jamieson fence supply - caddetails can open to either side- eliminating the need ... cantilever gate...
TRANSCRIPT
JAMIESON FENCE SUPPLY GATE PRODUCTS AND PHOTO GALLERY
“24 locations with the products you want, the support you need and the service you deserve.”
Traditional Steel Pipe Gates
V-Track
cantilever gates
Aluminum Cantilever Gates
TrusTrac™ Single Track Gates
TrusTracII™ Double Track Gates
Box Gates
PowerTrac™ Cantilever
PowerTrac™ Canted Wheel
Aluminum V-Track Gates
ValuTrac™ Slide Gates
Overhead I-Beam Track Gates
I-Trac™
Crash Gates
CGS™ Crash Gate Systems
Custom Gates
SLIDE GATE PRODUCTS
… to Homeland Security
Residential and Commercial…
Filler materials extend through the tail section
of each gate for safety and symmetry. Thus, each
gate can open to either side- eliminating the need
to specify opening direction.
Jamieson’s TrusTrac™ gates are a premier line
of aluminum cantilever sliding gates.
Utilizing our proprietary truck and enclosed
track system, this single panel gate can span
large gate openings with minimal deflection or
resistance. All gates are fabricated and fully
welded under factory controlled conditions,
ship ready for immediate installation ¹ and
include all hardware for manual operation.
TrusTrac™ Gate Series Typical use
Max single
drive gate
opening
Max double
drive gate
opening
TrusTrac™ Series 1000 Standard use 22’ 44’
TrusTrac™ Series 2000 Medium duty use 28’ 56’
TrusTrac™ Series 3000 Heavy duty use 34’ 68’
TrusTracII™ Series 3000 Heavy duty use with large gate openings 40’ 80’
¹ Where the overall length of the gate exceeds
shipping constraints, the gate is shipped in two
sections with prefabricated splice provisions for
simple reassembly at the job site.
At the heart of each TrusTrac™
gate is Jamieson’s proprietary
truck and track system. Our 10”
truck assembly is unequalled in
the industry. Each of the (8)
wheels on our truck assemblies
are cylindrical bearings with a
5,400 lb static load. With a
robust body and mounting system,
the entire truck assembly has
been tested and certified for a
17,500 lbs peak load.
TrusTrac™ geometry and section
widths are specifically designed
for increased strength and
rigidity to resist deflection over
long spans and in high wind-load
conditions. Our 6061-T6
aluminum track extrusion weighs
4.8 lbs/ft by itself- over 6½
lbs/ft in conjunction with the top
horizontal member!
TrusTrac™ gate frames are constructed
from durable 6063-T52 structural aluminum
to provide maximum life, durability and rust
resistance.
Each gate is custom fabricated to the exact
opening to achieve superior balance, rigidity
and squareness. Each bay is equidistant, a
maximum of 6’ wide and braced with solid
gusset plates.
End bays include additional heavy wall
bracing to provide additional strength,
greater chain link tension (if applicable)
and the opportunity to relocate operator
chain brackets or drive rail from the end
of the gates- thus eliminating a
protrusion.
Whether creating original ornamental
concepts, matching to custom fencing,
eliminating riveted/field assembled gates,
designing for high security or unique
applications, our Engineering and custom
fabrication team specialize in creating custom
designs, specifications and manufacturing the
gate to meet your requirements.
CUSTOM DESIGNS & FABRICATION
F2200 and UL325 Compliant
Match Existing or Custom Fence
Square, Round, Solid or Tubular
Pickets
Custom Arched Rails
Ameristar® Impasse® Pales
80’ Double Drive Ornamental
Cantilever Gate
11’-6” tall x 45’ Double Drive Custom
Ornamental Cantilever Gate
TrusTrac™ Gate Series Typical use
Max single
drive gate
opening
Max double
drive gate
opening
PowerTrac™ Series 4000 Cantilever Box Gate 60’ 120’
PowerTrac™ Series 4100 Canted Wheel Box Gate (Track) 200’ 400’
Jamieson’s PowerTrac™ gates are a premier line
of aluminum box frame sliding gates. Utilizing
our robust design, these gates can span large
openings with ease of movement and minimal
deflection. PowerTrac™ gates are available as
cantilever (Series 4000) or ground track
(Series 4100).
PowerTrac™ gates have been certified to 130 MPH wind loads in coastal locals. As site
conditions (soil, wind exposure level, building codes, etc) are an essential element of the
evaluation, Jamieson provides an option for your job-specific wind-load certifications.
Series 4000 Cantilever Box Gates
Jamieson’s Series 4000 PowerTrac™ Cantilever
Gates utilize our proprietary heavy duty truck
assemblies and enclosed track system. As with
our premier TrusTrac™ gate products, each of
the (4) 10” heavy duty truck assemblies have
been tested and certified for a 17,500 lbs
peak load.
PowerTrac™ Box Gates are designed and
manufactured to meet your standard or
unique aesthetic requirements. Our
Engineering team and custom fabrication
shop can provide design support, develop
3 part specs & manufacture the gate to
meet your requirements. Mill finish
aluminum & powder coated finishes are
available.
Series 4000 Box Gate Construction
PowerTrac™ gate frames are
constructed from durable 6063-T52
structural aluminum to provide maximum
life, durability and rust resistance.
Enhanced material weight & usage
provides additional strength and
support in critical frame areas for
greater impact and wear resistance.
Each gate is custom fabricated to
achieve superior squareness, balance
and rigidity. All bay widths are ≤ 6’
wide, equidistant and braced with (4)
welded solid gusset plates. A minimum
of (3) cross braces per primary vertical
member and alternating diagonal cross
braces top & bottom span the length of
the gate to join the front and rear
panels as a rigid, single piece box frame.
Unless otherwise requested, filler
materials (such as chain link) are
factory installed with splicing
provisions (sleeves, drilled holes &
hardware) and all hardware for manual
operation provided. Simple re-assembly
and installation is provided for at the
job site.
Jamieson’s Series 4100 PowerTrac™ Canted
Wheel Box Gates are a ground track
aluminum frame box gate system designed
for very large gate openings (up to 200’
single drive gate openings).
208’ Single Drive Canted Wheel Gate
The entire gate length is fabricated
in modular 24’ foot sections in the
manufacturing facility to ensure
squareness, parallelism and
integrity. the gate is separated into
halves to meet shipping constraints.
Filler materials such as chain link or
ornamental pickets are factory
installed. Splicing provisions (sleeves,
drilled holes & hardware) and all
hardware are provided for manual
operation. Simple re-assembly and
installation is provided for at the job
site.
• 3” square gate frame, 2” sq. primary
verticals diagonal cross bracing 1” sq.
• I Beam Rail system with steel rebar
anchors fabricated at Jamieson and
galvanized after fabrication
• Fabricated and assembled wheel
assemblies & Cradles, galvanized after
Fabrication
-Track Slide Gates
¹ Where the overall length of the gate exceeds
shipping constraints, the gate is shipped in two
sections with prefabricated splice provisions for
simple reassembly at the job site.
Jamieson’s ValuTrac™ Aluminum V-Track
Sliding Gates are capable of spanning large
openings with stability unequaled in the
industry. All gates are fully welded under
factory controlled conditions.
Each gate series is constructed from specific
structural members determined by the
application and gate span to strengthen the
gate and improve stability.
ValuTrac™
Gate Series Typical use
Max single
drive gate
opening
Max double
drive gate
opening
Series 1500 Standard use 20’ 40’
Series 2500 Medium duty use 30’ 60’
Series 3500 Heavy duty use 50’ 100’
Series 4500 Heavy duty use with large gate openings 60’ 120’
-Track Slide Gates
constructed from durable 6063-T52
structural aluminum to provide
exemplary life, durability and rust
resistance.
custom fabricated to the exact
opening to achieve superior balance,
rigidity and squareness.
Each bay is equidistant, a maximum of
6’ wide and braced with (4) welded solid
gusset plates.
-Track Slide Gates
End bays include a heavier wall vertical
member with horizontal bracing and a
second vertical support member provide
improved durability, greater chain link
tension (if applicable) and the opportunity
to relocate operator chain brackets or
drive rail from the end of the gate- thus
eliminating a protrusion.
6-inch solid steel power wheels
weighing 12.5 lbs each with 5,000
lb capacity and sealed bearings are
included with each ValuTrac™ gate
produced. The wheels are mounted
inside custom wheel-wells to
maintain low ground clearance. The
wheels are maintenance free with
no grease fittings.
HEAVY DUTY MAINTENANCE
FREE WHEELS:
I- -Beam Gates
I-Trac™ Gate
Series Typical use
Max span
of opening Gate Frame Material
Series 6200 Industrial, commercial & security applications 20’ Aluminum & Steel
Series 6300 Heavy duty, high security applications 30’ Aluminum & Steel
Series 6400 Heavy duty, large openings, high security 45’ Aluminum
Series 6600 Heavy duty, very large openings, high security 60’ Aluminum
Jamieson’s I-Trac™ gate systems are a
complete line of overhead I-Beam sliding
gates for correctional facilities, Sally
ports & high security applications. Single
or double drive gate openings can range up
to 16’ maximum clear height and spans of
60’ on the aluminum gate series & 30’ with
steel.
engineered for wind loads up to
110 MPH @ Wind Exposure ‘C’.
As most typical I-Trac™ gates exceed shipping
constraints, the gate is shipped in sections with
splice provisions for simple and immediate reassembly
at the job site.
I- -Beam Gates
• designed to the exact span, weight &
wind load.
• designed for strength, balance,
rigidity and endurance.
• AWS certified manufacturing
operations
• Complete system package
(superstructure plus gate).
• Adjustability in each bay through the
entire gate length.
• Filler materials extend through the
tail section of each gate, thus making
each gate reversible and able to open
to either side.
I- -Beam Gates
Jamieson’s proprietary aluminum track is
mounted to the bottom of the engineered
I-Beam at the factory for perfect
alignment, optimal splice locations (if
applicable) and ease of installation at
the job site. The enclosed track
provides 2,500 lb vertical reaction
load, eliminates snow or ice buildup and
potential tampering that can be found
with external rollers.
Heavy duty 10” truck assemblies, each
with (8) 5,400 lb cylindrical bearings,
are certified for a 17,500 lbs peak load.
The quantity of trucks required is based
on the opening & gate length and are
mounted to the top of the gate frame to
carry the gate with high reliability and
minimal resistance. Posts, double post assemblies and
hanging brackets are designed and
fabricated to the specific application.
I- -Beam Gates
There are few limitations to securing, latching
or locking I-Trac™ gates. Whether manual,
electronic or hydraulic, Jamieson can assist in
selection, system design, integration, 3-part
specifications and supply.
Our goal is to provide you the highest quality
gate system with simplified installation and high
reliability.
Security Gates
Jamieson’s Crash Gate Systems (CGS™) can
adapt any Jamieson proprietary sliding
gates to K4, K8 or K12 engineered crash
ratings.
All CGS™ assemblies include Gate,
Superstructure, cable systems, locking
column, bollard posts and automation for
total system requirements.
Please call Jamieson for more detailed
information.
· PIPE CANTILEVER GATES
· TRUSTRAC™ ALUMINUM
ENCLOSED TRACK
CANTILEVER GATES
· VALUTRAC™ V-TRACK
GATES
· I-TRAC™ OVERHEAD I-BEAM
GATES
· POWERTRAC™ CANTILEVER
BOX GATES
· POWERTRAC™ CANTED
WHEEL BOX GATES
Welded & bent frame residential gates
Pre-fabricated pedestrian gates
Ornamental Estate Swing Gates
Large opening swing gates
Specialty and Custom Gates
SWING GATE PRODUCTS
PRE-HUNG FOR EASE OF INSTALLATION
LATCHING AND ACCESS CONTROL OPTIONS
PRE-SET HINGES FOR EASE OF INSTALLATION
FILLER CHOICES AVAILABLE
HYDRAULIC DOOR CLOSER (OPTION)
SERIES 8000 PRE-FAB PEDESTRIAN GATES
Jamieson’s Series 8000 pre-hung pedestrian (walk)
gates ship ready for immediate installation at the
jobsite. All gates and components in this series are
manufactured and assembled by our team of
fabricators and assemblers to meet your custom
specifications.
SERIES 8000 PRE-FAB PEDESTRIAN GATES Series 8000 gate installation is simply a matter of
setting the two posts in concrete piers. The bottom
cross-brace is removed or set in a shallow trench
excavated between the footings. The gate is then
inserted into the footing, braced upright and concrete
poured.
Where magnetic latches or electronic access control
features are pre-assembled, all wiring is run at the
factory and fed through a ¾” coupling 6” below grade
on the latch side of the gate.
There are almost as many ways to gain entry or exit a gate as there are gates. Most
options required are difficult products to field assemble- such as magnetic, electronic or
combination locks, panic bars, hydraulic closers and so forth. Our specialty is to provide
you custom products preassembled in a factory controlled environment by our team of
installation experts. This means better quality controls for you and a more efficient and
cost effective means of installation.
SERIES 8000 PRE-FAB PEDESTRIAN GATES
Standard Series 8000 gate frames are
manufactured from 2” square x 3/16”
wall heavy steel tubing with 4” posts.
The posts can be round schedule 40
(typical for chain link) or square heavy
wall (ornamental). Cross-bracing
between the posts above & below the
gate frame provides rigidity,
squareness and stability during
transportation and installation.
The gate is welded to the door frame
with Elite Power Hinges. These hinges
are heavy duty and super quiet with
double ball bearings that pivot on a
3/4" ground and tempered solid
stainless steel shaft. They are
maintenance free and self lubricating
to provide long life with free gate
movement. The weight capacity per
pair is 1000 lb.
SERIES 8000 PRE-FAB PEDESTRIAN GATES
For gates installed between existing
columns or posts, Jamieson applies the
same fit-for-use and installation friendly
principles. Our pre-fabricated hinge
plates include either fixed or adjustable
barrel hinges with the mating
requirements either pre-drilled or
fabricated onto the opposing half of the
gate frame. At installation, it is only a
matter of determining location, then
drilling and lagging the hinge plate to
the column/post followed by hanging
the pre-set gate frame.
The completed product is available with
either a galvanized or powder coated finish
to match the aesthetics of the project.
Material substitutions are welcome and our
design team will assist with custom
drawings and specifications to meet your
specific application.
SERIES 8400 ESTATE GATES
Jamieson’s Series 8400 Estate gates are
custom designed and manufactured aluminum
and steel frame ornamental single and double
drive swing gates. These gates are ideally
suited for residential and light commercial
properties.
All gates are fully welded under
factory controlled conditions, ship
ready for immediate installation and
include all hardware for manual
operation.
Automation and associated hardware
integration can be designed, specified
and supplied by Jamieson.
SERIES 8400 ESTATE GATES
From the simple to the elaborate, Jamieson can
incorporate your standard or unique
ornamental design into our proven durable
gates.
Standard and custom powder coated colors are
available. Material substitutions are welcome
and our design team will assist with custom
drawings and 3-part specifications to meet your
specific application.
For those projects that require:
• a higher quality gate than typically
provided by mass producers or
importers of fence panels
• a collaborative effort to match your
design concept into a well built gate
frame.
• a flexible company that works with
you
• design expertise and custom
manufacturing capabilities.
SERIES 8400 ESTATE GATES
Series 8400 gate frames are made from
domestic materials and are more
substantial than typically used by most
conventional manufacturers. Our
manufacturing operations custom fabricate
each product to our exacting standards
with AWS certified welders and welding
procedures.
Jamieson applies fit-for-use and
installation friendly principles from
design through manufacturing. As such,
there is minimal to no gate assembly at
the job site.
All gates (within shipping constraints)
are 100% welded in the controlled
environment of our manufacturing
facility.
SERIES 8400 STADIUM GATES
The result is a solid weldment that doesn’t
rattle when used and there is no
assembling numerous parts that can be
lost or missing.
all hinges and hardware are preinstalled
(if possible) at the factory and include a
complete range of hinges from self-
closing to high weight capacity. We also
provide an option for custom hinge plates
for installation between existing columns
or posts.
installation is simply a matter of setting
the posts or mounting the hinge plate.
With minimal assembly, there is minimal
packaging and cleanup required after
installation.
LOGOS AND INSTALLED FEATURES • STEEL & ALUMINUM
• CUSTOM CAD DESIGNS
• CUSTOM MATCHED COLORS
• LASAR, PLASMA & WATER JET
CUTTING CAPABILITIES
• MULTILE FRAMING & MOUNTING
OPTIONS
Our specialty is to provide you custom
products preassembled in a factory
controlled environment by our team
of installation experts. This means
better quality controls for you and a
more efficient and cost effective
means of installation.
There are many different devices
used to control access or
exiting through a gate. Fitting
these devices to a gate in the
field can be difficult, time
consuming and potentially cause
significant damage to gate
appearance.
¹ Where the overall length of the gate exceeds
shipping constraints, the gate is shipped in two
sections with prefabricated splice provisions for
simple reassembly at the job site.
XLG Gate Series Frame Materials
Max single
drive gate
opening
Max double
drive gate
opening
Series 8630 3” square frame, 2” x 3” internal vertical members 30’ 60’
Series 8650 2” x 5” frame, 4 ½” x 3” I-Beam vertical members 60’ 120’
SERIES 8600 LARGE OPENING GATES
Jamieson’s XLG Series 8600 gates are custom
manufactured aluminum frame swing gates for
very large gate openings. These gates are ideally
suited for Industrial, Commercial, Governmental
or other security sensitive applications. All
gates are fully welded under factory controlled
conditions, ship ready for immediate installation
and include all hardware for manual operation.
SERIES 8600 LARGE OPENING GATES
Series 8600 gate frames are made from
durable structural aluminum and
fabricated by AWS certified welders and
welding procedures. Each gate is custom
fabricated to Jamieson’s exacting
standards and braced with solid gusset
plates to maintain squareness and
rigidity. Stainless steel aircraft truss
cable assemblies with adjustable
turnbuckles are installed throughout
the entire gate length to provide both
significant and fine tuning adjustments.
Hinge vertical members are from heavy wall
tubing, predrilled and sleeved for the mating
hinge. In chain link applications, both end
vertical members are reinforced with
horizontal bracing and an additional vertical
support member for greater chain link
tension.
Internal primary and intermediate vertical
members are sized to the application to
provide superior stability and sway
resistance.
71’ DOUBLE DRIVE SWING GATE
SERIES 8600 LARGE OPENING GATES
HINGES AND THE XLG
SUPPORT PACKAGE
Jamieson has a full line of hinge
assemblies for Series 8600 gates that
range up to a 3,000 pound capacity per
hinge.
The Series 8600 XLG Support Package
consists of an upper truss cable
assembly (either one or two depending
on panel length), a hinge-end vertical
member extension, an extended gate
post, brackets and upper hinge.
The XLG Package includes an extended
vertical hinge member and additional
hinge above the gate. Opposite this
hinge is a mounting bracket that swings
with the gate and has a stainless steel
aircraft truss cable attached. This
cable extends approximately 2/3 of the
gate length, which is then attached to
a turnbuckle and bracket welded to
the top horizontal member. The
turnbuckle can then adjust the gate
to the correct elevation.
120’ DOUBLE DRIVE
SERIES 8600 LARGE OPENING GATES
Post and footing sizes and
specifications are functions of state
& local specifications and
regulations, soil conditions, wind
load, size/weight of the gate, wind
blockage of the infill and
potentially other job specific
conditions.
Actual design and specifications must
be determined specifically for the
project by Jamieson, the Architect,
Engineer of Record or other
technically capable resource.
Complementing our
branch capabilities is
our Access Control &
Engineered Gate
Division, headquartered
in Houston, Texas. This
resource provides
state-of-the-art
technical & design
support with enhanced
fabricating capabilities.
ENGINEERING & MANUFACTURING CENTER
Certified to AWS D1.1/D1.1M and D1.2/D1.2M
POST TRUCK BRKT. U-BOLT LOWER GUIDE BRKT. COLLECTOR
4" ROUND 274003-E4 209007 274005-UL 274011-UL
4" SQUARE 274003-E4 209007-SQ 274005-UL 274011-UL
6 5/8" ROUND 274003-E6 200000-265 274005-6 274012-UL
6" SQUARE 274003-E6 200000-269 274005-6 274012-UL
TABLE III: HARDWARE GUIDE
WIRE SIZE
3/16"
1/4">30' 1/2" x 6"
TABLE IV: CABLE TRUSSING
GATE OPENING TURNBUCKLE SIZE
<30' 3/8" x 6"
EXTENDED TRUCK BRACKET(REF. TABLE III)
TABLE 1: TRUCK ASSEMBLY CRITERIA:
TRUSS CABLE(REF. TABLE IV)
BOTTOM HORIZONTAL
CABLE CLAMP
9 GA. SMOOTH WIRE
TENSION BAR
1/4" GUSSETTYP AT EACH CORNER/ EACH BAY
TURNBUCKLE(REF. TABLE IV)
SQUARE/ ROUND UL COLLECTOR(REF. TABLE III)TOP HORIZONTAL
BARBWIRE 4 PT. 12.5 GA.(OPTIONAL)
T6061-T6 ALUM. TRUSS TRAC
LOWER GUIDE BRACKET(REF. TABLE III)
3" UL BOX ROLLERS
> 24'
GATE OPENING
= 24'
274010
PARTNUMBER
274006
10"
LENGTH
6"
8
# BEARINGS/ WHEELS
4
NOTE: ALL SERIES 3000 GATES USE 10" TRUCKS
Single Track Parts List:
INSTRUCTION MANUALS
Recommended Tools:
Tape measure
Surveyors instrument
String line
Stakes
String line level
24” to 48” Carpenter’s level
Post hole auger (or digger)
Cement Trowel
Fence Pliers
Standard (flat) screwdriver
15/16” Open end wrench
15/16” Socket, ratchet & drive extension
¾” socket or open (or box) end wrench
6” or 8” crescent wrench
CUSTOM MANUALS & SPECIFICATIONS
ENGINEERING
Solid Models
Jamieson’s in-house engineering
capabilities include 3D CAD drafting
and solid modeling. This is used for
any applicable custom product to
check fit, form & function on moving
parts, determine weights and balance,
optimize center of gravity, create
detailed manuals and to simplify
installation at the job site.
ANIMATION FOR FIT-FORM-FUNCTION
fit-form-function
& visualization
Animation
Detailing
PROJECT SUPPORT Our Engineering Center provides
total quality in the design, lay out
and fabrication of your total
requirement, making your product
fit-for-use to simplify installation
at the job site.
• All custom gates run-off at factory
before shipping
• All products assembled and
fabricated to fullest extent possible
PENTAGON RAILING
• 18 ELEVATION (SLOPE) CHANGES
• 860’ PRE-FABRICATED RAIL SECTIONS
• 84 UNIQUE PLATED POSTS WITH
DESIGNATED LOCATION TO FOLLOW SLOPE
• STAINLESS MARINE TURNBUCK/CABLE
Assembly
AWS certified
Testing
HARDWARE Jamieson provides a complete line of gate
hardware and accessories. Our
manufacturing operations are certified to
AWS D1.1/D1.1M and D1.2/D1.2M and
provides the technological & manufacturing
expertise to provide for custom
applications. Compliant to UL325 & ASTM
F2200-02 Safety Standards
Cantilever Gate
Hardware
Fittings
Gate
Hardware
12300-A AMELIA DRIVE
HOUSTON, TX 77045
888/286-3362
WWW.JAMIESONFENCE.COM
FOR FURTHER INFORMATION
WWW.ASTM.ORG
WWW.DASMA.COM
WWW.UL.COM
Jamieson is committed to providing quality perimeter security products and services. Because
safety is an important part of Jamieson's design and manufacturing criteria, we follow the
standards developed by Underwriter’s Laboratory (UL 325) and ASTM F2200 as developed by
ASTM International. While these safety standards are specific to automated gates, Jamieson
also chooses to apply them to manual gates to restrict hazards such as protrusions, pinch
points and entrapment zones. As such, our engineering & manufacturing team has developed a
full line of compliant components & hardware. All access control products that we offer
are specifically selected for the proper class of gate usage.
SAFETY POLICY
USE PROPER CARE & PRECAUTION AT ALL
TIMES WHEN OPERATING GATES
NEVER “RIDE” THE GATE
ALWAYS USE PROPER SAFETY EQUIPMENT WHEN SERVICING
GATE OR GATE HARDWARE
DO NOT DISABLE , REMOVE OR MODIFY ANY SAFETY
FEATURES FROM THE PRODUCT
INSTALL ALL WARNING SIGNS & PLACARDS
DO NOT ADD ANY FEATURES THAT PROTRUDE FROM THE BODY OF
THE GATE GREATER THAN ½”
THERE IS NO SUBSTITUTE FOR COMMON SENSE
CORPORATE OFFICE
P.O. Box 769008 Dallas, TX 75376-9008
214-339-8384
800-527-6464 Fax: 214-337-2061
MANUFACTURING & ENGINEERING
12300-A Amelia Drive
Houston, TX 77045-4814 713-434-7907
888-286-3362
Fax: 713-434-7924
JAMIESON LOCATIONS
GEORGIA MISSOURI TENNESSEE TEXAS TEXAS TEXAS
50 Bellamy Court 5201 East 9th Street 405 Hillcrest Drive 9520 Brown Lane 4343 Forest Lane 6504 Smithfield Road
Stockbridge, GA 30281 Kansas City, MO 64124 Bluff City, TN 37618 Austin, TX 78754 Garland, TX 75042 North Richland Hills, TX 76182
678-379-4006 816-231-1062 423-391-0500 512-837-7808 972-494-3200 817-498-0347
888-400-8332 800-777-2584 888-391-0501 800-777-1106 800-777-3245 866-498-0347
Fax: 678-379-4007 Fax: 816-231-6088 Fax: 423-391-0580 Fax: 512-837-8135 Fax: 972-276-0783 Fax: 817-498-6455
LOUISIANA OKLAHOMA 2709 John Deere Drive 10813 I-35 South 14214 Aldine Westfield 6916 N.E. Loop 410
3116 S. Council Road Knoxville, TN 37917 Burleson, TX 76028 Houston, TX 77039 San Antonio, TX 78219
7335 Julie Frances Drive Oklahoma City, OK 73179 865-540-9983 817-293-6972 281-590-5097 210-433-7267
Shreveport, LA 71129 405-745-6969 877-740-9983 866-510-5796 800-777-5097 800-777-1143
318-687-4433 800-777-6404 Fax: 865-540-5146 Fax: 817-551-5734 Fax: 281-590-5148 Fax: 210-661-5581
800-777-4435 Fax: 405-745-6886
Fax: 318-687-4487 2345 Frisco 1915 Empire Central 12300-A Amelia Drive 12930 Sugar Ridge Blvd
Memphis, TN 38114 Dallas, TX 75235 Houston, TX 77045 Stafford, TX 77477
MINNESOTA 5305 S 24th West Ave 901-743-8282 972-241-5827 713-434-7907 281-879-6200
Tulsa, OK 74107 888-892-3362 800-777-5827 888-286-3362 888-268-3362
3401 85th Avenue 918-770-0813 Fax: 901-743-1742 Fax: 972-247-5769 Fax: 713-434-7924 Fax: 281-879-5558
Minneapolis, MN 55443 866-242-0040
763-424-7950 Fax: 918-447-3746 4221 Platinum Way 1143 W. Hurst Blvd 5004 FM 2767
800-777-2430 Dallas, TX 75237 Hurst, TX 76053 Tyler, TX 75708
Fax: 763-424-2422 214-339-8384 817-772-8001 903-597-0463
800-527-6464 800-591-8505 800-777-5988
MISSISSIPPI Fax: 214-337-2061 Fax: 817-772-8002 Fax: 903-595-3221
815 Hwy 475 South 9650 John W. Elliott Dr. 1310 Jarvis Street
Pearl, MS 39208 Frisco, TX 75033 Lubbock, TX 79403
601-936-4111 469-252-8075 806-744-2977
866-936-3362 800-442-6283 800-777-2978
Fax: 601-936-9987 Fax: 469-252-8078 Fax: 806-741-1998