RB0001L

Jeep® CJ

Rear Shackle Mount Section – Left

0001L00

REQUIRED TOOLS Jack Stands or Lift Mig Welder Paint/Primer Locking Pliers Hand Grinder Cutting Wheel or Torch Welding Gloves Welding Hood/Shield Ear & Eye Protection Sockets & Ratchet Fire Extinguisher & Water Rear Spring Shackle Bushings (Pair)

KIT CONTAINS Rear Shackle Mount Section

QTY 1

RB0001L

Jeep® CJ

Rear Shackle Mount Section – Left

1 0001L00

1) PREPARING YOUR VEHICLE Begin by disconnecting your battery prior to starting your installation. Inspect your vehicle for leaking fuel lines, fuel tank and engine components. If you have fuel leaks repair all leaks prior to starting your installation. If your fuel tank is near your welding area remove your tank prior to welding. Remove all combustible items above the work area such as seats, carpets, padding, etc. Keep all flammable materials away from the vehicle work area.

2) PREPARING YOUR WORKSTATION Keep a fire extinguisher and water close by in the case of fire and make sure you always have a designated “Fire Watch” to assist during the cutting or welding phases. Abide by all apprenticed welding safety standards and practices. Always use appropriate welding eye protection, ear protection, and work and fire safety gloves during the installation and within the work area.

WARNING! If you are unsure on how to perform the installation or how to operate any of the required tools listed above, it is HIGHLY advised that you enlist the work of a certified welder/installer. Failure to follow proper safety precautions and instructions may result in serious injury. The user assumes all liability when installing the product.

RB0001L

Jeep® CJ

Rear Shackle Mount Section – Left

2 0001L00

3) PREPARING FOR YOUR INSTALL Lift your vehicle. Remove the left rear wheel and set it out of the way. Support your rear axle using two jack stands for the driver and passenger sides. Drop and remove the gas tank and all cords and tubes associated with it, and plug/cover the remaining tubes to prevent fume leakage. Place it safely outside of your workstation as it poses as a fire hazard during installation.

4) DISCONNECT SPRING SHACKLE Loosen the upper most bolt on the spring shackle and remove it from the shackle mount.

Loosen the lower bolt enough to rotate the shackle down and out of the way, exposing the frame.

5) ESTABLISH CUTTING ZONE Hold the Rust Buster part up to the frame and take note of its measurements. Using a grinding wheel, grind the zone down to bare metal as best as possible. Measure 1.5’’ from the top of the vehicle’s frame and draw a line, tracing the edge. Draw a second perpendicular line just left of the left most slot.

Continue to draw the line around to the inside of the frame, following the gas tank support, 1.5’’ from it and the top edge.

RB0001L

Jeep® CJ

Rear Shackle Mount Section – Left

3 0001L00

6) CUT Begin cutting away the metal along the drawn line, and cutting as close to the bushing, as possible.

Cut as close as possible to the rear cross member and remove the remaining shackle mount material inside it.

7) TEST FIT PART Attempt to push the part into place and over the remaining frame. Take note of any obstructions and cut away.

The part may fit snugly and require force. Ensure the bushing hole is visually aligned with the right side of the frame.

The part should fit over the remnants, and inside the rear cross member. NOTE: If other frame repair components have been installed previously, additional modifications to the frame may be required.

8) WELDING PREP Once the part has been fitted, prepare your weld zones by clearing away any rust or debris, revealing bare metal.

RB0001L

Jeep® CJ

Rear Shackle Mount Section – Left

4 0001L00

Tack weld and/or clamp the part into place.

9) WELD Remove any remaining potential fire hazards on both the vehicle and surrounding area. 100% weld around all edges including the rear cross member.…………………………

10) PAINT AND PROTECT

Coat the work area and part with a primer or other rust inhibitor to help prevent or reduce the risk of rust formation.

… 11) REASSEMBLE VEHICLE

Begin reassembling your vehicle by resecuring your spring shackle and mount. Insert a new bushing according to the manufacturer’s instructions.

Rotate the shackle into place, send the bolt through, and secure the nut onto it. Reinstall your gas tank, cords, and tubes.

Reinstall your wheel. Reconnect your battery.