jawaban soal plc.doc

Post on 02-Jun-2018

235 views

Category:

Documents

1 download

Embed Size (px)

TRANSCRIPT

  • 8/10/2019 Jawaban soal plc.doc

    1/47

    Project 2.1 (Programming Hardwareconfiguration)

    Please define the PLC-hardware used within your station with the STEP 7 software.

    After the configuration, please download it into the PLC.

    Screen shots of the hardwareconfiguration, the bold words are co ands to clic! on, the " #are only co ents "E$TE%# eans clic! left ouse button once or press E$TE%, "doubleclic!# eans double clic! the left ouse button&

    File New "type $a e& P'()*# OK Insert tation I!"#I$ %&& tation

    ' P2 &1 I!"#I$ %&&(1) Hardware"double clic!#

    ' I!"#I$ %&& ' "$K*%&& ail"double clic!#

    * "$K %&& ' $P+*%&& ' $P+ %1, ' - / %1,*1" &,*&"0& "depends on the

    CP+ you use chec! the order no. on thefront left below corner of the CP+# 1.2 "depends on the CP+ you use open the flapof the CP+ and you will find the right ersionnu ber on the left below corner# "doubleclic!#

    *

  • 8/10/2019 Jawaban soal plc.doc

    2/47

    $P+ %1, "at the Slot ' double clic!# $ cle3$loc4 !emor $loc4 !emor 1&& " e ory /yte free definition#

    etenti5e !emor & "$u ber of e ory/ytes Starting with /)# & "$u ber of S7Ti ers Starting with T)# & $u ber of S7Counters Starting with C)# OK

    $P+*%&& ' !*%&& ' 6I36O*%&& !%2% 6I1-36O1-72, 3&89" "depends on theinput0output odule you use refer to the left

    below corner of the odule to find the rightnu ber# "double clic!#

    * I!"#I$ %&& tation a5e and $om:ile

    P;$ 6ownload "follow the instructions onthe screen to download the

    hardwareconfiguration#

    "after download without an error essage switchthe CP+ to %+$ - no red light S1 - -switch the

    CP+ to ST2P again# tation 7it

    '

  • 8/10/2019 Jawaban soal plc.doc

    3/47

    Project 2.2 (Programming 0asics in 6igital #ec

  • 8/10/2019 Jawaban soal plc.doc

    4/47

    P2 &2 "right ouse button on the pro5ect P'()'# Paste

    = "close the pro5ect P'()*#

    P2 &2 Insert Program / Program ' / Program (2) 0loc4s Insert /0loc4 Function

    F06 "change progra ing language of 1C* to 1/3 1unction /loc! 3iagra #

    OK

    8

  • 8/10/2019 Jawaban soal plc.doc

    5/47

    7ecution36ocumentation

    Edit the 2rganisation /loc! * first by double clic! on 2/*.

    Progra 2/*&

    After editing# File a5e "no erroressage# File 7it

    This procedure is always the sa e afterediting a progra it9s not entionedany ore:::

    Progra 1C*&

    0loc4 P;$ 6ownload "followthe instructions on the screen#

    4

  • 8/10/2019 Jawaban soal plc.doc

    6/47

    Project 2.% (Programming 0asics in 6igital #ec

  • 8/10/2019 Jawaban soal plc.doc

    7/47

    7ecution36ocumentation

    Progra 2/*

    Progra 1C4&

    7

  • 8/10/2019 Jawaban soal plc.doc

    8/47

    Project 2., (Programming 0asics in 6igital #ec

  • 8/10/2019 Jawaban soal plc.doc

    9/47

    Project 2.9 (Programming 0asics in 6igital #ec

  • 8/10/2019 Jawaban soal plc.doc

    10/47

    Project 2.- (Programming 0asics in 6igital #ec

  • 8/10/2019 Jawaban soal plc.doc

    11/47

    Project 2./ (Programming $ondition $all of a Program)After a short actuation of a Start-button, the piston rod of the cylinder with singlesolenoid shall o e as long as a %eset- or a Stop-button is pressed shortly. The prograshall be acti ated by the Auto0 anu switch, the progra 1C> is not running if theAuto0 anu switch is off.

    7ecution36ocumentation

    Progra 2/*

    Progra 1C>

    **

  • 8/10/2019 Jawaban soal plc.doc

    12/47

  • 8/10/2019 Jawaban soal plc.doc

    13/47

  • 8/10/2019 Jawaban soal plc.doc

    14/47

    Progra 1C*

    *8

  • 8/10/2019 Jawaban soal plc.doc

    15/47

  • 8/10/2019 Jawaban soal plc.doc

    16/47

    Project 2.1& (Programming Off*6ela *#imer function)

    ;f a Start-button is pressed, the Start-light "

  • 8/10/2019 Jawaban soal plc.doc

    17/47

    Project 2.11 (Programming $ounter 6own function)

    ;f a Start-button is pressed, the piston rod of the cylinder o e until reaching the sensor for the front0bac! position depending on the hardware and then o e bac! to startingcondition auto atically. After starting 4 ti es, the Start-light ust be on and the pistonrod can not o e again. Set the counter by pressing the %eset-button once.

    7ecution36ocumentation (6istri>ution tation)Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    The logic odule P " *).)# is an edge e ory this eans, e en you hold Start-button down,only a short pulse will co e through to the input. So e contact shatter or bounce e en you

    press the only once.

    7ecution36ocumentation (#esting tation)Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    *7

  • 8/10/2019 Jawaban soal plc.doc

    18/47

    7ecution36ocumentation (Handling tation)Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    7ecution36ocumentation ( orting tation)

    *>

  • 8/10/2019 Jawaban soal plc.doc

    19/47

    7ecution36ocumentation (" tation)

    *?

  • 8/10/2019 Jawaban soal plc.doc

    20/47

    Project 2.12 (Programming Programming of a Flas

  • 8/10/2019 Jawaban soal plc.doc

    21/47

    Project 2.1% (Programming Programming of a "uto3!anu seCuence)

    The starting condition for this pro5ect is to press the Start-button shortly. After the Start-

    button was pressed shortly, the Start-light is on for * second. After the Start-light is off,

    the %eset-light is on for 6 seconds cycle end. To newstart the cycle, either press Start-

    button again " anu-cycle#, or switch the Auto0 anu-switch to on.

    7ecution36ocumentation

    Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    '*

  • 8/10/2019 Jawaban soal plc.doc

    22/47

    Project 2.1, (Programming !o5e to tarting Position)

    o e your station auto atically to the starting position "ho e position#, this eans,this is the position where a aterial flow starts. Press the %eset-button shortly to startthe seDuence. Station is not in starting position, the %eset-light shall flash with 4)) s,

    Station is in starting position, the %eset-light is on.

    $onditions of 6istri>ution tation?C* acuum sensor is off (not I&.%)C' wi5el arm is in magaDin :osition (I&.,)C6 Eor4:iece sensor is off (not I&.-)C8 !agaDine is in >ac4 :osition (I&.1)

    Actions&the actions ha e to be done if the corresponding condition is not fulfilled.

    A* remo5e t

  • 8/10/2019 Jawaban soal plc.doc

    23/47

    $onditions of #esting tation ?

    C* isual control no wor4:ieces are on t

  • 8/10/2019 Jawaban soal plc.doc

    24/47

    $onditions of Handling tation ?

    C* isual control no wor4:ieces are on t

  • 8/10/2019 Jawaban soal plc.doc

    25/47

    $onditions of orting tation ?

    C* witc< 1 is in front :osition (I&.9)C' witc< 2 is in >ac4 :osition (I&.-)C6 no wor4:iece at t

  • 8/10/2019 Jawaban soal plc.doc

    26/47

    $onditions of " tation ?

    C* isual control no wor4:ieces are on t

  • 8/10/2019 Jawaban soal plc.doc

    27/47

    '7

  • 8/10/2019 Jawaban soal plc.doc

    28/47

    Project 2.19 (Programming 7:anded mo5ement to tarting Position)

    E@pand the Pro5ect before, that the %eset-button ha e to be pressed shortly in any case toa!e sure, the isual chec! is done already. 1ollow the steps&

    1. Reset-button not pressed shortly Reset-light fash with 500 ms2. Reset-button was pressed shortly and Station is in home position

    Reset-light is on2. Reset-button was pressed shortly and Station is not in home position

    Reset-light fash with 200 ms as long as the actuator (actuators mo!e tohome position"a#ter reaching the home position" the Reset-light is on.

    $. %ress Start-button shortly Reset-light is o&" Start-light is on

    The whole process "

  • 8/10/2019 Jawaban soal plc.doc

    29/47

    '?

  • 8/10/2019 Jawaban soal plc.doc

    30/47

  • 8/10/2019 Jawaban soal plc.doc

    31/47

    7ecution36ocumentation ( #esting tation )Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    6*

  • 8/10/2019 Jawaban soal plc.doc

    32/47

    6'

  • 8/10/2019 Jawaban soal plc.doc

    33/47

    7ecution36ocumentation ( Handling tation )Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    66

  • 8/10/2019 Jawaban soal plc.doc

    34/47

    68

  • 8/10/2019 Jawaban soal plc.doc

    35/47

    7ecution36ocumentation ( orting tation )Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    64

  • 8/10/2019 Jawaban soal plc.doc

    36/47

    6=

  • 8/10/2019 Jawaban soal plc.doc

    37/47

    7ecution36ocumentation ( " tation )Progra 1C*, the progra 2/* is the sa e than for the pro5ect before

    67

  • 8/10/2019 Jawaban soal plc.doc

    38/47

    6>

  • 8/10/2019 Jawaban soal plc.doc

    39/47

    2.1- Project 0asics of I3O communicationPlease co plete the following graphics according the description.

    7ecution36ocumentationPlease define a * /it bidirectional co unication networ!&

    2 4 V D C0 V I n p u t O u t p u t

    P N P2 4