item # description qty 1a smokeless tobacco …...2d unit dimensions: polybagged kit unit weight:...

IT E M # D E S C R IP T IO N Q T Y

1A S M O K E LE S S T O B A C C O S P R IN G LO A D T R A Y 1

S M O K E LE S S T O B A C C O S P R IN G LO A D T R A Y , 1 P A C K ADJUSTABLE WIDTH PUSHER KIT & ADD-ONNARROW WIDTH PUSHER KIT & ADD-ON

PAGE 1 OF 14 300037-IS 5/1/2014

INTRODUCTION:CAREFULLY READ THE CONTENTS OF THESE INSTRUCTIONS, AS THEY INDICATE THE CORRECT STEP BY STEP PROCEDURE TO ASSEMBLE THE PRODUCT. THE CARTON CONTENTS PAGE(S) WILL IDENTIFY THE ASSEMBLY PARTS. BEFORE PROCEEDING WITH THE ASSEMBLY PROCESS, MATCHTHE CARTON CONTENTS TO THE STATED CONTENTS TO ENSURE THERE ARE NO MISSING PARTS. IN THE EVENT OF ASSEMBLY PROBLEMS OR MISSING PARTS,PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT. PHONE: 1-800-968-6991WEBSITE: WWW.TOBACCOFIXTURES.COM CAUTION:ASSEMBLED TOBACCO FIXTURES MAY BE VERY HEAVY. DO NOT ATTEMPT TO LIFT OR MOVE WITHOUT ASSISTANCE. THE MANUFACTURER OF THIS DISPLAY ASSUMES NO LIABILITY FOR INJURY CAUSED BY IMPROPER ASSEMBLY/INSTALLATION OF THIS DISPLAY NUMBER OF PEOPLE REQUIRED TO ASSEMBLE UNIT: (1) ASSEMBLY TOOLS REQUIRED:NONE

THE FOLLOWING ITEMS ARE COVERED BY THESE INSTRUCTIONS; 300037 ADJUSTABLE WIDTH PUSHER KIT300038 ADJUSTABLE WIDTH PUSHER ADD-ON 300039 NARROW WIDTH PUSHER KIT300036 NARROW WIDTH PUSHER ADD-ON NOTE - THESE KITS ARE FOR USE IN BOTH BLACK AND SILVER TOBACCO FIXTURES.




PAGE 2 OF 14 300037-IS 5/1/2014

INTRODUCTION

NOTE - THE NARROW WIDTH PUSHER KIT IS A MULTIPURPOSE SPRING LOAD TRAY DESIGNED TO HANDLE PRODUCTS THAT ARE SMALLER ANDNARROWER THAN REGULAR CIGARETTE PACKS. NOTE - THE ADJUSTABLE WIDTH PUSHER KIT IS A MULTIPURPOSE SPRING LOAD TRAY DESIGNED TO HANDLE PRODUCTS THAT ARE LARGER AND WIDER THAN REGULAR CIGARETTEPACKS.

ADJUSTABLE WIDTHPUSHER KIT SHOWN

NARROW WIDTHPUSHER KIT SHOWN

INSTALLATION INSTRUCTIONS; PAGES 3 - 5 PAGES 6 - 7 PAGES 8 PAGES 9 - 10 PAGES 11 - 12 PAGES 13 -14

CARTON CONTENTS CONFIGURING THE PUSHER KITS INSTALLING SIGN CHANNELS INSTALLING AND REMOVING TRACKS INSTALLING AND REMOVING SPRING LOAD TRAYS CONNECTING THE PUSHER KITS TOGETHER



S M O K E LE S S T O B A C C O S P R IN G LO A D T R A Y , 1 P A C K

ITEM # DESCRIPTION QTY1A TRACK 11B DIVIDER 51C PUSHER, ADJUSTABLE WIDTH 41D SIGN CHANNEL, BLACK 11E SIGN CHANNEL, SILVER 11F TRAY BASE 1

ADJUSTABLE WIDTH PUSHER KIT

ADJUSTABLE WIDTH PUSHER KIT & ADD-ONNARROW WIDTH PUSHER KIT & ADD-ON

PAGE 3 OF 14 300037-IS 5/1/2014

CARTON CONTENTS

1E

1D

UNIT DIMENSIONS: POLYBAGGED KITUNIT WEIGHT: 2 LBS. CARTON DIMENSIONS: 23-3/8" X 13-7/8" X 12-1/2"CARTON WEIGHT: 15 LBS.(BULK PACKED 6 PER CARTON)

1F

1B

1A

1C

1A




ITEM # DESCRIPTION QTY2A TRACK 12B PUSHER, NARROW WIDTH 42C PUSHER, ADJUSTABLE WIDTH 32D SIGN CHANNEL, BLACK 12E SIGN CHANNEL, SILVER 12F TRAY BASE 1

NARROW WIDTH PUSHER KIT


PAGE 4 OF 14 300037-IS 5/1/2014

CARTON CONTENTS

2E

2D

UNIT DIMENSIONS: POLYBAGGED KITUNIT WEIGHT: 2-1/2 LBS. CARTON DIMENSIONS: 23-3/8" X 13-7/8" X 12-1/2"CARTON WEIGHT: 17 LBS.(BULK PACKED 6 PER CARTON)

2F

2B

1A

2C

2A




ITEM # DESCRIPTION QTY3A DIVIDER 13B PUSHER, ADJUSTABLE WIDTH 1

ADJUSTABLE WIDTH PUSHER ADD-ONITEM # DESCRIPTION QTY

4A PUSHER, NARROW WIDTH 14B PUSHER, ADJUSTABLE WIDTH 1

NARROW WIDTH PUSHER ADD-ON


PAGE 5 OF 14 300037-IS 5/1/2014

CARTON CONTENTS

3B

3A

UNIT DIMENSIONS: POLYBAGGED KITUNIT WEIGHT: LESS THAN 1 LBS. CARTON DIMENSIONS: 18" X 18" X 18"CARTON WEIGHT: 23 LBS.(BULK PACKED 50 PER CARTON)

4A

4B

UNIT DIMENSIONS: POLYBAGGED KITUNIT WEIGHT: LESS THAN 1 LBS. CARTON DIMENSIONS: 18" X 18" X 18"CARTON WEIGHT: 14 LBS.(BULK PACKED 50 PER CARTON)




PAGE 6 OF 14 300037-IS 5/1/2014

INSTALLATION INSTRUCTIONS

CONFIGURING THE PUSHER KITS NOTE - THE ADJUSTABLE AND NARROW WIDTH PUSHER KITS ARE MULTIPURPOSE SPRING LOAD TRAYS DESIGNEDTO HANDLE A WIDE VARIETY OF DIFFERENT PRODUCTSIZES. PARTS FROM THE ADJUSTABLE AND NARROW WIDTHKITS ARE INTERCHANGABLE AND CAN BE COMBINED AS NEEDED. NOTE - INSTALLATION IS SIMILAR FOR ALL ADJUSTABLE AND NARROWWIDTH PUSHER KITS AND ADD-ONS. STEP 1 - DETERMINE WHAT PRODUCTS WILL BE MERCHANDISED IN THE PUSHER KITS AND CONFIGURE THEM AS NEEDED. (VIEW 1) NOTE - SEE PAGE 7 FOR MORE INFORMATION.

VIEW 1


TRAY BASE

DIVIDERS

PUSHERS




PAGE 7 OF 14 300037-IS 5/1/2014


VIEW 2 (SIDE VIEW)

NOTE - TO INSTALL A DIVIDER OR PUSHER ON THE TRAY BASE, ALIGNTHE TWO SETS OF TABS ON THE DIVIDER OR PUSHER WITH THE

TWO SLOTS IN THE TRAY BASE AND PUSH IT INTO PLACE. (VIEW 2)

PUSHEVENLY

PUSHEVENLY

NOTE - WHEN INSTALLING A DIVIDER OR PUSHER ON THE TRAYBASE, PUSH EVENLY ON BOTH ENDS. MAKE SURE THAT THE PUSHER OR DIVIDER STAYS ALIGNED WITH THE OUTSIDE EDGEOF THE TRAY BASE.(VIEW 3 AND VIEW 4)

VIEW 3 (TOP VIEW) VIEW 4 (TOP VIEW)

GOOD

ALIGNMENT

BAD

ALIGNMENT

CONFIGURING THE PUSHERKITS (CONTINUED)




PAGE 8 OF 14 300037-IS 5/1/2014


INSTALLING SIGN CHANNELS STEP 2 - BASED ON THE COLOR OF THE TOBACCO FIXTURE, SELECT THE APPROPRIATE COLOR SIGN CHANNEL FOR THE PUSHER KIT. STEP 3 - HOOK THE SIGN CHANNEL ONTO THE FRONT OF THE TRAY BASE AND SNAP IT INTO PLACE. (VIEW 6 AND VIEW 7) NOTE - MAKE SURE THE SIGN CHANNEL IS CENTERED ON THE TRAY BASE FROM SIDE TO SIDE. (VIEW 5)

VIEW 5 (FRONT VIEW)

VIEW 6

VIEW 7

CENTER

SIGN CHANNEL


TRAY BASE




PAGE 9 OF 14 300037-IS 5/1/2014

VIEW 8

VIEW 9

VIEW 10


(3) TOBACCO FIXTURE SHELVES SHOWN

INSTALLING TRACKS STEP 4 - LOCATE THE 3 SLOTS ON THE TOBACCO FIXTURE SHELF WHERE THE TRACK WILL BE INSTALLED. POSITION THE TRACK SO THAT IT IS FACING FORWARD, AND LOWER IT INTO PLACE ON THE SHELF. (VIEW 9 AND VIEW 10) STEP 5 - PUSH DOWN ON THE BACK 2 SETS OF TABS ON THE TRACK UNTIL THEY SNAP INTO PLACE ON THE TOBACCO FIXTURE SHELF, THEN PUSH DOWN ON THE FRONT 2 SETS OF TABS ON THE TRACK UNTIL THEY ALSO SNAP INTO PLACE ON THE SHELF. (VIEW 8 AND VIEW 10) STEP 6 - MAKE SURE THAT THE TRACK IS PROPERLY SECURED TO THE TOBACCO FIXTURE SHELF. ADJUST THE LOCATION OF THE TRACK FROM SIDE TO SIDE AS NEEDED.

BOTTOM SIDEOF TRACKSHOWN

BACK TABS

FRONT TABS

BACKTABS

FRONT TABS

BACKSLOT

FRONTSLOTS




PAGE 10 OF 14 300037-IS 5/1/2014

VIEW 11

VIEW 12

VIEW 13



REMOVING TRACKS STEP 7 - REACH UNDERNEATH THE TOBACCO FIXTURE SHELF AND LOCATE THE 4 SETS OF TABS ATTACHING THE TRACK. (VIEW 11 AND VIEW 12) STEP 8 - SQUEEZE THE 2 SETS OF TABS ON THE BACK OF THE TRACK AND GENTLY PUSH UPWARD UNTIL THEY ARE NO LONGER ATTACHED TO THE TOBACCO FIXTURE SHELF. REPEAT FOR THE 2 SETS OF TABS ON THE FRONT OF THE TRACK. (VIEW 11 AND VIEW 12) STEP 9 - REMOVE THE TRACK FROM THE TOBACCO FIXTURE SHELF. (VIEW 13)

BOTTOM SIDEOF TRACKSHOWN

SQUEEZE TABSTOGETHER

BACK TABS

FRONT TABS

BACKTABS

FRONT TABS




PAGE 11 OF 14 300037-IS 5/1/2014

VIEW 14

VIEW 15

VIEW 16


TRAY "T's"


BOTTOM SIDE OF STANDARD 5 WIDE SPRINGLOAD TRAYSHOWN

STANDARDTRACKSHOWN

TRACK SLOTS

NOTE - THE ADJUSTABLE AND NARROW WIDTH PUSHER KITS ARE DESIGNED TO FIT INTO THE SAME SPACE AS A STANDARD 5 WIDE SPRING LOAD TRAY. STEP 10 - DETERMINE WHERE THE PUSHER KIT WILL BE INSTALLED, AND WHICH EXISTING SPRING LOAD TRAY WILL NEED TO BE REMOVED. STEP 11 - PUSH THE EXISTING SPRING LOAD TRAY SLIGHTLY TOTHE BACK UNTIL THE "T's" ON THE BOTTOM OF THE TRAY ALIGN WITH THE SLOTS IN THE TRACK. (VIEW 14 AND VIEW 15) STEP 12 - LIFT THE SPRING LOADTRAY UPWARD UNTIL IT IS NO LONGER ATTACHED TO THE TRACK, AND COMPLETELY REMOVE IT FROM THE TOBACCO FIXTURE SHELF. RECYLE/DISCARD AS NEEDED. (VIEW 16)

EXISTING SPRINGLOAD TRAYS

REMOVING SPRING LOAD TRAYS




PAGE 12 OF 14 300037-IS 5/1/2014

VIEW 18

STANDARD TRACKSHOWN


VIEW 17

ADJUSTABLE WIDTHPUSHER KIT SHOWN ON(3) TOBACCO FIXTURE

SHELVES

VIEW 19

BOTTOM SIDE OFADJUSTABLE WIDTHPUSHER KIT SHOWN

INSTALLING SPRING LOAD TRAYS STEP 13 - TO INSTALL, ALIGN THE "T's" ON THE BOTTOM OF THE PUSHER KIT WITH THE SLOTS IN THE APPROPRIATE TRACK. (VIEW 18 AND VIEW 19) STEP 14 - LOWER THE PUSHER KIT INTO PLACE, THEN PULL IT SLIGHTLY FORWARD TO MAKE SURE IT IS ENGAGED WITH THE TRACK AND IS SITTING PROPERLY ON THE SHELF. (VIEW 17)

TRACKSLOTS

TRAY "T's"




PAGE 13 OF 14 300037-IS 5/1/2014


CONNECTING THE PUSHER KITS TOGETHER NOTE - THE ADJUSTABLE AND NARROW WIDTHPUSHER KITS CAN BE CONNECTED TOGETHERTO FACILITATE LOADING PRODUCT. STEP 15 - CONNECT THE ADJUSTABLE AND NARROW WIDTH PUSHER KITS TOGETHER AS NEEDED. (VIEW 20) IMPORTANT - NO MORE THAN (4) ADJUSTABLE AND NARROW WIDTH PUSHER KITS SHOULD BE CONNECTED TOGETHER. NOTE - CONNECTING THE ADJUSTABLE AND NARROW WIDTH PUSHER KITS TOGETHER IS OPTIONAL. NOTE - SEE PAGE 14 FOR MORE INFORMATION.

VIEW 20ADJUSTABLE WIDTH

PUSHER KITS SHOWN ON(3) TOBACCO FIXTURE

SHELVES

CONNECTING THEPUSHER KITS ALLOWSTHEM TO BE PULLED

OUT TOGETHER




PAGE 14 OF 14 300037-IS 5/1/2014


CONNECTING THE PUSHER KITS TOGETHER (CONTINUED) A) PUSH THE CENTER TAB INWARD UNTIL THE POST IS FLUSH WITH THE OUTSIDE FACE OF THE TRAY BASE. B) ALIGN THE FRONT AND BACK POSTS WITH THE MATING SLOTS, AND PUSH THE TRAY BASES TOGETHER. C) SLIDE THE TRAY BASES IN OPPOSITE DIRECTIONS UNTIL THEY LOCK TOGETHER. D) MAKE SURE THE CENTER POST LOCKSINTO PLACE IN THE CENTER SLOT. VIEW 23 (BOTTOM SIDE)

FRONTPOST

BACKPOST

CENTER TABAND POST

FRONTSLOT

BACKSLOT

CENTERSLOT

A

C

B

D

B

VIEW 21 (SIDE VIEW) VIEW 22 (SIDE VIEW)

item # description qty 1a smokeless tobacco …...2d unit dimensions: polybagged kit unit weight:...

Documents