PLEASE READ ENTIRELY THESE INSTRUCTIONS FOR THE PROPER USE

OF THE PRODUCT!

INSTRUCTIONS FOR USE AND SET UP

REV. 25-10-2016

CLONE Rc2 4T16 MODELS ROLLING CODE DUPLICATOR

The CLONE RC2 4T allows to create a new radio control of the following brands with 433.92 MHz transmission frequency. To each button can be assigned a type, also different types that are in the list. Once identified the radio control to be generated, just carry out the programming procedure without needing a working one. Once you have programmed it, you have just to understand the receiver, following the instructions of the same receiver.

WHEN TO USE IT?

®DOORHANSKYMASTER

1Code

TRASMITTER (2-4) F350G

®NICE

2Code

SMILO

®DEA

3Code

MIO TR2-MIO TR4

®KEY

4Code

TXB44R TXB42R

®APRIMATIC

5Code

TR2-TR4TM2-TM4

®BENINCA

6Code

TO GO(2-4)WVCUPIDO(2-4)

®VDS

7Code

E010

®FAAC

8Code

XT4 433RC

®PUJOL

9Code

VARIO 1-3

®ERREKA

10Code

IRIS 4IRIS 2

®GIBIDI

11Code

DOMINO

®MOTORLINE

12Code

MX4SP

®MUTANCODE

14Code

CLEMSA TX1-TX2-TX4

®BFT

15Code

RCB(02-04)BFT MITTO(2-4)

®PUJOL

16Code

YELLOW

®SEAV

17Code

BE SMART S(2-4)BE HAPPY RS(1-2-3)

REPEAT THE SAME PROCESS FOR PROGRAMMING OTHER BUTTONS

At the same time press the buttons 1 and 2

After two seconds, the led flashes three times then turns offThe led starts flashing

1 - SET UP

2 - CHECK SET UP

Release buttons

At the same time press the buttons 3 and 4

The led turns on steady for four seconds and then turns off

HOW TO PROGRAM IT?

Release buttons The led starts flashing

Press the CLONE RC2 4T button for which you want to know the associated code

The led will emit an equal number of flashes for each programming code type

The led turns on every time you press the button to program

Press the button CLONE RC2 4T to program as many times as the code of the type to program on that button (see table)

The led will flash as many times as the code set to confirm the correct programming

Then press any other different button from the programmed one

By using a phillips head screwdriver, unscrew the screw at the back of the CLONE RC2 4T remote control.The remote control is powered by a 3V LITHIUM BATTERY with initials CR2032 Remove a dead battery and insert the new one paying attention to the correct polarity.

HOW TO REPLACE THE BATTERY?

WARNING: Do not disperse the old battery into the environment, but dispose it in dedicated waste container.

The HIDDEN KEY function to the 15 BFT code is obtained by pressing at the same time button 1 and 4

To the 5 APRIMATIC code, the function PRESS AT THE SAME TIME ALL FOUR KEYS, is obtained by pressing at the same time button 2 and 3

CLONE Rc2 4T16MODELS ROLLING CODE DUPLICATOR

NOTE FOR BFT

NOTE FOR APRIMATIC

REV

. 2

5-10

-201

6

Product designed and manufactured in Italy by

SILISYSTEM TECHNOLOGY s.r.l.Via Marconi, 38 - 81030 Sant’Arpino (CE)info@silisystem.com - www.silisystem.com

CONFORMITY DECLARATION

The CLONE RC2 4T radio control complies with the essential requirements of the following standards:

ETSI EN300 220-2 Short Range Device (SRD)EN 301 489-1 Electromagnetic Compatibility (EMC)

EN60950 Safety

With the current “SILISYSTEM TECHNOLOGY srl” declares that:The device “CLONE RC2 4T” has been proved in a typical configuration of installation and complies

with the essential requirements and the other relevant provisions laid down by Directive:

1999/5/CE (R&TTE Directive)CE/108/2004 (EMC Directive)CE/95/2006 (LVD Directive)

Andrea D'AliaSant Arpino (CE) 05/15/2015

Transmission frequency European Market: 433.92 MHz

CLONE Rc2 4T16 MODELS ROLLING CODE DUPLICATOR