Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-372-2888, 9 a.m.-5 p.m., EST, Monday-Friday.

ITEM #0102967

PREMIUM WOOD CLOSET SYSTEM

Español p. 15

MODEL #LG-CL-V11-10

Safety Information .........................................................................................................................

Package Contents .........................................................................................................................

Hardware Contents .......................................................................................................................

Preparation ....................................................................................................................................

Assembly Instructions ....................................................................................................................

Care and Maintenance ..................................................................................................................

Replacement Parts List......................................... ..........................................................................

2

3

4

Warnings and Cautions.................................................................................................................. 5

5

7

Assembly Instructions For Shortening (Optional) . ......................................................................... 6

13

13

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 1-888-372-2888, 9 a.m. - 5 p.m., ES

1. Hire an insured remodeler for installation if the closet system should be shortened.

2. Keep the enclosed touch up paint (V) in a safe place and out of children’s reach or dispose properly after using.

3. Use this unit for its intended purpose only. Do not use shelves as step ladder.

4. Keep the screwdriver and the enclosed Allen wrench (GG) to periodically check all screws andto ensure they remain tightly fastened.

5. Two or more persons must work together to install the unit onto the wall.

T, Monday-Friday.

2

TABLE OF CONTENTS

3

PACKAGE CONTENTS

Part Description QuantityA 1

1

2

11

1

3

11

Side Table Top - LeftSide Table Top - Right

Floating Side ShelfBottom Brace

33332

Drawer Back

Drawer FrontDrawer Side - LeftDrawer Side - Right

Drawer BottomTop Back Wall Cleat

Center Table TopShort Side PanelCenter Side Panel - Left 1Center Side Panel - Right 1

12

Long Side Panel Adjustable Middle Shelf Fixed Shelf 2Back Panel 2Bottom Assembly 1Long Metal Rod Short Metal Rod

BCDEFGHIJK

Part Description Quantity

LMNO

PQRSTU

1Touch-up PaintV1Wood CleatW2

1

9

Bottom Back Wall CleatLeft Wood Support (preassembled)

1.5 Phillips Pan Head Wood Screw (preassembled)

X

Y

Z

1Front Wood Support (preassembled)

Y1

L

C

F

B

L

M

O

G

U

E

S

Q

T

R

P

K

D

NA

V

-

Drawer

X

HI

P

W

J

4

HARDWARE CONTENTS

QuantityPicture(Shown to size)

M6x35Screw

28

Part

1 in. PhillipsFlat Head Wood Screw

24

L- Bracket

Lock Washer

Floating ShelfSupport

Wall Anchor28

18

5/8 in. Screw

AA

DD

EE

JJCC

Description QuantityPicture(Shown to size)

MetalKnob

3

Part

HH

Description

BB Metal KnobScrew

3

18

KK 4

AdjustableMetal Pin

8

28

II

2 in. Phillips Pan Head Wood Screw

6

1GG

Metal RodSupport

Allen Wrench

LL

MM

4NN

1FF Level

Floating ShelfSupport Screw(M6x20)

4OO

5

PREPARATION

WARNINGS AND CAUTIONS

WARNING

CAUTION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and diagram above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time:

Two adults may be required for safe assembly.

Assemble the parts on a soft, non-abrasive surface, such as carpeting, to avoid scratching the finish.

Use care when handling.

180 minutes

Tools Required for Assembly (not included): Screwgun or Phillips Screwdriver, Marking Pencil, Hand Drill, Drill Bit, Tape Measure, Hammer, Step Ladder, Table Saw, Pipe Cutter, Stud Finder, Level

NOTE: These tools are used only if the unitis too wide for the closet.

.

Do not allow children to climb or play in or around this product..

The wall anchors are for masonry or solid wall fixings only.

Distribute weight evenly.

.

.

This unit can hold up to 66 lbs. load per shelf, drawer or metal rod.

6

1. If the unit is to be shortened, use screwgun or Phillips screwdriver to unscrew left wood support (preassembled) (Y) and front wood support (preassembled) (Y1), from closet side table top - left (A). Keep the 1.5 in. Phillips pan head wood screws (preassembled) (Z), left wood support (preassembled) (Y) and front wood support (preassembled) (Y1) taken for later use. (Fig. 1)

Note: It is recommended to shorten left side of side table top - left (A) only. Use marking pencil to markthe cutting line. (Fig. 2)

2. Use a table saw to cut the closet side table top - left (A), front wood support (preassembled) (Y1) and top back wall cleat (U). Use pipe cutter to cut the long metal rod (L). Cut only one side of the closet, if the closet is smaller than 10 ft. The choice is yours. Do not cut the parts using a hand saw only, as it may cause damage to the parts. Place the beveled edge down against the fence to ensure a clean cut. Help from an insured remodeler is highly recommended. (Fig. 3, 4, 5, 6, 7, 8)

Note: Front wood support (preassembled) (Y1) should be shorter than the side table top - left (A) about10 mm from the shortened edge.

3. Apply paint on the cut edge using the provided touch-up paint (V). (Fig. 9, 10, 11)

4. Screw the left wood support (preassembled) (Y) and front wood support (preassembled) (Y1) back on the shortened closet side table top - left (A) using the same 1.5 in. Phillips pan head wood screws (preassembled) (Z) taken from Step 1. (Fig 12)

ASSEMBLY INSTRUCTIONS FOR SHORTENING (OPTIONAL)

This is usable in a closet space which is smaller than the actual size of this product. If your closet is 10 ft. wide or larger, there is no need to shorten this unit. Hire an insured remodeler for installation.

NOTE: SHORTEN THIS CLOSET ON ONE SIDE ONLY

Fig. 9

A

V

Fig. 10

UV

CORRECTNOT

Fig. 6

CORRECTNOT

Fig. 8

L

Z

Y1LZ

LY

CORRECT

Fig. 7

L

L

CORRECT

Fig. 5

A

Fig. 3 Fig. 4Fig. 2

U

Fig. 1

Fig. 11 Fig. 12

Y1V

A

A

Y1

A

Y1Z

Y

Y1

Z

LA

7

2. Using a 1/4 in. drill bit, drill 10 holes intothe pre-marked keyhole positions. (Fig. 2)

Fig. 2

ASSEMBLY INSTRUCTIONS

1. Hold the top back wall cleat (U) against the wall at the desired height (minimum of 75 in). Mark the keyhole positions with a marking pencil. (A level should be used. If you don’t have available level, use the enclosed level (FF). Align and level the enclosed level (FF) with top back wall cleat (U) then secure with 5/8 in. screws (CC). (Fig. 1)

NOTE: Use step ladder if necessary. While 75 in. is the minimum, 84 - 90 in. is considered the optimum if your closet height permits. Use a stud finder to locate studs.

Fig. 1

U

U

FF

CC

Hardware Used

x 2

x 1

5/8 in. ScrewCC

FF Level

Fig. 3

8

4. Install top back wall cleat (U) usinga 2 in. Phillips pan head wood screw (DD) and fully tighten with screwgun. (A Phillips screwdriver may also be used). (Fig. 4)

5. Complete installation of top back wall cleat (U).(Fig. 5)

Fig. 4

Fig. 5

Hardware Used

2 in.Phillips Pan Head Wood Screw

DD

U

DD

x 10

U

U

3. Insert wall anchors (JJ) into all screw holes exceptwhere a stud exists. (Fig. 3)

NOTE: 3.a. Some holes may coincidewith wall studs. If this occurs, use screws onlyin these holes.

3.b. Every hole must have either a2 in. Phillips pan head wood screw (DD) or wall anchor (JJ) for support.

Hardware Used

x 10Wall AnchorJJ

JJ

9

7. Hang the assembled unit on the center of topback cleat (U). Use step ladder if necessary. Insertbottom back wall cleat (X) onto slot located onmiddle part of center side panels - left/right (E,F).Mark the keyhole positions with a marking pencil.Using wall anchors (JJ) and 2 in. Phillips panhead wood screws (DD), repeat steps 1through 5 to install the bottom back wallcleat (X). (Fig. 7)

Note: 2 people must work together to hangthe unit in place.

6. Assemble center table top (C), fixed shelf (I) and bottom assembly (K) to center side panel - left (E). Fully secure with M6x35 screws (AA), lock washers (MM) and tighten using the Allen wrench (GG). Gently slide back panels (J) between grooves of fixed shelf (I), bottom assembly (K) and center side panel- left (E). Ensure that wood cleat (W) is inserted between two back panels (J). Attach the other center side panel- right (F) to the preassembled unit and secure with M6x35 screws (AA) and lock washers (MM). Fully tighten with Allen wrench (GG). (Fig. 6)

x 1

x 16

Hardware Used

Hardware Used

x 16M6x35Screw

AA

GG Allen Wrench

Lock WasherMM

Fig. 6

IIE

C

AAGG

K

MM

F

JW

J

Fig. 7

U

U

U

X

X

x 8Wall AnchorJJ

2 in.Phillips Pan Head Wood Screw

DD x 8

E

E

F

10

Hardware Used

M6x35Screw

AA

GG Allen Wrench x 1

x 6

x 6Lock WasherMM

MM

MM

9. Attach short side panel (D) to the assembledunit. Secure with three M6x35 screws (AA) andlock washers (MM) then tighten with Allen wrench (GG). Repeat step to assemble the long side panel (G). Insert bottom brace (O) between center unit and long side panel (G) then secure to center side panel - right (F)and long side panel (G) using two L- brackets (KK). Secure L-brackets (KK) tightly with 5/8 in. screws (CC) using Phillips screwdriver. (Fig. 9)

Fig. 9

Hardware Used

M6x35Screw

AA

GG Allen Wrench x 1

x 6

AA

AA

O

GGG

GG

D

x 6Lock WasherMM

Fig. 8

AAGG

U

AB

MM

8. Attach side table top - left (A) to the centerunit. Make sure it was properly hung onto top back wall cleat (U). Secure to center unit using three M6x35 screws (AA) and lock washers (MM) then tighten with Allen wrench (GG). Repeat step to assemble side table top - right (B). (Fig. 8)

U

x 4

x 2

5/8 in. ScrewCC

CC

KK

KK

L- Bracket

F

11. Attach metal rod support (EE) underneathside table tops (A,B) and floating side shelf (N) using three, 5/8 in. screws (CC) for each. Fully tighten 5/8 in. screws (CC) with Phillipsscrewdriver then place long metal rod (L)on the installed metal rod support (EE). (Fig. 11) NOTE: Use long metal rod (L) for side table top (A,B) and use short metal rod (M)for floating side shelf (N).

Fig. 11

A

B

N

CC

CC

LM

EEEE

11

10. Insert adjustable metal pins (LL)into the space provided on the center unit at your desired level. Gently placeadjustable middle shelves (H) on top of the installed adjustable metal pins (LL). Attach floating side shelfsupport (NN) on panels (F, G) at your desired level. Secure tightly with the provided floating side shelf support screws (OO) then tighten with Allen wrench (GG). Secure bottom brace (O) to side panels (F, G) with L-bracket (KK). Secure L-brackets (KK) using 5/8 in. screws (CC) and tighten with Phillips screwdriver. (Fig. 10)

NOTE: The adjustable middle shelves (H) and floating side shelf (N) can be adjusted now or in the future based on the clothing you will hang.

Fig. 10

Hardware Used

x 4

x 2

x 8

x 4

5/8 in. ScrewCC

KK L- Bracket

AdjustableMetal Pin

LL

Floating Side Shelf Support

NN

Hardware Used

x 18

x 6

5/8 in. ScrewCC

EE Metal RodSupport

KK

CC

LL

O

O OO

F N

H

H

G

GGNN

x 4

x 1

OO

GG

Floating Side Shelf SupportScrew

OO

GG Allen wrench

12. With grooves facing inward, attach drawer front (P) and drawer back (S) to drawer side - Left (Q) using four 1 in. Phillips flat head wood screws (BB). Gently slide drawer bottom (T) into grooves of drawer front (P), drawer side left (Q) and back (S). Attach drawer side - right (R) to drawer front (P) and drawer back (S)using four 1 in. Phillips flat head wood screws (BB). Attach metal knob (HH) to drawer front (P) by using metal knob screw (II). Fully tighten all screws using Phillips screwdriver. (Fig.12)

NOTE: Repeat step to assemble theother two drawers.

Fig. 12

Fig. 13

BB

Q S

R

PII

HH T

OO

12

13. Insert drawers on the space providedof the pre-assembled closet. (Fig. 13)

NOTE: Press the side mechanisms while sliding drawers in, as shown.

Hardware Used

1 in. PhillipsFlat Head WoodScrew

x 24

x 3

BB

II Metal KnobScrew

x 3HH MetalKnob

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-888-372-2888, 9 a.m.-5 p.m.,

CARE AND MAINTENANCE

• Periodically check to make certain all components are properly positioned, free from damage and firmly connected.

• Wipe clean using a damp cloth and a mild cleaner. Wipe dry with a clean cloth.

EST, Monday-Friday.

noitpircseD traP Part #Center Table Top LG-CL-V11-10C

LG-CL-V11-10DLG-CL-V11-10ELG-CL-V11-10FLG-CL-V11-10GLG-CL-V11-10HLG-CL-V11-10ILG-CL-V11-10JLG-CL-V11-10K

LG-CL-V11-10OLG-CL-V11-10PLG-CL-V11-10QLG-CL-V11-10RLG-CL-V11-10SLG-CL-V11-10T

LG-CL-V11-10V

LG-CL-V11-10AA

LG-CL-V11-10BB

LG-CL-V11-10CC

LG-CL-V11-10DD

LG-CL-V11-10EELG-CL-V11-10GGLG-CL-V11-10HHLG-CL-V11-10IILG-CL-V11-10JJLG-CL-V11-10KKLG-CL-V11-10LLLG-CL-V11-10MMLG-CL-V11-10NNLG-CL-V11-10OO

Short Side PanelCenter Side Panel - LeftCenter Side Panel - RightLong Side Panel Adjustable Middle Shelf Fixed Shelf Back Panel Bottom Assembly

CDEFGHIJK

LG-CL-V11-10LLong Metal RodLLG-CL-V11-10MShort Metal RodM

O Bottom BraceDrawer FrontDrawer Side - LeftDrawer Side - RightDrawer BackDrawer Bottom

Touch-up Paint

M6x35 Screw1 in. Phillips Flat Head Wood Screw

2 in. Phillips Pan Head Wood Screw

PQRST

VLG-CL-V11-10UTop Back Wall CleatU

LG-CL-V11-10WWood CleatWLG-CL-V11-10XBottom Back Wall CleatX

AA

BB

CC

DD

EEGGHHIIJJKKLLMMNN

OO

L- BracketWall Anchor

5/8 in. Screw

Adjustable Metal PinLock WasherFloating Shelf SupportFloating Shelf SupportScrew - M6x20

Metal Rod Support

Metal KnobAllen Wrench

Metal Knob Screw

F GE

H

I

C

DC

E F

13

Side table tops (A, B) and floating side shelf (N)are available in the Lowe’s store where you purchased your closet system.

A

B

L

N

L M

14

OK

Q TS

P R

BB CC

GG

KK

II V

JJ

LL

AA DD

EE

Printed in Thailand

HH

J

J

U

MM NN OO