL-PRF-2104 Lubricating Oil,

Internal Combustion Engine,

MIL-PRF-2104, PERFORMANCE SPECIFICATION: LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT/TACTICAL SERVICE. This performance specification covers engine oils suitable for lubrication of reciprocating compression-ignition internal combustion engines and for power transmission fluid applications in combat/tactical service equipment. Aircraft lubricating oil, MIL-PRF-2104, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





6

MIL-PRF-2105, Lubricating Oil,

Gear Multipurpose

Refer to SAE-J2360

MIL-PRF-2105, PERFORMANCE SPECIFICATION: LUBRICATING OIL, GEAR, MULTIPURPOSE [S/S BY SAE-J2360]. Aircraft lubricating oil, SAE-J2360, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

7

SAE-J2360

Lubricating Oil

This SAE Standard covers multipurpose gear lubricating military oils. This standard is equivalent to MIL-PRF-2105 when all requirements are met. API Category GL-5 designates the type of service characteristic of gears, particularly hypoids in automotive axles under high-speed and/or low-speed, high-torque conditions. SAE-J2360 grades: 75W 80W-90 85W-140 Aircraft lubricating oil, SAE-J2360, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





8

MIL-PRF-5606, Hydraulic Fluid,

Aircraft, Missile and Ordinance,

Petroleum Base,

MIL-PRF-5606, PERFORMANCE SPECIFICATION: HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE., This specification describes the characteristics and provides the requirements for a petroleum base hydraulic fluid for use in the -54 Deg. C to +135 Deg. C temperature range. This fluid is identified by military symbol OHA and NATO Code No. H-515. Hydraulic fluid, MIL-PRF-5606, is flammable, toxic and an irritant. Keep away from heat, sparks, open flames and static electricity. Use in well-ventilated area, especially when exposure to hot oil or oil mist is possible. Eye contact: Flush with water for 15 minutes; get medical attention. Skin contact: Wash with soap and water. Ingestion: Do not induce vomiting; get medical attention. Wash hands with soap and water after use and before eating, drinking or smoking. If Swallowed: drink plenty of water, DO NOT induce vomiting. Immediately call a doctor.

9


Jet Engine, Petroleum Base

MIL-PRF-6081, PERFORMANCE SPECIFICATION: LUBRICATING OIL, JET ENGINE., This specification covers the requirements for two grades of jet engine lubricating oil, grades 1010 and 1005. Lubricating oil, MIL-PRF-6081 Grade 1010, is a skin, eye, and respiratory tract irritant. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Avoid contact with skin and eyes. Use with adequate ventilation. Avoid breathing vapor. If heated and ventilation is inadequate, use NIOSH certified respirator, which will protect against organic vapor. Safety glasses, chemical goggles, or face shields recommended to prevent contact. Wear clothing and gloves that cannot be penetrated by chemicals or oil. Wash hands thoroughly after each use. Launder contaminated clothing before reuse. Store in a cool, dry place, away from heat, flames, and oxidizing agents. Protection: Wear chemical goggles and rubber gloves; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





10

MIL-L-6082, Lubricating Oil,

Aircraft Piston Engine, Mineral Oil,

Refer to SAE-J1966

MIL-L-6082, MILITARY SPECIFICATION: LUBRICATING OIL, AIRCRAFT PISTON ENGINE (NON-DISPERSANT MINERAL OIL) [S/S BY SAE-J1966]. Aircraft lubricating oil, MIL-L-6082, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

11

MIL-PRF-6083, Hydraulic Fluid, Petroleum Base,

MIL-PRF-6083, PERFORMANCE SPECIFICATION: HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION., This specification describes the characteristics and provides the requirements for one grade of petroleum base hydraulic fluid for use in the -54 DEG C to +135 DEG C temperature range (see 6.1). This fluid is rust inhibited and used both as a preservative for hydraulic systems and components as well as being an operational fluid. This hydraulic fluid will not be used for aircraft systems, aircraft ground support equipment, or the preservation of aircraft components. The hydraulic fluid is identified by Military Symbol OHT and NATO Symbol C-635. Hydraulic fluid, MIL-H-6083, is flammable, toxic and an irritant. Keep away from heat, sparks, open flames and static electricity. Use in well-ventilated area, especially when exposure to hot oil or oil mist is possible. Eye contact: Flush with water for 15 minutes; get medical attention. Skin contact: Wash with soap and water. Ingestion: Do not induce vomiting; get medical attention. Wash hands with soap and water after use and before eating, drinking or smoking.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





12


Aircraft Turbine Engine, Synthetic Base,

MIL-PRF-7808, PERFORMANCE SPECIFICATION; LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE., This specification covers the requirements for two grades of aircraft turbine engine lubricating oil, grade 3 and 4. Aircraft lubricating oil, MIL-PRF-7808, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

13


Aircraft Turbine Engine, Synthetic Base

MIL-PRF-8188, PERFORMANCE SPECIFICATION: CORROSION-PREVENTIVE, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE., This specification covers the requirements for one type of corrosion-preventive oil for preservation of engines which normally operate on synthetic base oils. This oil is identified by NATO Code Number C-638. Aircraft lubricating oil, MIL-PRF-8188, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





14

MIL-PRF-83282, Hydraulic Fluid, Fire Resistant

MIL-PRF-83282, PERFORMANCE SPECIFICATION: HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, NATO CODE NUMBER H-537., This specification covers the requirements for a synthetic hydrocarbon-base hydraulic fluid for use in the temperature range of -40 deg to +205 deg C. This hydraulic fluid is identified by NATO Code Number H-537. Hydraulic fluid, MIL-PRF-83282, is a skin, eye, and respiratory tract irritant. May contain small quantities of tricresyl-phosphate, a toxic substance. There is a slight fire/explosive hazard when fluid is exposed to heat and flames. Use in well ventilated area. Keep container tightly closed when not in use. Keep away from heat sparks, open flames, and oxidizing agents. Avoid contact with clothing, eyes and skin. Wash hands thoroughly with soap and water after use. Protection: Wear chemical goggles, butyl gloves, and face shield; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

15


Shipboard Combustion Engine

MIL-PRF-9000, PERFORMANCE SPECIFICATION: LUBRICATING OIL, SHIPBOARD INTERNAL COMBUSTION ENGINE, HIGH OUTPUT DIESEL ., This specification covers two grades (SAE 40 and SAE 15W40) of lubricating oil for use in advanced design high-output shipboard main propulsion and auxiliary diesel engines using fuel conforming to MIL-DTL-16884 and MIL-DTL-5624. Military Symbol 9250, NATO Code 0-278 is the designation used for the SAE 40 Grade product. There is not a Military Symbol or NATO designation for the 15W40 Grade product. Aircraft lubricating oil, MIL-PRF-9000, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





16

MS-9250, Lubricating Oil,

Refer to MIL-PRF-9000

MILITARY SYMBOL, MS-9250 is identified as MIL-PRF-9000 (NAVSEA) and NATO Code 0-278. Aircraft lubricating oil, MS-9250, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

17


Marine Engine Oil,

MIL-L-15019, Lubricating Oil, Compounded - Symbols 4065 & 6135, Marine Engine Oils, can be used as marine stern tube lubricants where oils complying with MIL-L-15019 Symbols 4065 an 6135 are required. MIL-L-15019 specifies emulsifying type lubricants are formulated using a blend of high grade, medium viscosity index base oils and carefully balanced additive package to meet the crankcase need of marine steam engines. Aircraft lubricating oil, MIL-L-15019, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





18

MIL-DTL-17111, Transmission Fluid,

MIL-DTL-17111, DETAIL SPECIFICATION: FLUID, POWER TRANSMISSION. This specification covers a class of fluid for use in the hydraulic transmission of power. This fluid is identified by NATO Code No. H-575. Transmission fluid, MIL-DTL-17111, is a skin, eye, and respiratory tract irritant. May contain small quantities of tricresyl-phosphate, a toxic substance. There is a slight fire/explosive hazard when fluid is exposed to heat and flames. Use in well ventilated area. Keep container tightly closed when not in use. Keep away from heat sparks, open flames, and oxidizing agents. Avoid contact with clothing, eyes and skin. Wash hands thoroughly with soap and water after use. Protection: Wear chemical goggles, butyl gloves, and face shield; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

19


Petroleum Base, Steam Turbine,

1

MIL-PRF-17331, PERFORMANCE SPECIFICATION: LUBRICATING OIL, STEAM TURBINE AND GEAR, MODERATE SERVICE ., This specification covers a single classification of steam turbine and gear lubricating oil, moderate service, for use in main and auxiliary turbines and gears, air compressors, and certain hydraulic equipment, as well as for general mechanical lubrication. The lubricating oil will be identified as follows: Military symbol 2190 TEP NATO symbol O-250. Aircraft lubricating oil, MIL-PRF-17331, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





20

MIL-PRF-17672, Hydraulic Fluid, Petroleum Base,

MIL-PRF-17672, PERFORMANCE SPECIFICATION: HYDRAULIC FLUID, PETROLEUM, INHIBITED. Symbols 2075TH, 2110TH & 2135TH. This specification covers petroleum base hydraulic fluids for use in hydraulic systems and in other applications where a high grade hydraulic fluid having anti-corrosion and anti-oxidation properties are required. This hydraulic fluid is not an extreme pressure (EP) or anti-wear (AW) fluid. This hydraulic fluid should not be used in systems where a fire-resistant fluid is required. Hydraulic fluid, MIL-PRF-17672, is flammable, toxic and an irritant. Keep away from heat, sparks, open flames and static electricity. Use in well-ventilated area, especially when exposure to hot oil or oil mist is possible. Eye contact: Flush with water for 15 minutes; get medical attention. Skin contact: Wash with soap and water. Ingestion: Do not induce vomiting; get medical attention. Wash hands with soap and water after use and before eating, drinking or smoking.

21

MIL-H-19457, Hydraulic Fluid, Fire Resistant,

MIL-H-19457, MILITARY SPECIFICATION: HYDRAULIC FLUID, FIRE-RESISTANT, NON-NEUROTOXIC., This specification covers the requirements of fire-resistant hydraulic fluid for hydraulic systems which are accumulator loaded and operate above 600 pounds per square inch gauge. Hydraulic fluid, MIL-PRF-19457, is a skin, eye, and respiratory tract irritant. May contain small quantities of tricresyl-phosphate, a toxic substance. There is a slight fire/explosive hazard when fluid is exposed to heat and flames. Use in well ventilated area. Keep container tightly closed when not in use. Keep away from heat sparks, open flames, and oxidizing agents. Avoid contact with clothing, eyes and skin. Wash hands thoroughly with soap and water after use. Protection: Wear chemical goggles, butyl gloves, and face shield; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





22


Internal Combustion,

MIL-PRF-21260, PERFORMANCE SPECIFICATION: LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATIVE BREAK-IN. This performance specification covers engine oils suitable for preservation, break-in, and lubrication of reciprocating internal combustion engines of both spark-ignition and compression-ignition types, and of power transmission fluid applications in equipment used in combat/tactical service. Aircraft lubricating oil, MIL-PRF-21260, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

23

MIL-H-22072 Hydraulic Fluid,

Catapult,

MIL-H-22072, MILITARY SPECIFICATION: HYDRAULIC FLUID, CATAPULT, NATO CODE NUMBER H-579 . MIL-H-22072 has been reviewed and determined to be valid for use in acquisition. Hydraulic fluid, MIL-H-22072, is flammable, toxic and an irritant. Keep away from heat, sparks, open flames and static electricity. Use in well-ventilated area, especially when exposure to hot oil or oil mist is possible. Eye contact: Flush with water for 15 minutes; get medical attention. Skin contact: Wash with soap and water. Ingestion: Do not induce vomiting; get medical attention. Wash hands with soap and water after use and before eating, drinking or smoking.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





24


Aircraft Piston Engine,

MIL-L-22851, MILITARY SPECIFICATION: LUBRICATING OIL, AIRCRAFT PISTON ENGINE (ASHLESS DISPERSENT) [S/S BY SAE-J1899]. This SAE Standard establishes the requirements for lubricating oils containing ashless dispersant additives. SAE-J1899 Grades: W65 W80 W100 W120 Aircraft lubricating oil, MIL-L-22851, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





25



MIL-PRF-23699, MILITARY STANDARD, LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE, NATO CODE NUMBER O-156., This specification covers three classes of gas turbine engine lubricating oils, primarily used for aircraft engines, which have a nominal viscosity of 5 centistokes at 100 Deg. C and which are typically made with neopentyl polyol ester base stocks. Aircraft lubricating oil, MIL-PRF-23699, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full- face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

26



MIL-L-27502, MILITARY STANDARD, LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, ESTER BASE., This specification covers the requirements for one grade of aircraft gas turbine engine lubricating oil. Aircraft lubricating oil, MIL-L-27502, is toxic, and a skin, eye, and respiratory tract irritant. If lubricating oil is decomposed by heat, toxic gases are released. Keep away from open flame, sparks, or heat. Use in a well ventilated area, especially when exposure to hot oil or mist is possible. Wash hands thoroughly after use. Launder contaminated clothing before re-use; discard contaminated boots or shoes if oil soaked. Keep containers closed when not in use. Avoid strong oxidizing agents. Protection: Wear chemical goggles, rubber gloves, and protective clothing; full-face piece continuous supplied air respirator required in poorly ventilated areas, especially when misting occurs. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water; remove contaminated clothing and shoes. If ingested, do not induce vomiting, seek medical attention. If inhalation occurs, remove from area to fresh air.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





27

MIL-PRF-46170, Hydraulic Fluid, Fire Resistant, Synthetic Base

MIL-PRF-46170, PERFORMANCE SPECIFICATION: HYDRAULIC FLUID, RUST INHIBITED, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, NATO CODE NO. H-544, This specification covers the requirements for one type of synthetic hydrocarbon base hydraulic fluid. Hydraulic fluid, MIL-PRF-46170, is a skin, eye, and respiratory tract irritant. May contain small quantities of tricresyl-phosphate, a toxic substance. There is a slight fire/explosive hazard when fluid is exposed to heat and flames. Use in well ventilated area. Keep container tightly closed when not in use. Keep away from heat sparks, open flames, and oxidizing agents. Avoid contact with clothing, eyes and skin. Wash hands thoroughly with soap and water after use. Protection: Wear chemical goggles, butyl gloves, and face shield; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

28

DOD-PRF-85734, Lubricating Oil,

Helicopter Transmission System,

Synthetic Base,

DOD-PRF-85734, PERFORMANCE SPECIFICATION: LUBRICATING OIL, HELICOPTER TRANSMISSION SYSTEM, SYNTHETIC BASE., This specification covers the requirements for one grade of a synthetic base helicopter transmission system lubricating oil.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





29

MIL-PRF-87257, Hydraulic Fluid, Fire Resistant, Synthetic Base,

MIL-PRF-87257, PERFORMANCE SPECIFICATION: HYDRAULIC FLUID, FIRE RESISTANT; LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE. This specification describes the characteristics and provides the requirements for a synthetic hydrocarbon base hydraulic fluid for use in the -54 degrees C to +200 degrees C temperature range in aircraft and missile hydraulic systems. This hydraulic fluid is identified by NATO Code No. H-538. Hydraulic fluid, MIL-PRF-87257, is a skin, eye, and respiratory tract irritant. May contain small quantities of tricresyl-phosphate, a toxic substance. There is a slight fire/explosive hazard when fluid is exposed to heat and flames. Use in well ventilated area. Keep container tightly closed when not in use. Keep away from heat sparks, open flames, and oxidizing agents. Avoid contact with clothing, eyes and skin. Wash hands thoroughly with soap and water after use. Protection: Wear chemical goggles, butyl gloves, and face shield; half-mask respirator with organic vapor cartridge may be required in poorly ventilated areas. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If inhalation occurs, remove from area to fresh air.

30

Skydrol® Hydraulic Fluid

Skydrol® Hydraulic fluid is an odorless, oily liquid, clear to purple in color. It is flammable, toxic and an irritant. Keep away from heat, sparks, open flames and static electricity. Use in well-ventilated area, especially when exposure to hot oil or oil mist is possible. Eye contact: Immediately flush with plenty of water; get medical attention if irritation persists. Skin contact: Immediately flush with plenty of water. Remove contaminated clothing. Wash skin gently with soap as soon as available. Get medical attention if irritation persists. Wash contaminated clothing before re-use. Ingestion: Immediate first aid is not likely required. Get medical attention if irritation persists. Wash hands with soap and water after use and before eating, drinking or smoking.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





31

Philips 66 Reference Oil 50,

Lubricating Oil, Base Oil (Petroleum),

Reference Oil 50 is an eye and skin irritant. No harmful effects are expected from swallowing. Studies by other exposure route suggest a low degree of toxicity by inhalation. Effects of overexposure may include irritation of the digestive tract, nausea or diarrhea. Inhalation of oil mist or vapors at elevated temperatures may cause respiratory irritation. If eye irritation or redness develops, move the victim away from the exposure and into fresh air. Flush eyes with clean water. If symptoms persist seek medical attention. Wipe material from skin and remove contaminated shoes and clothing. Cleanse affected area(s) thoroughly by washing with mild soap and water and if necessary, a waterless skin cleanser. If irritation or redness develops persists, seek medical attention. If respiratory symptoms develop, move victim away from source of exposure and into fresh air. If symptoms persist, seek medical attention. If victim is not breathing, clear airway and immediately begin artificial respiration. If breathing difficulties develop, oxygen should be administered by qualified personnel. Seek immediate medical attention. Fire Protection: This material my burn, but will not ignite readily. If container is not properly cooled, it can rupture in the heat of a fire. Vapors are heavier tan air and can accumulate in low areas. Handling and Storage: The use of appropriate respiratory protection is advised when concentrations exceed any established exposure limits (refer to MSDS). Do not wear contaminated clothing or shoes. “Empty” containers retain residue and may be dangerous. Use and store this material in cool, dry, well-ventilated areas away from heat and all sources of ignition. Store only in approved containers. Personal Protection: A respiratory protection program that meets OSHA’s 29 CFR 1910.134 and ANSI Z88.2 requirements must be followed whenever workplace conditions warrant a respirator’s use. The use of gloves impervious to the specific material handled is advised to prevent skin contact and possible irritation. Approved eye protection to safeguard against potential eye contact, irritation or injury is recommended. Depending on conditions of use, a face shield may be necessary. The oil is stable under normal ambient and anticipated storage and handling conditions of temperature and pressure. Extended exposure to high temperatures can cause decomposition. Avoid contact with strong oxidizing agents.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





32

Alcohol, Isopropyl TT-I-735

Isopropyl alcohol, TT-I-735, is toxic, flammable, and a skin and respiratory tract irritant. It may be fatal if swallowed. DO NOT use near open flame, sparks or heat. DO NOT use synthetic cloths for wiping with this solvent. DO NOT smoke, eat or drink when using solvent. Avoid breathing vapor. Use only in well ventilated areas. Metal containers containing solvent shall be grounded to prevent sparking and fires. Avoid prolonged breathing of vapor and skin contact, which can cause dermatitis, irritated nose and throat, and dizziness. Protection: Wear butyl gloves and chemical goggles; faceshield and protective clothing required when splashing is possible or expected; half-mask respirator with organic vapor cartridge required in poorly ventilated areas. If eye contact occurs, flush immediately with large amounts of water for 15 minutes and seek medical attention. If skin contact occurs, wash with soap and water, remove contaminated clothing and shoes. If ingested, give water to drink and seek medical attention. Do not induce vomiting. If inhalation occurs, remove from area to fresh air.

33 BioForce

BioForce is an eye and skin irritant. Protection: Chemical splash proof goggles, and rubber or plastic gloves. Insure good personal hygiene prior to eating, drinking, or smoking.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





34

1-Bromonaphthalene 96% contains max. 2%

2-bromonapthalene, AF Coolant Contam. Test

1-Bromonaphthalene is harmful if swallowed. May cause eye, skin and respiratory tract irritation. Target organs: Blood and eyes. Eyes: May cause eye irritation, Naphthalene is an eye irritant and the vapor causes eye irritation at 15 PPM. Eye contact with the solid material may result in conjunctivitis, superficial injury to the cornea, diminished visual acuity and other effects. It may cause cataracts. Skin: May cause skin irritation. May be harmful if absorbed through the skin. The toxicological properties of this material have not been fully investigated. Ingestion: Harmful if swallowed. May cause gastrointestinal irritation with nausea, vomiting and diarrhea. The toxicological properties of this substance have not been fully investigated. Inhalation: May cause respiratory tract irritation. The toxicological properties of this substance have not been fully investigated. May be harmful if inhaled. Chronic: Chronic inhalation, skin absorption or ingestion of naphthalene have caused severe hemolytic anemia. First Aid Measures. Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical aid. Skin: Get medical aid. Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Ingestion: Get medical aid. DO NOT induce vomiting. If conscious and alert, rinse mouth and drink 2-4 cupfuls of milk or water. Inhalation: Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid if cough or other symptoms appear.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





35

2(3H)-Benzothiazolethione, Sodium Salt (Liquid),

AF Coolant Contam. Test

2(3H)-Benzothiazolethione, sodium salt causes eye and skin burns and may cause allergic skin reactions. Do not get in eyes or on skin or clothing. Avoid breathing vapor or mist. Keep container closed. Use only with adequate ventilation. Wash thoroughly after handling. Routes of entry: Dermal contact. Eye contact. Inhalation. Ingestion. Eye contact: Check for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical attention immediately. Skin contact: In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention immediately. Inhalation: Move exposed person to fresh air. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention immediately. Ingestion: Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical attention immediately. Notes to physician: In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. Medical conditions aggravated by overexposure: Pre-existing skin disorders may be aggravated by over-exposure to this product. Handling and Storage: Wash hands and face before eating, drinking and smoking. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not ingest. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Keep away from acids. Empty containers retain product residue and can be hazardous. Do not reuse container. Oxidizes if exposed to air for prolonged periods, resulting in the precipitation of solids. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area. Separate from acids. Personal Protection: Use a properly fitted, air-purifying or air-fed respirator. Chemical-resistant, impervious gloves complying with an approved standard should be worn. Safety eyewear should be used.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





36

Acetic Acid, 96%, AF Coolant Contam. Test

Acetic acid causes severe eye and skin burns. Causes severe digestive and respiratory tract burns. Flammable liquid and vapor. May be harmful if absorbed through the skin. Glacial acetic acid solidifies below 62°F (17°C). Corrosive to metal. Target Organs: Teeth, eyes, skin, mucous membranes. Potential Health Effects Eye: Causes severe eye irritation. Contact with liquid or vapor causes severe burns and possible irreversible eye damage. Skin: Causes skin burns. May be harmful if absorbed through the skin. Contact with the skin may cause blackening and hyperkeratosis of the skin of the hands. Ingestion: May cause severe and permanent damage to the digestive tract. Causes severe pain, nausea, vomiting, diarrhea, and shock. May cause polyuria, oliguria (excretion of a diminished amount of urine in relation to the fluid intake) and anuria (complete suppression of urination). Rapidly absorbed from the gastrointestinal tract. Inhalation: Effects may be delayed. Causes chemical burns to the respiratory tract. Exposure may lead to bronchitis, pharyngitis, and dental erosion. May be absorbed through the lungs. First Aid Measures Eyes: In case of contact, immediately flush eyes with plenty of water for a t least 15 minutes. Get medical aid immediately. Skin: In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Get medical aid immediately. Wash clothing before reuse. Ingestion: If swallowed, do NOT induce vomiting. Get medical aid immediately. If victim is fully conscious, give a cupful of water. Never give anything by mouth to an unconscious person. Inhalation: If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid. Notes to Physician: Persons with pre-existing skin disorders or impaired respiratory or pulmonary function may be at increased risk to the effects of this substance. Treat symptomatically and supportively.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





37

Benzotriazole-1,2,3, AF Coolant Contam. Test

Benzotriazole-1,2,3 is hazardous in case of skin contact (irritant), of eye contact (irritant), of ingestion, of inhalation. Corrosive to eyes and skin. The amount of tissue damage depends on length of contact. Eye contact can result in corneal damage or blindness. Skin contact can produce inflammation and blistering. Inhalation of dust will produce irritation to gastro-intestinal or respiratory tract, characterized by burning, sneezing and coughing. Severe over-exposure can produce lung damage, choking, unconsciousness or death. Potential Chronic Health Effects: The substance may be toxic to the nervous system, central nervous system (CNS). Repeated or prolonged exposure to the substance can produce target organs damage. Repeated exposure of the eyes to a low level of dust can produce eye irritation. Repeated skin exposure can produce local skin destruction, or dermatitis. Repeated inhalation of dust can produce varying degree of respiratory irritation or lung damage. First Aid: Eyes - Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Cold water may be used. Get medical attention immediately. Skin - immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Cover the irritated skin with an emollient. Cold water may be used. Wash clothing before reuse. Thoroughly clean shoes before reuse. Get medical attention immediately. Inhalation - remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention immediately. Ingestion - Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. If large quantities of this material are swallowed, call a physician immediately. Loosen tight clothing such as a collar, tie, belt or waistband. Personal Protection - Splash goggles. Synthetic apron. Vapor and dust respirator. Be sure to use an approved/certified respirator or equivalent. Gloves. Storage - Keep container tightly closed. Keep container in a cool, well-ventilated area. Keep container dry. Keep away from heat. Keep away from sources of ignition. Empty containers pose a fire risk,

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





38

BIO-TEK 134 HI-SOLV Cleaning Compound,

Solvent, Microscopic Analyses

BIO-TEK -- 134 HI-SOLV - CLEANING COMPOUND is a clear colorless liquid that is virtually odorless. Avoid strong oxidizers. Prolonged exposure may lead to defatting of the skin. Product is a slight eye irritant. If ingested there is a possibility of nausea. There are no known acute and chronic health hazards. Respiratory Protection: Not normally needed. Ventilation: Local exhaust/mechanical (general): not applicable per manufacturer. Protective gloves: Not normally needed Eye Protection: Not needed. Other Protective Equipment: Not needed. Work Hygienic Practices: None specified by mfr.

39

Chevron FLO-COOL 180, AF Coolant Contam. Test

Chevron FLO-COOL 180 is a lung, skin and eye irritant. Inhalation of mist may cause irritation. Minute amounts aspirated into lungs may cause pulmonary injury. Skin irritation is not normally expected. Prolonged or repeated skin contact may cause irritation. Signs of overexposure include mild irritation, vomiting and diarrhea. First Aid: Inhalation – remove to fresh air. Eye Contact – Flush with water for 15 minutes. Skin Contact – Wash with soap and water. Get medical attention if symptoms persist. Ingestion – Get medical help. Handling: Avoid prolonged and repeated skin contact and splashing in eyes. Use general ventilation if temperatures are excessively high. Use rubber gloves and goggles. Storage: Store materials in a cool, dry place. Moisture may react with strong oxidizing materials such as chlorates, nitrates and peroxides.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





40

COOLANOL 25R, AF Coolant Contam. Test

COOLANOL 25R is toxic, and a skin, eye, and respiratory tract irritant. Eye Contact - If splashed into the eyes, flush with clear water for 15 minutes or until irritation subsides. If irritation persists, call a physician. Skin Contact - In case of skin contact, remove any contaminated clothing and wash skin with soap and water. Launder or dry-clean clothing before reuse. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Inhalation - Vapor inhalation under ambient conditions is normally not a problem. If overcome by vapor from hot product, immediately remove from exposure and call a physician. If breathing is irregular or has stopped, start resuscitation; Ingestion - If ingested, DO NOT induce vomiting; call a physician immediately. Handling and Personal Protection Use product with caution around heat, sparks, pilot lights, static electricity, and open flame. Ventilation - Use local exhaust to capture vapor, mists or fumes, if necessary. Provide ventilation sufficient to prevent exceeding recommended exposure limit or buildup of explosive concentrations of vapor in air. No smoking or use of flame or other ignition sources. Use supplied-air respiratory protection in confined or enclosed spaces, if needed. Use chemical-resistant gloves, if needed, to avoid prolonged or repeated skin contact. Use splash goggles or face shield when eye contact may occur. Use chemical-resistant apron or other impervious clothing, if needed, to avoid contaminating regular clothing, which could result in prolonged or repeated skin contact. Avoid contact with strong oxidants such as liquid chlorine, concentrated oxygen, sodium hypochlorite, calcium hypochlorite, etc., as this presents a serious explosion hazard. Storage Keep containers closed when not in use. Do not store near heat, sparks, flame or strong oxidants. In order to prevent fire or explosion hazards, use appropriate equipment Personal Hygiene Minimize breathing vapor, mist or fumes. Avoid prolonged or repeated contact with skin. Remove contaminated clothing; launder or dry-clean before re-use. Remove contaminated shoes and thoroughly clean before re-use; discard if oil-soaked. Cleanse skin thoroughly after contact, before breaks and meals, and at end of work period. Product is readily removed from skin by waterless hand cleaners followed by washing thoroughly with soap and water.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





41

Diesel Fuel NO. 2, Fuel Detection Meter

Diesel fuel no. 2 is a combustible liquid and vapor. Skin contact: Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention if irritation develops. Hands: Wear gloves that cannot be penetrated by chemicals or oil. The correct choice of protective gloves depends upon the chemicals being handled, the conditions of work and use, and the condition of the gloves (even the best chemically resistant glove will break down after repeated chemical exposures). Most gloves provide only a short time of protection before they must be discarded and replaced. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Inhalation: use only with adequate ventilation. Do not breathe vapor or mist. If ventilation is inadequate, use a NIOSH-certified respirator with an organic vapor cartridge and P95 particulate filter. If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention immediately. Eyes: Avoid contact with eyes use safety glasses with side shields. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention. Ingestion: Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not induce vomiting. Never give anything by mouth to an unconscious person. Get medical attention immediately. Handling: Vapor may cause flash fire. Vapors may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard. Explosive in the presence of the following materials or conditions: open flames, sparks and static discharge and heat. In case of fire, use water fog, foam, dry chemicals, or carbon dioxide. Storage Store in accordance with local regulations. Store in a segregated and approved area. Store away from direct sunlight in a dry, cool and well-ventilated area. Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use non-sparking tools. Take precautionary measures against electrostatic discharges. To avoid fire or explosion, dissipate static electricity during transfer by grounding and bonding containers and equipment before transferring material.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





42

ECOLINK Electron, Rotrode AES Method

ELECTRON is a non-halogenated industrial chemical. It is a skin irritant avoid extended exposure to unprotected skin wear gloves, and Avoid getting it in eyes, or breathing large amounts of the vapor, (it will dry out nasal passages). Used on a rag or from a spray bottle, the product won’t produce fumes in any great quantity, (don’t spray ELECTRON under high pressure without adequate ventilation). Primary Routes of Exposure: Oral, Inhalation, & Skin Ingestion: Swallowing large amounts may be harmful by causing gastrointestinal irritation. Inhalation: Breathing large amounts may be harmful by causing nose, throat, and respiratory tract irritation. Eyes: Irritant. Liquid contact will irritate eyes and may cause stinging, tearing, and redness. Skin or Contact: May cause mild irritation of redness and burning. First Aid: Ingestion: Seek medical attention immediately. If individual is drowsy or unconscious, do not give anything by mouth; place individual on left side with head down. Contact medical facility or poison Control center for advice on whether to induce vomiting. Inhalation: Remove to fresh air. If breathing is difficult, give oxygen. Keep person warm and quiet. Seek medical attention. Eyes: Irrigate immediately with water for at least 15 minutes. Get medical attention if irritation persists. Skin: Wash with soap and water. Thoroughly clean contaminated clothes and shoes before re-use. If symptoms persist, seek medical attention. Personal Protection: Eye Protection Safety glasses and splash protection required. Protective Gloves: Nitrile gloves. Respiratory Protection: Not required under conditions of normal use. If vapor mist is present, use NIOSH certified organic vapor mask. Ventilation: Local exhaust/hood or fan may be used. Other Protective Clothing: None required under normal use. Work Practices: Store rags used with this material in an airtight, metal container to prevent spontaneous combustion. Treat this chemical with respect and follow all MSDS instructions.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





43

Ethylene Glycol, AF Coolant Contam. Test

Ethylene glycol is a toxic material causing immediate and serious toxic effects if swallowed. Symptoms of poisoning may occur after several hours; therefore medical observation for at least 48 hours after the accident. Inhalation: Supply fresh air or oxygen; call for doctor. In case of unconsciousness place patient stably in side position for transportation. Supply fresh air. If required, provide artificial respiration. Keep patient warm. Seek immediate medical advice. Skin Contact: Immediately wash with water and soap and rinse thoroughly. Seek immediate medical advice. Eye Contact: Rinse opened eye for several minutes under running water. Then consult a doctor. Ingestion: Drink lots of water. Induce vomiting if patient is conscious. Call a doctor immediately. Seek immediate medical advice. For safe handling keep container tightly sealed. Store in cool, dry place in tightly closed containers. Ensure good ventilation at the workplace. Store away from oxidizing agents. Store away from water/moisture. This product is hygroscopic. Keep container tightly sealed, protect from humidity and water. In case suitable respirator when high concentrations are present. Use safety glasses, protective work clothing and gloves.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





44

Gasoline, All Grades

Gasoline is an extremely flammable eye and mucous membrane irritant. It affects the central nervous system and is harmful or fatal If swallowed—aspiration hazard. Gasoline has a high fire hazard. Keep away from heat, sparks, open flame, and other ignition sources. Contact may cause eye, skin and mucous membrane irritation. Harmful if absorbed through the skin. Avoid prolonged breathing of vapors or mists. Inhalation may cause irritation, anesthetic effects (dizziness, nausea, headache, intoxication), and respiratory system effects. Contains benzene, which can cause blood disease, including anemia and leukemia. Gasoline is a moderate eye irritant, may cause skin irritation with repeated contact. Practically non-toxic if absorbed. In case of contact with eyes, immediately flush with clean, low-pressure water for at least 15 min. Hold eyelids open to ensure adequate flushing. Seek medical attention. On skin contact remove contaminated clothing. Wash contaminated areas thoroughly with soap and water or waterless hand cleanser. Obtain medical attention if irritation or redness develops. The major health threat of ingestion occurs from the danger of aspiration (breathing) of liquid drops into the lungs, particularly from vomiting. Aspiration may result in chemical pneumonia (fluid in the lungs), severe lung damage, respiratory failure and even death. Ingestion may cause gastrointestinal disturbances, including irritation, nausea, vomiting and diarrhea, and central nervous system (brain) effects similar to alcohol intoxication. In severe cases, tremors, convulsions, loss of consciousness, coma, respiratory arrest, and death may occur. DO NOT INDUCE VOMITING. Do not give liquids. Obtain immediate medical attention. If spontaneous vomiting occurs, lean victim forward to reduce the risk of aspiration. Excessive exposure may cause irritations to the nose, throat, lungs and respiratory tract. Remove person to fresh air. If person is not breathing, ensure an open airway and provide artificial respiration. If necessary, provide additional oxygen once breathing is restored if trained to do so. Seek medical attention immediately. Gasoline contains benzene, a regulated human carcinogen. Benzene has the potential to cause anemia and other blood diseases, including leukemia, after repeated and prolonged exposure. Avoid repeated and/or prolonged skin exposure. Wash hands before eating, drinking, smoking, or using toilet facilities. Do not use as a cleaning solvent on the skin. Do not use solvents or harsh abrasive skin cleaners for washing this product from exposed skin areas. Waterless hand cleaners are effective. Promptly remove contaminated clothing and launder before reuse.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





45

Heptane, Laboratory Grade,

FT-IR Method

Heptane is an extremely flammable liquid and vapor. Vapor may cause flash fire. Aspiration hazard if swallowed - can enter lungs and cause damage. May cause pulmonary edema. Irritating to eyes and skin. Inhalation may cause central nervous system effects. The product is irritating to eyes, skin, lungs and gastro-intestinal tract. Inhalation may cause central nervous system effects. If ingested there is an aspiration hazard and may cause gastrointestinal irritation, nausea, vomiting and diarrhea. May cause adverse chronic liver and kidney effects. First Aid: Eye Contact Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Obtain medical attention. Skin Contact Wash off immediately with plenty of water for at least 15 minutes. Obtain medical attention. Inhalation Move to fresh air. If breathing is difficult, give oxygen. Do not use mouth-to-mouth resuscitation if victim ingested or inhaled the substance; induce artificial respiration with a respiratory medical device. Obtain medical attention. Ingestion Call a physician or Poison Control Center immediately. Do not induce vomiting. Notes to Physician Treat symptomatically. Handling and Storage Use only under a chemical fume hood. Wear personal protective equipment. Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. Use explosion proof equipment. Take precautionary measures against static discharges. Do not get in eyes, on skin, or on clothing. Do not breathe vapors or spray mist. Keep containers tightly closed in a dry, cool and well-ventilated place. Keep away from heat and sources of ignition. Flammables area. Personal Protective Equipment Eye/face Protection Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166. Wear appropriate protective gloves and clothing to prevent skin exposure. Respiratory Protection Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





46

Hexane, Laboratory Grade,

FT-IR Method

Hexane is an extremely flammable liquid and vapor. Vapor may cause flash fire. Aspiration hazard if swallowed - can enter lungs and cause damage. May cause pulmonary edema. Irritating to eyes and skin. Inhalation may cause central nervous system effects. The product is irritating to eyes, skin, lungs and gastro-intestinal tract. Inhalation may cause central nervous system effects. If ingested there is an aspiration hazard and may cause gastrointestinal irritation, nausea, vomiting and diarrhea. May cause adverse chronic liver and kidney effects. First Aid: Eye Contact Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Obtain medical attention. Skin Contact Wash off immediately with plenty of water for at least 15 minutes. Obtain medical attention. Inhalation Move to fresh air. If breathing is difficult, give oxygen. Do not use mouth-to-mouth resuscitation if victim ingested or inhaled the substance; induce artificial respiration with a respiratory medical device. Obtain medical attention. Ingestion Call a physician or Poison Control Center immediately. Do not induce vomiting. Notes to Physician Treat symptomatically. Handling and Storage Use only under a chemical fume hood. Wear personal protective equipment. Keep away from open flames, hot surfaces and sources of ignition. Use only non-sparking tools. Use explosion proof equipment. Take precautionary measures against static discharges. Do not get in eyes, on skin, or on clothing. Do not breathe vapors or spray mist. Keep containers tightly closed in a dry, cool and well-ventilated place. Keep away from heat and sources of ignition. Flammables area. Personal Protective Equipment Eye/face Protection Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166. Wear appropriate protective gloves and clothing to prevent skin exposure. Respiratory Protection Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced.

NAVAIR 17-15-50.2 TM 38-301-2 T.O. 33-1-37-2 CGTO 33-1-37-2





47

MIL-DTL-5624, Jet Fuel JP-5,

Fuel Detection Meter

Jet Fuel JP-5 is a combustible liquid and vapor. Skin contact: Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention if irritation develops. Hands: Wear gloves that cannot be penetrated by chemicals or oil. The correct choice of protective gloves depends upon the chemicals being handled, the conditions of work and use, and the condition of the gloves (even the best chemically resistant glove will break down after repeated chemical exposures). Most gloves provide only a short time of protection before they must be discarded and replaced. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Inhalation: use only with adequate ventilation. Do not breathe vapor or mist. If ventilation is inadequate, use a NIOSH-certified respirator with an organic vapor cartridge and P95 particulate filter. If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention immediately. Eyes: Avoid contact with eyes use safety glasses with side shields. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention. Ingestion: Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not induce vomiting. Never give anything by mouth to an unconscious person. Get medical attention immediately. Handling: Vapor may cause flash fire. Vapors may accumulate in low or confined areas or travel a considerable distance to a source of ignition and

joint oil analysis program manual volume ii...hmws index nbr. hmws page nbr. benzotriazole-1,2,3 37...

Documents