iss 506 • setup guide (continued) iss 506 • setup guidethis guide provides quick start...
TRANSCRIPT
-
ISS 506 • Setup Guide
NOTE: For full installation, configuration, and operation details, refer to the ISS 506 User Guide, available at www.extron.com.
This guide provides quick start instructions for an experienced installer to set up and operate the Extron ISS 506 Integration Seamless Switchers, a family of seamless, scaling, video and stereo audio switchers.
Installation and Cabling Features
100-240V 50/60 Hz2A MAX
R/R-Y
SDIG/YVID
SB/CB-Y
HH/HV V
H/HV
RS232/422
1L R
R/R-Y
1
2
G/YVID
B/CB-Y
R/R-Y
G/YVID
B/CB-Y
H/HV V
H/HV VV R/R-Y
3
4
G/YVID
B/CB-Y
VID/Y
R-Y
VID
B-Y/C
V
G/Y
5
RR-Y
RESET
OUTPUT S
6
YC
B/B-Y
PROGRAMPREVIEW
RGB/R-Y, Y, B-Y
RGB/R-Y, Y, B-Y
2L R 3L R 4L R 5L R 6L R
INPUT S
L R
PREVIEW
FIXEDL R
PROGRAM
VARIABLEL R
LAN
LO-RESOUT
R-Y/R
C
Y/G
VID
B-Y/B
Y
Scan Converter
DVI
3G/HD-SDI3G/HD-SDIOUT
DVIOUT
PICTUREADJUSTMENTS
CONFIG
DETAIL
ZOOM
BRIGHT/CONT
COLOR/TINT
SIZE
POSITION
Rear Panel Front Panel
SDIVID/Y
5 6
RGB/R-Y, Y, B-Y
PREVIEWPROGRAM
111 13 12 14
2
5 10 7
3 4 6 8
9
Connectionsa AC power connector h Preview Output 15-pin HD connector
(RGB or component)
b Inputs 1 through 4 configurable BNC connectors i Optional Program Output connector(s) (RGB, component, RGBcvS, S-video, or composite) (DVI, scan converted low resolution, or 3G/HD-SDI†)
c Input 5 configurable BNC connectors j Output audio captive screw connectors (component, S-video, composite)
d Input 6 configurable mini-DIN and BNC connectors k LAN (Ethernet) RJ-45 port (S-video, composite, SDI/HD-SDI*, auto SDI)
e Input 1 through 6 audio captive screw connectors l RS-232/422 DB-9 port
f Program Output BNC connectors m Reset button (RGB or component)
g Program Output 15-pin HD connector n Configuration port (front panel) (RGB or component) (RS-232 only on a 2.5 mm TRS connector)
* An SDI or HD-SDI input is preset only when an optional SDI or HD-SDI input card is installed (DI/DVI, DI/SC, and DI/3G-SDI models).† The output for i depends on the optional output card installed (DI/DVI, SC, DI/SC, and DI/3G-SDI models).
Step 1 — Mounting
Turn off or disconnect all equipment power sources. For tabletop use, affix the rubber feet. For optional rack mounting, secure the supplied brackets (see image at right) and mount in a rack.
Step 2 — Video inputs
a. Inputs 1 through 4 — Connect RGB video, component video, S-video, or composite video to these female BNC connectors.
b. Input 5 — Connect NTSC or PAL component video, S-video, or composite video to these female BNC connectors as shown at right.
MBD 2492U Rack Mount Bracket(use four lower holes)
RGBHV Video
Input 1 through 4 Configurations
RGsB orComponent
Video
S-Video
CompositeVideo
RGBS or RGBcvS
Video H/HV V
G/YVID
H/HV VR/R-Y
R/R-Y
B/CB-Y
G/YVID
B/CB-Y
H/HV VR/R-Y
G/YVID
B/CB-Y
H/HV VR/R-Y
G/YVID
B/CB-Y
H/HV VR/R-Y
G/YVID
B/CB-Y
Component Video
VID/Y
R-Y B-Y/C
5
S-Video
VID/Y
R-Y B-Y/C
5
Composite Video
VID/Y
B-Y/C
5
R-Y
Input 5 Configurations
ISS 506 • Setup Guide (Continued)
-
2
c. Input 6 — Connect S-video, composite video or SDI/HD-SDI video to this female 4-pin mini-DIN or BNC connector as shown at right.
NOTE: The SDI or HD-SDI video input is available only if the optional SDI input board is installed.
Step 3 — Video outputs
a. Program outputs — Connect video devices to the 15-pin HD output female connector (shown at right) and the BNC connectors (shown below).
b. If an optional program output board is installed (see the ISS 506 User Guide, available at www.extron.com), connect a DVI-D (shown at right), 3G/HD-SDI (shown below right), or low resolution device (scan converted output), shown below, to the board.
c. Preview output — Connect a video device to the 15-pin HD connector.
Step 4 — Audio
a. Connect up to six stereo or mono audio inputs to the 5-pole captive screw input connectors.
b. Connect balanced or unbalanced stereo audio or mono audio devices to one or both of the program captive screw output connectors and the preview 5-pole captive screw output connector.
NOTE: The Variable Program audio output is adjustable using the front panel Volume control. The other audio outputs are not adjustable.
Step 5 — Serial ports
a. If desired, connect a control system or computer to the rear panel RS-232/RS-422 port, as shown below left.
b. If desired, connect a control system or computer to the front panel Configuration (RS-232) port. The optional 9-pin D to 2.5 mm mini jack TRS RS-232 cable, part number 70-335-01, can be used for this connection, as shown below right.
CONFIG
Sleeve (Gnd)Ring
Tip
RS-232 FunctionPin Function23578
TXRXGnd——
Transmit dataReceive dataSignal groundNot usedNot used
TX–RX–GndRX+TX+
Transmit data (–)Receive data (–)Signal groundReceive data (+)Transmit data (+)
RS-422RS232/422
15
69
VID6
YC
SDIVID6
YC
VID6
YC
SDI
Composite Video SDI or HD-SDI S-Video
SDI
Input 6 Configurations
RGBHVVideo
RGBSVideo
RGsB andComponent
Video
SH V
G/Y
RR-Y
B/B-Y
SH V
G/Y
RR-Y
B/B-Y
SH V
G/Y
RR-Y
B/B-Y
Program Output ConfigurationsDVI Video
3G/HD-SDI Video
R-Y/R
C
Y/G
VID
B-Y/B
Y
Component Video
S-Video
R-Y/R
C
Y/G
VID
B-Y/B
Y
Composite Video
R-Y/R
C
Y/G
VID
B-Y/B
Y
Scan Converted Output Configurations
NOTE: The ISS outputs S-video and composite video simultaneously.
Unbalanced Stereo Input Balanced Stereo InputDo not tin the wires!
TipRing
TipRing
LR
SleevesTip
Sleeve
SleeveTip
LR
Unbalanced Stereo Output Balanced Stereo Output
Tip
NO GROUND HERE
NO GROUND HERE
Tip
LR
Sleeves
TipRing
TipRing
LR
CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts).
ISS 506 • Setup Guide (Continued)
-
Step 6 — LAN (Ethernet) port
If desired, connect a network WAN or LAN hub, a control system, or computer to the Ethernet RJ-45 port. See the ISS 506 User Guide, available at www.extron.com.
• Network connection — Wire as a patch cable.
• Computer or control system connection — Wire the interface cable as a crossover cable.
NOTE: Defaults:
• RS-232 • 9600 baud • IP: 192.168.254.254 • Subnet: 255.255.0.0 • Gateway: 0.0.0.0 • DHCP off
See “Configure Ethernet and RS-232/RS-422 ports,” on the next page, to change the settings.
Step 7 — Power
AC power connector — Plug in a standard IEC power cord from a 100 to 240 VAC, 50 - 60 Hz power source into this receptacle.
Powering Up Apply power by connecting the power cord to an AC source. The switcher performs a self-test that displays the model name and the firmware version in the LCD screen. After approximately 2 seconds, the LCD screen reverts to its default display cycle, alternating between three displays: two showing the selected program and preview inputs and their rates, and the third showing the selected output rate.
Front Panel OperationsSelect an input
Press and release the desired Program or Preview input selection button. The button lights and the selected input displays on the program or preview monitor.
Switch the preview output to the program output
NOTE: Select the sub-effect and duration using the Effects Configuration menu.
1. For an effect to accompany the switch, press one of the Effects buttons.
Wipe — The image in the preview output “unrolls” over the top of the program output using the duration and sub-effect.
Dissolve — The previous program output fades out and the image from the preview output fades into the program output using the duration.
PIP — The image in the preview output appears in the program output as a picture-in-picture window using the duration and sub-effect.
Title — The image in the preview output appears on top of the program output as a title.
2. Press either the Cut or the Take button.
Cut — If Wipe or Dissolve is selected, the preview output switches to the program output with no effect.
If PIP or Title is selected, the preview output appears on top of the program output as a PIP window or title, with no effect.
Take — If Wipe or Dissolve is selected, the preview output switches to the program output with the effect selected in step 1 and sub-effect and duration.
If PIP is selected, the preview output appears on top of the program output as a PIP window, with the sub-effect and duration.
If Title is selected, the preview output appears on top of the program output as a title, with no effect.
A cable wired as T568A at one endand T568B at the other (Tx and Rx pairsreversed) is a "crossover" cable.
A cable wired the same at both ends iscalled a "straight-through" cable, becauseno pin/pair assignments are swapped.
12345678
RJ-45Connector
Insert TwistedPair Wires
Pins: Crossover CableCrossover Cable Straight-through Cable
Pin
1
2
3
4
5
6
7
8
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Pin
1
2
3
4
5
6
7
8
White-orange
White-green
Blue
White-blue
White-brown
Brown
T568BT568B
White-orange
OrangeOrange
White-green
Blue
White-blue
GreenGreen
White-brown
Brown
Wire color Wire colorEnd 1 End 2 End 1 End 2
Wire color Wire color
2sec.
2sec.
2sec.
Default Display Cycle
10sec.
ExtronISS 506 Vn .nn 2
sec.
IntegrationSeamlessSwitcher
Poweron
InitializingPlease Wait.. .
Prog #n {format}n .nkHz n .nHz
Prev #n {format}n .nkHz n .nHz
Output Rate{resolution) @{rate}
ISS 506Integration Seamless Switcher
VOLUME
ADJUST
ADJUST
TRANSITION
PICTUREADJUSTMENTS
CONFIG
PROGRAM
PREVIEW
EFFECTS
MENU NEXT
DETAIL
ZOOM
BRIGHT/CONT
COLOR/TINT
SIZE
POSITION
TAKECUT
PIP
TITLE
WIPE
DISSOLVE
LOGO 2/BLACK
LOGO 1/BLACK1 2 3 4 5 6
1 2 3 4 5 6 LOGO 2/BLACKLOGO 1/BLACK
FREEZE
FREEZE
CONFIG
PictureAdjustments LCD Volume
Effects(Wipe/PIP/Dissolve/Title)
Program Bus(Freeze/Input Selection/Logo)
Transition(Cut/Take)
Program Bus(Freeze/Input Selection/Logo)
EFFECTS
Menu Controls
Soft Right
Soft Left
Soft Up
Soft Down
Soft Center In
Soft Center Out
Soft Curtain In
Soft Curtain Out
Soft Square In
Soft Square Out
Soft Plus In
Soft Plus Out
Hard Right
Hard Left
Hard Up
Hard Down
Hard Center In
Hard Center Out
Hard Curtain In
Hard Curtain Out
Hard Square In
Hard Square Out
Hard Plus In
Hard Plus Out
Wipe and PIP sub-effects
ISS 506 • Setup Guide (Continued)
-
Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)
Extron Europe+31.33.453.4040
Extron Asia+65.6383.4400
Extron Japan+81.3.3511.7655
Extron China+86.21.3760.1568
Extron Middle East+971.4.2991800
Extron Korea+82.2.3444.1571
Extron India+91.80.3055.3777
© 2012 Extron Electronics All rights reserved. www.extron.com 68-1077-50 Rev. B 07 12
Recall and key a saved bitmapped image
NOTE: Bitmap images must first be captured using the Logo Capture submenu or uploaded via the LAN port.
1. Press and hold the Next button. Press and release the desired logo button. Release the Next button.
2. Rotate either Adjust knob to select black screen or a saved logo. Press the Next button.
3. Rotate the two Adjust knobs to position the logo as desired on the screen. Press the Next button.
4. Rotate either Adjust knob to select (< >) the desired method (RGB or level) for keying out (removing) the unwanted logo material.
5. If you selected RGB as the keying method, rotate the Adjust [ knob to select the color plane to key.
6. Rotate the Adjust { knob to key out the unwanted material.
Adjust the Variable Audio outputRotate the Volume knob to increase or decrease the loudness or the Variable Audio output.
Recall user presets
NOTE: You must have saved user presets using the menu system (refer to the ISS 506 User Guide, available at www.extron.com) before you can recall them.
Repeatedly press and release the input button to cycle through the saved user presets (up to three) for that input.
Configure Ethernet and RS-232/RS-422 ports1. Press and hold
Next while you simultaneously press Color/Tint, and Detail to access the Edit Comm Settings submenu.
2. Press Next to page through the submenu.
Serial Port Mode: Rotate the Adjust [ knob to select the baud rate and the Adjust { knob to select the protocol.
DHCP: Rotate either knob to select (< >) On or Off.
IP Address, Subnet Mask, and Gateway Address: Rotate the Adjust [ knob to select (blinking) an octet and the Adjust { knob to change the selected octet.
ISS 506 Control ProgramThe control program is on the Extron Software Products DVD. Run the program on a PC connected to either of the serial ports or the LAN port (see l, n, or k, on page 1). The program must be installed and cannot be run from the DVD.
NOTE: For details on installing and operating the program, refer to the ISS 506 User Guide, available at www.extron.com.
HTML PagesThe HTML pages are built into the switcher and can be accessed using a Web browser such as Microsoft® Internet Explorer. Enter the IP address of the unit in the Address field of the browser (192.168.254.254 is the default value).
PICTUREADJUSTMENTS
NEXTDETAIL
ZOOM
BRIGHT/CONT
COLOR/TINT
SIZE MENU
POSITION
ISS 506 • Setup Guide (Continued)